# Airbus Service Bulletin A340-35-5026

Copy: No revision named ("A340-35-5026 R00"), 48 pages: PDF https://openairdocs.org/files/sha256/38/e5/38e53a51f3a7ea0aa45791780948b8a820bfad522fff0dcde5c1b77a3c7a0fa1; text https://openairdocs.org/service-documents/airbus/a340-35-5026/file/38e53a51f3a7.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2021-0131, the docket of AD 2021-15-11. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A340-35-5026
- Page: https://openairdocs.org/service-documents/airbus/a340-35-5026

## Text (48 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2021-0131, the docket of AD 2021-15-11. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 1
CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
 
The content of this document is the property of Airbus.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.
MANDATORY MANDATORY MANDATORY
ATA SYSTEM: 35
TITLE: OXYGEN - CREW OXYGEN - INSPECTION OF THE OXYGEN SUPPLY
SOLENOID VALVE
MODIFICATION No.:
None

### Page 2

A340-500/600
SERVICE BULLETIN
SUMMARY
REV 00 Mar 29/19 A340-35-5026
Page 2
ATA SYSTEM: 35
TITLE: OXYGEN - CREW OXYGEN - INSPECTION OF THE OXYGEN SUPPLY
SOLENOID VALVE
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR None
MINOR None
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
B. REASON
(1) History
The Shut Off Valve (SOV) was identified as potential source for increased flow
resistance within the crew oxygen system.
(2) Objective/Action
The aim of this Inspection Service Bulletin is to ensure that the minimum mass flow of
supplemental oxygen required for each crew member is provided. This Service Bulletin
will also replace the solenoid valve in case of a test failure and collect the test results
afterwards.
(3) Advantages
Accomplishment of this Service Bulletin will contribute to ensure a sufficient flow of
oxygen supplied to the crew oxygen masks.
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE MANDATORY COST SAVING NO
A/C OPERATION
AFFECTED
NO VENDOR SB NO
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD YES
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO
NOTE: Service Bulletin must be accomplished.
D. MAINTENANCE CONFIGURATION
No specific aircraft maintenance configuration required.

### Page 3

A340-500/600
SERVICE BULLETIN
SUMMARY
REV 00 Mar 29/19 A340-35-5026
Page 3
E. MATERIAL PRICE INFORMATION
(1) Inspection
(a) T ask set A340-A-35-XX-5026-01000-93BA-A Inspection
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Equipment See SB See Note Valve
NOTE: Price information to be obtained from the given supplier.
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
06U 32P 41N 65W 72W 81Q 83V AHY AIB ARA DLH ETD F2I G4I GBB HFY I2L IBE IRM LHT
MLT QAF QTR R1T SAA SOU TAM THA THY VIR
G. CONCURRENT REQUIREMENTS
None
H. NATURE OF THE WORK
(1) Inspection
(a) T ask set A340-A-35-XX-5026-01000-93BA-A Inspection
AIRCRAFT YES
EQUIPMENT NO
I. MANPOWER
(1) Inspection
(a) T ask set A340-A-35-XX-5026-01000-93BA-A Inspection
MANPOWER
TOTAL MAN-HOURS 2.20 h
ELAPSED TIME (HOURS) 1.95 h

### Page 4

A340-500/600
SERVICE BULLETIN
SUMMARY
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR4-A-002-01 SHEET 1/1
REV 00 Mar 29/19 A340-35-5026General overview
Page 4
J. GENERAL OVERVIEW
CONF ALL
A
Z120
FR20
FR1
FR4
FR7
VIEW LOOKING FWD
 OCCUPANT
OXYGEN
THIRD
FIRST OFFICER
OXYGEN
CAPTAIN
OXYGEN
SHUT OFF
VALVE
A
Z210
B
B
C
NOTE:
INSPECTION AREA
ICN-A340-A-35XX5026-A-FAPE3-00NR4-A-002-01

### Page 5

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 5
ATA SYSTEM: 35
TITLE: OXYGEN - CREW OXYGEN - INSPECTION OF THE OXYGEN SUPPLY
SOLENOID VALVE
1. PLANNING INFORMATION
A. APPLICABILITY
(1) Models
ON A/C 0445, 0457, 0464, 0471, 0478, 0485, 0492, 0495, 0499, 0520, 0560, 0563, 0572,
0608, 0611, 0624, 0628, 0685, 0694, 0698, 0748, 0757, 0761, 0775, 0783, 0917, 1091, 1102
340-541
ON A/C 0886, 0894, 0902, 0910, 0912
340-542
ON A/C 0371, 0376, 0383, 0391, 0410, 0416, 0417, 0426, 0431, 0440, 0449, 0460, 0468,
0482, 0488, 0514, 0517, 0523, 0531, 0534, 0537, 0540, 0543, 0547, 0557, 0566, 0569,
0575, 0577, 0580, 0583, 0586, 0601, 0604, 0606, 0615, 0617, 0619, 0622, 0626, 0630,
0639, 0672, 0677, 0681, 0689, 0702, 0706, 0710, 0715, 0719, 0723, 0727, 0736, 0740,
0744, 0753, 0762-0768, 0771, 0779, 0787, 0790, 0794, 0798, 0804, 0812, 0829, 0837, 0846,
0848, 0870, 0897, 0924, 0929, 0933, 0953, 0960, 0972, 0981, 0987, 0993, 1005, 1017,
1030, 1040, 1079, 1122
340-642
CONF ALL
(2) Applicability by MSN
0371 0376 0383 0391 0410 0416 0417 0426 0431 0440 0445 0449 0457 0460 0464
0468 0471 0478 0482 0485 0488 0492 0495 0499 0514 0517 0520 0523 0531 0534
0537 0540 0543 0547 0557 0560 0563 0566 0569 0572 0575 0577 0580 0583 0586
0601 0604 0606 0608 0611 0615 0617 0619 0622 0624 0626 0628 0630 0639 0672
0677 0681 0685 0689 0694 0698 0702 0706 0710 0715 0719 0723 0727 0736 0740
0744 0748 0753 0757 0761-0768 0771 0775 0779 0783 0787 0790 0794 0798 0804
0812 0829 0837 0846 0848 0870 0886 0894 0897 0902 0910 0912 0917 0924 0929
0933 0953 0960 0972 0981 0987 0993 1005 1017 1030 1040 1079 1091 1102 1122
(3) MSN by configuration
MSN CONFIGURATION
0371 0376 0383 0391 0410 0416 0417 0426 0431 0440 0445
0449 0457 0460 0464 0468 0471 0478 0482 0485 0488 0492
0495 0499 0514 0517 0520 0523 0531 0534 0537 0540 0543
0547 0557 0560 0563 0566 0569 0572 0575 0577 0580 0583
0586 0601 0604 0606 0608 0611 0615 0617 0619 0622 0624
0626 0628 0630 0639 0672 0677 0681 0685 0689 0694 0698
0702 0706 0710 0715 0719 0723 0727 0736 0740 0744 0748
0753 0757 0761 0762 0763 0764 0765 0766 0767 0768 0771
0775 0779 0783 0787 0790 0794 0798 0804 0812 0829 0837
0846 0848 0870 0886 0894 0897 0902 0910 0912 0917 0924
0929 0933 0953 0960 0972 0981 0987 0993 1005 1017 1030
1040 1079 1091 1102 1122
001
(4) Configuration definition
Configuration 001
CONF 001 is applicable for all the aircraft affected by this Service Bulletin as a

### Page 6

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 6
standard configuration.
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
The Shut Off Valve (SOV) was identified as potential source for increased flow
resistance within the crew oxygen system.
(2) Objective/Action
The aim of this Inspection Service Bulletin is to ensure that the minimum mass flow of
supplemental oxygen required for each crew member is provided. This Service Bulletin
will also replace the solenoid valve in case of a test failure and collect the test results
afterwards.
(3) Advantages
Accomplishment of this Service Bulletin will contribute to ensure a sufficient flow of
oxygen supplied to the crew oxygen masks.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
T o accomplish this Service Bulletin it is necessary to:
(1) Inspection
(a) T ask set A340-A-35-XX-5026-01000-93BA-A Inspection
1 Determine the applicable Inspection Threshold
2 Do the Three Mask flow T est
3 Do the T wo Mask flow T est (Depending on the Inspection Result)
4 Do the One Mask flow T est (Depending on the Inspection Result)
5 Replace the Shut off Valve (Depending on the Inspection Result)
6 Do the Three Mask flow T est after replacement of the Shut off Valve
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
This Service Bulletin has been classified Mandatory. It is expected that an
Airworthiness Directive (AD) published by the European Aviation Safety Agency (EASA)
will be issued to confirm this classification. It is anticipated that the AD will confirm the
(thresholds and/or intervals and/or date) given but reference should be made to the
AD for confirmation of the mandated accomplishment timescale.
T able 1 — Compliance Time

### Page 7

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 7
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
Valve
manufacture
date or last
overhaul date/
component
maintenance
performed
before 2003.
Accomplishment
of this Service
Bulletin must
be done
Within 6
month(s) from
the first issue
of this SB
None None
Valve
manufacture
date or last
overhaul date/
component
maintenance
performed from
2003 until 2007
(included).
Accomplishment
of this Service
Bulletin must
be done
Within 9
month(s) from
the first issue
of this SB
None None
Valve
manufacture
date or last
overhaul date/
component
maintenance
performed from
2008 until 2011
(included).
Accomplishment
of this Service
Bulletin must
be done
Within 12
month(s) from
the first issue
of this SB
None None
Valve
manufacture
date or last
overhaul date/
component
maintenance
performed
since 2012.
Accomplishment
of this Service
Bulletin must
be done
Within 24
month(s) from
the first issue
of this SB
None None
NOTE: If an Overhaul/component maintenance is performed, the date this task is
accomplished is the date to be considered.
NOTE: The manufacturing date of the DVE90-0X solenoid valve is visible on its label.
If the placard is not readable, a review of the AIR / maintenance logs could
be an alternative to identify the P/N and S/N installed. If it is not possible
to obtain any data the unit should be handled as described for Units with
manufacture date before 2003.
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.

### Page 8

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 8
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Inspection
(a) T ask set A340-A-35-XX-5026-01000-93BA-A Inspection
PREPARATION
Job Set-up 0.50 h
PROCEDURE
Determine the applicable Inspection Threshold 0.25 h
Do the Three Mask flow T est 0.15 h
Do the T wo Mask flow T est (Depending on the Inspection
Result)
0.10 h
Do the One Mask flow T est (Depending on the Inspection
Result)
0.05 h
Replace the Shut off Valve (Depending on the Inspection
Result)
0.50 h
Do the Three Mask flow T est after replacement of the Shut
off Valve
0.15 h
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Close-up 0.50 h
TOTAL MAN-HOURS 2.20 h
ELAPSED TIME (HOURS) 1.95 h
NOTE: The minimum man-hours necessary to accomplish this Service Bulletin
are those for the Inspection. Depending on the inspection result,
additional man-hours can apply.
H. WEIGHT AND BALANCE
Not changed
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
(1) Inspection
(a) T ask set A340-A-35-XX-5026-01000-93BA-A Inspection
AIRCRAFT MAINTENANCE MANUAL (AMM)
06-20-00 06-31-53

### Page 9

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 9
AIRCRAFT MAINTENANCE MANUAL (AMM)
T ask 12-14-35-600-801 T ask 12-34-24-869-002
T ask 24-41-00-861-801 T ask 35-00-00-860-801
T ask 35-11-41-000-801
T ask 35-11-41-400-801
T ask 35-12-41-420-059
T ask 35-13-51-000-801
T ask 35-13-51-400-802
T ask 52-41-00-010-801
T ask 52-41-00-410-810
ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)
20-55-00
TROUBLE SHOOTING MANUAL (TSM)
T ask 35-10-00-810-807
K. PUBLICATION AFFECTED
None
L. INDUSTRY SUPPORT INFORMATION
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department: monitored.retrofit@airbus.com.
Industry support terms for the equipment must be negotiated with the equipment supplier.
Procurement terms for the equipment must be negotiated with the equipment supplier.

### Page 10

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 10
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
Material for task set A340-A-35-XX-5026-01000-93BA-A Inspection
MATERIAL QTY SEE NOTES
Equipment See SB
Referenced parts See SB
B. TOOLING
No tools
C. CONSUMABLES
No consumables
D. LIST OF NEW PARTS
Equipment for task set A340-A-35-XX-5026-01000-93BA-A Inspection
Procurement address F5341
ZODIAC
ZODIAC Aerospace Services Europa
61 Rue Pierre Curie
78373 Plaisir Cedex
France
Internet: www.zodiacaerospace.com
NOTE(S)
Vendor parts are to be procured from the address given above.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
DVE90-06 (F5341) 1 VALVE (1) (2)
DVE90-07 (F5341) 1 VALVE (1) (2)
NOTE(S)
(1): The components listed above are only necessary if the replacement is necessary. The
quantity of these items is to be ordered as required.
(2): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced parts for task set A340-A-35-XX-5026-01000-93BA-A Inspection
NOTE: T o accomplish this Service Bulletin it is necessary to use the expendable parts listed
in the subsequent referenced tasks.
Ref. AMM T ask 35-13-51-400-802
E. LIST OF EXISTING PARTS
No parts

### Page 11

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 11
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A340-A-35-XX-5026-01000-93BA-A
Inspection
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO A MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESPM 20-55-00.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including RC paragraph contained herein, contact
AIRBUS for further instructions and approval.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: The purpose of flowcharts is to supplement the information given in the Procedure and
Compliance paragraphs and not to serve as the primary source for tasks or compliance
times given in this Service Bulletin.
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
TOTAL MAN-HOURS 2.20 h
ELAPSED TIME (HOURS) 1.95 h

### Page 12

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 12
B. PREPARATION
(1) Task A340-A-35-XX-5026-01001-540A-A - Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Skills Utility
Referenced Information
Manuals/Drawings References/Sheets
AMM
T ask 12-34-24-869-002
T ask 24-41-00-861-801
T ask 52-41-00-010-801
Procedure
NOTE: For the basic Aircraft configuration, refer to AMM Chapter “Introduction -
Aircraft status for maintenance" in Manual Front Matter section.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM T ask
12-34-24-869-002.
(b) Energize the aircraft electrical circuits, refer to Ref. AMM T ask 24-41-00-861-801.
(c) Put an access platform in position below the access door Door 811.
(d) Open the access door Door 811, refer to Ref. AMM T ask 52-41-00-010-801.
C. PROCEDURE
(1) Task A340-A-35-XX-5026-01001-311A-A - Determine the applicable Inspection
Threshold
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
120
Manpower/Resources/Skills
Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Skills Utility
Referenced Information
Manuals/Drawings References/Sheets
AMM 06-20-0006-31-53
Procedure
Ref. Fig. Identification Plate Location

### Page 13

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 13
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00.
2 For the identification of frames, refer to Ref. AMM 06-31-53.
(b) Identify the component manufacturing date or maintenance/last overhaul date
given on the identification plate, refer to Ref. Fig. Identification Plate Location,
View C to select the threshold given in Accomplishment Timescale para 1.E.(2)
T able 1.
NOTE: If the placard is not readable, a review of the AIR / maintenance logs
could be an alternative to identify the P/N and S/N installed. If it is not
possible to obtain any data the unit should be handled as described for
Units with manufacture date before 2003.

### Page 14

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR9-A-002-01 SHEET 1/1
REV 00 Mar 29/19 A340-35-5026Identification Plate Location
Page 14
CONF ALL
A
FR20
FR1
132AZ
FR4
FR7
TYPICAL
POSITION OF
B
A
B
MANUFACTURING DATE
C
2HTC
5750HT
Z120
ICN-A340-A-35XX5026-A-FAPE3-00NR9-A-002-01

### Page 15

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 15
(2) Task A340-A-35-XX-5026-01001-340A-A - Do the Three Mask flow Test
WARNING: PUT A WARNING NOTICE(S) IN POSITION TO TELL PERSONS NOT
TO RELEASE THE CREW SUPPLY PUSHBUTTON SWITCH.
CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE OF THE FULL-FACE
QUICK-DONNING OXYGEN-MASK(S). YOU CAN CAUSE DAMAGE TO
THIS EQUIPMENT VERY EASILY IF YOU USE TOO MUCH FORCE OR
THE INCORRECT CLEANING MATERIALS.
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
120
Manpower/Resources/Skills
Man-hours 0.15 h
Minimum Number of person 3
Elapsed Time 0.05 h
Skills Utility
Referenced Information
Manuals/Drawings References/Sheets
AMM
06-20-00
06-31-53
T ask 12-14-35-600-801
T ask 35-00-00-860-801
T ask 35-11-41-000-801
T ask 35-11-41-400-801
Procedure
Ref. Fig. Flow Chart.
Ref. Fig. Oxygen Mask overview
Ref. Fig. Inspection report
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00.
2 For the identification of frames, refer to Ref. AMM 06-31-53.
3 Obey the special precaution when working on a gaseous oxygen system,
refer to Ref. AMM T ask 35-00-00-860-801.
4 For the oxygen storage cylinder refill procedure, refer to Ref. AMM T ask
12-14-35-600-801.
5 Remove the oxygen storage cylinder, refer to Ref. AMM T ask
35-11-41-000-801.
6 Install the oxygen storage cylinder, refer to Ref. AMM T ask
35-11-41-400-801.
(b) Prepare for the test.

### Page 16

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 16
1 Make sure that the oxygen storage cylinder, FIN 5750HT, is fully open.
NOTE: The oxygen storage cylinder should be filled with 600 PSI
minimum at the beginning of every test.
2 Make sure that the cockpit ventilation is available.
(c) Three Mask flow test.
1 Do the three mask flow test on the Captain, First Officer (F/O) and 3rd
occupant side simultaneously.
Action Result
In the cockpit, on the OXYGEN section of
the overhead control and indicating panel
211VU, push the CREW SUPPLY push-button,
refer to Ref. Fig. Oxygen Mask overview
SHEET 2, View E.
The OFF legend goes off.
Put a WARNING NOTICE in position to tell
persons not to release the CREW SUPPLY
push-button switch.
Open the DOOR/OXY page in the ECAM, refer
to Ref. Fig. Oxygen Mask overview SHEET 2,
View D.
The DOOR/QYX page is displayed on the
ECAM.
NOTE: Ensure that the REGUL LO PR
indication is not visible on the ECAM.
Open the door of the applicable crew oxygen
mask stowage box(es).
On the oxygen mask regulator hold the
oxygen mask by the red harness-inflation
control-plates and remove it from the
stowage box.
On all full-face quick-donning oxygen masks,
simultaneously turn fully the EMERGENCY
overpressure knob and start the stopwatch,
refer to Ref. Fig. Oxygen Mask overview
SHEET 2, View C.
Keep the EMERGENCY overpressure knobs
turned for 8 seconds on all masks.
During the 8 seconds, check if the REGUL LO
PR indication comes, refer to Ref. Fig. Oxygen
Mask overview SHEET 2, View D. After
the 8 seconds turn back the EMERGENCY
overpressure knobs and stop the timer.
NOTE: After each test make sure that the PRESS TO TEST/EMERGENCY
knob is not in the EMERGENCY position. If it is in the EMERGENCY
position, there can be a leak of oxygen.
2 Check the result of the test.
a If the REGUL LO PR indication on ECAM does not come up:
<1> Note down the result in accordance with Ref. Fig. Inspection
report.
<2> Upload the completed Inspection Report in accordance with Ref.
ISI 00.00.00179.

### Page 17

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 17
<3> No further action is required in accordance with this Service
Bulletin.
b If the REGUL LO PR indication comes up on ECAM:
<1> Make sure that the oxygen storage cylinder, FIN 5750HT, is fully
open.
<a> If the oxygen storage cylinder is not fully open:
[1] Fully open the oxygen storage cylinder.
[2] Repeat the three mask flow test.
<b> If the oxygen storage cylinder is fully open:
[1] Note down the result in accordance with Ref. Fig.
Inspection report.
[2] Do the two mask flow test, refer to Ref. T ask A340-
A-35-XX-5026-02ZZZ-340Z-A.

### Page 18

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR6-A-004-01 SHEET 1/1
REV 00 Mar 29/19 A340-35-5026Flow Chart
Page 18
CONF ALL
3rd OCCUPANT POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN, F/O AND
NOTE:
THE PURPOSE OF FLOW CHARTS IS TO SUPPLEMENT THE
INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE
PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE
FOR TASKS OR COMPLIANCE TIMES GIVEN IN
THIS SERVICE BULLETIN.
FOR THE COMPLIANCE TIMES, REFER TO THE
ACCOMPLISHMENT TIMESCALE PARA 1.E.(2).
POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN AND F/O
POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN 
REPLACE
THE SHUT OFF VALVE
NO FURTHER ACTION
IN ACCORDANCE WITH
THIS SERVICE BULLETIN
ENTER THE RESULT
IN THE
DO THE MASK FLOW TEST 
ON CAPTAIN, F/O AND
TEST OK?
TEST OK?
TEST OK?CYLINDERFULLY OPEN?
NO
YES
NO
NO YES
CYLINDER
FULLY
OPEN THE
INSPECTION REPORT
YES
NO
THIS SERVICE BULLETIN
PERFORM THE TSM
IN ACCORDANCE WITH
YES
3rd OCCUPANT POSITION
AT THE DETERMINED
COMPLIANCE TIME
ICN-A340-A-35XX5026-A-FAPE3-00NR6-A-004-01

### Page 19

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR7-A-001-01 SHEET 1/2
REV 00 Mar 29/19 A340-35-5026Oxygen Mask overview
Page 19
CONF ALL
A
CAPTAIN
OXYGEN
FIRST OFFICER
OXYGEN
A
VIEW LOOKING FWD
ECAM211VU
B
CC
D
E
Z210
ICN-A340-A-35XX5026-A-FAPE3-00NR7-A-001-01

### Page 20

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR8-A-001-01 SHEET 2/2
REV 00 Mar 29/19 A340-35-5026Oxygen Mask overview
Page 20
CONF ALL
TYPICAL
 OCCUPANT
OXYGEN
B
THIRD
C
C
EMERGENCY
OVERPRESSURE
KNOB
ECAM SYSTEM DISPLAY
211VU
OVERHEAD PANEL
D E
CREW SUPPLY
PUSHBOTTON
REGUL LO PR
INDICATION
ICN-A340-A-35XX5026-A-FAPE3-00NR8-A-001-01

### Page 21

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR5-A-003-01 SHEET 1/1
REV 00 Mar 29/19 A340-35-5026Inspection report
Page 21
CONF ALL
INSPECTION REPORT
SERVICE BULLETIN No. :
A/C MSN :
FLIGHT CYCLES :
FLIGHT HOURS :
A340-35-5026
DATE OF INSPECTION :
INSPECTION METHOD : SPECIAL DETAILED
INSPECTION
TABLE 1.1
PUT A CROSS (X) FOR
APPLICABLE TEST
RESULT
IF THE RESULT IS OK, REPLACE THE 
DVE90-0X VALVE AND FILL TABLE 1.2
IF THE RESULT IS OK, NO FURTHER ACTION
IF THE RESULT IS NOK, FILL THE NEXT ROW
IF THE RESULT IS NOK, FILL THE NEXT ROW
REPLACE THE 
DVE90-0X VALVE AND FILL TABLE 1.2
NEXT STEP
THREE MASKS FLOW TEST
TWO MASKS FLOW TEST
(CAPTAIN + F/O)
ONE MASK FLOW TEST
(CAPTAIN)
OK NOK
TABLE 1.2
PUT A CROSS (X) FOR
APPLICABLE TEST
RESULT
IF THE RESULT IS OK, NO FURTHER ACTION
IF THE RESULT IS NOK, PERFORM FURTHER
TROUBLE SHOOTING, 
NEXT STEP
THREE MASKS FLOW TEST
(CAPTAIN + F/O
OK NOK
NOTE:
NOK MEANS THAT THE "REGUL LO PR" INDICATION ON ECAM CAME UP DURING THE
8 SECONDS OF THE TEST
REFER TO TSM 35-10-00-810-807+ 3rd OCCUPANT)
(CAPTAIN + F/O
+ F/O + 3rd OCCUPANT)
UPLOAD THE COMPLETED INSPECTION REPORT
SHEET IN ACCORDANCE WITH ISI 00.00.00179
DETAILS OF TESTED VALVE
PART No:
SERIAL No:
DATE OF MANUFACTURE:
ICN-A340-A-35XX5026-A-FAPE3-00NR5-A-003-01

### Page 22

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 22
(3) Task A340-A-35-XX-5026-02001-340A-A - Do the Two Mask flow Test
(Depending on the Inspection Result)
WARNING: PUT A WARNING NOTICE(S) IN POSITION TO TELL PERSONS NOT
TO RELEASE THE CREW SUPPLY PUSHBUTTON SWITCH.
CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE OF THE FULL-FACE
QUICK-DONNING OXYGEN-MASK(S). YOU CAN CAUSE DAMAGE TO
THIS EQUIPMENT VERY EASILY IF YOU USE TOO MUCH FORCE OR
THE INCORRECT CLEANING MATERIALS.
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
120
Manpower/Resources/Skills
Man-hours 0.10 h
Minimum Number of person 2
Elapsed Time 0.05 h
Skills Utility
Referenced Information
Manuals/Drawings References/Sheets
AMM
06-20-00
06-31-53
T ask 12-14-35-600-801
T ask 35-00-00-860-801
T ask 35-11-41-000-801
T ask 35-11-41-400-801
Procedure
Ref. Fig. Flow Chart.
Ref. Fig. Oxygen Mask overview
Ref. Fig. Inspection report
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00.
2 For the identification of frames, refer to Ref. AMM 06-31-53.
3 Obey the special precaution when working on a gaseous oxygen system,
refer to Ref. AMM T ask 35-00-00-860-801.
4 For the Oxygen storage cylinder refill procedure, refer to Ref. AMM T ask
12-14-35-600-801.
5 Remove the oxygen storage cylinder, refer to Ref. AMM T ask
35-11-41-000-801.
6 Install the oxygen storage cylinder, refer to Ref. AMM T ask
35-11-41-400-801.
(b) Prepare for the test.

### Page 23

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 23
1 Make sure that the oxygen storage cylinder, FIN 5750HT, is fully open.
NOTE: The oxygen storage cylinder should be filled with 600 PSI
minimum at the beginning of every test.
2 Make sure that the cockpit ventilation is available.
(c) T wo Mask flow test.
1 Do the two mask flow test on the Captain and F/O side simultaneously.
Action Result
In the cockpit, on the OXYGEN section of
the overhead control and indicating panel
211VU, push the CREW SUPPLY push-button,
refer to Ref. Fig. Oxygen Mask overview
SHEET 2, View E.
The OFF legend goes off.
Put a WARNING NOTICE in position to tell
persons not to release the CREW SUPPLY
push-button switch.
Open the DOOR/OXY page in the ECAM, refer
to Ref. Fig. Oxygen Mask overview SHEET
2View D.
The DOOR/QYX page is displayed on the
ECAM.
NOTE: Ensure that the REGUL LO PR
indication is not visible on the ECAM.
Open the door of the applicable crew oxygen
mask stowage box(es).
On the oxygen mask regulator hold the
oxygen mask by the red harness-inflation
control-plates and remove it from the
stowage box.
On all full-face quick-donning oxygen masks,
simultaneously turn fully the EMERGENCY
overpressure knob and start the stopwatch,
refer to Ref. Fig. Oxygen Mask overview
SHEET 2, View C.
Keep the EMERGENCY overpressure knobs
turned for 8 seconds on all masks.
During the 8 seconds, check if the REGUL LO
PR indication comes, refer to Ref. Fig. Oxygen
Mask overview SHEET 2, View D. After
the 8 seconds turn back the EMERGENCY
overpressure knobs and stop the timer.
NOTE: After each test make sure that the PRESS TO TEST/EMERGENCY
knob is not in the EMERGENCY position. If it is in the EMERGENCY
position, there can be a leak of oxygen.
2 Check the result of the tests.
a If the REGUL LO PR indication on ECAM does not come up:
<1> Note down the result in accordance with Ref. Fig. Inspection
report.
<2> Replace the shut-off valve, refer to Ref. T ask A340-A-35-
XX-5026-01ZZZ-920Z-A.
b If the REGUL LO PR indication comes up on ECAM:

### Page 24

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 24
<1> Note down the result in accordance with Ref. Fig. Inspection
report.
<2> Do the one mask flow test, refer to Ref. T ask A340-A-35-
XX-5026-03ZZZ-340Z-A.

### Page 25

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR6-A-004-01 SHEET 1/1
REV 00 Mar 29/19 A340-35-5026Flow Chart
Page 25
CONF ALL
3rd OCCUPANT POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN, F/O AND
NOTE:
THE PURPOSE OF FLOW CHARTS IS TO SUPPLEMENT THE
INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE
PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE
FOR TASKS OR COMPLIANCE TIMES GIVEN IN
THIS SERVICE BULLETIN.
FOR THE COMPLIANCE TIMES, REFER TO THE
ACCOMPLISHMENT TIMESCALE PARA 1.E.(2).
POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN AND F/O
POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN 
REPLACE
THE SHUT OFF VALVE
NO FURTHER ACTION
IN ACCORDANCE WITH
THIS SERVICE BULLETIN
ENTER THE RESULT
IN THE
DO THE MASK FLOW TEST 
ON CAPTAIN, F/O AND
TEST OK?
TEST OK?
TEST OK?CYLINDERFULLY OPEN?
NO
YES
NO
NO YES
CYLINDER
FULLY
OPEN THE
INSPECTION REPORT
YES
NO
THIS SERVICE BULLETIN
PERFORM THE TSM
IN ACCORDANCE WITH
YES
3rd OCCUPANT POSITION
AT THE DETERMINED
COMPLIANCE TIME
ICN-A340-A-35XX5026-A-FAPE3-00NR6-A-004-01

### Page 26

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR7-A-001-01 SHEET 1/2
REV 00 Mar 29/19 A340-35-5026Oxygen Mask overview
Page 26
CONF ALL
A
CAPTAIN
OXYGEN
FIRST OFFICER
OXYGEN
A
VIEW LOOKING FWD
ECAM211VU
B
CC
D
E
Z210
ICN-A340-A-35XX5026-A-FAPE3-00NR7-A-001-01

### Page 27

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR8-A-001-01 SHEET 2/2
REV 00 Mar 29/19 A340-35-5026Oxygen Mask overview
Page 27
CONF ALL
TYPICAL
 OCCUPANT
OXYGEN
B
THIRD
C
C
EMERGENCY
OVERPRESSURE
KNOB
ECAM SYSTEM DISPLAY
211VU
OVERHEAD PANEL
D E
CREW SUPPLY
PUSHBOTTON
REGUL LO PR
INDICATION
ICN-A340-A-35XX5026-A-FAPE3-00NR8-A-001-01

### Page 28

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR5-A-003-01 SHEET 1/1
REV 00 Mar 29/19 A340-35-5026Inspection report
Page 28
CONF ALL
INSPECTION REPORT
SERVICE BULLETIN No. :
A/C MSN :
FLIGHT CYCLES :
FLIGHT HOURS :
A340-35-5026
DATE OF INSPECTION :
INSPECTION METHOD : SPECIAL DETAILED
INSPECTION
TABLE 1.1
PUT A CROSS (X) FOR
APPLICABLE TEST
RESULT
IF THE RESULT IS OK, REPLACE THE 
DVE90-0X VALVE AND FILL TABLE 1.2
IF THE RESULT IS OK, NO FURTHER ACTION
IF THE RESULT IS NOK, FILL THE NEXT ROW
IF THE RESULT IS NOK, FILL THE NEXT ROW
REPLACE THE 
DVE90-0X VALVE AND FILL TABLE 1.2
NEXT STEP
THREE MASKS FLOW TEST
TWO MASKS FLOW TEST
(CAPTAIN + F/O)
ONE MASK FLOW TEST
(CAPTAIN)
OK NOK
TABLE 1.2
PUT A CROSS (X) FOR
APPLICABLE TEST
RESULT
IF THE RESULT IS OK, NO FURTHER ACTION
IF THE RESULT IS NOK, PERFORM FURTHER
TROUBLE SHOOTING, 
NEXT STEP
THREE MASKS FLOW TEST
(CAPTAIN + F/O
OK NOK
NOTE:
NOK MEANS THAT THE "REGUL LO PR" INDICATION ON ECAM CAME UP DURING THE
8 SECONDS OF THE TEST
REFER TO TSM 35-10-00-810-807+ 3rd OCCUPANT)
(CAPTAIN + F/O
+ F/O + 3rd OCCUPANT)
UPLOAD THE COMPLETED INSPECTION REPORT
SHEET IN ACCORDANCE WITH ISI 00.00.00179
DETAILS OF TESTED VALVE
PART No:
SERIAL No:
DATE OF MANUFACTURE:
ICN-A340-A-35XX5026-A-FAPE3-00NR5-A-003-01

### Page 29

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 29
(4) Task A340-A-35-XX-5026-03001-340A-A - Do the One Mask flow Test
(Depending on the Inspection Result)
WARNING: PUT A WARNING NOTICE(S) IN POSITION TO TELL PERSONS NOT
TO RELEASE THE CREW SUPPLY PUSHBUTTON SWITCH.
CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE OF THE FULL-FACE
QUICK-DONNING OXYGEN-MASK(S). YOU CAN CAUSE DAMAGE TO
THIS EQUIPMENT VERY EASILY IF YOU USE TOO MUCH FORCE OR
THE INCORRECT CLEANING MATERIALS.
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
120
Manpower/Resources/Skills
Man-hours 0.05 h
Minimum Number of person 1
Elapsed Time 0.05 h
Skills Utility
Referenced Information
Manuals/Drawings References/Sheets
AMM
06-20-00
06-31-53
T ask 12-14-35-600-801
T ask 35-00-00-860-801
T ask 35-11-41-000-801
T ask 35-11-41-400-801
Procedure
Ref. Fig. Flow Chart.
Ref. Fig. Oxygen Mask overview
Ref. Fig. Inspection report
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00.
2 For the identification of frames, refer to Ref. AMM 06-31-53.
3 Obey the special precaution when working on a gaseous oxygen system,
refer to Ref. AMM T ask 35-00-00-860-801.
4 For the Oxygen storage cylinder refill procedure, refer to Ref. AMM T ask
12-14-35-600-801.
5 Remove the oxygen storage cylinder, refer to Ref. AMM T ask
35-11-41-000-801.
6 Install the oxygen storage cylinder, refer to Ref. AMM T ask
35-11-41-400-801.
(b) Prepare for the test.

### Page 30

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 30
1 Make sure that the oxygen storage cylinder, FIN 5750HT, is fully open.
NOTE: The oxygen storage cylinder should be filled with 600 PSI
minimum at the beginning of every test.
2 Make sure that the cockpit ventilation is available.
(c) One Mask flow test.
1 Do the one mask flow test on the Captain side.
Action Result
In the cockpit, on the OXYGEN section of
the overhead control and indicating panel
211VU, push the CREW SUPPLY push-button,
refer to Ref. Fig. Oxygen Mask overview
SHEET 2 View E.
The OFF legend goes off.
Put a WARNING NOTICE in position to tell
persons not to release the CREW SUPPLY
push-button switch.
Open the DOOR/OXY page in the ECAM, refer
to Ref. Fig. Oxygen Mask overview SHEET 2
View D.
The DOOR/QYX page is displayed on the
ECAM.
NOTE: Ensure that the REGUL LO PR
indication is not visible on the ECAM.
Open the door of the applicable crew oxygen
mask stowage box(es).
On the oxygen mask regulator hold the
oxygen mask by the red harness-inflation
control-plates and remove it from the
stowage box.
On all full-face quick-donning oxygen mask,
simultaneously turn fully the EMERGENCY
overpressure knob and start the stopwatch,
refer to Ref. Fig. Oxygen Mask overview
SHEET 2 View C.
Keep the EMERGENCY overpressure knobs
turned for 8 seconds on all masks.
During the 8 seconds, check if the REGUL LO
PR indication comes, refer to Ref. Fig. Oxygen
Mask overview SHEET 2, View D. After
the 8 seconds turn back the EMERGENCY
overpressure knobs and stop the timer.
NOTE: After each test make sure that the PRESS TO TEST/EMERGENCY
knob is not in the EMERGENCY position. If it is in the EMERGENCY
position, there can be a leak of oxygen.
2 Check the result of the tests.
a If the REGUL LO PR indication on ECAM does not come up:
<1> Note down the result in accordance with Ref. Fig. Inspection
report.
<2> Replace the shut-off valve, refer to Ref. T ask A340-A-35-
XX-5026-01ZZZ-920Z-A.
b If the REGUL LO PR indication comes up on ECAM:

### Page 31

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 31
<1> Note down the result in accordance with Ref. Fig. Inspection
report.
<2> Replace the shut-off valve, refer to Ref. T ask A340-A-35-
XX-5026-01ZZZ-920Z-A.

### Page 32

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR6-A-004-01 SHEET 1/1
REV 00 Mar 29/19 A340-35-5026Flow Chart
Page 32
CONF ALL
3rd OCCUPANT POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN, F/O AND
NOTE:
THE PURPOSE OF FLOW CHARTS IS TO SUPPLEMENT THE
INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE
PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE
FOR TASKS OR COMPLIANCE TIMES GIVEN IN
THIS SERVICE BULLETIN.
FOR THE COMPLIANCE TIMES, REFER TO THE
ACCOMPLISHMENT TIMESCALE PARA 1.E.(2).
POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN AND F/O
POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN 
REPLACE
THE SHUT OFF VALVE
NO FURTHER ACTION
IN ACCORDANCE WITH
THIS SERVICE BULLETIN
ENTER THE RESULT
IN THE
DO THE MASK FLOW TEST 
ON CAPTAIN, F/O AND
TEST OK?
TEST OK?
TEST OK?CYLINDERFULLY OPEN?
NO
YES
NO
NO YES
CYLINDER
FULLY
OPEN THE
INSPECTION REPORT
YES
NO
THIS SERVICE BULLETIN
PERFORM THE TSM
IN ACCORDANCE WITH
YES
3rd OCCUPANT POSITION
AT THE DETERMINED
COMPLIANCE TIME
ICN-A340-A-35XX5026-A-FAPE3-00NR6-A-004-01

### Page 33

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR7-A-001-01 SHEET 1/2
REV 00 Mar 29/19 A340-35-5026Oxygen Mask overview
Page 33
CONF ALL
A
CAPTAIN
OXYGEN
FIRST OFFICER
OXYGEN
A
VIEW LOOKING FWD
ECAM211VU
B
CC
D
E
Z210
ICN-A340-A-35XX5026-A-FAPE3-00NR7-A-001-01

### Page 34

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR8-A-001-01 SHEET 2/2
REV 00 Mar 29/19 A340-35-5026Oxygen Mask overview
Page 34
CONF ALL
TYPICAL
 OCCUPANT
OXYGEN
B
THIRD
C
C
EMERGENCY
OVERPRESSURE
KNOB
ECAM SYSTEM DISPLAY
211VU
OVERHEAD PANEL
D E
CREW SUPPLY
PUSHBOTTON
REGUL LO PR
INDICATION
ICN-A340-A-35XX5026-A-FAPE3-00NR8-A-001-01

### Page 35

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR5-A-003-01 SHEET 1/1
REV 00 Mar 29/19 A340-35-5026Inspection report
Page 35
CONF ALL
INSPECTION REPORT
SERVICE BULLETIN No. :
A/C MSN :
FLIGHT CYCLES :
FLIGHT HOURS :
A340-35-5026
DATE OF INSPECTION :
INSPECTION METHOD : SPECIAL DETAILED
INSPECTION
TABLE 1.1
PUT A CROSS (X) FOR
APPLICABLE TEST
RESULT
IF THE RESULT IS OK, REPLACE THE 
DVE90-0X VALVE AND FILL TABLE 1.2
IF THE RESULT IS OK, NO FURTHER ACTION
IF THE RESULT IS NOK, FILL THE NEXT ROW
IF THE RESULT IS NOK, FILL THE NEXT ROW
REPLACE THE 
DVE90-0X VALVE AND FILL TABLE 1.2
NEXT STEP
THREE MASKS FLOW TEST
TWO MASKS FLOW TEST
(CAPTAIN + F/O)
ONE MASK FLOW TEST
(CAPTAIN)
OK NOK
TABLE 1.2
PUT A CROSS (X) FOR
APPLICABLE TEST
RESULT
IF THE RESULT IS OK, NO FURTHER ACTION
IF THE RESULT IS NOK, PERFORM FURTHER
TROUBLE SHOOTING, 
NEXT STEP
THREE MASKS FLOW TEST
(CAPTAIN + F/O
OK NOK
NOTE:
NOK MEANS THAT THE "REGUL LO PR" INDICATION ON ECAM CAME UP DURING THE
8 SECONDS OF THE TEST
REFER TO TSM 35-10-00-810-807+ 3rd OCCUPANT)
(CAPTAIN + F/O
+ F/O + 3rd OCCUPANT)
UPLOAD THE COMPLETED INSPECTION REPORT
SHEET IN ACCORDANCE WITH ISI 00.00.00179
DETAILS OF TESTED VALVE
PART No:
SERIAL No:
DATE OF MANUFACTURE:
ICN-A340-A-35XX5026-A-FAPE3-00NR5-A-003-01

### Page 36

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 36
(5) Task A340-A-35-XX-5026-01001-920A-A - Replace the Shut off Valve
(Depending on the Inspection Result)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
120 Work location From Frame 1 to Frame 4
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Skills Airframe
Material necessary to do the job
Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
DVE90-06 1 VALVE
DVE90-07 1 VALVE
Referenced Information
Manuals/Drawings References/Sheets
AMM
06-20-00
06-31-53
T ask 12-14-35-600-801
T ask 35-00-00-860-801
T ask 35-11-41-000-801
T ask 35-11-41-400-801
T ask 35-13-51-000-801
T ask 35-13-51-400-802
Procedure
Refer to Ref. Fig. Flow Chart.
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00.
2 For the identification of frames, refer to Ref. AMM 06-31-53.
3 Obey the special precaution when working on a gaseous oxygen system,
refer to Ref. AMM T ask 35-00-00-860-801.
4 For the oxygen storage cylinder refill procedure, refer to Ref. AMM T ask
12-14-35-600-801.
5 Remove the oxygen storage cylinder, refer to Ref. AMM T ask
35-11-41-000-801.
6 Install the oxygen storage cylinder, refer to Ref. AMM T ask
35-11-41-400-801.
(b) Replace the Shut off Valve.
1 Remove, in accordance with Ref. AMM T ask 35-13-51-000-801:
FIN 2HT
1 VALVE-SOLENOID DVE90-06   Retain

### Page 37

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 37
or
FIN 2HT
1 VALVE-SOLENOID DVE90-07   Retain
2 Install, in accordance with Ref. AMM T ask 35-13-51-400-802:
FIN 2HT
1 VALVE-SOLENOID DVE90-06  
or
FIN 2HT
1 VALVE-SOLENOID DVE90-07  
(c) Do the leak test and electrical test, in accordance with Ref. AMM T ask
35-13-51-400-802.
(d) Send the retained shut off valve back to ZODIAC for repair, at the address given
below:
NOTE: Request in the repair order to record the incoming pressure drop value
on Shop Finding Report.
ZODIAC
ZODIAC Aerospace Services Americas
6734 Valjean Avenus
CA 91406 Van Nuys
USA
Phone: +33 970 830 830
E-mail: csr.americas@zodiacaerospace.com

### Page 38

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR6-A-004-01 SHEET 1/1
REV 00 Mar 29/19 A340-35-5026Flow Chart
Page 38
CONF ALL
3rd OCCUPANT POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN, F/O AND
NOTE:
THE PURPOSE OF FLOW CHARTS IS TO SUPPLEMENT THE
INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE
PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE
FOR TASKS OR COMPLIANCE TIMES GIVEN IN
THIS SERVICE BULLETIN.
FOR THE COMPLIANCE TIMES, REFER TO THE
ACCOMPLISHMENT TIMESCALE PARA 1.E.(2).
POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN AND F/O
POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN 
REPLACE
THE SHUT OFF VALVE
NO FURTHER ACTION
IN ACCORDANCE WITH
THIS SERVICE BULLETIN
ENTER THE RESULT
IN THE
DO THE MASK FLOW TEST 
ON CAPTAIN, F/O AND
TEST OK?
TEST OK?
TEST OK?CYLINDERFULLY OPEN?
NO
YES
NO
NO YES
CYLINDER
FULLY
OPEN THE
INSPECTION REPORT
YES
NO
THIS SERVICE BULLETIN
PERFORM THE TSM
IN ACCORDANCE WITH
YES
3rd OCCUPANT POSITION
AT THE DETERMINED
COMPLIANCE TIME
ICN-A340-A-35XX5026-A-FAPE3-00NR6-A-004-01

### Page 39

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 39
(6) Task A340-A-35-XX-5026-04001-340A-A - Do the Three Mask flow Test after
replacement of the Shut off Valve
WARNING: PUT A WARNING NOTICE(S) IN POSITION TO TELL PERSONS NOT
TO RELEASE THE CREW SUPPLY PUSHBUTTON SWITCH.
CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE OF THE FULL-FACE
QUICK-DONNING OXYGEN-MASK(S). YOU CAN CAUSE DAMAGE TO
THIS EQUIPMENT VERY EASILY IF YOU USE TOO MUCH FORCE OR
THE INCORRECT CLEANING MATERIALS.
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
120
Manpower/Resources/Skills
Man-hours 0.15 h
Minimum Number of person 3
Elapsed Time 0.05 h
Skills Utility
Referenced Information
Manuals/Drawings References/Sheets
AMM
06-20-00
06-31-53
T ask 12-14-35-600-801
T ask 35-00-00-860-801
T ask 35-11-41-000-801
T ask 35-11-41-400-801
TSM T ask 35-10-00-810-807
Procedure
Ref. Fig. Flow Chart.
Ref. Fig. Oxygen Mask overview
Ref. Fig. Inspection report
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00.
2 For the identification of frames, refer to Ref. AMM 06-31-53.
3 Obey the special precaution when working on a gaseous oxygen system,
refer to Ref. AMM T ask 35-00-00-860-801.
4 For the oxygen storage cylinder refill procedure, refer to Ref. AMM T ask
12-14-35-600-801.
5 Remove the oxygen storage cylinder, refer to Ref. AMM T ask
35-11-41-000-801.
6 Install the oxygen storage cylinder, refer to Ref. AMM T ask
35-11-41-400-801.
(b) Prepare for the test.

### Page 40

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 40
1 Make sure that the oxygen storage cylinder, FIN 5750HT, is fully open.
NOTE: The oxygen storage cylinder should be filled with 600 PSI
minimum at the beginning of every test.
2 Make sure that the cockpit ventilation is available.
(c) Three Mask flow test.
1 Do the three mask flow test on the Captain, First Officer (F/O) and third
occupant side simultaneously.
Action Result
In the cockpit, on the OXYGEN section of
the overhead control and indicating panel
211VU, push the CREW SUPPLY push-button,
refer to Ref. Fig. Oxygen Mask overview
SHEET 2, View E.
The OFF legend goes off.
Put a WARNING NOTICE in position to tell
persons not to release the CREW SUPPLY
push-button switch.
Open the DOOR/OXY page in the ECAM, refer
to Ref. Fig. Oxygen Mask overview SHEET
2View D.
The DOOR/QYX page is displayed on the
ECAM.
NOTE: Ensure that the REGUL LO PR
indication is not visible on the ECAM.
Open the door of the applicable crew oxygen
mask stowage box(es).
On the oxygen mask regulator hold the
oxygen mask by the red harness-inflation
control-plates and remove it from the
stowage box.
On all full-face quick-donning oxygen mask,
simultaneously turn fully the EMERGENCY
overpressure knob and start the stopwatch,
refer to Ref. Fig. Oxygen Mask overview
SHEET 2, View C.
Keep the EMERGENCY overpressure knobs
turned for 8 seconds on all masks.
During the 8 seconds, check if the REGUL LO
PR indication comes, refer to Ref. Fig. Oxygen
Mask overview SHEET 2, View D. After
the 8 seconds turn back the EMERGENCY
overpressure knobs and stop the timer.
NOTE: After each test make sure that the PRESS TO TEST/EMERGENCY
knob is not in the EMERGENCY position. If it is in the EMERGENCY
position, there can be a leak of oxygen.
2 Check the result of the test.
a If the REGUL LO PR indication on ECAM does not come up:
<1> Note down the result in accordance with Ref. Fig. Inspection
report.
<2> Upload the completed Inspection Report in accordance with Ref.
ISI 00.00.00179.

### Page 41

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 41
<3> No further action is required in accordance with this Service
Bulletin.
b If the REGUL LO PR indication comes up on ECAM:
<1> Note down the result in accordance with Ref. Fig. Inspection
report.
<2> Upload the completed Inspection Report in accordance with Ref.
ISI 00.00.00179.
<3> Do the trouble shooting in accordance with Ref. TSM T ask
35-10-00-810-807.

### Page 42

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR6-A-004-01 SHEET 1/1
REV 00 Mar 29/19 A340-35-5026Flow Chart
Page 42
CONF ALL
3rd OCCUPANT POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN, F/O AND
NOTE:
THE PURPOSE OF FLOW CHARTS IS TO SUPPLEMENT THE
INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE
PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE
FOR TASKS OR COMPLIANCE TIMES GIVEN IN
THIS SERVICE BULLETIN.
FOR THE COMPLIANCE TIMES, REFER TO THE
ACCOMPLISHMENT TIMESCALE PARA 1.E.(2).
POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN AND F/O
POSITION
DO THE MASK FLOW TEST 
ON CAPTAIN 
REPLACE
THE SHUT OFF VALVE
NO FURTHER ACTION
IN ACCORDANCE WITH
THIS SERVICE BULLETIN
ENTER THE RESULT
IN THE
DO THE MASK FLOW TEST 
ON CAPTAIN, F/O AND
TEST OK?
TEST OK?
TEST OK?CYLINDERFULLY OPEN?
NO
YES
NO
NO YES
CYLINDER
FULLY
OPEN THE
INSPECTION REPORT
YES
NO
THIS SERVICE BULLETIN
PERFORM THE TSM
IN ACCORDANCE WITH
YES
3rd OCCUPANT POSITION
AT THE DETERMINED
COMPLIANCE TIME
ICN-A340-A-35XX5026-A-FAPE3-00NR6-A-004-01

### Page 43

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR7-A-001-01 SHEET 1/2
REV 00 Mar 29/19 A340-35-5026Oxygen Mask overview
Page 43
CONF ALL
A
CAPTAIN
OXYGEN
FIRST OFFICER
OXYGEN
A
VIEW LOOKING FWD
ECAM211VU
B
CC
D
E
Z210
ICN-A340-A-35XX5026-A-FAPE3-00NR7-A-001-01

### Page 44

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR8-A-001-01 SHEET 2/2
REV 00 Mar 29/19 A340-35-5026Oxygen Mask overview
Page 44
CONF ALL
TYPICAL
 OCCUPANT
OXYGEN
B
THIRD
C
C
EMERGENCY
OVERPRESSURE
KNOB
ECAM SYSTEM DISPLAY
211VU
OVERHEAD PANEL
D E
CREW SUPPLY
PUSHBOTTON
REGUL LO PR
INDICATION
ICN-A340-A-35XX5026-A-FAPE3-00NR8-A-001-01

### Page 45

A340-500/600
SERVICE BULLETIN
Figure ICN-A340-A-35XX5026-A-FAPE3-00NR5-A-003-01 SHEET 1/1
REV 00 Mar 29/19 A340-35-5026Inspection report
Page 45
CONF ALL
INSPECTION REPORT
SERVICE BULLETIN No. :
A/C MSN :
FLIGHT CYCLES :
FLIGHT HOURS :
A340-35-5026
DATE OF INSPECTION :
INSPECTION METHOD : SPECIAL DETAILED
INSPECTION
TABLE 1.1
PUT A CROSS (X) FOR
APPLICABLE TEST
RESULT
IF THE RESULT IS OK, REPLACE THE 
DVE90-0X VALVE AND FILL TABLE 1.2
IF THE RESULT IS OK, NO FURTHER ACTION
IF THE RESULT IS NOK, FILL THE NEXT ROW
IF THE RESULT IS NOK, FILL THE NEXT ROW
REPLACE THE 
DVE90-0X VALVE AND FILL TABLE 1.2
NEXT STEP
THREE MASKS FLOW TEST
TWO MASKS FLOW TEST
(CAPTAIN + F/O)
ONE MASK FLOW TEST
(CAPTAIN)
OK NOK
TABLE 1.2
PUT A CROSS (X) FOR
APPLICABLE TEST
RESULT
IF THE RESULT IS OK, NO FURTHER ACTION
IF THE RESULT IS NOK, PERFORM FURTHER
TROUBLE SHOOTING, 
NEXT STEP
THREE MASKS FLOW TEST
(CAPTAIN + F/O
OK NOK
NOTE:
NOK MEANS THAT THE "REGUL LO PR" INDICATION ON ECAM CAME UP DURING THE
8 SECONDS OF THE TEST
REFER TO TSM 35-10-00-810-807+ 3rd OCCUPANT)
(CAPTAIN + F/O
+ F/O + 3rd OCCUPANT)
UPLOAD THE COMPLETED INSPECTION REPORT
SHEET IN ACCORDANCE WITH ISI 00.00.00179
DETAILS OF TESTED VALVE
PART No:
SERIAL No:
DATE OF MANUFACTURE:
ICN-A340-A-35XX5026-A-FAPE3-00NR5-A-003-01

### Page 46

A340-500/600
SERVICE BULLETIN
REV 00 Mar 29/19 A340-35-5026
Page 46
D. PREPARATION FOR TEST
None
E. TEST
None
F. CLOSE-UP
(1) Task A340-A-35-XX-5026-01001-740A-A - Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
AMM
T ask 35-12-41-420-059
T ask 35-13-51-400-802
T ask 52-41-00-410-810
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Do the close up procedure in accordance with Ref. AMM T ask 35-13-51-400-802.
(c) Re-store the oxygen mask(s) in the stowage box(es), refer to Ref. AMM T ask
35-12-41-420-059.
(d) On the Electrical Panel 211VU release the OXYGEN/CREW SUPPLY push-button
switch.
(e) Close the access door Door 811, refer to Ref. AMM T ask 52-41-00-410-810.
(f) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A340-A-35-XX-5026-01001-90AA-A - Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 47

A340-500/600
SERVICE BULLETIN
APPENDIX
REV 00 Mar 29/19 A340-35-5026
Page 47
APPENDIX
A. REPORTING SHEET
TITLE: OXYGEN - CREW OXYGEN - INSPECTION OF THE OXYGEN SUPPLY
SOLENOID VALVE
MODIFICATION No.:  
(1) SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance
and Flight Operations Products if it is duly reported to Airbus.
(2) GENERAL information
The SB Reporting policy is published in ISI 00.00.00135. This document provides
information regarding: the SB Reporting means and benefits, the update of
customized Maintenance Products and customized Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations
Products" for further information on the update of affected Flight Operations Products.
(3) SB Reporting procedure
Standard practice to report SB is to use the online reporting application on
AirbusWorld.
Refer to ISI 00.00.00179:
- For complete information on reporting means to Airbus, Question 2 "What are
the standard practices for SB Reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs,
Question 3 "What about the reporting of prerequisite Service Bulletins?"
NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.

### Page 48

A340-500/600
SERVICE BULLETIN
APPENDIX
REV 00 Mar 29/19 A340-35-5026
Page 48
B. QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin.
The reported data that you provide us will be used to analyse areas of difficulties and to
take corrective action to further improve the quality of our Service Bulletin.
We thank you for the time you have taken in completing this form.
Quality rating of this SB 4 3 2 1
Quality rating of the Accomplishment Instructions 4 3 2 1
Quality rating of the Illustrations 4 3 2 1
Is this SB easy to understand ? Y / N
NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score
If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.
Planning Material Instructions
X Applicability X T ooling X Preparation
X Reason X List of Materials
Operator Supplied
X Mod/Inspection
X Manpower X Kit content X T est
X References X Re-identification X Close-up
X Publication X Illustrations
X Industry Support
Comments :
Operator : Date :
Name/Title
Please return this form to :
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
Or via your Resident Customer Support Office.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
