# Airbus Service Bulletin A340-27-4214

Copy: No revision named ("A340-27-4214 R00"), 53 pages: PDF https://openairdocs.org/files/sha256/07/24/0724b413484149f30eb011f7303b57aa87a15de674841e5e2da9758d7e696455; text https://openairdocs.org/service-documents/airbus/a340-27-4214/file/0724b4134841.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2022-0522, the docket of AD 2022-16-06. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A340-27-4214
- Page: https://openairdocs.org/service-documents/airbus/a340-27-4214

## Text (53 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2022-0522, the docket of AD 2022-16-06. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 1
CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
 
The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.
MANDATORY MANDATORY MANDATORY
ATA SYSTEM: 27
TITLE: FLIGHT CONTROLS - TRIMMABLE HORIZONTAL STABILIZER (THS)
HYDRAULIC ACTUATION - INSTALL ELSD ON THSA
MODIFICATION No.:
205979S33745
206264S33801

### Page 2

A340
SERVICE BULLETIN
SUMMARY
REV 00 Oct 12/20 A340-27-4214
Page 2
ATA SYSTEM: 27
TITLE: FLIGHT CONTROLS - TRIMMABLE HORIZONTAL STABILIZER (THS)
HYDRAULIC ACTUATION - INSTALL ELSD ON THSA
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
CONF 001
MODIFICATION CLASSIFICATION
MAJOR 205979S33745 206264S33801
MINOR None
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
CONF 002
MODIFICATION CLASSIFICATION
MAJOR 205979S33745 206264S33801
MINOR None
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
CONF ALL
B. REASON
(1) History
The Trimmable Horizontal Stabilizer (THS) actuator has a fail-safe design: each
attachment, upper and lower, has two load paths, a normally loaded primary load
path and a secondary load path, which is only engaged in case of primary load path
rupture.
When the secondary load path is engaged, the design purpose was to generate a stall
of the unit by friction and to detect it by the position monitoring.
It has been demonstrated by test that the upper secondary load path may not stall
correctly in some cases.
(2) Objective/Action
Hence a new device has been developed, called Electrical Load Sensing Device (ELSD)
and manufactured by Collins Aerospace, which aims at detecting the engagement on
the secondary load path.
This Service Bulletin details instructions for installation and activation of the ELSD,
following the wiring provisions embodied.
(3) Advantages
Accomplishment of this Service Bulletin will allow to detect upper secondary load path
engagement. The periodic detailed inspection of THS actuator upper attachments for
secondary load path loading will be preserved.

### Page 3

A340
SERVICE BULLETIN
SUMMARY
REV 00 Oct 12/20 A340-27-4214
Page 3
(4) Operational/Maintenance Consequences
The Operational/Maintenance Consequences of this Service Bulletin are covered by
the update of the affected publications detailed in "PLANNING INFORMATION".
C. GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE MANDATORY COST SAVING NO
A/C OPERATION
AFFECTED
NO VENDOR SB NO
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD YES
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO
NOTE: Service Bulletin must be accomplished.
D. MAINTENANCE CONFIGURATION
CONF 001
No specific aircraft maintenance configuration required.
CONF 002
No specific aircraft maintenance configuration required.
CONF ALL
E. MATERIAL PRICE INFORMATION
CONF 001
(1) Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
(a) T ask set A340-A-27-XX-4214-01000-93AA-A Modification to the Trimmable
Horizontal Stabilizer Actuator (THSA) by installation and activation of the
Electrical Load Sensing Device (ELSD)
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Aircraft standard tools See SB See Note Pin, pitch trim control
Components See SB See Note Bolt, lead, nut, screw, washer,
placard
Equipment See SB See Note ELSD
NOTE: Price information to be obtained from the given supplier.
CONF 002
(1) Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)

### Page 4

A340
SERVICE BULLETIN
SUMMARY
REV 00 Oct 12/20 A340-27-4214
Page 4
(a) T ask set A340-A-27-XX-4214-01000-93AA-A Modification to the Trimmable
Horizontal Stabilizer Actuator (THSA) by installation and activation of the
Electrical Load Sensing Device (ELSD)
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Aircraft standard tools See SB See Note Pin, pitch trim control
Components See SB See Note Bolt, lead, nut, screw, washer,
placard
Equipment See SB See Note ELSD
NOTE: Price information to be obtained from the given supplier.
CONF ALL
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
01V 06Y 14S 15R 17M 26L 31V 34N 36L 39N 41N 65W 68M 72T 82M 84W 90O 98W ABB
ABD AFR AIB ARG AXY BOE DGA DLH EDW F2I GAF HFM HFY IRC IRM KAC KMF LHT M3R MAU
MDG MRJ MSR PUE QQE ROI S3R SAA SAS SFB SWR SYR U6A VCV
G. CONCURRENT REQUIREMENTS
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
Service Bulletin(s) Modification(s)
Ref. SB A340-27-4213  
NOTE: Service Bulletin No. Ref. SB A340-27-4213 (FLIGHT CONTROLS - TRIMMABLE
HORIZONTAL STABILIZER (THS) HYDRAULIC ACTUATION - INTRODUCE WIRING
PROVISION FOR LOAD SENS).
H. NATURE OF THE WORK
CONF 001
(1) Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
(a) T ask set A340-A-27-XX-4214-01000-93AA-A Modification to the Trimmable
Horizontal Stabilizer Actuator (THSA) by installation and activation of the
Electrical Load Sensing Device (ELSD)
AIRCRAFT YES
EQUIPMENT YES
CONF 002
(1) Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
(a) T ask set A340-A-27-XX-4214-01000-93AA-A Modification to the Trimmable
Horizontal Stabilizer Actuator (THSA) by installation and activation of the
Electrical Load Sensing Device (ELSD)
AIRCRAFT YES

### Page 5

A340
SERVICE BULLETIN
SUMMARY
REV 00 Oct 12/20 A340-27-4214
Page 5
EQUIPMENT YES
CONF ALL
I. MANPOWER
CONF 001
(1) Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
(a) T ask set A340-A-27-XX-4214-01000-93AA-A Modification to the Trimmable
Horizontal Stabilizer Actuator (THSA) by installation and activation of the
Electrical Load Sensing Device (ELSD)
MANPOWER
TOTAL MAN-HOURS 2.25 h
ELAPSED TIME (HOURS) 2.00 h
CONF 002
(1) Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
(a) T ask set A340-A-27-XX-4214-01000-93AA-A Modification to the Trimmable
Horizontal Stabilizer Actuator (THSA) by installation and activation of the
Electrical Load Sensing Device (ELSD)
MANPOWER
TOTAL MAN-HOURS 2.25 h
ELAPSED TIME (HOURS) 2.00 h

### Page 6

A340
SERVICE BULLETIN
SUMMARY
Figure ICN-A340-A-27XX4214-A-FAPE3-01A78-A-001-01 SHEET 1/2
REV 00 Oct 12/20 A340-27-4214General overview
Page 6
CONF ALL
J. GENERAL OVERVIEW
CONF ALL
B
Z310
Z160
REMOVAL OF THE SAFETY CLIP FROM
CIRCUIT BREAKER 59CS
A
B
A
FR65
FR73
823
C
312AR
FR80
FR86
FR87
ICN-A340-A-27XX4214-A-FAPE3-01A78-A-001-01

### Page 7

A340
SERVICE BULLETIN
SUMMARY
Figure ICN-A340-A-27XX4214-A-FAPE3-01A79-A-001-01 SHEET 2/2
REV 00 Oct 12/20 A340-27-4214General overview
Page 7
CONF ALL
MODIFICATION OF THE
ELECTRICAL HARNESS 5869VB
MODIFICATION OF THE
ELECTRICAL HARNESS 5870VB
INSTALLATION OF ELECTRICAL
LOAD SENSING DEVICE (ELSD)
FR87
C
FR86
ICN-A340-A-27XX4214-A-FAPE3-01A79-A-001-01

### Page 8

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 8
ATA SYSTEM: 27
TITLE: FLIGHT CONTROLS - TRIMMABLE HORIZONTAL STABILIZER (THS)
HYDRAULIC ACTUATION - INSTALL ELSD ON THSA
1. PLANNING INFORMATION
A. APPLICABILITY
NOTE: These modifications are applicable by Service Bulletin only.
(1) Models
ON A/C 0026, 0031, 0063, 0074, 0075, 0080, 0081
340-211
ON A/C 0009, 0014, 0022, 0038, 0043, 0046, 0061, 0156, 0159, 0178
340-212
ON A/C 0004, 0151, 0204
340-213
ON A/C 0002, 0020, 0029, 0056, 0058, 0078, 0084, 0115
340-311
ON A/C 0041, 0044, 0047, 0051, 0076, 0079, 0091, 0094, 0367, 0374, 0381
340-312
ON A/C 0089, 0090, 0093, 0101, 0104, 0114, 0117, 0123, 0125, 0126, 0128, 0134, 0135,
0139, 0145, 0146, 0149, 0152, 0158, 0163, 0164, 0166, 0168, 0170, 0174, 0175, 0179,
0180, 0185, 0186, 0190, 0192-0194, 0197, 0199, 0201, 0202, 0207, 0208, 0210, 0212-0215,
0217, 0221, 0233, 0236, 0237, 0242, 0243, 0245, 0246, 0252, 0257, 0260, 0264, 0268,
0270, 0274, 0278, 0280, 0282, 0292, 0297, 0302, 0304, 0310, 0318, 0319, 0321, 0325,
0327, 0329, 0331, 0332, 0335, 0347, 0352, 0354, 0355, 0373, 0377-0379, 0385, 0387, 0390,
0395, 0399, 0402, 0406, 0411, 0413, 0415, 0424, 0430, 0433-0435, 0438, 0446, 0447, 0450,
0459, 0467, 0470, 0474, 0483, 0528, 0538, 0541, 0544-0546, 0554, 0556, 0559, 0561, 0562,
0582, 0585, 0590, 0598, 0643, 0646, 0651, 0668, 0793, 0800, 0835, 0844, 0921, 0938, 0955
340-313
CONF ALL
(2) Applicability by MSN
0002 0004 0009 0014 0020 0022 0026 0029 0031 0038 0041 0043 0044 0046 0047
0051 0056 0058 0061 0063 0074-0076 0078-0081 0084 0089-0091 0093 0094 0101
0104 0114 0115 0117 0123 0125 0126 0128 0134 0135 0139 0145 0146 0149 0151
0152 0156 0158 0159 0163 0164 0166 0168 0170 0174 0175 0178-0180 0185 0186
0190 0192-0194 0197 0199 0201 0202 0204 0207 0208 0210 0212-0215 0217 0221
0233 0236 0237 0242 0243 0245 0246 0252 0257 0260 0264 0268 0270 0274 0278
0280 0282 0292 0297 0302 0304 0310 0318 0319 0321 0325 0327 0329 0331 0332
0335 0347 0352 0354 0355 0367 0373 0374 0377-0379 0381 0385 0387 0390 0395
0399 0402 0406 0411 0413 0415 0424 0430 0433-0435 0438 0446 0447 0450 0459
0467 0470 0474 0483 0528 0538 0541 0544-0546 0554 0556 0559 0561 0562 0582
0585 0590 0598 0643 0646 0651 0668 0793 0800 0835 0844 0921 0938 0955
(3) MSN by configuration
CONF 001
MSN CONFIGURATION
0002 0020 0029 0041 0044 0047 0051 0056 0058 0076 0078
0079 0084 0089 0090 0091 0093 0094 0101 0104 0114 0115
0117 0123 0125 0126 0128 0134 0135 0139 0145 0146 0149
001

### Page 9

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 9
MSN CONFIGURATION
0152 0158 0163 0164 0166 0168 0170 0174 0175 0179 0180
0185 0186 0190 0192 0193 0194 0197 0199 0201 0202 0207
0208 0210 0212 0213 0214 0215 0217 0221 0233 0236 0237
0242 0243 0245 0246 0252 0257 0260 0264 0268 0270 0274
0278 0280 0282 0292 0297 0302 0304 0310 0318 0319 0321
0325 0327 0329 0331 0332 0335 0347 0352 0354 0355 0367
0373 0374 0377 0378 0379 0381 0385 0387 0390 0395 0399
0402 0406 0411 0413 0415 0424 0430 0433 0434 0435 0438
0446 0447 0450 0459 0467 0470 0474 0483 0528 0538 0541
0544 0545 0546 0554 0556 0559 0561 0562 0582 0585 0590
0598 0643 0646 0651 0668 0793 0800 0835 0844 0921 0938
0955
CONF 002
MSN CONFIGURATION
0004 0009 0014 0022 0026 0031 0038 0043 0046 0061 0063
0074 0075 0080 0081 0151 0156 0159 0178 0204
002
CONF ALL
(4) Configuration definition
CONF 001
Configuration 001
Config. 001 is valid for A340-300 aircraft.
CONF 001 retrofits following modifications: 205979S33745, 206264S33801.
CONF 002
Configuration 002
Config. 002 is valid for A340-200 aircraft.
CONF 002 retrofits following modifications: 205979S33745, 206264S33801.
CONF ALL
B. CONCURRENT REQUIREMENTS
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
Service Bulletin(s) Modification(s)
Ref. SB A340-27-4213  
NOTE: Service Bulletin No. Ref. SB A340-27-4213 (FLIGHT CONTROLS - TRIMMABLE
HORIZONTAL STABILIZER (THS) HYDRAULIC ACTUATION - INTRODUCE WIRING
PROVISION FOR LOAD SENS).
C. REASON
(1) History
The Trimmable Horizontal Stabilizer (THS) actuator has a fail-safe design: each
attachment, upper and lower, has two load paths, a normally loaded primary load
path and a secondary load path, which is only engaged in case of primary load path
rupture.

### Page 10

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 10
When the secondary load path is engaged, the design purpose was to generate a stall
of the unit by friction and to detect it by the position monitoring.
It has been demonstrated by test that the upper secondary load path may not stall
correctly in some cases.
(2) Objective/Action
Hence a new device has been developed, called Electrical Load Sensing Device (ELSD)
and manufactured by Collins Aerospace, which aims at detecting the engagement on
the secondary load path.
This Service Bulletin details instructions for installation and activation of the ELSD,
following the wiring provisions embodied.
(3) Advantages
Accomplishment of this Service Bulletin will allow to detect upper secondary load path
engagement. The periodic detailed inspection of THS actuator upper attachments for
secondary load path loading will be preserved.
(4) Operational/Maintenance Consequences
The Operational/Maintenance Consequences of this Service Bulletin are covered by
the update of the affected publications detailed in "PLANNING INFORMATION".
D. DESCRIPTION
T o accomplish this Service Bulletin it is necessary to:
(1) Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
(a) T ask set A340-A-27-XX-4214-01000-93AA-A Modification to the Trimmable
Horizontal Stabilizer Actuator (THSA) by installation and activation of the
Electrical Load Sensing Device (ELSD)
1 Remove the T wo Fail Safe Secondary Upper Bolts of the THSA FIN (1CS)
2 Install the ELSD FIN (58CS) on the THSA FIN (1CS)
3 Modify the Electrical Harness 5869VB and 5870VB
4 Modify the Circuit Breaker FIN (59CS) in the APU Control Box FIN (5000VE)
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
This Service Bulletin has been classified Mandatory by the issue of an Airworthiness
Directive (AD) published by the European Aviation Safety Agency (EASA). The AD must
be used as the reference document for the mandated accomplishment timescale.
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER

### Page 11

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 11
CONF 001
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
(a) T ask set A340-A-27-XX-4214-01000-93AA-A Modification to the Trimmable
Horizontal Stabilizer Actuator (THSA) by installation and activation of the
Electrical Load Sensing Device (ELSD)
PREPARATION
Job Set-Up 0.15 h
Open for Access Procedure 0.10 h
PROCEDURE
Remove the T wo Fail Safe Secondary Upper Bolts of the
THSA FIN (1CS)
0.25 h
Install the ELSD FIN (58CS) on the THSA FIN (1CS) 0.50 h
Modify the Electrical Harness 5869VB and 5870VB 0.25 h
Modify the Circuit Breaker FIN (59CS) in the APU Control
Box FIN (5000VE)
0.25 h
PREPARATION FOR TEST
PREPARATION FOR TEST 0.20 h
TEST
T est 0.30 h
CLOSE-UP
Close-up 0.25 h
TOTAL MAN-HOURS 2.25 h
ELAPSED TIME (HOURS) 2.00 h
CONF 002
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
(a) T ask set A340-A-27-XX-4214-01000-93AA-A Modification to the Trimmable
Horizontal Stabilizer Actuator (THSA) by installation and activation of the
Electrical Load Sensing Device (ELSD)
PREPARATION
Job Set-Up 0.15 h
Open for Access Procedure 0.10 h
PROCEDURE

### Page 12

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 12
Remove the T wo Fail Safe Secondary Upper Bolts of the
THSA FIN (1CS)
0.25 h
Install the ELSD FIN (58CS) on the THSA FIN (1CS) 0.50 h
Modify the Electrical Harness 5869VB and 5870VB 0.25 h
Modify the Circuit Breaker FIN (59CS) in the APU Control
Box FIN (5000VE)
0.25 h
PREPARATION FOR TEST
PREPARATION FOR TEST 0.20 h
TEST
T est 0.30 h
CLOSE-UP
Close-up 0.25 h
TOTAL MAN-HOURS 2.25 h
ELAPSED TIME (HOURS) 2.00 h
CONF ALL
H. WEIGHT AND BALANCE
CONF 001
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer's Empty Weight (MEW) and do not include operator's items. The definition of
MEW and operator's items is given in the Weight and Balance Manual (WBM), Ref. WBM.
Manufacturer's Empty Weight +1.745 kg (+3.847 lb)
Effect on Balance +103.046 kg.m (+745.332 lb.ft)
CONF 002
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer's Empty Weight (MEW) and do not include operator's items. The definition of
MEW and operator's items is given in the Weight and Balance Manual (WBM), Ref. WBM.
Manufacturer's Empty Weight +1.745 kg (+3.847 lb)
Effect on Balance +95.790 kg.m (+692.849 lb.ft)
CONF ALL
I. ELECTRICAL LOAD DATA
(1) Alternating Current (AC) Load Changes
Not changed
(2) Direct Current (DC) Load Changes
The values listed in the table(s) show the increase (+) or decrease (-) of the electrical
load resulting from the accomplishment of this Service Bulletin.
(a) Circuit Breaker Data
Busbar: FIN 309PP ATA/SubATA: 2744 Panel: Panel 5000VE
Circuit Breaker: FIN 59CS Existing
Designation: C/B ELSD
Nominal Power (Differential Value): +5W
Intermitted: NO Sheddable: NO Clipped: NO
Effect on electrical loads

### Page 13

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 13
Configuration Value (W) Operational Value (W) Max
Ground +5 +5
Start +5 +5
Roll +5 +5
T ake Off +5 +5
Climb +5 +5
Cruise +5 +5
Descent +5 +5
Landing +5 +5
T axi +5 +5
J. REFERENCES
CONCURRENT SERVICE BULLETIN (SB)
A340-27-4213
CONF 001
(1) Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
(a) T ask set A340-A-27-XX-4214-01000-93AA-A Modification to the Trimmable
Horizontal Stabilizer Actuator (THSA) by installation and activation of the
Electrical Load Sensing Device (ELSD)
AIRCRAFT MAINTENANCE MANUAL (AMM)
06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 T ask 11-00-00-400-801
T ask 11-00-00-400-803
T ask 12-34-24-860-802 T ask 20-16-00-912-801
T ask 20-21-11-911-801 T ask 20-21-15-912-801
T ask 20-28-00-912-810 24-00-00, Page Block 001
T ask 24-41-00-861-801
T ask 24-41-00-862-801
T ask 25-54-00-000-801
T ask 25-54-00-400-801
T ask 27-40-00-866-801 T ask 27-44-00-710-805
T ask 27-44-51-710-802 T ask 29-00-00-863-802
T ask 29-00-00-863-803
T ask 29-00-00-864-802
T ask 29-00-00-864-803
T ask 29-00-00-864-804
T ask 31-18-00-010-801 T ask 31-60-00-860-801
T ask 31-60-00-860-802
T ask 52-30-00-010-803
T ask 52-30-00-410-803
ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)
20-51-20 20-52-10

### Page 14

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 14
ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)
20-54-50 20-55-00
STRUCTURAL REPAIR MANUAL (SRM)
51-24-00 51-42-00
51-43-00
TECHNICAL FOLLOW UP (TFU)
27.44.00.022
WEIGHT AND BALANCE MANUAL (WBM)
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
CONF 002
(1) Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
(a) T ask set A340-A-27-XX-4214-01000-93AA-A Modification to the Trimmable
Horizontal Stabilizer Actuator (THSA) by installation and activation of the
Electrical Load Sensing Device (ELSD)
AIRCRAFT MAINTENANCE MANUAL (AMM)
06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 T ask 11-00-00-400-801
T ask 11-00-00-400-803
T ask 12-34-24-860-802 T ask 20-16-00-912-801
T ask 20-21-11-911-801 T ask 20-21-15-912-801
T ask 20-28-00-912-810 24-00-00, Page Block 001
T ask 24-41-00-861-801
T ask 24-41-00-862-801
T ask 25-54-00-000-801
T ask 25-54-00-400-801
T ask 27-40-00-866-801 T ask 27-44-00-710-805
T ask 27-44-51-710-802 T ask 29-00-00-863-802
T ask 29-00-00-863-803
T ask 29-00-00-864-802
T ask 29-00-00-864-803
T ask 29-00-00-864-804
T ask 31-18-00-010-801 T ask 31-60-00-860-801
T ask 31-60-00-860-802
T ask 52-30-00-010-803
T ask 52-30-00-410-803
ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)
20-51-20 20-52-10
20-54-50 20-55-00

### Page 15

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 15
STRUCTURAL REPAIR MANUAL (SRM)
51-24-00 51-42-00
51-43-00
TECHNICAL FOLLOW UP (TFU)
27.44.00.022
WEIGHT AND BALANCE MANUAL (WBM)
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
CONF ALL
K. PUBLICATION AFFECTED
AIRCRAFT MAINTENANCE MANUAL (AMM)
AIRCRAFT SCHEMATIC MANUAL (ASM)
AIRCRAFT WIRING LIST (AWL)
AIRCRAFT WIRING MANUAL (AWM)
ILLUSTRATED PARTS CATALOG (IPC)
MASTER MINIMUM EQUIPMENT LIST (MMEL)
TROUBLE SHOOTING MANUAL (TSM)
L. INDUSTRY SUPPORT INFORMATION
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department: monitored.retrofit@airbus.com.
Industry support terms for the equipment must be negotiated with the equipment supplier.

### Page 16

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 16
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
CONF 001
Material for task set A340-A-27-XX-4214-01000-93AA-A Modification to the
Trimmable Horizontal Stabilizer Actuator (THSA) by installation and activation of
the Electrical Load Sensing Device (ELSD)
MATERIAL QTY SEE NOTES
Aircraft standard tools See SB
Consumables See SB
Referenced consumables See SB
Components See SB
Equipment See SB
CONF 002
Material for task set A340-A-27-XX-4214-01000-93AA-A Modification to the
Trimmable Horizontal Stabilizer Actuator (THSA) by installation and activation of
the Electrical Load Sensing Device (ELSD)
MATERIAL QTY SEE NOTES
Aircraft standard tools See SB
Consumables See SB
Referenced consumables See SB
Components See SB
Equipment See SB
CONF ALL
B. TOOLING
CONF 001
Aircraft standard tools for task set A340-A-27-XX-4214-01000-93AA-A
Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
Procurement address D4296
AIRBUS Material, Logistics and Suppliers
Customer Order Fulfilment
Weg beim Jaeger 150
D–22335 HAMBURG
GERMANY
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
0U191067 (D4296) 1 PIN (1)
98F27401000000
(D4296) 1 PITCHTRC (1)

### Page 17

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 17
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
98L12003001000
(D4296) 1 HARNESS (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
CONF 002
Aircraft standard tools for task set A340-A-27-XX-4214-01000-93AA-A
Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
Procurement address D4296
AIRBUS Material, Logistics and Suppliers
Customer Order Fulfilment
Weg beim Jaeger 150
D–22335 HAMBURG
GERMANY
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
0U191067 (D4296) 1 PIN (1)
98F27401000000
(D4296) 1 PITCHTRC (1)
98L12003001000
(D4296) 1 HARNESS (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
CONF ALL
C. CONSUMABLES
CONF 001
Consumables for task set A340-A-27-XX-4214-01000-93AA-A Modification to the
Trimmable Horizontal Stabilizer Actuator (THSA) by installation and activation of
the Electrical Load Sensing Device (ELSD)
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
04TMB2 Varnish - - ElectricalBonding Structure
04TMM9 Varnish - - - StructureLegacy
05EML8 Epoxy Adhesive - - - Legacy2

### Page 18

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 18
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
06ACC1
Polysulfide Sealant - Low
Density MultiPurpose
Interfay
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
CONF 002
Consumables for task set A340-A-27-XX-4214-01000-93AA-A Modification to the
Trimmable Horizontal Stabilizer Actuator (THSA) by installation and activation of
the Electrical Load Sensing Device (ELSD)
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
04TMB2 Varnish - - ElectricalBonding Structure
04TMM9 Varnish - - - StructureLegacy
05EML8 Epoxy Adhesive - - - Legacy2
06ACC1
Polysulfide Sealant - Low
Density MultiPurpose
Interfay
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
CONF 001
Referenced consumables for task set A340-A-27-XX-4214-01000-93AA-A
Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
T o accomplish this Service Bulletin it is necessary to use the consumable materials listed in
the subsequent referenced tasks.
Ref. AMM T ask 11-00-00-400-803
Ref. AMM T ask 11-00-00-400-801
Ref. AMM T ask 20-21-15-912-801
Ref. AMM T ask 20-28-00-912-810
Ref. AMM T ask 25-54-00-400-801
CONF 002
Referenced consumables for task set A340-A-27-XX-4214-01000-93AA-A
Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by
installation and activation of the Electrical Load Sensing Device (ELSD)
T o accomplish this Service Bulletin it is necessary to use the consumable materials listed in
the subsequent referenced tasks.
Ref. AMM T ask 11-00-00-400-803
Ref. AMM T ask 11-00-00-400-801
Ref. AMM T ask 20-21-15-912-801

### Page 19

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 19
Ref. AMM T ask 20-28-00-912-810
Ref. AMM T ask 25-54-00-400-801
CONF ALL
D. LIST OF NEW PARTS
CONF 001
Components for task set A340-A-27-XX-4214-01000-93AA-A Modification to the
Trimmable Horizontal Stabilizer Actuator (THSA) by installation and activation of
the Electrical Load Sensing Device (ELSD)
Procurement address D4296
AIRBUS Material, Logistics and Suppliers
Customer Oreder Fulfilment,
Weg beim Jaeger 150
D–22335 HAMBURG
GERMANY
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 E0090-41-200NN(D4296) 1 LEAD (1)
11 NAS1149C0463R(D4296) 1 WASHER (1)
12 NSA5355-4CA(D4296) 1 WASHER (1)
13 NAS1801-4-7(D4296) 1 SCREW (1)
14 NAS1303-2 (D4296) 1 BOLT (1)
15 NAS1149C0332R(D4296) 1 WASHER (1)
16 NAS1726-3E (D4296) 1 NUT (1)
22 F2707006622600(D4296) 1 PLACARD (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
CONF 002
Components for task set A340-A-27-XX-4214-01000-93AA-A Modification to the
Trimmable Horizontal Stabilizer Actuator (THSA) by installation and activation of
the Electrical Load Sensing Device (ELSD)
Procurement address D4296 AIRBUS Material, Logistics and Suppliers

### Page 20

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 20
Customer Oreder Fulfilment,
Weg beim Jaeger 150
D–22335 HAMBURG
GERMANY
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 E0090-41-200NN(D4296) 1 LEAD (1)
11 NAS1149C0463R(D4296) 1 WASHER (1)
12 NSA5355-4CA(D4296) 1 WASHER (1)
13 NAS1801-4-7(D4296) 1 SCREW (1)
14 NAS1303-2 (D4296) 1 BOLT (1)
15 NAS1149C0332R(D4296) 1 WASHER (1)
16 NAS1726-3E (D4296) 1 NUT (1)
22 F2707006622600(D4296) 1 PLACARD (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
CONF 001
Equipment for task set A340-A-27-XX-4214-01000-93AA-A Modification to the
Trimmable Horizontal Stabilizer Actuator (THSA) by installation and activation of
the Electrical Load Sensing Device (ELSD)
Procurement address 23154
GOODRICH ACTUATION SYSTEMS SAS
13 AVENUE DE L'EGUILLETTE
95310 SAINT OUEN L’AUMONE
FRANCE
Phone: +33 1 34 32 63 00
NOTE(S)
Vendor parts are to be procured from the address given above.

### Page 21

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 21
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
6 MA5115 (23154) 1 DEVICE (1) (2)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): Procurement terms for the equipment must be negotiated with the equipment
supplier.
CONF 002
Equipment for task set A340-A-27-XX-4214-01000-93AA-A Modification to the
Trimmable Horizontal Stabilizer Actuator (THSA) by installation and activation of
the Electrical Load Sensing Device (ELSD)
Procurement address 23154
GOODRICH ACTUATION SYSTEMS SAS
13 AVENUE DE L'EGUILLETTE
95310 SAINT OUEN L’AUMONE
FRANCE
Phone: +33 1 34 32 63 00
NOTE(S)
Vendor parts are to be procured from the address given above.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
6 MA5115 (23154) 1 DEVICE (1) (2)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): Procurement terms for the equipment must be negotiated with the equipment
supplier.
CONF ALL
E. LIST OF EXISTING PARTS
No parts

### Page 22

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 22
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A340-A-27-XX-4214-01000-93AA-A (A340-A-27-XX-4214-01ZZZ-93AZ-A)
Modification to the Trimmable Horizontal Stabilizer Actuator (THSA) by installation and activation
of the Electrical Load Sensing Device (ELSD)
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESPM Ref. ESPM 20-55-00.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including RC paragraph contained herein, contact
AIRBUS for further instructions and approval.
NOTE: Discarded parts must be managed at the operator's discretion.
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
CONF 001
TOTAL MAN-HOURS 2.25 h

### Page 23

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 23
CONF 002
TOTAL MAN-HOURS 2.25 h
CONF 001
ELAPSED TIME (HOURS) 2.00 h
CONF 002
ELAPSED TIME (HOURS) 2.00 h
CONF ALL
B. PREPARATION
(1) Task A340-A-27-XX-4214-01001-540A-A (A340-A-27-XX-4214-01ZZZ-540Z-A)
Job Set-Up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.15 h
Minimum Number of person 1
Elapsed Time 0.15 h
Material necessary to do the job
Aircraft standard tools
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
98F27401000000 1 PITCHTRC (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information
Manuals/Drawings References/Sheets
AMM
T ask 12-34-24-860-802
T ask 24-41-00-861-801
T ask 27-40-00-866-801
T ask 29-00-00-864-804
Procedure
NOTE: For the basic Aircraft configuration, refer to AMM Chapter “Introduction -
Aircraft status for maintenance" in Manual Front Matter section.
WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS
ARE CLEAR.
MOVEMENT OF THE FLIGHT CONTROLS CAN CAUSE INJURY TO
PERSONS AND/OR DAMAGE.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM T ask 12-34-
24-860-802.
(b) Energize the aircraft electrical circuits, refer to Ref. AMM T ask 24-41-00-861-801.
(c) In the cockpit, on the panel Panel 125VU, make sure that the pitch-trim control
wheels are in the "0" position, refer to Ref. AMM T ask 27-40-00-866-801.
(d) Install the pitch trim control on the pitch-trim control wheels:
1 PITCH TRIM CONTROL 98F27401000000

### Page 24

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 24
(e) Make sure that the hydraulic systems are depressurized and put them in the
maintenance configuration, refer to Ref. AMM T ask 29-00-00-864-804.
(f) Put the warning notices in position, in the cockpit, to tell persons:
- Not to operate the pitch controls
- Not to pressurize the blue and yellow hydraulic systems.
(g) Open, safety and tag these circuit breakers:
PANEL DESIGNATION FIN LOCATION SEE NOTES
FCPC3 STBY COM 7CE6 (1) (2)
FCPC3 STBY MON 7CE5 (1) (2)
FCDC 2 6CE2 (1) (2)
FCSC 2 10CE2 (1) (2)
THS ACTR MOT 3 5CS3 (1) (2)
THS ACTR MOT2 NORM 5CS2 (1) (2)
FCPC 3 7CE3 (1) (2)
FCPC 2 NORM 7CE2 (1) (2)
FCPC 3 7CE4 (1) (2)
FCSC 1 NORM 10CE1 (1) (2)
FCPC 1 NORM 7CE1 (1) (2)
FCDC 1 6CE1 (1) (2)
FCSC 1 STBY 9CE (1) (2)
FCPC 1 STBY 11CE (1) (2)
THS ACTR MOT 1 5CS1 (1) (2)
THS ACTR MOT2 STBY 34CS (1) (2)
FCPC 2 STBY 28CE (1) (2)
NOTE(S)
(1): For circuit breaker safety practices, refer to Ref. AMM T ask 20-16-00-912-801.
(2): For the circuit breaker location, refer to Ref. AMM 24-00-00, Page Block 001.
(2) Task A340-A-27-XX-4214-02001-540A-A (A340-A-27-XX-4214-02ZZZ-540Z-A)
Open for Access Procedure
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
162
310
Manpower/Resources/Skills
Man-hours 0.10 h
Minimum Number of person 1
Elapsed Time 0.10 h

### Page 25

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 25
Material necessary to do the job
Aircraft standard tools
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
0U191067 1 PIN (1)
98L12003001000 1 HARNESS (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information
Manuals/Drawings References/Sheets
AMM T ask 25-54-00-000-801T ask 52-30-00-010-803
Procedure
(a) Put on a safety harness:
WARNING: BEFORE YOU START WORK, YOU MUST PUT ON A SAFETY
HARNESS AND ATTACH IT TO THE ACCESS PLATFORM.
WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL
YOU OR CAUSE YOU INJURY.
1 Put on and attach the HARNESS, before you start work in the work area.
1 HARNESS,SAFETY 98L12003001000  
(b) Open the bulk cargo-compartment Door 823, refer to Ref. AMM T ask 52-30-00-
010-803.
(c) On the Panel 5026VE, make sure that the cargo compartment light switch is set
to the "ON" position, refer to Ref. Fig. Location of equipment.
(d) Remove the sidewall Panel 162RW and Panel 162KW, refer to Ref. AMM T ask 25-
54-00-000-801.
(e) Put an access platform in position, below the access Door 312AR.
(f) Open and safety the access Door 312AR.
(g) Make sure that tumbler switch FIN 4LJ is set to the "ON" position, refer to Ref. Fig.
Location of equipment.
(h) Install the mechanical input-rigging pin in the mechanical input of the THS
actuator:
1 MECHANICAL INPUT-
RIGGING PIN
0U191067

### Page 26

A340
SERVICE BULLETIN
Figure ICN-A340-A-27XX4214-A-FAPE3-01ACR-A-001-01 SHEET 1/2
REV 00 Oct 12/20 A340-27-4214Location of equipment
Page 26
CONF ALL
C
Z310
Z160
A 823
FR65
FR73
A
B
5026VE
B
ICN-A340-A-27XX4214-A-FAPE3-01ACR-A-001-01

### Page 27

A340
SERVICE BULLETIN
Figure ICN-A340-A-27XX4214-A-FAPE3-01ACS-A-001-01 SHEET 2/2
REV 00 Oct 12/20 A340-27-4214Location of equipment
Page 27
CONF ALL
4LJ
TUMBLER SWITCH
D
OFF
ON
FR82
FR86
FR85
FR84
FR83
312AR
C
D
ICN-A340-A-27XX4214-A-FAPE3-01ACS-A-001-01

### Page 28

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 28
C. PROCEDURE
(1) Task A340-A-27-XX-4214-01001-920A-A (A340-A-27-XX-4214-01ZZZ-920Z-A)
Remove the Two Fail Safe Secondary Upper Bolts of the THSA FIN (1CS)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Door 312AR310
Work location From Frame 86 to Frame 87
Manpower/Resources/Skills
Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Referenced Information
Manuals/Drawings References/Sheets
AMM
06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
SRM 51-42-0051-43-00
Procedure
(a) Standard Practices:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
5 T ag all the parts you must remove and retain to make the subsequent
installation easier.
6 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
7 Get alternative and substitute fastener data in accordance with Ref. SRM
51-43-00.
(b) Remove the two upper bolts of the THS actuator, as shown on Ref. Fig. Removal
of the T wo Fail Safe Secondary Upper Bolts of the THSA, view B:
1 Remove:
2 Pin-Cotter   Item (1) Discard
2 Nut   Item (2) Discard
2 BUSHING   Item (3) Discard
2 BOLT   Item (4) Discard

### Page 29

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 29
NOTE: The two bushing item (5) are not removed, they must be kept in
position.

### Page 30

A340
SERVICE BULLETIN
Figure ICN-A340-A-27XX4214-A-FAPE3-01A73-A-001-01 SHEET 1/2
REV 00 Oct 12/20 A340-27-4214Removal of the T wo Fail Safe
Secondary Upper Bolts of the THSA Page 30
CONF ALL
B
A
FR87
FR86
FR87
FR80
FR86
Z310
A
312AR
ICN-A340-A-27XX4214-A-FAPE3-01A73-A-001-01

### Page 31

A340
SERVICE BULLETIN
Figure ICN-A340-A-27XX4214-A-FAPE3-01A74-A-001-01 SHEET 2/2
REV 00 Oct 12/20 A340-27-4214Removal of the T wo Fail Safe
Secondary Upper Bolts of the THSA Page 31
CONF ALL
(2)
(3)
(1)
(4)
(5)
B
ICN-A340-A-27XX4214-A-FAPE3-01A74-A-001-01

### Page 32

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 32
(2) Task A340-A-27-XX-4214-02001-920A-A (A340-A-27-XX-4214-02ZZZ-920Z-A)
Install the ELSD FIN (58CS) on the THSA FIN (1CS)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Door 312AR310
Work location From Frame 86 to Frame 87
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
04TMB2 Varnish - - ElectricalBonding Structure
04TMM9 Varnish - - - StructureLegacy
05EML8 Epoxy Adhesive - - - Legacy2
06ACC1
Polysulfide Sealant - Low
Density MultiPurpose
Interfay
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 E0090-41-200NN 1 LEAD
11 NAS1149C0463R 1 WASHER
12 NSA5355-4CA 1 WASHER
13 NAS1801-4-7 1 SCREW
14 NAS1303-2 1 BOLT
15 NAS1149C0332R 1 WASHER
16 NAS1726-3E 1 NUT
22 F2707006622600 1 PLACARD
Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
6 MA5115 1 DEVICE (1)
NOTE(S)
(1): Procurement terms for the equipment must be negotiated with the equipment
supplier.

### Page 33

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 33
Referenced Information
Manuals/Drawings References/Sheets
AMM
06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
T ask 11-00-00-400-801
T ask 11-00-00-400-803
T ask 20-21-11-911-801
T ask 20-21-15-912-801
T ask 20-28-00-912-810
CML CONSUMABLE MATERIAL LIST (CML)
ESPM 20-51-20
SRM
51-24-00
51-42-00
51-43-00
Procedure
(a) Standard Practices:
1 For the specification of Material application codes given in this Service
Bulletin, refer to the Ref. CML.
2 For the FR identification, refer to Ref. AMM 06-31-53, Page Block 001.
3 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
4 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
5 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
6 T o torque tighten the electrical component fasteners, refer to Ref. AMM
T ask 20-21-15-912-801.
7 T o torque tighten the standard threaded fasteners, refer to Ref. AMM T ask
20-21-11-911-801.
8 Apply sealant in accordance with Ref. SRM 51-24-00.
9 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM T ask
20-28-00-912-810.
10 Get alternative and substitute fastener data in accordance with Ref. SRM
51-43-00.
11 For the installation of placards, refer to Ref. AMM T ask 11-00-00-400-801.
(b) Install the ELSD on the THS Actuator, as shown on Ref. Fig. Installation of the
ELSD on the THSA, view B:
1 Clean the bushes, item (5) with:
  T extile - Lint free Cotton14SBA1  
and
  Non Aqueous Cleaner -
General
08BAA9  
2 Install:
FIN 58CS

### Page 34

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 34
1 DEVICE-LOAD SENSING
DEVICE
MA5115 Item 6
NOTE: The spring boxes, item 7, the new locking washer, item 8 and the
nut, item 9 are integral parts of the ELSD, item 6.
3 T orque the nuts, item 9 between 0.4 m.daN (35.40 lbf.in) and 0.5 m.daN
(44.25 lbf.in).
4 Bend two teeth of locking washer, item 8, on each side of the nut, item 9,
refer to Ref. Fig. Installation of the ELSD on the THSA view C and view D.
(c) Install the bonding strap on the ELSD, as shown on Ref. Fig. Installation of the
ELSD on the THSA, view B.
1 Before installation, bend the tab washer, item 12, on the ELSD side, item 6.
2 Put in position:
1 LEAD-BONDING,ROUND E0090-41-200NN Item 10
3 Attach the lead bonding, item 10, with:
1 WASHER-LOCK NSA5355-4CA Item 12
1 WASHER NAS1149C0463R Item 11
1 SCREW NAS1801-4-7 Item 13
1 BOLT NAS1303-2 Item 14
1 WASHER NAS1149C0332R Item 15
1 NUT NAS1726-3E Item 16
4 T orque the screw, item 13, between 0.82 m.daN (72.57 lbf.in) and 1.6
m.daN (93.81 lbf.in).
5 After installation, bend the tab washer, item 12, on the screw side, item 13.
6 T orque the screw, item 14 and nut, item 16 between 0.37 m.daN (32.74
lbf.in) and 0.48 m.daN (42.48 lbf.in).
7 Do the electrical bonding between the FIN 58CS and lead bonding item 10
and between the item 10 and the bracket, refer to Ref. AMM T ask 20-28-00-
912-810.
8 Apply, to the head of the screws, the item 13 and 14 and nut, item 16,
with:
  Polysulfide Sealant
- Low Density
MultiPurpose Interfay
06ACC1  
and
  Varnish - - Electrical
Bonding Structure
04TMB2  
(d) Install the placard as shown on, Ref. Fig. Installation of the ELSD on the THSA,
view A:
Refer to Ref. AMM T ask 11-00-00-400-803.
1 Install:
1 PLACARD F2707006622600 Item 22

### Page 35

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 35
with:
  Epoxy Adhesive - - -
Legacy 2
05EML8  
2 Protect the placard, item 22, with:
  Varnish - - - Structure
Legacy
04TMM9

### Page 36

A340
SERVICE BULLETIN
Figure ICN-A340-A-27XX4214-A-FAPE3-01A75-A-002-01 SHEET 1/3
REV 00 Oct 12/20 A340-27-4214Installation of the ELSD on the THSA
Page 36
CONF ALL
1CSACTUATOR-
THS
BOND THE PLACARD WITH MATERIAL No 05EML801
PROTECT WITH MATERIAL No 04TMM902
NOTE:
FR86
FR87
B
A
FR87
FR80
FR86
Z310
A
312AR
01 02 22
58CS ELSD
C D
ICN-A340-A-27XX4214-A-FAPE3-01A75-A-002-01

### Page 37

A340
SERVICE BULLETIN
Figure ICN-A340-A-27XX4214-A-FAPE3-01A76-A-002-01 SHEET 2/3
REV 00 Oct 12/20 A340-27-4214Installation of the ELSD on the THSA
Page 37
CONF ALL
13
12
11 10
(5)
16
15
14
NOTE:
ELECTRICAL BONDING
6
58CS
B
06
0706
04
0705
AFTER INSTALLATION, PAINT THE HEAD OF THE SCREW WITH MATERIAL No 06ACC1 AND 04TMB2
TORQUE THE SCREW BETWEEN 0.82 m.daN (72.57 lbf.in) AND 1.6 m.daN (93.81 lbf.in)
TORQUE THE NUT BETWEEN 0.4 m.daN (35.40 lbf.in) AND 0.5 m.daN (44.25 lbf.in)
BEFORE INSTALLATION, BEND THE WASHER TAB, ITEM 12, ON THE EQUIPMENT SIDE
AND AFTER INSTALLATION, BEND IT ON THE SCREW SIDE
TORQUE THE SCREW AND NUT BETWEEN 0.37 m.daN (32.74 lbf.in) AND 0.48 m.daN (42.48 lbf.in)
03
06
05
04
07
AFTER INSTALLATION, PAINT THE NUT WITH MATERIAL No 06ACC1 AND 04TMB208
08
9 8
7
03
ICN-A340-A-27XX4214-A-FAPE3-01A76-A-002-01

### Page 38

A340
SERVICE BULLETIN
Figure ICN-A340-A-27XX4214-A-FAPE3-01AIC-A-001-01 SHEET 3/3
REV 00 Oct 12/20 A340-27-4214Installation of the ELSD on the THSA
Page 38
CONF ALL
C
D
VIEW LOOKING AFT
VIEW LOOKING AFT
THE NUTS ANGULAR POSITION SHALL BE VISUALLY INSPECTED IN ORDER TO DETERMINE THE
TWO EDGES OF EACH NUT THAT ARE LOCATED BETWEEN TWO CONSECUTIVE TEETH OF
THE LOCKING WASHER
09
THE TEETH OF THE LOCKING WASHER LOCATED AROUND THOSE EDGES HAVE10
TO BE BEND UP TO CONTACT WITH THE NUTS FACES
10
09
LOCKING WASHER OPEN CONDITION
LOCKING WASHER CLOSED CONDITION
THE  ARROWS INDICATES THOSE EDGES THAT HAVE TO BE DETECTED. IN ANY
 ANGULAR CONFIGURATION, A MINIMUM OF TWO EDGES WILL BE LOCATED
 BETWEEN TWO TEETH
NOTE:
ICN-A340-A-27XX4214-A-FAPE3-01AIC-A-001-01

### Page 39

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 39
(3) Task A340-A-27-XX-4214-03001-920A-A (A340-A-27-XX-4214-03ZZZ-920Z-A)
Modify the Electrical Harness 5869VB and 5870VB
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Door 312AR310
Work location From Frame 85 to Frame 87
Manpower/Resources/Skills
Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Skills Electrical
Referenced Information
Manuals/Drawings References/Sheets
AMM
06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
T ask 20-28-00-912-810
ESPM
20-51-20
20-52-10
20-54-50
Procedure
(a) Standard Practices:
1 For the FR identification, refer to Ref. AMM 06-31-53, Page Block 001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
5 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
6 T ag all the parts you must remove and retain to make the subsequent
installation easier.
7 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
8 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM T ask
20-28-00-912-810.
(b) Modify the routing of electrical harness FIN 5869VB and FIN 5870VB.
1 Remove, as shown on Ref. Fig. Modification to the Electrical Harness
5869VB and 5870VB, view B:
1 Blanking cap   Item (20) Discard
1 Blanking cap   Item (21) Discard

### Page 40

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 40
FIN 5869VB
1 HARNESS-
CABLE,5869VB
F9297186900000 Item (17) Retain
FIN 5870VB
1 HARNESS-
CABLE,5870VB
F9297187000000 Item (18) Retain
1 Cap-Protective   Item (19) Retain
2 Install, as shown on Ref. Fig. Modification to the Electrical Harness 5869VB
and 5870VB, view C:
FIN 5869VB
1 HARNESS-
CABLE,5869VB
F9297186900000 Item (17) Retained
FIN 5870VB
1 HARNESS-
CABLE,5870VB
F9297187000000 Item (18) Retained
1 Cap-Protective   Item (19) Retained

### Page 41

A340
SERVICE BULLETIN
Figure ICN-A340-A-27XX4214-A-FAPE3-01A7A-A-001-01 SHEET 1/3
REV 00 Oct 12/20 A340-27-4214Modification to the Electrical Harness 5869VB and 5870VB
Page 41
CONF ALL
FR87
A
B C
FR86
FR87
FR80
FR86
Z310
A
312AR
ICN-A340-A-27XX4214-A-FAPE3-01A7A-A-001-01

### Page 42

A340
SERVICE BULLETIN
Figure ICN-A340-A-27XX4214-A-FAPE3-01A7B-A-001-01 SHEET 2/3
REV 00 Oct 12/20 A340-27-4214Modification to the Electrical Harness 5869VB and 5870VB
Page 42
CONF ALL
BEFORE
(21)
(20)
58CSS
(19)
5869VB /1MF
5870VB /2MF
58CSR
(17)
(18)
B
ICN-A340-A-27XX4214-A-FAPE3-01A7B-A-001-01

### Page 43

A340
SERVICE BULLETIN
Figure ICN-A340-A-27XX4214-A-FAPE3-01A7C-A-001-01 SHEET 3/3
REV 00 Oct 12/20 A340-27-4214Modification to the Electrical Harness 5869VB and 5870VB
Page 43
CONF ALL
AFTER
58CSS
58CSR
(19)
5870VB /2MF
(18)
5869VB /1MF
(17)
C
ICN-A340-A-27XX4214-A-FAPE3-01A7C-A-001-01

### Page 44

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 44
(4) Task A340-A-27-XX-4214-04001-920A-A (A340-A-27-XX-4214-04ZZZ-920Z-A)
Modify the Circuit Breaker FIN (59CS) in the APU Control Box FIN (5000VE)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Door 823Panel 162KW, Panel 162RW160
Work location From Frame 65 to Frame 73
Manpower/Resources/Skills
Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Skills Electrical
Referenced Information
Manuals/Drawings References/Sheets
AMM
06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
T ask 20-16-00-912-801
24-00-00, Page Block 001
Procedure
(a) Standard Practices:
1 For the FR identification, refer to Ref. AMM 06-31-53, Page Block 001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 For the circuit breaker location, refer to Ref. AMM 24-00-00, Page Block
001.
5 For circuit breaker safety practices, refer to Ref. AMM T ask 20-16-00-912-
801.
(b) Remove the lock wire, safety clip and close the circuit breaker FIN 59CS as
shown on Ref. Fig. Modification to the Equipment in the APU Control Box 5000VE.
1 Clip-Locking   Item (23) Discard

### Page 45

A340
SERVICE BULLETIN
Figure ICN-A340-A-27XX4214-A-FAPE3-01A77-A-001-01 SHEET 1/1
REV 00 Oct 12/20 A340-27-4214Modification to the Equipment in the APU Control Box 5000VE
Page 45
CONF ALL
01
FR73
FR65
Z160
A
5000VE
B
59CS
B
NOTE:
REMOVE AND DISCARD THE LOCKWIRE01
823
(23)
ELSD
CTL
A
ICN-A340-A-27XX4214-A-FAPE3-01A77-A-001-01

### Page 46

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 46
D. PREPARATION FOR TEST
(1) Task A340-A-27-XX-4214-02001-390A-A (A340-A-27-XX-4214-02ZZZ-390Z-A)
PREPARATION FOR TEST
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.20 h
Minimum Number of person 2
Elapsed Time 0.10 h
Procedure
(a) Job Set-Up:
1 Remove the safety clips and tags and close these circuit breakers:
PANEL DESIGNATION FIN LOCATION SEE NOTES
FCPC3 STBY COM 7CE6 (1) (2)
FCPC3 STBY MON 7CE5 (1) (2)
FCDC 2 6CE2 (1) (2)
FCSC 2 10CE2 (1) (2)
THS ACTR MOT 3 5CS3 (1) (2)
THS ACTR MOT2 NORM 5CS2 (1) (2)
FCPC 3 7CE3 (1) (2)
FCPC 2 NORM 7CE2 (1) (2)
FCPC 3 7CE4 (1) (2)
FCSC 1 NORM 10CE1 (1) (2)
FCPC 1 NORM 7CE1 (1) (2)
FCDC 1 6CE1 (1) (2)
FCSC 1 STBY 9CE (1) (2)
FCPC 1 STBY 11CE (1) (2)
THS ACTR MOT 1 5CS1 (1) (2)
ELSD 59CS (1) (2)
THS ACTR MOT2 STBY 34CS (1) (2)
FCPC 2 STBY 28CE (1) (2)
NOTE(S)
(1): For circuit breaker safety practices, refer to Ref. AMM T ask 20-16-00-912-801.
(2): For the circuit breaker location, refer to Ref. AMM 24-00-00, Page Block 001.
2 Remove the pitch trim control P/N 98F27401000000 from the pitch-trim
control wheel in the cockpit.
3 Remove the mechanical input-rigging pin P/N 0U191067 from the
mechanical input of the THS actuator.
E. TEST
(1) Task A340-A-27-XX-4214-01001-390A-A (A340-A-27-XX-4214-01ZZZ-390Z-A)
Test

### Page 47

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 47
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.30 h
Minimum Number of person 2
Elapsed Time 0.15 h
Referenced Information
Manuals/Drawings References/Sheets
AMM
T ask 27-44-00-710-805
T ask 27-44-51-710-802
T ask 29-00-00-863-802
T ask 29-00-00-863-803
T ask 29-00-00-864-802
T ask 29-00-00-864-803
T ask 31-18-00-010-801
T ask 31-60-00-860-801
T ask 31-60-00-860-802
Procedure
(a) Do the Operational Check of THSA Load Sensing Device, refer to Ref. AMM T ask
27-44-51-710-802.
NOTE: If the Ref. AMM T ask 27-44-51-710-802 is not available in the latest AMM
operator’s issue, do these steps.
WARNING: MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING
NOTICES ARE IN POSITION BEFORE YOU START A TASK ON
OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO
PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT
CONTROL SURFACES ARE CLEAR BEFORE YOU PRESSURIZE/
DEPRESSURIZE A HYDRAULIC SYSTEM. MOVEMENT OF THE
FLIGHT CONTROL SURFACES CAN BE DANGEROUS AND/OR
CAUSE DAMAGE.
1 Job Set-up:
a Aircraft Maintenance Configuration.
<1> Do the Electronic Instrument System (EIS) start procedure (only
EWD and SD), refer to Ref. AMM T ask 31-60-00-860-801.
<2> On the FLT CTL section of the overhead Panel 241VU, make sure
that the PRIM 1 and SEC 1 pushbutton switches are pushed (the
OFF and FAULT legends of these pushbutton switches are off).
<3> On the FLT CTL section of the overhead Panel 212VU, make
sure that the PRIM 2, PRIM 3 and SEC 2 pushbutton switches
are pushed (the OFF and FAULT legends of these pushbutton
switches are off).

### Page 48

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 48
<4> Pressurize the Blue and Yellow hydraulic systems, refer to Ref.
AMM T ask 29-00-00-863-802 and Ref. AMM T ask 29-00-00-863-
803.
<5> On the HYD section of the maintenance Panel 285VU, make
sure that the LEAK MEASUREMENT VALVES/B and the LEAK
MEASUREMENT VALVES/Y pushbutton switches are pushed (the
OFF legends of these pushbutton switches are off).
<6> Put the WARNING NOTICE(S) in position to tell persons that the
trimmable horizontal stabilizer is in operation.
<7> Put the WARNING NOTICE(S) in the cockpit to tell persons not to
operate the pitch trim controls.
b Make sure that these circuit breakers are closed:
PANEL DESIGNATION FIN LOCATION SEE NOTES
FCPC3 STBY COM 7CE6 (1) (2)
FCPC3 STBY MON 7CE5 (1) (2)
FCDC 2 6CE2 (1) (2)
FCSC 2 10CE2 (1) (2)
THS ACTR MOT 3 5CS3 (1) (2)
THS ACTR MOT2 NORM 5CS2 (1) (2)
FCPC 3 7CE3 (1) (2)
FCPC 2 NORM 7CE2 (1) (2)
FCPC 3 7CE4 (1) (2)
FCSC 1 NORM 10CE1 (1) (2)
FCPC 1 NORM 7CE1 (1) (2)
FCDC 1 6CE1 (1) (2)
FCSC 1 STBY 9CE (1) (2)
FCPC 1 STBY 11CE (1) (2)
THS ACTR MOT 1 5CS1 (1) (2)
NOTE(S)
(1): For circuit breaker safety practices, refer to Ref. AMM T ask 20-16-00-912-801.
(2): For the circuit breaker location, refer to Ref. AMM 24-00-00, Page Block 001.
c Get Access.
<1> Get access to the applicable FIN 5000VE series panel(s), refer to
Ref. AMM T ask 31-18-00-010-801.
d Make sure that circuit breaker ELSD
FIN 59CS located in Panel 5000VE is closed.
2 Procedure:
a Operational Check of the THSA Load Sensing Device, refer to Ref. Fig.
Location of test connector.

### Page 49

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 49
<1> T wo persons are necessary: One person in the cockpit and one
person at the THSA and Bulk cargo area.
ACTION RESULT
1.On the left side of the upper Electronic
Centralized Aircraft Monitoring (ECAM)
Display Unit (DU):
- Make sure that there is no "PRIM 2
PITCH FAULT" warning.
2.On the ELSD at the THSA:
- Disconnect the test connector.
On the left side of the upper ECAM DU:
- The "PRIM 2 PITCH FAULT" warning
comes into view.
3.On APU Panel 5000VE:
- Open C/B FIN 59CS
4.On overhead Panel 212VU: On overhead Panel 212VU:
- Release, then push the FLT CTL/PRIM 2
pushbutton switch.
- The OFF legend of PRIM 2 pushbutton
switch comes on, then goes off.
On the left side of the upper ECAM DU:
- The "PRIM 2 PITCH FAULT" warning
goes out of view.
5.On APU Panel 5000VE:
- Close C/B FIN 59CS.
On the left side of the upper ECAM DU:
- The "PRIM 2 PITCH FAULT" warning
comes into view.
6.On the ELSD at the THSA:
- Connect the test connector.
7.On overhead Panel 212VU:
- Release, then push the FLT CTL/PRIM 2
pushbutton switch.
On overhead Panel 212VU:
- The OFF legend of PRIM 2 pushbutton
switch comes on, then goes off.
On the left side of the upper ECAM DU:
- The "PRIM 2 PITCH FAULT" warning
goes out of view.
3 Close-up:
a Set tumbler switch FIN 4LJ to the "OFF" position.
b Depressurize the Blue and Yellow hydraulic systems, refer to Ref.
AMM T ask 29-00-00-864-802 and Ref. AMM T ask 29-00-00-864-803.
c Do the EIS stop procedure, refer to Ref. AMM T ask 31-60-00-860-802.
d Remove the warning notice(s).
(b) Do the Operational T est of the THS Actuator, refer to Ref. AMM T ask 27-44-00-
710-805.

### Page 50

A340
SERVICE BULLETIN
Figure ICN-A340-A-27XX4214-A-FAPE3-01ACP-A-001-01 SHEET 1/1
REV 00 Oct 12/20 A340-27-4214Location of test connector
Page 50
CONF ALL
B
A
FR87
FR86
FR87
FR80
FR86
Z310
A
312AR
LSD
TEST
CONNECTOR
B
ICN-A340-A-27XX4214-A-FAPE3-01ACP-A-001-01

### Page 51

A340
SERVICE BULLETIN
REV 00 Oct 12/20 A340-27-4214
Page 51
F. CLOSE-UP
(1) Task A340-A-27-XX-4214-01001-740A-A (A340-A-27-XX-4214-01ZZZ-740Z-A)
Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Referenced Information
Manuals/Drawings References/Sheets
AMM
T ask 24-41-00-862-801
T ask 25-54-00-400-801
T ask 52-30-00-410-803
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Remove the warning notices.
(c) Install the sidewall Panel 162RW and Panel 162KW, refer to Ref. AMM T ask 25-54-
00-400-801.
(d) Close the access Door 312AR.
(e) On the Panel 5026VE, set the cargo compartment light switch to the "OFF"
position.
(f) Close the bulk cargo-compartment Door 823, refer to Ref. AMM T ask 52-30-00-
410-803.
(g) Remove the access platform(s).
(h) De-energize the aircraft electrical circuits, refer to Ref. AMM T ask 24-41-00-862-
801.
(i) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A340-A-27-XX-4214-01001-90AA-A (A340-A-27-XX-4214-01ZZZ-90AZ-A)
Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 52

A340
SERVICE BULLETIN
APPENDIX
REV 00 Oct 12/20 A340-27-4214
Page 52
APPENDIX
A. REPORTING SHEET
TITLE: FLIGHT CONTROLS - TRIMMABLE HORIZONTAL STABILIZER (THS)
HYDRAULIC ACTUATION - INSTALL ELSD ON THSA
MODIFICATION No.: 205979S33745 206264S33801
(1) SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance
and Flight Operations Products if it is duly reported to Airbus.
(2) GENERAL information
The SB Reporting policy is published in ISI 00.00.00135. This document provides
information regarding: the SB Reporting means and benefits, the update of
customized Maintenance Products and customized Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations
Products" for further information on the update of affected Flight Operations Products.
(3) SB Reporting procedure
Standard practice to report SB is to use the online reporting application on
AirbusWorld.
Refer to ISI 00.00.00179:
- For complete information on reporting means to Airbus, Question 2 "What are
the standard practices for SB Reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs,
Question 3 "What about the reporting of prerequisite Service Bulletins?"
NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.

### Page 53

A340
SERVICE BULLETIN
APPENDIX
REV 00 Oct 12/20 A340-27-4214
Page 53
B. QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin.
The reported data that you provide us will be used to analyse areas of difficulties and to
take corrective action to further improve the quality of our Service Bulletin.
We thank you for the time you have taken in completing this form.
Quality rating of this SB 4 3 2 1
Quality rating of the Accomplishment Instructions 4 3 2 1
Quality rating of the Illustrations 4 3 2 1
Is this SB easy to understand ? Y / N
NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score
If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.
Planning Material Instructions
X Applicability X T ooling X Preparation
X Reason X List of Materials
Operator Supplied
X Mod/Inspection
X Manpower X Kit content X T est
X References X Re-identification X Close-up
X Publication X Illustrations
X Industry Support
Comments :
Operator : Date :
Name/Title
Please return this form to :
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
Or via your Resident Customer Support Office.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
