# Airbus Service Bulletin A340-32-4315

Copy: No revision named ("A340-32-4315 R00"), 41 pages: PDF https://openairdocs.org/files/sha256/34/cd/34cdcb8bc12df658afe0e4fc5a256064f82a5a2c157214c612e6c6f641c04586; text https://openairdocs.org/service-documents/airbus/a340-32-4315/file/34cdcb8bc12d.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2023-0011, the docket of AD 2023-12-19. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A340-32-4315
- Page: https://openairdocs.org/service-documents/airbus/a340-32-4315

## Text (41 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2023-0011, the docket of AD 2023-12-19. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

@A340
SERVICE BULLETIN
SUMMARY
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
This summary is for information only and is not approved for modification of the aircraft.
ATA SYSTEM: 32
TITLE: LANDING GEAR - MAIN GEAR - INTRODUCE A NEW STD OF
ENHANCED MLG BOGIE PIVOT PIN
**CONF ALL
MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR
 207165H16972
MINOR
 None
NOTE
: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting the
airworthiness of the product. All other changes are major changes.
REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
There has been an in service occurrences of damage being found on the bogie pivot pin. The probable
root cause of this damage is due to operation on runways that increase the pressure-velocity in the joint
leading to the production of a higher than acceptable energy input into the bogie pivot joint which
results in heat damage to the bogie pivot pin.
The aim of this Service Bulletin is to improve the robustness of the bogie pivot pin in high pressure-
velocity environments. Specifically when oscillations close to the natural frequency of the bogie beam
assembly are encountered.
This Service Bulletin introduces:
- A bogie pivot pin fabricated from CRES custom 465 H950 with chrome plating
- Sliding tube and bogie beam bushes fabricated from copper alloy (ToughMet 3) material with
ladder-grooves
- Bogie pivot pin nut and locking ring fabricated from CRES 13-8 Mo H1000 with chrome plating
- Bolts and washers fabricated from CRES A286
- MIL-PRF-23827 Type 1 grease.
This Service Bulletin is published to advise all operators of A340 aircraft of the issue of SAFRAN
LANDING SYSTEMS UK Ltd Service Bu lletin No. A33/34-32-315 which r eplaces the bogie pivot pin.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 2

@A340
SERVICE BULLETIN
SUMMARY
Accomplishment of this Service Bulletin will improve the robustness of the bogie pivot pin in high
pressure/velocity environments, therefore becoming more resistant to localized overheating.
Accomplishment of this Service Bulletin cancels the requirements of AD 2012-0053 and Service Bulletin
No. A340-32-4281.
This Modification Service Bulletin concerns the airworthiness limitations of Airworthiness Limitation
Section (ALS) Part 1 which is introduced within the A/C maintenance program under the operator
responsibility. Please download the relevant ALS Variation on AirbusWorld.
GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE
 RECOMMENDED (1)
 CANCELS INSPECTION SB
 YES
POTENTIAL AD
 NO
 A/C OPERATION AFFECTED
 NO
RELIABILITY AFFECTED
 NO
 PAX COMFORT AFFECTED
 NO
COST SAVING
 NO
 LROPS AFFECTED
 NO
STRUCTURAL LIFE EXTN
 NO
 VENDOR SB INVOLVED
 YES
A/C MAINTENANCE
JACKING
YES
NOTE
 (1)
: Service Bulletin recommended to be accomplished to prevent significant operational
disruptions.
MATERIAL PRICE INFORMATION
No Material
EFFECTIVITY
This Service Bulletin is applicable to this (these) operator(s) :
06Y 09M 17M 39N 78U 82M 83V ABB ABD AFR AIB ARG AXY
BOE CAL CPA DLH EDW F2I GAF HFM HFY IBE IRM KMF MAU
MDG MRJ PAL PUE QQE ROI SAA SAS SLM SWR SYR THT THY
U6A
CONCURRENT REQUIREMENTS
None
REFERENCES / REPERCUSSIONS
TFU
 None
OEB
 None
AOT
 None
SIL
 None
ISI
 None
LINE MAINTENANCE AFFECTED
 No
LIFE LIMIT
 None
OTHER
 None
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 2
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 3

@A340
SERVICE BULLETIN
SUMMARY
NATURE OF THE WORK
AIRCRAFT
 NO
EQUIPMENT
 YES
MANPOWER
Task 324315-831-897-001: Modification by Replacement of the Bogie Pivot Pin in accordance
with VSB
TOTAL MANHOURS
 24.00
ELAPSED TIME (HOURS)
 7.25
Additional manhours relat ed to Vendor SB; refer to:
Modify the MLG, LH side
 SAFRAN LANDING SYSTEMS UK
Ltd Service Bulletin No.
A33/34-32-315
Modify the MLG, RH side
 SAFRAN LANDING SYSTEMS UK
Ltd Service Bulletin No.
A33/34-32-315
Install the Bogie Pivot Pin, LH side
 SAFRAN LANDING SYSTEMS UK
Ltd Service Bulletin No.
A33/34-32-315
Install the Bogie Pivot Pin, RH side
 SAFRAN LANDING SYSTEMS UK
Ltd Service Bulletin No.
A33/34-32-315
Re-identify the MLG, LH side
 SAFRAN LANDING SYSTEMS UK
Ltd Service Bulletin No.
A33/34-32-315
Re-identify the MLG, RH side
 SAFRAN LANDING SYSTEMS UK
Ltd Service Bulletin No.
A33/34-32-315
APPENDICES
Appendix 01 - Manpower Gantt Chart
Appendix 02 - Glossary
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 3
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 4

@A340
SERVICE BULLETIN
SUMMARY
**CONF ALL
A
Z741
Z731
A
A
LH SHOWN
RH SYMMETRICAL
RE−IDENTIFICATION OF THE BOGIE AND
DRESSINGS                AND5010GM 5011GM
RE−IDENTIFICATION OF THE STRUT−MAIN AND
DRESSINGS                AND5018GM 5019GM
MODIFICATION OF THE BOGIE PIVOT PIN
F_SB_324315_7_SAAA_01_01
Figure A-USAAA - Sheet 01
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 4
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 5

@A340
SERVICE BULLETIN
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
ATA SYSTEM: 32
TITLE: LANDING GEAR - MAIN GEAR - INTRODUCE A NEW STD OF
ENHANCED MLG BOGIE PIVOT PIN
MODIFICATION No.: 207165H16972
This document contains AIRBUS PROPRIETARY INFORMATION and shall at all times remain the
property of AIRBUS; no intellectual property right or licence is granted by AIRBUS in connection with
any information contained in it. It is delivered on the express condition that said document and the
information contained in it shall be treated as confidential, shall not be used for any purpose other than
that for which it is hereby delivered. It shall not be disclosed in whole or in part to third parties and shall
not be duplicated in any manner (except for the purposes of performing the tasks described hereunder
and provided that any recipient of such document shall comply with the conditions herein), without
AIRBUS prior written consent.
1. PLANNING INFORMATION
**CONF ALL
A. EFFECTIVITY
NOTE
: This Service Bulletin is only applicable to aircraft on which MOD No.
54500H15561 or Service Bulletin No. A340-32-4256 is embodied.
(1) Models
340-312 340-313
(2) Effectivity by MSN
0117 0123 0126 0128 0135 0139 0149 0152 0158 0163-0164 0166-0168 0170
0174-0175 0179-0180 0185-0186 0190 0192-0194 0197 0199 0201-0202 0207-0208
0210 0212-0215 0217-0218 0221 0227 0233 0236-0237 0242-0243 0245-0246 0252
0257 0260 0264 0268 0270 0274 0278 0280 0282 0292 0297 0302 0304 0307 0310
0318-0319 0321 0325 0327 0329 0331-0332 0335 0347 0352 0354-0355 0367
0373-0374 0377-0379 0381 0385 0387 0390 0395 0399 0402 0406 0411 0413 0415
0424 0430 0433-0435 0438 0446-0447 0450 0459 0467 0470 0474 0483 0528 0538
0541 0544-0546 0554 0556 0559 0561-0562 0582 0585 0590 0598 0643 0646 0651
0668 0793 0800 0835 0844 0921 0938 0955
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 6

@A340
SERVICE BULLETIN
(3) Effectivity by Operator
The Operator/MSN relationship is provided for information only and is correct at the time
of issue in accordance with the information available to AIRBUS. Any future changes
resulting from transfer of an aircraft from one operator to another will not be reflected in
this list unless the Service Bulletin is revised for another reason.
OPERATOR
 MSN
06Y
 0139 0149
09M
 0483
17M
 0955
39N
 0168 0174
78U
 0175 0179
82M
 0208
83V
 0280
ABB
 0835 0844
ABD
 0210
AFR
 0186 0207 0237 0245 0246 0260 0307 0310 0377
AIB
 0192 0243 0264 0921 0938
ARG
 0123 0126 0128 0170 0193
AXY
 0374
BOE
 0554
CAL
 0402 0406 0411 0415 0433 0541
CPA
 0218 0227
DLH
 0135 0158 0213 0233 0252 0297 0304 0321 0325 0327 0335 0347
0352 0354 0379 0390 0434 0447
EDW
 0561 0562
F2I
 0214
GAF
 0274 0355
HFM
 0117 0163 0166 0185 0236 0367
HFY
 0190 0202
IBE
 0217 0221 0329
IRM
 0164 0282 0292
KMF
 0278
MAU
 0152 0194 0268 0793 0800
MDG
 0319
MRJ
 0257
PAL
 0302 0318 0332 0387 0459 0474
PUE
 0212 0215 0399
QQE
 0528
ROI
 0199 0201
SAA
 0197 0378 0544 0582 0590 0643 0646 0651
SAS
 0167 0413 0424 0430 0435 0450 0467 0470
SLM
 0242
SWR
 0538 0545 0546 0556 0559 0585 0598
SYR
 0381
THT
 0385 0395 0438 0446 0668
THY
 0180 0270 0331
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 2
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 7

@A340
SERVICE BULLETIN
OPERATOR
 MSN
U6A
 0373
(4) Configuration by MSN
MSN
 CONFIGURATION
0117 0123 0126 0128 0135 0139 0149 0152 0158 0163 0164
0166 0167 0168 0170 0174 0175 0179 0180 0185 0186 0190
0192 0193 0194 0197 0199 0201 0202 0207 0208 0210 0212
0213 0214 0215 0217 0218 0221 0227 0233 0236 0237 0242
0243 0245 0246 0252 0257 0260 0264 0268 0270 0274 0278
0280 0282 0292 0297 0302 0304 0307 0310 0318 0319 0321
0325 0327 0329 0331 0332 0335 0347 0352 0354 0355 0367
0373 0374 0377 0378 0379 0381 0385 0387 0390 0395 0399
0402 0406 0411 0413 0415 0424 0430 0433 0434 0435 0438
0446 0447 0450 0459 0467 0470 0474 0483 0528 0538 0541
0544 0545 0546 0554 0556 0559 0561 0562 0582 0585 0590
0598 0643 0646 0651 0668 0793 0800 0835 0844 0921 0938
0955
001
(5) Configuration definition
**CONF 001
Config. 001 is valid for all the aircraft given in the effectivity of this Service Bulletin as a
standard configuration.
(6) Material Effectivity
MATERIAL
 QTY PER A/C
 SEE NOTES
Reidentified part set REIDB01
 2
Consumable CMLB01
 2
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
There has been an in service occurrences of damage being found on the bogie pivot
pin. The probable root cause of this damage is due to operation on runways that
increase the pressure-velocity in the joint leading to the production of a higher than
acceptable energy input into the bogie pivot joint which results in heat damage to the
bogie pivot pin.
(2) Objective/Action
The aim of this Service Bulletin is to improve the robustness of the bogie pivot pin in
high pressure-velocity environments. Specifically when oscillations close to the natural
frequency of the bogie beam assembly are encountered.
This Service Bulletin introduces:
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 3
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 8

@A340
SERVICE BULLETIN
- A bogie pivot pin fabricated from CRES custom 465 H950 with chrome plating
- Sliding tube and bogie beam bushes fabricated from copper alloy (ToughMet 3)
material with ladder-grooves
- Bogie pivot pin nut and locking ring fabricated from CRES 13-8 Mo H1000 with
chrome plating
- Bolts and washers fabricated from CRES A286
- MIL-PRF-23827 Type 1 grease.
This Service Bulletin is published to advise all operators of A340 aircraft of the issue
of SAFRAN LANDING SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315 which
replaces the bogie pivot pin.
(3) Advantages
Accomplishment of this Service Bulletin will improve the robustness of the bogie
pivot pin in high pressure/velocity environments, therefore becoming more resistant to
localized overheating.
(4) Operational/Maintenance Consequences
Accomplishment of this Service Bulletin cancels the requirements of AD 2012-0053 and
Service Bulletin No. A340-32-4281.
This Modification Service Bulletin concerns the airworthiness limitations of Airworthiness
Limitation Section (ALS) Part 1 which is introduced within the A/C maintenance program
under the operator responsibility. Please download the relevant ALS Variation on
AirbusWorld.
D. DESCRIPTION
To accomplish this Service Bulletin it is necessary to :
Task 324315-831-897-001: Modification by Replacement of the Bogie Pivot Pin in accordance
with VSB
(1) Remove the Bogie Pivot Pin, LH side
(2) Remove the Bogie Pivot Pin, RH Side
(3) Modify the MLG, LH side
(4) Modify the MLG, RH side
(5) Preparation for Installation, LH side
(6) Preparation for Installation, RH side
(7) Install the Bogie Pivot Pin, LH side
(8) Install the Bogie Pivot Pin, RH side
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 4
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 9

@A340
SERVICE BULLETIN
(9) Re-identify the MLG, LH side
(10) Re-identify the MLG, RH side
E. COMPLIANCE
(1) Classification
RECOMMENDED: Service Bulletin recommended to be accomplished to prevent
significant operational disruptions.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin is recommended at the earliest opportunity
where manpower and facilities are available.
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the effectivity has a modification or repair embodied that is not of
AIRBUS origin, and which affects the content of this Service Bulletin, the operator is
responsible for obtaining approval by its airworthiness authority for any adaptation necessary
before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also not
included.
Task 324315-831-897-001: Modification by Replacement of the Bogie Pivot Pin in accordance
with VSB
Get Access
 7.50
On Aircraft
Remove the Bogie Pivot Pin, LH side
 2.00
Remove the Bogie Pivot Pin, RH Side
 2.00
Preparation for Installation, LH side
 1.00
Preparation for Installation, RH side
 1.00
Tests
 4.00
Close-Up
 6.50
TOTAL MANHOURS
 24.00
ELAPSED TIME (HOURS)
 7.25
Additional manhours relat ed to Vendor SB; refer to:
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 5
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 10

@A340
SERVICE BULLETIN
Task 324315-831-897-001: Modification by Replacement of the Bogie Pivot Pin in accordance
with VSB
Modify the MLG, LH side
 SAFRAN LANDING SYSTEMS UK
Ltd Service Bulletin No.
A33/34-32-315
Modify the MLG, RH side
 SAFRAN LANDING SYSTEMS UK
Ltd Service Bulletin No.
A33/34-32-315
Install the Bogie Pivot Pin, LH side
 SAFRAN LANDING SYSTEMS UK
Ltd Service Bulletin No.
A33/34-32-315
Install the Bogie Pivot Pin, RH side
 SAFRAN LANDING SYSTEMS UK
Ltd Service Bulletin No.
A33/34-32-315
Re-identify the MLG, LH side
 SAFRAN LANDING SYSTEMS UK
Ltd Service Bulletin No.
A33/34-32-315
Re-identify the MLG, RH side
 SAFRAN LANDING SYSTEMS UK
Ltd Service Bulletin No.
A33/34-32-315
NOTE
: For an explanation of the man-hours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA
 given in Appendix 01 - Manpower Gantt Chart .
H. WEIGHT AND BALANCE
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer’s Empty Weight (MEW) and do not include operator’s items. For the definition of
MEW and operator’s items, refer to the Weight and Balance Manual (WBM).
Manufacturers Empty Weight +8.6 KG (+19 LB)
Effect on Balance +330.2 KGM (+2388.3 LB.FT )
I. ELECTRICAL LOAD DATA
Not Changed
J. REFERENCES
Aircraft Maintenance Manual (AMM)
 06-20-00 07-11-00 12-34-24
20-21-11 32-00-00 32-11-14
Consumable Material List (CML)
Component Maintenance Manual Vendor (CMMv)
 32-12-62 32-12-64
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM)
 20-55-00
Service Bulletin (SB)
 A340-32-4256
A340-32-4281
Structural Repair Manual (SRM)
 51-24-00 51-42-00 51-43-00
Vendor Service Bulletin (VSB)
 SAFRAN LANDING SYSTEMS UK
Ltd Service Bulletin No.
A33/34-32-315
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 6
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 11

@A340
SERVICE BULLETIN
Weight and Balance Manual (WBM)
K. PUBLICATION AFFECTED
Airworthiness Limitation Section (ALS)
Aircraft Maintenance Manual (AMM)
 32-11-14
Illustrated Parts Catalog (IPC)
 32-11-11
L. INTERCHANGEABILITY/MIXABILITY
The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.
DESCRIPTION
 OLD PART N˚
 NEW PART N˚
 INT
 MIXABILITY
 SEE
NOTES
Strut-Main And
Dressings
10-210501-006
 10-210501-007
 01
 Not
Applicable
(1) (2)
Strut-Main And
Dressings
10-210601-006
 10-210601-007
 01
 Not
Applicable
(1) (2)
Bogie And Dressings
 10-211501-003
 10-211501-004
 01
 Not
Applicable
(1) (3)
Bogie And Dressings
 10-211501-XXX
 10-211501-XXX
 01
 Not
Applicable
(1) (4)
Strut-Main And
Dressings
10-210501-XXX
 10-210501-XXX
 01
 Not
Applicable
(1) (5)
Strut-Main And
Dressings
10-210601-XXX
 10-210601-XXX
 01
 Not
Applicable
(1) (6)
Strut-Main And
Dressings
10-210502-XXX
 10-210502-XXX
 01
 Not
Applicable
(1) (7)
Strut-Main And
Dressings
10-210602-XXX
 10-210602-XXX
 01
 Not
Applicable
(1) (8)
NOTE
: For definitions of interchangeability codes in column INT., refer to ATA
Common Support Data Dictionary (CSDD), Chapter 2.
NOTE
 (1)
: For the interchangeability of detail parts, refer to SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
NOTE
 (2)
: Old PN does not have Strike No. 14 cancelled. New PN has Strike No. 14
cancelled.
NOTE
 (3)
: Old PN does not have Strike No. 5 cancelled. New PN has Strike No. 5
cancelled.
NOTE
 (4)
: XXX shows the last three digits of any Bogie and Dressings part number
beginning with 10-211501. Old PN does not have Strike No. 5 cancelled. New
PN has Strike No. 5 cancelled.
NOTE
 (5)
: XXX shows the last three digits of any Main Strut and Dressing part number
beginning with 10-210501. Old PN does not have Strike No. 14 cancelled.
New PN has Strike No. 14 cancelled.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 7
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 12

@A340
SERVICE BULLETIN
NOTE
 (6)
: XXX shows the last three digits of any Main Strut and Dressing part number
beginning with 10-210601. Old PN does not have Strike No. 14 cancelled.
New PN has Strike No. 14 cancelled.
NOTE
 (7)
: XXX shows the last three digits of any Main Strut and Dressing part number
beginning with 10-210502. Old PN does not have Strike No. 14 cancelled.
New PN has Strike No. 14 cancelled.
NOTE
 (8)
: XXX shows the last three digits of any Main Strut and Dressing part number
beginning with 10-210602. Old PN does not have Strike No. 14 cancelled.
New PN has Strike No. 14 cancelled.
M. SPARES
Nut 201489622
Pin 55-2105029-00
Collar 55-2105101-00
The parts listed here must not be installed anymore on aircraft which have accomplished this
Service Bulletin or which have the equivalent production modification embodied.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 8
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 13

@A340
SERVICE BULLETIN
2. MATERIAL INFORMATION
**CONF ALL
A. MATERIAL - PRICE AND AVAILABILITY
No Material Set
B. INDUSTRY SUPPORT INFORMATION
AIRBUS will not provide industry support for accomplishment of this Service Bulletin.
This Service Bulletin is the subject of a SAFRAN LANDING SYSTEMS UK Ltd monitored
retrofit campaign.
Refer to SAFRAN LANDING SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315 for
industry support terms of the Vendor Service Bulletin parts and labor.
SAFRAN LANDING SYSTEMS UK Ltd
CHELTENHAM ROAD EAST
GLOUCESTER
GL2.90H
GLOUCESTERSHIRE
UNITED KINGDOM
as per SAFRAN LANDING SYSTEMS UK Ltd V endor Service Bu lletin (VSB) No.
A33/34-32-315.
C. LIST OF COMPONENTS
No Kit
D. LIST OF MATERIALS - OPERATOR SUPPLIED
(1) Consumable Materials
Consumable CMLB01
ITEM
 DESCRIPTION
 REFERENCE TO CML
MAT. No.
QTY PER A/C
 SEE
NOTES
Mineral Oil Base Grease-Anti-Seize
Lithium Thicke
03FCC2
 As required
Synthetic Oil Base Grease-General
Purpose Lithium
03GBC1
 As required
 (1)
Non Aqueous Cleaner-General
 08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
NOTE
 (1)
: Use MIL-PRF-23827 Type 1 grease.
(2) Components
NOTE
: To accomplish this Service Bulletin it is necessary to use the expendable
parts listed in the subs equent referenced tasks:
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 9
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 14

@A340
SERVICE BULLETIN
- AMM Task 32-11-14-410-801.
(3) Equipment
None
E. PARTS TO BE RE-IDENTIFIED BY OPERATOR
Reidentified part set REIDB01
ITEM
 NEW PART N˚
 KEYWORD
 ITEM
 OLD PART N˚
 SEE
NOTES
9
 10-211501-004
 BOGIE
 (9)
 10-211501-003
 (1) (2)
10-210501-007
 STRUT
 10-210501-006
 (2) (3)
10-210501-XXX
 STRUT
 10-210501-XXX
 (2) (4) (2)
(4)
10-210502-XXX
 STRUT
 10-210502-XXX
 (2) (5) (2)
(5)
10-210601-007
 STRUT
 10-210601-006
 (2) (3)
10-210601-XXX
 STRUT
 10-210601-XXX
 (2) (6) (2)
(6)
10-210602-XXX
 STRUT
 10-210602-XXX
 (2) (7) (2)
(7)
10-211501-XXX
 BOGIE
 10-211501-XXX
 (2) (8) (2)
(8)
NOTE
 (1)
: Old PN does not have Strike No. 5 cancelled. New PN has Strike No. 5
cancelled.
NOTE
 (2)
: For the re-identification of detai l parts, refer to SAFRAN LANDING SYSTEMS
UK Ltd Service Bulletin No. A33/34-32-315.
NOTE
 (3)
: Old PN does not have Strike No. 14 cancelled. New PN has Strike No. 14
cancelled.
NOTE
 (4)
: XXX shows the last three digits of any Main Strut and Dressings part number
beginning with 10-210501. Old PN does not have Strike No. 14 cancelled.
New PN has Strike No. 14 cancelled.
NOTE
 (5)
: XXX shows the last three digits of any Main Strut and Dressings part number
beginning with 10-210502. Old PN does not have Strike No. 14 cancelled.
New PN has Strike No. 14 cancelled.
NOTE
 (6)
: XXX shows the last three digits of any Main Strut and Dressings part number
beginning with 10-210601. Old PN does not have Strike No. 14 cancelled.
New PN has Strike No. 14 cancelled.
NOTE
 (7)
: XXX shows the last three digits of any Main Strut and Dressing part number
beginning with 10-210602. Old PN does not have Strike No. 14 cancelled.
New PN has Strike No. 14 cancelled.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 10
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 15

@A340
SERVICE BULLETIN
NOTE
 (8)
: XXX shows the last three digits of any Bogie and Dressings part number
beginning with 10-211501. Old PN does not have Strike No. 5 cancelled. New
PN has Strike No. 5 cancelled.
F. TOOLING
(1) Tooling - Price and Availability
None
(2) Tools
NOTE
: To accomplish this Service Bulletin it is necessary to use the tools listed
in the subsequent re ferenced tasks:
- AMM Task 32-11-14-010-801
- AMM Task 32-11-14-410-801
- CMMv 32-12-62
- CMMv 32-12-64.
(3) Special Tools
None
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 11
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 16

@A340
SERVICE BULLETIN
This Page Intentionally Left Blank
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 12
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 17

@A340
SERVICE BULLETIN
3. ACCOMPLISHMENT INSTRUCTIONS
Task 324315-831-897-001 - Modification by Replacement of the Bogie Pivot Pin in
accordance with VSB
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
WARNING
: MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING NOTICES ARE
IN POSITION BEFORE YOU START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR INJURE PERSONS.
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 13
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 18

@A340
SERVICE BULLETIN
NOTE
: This Service Bulletin contains the instructions for the on-aircraft maintenance
necessary to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions contained herein, contact AIRBUS for further
instructions and approval.
NOTE
: Discarded parts must be managed at the operator’s discretion.
Task Associated Data
Zone
731 741
Modified FIN
5010GM 5011GM 5018GM 5019GM
Manpower
TOTAL MANHOURS
 24.00
ELAPSED TIME (HOURS)
 7.25
Additional manhours related to Vendor SB; refer to:
SAFRAN LANDING SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315
A. GENERAL
(1) Subtask 324315-910-403-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-20-00, Page Block 001
Task 20-21-11-911-801
Consumable Material List (CML)
Structural Repair Manual (SRM)
 51-24-00
51-42-00
51-43-00
(a) For the specification of Material Numbers (Mat. No.) given in this Service Bulletin,
refer to the Consumable Materials List (CML).
(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.
(c) Remove and install fasteners in accordance with SRM 51-42-00.
(d) Get alternative and substitute fastener data in accordance with SRM 51-43-00.
(e) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-801.
(f) Apply sealant in accordance with SRM 51-24-00.
(g) Tag all the parts you must remove and retain to make the subsequent installation
easier.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 14
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 19

@A340
SERVICE BULLETIN
(h) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.
(2) Subtask 324315-839-403-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
B. PREPARATION
(1) Subtask 324315-941-403-001 - Job Set-up
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 Task 12-34-24-860-802
Task 32-00-00-481-802
Task 32-11-14-010-801
Component Maintenance Manual Vendor
(CMMv)
32-12-62
32-12-64
NOTE
: For the basic Aircraft configuration, refer to AMM Chapter ’Introduction -
Aircraft status for maintenance’ in Manual Front Matter section.
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-860-802.
(b) Install the safety devices on the MLG, refer to AMM Task 32-00-00-481-802.
(c) Do the job set-up procedure as specified in the removal of the MLG bogie beam
assembly for access, complete with wheels and breaks, refer to AMM Task
32-11-14-010-801.
(d) Do the preparation before the replacement of the sliding piston pivot bushes, Item
(7), in accordance with CMMv 32-12-62.
(e) Do the preparation before the replacement of the bogie beam pivot bushes, Item
(6), in accordance with CMMv 32-12-64.
C. PROCEDURE
(1) Subtask 324315-020-401-001 - Remove the Bogie Pivot Pin, LH side
Work Zones and Access Panels
Zone
 Access/Work location
731
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 15
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 20

@A340
SERVICE BULLETIN
Manpower Resources
Manhours
 2.00
Minimum number of person
 2
Subtask elapsed time
 1.00
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 Task 32-11-14-010-801
Component Maintenance Manual Vendor
(CMMv)
32-12-62
32-12-64
Structural Repair Manual (SRM)
 51-42-00
Vendor Service Bulletin (VSB)
 SAFRAN LANDING SYSTEMS UK Ltd
A33/34-32-315
Fig. A-UBAAA
Removal of Bogie Pivot Pin
Sheet 01
Sheet 02
WARNING
: USE GOGGLES WHEN YOU REMOVE OR INSTALL LOCKWIRE.
EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT
IMMEDIATELY. LOOSE LOCKWIRE CAN CAUSE INJURY AND/OR
DAMAGE.
NOTE
: For this procedure you will lift the aircraft on jacks until the aircraft weight
is off the bogie beam, so that the pivot pin can be turned.
(a) Remove the bogie pivot pin from the MLG, LH side
Refer to Fig. A-UBAAA Sheet 02
 , view B and AMM Task 32-11-14-010-801.
Refer to SAFRAN LANDING SYSTEMS UK Ltd Service Bulletin No.
A33/34-32-315.
In accordance with CMMv 32-12-62 and CMMv 32-12-64.
In accordance with SRM 51-42-00.
1
 Cut and discard the lockwire from the bolts, Item (1).
2
 Remove:
FIN 5010GM
1 Bogie And Dressings 10-211501-003 Item (9) Retain
attached with
3 Bolt Item (1) Discard
3 Washer-Flat Item (2) Discard
1 Collar 55-2105101-00 Item (3) Discard
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 16
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 21

@A340
SERVICE BULLETIN
1 Nut 201489622 Item (4) Discard
1 Pin 55-2105029-00 Item (5) Discard
4 Sliding Pivot-Bush Item (7) Discard
2 Bogie Pivot-Bush Item (6) Discard
(2) Subtask 324315-020-402-001 - Remove the Bogie Pivot Pin, RH Side
Work Zones and Access Panels
Zone
 Access/Work location
741
Manpower Resources
Manhours
 2.00
Minimum number of person
 2
Subtask elapsed time
 1.00
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 Task 32-11-14-010-801
Component Maintenance Manual Vendor
(CMMv)
32-12-62
32-12-64
Structural Repair Manual (SRM)
 51-42-00
Vendor Service Bulletin (VSB)
 SAFRAN LANDING SYSTEMS UK Ltd
A33/34-32-315
Fig. A-UBAAA
Removal of Bogie Pivot Pin
Sheet 01
Sheet 02
WARNING
: USE GOGGLES WHEN YOU REMOVE OR INSTALL LOCKWIRE.
EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT
IMMEDIATELY. LOOSE LOCKWIRE CAN CAUSE INJURY AND/OR
DAMAGE.
NOTE
: For this procedure you will lift the aircraft on jacks until the aircraft weight
is off the bogie beam, so that the pivot pin can be turned.
(a) Remove the bogie pivot pin, on RH side.
Refer to Fig. A-UBAAA Sheet 02
 , view B and AMM Task 32-11-14-010-801.
Refer to SAFRAN LANDING SYSTEMS UK Ltd Service Bulletin No.
A33/34-32-315.
In accordance with CMMv 32-12-62 and CMMv 32-12-64.
In accordance with SRM 51-42-00.
1
 Cut and discard the lockwire from the bolts, Item (1).
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 17
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 22

@A340
SERVICE BULLETIN
2
 Remove:
FIN 5010GM
1 Bogie And Dressings 10-211501-003 Item (9) Retain
attached with
3 Bolt Item (1) Discard
3 Washer-Flat Item (2) Discard
1 Collar 55-2105101-00 Item (3) Discard
1 Nut 201489622 Item (4) Discard
1 Pin 55-2105029-00 Item (5) Discard
4 Sliding Pivot-Bush Item (7) Discard
2 Bogie Pivot-Bush Item (6) Discard
(3) Subtask 324315-831-405-001 - Modify the MLG, LH side
Work Zones and Access Panels
Zone
 Access/Work location
731
References
Vendor Service Bulletin (VSB)
 SAFRAN LANDING SYSTEMS UK Ltd
A33/34-32-315
CAUTION
: COMPLETE REMOVAL OF THE OLD GREASE FROM THE BOGIE
PIVOT PINS, INTERFACING BU SHES AND GR EASE SUPPLY
DRILLINGS MUST BE DONE TO PREVENT CONTAMINATION OF
THE NEW GREASE. CONTAMINATION OF GREASE CAN CAUSE
DAMAGE TO THE COMPONENTS IN THIS ASSEMBLY. IT IS
NORMAL FOR GREASE TO ACCUMULATE IN THE BOGIE BEAM
BORE AROUND THE BOGIE PIVOT PIN. IT IS IMPORTANT
THAT THE ENVIRONMENTAL PROTECTION IN THIS AREA IS
NOT DAMAGED. IT IS NOT REQUIRED TO REMOVE ANY
GREASE DEPOSITED IN THE BOGIE BEAM BORE. INCORRECT
REMOVAL OF GREASE IN THIS AREA COULD DAMAGE THE
ENVIRONMENTAL PROTECTION OF THE BOGIE BEAM.
(a) Modify the MLG in accordance w ith the SAFRAN LANDING SYSTEMS UK Ltd
Service Bulletin No. A33/34-32-315.
NOTE
: Make sure the new grease comes through the lubrication fittings so
that all old grease is removed.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 18
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 23

@A340
SERVICE BULLETIN
(4) Subtask 324315-831-406-001 - Modify the MLG, RH side
Work Zones and Access Panels
Zone
 Access/Work location
741
References
Vendor Service Bulletin (VSB)
 SAFRAN LANDING SYSTEMS UK Ltd
A33/34-32-315
CAUTION
: COMPLETE REMOVAL OF THE OLD GREASE FROM THE BOGIE
PIVOT PINS, INTERFACING BU SHES AND GR EASE SUPPLY
DRILLINGS MUST BE DONE TO PREVENT CONTAMINATION OF
THE NEW GREASE. CONTAMINATION OF GREASE CAN CAUSE
DAMAGE TO THE COMPONENTS IN THIS ASSEMBLY. IT IS
NORMAL FOR GREASE TO ACCUMULATE IN THE BOGIE BEAM
BORE AROUND THE BOGIE PIVOT PIN. IT IS IMPORTANT
THAT THE ENVIRONMENTAL PROTECTION IN THIS AREA IS
NOT DAMAGED. IT IS NOT REQUIRED TO REMOVE ANY
GREASE DEPOSITED IN THE BOGIE BEAM BORE. INCORRECT
REMOVAL OF GREASE IN THIS AREA COULD DAMAGE THE
ENVIRONMENTAL PROTECTION OF THE BOGIE BEAM.
(a) Modify the MLG in accordance w ith the SAFRAN LANDING SYSTEMS UK Ltd
Service Bulletin No. A33/34-32-315.
NOTE
: Make sure the new grease comes through the lubrication fittings so
that all old grease is removed.
(5) Subtask 324315-640-401-001 - Preparation for Installation, LH side
Work Zones and Access Panels
Zone
 Access/Work location
731
Manpower Resources
Manhours
 1.00
Minimum number of person
 1
Subtask elapsed time
 1.00
Skills
 AIRFRAME
Material necessary to do the job
Consumable CMLB01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Mineral Oil Base Grease-
Anti-Seize Lithium Thicke
03FCC2
 As required
Synthetic Oil Base Grease-
General Purpose Lithium
03GBC1
 As required
 (1)
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 19
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 24

@A340
SERVICE BULLETIN
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Non Aqueous Cleaner-
General
08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
NOTE
 (1)
: Use MIL-PRF-23827 Type 1 grease.
References
Structural Repair Manual (SRM)
 51-24-00
Fig. A-UBAAA
Removal of Bogie Pivot Pin
Sheet 01
Sheet 02
WARNING
: IF YOU USE AN ABRASIVE MATERIAL ON THE MAIN BEARINGS OF
THE SHOCK ABSORBER AND THE BOGIE BEAM, YOU MUST NOT
GET THE METAL DUST:
- O NY O U RS K I N
- IN YOUR EYES
- IN YOUR RESPIRATORY SYSTEM.
THE BEARINGS ARE MADE OF BERYLLIUM COPPER AND THE
DUST CAN CAUSE YOU CANCER.
(a) Clean the following parts, refer to Fig. A-UBAAA Sheet 02
 ,v i e wB :
- Threaded parts of the bogie beam pivot pin, Item (5)
- Threaded parts of the nut, Item (4)
- Bogie pivot pin bush internal diameter and grease grooves.
with:
Textile-Lint Free
Cotton
14SBA1 As required
and
Non Aqueous
Cleaner-General
08BAA9 As required
NOTE
: The solvent must not be poured directly onto any part of the bogie
beam bore.
(b) Apply to the following parts:
Refer to Fig. A-UBAAA Sheet 02
 ,v i e wB :
In accordance with SRM 51-24-00.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 20
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 25

@A340
SERVICE BULLETIN
- Threads and splines of the bogie pivot pin, Item (5)
- Threads of the nut, Item (4).
Mineral Oil Base
Grease-Anti-Seize
Lithium Thicke
03FCC2 As required
NOTE
: This consumable must be applied only after the installation of the
bogie pivot pin, Item (5), and before the installation of the nut, Item
(4).
(c) Do a visual inspection of the component interface and/or the adjacent area.
(d) Make sure that the parts retained from the removed component are clean and in
the correct condition.
(e) Lubricate the following parts:
- Parts of the pivot pin that are not threaded
- Attachment bores of the shock absorber
- Attachment bores of the bogie beam.
with:
Synthetic Oil Base
Grease-General
Purpose Lithium
03GBC1 As required
(6) Subtask 324315-640-402-001 - Preparation for Installation, RH side
Work Zones and Access Panels
Zone
 Access/Work location
741
Manpower Resources
Manhours
 1.00
Minimum number of person
 1
Subtask elapsed time
 1.00
Skills
 AIRFRAME
Material necessary to do the job
Consumable CMLB01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Mineral Oil Base Grease-
Anti-Seize Lithium Thicke
03FCC2
 As required
Synthetic Oil Base Grease-
General Purpose Lithium
03GBC1
 As required
 (1)
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 21
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 26

@A340
SERVICE BULLETIN
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Non Aqueous Cleaner-
General
08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
NOTE
 (1)
: Use MIL-PRF-23827 Type 1 grease.
References
Structural Repair Manual (SRM)
 51-24-00
Fig. A-UBAAA
Removal of Bogie Pivot Pin
Sheet 01
Sheet 02
WARNING
: IF YOU USE AN ABRASIVE MATERIAL ON THE MAIN BEARINGS OF
THE SHOCK ABSORBER AND THE BOGIE BEAM, YOU MUST NOT
GET THE METAL DUST:
- O NY O U RS K I N
- IN YOUR EYES
- IN YOUR RESPIRATORY SYSTEM.
THE BEARINGS ARE MADE OF BERYLLIUM COPPER AND THE
DUST CAN CAUSE YOU CANCER.
(a) Clean the following parts, refer to Fig. A-UBAAA Sheet 02
 ,v i e wB :
- Threaded parts of the bogie beam pivot pin, Item (5)
- Threaded parts of the nut, Item (4)
- Bogie pivot pin bush internal diameter and grease grooves.
with:
Textile-Lint Free
Cotton
14SBA1 As required
and
Non Aqueous
Cleaner-General
08BAA9 As required
NOTE
: The solvent must not be poured directly onto any part of the bogie
beam bore.
(b) Apply to the following parts:
Refer to Fig. A-UBAAA Sheet 02
 ,v i e wB :
In accordance with SRM 51-24-00.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 22
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 27

@A340
SERVICE BULLETIN
- Threads and splines of the bogie pivot pin, Item (5)
- Threads of the nut, Item (4).
Mineral Oil Base
Grease-Anti-Seize
Lithium Thicke
03FCC2 As required
NOTE
: This consumable must be applied only after the installation of the
bogie pivot pin, Item (5), and before the installation of the nut, Item
(4).
(c) Do a visual inspection of the component interface and/or the adjacent area.
(d) Make sure that the parts retained from the removed component are clean and in
the correct condition.
(e) Lubricate the following parts:
- Parts of the pivot pin that are not threaded
- Attachment bores of the shock absorber
- Attachment bores of the bogie beam.
with:
Synthetic Oil Base
Grease-General
Purpose Lithium
03GBC1 As required
(7) Subtask 324315-410-401-001 - Install the Bogie Pivot Pin, LH side
Work Zones and Access Panels
Zone
 Access/Work location
731
Material necessary to do the job
Reidentified part set REIDB01
ITEM
 NEW PART N˚
 KEYWORD
 ITEM
 OLD PART N˚
 SEE
NOTES
9
 10-211501-004
 BOGIE
 (9)
 10-211501-003
 (1) (2)
10-211501-XXX
 BOGIE
 10-211501-XXX
 (2) (3) (2)
(3)
NOTE
 (1)
: Old PN does not have Strike No. 5 cancelled. New PN has Strike No. 5
cancelled.
NOTE
 (2)
: For the re-identification of detail parts, refer to SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 23
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 28

@A340
SERVICE BULLETIN
NOTE
 (3)
: XXX shows the last three digits of any Bogie and Dressings part number
beginning with 10-211501. Old PN does not have Strike No. 5 cancelled.
New PN has Strike No. 5 cancelled.
Consumable CMLB01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Synthetic Oil Base Grease-
General Purpose Lithium
03GBC1
 As required
 (1)
NOTE
 (1)
: Use MIL-PRF-23827 Type 1 grease.
References
Aircraft Maintenance Manual (AMM)
 Task 32-11-14-400-801
Vendor Service Bulletin (VSB)
 SAFRAN LANDING SYSTEMS UK Ltd
A33/34-32-315
(a) Install the bogie pivot bush in acco rdance with the SAFRAN LANDING SYSTEMS
UK Ltd Service Bulletin No. A33/34-32-315.
(b) Install the sliding piston pivot bush in accordance with the SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
(c) Install the new instruction plates in accordance with the SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
(d) Install the bogie and dressings in accordance with the SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315 and AMM Task
32-11-14-400-801.
1
 After installation:
FIN 5010GM
1 Bogie And Dressings 10-211501-003 Item (9) Retained at
removal
becomes
FIN 5010GM
1 Bogie And Dressings 10-211501-004 Item 9
or
FIN 5010GM
1 Bogie And Dressings 10-211501-XXX
becomes
FIN 5010GM
1 Bogie And Dressings 10-211501-XXX
with strike number 5 cancelled.
NOTE
: Parts are re-identified in accordance with the SAFRAN
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 24
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 29

@A340
SERVICE BULLETIN
LANDING SYSTEMS UK Ltd Service Bulletin No.
A33/34-32-315.
(e) Apply grease to the bogie pivot pin in accordance with the SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
Synthetic Oil Base
Grease-General
Purpose Lithium
03GBC1 As required
(f)
CAUTION
: THE HEAD OF THE BOGIE PIVOT PIN MUST BE INBOARD ON
INSTALLATION.
Install the bogie pivot pin and its attaching parts in accordance with the SAFRAN
LANDING SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
(8) Subtask 324315-410-402-001 - Install the Bogie Pivot Pin, RH side
Work Zones and Access Panels
Zone
 Access/Work location
741
Material necessary to do the job
Reidentified part set REIDB01
ITEM
 NEW PART N˚
 KEYWORD
 ITEM
 OLD PART N˚
 SEE
NOTES
9
 10-211501-004
 BOGIE
 (9)
 10-211501-003
 (1) (2)
10-211501-XXX
 BOGIE
 10-211501-XXX
 (2) (3) (2)
(3)
NOTE
 (1)
: Old PN does not have Strike No. 5 cancelled. New PN has Strike No. 5
cancelled.
NOTE
 (2)
: For the re-identification of detail parts, refer to SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
NOTE
 (3)
: XXX shows the last three digits of any Bogie and Dressings part number
beginning with 10-211501. Old PN does not have Strike No. 5 cancelled.
New PN has Strike No. 5 cancelled.
Consumable CMLB01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Synthetic Oil Base Grease-
General Purpose Lithium
03GBC1
 As required
 (1)
NOTE
 (1)
: Use MIL-PRF-23827 Type 1 grease.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 25
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 30

@A340
SERVICE BULLETIN
References
Aircraft Maintenance Manual (AMM)
 Task 32-11-14-400-801
Vendor Service Bulletin (VSB)
 SAFRAN LANDING SYSTEMS UK Ltd
A33/34-32-315
(a) Install the bogie pivot bush in acco rdance with the SAFRAN LANDING SYSTEMS
UK Ltd Service Bulletin No. A33/34-32-315.
(b) Install the sliding piston pivot bush in accordance with the SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
(c) Install the new instruction plates in accordance with the SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
(d) Install the bogie and dressings in accordance with the SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315 and AMM Task
32-11-14-400-801.
1
 After installation:
FIN 5011GM
1 Bogie And Dressings 10-211501-003 Item (9) Retained at
removal
becomes
FIN 5011GM
1 Bogie And Dressings 10-211501-004 Item 9
or
FIN 5011GM
1 Bogie And Dressings 10-211501-XXX
becomes
FIN 5011GM
1 Bogie And Dressings 10-211501-XXX
with strike number 5 cancelled.
NOTE
: Parts are re-identified in accordance with the SAFRAN
LANDING SYSTEMS UK Ltd Service Bulletin No.
A33/34-32-315.
(e) Apply the grease to the bogie pivot pin in accordance with the SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
Synthetic Oil Base
Grease-General
Purpose Lithium
03GBC1 As required
(f)
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 26
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 31

@A340
SERVICE BULLETIN
CAUTION
: THE HEAD OF THE BOGIE PIVOT PIN MUST BE INBOARD ON
INSTALLATION.
Install the bogie pivot pin and its attaching parts in accordance with the SAFRAN
LANDING SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
(9) Subtask 324315-930-401-001 - Re-identify the MLG, LH side
Work Zones and Access Panels
Zone
 Access/Work location
731
Material necessary to do the job
Reidentified part set REIDB01
ITEM
 NEW PART N˚
 KEYWORD
 ITEM
 OLD PART N˚
 SEE
NOTES
10-210501-007
 STRUT
 10-210501-006
 (1) (2)
10-210501-XXX
 STRUT
 10-210501-XXX
 (2) (3) (2)
(3)
10-210601-XXX
 STRUT
 10-210601-XXX
 (2) (4) (2)
(4)
NOTE
 (1)
: Old PN does not have Strike No. 14 cancelled. New PN has Strike No.
14 cancelled.
NOTE
 (2)
: For the re-identification of detail parts, refer to SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
NOTE
 (3)
: XXX shows the last three digits of any Main Strut and Dressings part
number beginning with 10-210501. Old PN does not have Strike No. 14
cancelled. New PN has Strike No. 14 cancelled.
NOTE
 (4)
: XXX shows the last three digits of any Main Strut and Dressings part
number beginning with 10-210601. Old PN does not have Strike No. 14
cancelled. New PN has Strike No. 14 cancelled.
References
Vendor Service Bulletin (VSB)
 SAFRAN LANDING SYSTEMS UK Ltd
A33/34-32-315
(a) Re-identify the strut-main and dressings in accordance with the SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
FIN 5018GM
1 Strut-Main And
Dressings
10-210501-006
becomes
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 27
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 32

@A340
SERVICE BULLETIN
FIN 5018GM
1 Strut-Main And
Dressings
10-210501-007
or
FIN 5018GM
1 Strut-Main And
Dressings
10-210501-XXX
becomes
FIN 5018GM
1 Strut-Main And
Dressings
10-210501-XXX
with strike number 14 cancelled
or
FIN 5018GM
1 Strut-Main And
Dressings
10-210601-XXX
becomes
FIN 5018GM
1 Strut-Main And
Dressings
10-210601-XXX
with strike number 14 cancelled.
NOTE
: Parts must be re-identified in accordance with SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
(10) Subtask 324315-930-402-001 - Re-identify the MLG, RH side
Work Zones and Access Panels
Zone
 Access/Work location
741
Material necessary to do the job
Reidentified part set REIDB01
ITEM
 NEW PART N˚
 KEYWORD
 ITEM
 OLD PART N˚
 SEE
NOTES
10-210502-XXX
 STRUT
 10-210502-XXX
 (1) (2) (1)
(2)
10-210601-007
 STRUT
 10-210601-006
 (2) (3)
10-210602-XXX
 STRUT
 10-210602-XXX
 (2) (4) (2)
(4)
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 28
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 33

@A340
SERVICE BULLETIN
NOTE
 (1)
: XXX shows the last three digits of any Main Strut and Dressings part
number beginning with 10-210502. Old PN does not have Strike No. 14
cancelled. New PN has Strike No. 14 cancelled.
NOTE
 (2)
: For the re-identification of detail parts, refer to SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
NOTE
 (3)
: Old PN does not have Strike No. 14 cancelled. New PN has Strike No.
14 cancelled.
NOTE
 (4)
: XXX shows the last three digits of any Main Strut and Dressing part
number beginning with 10-210602. Old PN does not have Strike No. 14
cancelled. New PN has Strike No. 14 cancelled.
References
Vendor Service Bulletin (VSB)
 SAFRAN LANDING SYSTEMS UK Ltd
A33/34-32-315
(a) Re-identify the strut-main and dressings in accordance with the SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
FIN 5019GM
1 Strut-Main And
Dressings
10-210601-006
becomes
FIN 5019GM
1 Strut-Main And
Dressings
10-210601-007
or
FIN 5019GM
1 Strut-Main And
Dressings
10-210502-XXX
becomes
FIN 5019GM
1 Strut-Main And
Dressings
10-210502-XXX
with strike number 14 cancelled
or
FIN 5019GM
1 Strut-Main And
Dressings
10-210602-XXX
becomes
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 29
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 34

@A340
SERVICE BULLETIN
FIN 5019GM
1 Strut-Main And
Dressings
10-210602-XXX
with strike number 14 cancelled.
NOTE
: Parts must be re-identified in accordance with SAFRAN LANDING
SYSTEMS UK Ltd Service Bulletin No. A33/34-32-315.
D. TEST
(1) Subtask 324315-700-402-001 - Test
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 Task 32-11-14-400-801
(a) Do the test as specified after the installation of the MLG bogie beam assembly,
refer to AMM Task 32-11-14-400-801.
E. CLOSE-UP
(1) Subtask 324315-942-402-001 - Close-up
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 Task 07-11-00-586-801
Task 32-00-00-081-801
Task 32-00-00-081-802
(a) Remove the safety devices from the landing gear and landing gear doors, refer to
AMM Task 32-00-00-081-801 and AMM Task 32-00-00-081-802.
(b) Lower the aircraft off the ja cks, refer to AMM Task 07-11-00-586-801.
(c) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(d) Put the aircraft back to its initial configuration.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 30
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 35

@A340
SERVICE BULLETIN
**CONF ALL
A
Z741
Z731
A
A
LH SHOWN 
RH SYMMETRICAL
B
F_SB_324315_7_BAAA_01_01
Figure A-UBAAA - Sheet 01
Removal of Bogie Pivot Pin
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 31
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 36

@A340
SERVICE BULLETIN
**CONF ALL
(3)
(4)
(7)
(5)
(7)
(7)
(7)
(6)
(6)
(1)
(2)
x3
x3
B
(9)
9
F_SB_324315_7_BAAA_02_01
Figure A-UBAAA - Sheet 02
Removal of Bogie Pivot Pin
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 32
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 37

@A340
SERVICE BULLETIN
Appendix 01 - Manpower Gantt Chart
**CONF ALL
For an explanation of the man-hours and elapsed time, refer to the next page(s).
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 38

@A340
SERVICE BULLETIN
Appendix 01 - Manpower Gantt Chart
**CONF ALL
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A340−32−4315
GET ACCESS
MH ET/S
TOTAL MANHOURS
SB ELAPSED TIME
24.00
7.25
STEPS
7.50 2.25
50
TEST 4.00 1.00
CLOSE−UP 6.50 2.00
MH
ET/S:
PER
MANHOURS
ELAPSED TIME PER STEP
NUMBER OF PERSONS
01
02
THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
01
02
NOTE:
PER
4
4
4
:
:
SB ELAPSED TIME
(HOURS)
1234
IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
ARE NOT REFLECTED IN THIS GANTT CHART.
REMOVE THE BOGIE 2.00 1.002
PIVOT PIN, LH SIDE
REMOVE THE BOGIE 2.00 1.002
PIVOT PIN, RH SIDE
MODIFY THE MLG, LH REFER TO VSB
REFER TO VSB
REFER TO VSB
REFER TO VSB
REFER TO VSB
REFER TO VSB
MODIFY THE MLG, RH
PREPARATION FOR 1.00 1.00 1
INSTALLATION, LH SIDE
PREPARATION FOR 1.00 1.00 1
INSTALLATION, RH SIDE
INSTALL THE BOGIE
PIVOT PIN, LH SIDE
INSTALL THE BOGIE
PIVOT PIN, RH SIDE
RE−IDENTIFY THE MLG,
RE−IDENTIFY THE MLG,
LH SIDE
RH SIDE
SIDE
SIDE
67
F_SB_324315_7_AAAA_01_03
Figure A-UAAAA - Sheet 01
Manpower Gantt Chart
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 2
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 39

@A340
SERVICE BULLETIN
Appendix 02 - Glossary
**CONF ALL
ACRONYM
 FULL FORM
CRES
 Corrosion Resistant Steel
MLG
 Main Landing Gear
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 40

@A340
SERVICE BULLETIN
Service Bulletin REPORTING
TITLE: LANDING GEAR - MAIN GEAR - INTRODUCE A NEW STD OF
ENHANCED MLG BOGIE PIVOT PIN
MODIFICATION No.: 207165H16972
SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance and Flight
Operations Products if it is duly reported to Airbus.
General information
The SB Reporting policy is published in ISI 00.00.00135. This document provides information regarding:
the SB Reporting means and benefits, the update of customized Maintenance Products and customized
Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations Products" for
further information on the update of affected Flight Operations Products.
SB Reporting procedure
Standard practice to report SB is to use the online reporting application on AirbusWorld.
Refer to ISI 00.00.00179:
- For complete information on reporting means to Airbus. Question 2 "What are the standard
practices for SB reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs, Question 3 "What about
the reporting of prerequisite Service Bulletin?"
NOTE:
 ISI 00.00.00179 covers all the frequently asked questions about SB Reporting. It is revised on a
regular basis.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 41

@A340
SERVICE BULLETIN
QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin. The reported data
that you provide us will be used to analyse areas of difficulties and to take corrective action to further
improve the quality of our Service Bulletins.
We thank you for the time you have taken in completing this form.
(Please rate on a scale of 1 to 4, with 4 being the highest score)
- Quality rating of this SB 4321
- Quality rating of the Accomplishment Instructions 4321
- Quality rating of the Illustrations 4321
- Is this SB easy to understand ? Y/N
If you have had difficulties in the accomplishment of this SB please quote below the area(s) and give a
short description of the issue.
Planning Material Instructions
X Effectivity X Kit content X Preparation
X Reason X List of Materials Operator Supplied X Mod/Inspection
X Manpower X Industry support X Test
X References X Re-identification X Close-Up
X Publication X Tooling X Illustrations
Comments:
Operator: Date:
Name/Title:
Please return this form to:
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE
Attn : SEM4 Service Bulletins Management
F A X:( 3 3 )56 19 34 25 1
Or via your Resident Customer Support Office.
DATE: Dec 26/17 SERVICE BULLETIN No.: A340-32-4315
REVISION No.: 00 - Dec 26/17 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
