# Airbus Service Bulletin A340-57-4139

Copy: No revision named ("A340-57-4139 R00"), 139 pages: PDF https://openairdocs.org/files/sha256/b5/09/b5098249aff1c6ffa7f7117821405b6cf5f854e64aea554149e17508c3d2b501; text https://openairdocs.org/service-documents/airbus/a340-57-4139/file/b5098249aff1.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2018-0113, the docket of AD 2019-16-07. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A340-57-4139
- Page: https://openairdocs.org/service-documents/airbus/a340-57-4139

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus/a340-57-4139/proposed.md).

## Text (139 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2018-0113, the docket of AD 2019-16-07. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

@A340
SERVICE BULLETIN
SUMMARY
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
This summary is for information only and is not approved for modification of the aircraft.
ATA SYSTEM: 57
TITLE: FUSELAGE - CENTER FUSELAGE - MODIFICATION OF FASTENER
HOLES NO 25,38,39 and 43 AT FRAME 40 VERTICAL WEB BELOW
CENTER WING BOX LOWER PANEL
**CONF ALL
MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR
 206048S33788
MINOR
 None
NOTE
: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting the
airworthiness of the product. All other changes are major changes.
REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
The area at Frame (FR) 40 is subjected to a specific maintenance program. A new campaign of
modifications has been launched to improve the maintenance program, decrease the number of
maintenance actions and to improve the structural potential of the aircraft to meet the Extended Service
Goal (ESG)/Design Service Goal (DSG).
This Service Bulletin recommends the application of Cold Working on holes 25, 38, 39 and 43 at FR40
to improve the fatigue behaviour.
Depending on the configuration, this reinforcement consists in doing a first or second cold expansion of
fastener holes 25, 38, 39 and 43 and installing oversized fastener with high interference.
Accomplishment of this Service Bulletin will contribute to prevent cracks and will increase the fatigue life
in the area of FR40.
Depending on configuration, accomplishment of this Service Bulletin cancels the requirements of
Inspection Service Bulletin No. A340-57-4125 for holes 25, 38, 39 and 43, if accomplished after the
lower bound described in Inspection Service Bulletin No. A340-57-4125. For hole 25, for Aircraft in Conf
004 and 005, this modification Service Bulletin is not terminative and must be monitored by Inspection
Service Bulletin No. A340-57-4125.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 1
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 2

@A340
SERVICE BULLETIN
SUMMARY
GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE
 RECOMMENDED (1)
 CANCELS INSPECTION SB
 NO
POTENTIAL AD
 NO
 A/C OPERATION AFFECTED
 NO
RELIABILITY AFFECTED
 NO
 PAX COMFORT AFFECTED
 NO
COST SAVING
 NO
 LROPS AFFECTED
 NO
STRUCTURAL LIFE EXTN
 NO
 VENDOR SB INVOLVED
 NO
NOTE
 (1)
: Service Bulletin recommended to be accomplished to prevent significant operational
disruptions.
MATERIAL PRICE INFORMATION
**CONF 001
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET
 QTY PER
A/C
PRICE PER
A/C (USD)
MAIN PARTS
Kit 574139A01R01
 1
 120.00
 Bolts, Nuts
Kit 574139A02R00
 1
 50.00
 Bolts, Nuts
TOTAL
 170.00
Standard tool TOOLA01
 1
 See SB
 Durable Tool Kit
Standard tool TOOLA02
 1
 See SB
 Expendable Tool Kit
**CONF 002
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET
 QTY PER
A/C
PRICE PER
A/C (USD)
MAIN PARTS
Kit 574139A01R01
 1
 120.00
 Bolts, Nuts
Standard tool TOOLA01
 1
 See SB
 Durable Tool Kit
Standard tool TOOLA02
 1
 See SB
 Expendable Tool Kit
**CONF 003
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET
 QTY PER
A/C
PRICE PER
A/C (USD)
MAIN PARTS
Kit 574139A01R01
 1
 120.00
 Bolts, Nuts
Kit 574139A02R00
 1
 50.00
 Bolts, Nuts
TOTAL
 170.00
Standard tool TOOLA01
 1
 See SB
 Durable Tool Kit
Standard tool TOOLA02
 1
 See SB
 Expendable Tool Kit
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 2
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 3

@A340
SERVICE BULLETIN
SUMMARY
**CONF 004
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET
 QTY PER
A/C
PRICE PER
A/C (USD)
MAIN PARTS
Kit 574139A01R01
 1
 120.00
 Bolts, Nuts
Kit 574139A02R00
 1
 50.00
 Bolts, Nuts
TOTAL
 170.00
Standard tool TOOLA01
 1
 See SB
 Durable Tool Kit
Standard tool TOOLA02
 1
 See SB
 Expendable Tool Kit
EFFECTIVITY
**CONF ALL
This Service Bulletin is applicable to this (these) operator(s) :
09M 83V ABD ACA AFR AIB ALD ARG AXY BEK BOE CAL CPA
DLH EDW F2I FIN GAF HFM HFY IBE IRM LAN MAU MDG MRJ
O2X PAL PUE QAF ROI S3R SAA SAS SLM SVW SWR THT THY
UAE
CONCURRENT REQUIREMENTS
None
REFERENCES / REPERCUSSIONS
TFU
 57.11.00.007
OEB
 None
AOT
 None
SIL
 None
ISI
 None
LINE MAINTENANCE AFFECTED
 No
LIFE LIMIT
 None
OTHER
 None
NATURE OF THE WORK
AIRCRAFT
 YES
EQUIPMENT
 NO
HARD
 NO
SOFT
 NO
OBRM
 NO
MANPOWER
**CONF 001
Task 574139-831-801-001: Modification
TOTAL MANHOURS
 29.00
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 3
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 4

@A340
SERVICE BULLETIN
SUMMARY
Task 574139-831-801-001: Modification
ELAPSED TIME (HOURS)
 14.75
**CONF 002
Task 574139-831-801-001: Modification
TOTAL MANHOURS
 26.50
ELAPSED TIME (HOURS)
 13.50
**CONF 003
Task 574139-831-801-001: Modification
TOTAL MANHOURS
 29.00
ELAPSED TIME (HOURS)
 14.75
**CONF 004
Task 574139-831-801-001: Modification
TOTAL MANHOURS
 29.00
ELAPSED TIME (HOURS)
 14.75
APPENDICES
**CONF ALL
Appendix 01 - Manpower Gantt Chart
Appendix 02 - Configuration Definition table
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 4
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 5

@A340
SERVICE BULLETIN
SUMMARY
**CONF 001, 003 thru 004
VIEW LOOKING AFT
RH SHOWN
LH SYMMETRICAL
BU
P
INBD
CENTER WING BOX
LOWER PANEL REFERENCE
COLD WORKING OF
4 FASTENER HOLES
Z140
A
FR40
STGR39RH
STGR38RH
H25 H38 H39
H43
A
FR47
FR40
B
F_SB_574139_5_SAAA_01_03
Figure A-FSAAA - Sheet 01
Cold Working of the Fasteners Holes 25, 38, 39 and 43
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 5
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 6

@A340
SERVICE BULLETIN
SUMMARY
**CONF 002
VIEW LOOKING AFT
RH SHOWN
LH SYMMETRICAL
BU
P
INBD
CENTER WING BOX
LOWER PANEL REFERENCE
COLD WORKING OF
3 FASTENER HOLES
Z140
A
FR40
STGR39RH
STGR38RH
H38 H39
H43
A
FR47
FR40
B
F_SB_574139_5_SAAB_01_03
Figure A-FSAAB - Sheet 01
Cold Working of the Fasteners Holes 38, 39 and 43
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 6
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 7

@A340
SERVICE BULLETIN
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
ATA SYSTEM: 57
TITLE: FUSELAGE - CENTER FUSELAGE - MODIFICATION OF FASTENER
HOLES NO 25,38,39 and 43 AT FRAME 40 VERTICAL WEB BELOW
CENTER WING BOX LOWER PANEL
MODIFICATION No.: 206048S33788
This document contains AIRBUS PROPRIETARY INFORMATION and shall at all times remain the
property of AIRBUS; no intellectual property right or licence is granted by AIRBUS in connection with
any information contained in it. It is delivered on the express condition that said document and the
information contained in it shall be treated as confidential, shall not be used for any purpose other than
that for which it is hereby delivered. It shall not be disclosed in whole or in part to third parties and shall
not be duplicated in any manner (except for the purposes of performing the tasks described hereunder
and provided that any recipient of such document shall comply with the conditions herein), without
AIRBUS prior written consent.
1. PLANNING INFORMATION
**CONF ALL
A. EFFECTIVITY
NOTE
: This modification is applicable by Service Bulletin only.
NOTE
: This Service Bulletin is only applicable to aircraft on which MOD No.
44360S13013 or MOD No. 44360S13482 is embodied.
(1) Models
340-212 340-213 340-312 340-313
(2) Effectivity by MSN
0178-0180 0185-0186 0190 0192-0194 0197 0199 0201-0202 0204 0207-0208 0210
0212-0215 0217-0218 0220-0221 0227-0228 0233 0236-0237 0242-0243 0245-0246
0252 0257 0260 0263-0264 0268 0270 0273-0274 0278 0280 0282 0292 0297 0302
0304 0307 0310 0318-0319 0321 0325 0327 0329 0331-0332 0335 0347 0352
0354-0355 0363 0367 0373-0374 0377-0379 0381 0385 0387 0390 0395 0399 0402
0406 0411 0413 0415 0424 0430 0433-0435 0438 0446-0447 0450 0459 0467 0470
0474 0483 0528 0538 0541 0544-0546 0554 0556 0559 0561-0562 0582 0585 0590
0598 0643 0646 0651 0668 0793 0800 0835 0844 0921 0938 0955
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 1
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 8

@A340
SERVICE BULLETIN
(3) Effectivity by Operator
The Operator/MSN relationship is provided for information only and is correct at the time
of issue in accordance with the information available to AIRBUS. Any future changes
resulting from transfer of an aircraft from one operator to another will not be reflected in
this list unless the Service Bulletin is revised for another reason.
OPERATOR
 MSN
09M
 0483
83V
 0280 0292
ABD
 0210
ACA
 0278
AFR
 0186 0207 0237 0245 0246 0260 0307 0310 0377 0399
AIB
 0192 0243 0264
ALD
 0178
ARG
 0193 0373
AXY
 0374
BEK
 0381
BOE
 0554
CAL
 0402 0406 0411 0415 0433 0541
CPA
 0208 0218 0220 0227 0228
DLH
 0213 0233 0252 0297 0304 0321 0325 0327 0335 0347 0352 0354
0379 0390 0434 0447
EDW
 0562
F2I
 0214
FIN
 0835 0844 0921 0938
GAF
 0274 0355
HFM
 0367
HFY
 0190 0202
IBE
 0217 0221 0329
IRM
 0282
LAN
 0363
MAU
 0194 0268 0793 0800
MDG
 0319
MRJ
 0257
O2X
 0273
PAL
 0302 0318 0332 0387 0459 0474
PUE
 0212 0215
QAF
 0528
ROI
 0199 0201
S3R
 0204
SAA
 0197 0378 0544 0582 0590 0643 0646 0651
SAS
 0413 0424 0430 0435 0450 0467 0470
SLM
 0242
SVW
 0955
SWR
 0179 0263 0538 0545 0546 0556 0559 0561 0585 0598
THT
 0385 0395 0438 0446 0668
THY
 0180 0270 0331
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 2
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 9

@A340
SERVICE BULLETIN
OPERATOR
 MSN
UAE
 0185 0236
(4) Configuration by MSN
MSN
 CONFIGURATION
0178 0180 0185 0190 0192 0199 0201 0202 0204 0212 0214
0215 0236 0242 0243 0257 0264 0270 0273 0278 0280 0282
0292 0318 0319 0331 0363 0373 0378 0385 0395 0413 0424
0430 0435 0438 0446 0450 0467 0470
001 002
0179 0186 0193 0194 0197 0207 0208 0210 0213 0217 0218
0220 0221 0227 0228 0233 0237 0245 0246 0252 0260 0263
0268 0274 0297 0302 0304 0307 0310 0321 0325 0327 0329
0332 0335 0347 0352 0354 0355 0367 0374 0377 0379 0381
0387 0390 0399 0402 0406 0411 0415 0433 0434 0447 0459
0474 0483 0538
002
0528 0541
 002 003
0544 0545 0546 0554 0556 0559 0561 0562 0582 0585 0590
0598 0643 0646 0651 0668 0793 0800
003
0835 0844 0921 0938 0955
 004
(5) Configuration definition
The following table gives further information of the Configuration Definition.
**CONF 001
Config 001 is valid for aircraft on which:
- MOD No. 49202S16307 is not embodied
- Service Bulletin No. A330-57-4090 is not accomplished.
**CONF 002
Config 002 is valid for aircraft on which:
- MOD No. 49202S16307 is not embodied
- Service Bulletin No. A330-57-4090 is accomplished.
**CONF 003
Config 003 is valid for aircraft on which:
- MOD No. 49202S16307 is embodied
- MOD No. 55306S18660 is not embodied.
**CONF 004
Config 004 is valid for aircraft on which:
- MOD No. 49202S16307 is embodied
- MOD No. 55306S18660 is embodied.
For further information concerning the Configuration Definition, refer to Appendix 02 -
Configuration Definition table .
(6) Material Effectivity
NOTE
: Only 1 TOOL Kit is necessary to perform the Cold Working, either
TOOLA01 or TOOLA02 depending on the supplier chosen.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 3
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 10

@A340
SERVICE BULLETIN
**CONF 001, 003 thru 004
MATERIAL
 QTY PER A/C
 SEE NOTES
Kit 574139A01R01
 1
Kit 574139A02R00
 1
Consumable CMLA01
 1
Standard tool TOOLA01
 1
Standard tool TOOLA02
 1
**CONF 002
MATERIAL
 QTY PER A/C
 SEE NOTES
Kit 574139A01R01
 1
Consumable CMLA01
 1
Standard tool TOOLA01
 1
Standard tool TOOLA02
 1
**CONF ALL
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
The area at Frame (FR) 40 is subjected to a specific maintenance program. A new
campaign of modifications has been launched to improve the maintenance program,
decrease the number of maintenance actions and to improve the structural potential of
the aircraft to meet the Extended Service Goal (ESG)/Design Service Goal (DSG).
(2) Objective/Action
This Service Bulletin recommends the application of Cold Working on holes 25, 38, 39
and 43 at FR40 to improve the fatigue behaviour.
Depending on the configuration, this reinforcement consists in doing a first or second
cold expansion of fastener holes 25, 38, 39 and 43 and installing oversized fastener with
high interference.
(3) Advantages
Accomplishment of this Service Bulletin will contribute to prevent cracks and will
increase the fatigue life in the area of FR40.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 4
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 11

@A340
SERVICE BULLETIN
(4) Operational/Maintenance Consequences
Depending on configuration, accomplishment of this Service Bulletin cancels the
requirements of Inspection Service Bulletin No. A340-57-4125 for holes 25, 38, 39 and
43, if accomplished after the lower bound described in Inspection Service Bulletin No.
A340-57-4125. For hole 25, for Aircraft in Conf 004 and 005, this modification Service
Bulletin is not terminative and must be monitored by Inspection Service Bulletin No.
A340-57-4125.
D. DESCRIPTION
To accomplish this Service Bulletin it is necessary to :
**CONF 001
Task 574139-831-801-001: Modification
(1) Remove the Fastener at the Holes 25, 38, 39 and 43 between STGR38 and STGR40
at FR40 on the LH side
(2) Do an Inspection of the fastener at the Holes 25, 38, 39 and 43 between STGR38
and STGR40 at FR40 on the LH side
(3) Do a Cold Working of the fastener Holes 25, 38, 39 and 43 between STGR38 and
STGR40 at FR40 on the LH side
(4) Install the fastener at the Holes 25, 38, 39 and 43 between STGR38 and STGR40 at
FR40 on the LH side
(5) Remove the fastener at the Holes 25, 38, 39 and 43 between STGR38 and STGR40
at FR40 on the RH side
(6) Do an Inspection of the fastener at the Holes 25, 38, 39 and 43 between STGR38
and STGR40 at FR40 on the RH side
(7) Do a Cold Working of the fastener Holes 25, 38, 39 and 43 between STGR38 and
STGR40 at FR40 on the RH side
(8) Install the fastener at the Holes 25, 38, 39 and 43 between STGR38 and STGR40 at
FR40 on the RH side
**CONF 002
Task 574139-831-801-001: Modification
(1) Remove the Fastener at the Holes 38, 39 and 43 between STGR38 and STGR40 at
FR40 on the LH side
(2) Do an Inspection of the Fastener at the Holes 38, 39 and 43 between STGR38 and
STGR40 at FR40 on the LH side
(3) Do a Cold Working of the fastener Holes 38, 39 and 43 between STGR38 and
STGR40 at FR40 on the LH side
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 5
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 12

@A340
SERVICE BULLETIN
(4) Install the fastener at the Holes 38, 39 and 43 between STGR38 and STGR40 at
FR40 on the LH side
(5) Remove the fastener at the Holes 38, 39 and 43 between STGR38 and STGR40 at
FR40 on the RH side
(6) Do an Inspection of the fastener at the Holes 38, 39 and 43 between STGR38 and
STGR40 at FR40 on the RH side
(7) Do a Cold Working of the fastener Holes 38, 39 and 43 between STGR38 and
STGR40 at FR40 on the RH side
(8) Install the fastener at the Holes 38, 39 and 43 between STGR38 and STGR40 at
FR40 on the RH side
**CONF 003
Task 574139-831-801-001: Modification
(1) Remove the Fastener at the Holes 25, 38, 39 and 43 between STGR38 and STGR40
at FR40 on the LH side
(2) Do an Inspection of the fastener at the Holes 25, 38, 39 and 43 between STGR38
and STGR40 at FR40 on the LH side
(3) Do a Cold Working of the fastener Holes 25, 38, 39 and 43 between STGR38 and
STGR40 at FR40 on the LH side
(4) Install the fastener at the Holes 25, 38, 39 and 43 between STGR38 and STGR40 at
FR40 on the LH side
(5) Remove the fastener at the Holes 25, 38, 39 and 43 between STGR38 and STGR40
at FR40 on the RH side
(6) Do an Inspection of the fastener at the Holes 25, 38, 39 and 43 between STGR38
and STGR40 at FR40 on the RH side
(7) Do a Cold Working of the fastener Holes 25, 38, 39 and 43 between STGR38 and
STGR40 at FR40 on the RH side
(8) Install the fastener at the Holes 25, 38, 39 and 43 between STGR38 and STGR40 at
FR40 on the RH side
**CONF 004
Task 574139-831-801-001: Modification
(1) Remove the Fastener at the Holes 25, 38, 39 and 43 between STGR38 and STGR40
at FR40 on the LH side
(2) Do an Inspection of the fastener at the Holes 25, 38, 39 and 43 between STGR38
and STGR40 at FR40 on the LH side
(3) Do a Cold Working of the fastener Holes 25, 38, 39 and 43 between STGR38 and
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 6
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 13

@A340
SERVICE BULLETIN
STGR40 at FR40 on the LH side
(4) Install the fastener at the Holes 25, 38, 39 and 43 between STGR38 and STGR40 at
FR40 on the LH side
(5) Remove the fastener at the Holes 25, 38, 39 and 43 between STGR38 and STGR40
at FR40 on the RH side
(6) Do an Inspection of the fastener at the Holes 25, 38, 39 and 43 between STGR38
and STGR40 at FR40 on the RH side
(7) Do a Cold Working of the fastener Holes 25, 38, 39 and 43 between STGR38 and
STGR40 at FR40 on the RH side
(8) Install the fastener at the Holes 25, 38, 39 and 43 between STGR38 and STGR40 at
FR40 on the RH side
**CONF ALL
E. COMPLIANCE
(1) Classification
RECOMMENDED: Service Bulletin recommended to be accomplished to prevent
significant operational disruptions.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin is recommended at the earliest opportunity
where manpower and facilities are available.
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the effectivity has a modification or repair embodied that is not of
AIRBUS origin, and which affects the content of this Service Bulletin, the operator is
responsible for obtaining approval by its airworthiness authority for any adaptation necessary
before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also not
included.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 7
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 14

@A340
SERVICE BULLETIN
**CONF 001
Task 574139-831-801-001: Modification
Get Access
 10.00
On Aircraft
Remove the Fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the LH
side
0.75
Do an Inspection of the fastener at the Holes 25, 38,
39 and 43 between STGR38 and STGR40 at FR40 on
the LH side
0.75
Do a Cold Working of the fastener Holes 25, 38, 39
and 43 between STGR38 and STGR40 at FR40 on the
LH side
1.50
Install the fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the LH
side
0.75
Remove the fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the RH
side
0.75
Do an Inspection of the fastener at the Holes 25, 38,
39 and 43 between STGR38 and STGR40 at FR40 on
the RH side
0.75
Do a Cold Working of the fastener Holes 25, 38, 39
and 43 between STGR38 and STGR40 at FR40 on the
RH side
1.50
Install the fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the RH
side
0.75
Tests
 0.50
Close-Up
 11.00
TOTAL MANHOURS
 29.00
ELAPSED TIME (HOURS)
 14.75
NOTE
: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-FAAAA
 given in Appendix 01 - Manpower Gantt Chart .
**CONF 002
Task 574139-831-801-001: Modification
Get Access
 10.00
On Aircraft
Remove the Fastener at the Holes 38, 39 and 43
between STGR38 and STGR40 at FR40 on the LH
side
0.50
Do an Inspection of the Fastener at the Holes 38, 39
and 43 between STGR38 and STGR40 at FR40 on the
LH side
0.50
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 8
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 15

@A340
SERVICE BULLETIN
Task 574139-831-801-001: Modification
Do a Cold Working of the fastener Holes 38, 39 and 43
between STGR38 and STGR40 at FR40 on the LH
side
1.00
Install the fastener at the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the LH side
0.50
Remove the fastener at the Holes 38, 39 and 43
between STGR38 and STGR40 at FR40 on the RH
side
0.50
Do an Inspection of the fastener at the Holes 38, 39
and 43 between STGR38 and STGR40 at FR40 on the
RH side
0.50
Do a Cold Working of the fastener Holes 38, 39 and 43
between STGR38 and STGR40 at FR40 on the RH
side
1.00
Install the fastener at the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the RH side
0.50
Tests
 0.50
Close-Up
 11.00
TOTAL MANHOURS
 26.50
ELAPSED TIME (HOURS)
 13.50
NOTE
: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-FAAAB
 given in Appendix 01 - Manpower Gantt Chart .
**CONF 003
Task 574139-831-801-001: Modification
Get Access
 10.00
On Aircraft
Remove the Fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the LH
side
0.75
Do an Inspection of the fastener at the Holes 25, 38,
39 and 43 between STGR38 and STGR40 at FR40 on
the LH side
0.75
Do a Cold Working of the fastener Holes 25, 38, 39
and 43 between STGR38 and STGR40 at FR40 on the
LH side
1.50
Install the fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the LH
side
0.75
Remove the fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the RH
side
0.75
Do an Inspection of the fastener at the Holes 25, 38,
39 and 43 between STGR38 and STGR40 at FR40 on
the RH side
0.75
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 9
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 16

@A340
SERVICE BULLETIN
Task 574139-831-801-001: Modification
Do a Cold Working of the fastener Holes 25, 38, 39
and 43 between STGR38 and STGR40 at FR40 on the
RH side
1.50
Install the fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the RH
side
0.75
Tests
 0.50
Close-Up
 11.00
TOTAL MANHOURS
 29.00
ELAPSED TIME (HOURS)
 14.75
NOTE
: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-FAAAA
 given in Appendix 01 - Manpower Gantt Chart .
**CONF 004
Task 574139-831-801-001: Modification
Get Access
 10.00
On Aircraft
Remove the Fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the LH
side
0.75
Do an Inspection of the fastener at the Holes 25, 38,
39 and 43 between STGR38 and STGR40 at FR40 on
the LH side
0.75
Do a Cold Working of the fastener Holes 25, 38, 39
and 43 between STGR38 and STGR40 at FR40 on the
LH side
1.50
Install the fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the LH
side
0.75
Remove the fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the RH
side
0.75
Do an Inspection of the fastener at the Holes 25, 38,
39 and 43 between STGR38 and STGR40 at FR40 on
the RH side
0.75
Do a Cold Working of the fastener Holes 25, 38, 39
and 43 between STGR38 and STGR40 at FR40 on the
RH side
1.50
Install the fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the RH
side
0.75
Tests
 0.50
Close-Up
 11.00
TOTAL MANHOURS
 29.00
ELAPSED TIME (HOURS)
 14.75
NOTE
: For an explanation of the manhours and elapsed time, refer to the Gantt
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 10
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 17

@A340
SERVICE BULLETIN
Chart, Fig. A-FAAAA
 given in Appendix 01 - Manpower Gantt Chart .
**CONF ALL
H. WEIGHT AND BALANCE
Not Changed
I. ELECTRICAL LOAD DATA
Not Changed
J. REFERENCES
**CONF 001
Aircraft Maintenance Manual (AMM)
 06-20-00 06-31-53 06-41-53
12-34-24 20-16-00 20-21-11
21-20-00 21-52-41 24-41-00
25-20-00 25-52-00 25-80-00
27-84-41 32-12-00 36-22-19
52-30-00 52-32-11 53-35-13
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM)
 20-55-00
In Service Information (ISI)
 51.48.00001
Non Destructive Test Manual (NTM)
 51-10-01 51-10-08
Service Bulletin (SB)
 A340-57-4125
Standards Manual (SM)
Structural Repair Manual (SRM)
 51-24-00 51-40-00 51-42-00
51-43-00 51-44-00 51-46-00
51-48-00 51-75-12 51-75-15
Tool Equipment Manual (TEM)
 52-30-00
**CONF 002
Aircraft Maintenance Manual (AMM)
 06-20-00 06-31-53 06-41-53
12-34-24 20-16-00 20-21-11
21-20-00 21-52-41 24-41-00
25-20-00 25-52-00 25-80-00
27-84-41 32-12-00 36-22-19
52-30-00 52-32-11 53-35-13
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM)
 20-55-00
In Service Information (ISI)
 51.48.00001
Non Destructive Test Manual (NTM)
 51-10-01 51-10-08
Service Bulletin (SB)
 A340-57-4125
Standards Manual (SM)
Structural Repair Manual (SRM)
 51-24-00 51-40-00 51-42-00
51-43-00 51-44-00 51-46-00
51-48-00 51-75-12 51-75-15
Tool Equipment Manual (TEM)
 52-30-00
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 11
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 18

@A340
SERVICE BULLETIN
**CONF 003
Aircraft Maintenance Manual (AMM)
 06-20-00 06-31-53 06-41-53
12-34-24 20-16-00 20-21-11
21-20-00 21-52-41 24-41-00
25-20-00 25-52-00 25-80-00
27-84-41 32-12-00 36-22-19
52-30-00 52-32-11 53-35-13
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM)
 20-55-00
In Service Information (ISI)
 51.48.00001
Non Destructive Test Manual (NTM)
 51-10-01 51-10-08
Service Bulletin (SB)
 A340-57-4125
Standards Manual (SM)
Structural Repair Manual (SRM)
 51-24-00 51-40-00 51-42-00
51-43-00 51-44-00 51-46-00
51-48-00 51-75-12 51-75-15
Tool Equipment Manual (TEM)
 52-30-00
**CONF 004
Aircraft Maintenance Manual (AMM)
 06-20-00 06-31-53 06-41-53
12-34-24 20-16-00 20-21-11
21-20-00 21-52-41 24-41-00
25-20-00 25-52-00 25-80-00
27-84-41 32-12-00 36-22-19
52-30-00 52-32-11 53-35-13
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM)
 20-55-00
In Service Information (ISI)
 51.48.00001
Non Destructive Test Manual (NTM)
 51-10-01 51-10-08
Service Bulletin (SB)
 A340-57-4125
Standards Manual (SM)
Structural Repair Manual (SRM)
 51-24-00 51-40-00 51-42-00
51-43-00 51-44-00 51-46-00
51-48-00 51-75-12 51-75-15
Tool Equipment Manual (TEM)
 52-30-00
**CONF ALL
K. PUBLICATION AFFECTED
Maintenance Planning Document (MPD)
 571134-01-2
L. INTERCHANGEABILITY/MIXABILITY
Not Applicable
M. SPARES
None
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 12
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 19

@A340
SERVICE BULLETIN
2. MATERIAL INFORMATION
**CONF ALL
A. MATERIAL - PRICE AND AVAILABILITY
(1) Procurement Addresses
Customers with aircraft shown in the effectivity of this Service Bulletin should send a
purchase order to AIRBUS. Quote the number of this Service Bulletin. The address is:
Kit 574139A01R01
Kit 574139A02R00
AIRBUS Material, Logistics and Suppliers
ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
For ordering by internet:
http://spares.airbus.com
For ordering by E-mail: airbus.kit@airbus.com
Tel ASIA: +1 310 900 1300
Fax EMEA: +49 (0) 40 822 285 31010
Fax US: +1 305 507 7191
Telephone Hotlines:
A350/A380: +49 40 743 51775
A330/340: +49 40 743 51616
A318/319/320/321: +49 40 743 51660
(2) Price and Availability
Kit 574139A01R01
Cost
 120.00 USD
Availability
 180 calendar days from receipt of order
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements
The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained through the
AirbusSpares portal or through a request for quotation to airbus.kit@airbus.com.
Kit 574139A02R00
Cost
 50.00 USD
Availability
 180 calendar days from receipt of order
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements
The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained through the
AirbusSpares portal or through a request for quotation to airbus.kit@airbus.com.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 13
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 20

@A340
SERVICE BULLETIN
B. INDUSTRY SUPPORT INFORMATION
AIRBUS will not provide industry support for accomplishment of this Service Bulletin.
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organisation of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department.
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
France
T e l:( 3 3 )56 71 90 62 2
E-mail : monitored.retrofit@airbus.com
F a x:( 3 3 )56 19 32 74 5
C. LIST OF COMPONENTS
Kit 574139A01R01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
10
 EN6115K8-22
 4
 BOLT
11
 ASNA2531-8
 6
 NUT
14
 EN6115K8-19
 2
 BOLT
NOTE
: If you find part numbers of hardware components in the related kit(s) which
you cannot identify in the LIST OF COMPONENTS of this Service Bulletin,
refer to Standards Manual (SM). The SM will give you the correct part number
to part number relationship.
Kit 574139A02R00
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
12
 EN6115K6-12
 2
 BOLT
13
 ASNA2531-6
 2
 NUT
NOTE
: If you find part numbers of hardware components in the related kit(s) which
you cannot identify in the LIST OF COMPONENTS of this Service Bulletin,
refer to Standards Manual (SM). The SM will give you the correct part number
to part number relationship.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 14
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 21

@A340
SERVICE BULLETIN
D. LIST OF MATERIALS - OPERATOR SUPPLIED
(1) Consumable Materials
Consumable CMLA01
ITEM
 DESCRIPTION
 REFERENCE TO CML
MAT. No.
QTY PER A/C
 SEE
NOTES
Coating - Flexible Structure
 04QAB2
 As required
Polysulfide Sealant-General
Purpose Interfay
06AAC1
 As required
Polysulfide Sealant-Low Density
Multi Purpose Fil
06ACB1
 As required
Polysulfide Sealant-Fuel
Contaminated Area Brusha
06ADA1
 As required
Adhesion Promoter-For Polysulfide
Sealant
06PAG1
 As required
Non Aqueous Cleaner-General
 08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
(2) Components
None
(3) Equipment
None
E. PARTS TO BE RE-IDENTIFIED BY OPERATOR
None
F. TOOLING
(1) Tooling - Price and Availability
(a) Procurement Addresses
NOTE
: Only 1 TOOL Kit is necessary to perform the Cold Working, either
TOOLA01 or TOOLA02 depending on the supplier chosen.
Operators interested in obtaining the FTI tool kit should contact:
Standard tool TOOLA01
Standard tool TOOLA02
Fatigue Technology Inc.
401 Andover Park East
SEATTLE, WA 98188-7605
USA
Internet: www.fatiguetech.com
Phone: (206) 2462010
Fax: (206) 2449886
Operators interested in obtaining the WCI tool kit should contact:
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 15
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 22

@A340
SERVICE BULLETIN
Standard tool TOOLA01
Standard tool TOOLA02
West Coast Industries Inc.
14900 Whitman Ave. N
Seattle, Washington 98133
Tel: (206) 365-7513
Fax: (206) 365-7483
Email: info@coldwork.com
Europe, Middle-East, Africa, India and
Russia: customer@capaero.com /+33 5 61
92 04 91 (France)
(b) Price and Availability
Standard tool TOOLA01
Procurement to be negotiated directly with Fatigue Technology Inc. (FTI).
Standard tool TOOLA02
Procurement to be negotiated directly with West Coast Industries Inc. (WCI).
(2) Tools
NOTE
: Only 1 TOOL Kit is necessary to perform the Cold Working, either
TOOLA01 or TOOLA02 depending on the supplier chosen.
NOTE
: To accomplish this Service Bulletin it is necessary to use the tools listed
in the subsequent re ferenced tasks:
- AMM Task 52-32-11-820-803
- NTM Task 51-10-01-250-801
- NTM Task 51-10-08
- TEM 52-30-00
Standard tool TOOLA01
ITEM
 TOOL N˚
 TOOL NAME
 QTY
 SEE
NOTES
DKA340574139-1
 Durable Tooling
 1
 (1)
EKA340574139-1
 Expandable Tooling
 1
 (2)
FTIA340574139-1
 Capital tooling
 1
 (3)
NOTE
: FTI has allocated the following tool kit numbers for cold expansion:
For the definition of capital, durable and expendable tools, refer to ISI
51.48.00001.
NOTE
 (1)
: Durable tooling: Ref. DK-A340-57-4139-1
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 16
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 23

@A340
SERVICE BULLETIN
The durable tool kit contains the minimum quantity of durable tools
necessary to accomplish the Service Bulletin on one aircraft. If the
Service Bulletin is to be accomplished on more than one aircraft, the
number of durable kits required can be established by reference to refer
to ISI 51.48.00001.
NOTE
 (2)
: Expendable tooling: Ref. EK-A340-57-4139-1
The expendable tool kit contains the quantity of expendable tools
required to accomplish the Service Bulletin on one aircraft. Order one
expendable tool kit for every aircraft on which this Service Bulletin is to
be accomplished.
NOTE
 (3)
: Capital tooling: Ref. FTI-A340-57-4139-1
The capital tools provided in this kit are not specific to this Service
Bulletin and are normally already available in operators’ stock as a long-
term investment or can be loaned from FTI.
Standard tool TOOLA02
ITEM
 TOOL N˚
 TOOL NAME
 QTY
 SEE
NOTES
DKA340574139-1
 Durable Tooling
 1
 (1)
EKA340574139-1
 Expandable Tooling
 1
 (2)
WCIA340574139-1
 Capital Tooling
 1
 (3)
NOTE
: WCI has allocated the following tool kit numbers for cold expansion:
For the definition of capital, durable and expendable tools, refer to ISI
51.48.00001.
NOTE
 (1)
: Durable tooling: Ref. DK-A340-57-4139-1
The durable tool kit contains the minimum quantity of durable tools
necessary to accomplish the Service Bulletin on one aircraft. If the
Service Bulletin is to be accomplished on more than one aircraft, the
number of durable kits required can be established by reference to refer
to ISI 51.48.00001.
NOTE
 (2)
: Expendable tooling: Ref. EK-A340-57-4139-1
The expendable tool kit contains the quantity of expendable tools
required to accomplish the Service Bulletin on one aircraft. Order one
expendable tool kit for every aircraft on which this Service Bulletin is to
be accomplished.
NOTE
 (3)
: Capital tooling: Ref. WCI-A340-57-4139-1
The capital tools provided in this kit are not specific to this Service
Bulletin and are normally already available in operators’ stock as a long-
term investment or can be loaned from WCI.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 17
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 24

@A340
SERVICE BULLETIN
(3) Special Tools
None
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 18
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 25

@A340
SERVICE BULLETIN
3. ACCOMPLISHMENT INSTRUCTIONS
Task 574139-831-801-001 - Modification
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC. AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
NOTE
: Discarded parts must be managed at the operator’s discretion.
Task Associated Data
**CONF 001
Zone
131 132
Manpower
TOTAL MANHOURS
 29.00
ELAPSED TIME (HOURS)
 14.75
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 19
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 26

@A340
SERVICE BULLETIN
**CONF 002
Zone
131 132
Manpower
TOTAL MANHOURS
 26.50
ELAPSED TIME (HOURS)
 13.50
**CONF 003
Zone
131 132
Manpower
TOTAL MANHOURS
 29.00
ELAPSED TIME (HOURS)
 14.75
**CONF 004
Zone
131 132
Manpower
TOTAL MANHOURS
 29.00
ELAPSED TIME (HOURS)
 14.75
**CONF ALL
A. GENERAL
**CONF 001
(1) Subtask 574139-910-001-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
Task 20-16-00-912-801
Task 20-21-11-911-801
Task 21-20-00-010-801
Consumable Material List (CML)
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 20
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 27

@A340
SERVICE BULLETIN
References
Structural Repair Manual (SRM)
 51-24-00
51-40-00
51-42-00
51-43-00
51-44-00
51-48-00
51-75-12
51-75-15
(a) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.
(c) For the identification of access panels, refer to AMM 06-41-53, Page Block 001.
(d) For the specification of the materials (Mat. No.) given in this Service Bulletin, refer
to the Consumable Materials List (Consumable Material List (CML)).
(e) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.
(f) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.
(g) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.
(h) Remove and install fasteners in accordance with SRM 51-42-00.
(i) Obtain fastener hole diameters and drill data in accordance with SRM 51-44-00.
(j) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-801.
(k) For the general removal of air-conditioning distribution ducts, refer to AMM Task
21-20-00-010-801.
(l) Do the cold working of the fastener holes in accordance with SRM 51-48-00.
(m) Apply sealant in accordance with SRM 51-24-00.
(n) Renew the protective finish in accordance with SRM 51-75-12.
(2) Subtask 574139-839-001-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 21
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 28

@A340
SERVICE BULLETIN
**CONF 002
(1) Subtask 574139-910-001-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
Task 20-16-00-912-801
Task 20-21-11-911-801
Task 21-20-00-010-801
Consumable Material List (CML)
Structural Repair Manual (SRM)
 51-24-00
51-40-00
51-42-00
51-43-00
51-44-00
51-48-00
51-75-12
51-75-15
(a) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.
(c) For the identification of access panels, refer to AMM 06-41-53, Page Block 001.
(d) For the specification of the materials (Mat. No.) given in this Service Bulletin, refer
to the Consumable Materials List (Consumable Material List (CML)).
(e) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.
(f) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.
(g) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.
(h) Remove and install fasteners in accordance with SRM 51-42-00.
(i) Obtain fastener hole diameters and drill data in accordance with SRM 51-44-00.
(j) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-801.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 22
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 29

@A340
SERVICE BULLETIN
(k) For the general removal of air-conditioning distribution ducts, refer to AMM Task
21-20-00-010-801.
(l) Do the cold working of the fastener holes in accordance with SRM 51-48-00.
(m) Apply sealant in accordance with SRM 51-24-00.
(n) Renew the protective finish in accordance with SRM 51-75-12.
(2) Subtask 574139-839-001-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
**CONF 003
(1) Subtask 574139-910-001-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
Task 20-16-00-912-801
Task 20-21-11-911-801
Task 21-20-00-010-801
Consumable Material List (CML)
Structural Repair Manual (SRM)
 51-24-00
51-40-00
51-42-00
51-43-00
51-44-00
51-48-00
51-75-12
51-75-15
(a) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.
(c) For the identification of access panels, refer to AMM 06-41-53, Page Block 001.
(d) For the specification of the materials (Mat. No.) given in this Service Bulletin, refer
to the Consumable Materials List (Consumable Material List (CML)).
(e) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 23
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 30

@A340
SERVICE BULLETIN
(f) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.
(g) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.
(h) Remove and install fasteners in accordance with SRM 51-42-00.
(i) Obtain fastener hole diameters and drill data in accordance with SRM 51-44-00.
(j) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-801.
(k) For the general removal of air-conditioning distribution ducts, refer to AMM Task
21-20-00-010-801.
(l) Do the cold working of the fastener holes in accordance with SRM 51-48-00.
(m) Apply sealant in accordance with SRM 51-24-00.
(n) Renew the protective finish in accordance with SRM 51-75-12.
(2) Subtask 574139-839-001-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
**CONF 004
(1) Subtask 574139-910-001-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
Task 20-16-00-912-801
Task 20-21-11-911-801
Task 21-20-00-010-801
Consumable Material List (CML)
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 24
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 31

@A340
SERVICE BULLETIN
References
Structural Repair Manual (SRM)
 51-24-00
51-40-00
51-42-00
51-43-00
51-44-00
51-48-00
51-75-12
51-75-15
(a) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.
(c) For the identification of access panels, refer to AMM 06-41-53, Page Block 001.
(d) For the specification of the materials (Mat. No.) given in this Service Bulletin, refer
to the Consumable Materials List (Consumable Material List (CML)).
(e) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.
(f) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.
(g) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.
(h) Remove and install fasteners in accordance with SRM 51-42-00.
(i) Obtain fastener hole diameters and drill data in accordance with SRM 51-44-00.
(j) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-801.
(k) For the general removal of air-conditioning distribution ducts, refer to AMM Task
21-20-00-010-801.
(l) Do the cold working of the fastener holes in accordance with SRM 51-48-00.
(m) Apply sealant in accordance with SRM 51-24-00.
(n) Renew the protective finish in accordance with SRM 51-75-12.
(2) Subtask 574139-839-001-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 25
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 32

@A340
SERVICE BULLETIN
**CONF ALL
B. PREPARATION
**CONF 001
(1) Subtask 574139-941-001-001 - Job Set-up
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 12-34-24-860-802
Task 21-20-00-010-801
Task 24-41-00-861-801
Task 25-80-00-000-801
Task 27-84-41-000-802
Task 32-12-00-010-801
52-30-00, Page Block 201
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-860-802.
(b) Put an access platform(s) in position at doors 821.
(c) Open the Main Landing Gear (MLG) doors, refer to AMM Task 32-12-00-010-801.
(d) Open the FWD cargo-compartment door 821, refer to AMM 52-30-00, Page Block
201.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 26
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 33

@A340
SERVICE BULLETIN
(e) At Frame 40, in the applicable work area, remove the insulation blankets, refer to
AMM Task 25-80-00-000-801.
(f) Remove the gearbox right angle 5011CW and 5071CW, refer to AMM Task
27-84-41-000-802.
(g) Remove the necessary air-conditioning ducts, refer to AMM Task
21-20-00-010-801.
(h) Energize the aircraft electrical circuits, refer to AMM Task AMM Task
24-41-00-861-801.
(2) Subtask 574139-941-002-001 - Safety Precautions
Manpower Resources
Skills
 NON SPECIFIC
(a) On the AIR control panel 225VU:
1
 Make sure that the APU BLEED, the ENG BLEED 1(2) and the PACK 1(2)
pushbutton switches are released.
2
 Put a WARNING NOTICE in position to tell persons not to operate these
pushbutton switches.
(b) On the HP ground connectors, put a WARNING NOTICE in position to tell persons
not to supply the ground air source.
(3) Subtask 574139-010-001-001 - Remove/Open for access in the Belly Fairing Area
LH side
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 21-52-41-000-801
Task 53-35-13-000-802
(a) Remove the Belly Fairing Access-Panels 191FB, 191KB and 192PB, refer to AMM
Task 53-35-13-000-802.
(b) Remove the Air Conditioning Pack (FIN 521HF), refer to AMM Task
21-52-41-000-801.
(4) Subtask 574139-010-002-001 - Remove/Open for Access in the Belly Fairing Areas
RH side
Manpower Resources
Skills
 NON SPECIFIC
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 27
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 34

@A340
SERVICE BULLETIN
References
Aircraft Maintenance Manual (AMM)
 Task 21-20-00-010-801
Task 21-52-41-000-801
Task 36-22-19-000-801
Task 53-35-13-000-802
Fig. A-FBCAA
Removal/Installation of the Air
Conditioning Ducts between FR39.1 and
FR40 (Belly Fairing Area)
Sheet 01
Fig. A-FBDAA
Removal/Installation of the Air
Conditioning Ducts between FR39.1 and
FR40 (Belly Fairing Area)
Sheet 01
Fig. A-FBAAA
Removal/Installation of the Heat Shield
Sheet 01
Sheet 02
WARNING
: MAKE SURE THAT AIR IS NOT SUPPLIED TO THE AIR
CONDITIONING SYSTEM FROM THE MAIN ENGINE, THE APU OR A
GROUND SOURCE.
HOT COMPRESSED AIR CAN CAUSE INJURY TO PERSONNEL.
(a) Remove the belly fairing access-panels 193DB, 192JB and 192GB, refer to AMM
Task 53-35-13-000-802.
(b) If necessary, on the Right Hand (RH) side, remove and retain the air-conditioning
pack outlet duct as follows, refer to AMM Task 21-20-00-010-801 and Fig. A-
FBCAA Sheet 01
.
1
 Remove:
1 Duct Item (5) Retain
(c) On the RH side, remove and retain the air ventilation duct as follows, refer to AMM
Task 21-20-00-010-801 and Fig. A-FBDAA Sheet 01
 .
1
 Remove:
1 Duct Item (6) Retain
(d) Remove the Air Conditioning Pack (FIN 522HF), refer to AMM Task
21-52-41-000-801.
(e) If necessary, remove the Wing Bleed-air Duct Sensing Elements (FINs 120HF,
122HF, 124HF, 131HF, 133HF and 135HF), refer to AMM Task 36-22-19-000-801.
(f) Remove the Heat Shield of the RH Conditioning Pack, refer to Fig. A-FBAAA Sheet
01
 and Fig. A-FBAAA Sheet 02
 .
1 Heat Shield Item (7) Retain
4 Screw Item (8) Retain
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 28
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 35

@A340
SERVICE BULLETIN
(5) Subtask 574139-010-003-001 - Remove/Open for Access in the FWD Cargo-
Compartment
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 21-20-00-010-801
Task 25-20-00-010-801
Task 25-52-00-000-801
Task 25-80-00-000-801
Task 52-30-00-010-801
Fig. A-FBBAA
Removal/Installation of the Air
Conditioning Ducts between FR39.1 and
FR40 (FWD Cargo- Compartment)
Sheet 01
CAUTION
: DO NOT STEP ON THE DUCTS BECAUSE THEY ARE FRAGILE.
(a) Open the 821 FWD cargo-compartment door, refer to AMM Task
52-30-00-010-801.
(b) Remove the Ceiling Panels, the Partition Panels and the Sidewall Panels in the
Forward Cargo Compartment 131CX, 131DX, 132CX and 132DX, refer to AMM
Task 25-52-00-000-801.
(c) On the LH and RH sides, remove the air conditioning ducts between Frame 39.1
and Frame 40, refer to AMM Task 21-20-00-010-801 and Fig. A-FBBAA Sheet 01
 .
1
 Remove:
2 Duct Item (1) Retain
2 Duct Item (2) Retain
2 Recirculation Filter Item (3) Retain
2 Recirculation Fan Item (4) Retain
(d) Remove the necessary insulation blankets, refer to AMM Task 25-80-00-000-801.
**CONF 002
(1) Subtask 574139-941-001-001 - Job Set-up
Manpower Resources
Skills
 NON SPECIFIC
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 29
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 36

@A340
SERVICE BULLETIN
References
Aircraft Maintenance Manual (AMM)
 Task 12-34-24-860-802
Task 21-20-00-010-801
Task 24-41-00-861-801
Task 25-80-00-000-801
Task 27-84-41-000-802
Task 32-12-00-010-801
52-30-00, Page Block 201
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-860-802.
(b) Put an access platform(s) in position at doors 821.
(c) Open the Main Landing Gear (MLG) doors, refer to AMM Task 32-12-00-010-801.
(d) Open the FWD cargo-compartment door 821, refer to AMM 52-30-00, Page Block
201.
(e) At Frame 40, in the applicable work area, remove the insulation blankets, refer to
AMM Task 25-80-00-000-801.
(f) Remove the gearbox right angle 5011CW and 5071CW, refer to AMM Task
27-84-41-000-802.
(g) Remove the necessary air-conditioning ducts, refer to AMM Task
21-20-00-010-801.
(h) Energize the aircraft electrical circuits, refer to AMM Task AMM Task
24-41-00-861-801.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 30
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 37

@A340
SERVICE BULLETIN
(2) Subtask 574139-941-002-001 - Safety Precautions
Manpower Resources
Skills
 NON SPECIFIC
(a) On the AIR control panel 225VU:
1
 Make sure that the APU BLEED, the ENG BLEED 1(2) and the PACK 1(2)
pushbutton switches are released.
2
 Put a WARNING NOTICE in position to tell persons not to operate these
pushbutton switches.
(b) On the HP ground connectors, put a WARNING NOTICE in position to tell persons
not to supply the ground air source.
(3) Subtask 574139-010-001-001 - Remove/Open for access in the Belly Fairing Area
LH side
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 21-52-41-000-801
Task 53-35-13-000-802
(a) Remove the Belly Fairing Access-Panels 191FB, 191KB and 192PB, refer to AMM
Task 53-35-13-000-802.
(b) Remove the Air Conditioning Pack (FIN 521HF), refer to AMM Task
21-52-41-000-801.
(4) Subtask 574139-010-002-001 - Remove/Open for Access in the Belly Fairing Areas
RH side
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 21-20-00-010-801
Task 21-52-41-000-801
Task 36-22-19-000-801
Task 53-35-13-000-802
Fig. A-FBCAA
Removal/Installation of the Air
Conditioning Ducts between FR39.1 and
FR40 (Belly Fairing Area)
Sheet 01
Fig. A-FBDAA
Removal/Installation of the Air
Conditioning Ducts between FR39.1 and
FR40 (Belly Fairing Area)
Sheet 01
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 31
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 38

@A340
SERVICE BULLETIN
References
Fig. A-FBAAA
Removal/Installation of the Heat Shield
Sheet 01
Sheet 02
WARNING
: MAKE SURE THAT AIR IS NOT SUPPLIED TO THE AIR
CONDITIONING SYSTEM FROM THE MAIN ENGINE, THE APU OR A
GROUND SOURCE.
HOT COMPRESSED AIR CAN CAUSE INJURY TO PERSONNEL.
(a) Remove the belly fairing access-panels 193DB, 192JB and 192GB, refer to AMM
Task 53-35-13-000-802.
(b) If necessary, on the Right Hand (RH) side, remove and retain the air-conditioning
pack outlet duct as follows, refer to AMM Task 21-20-00-010-801 and Fig. A-
FBCAA Sheet 01
.
1
 Remove:
1 Duct Item (5) Retain
(c) On the RH side, remove and retain the air ventilation duct as follows, refer to AMM
Task 21-20-00-010-801 and Fig. A-FBDAA Sheet 01
 .
1
 Remove:
1 Duct Item (6) Retain
(d) Remove the Air Conditioning Pack (FIN 522HF), refer to AMM Task
21-52-41-000-801.
(e) If necessary, remove the Wing Bleed-air Duct Sensing Elements (FINs 120HF,
122HF, 124HF, 131HF, 133HF and 135HF), refer to AMM Task 36-22-19-000-801.
(f) Remove the Heat Shield of the RH Conditioning Pack, refer to Fig. A-FBAAA Sheet
01
 and Fig. A-FBAAA Sheet 02
 .
1 Heat Shield Item (7) Retain
4 Screw Item (8) Retain
(5) Subtask 574139-010-003-001 - Remove/Open for Access in the FWD Cargo-
Compartment
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 21-20-00-010-801
Task 25-20-00-010-801
Task 25-52-00-000-801
Task 25-80-00-000-801
Task 52-30-00-010-801
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 32
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 39

@A340
SERVICE BULLETIN
References
Fig. A-FBBAA
Removal/Installation of the Air
Conditioning Ducts between FR39.1 and
FR40 (FWD Cargo- Compartment)
Sheet 01
CAUTION
: DO NOT STEP ON THE DUCTS BECAUSE THEY ARE FRAGILE.
(a) Open the 821 FWD cargo-compartment door, refer to AMM Task
52-30-00-010-801.
(b) Remove the Ceiling Panels, the Partition Panels and the Sidewall Panels in the
Forward Cargo Compartment 131CX, 131DX, 132CX and 132DX, refer to AMM
Task 25-52-00-000-801.
(c) On the LH and RH sides, remove the air conditioning ducts between Frame 39.1
and Frame 40, refer to AMM Task 21-20-00-010-801 and Fig. A-FBBAA Sheet 01
 .
1
 Remove:
2 Duct Item (1) Retain
2 Duct Item (2) Retain
2 Recirculation Filter Item (3) Retain
2 Recirculation Fan Item (4) Retain
(d) Remove the necessary insulation blankets, refer to AMM Task 25-80-00-000-801.
**CONF 003
(1) Subtask 574139-941-001-001 - Job Set-up
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 12-34-24-860-802
Task 21-20-00-010-801
Task 24-41-00-861-801
Task 25-80-00-000-801
Task 27-84-41-000-802
Task 32-12-00-010-801
52-30-00, Page Block 201
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 33
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 40

@A340
SERVICE BULLETIN
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-860-802.
(b) Put an access platform(s) in position at doors 821.
(c) Open the Main Landing Gear (MLG) doors, refer to AMM Task 32-12-00-010-801.
(d) Open the FWD cargo-compartment door 821, refer to AMM 52-30-00, Page Block
201.
(e) At Frame 40, in the applicable work area, remove the insulation blankets, refer to
AMM Task 25-80-00-000-801.
(f) Remove the gearbox right angle 5011CW and 5071CW, refer to AMM Task
27-84-41-000-802.
(g) Remove the necessary air-conditioning ducts, refer to AMM Task
21-20-00-010-801.
(h) Energize the aircraft electrical circuits, refer to AMM Task AMM Task
24-41-00-861-801.
(2) Subtask 574139-941-002-001 - Safety Precautions
Manpower Resources
Skills
 NON SPECIFIC
(a) On the AIR control panel 225VU:
1
 Make sure that the APU BLEED, the ENG BLEED 1(2) and the PACK 1(2)
pushbutton switches are released.
2
 Put a WARNING NOTICE in position to tell persons not to operate these
pushbutton switches.
(b) On the HP ground connectors, put a WARNING NOTICE in position to tell persons
not to supply the ground air source.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 34
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 41

@A340
SERVICE BULLETIN
(3) Subtask 574139-010-001-001 - Remove/Open for access in the Belly Fairing Area
LH side
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 21-52-41-000-801
Task 53-35-13-000-802
(a) Remove the Belly Fairing Access-Panels 191FB, 191KB and 192PB, refer to AMM
Task 53-35-13-000-802.
(b) Remove the Air Conditioning Pack (FIN 521HF), refer to AMM Task
21-52-41-000-801.
(4) Subtask 574139-010-002-001 - Remove/Open for Access in the Belly Fairing Areas
RH side
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 21-20-00-010-801
Task 21-52-41-000-801
Task 36-22-19-000-801
Task 53-35-13-000-802
Fig. A-FBCAA
Removal/Installation of the Air
Conditioning Ducts between FR39.1 and
FR40 (Belly Fairing Area)
Sheet 01
Fig. A-FBDAA
Removal/Installation of the Air
Conditioning Ducts between FR39.1 and
FR40 (Belly Fairing Area)
Sheet 01
Fig. A-FBAAA
Removal/Installation of the Heat Shield
Sheet 01
Sheet 02
WARNING
: MAKE SURE THAT AIR IS NOT SUPPLIED TO THE AIR
CONDITIONING SYSTEM FROM THE MAIN ENGINE, THE APU OR A
GROUND SOURCE.
HOT COMPRESSED AIR CAN CAUSE INJURY TO PERSONNEL.
(a) Remove the belly fairing access-panels 193DB, 192JB and 192GB, refer to AMM
Task 53-35-13-000-802.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 35
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 42

@A340
SERVICE BULLETIN
(b) If necessary, on the Right Hand (RH) side, remove and retain the air-conditioning
pack outlet duct as follows, refer to AMM Task 21-20-00-010-801 and Fig. A-
FBCAA Sheet 01
.
1
 Remove:
1 Duct Item (5) Retain
(c) On the RH side, remove and retain the air ventilation duct as follows, refer to AMM
Task 21-20-00-010-801 and Fig. A-FBDAA Sheet 01
 .
1
 Remove:
1 Duct Item (6) Retain
(d) Remove the Air Conditioning Pack (FIN 522HF), refer to AMM Task
21-52-41-000-801.
(e) If necessary, remove the Wing Bleed-air Duct Sensing Elements (FINs 120HF,
122HF, 124HF, 131HF, 133HF and 135HF), refer to AMM Task 36-22-19-000-801.
(f) Remove the Heat Shield of the RH Conditioning Pack, refer to Fig. A-FBAAA Sheet
01
 and Fig. A-FBAAA Sheet 02
 .
1 Heat Shield Item (7) Retain
4 Screw Item (8) Retain
(5) Subtask 574139-010-003-001 - Remove/Open for Access in the FWD Cargo-
Compartment
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 21-20-00-010-801
Task 25-20-00-010-801
Task 25-52-00-000-801
Task 25-80-00-000-801
Task 52-30-00-010-801
Fig. A-FBBAA
Removal/Installation of the Air
Conditioning Ducts between FR39.1 and
FR40 (FWD Cargo- Compartment)
Sheet 01
CAUTION
: DO NOT STEP ON THE DUCTS BECAUSE THEY ARE FRAGILE.
(a) Open the 821 FWD cargo-compartment door, refer to AMM Task
52-30-00-010-801.
(b) Remove the Ceiling Panels, the Partition Panels and the Sidewall Panels in the
Forward Cargo Compartment 131CX, 131DX, 132CX and 132DX, refer to AMM
Task 25-52-00-000-801.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 36
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 43

@A340
SERVICE BULLETIN
(c) On the LH and RH sides, remove the air conditioning ducts between Frame 39.1
and Frame 40, refer to AMM Task 21-20-00-010-801 and Fig. A-FBBAA Sheet 01
 .
1
 Remove:
2 Duct Item (1) Retain
2 Duct Item (2) Retain
2 Recirculation Filter Item (3) Retain
2 Recirculation Fan Item (4) Retain
(d) Remove the necessary insulation blankets, refer to AMM Task 25-80-00-000-801.
**CONF 004
(1) Subtask 574139-941-001-001 - Job Set-up
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 12-34-24-860-802
Task 21-20-00-010-801
Task 24-41-00-861-801
Task 25-80-00-000-801
Task 27-84-41-000-802
Task 32-12-00-010-801
52-30-00, Page Block 201
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 37
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 44

@A340
SERVICE BULLETIN
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-860-802.
(b) Put an access platform(s) in position at doors 821.
(c) Open the Main Landing Gear (MLG) doors, refer to AMM Task 32-12-00-010-801.
(d) Open the FWD cargo-compartment door 821, refer to AMM 52-30-00, Page Block
201.
(e) At Frame 40, in the applicable work area, remove the insulation blankets, refer to
AMM Task 25-80-00-000-801.
(f) Remove the gearbox right angle 5011CW and 5071CW, refer to AMM Task
27-84-41-000-802.
(g) Remove the necessary air-conditioning ducts, refer to AMM Task
21-20-00-010-801.
(h) Energize the aircraft electrical circuits, refer to AMM Task AMM Task
24-41-00-861-801.
(2) Subtask 574139-941-002-001 - Safety Precautions
Manpower Resources
Skills
 NON SPECIFIC
(a) On the AIR control panel 225VU:
1
 Make sure that the APU BLEED, the ENG BLEED 1(2) and the PACK 1(2)
pushbutton switches are released.
2
 Put a WARNING NOTICE in position to tell persons not to operate these
pushbutton switches.
(b) On the HP ground connectors, put a WARNING NOTICE in position to tell persons
not to supply the ground air source.
(3) Subtask 574139-010-001-001 - Remove/Open for access in the Belly Fairing Area
LH side
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 21-52-41-000-801
Task 53-35-13-000-802
(a) Remove the Belly Fairing Access-Panels 191FB, 191KB and 192PB, refer to AMM
Task 53-35-13-000-802.
(b) Remove the Air Conditioning Pack (FIN 521HF), refer to AMM Task
21-52-41-000-801.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 38
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 45

@A340
SERVICE BULLETIN
(4) Subtask 574139-010-002-001 - Remove/Open for Access in the Belly Fairing Areas
RH side
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 21-20-00-010-801
Task 21-52-41-000-801
Task 36-22-19-000-801
Task 53-35-13-000-802
Fig. A-FBCAA
Removal/Installation of the Air
Conditioning Ducts between FR39.1 and
FR40 (Belly Fairing Area)
Sheet 01
Fig. A-FBDAA
Removal/Installation of the Air
Conditioning Ducts between FR39.1 and
FR40 (Belly Fairing Area)
Sheet 01
Fig. A-FBAAA
Removal/Installation of the Heat Shield
Sheet 01
Sheet 02
WARNING
: MAKE SURE THAT AIR IS NOT SUPPLIED TO THE AIR
CONDITIONING SYSTEM FROM THE MAIN ENGINE, THE APU OR A
GROUND SOURCE.
HOT COMPRESSED AIR CAN CAUSE INJURY TO PERSONNEL.
(a) Remove the belly fairing access-panels 193DB, 192JB and 192GB, refer to AMM
Task 53-35-13-000-802.
(b) If necessary, on the Right Hand (RH) side, remove and retain the air-conditioning
pack outlet duct as follows, refer to AMM Task 21-20-00-010-801 and Fig. A-
FBCAA Sheet 01
.
1
 Remove:
1 Duct Item (5) Retain
(c) On the RH side, remove and retain the air ventilation duct as follows, refer to AMM
Task 21-20-00-010-801 and Fig. A-FBDAA Sheet 01
 .
1
 Remove:
1 Duct Item (6) Retain
(d) Remove the Air Conditioning Pack (FIN 522HF), refer to AMM Task
21-52-41-000-801.
(e) If necessary, remove the Wing Bleed-air Duct Sensing Elements (FINs 120HF,
122HF, 124HF, 131HF, 133HF and 135HF), refer to AMM Task 36-22-19-000-801.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 39
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 46

@A340
SERVICE BULLETIN
(f) Remove the Heat Shield of the RH Conditioning Pack, refer to Fig. A-FBAAA Sheet
01
 and Fig. A-FBAAA Sheet 02
 .
1 Heat Shield Item (7) Retain
4 Screw Item (8) Retain
(5) Subtask 574139-010-003-001 - Remove/Open for Access in the FWD Cargo-
Compartment
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 21-20-00-010-801
Task 25-20-00-010-801
Task 25-52-00-000-801
Task 25-80-00-000-801
Task 52-30-00-010-801
Fig. A-FBBAA
Removal/Installation of the Air
Conditioning Ducts between FR39.1 and
FR40 (FWD Cargo- Compartment)
Sheet 01
CAUTION
: DO NOT STEP ON THE DUCTS BECAUSE THEY ARE FRAGILE.
(a) Open the 821 FWD cargo-compartment door, refer to AMM Task
52-30-00-010-801.
(b) Remove the Ceiling Panels, the Partition Panels and the Sidewall Panels in the
Forward Cargo Compartment 131CX, 131DX, 132CX and 132DX, refer to AMM
Task 25-52-00-000-801.
(c) On the LH and RH sides, remove the air conditioning ducts between Frame 39.1
and Frame 40, refer to AMM Task 21-20-00-010-801 and Fig. A-FBBAA Sheet 01
 .
1
 Remove:
2 Duct Item (1) Retain
2 Duct Item (2) Retain
2 Recirculation Filter Item (3) Retain
2 Recirculation Fan Item (4) Retain
(d) Remove the necessary insulation blankets, refer to AMM Task 25-80-00-000-801.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 40
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 47

@A340
SERVICE BULLETIN
**CONF ALL
C. PROCEDURE
**CONF 001
(1) Subtask 574139-000-001-002 - Remove the Fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the LH side
Work Zones and Access Panels
Zone
 Access/Work location
131
 Work location
 Frame 40
from Stringer 38 to Stringer 40
Manpower Resources
Manhours
 0.75
Minimum number of person
 1
Subtask elapsed time
 0.75
Skills
 AIRFRAME
Material necessary to do the job
Consumable CMLA01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Non Aqueous Cleaner-
General
08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
References
Structural Repair Manual (SRM)
 51-42-00
Fig. A-FBEAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
Fig. A-FBFAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
(a) Remove as shown on Fig. A-FBEAA Sheet 01
 , Fig. A-FBFAA Sheet 01
 and in
accordance with SRM 51-42-00:
3 Bolt Item (10) Discard
3 Nut Item (11) Discard
1 Bolt Item (12) Discard
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 41
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 48

@A340
SERVICE BULLETIN
1 Nut Item (13) Discard
(b) Remove the old sealant with a non metallic spatula.
(c) Clean the structure area with:
Non Aqueous
Cleaner-General
08BAA9 As required
and
Textile-Lint Free
Cotton
14SBA1 As required
(2) Subtask 574139-250-001-002 - Do an Inspection of the fastener at the Holes 25, 38,
39 and 43 between STGR38 and STGR40 at FR40 on the LH side
Work Zones and Access Panels
Zone
 Access/Work location
131
 Work location
 Frame 40
from Stringer 38 to Stringer 40
Manpower Resources
Manhours
 0.75
Minimum number of person
 1
Subtask elapsed time
 0.75
Skills
 NON DESTRUCTIVE
TESTING
References
Non Destructive Test Manual (NTM)
 51-10-01
Fig. A-FBEAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
Fig. A-FBFAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
(a) Do a rotating probe test of the fastener holes as shown in Fig. A-FBEAA Sheet 01
and Fig. A-FBFAA Sheet 01
 in accordance with NTM 51-10-01.
1
 In case of crack findings in the fastener holes, contact AIRBUS before next
flight and follow their instructions.
2
 In case of no crack findings, in accordance with SUBTASK 574139-831-001
002 Do a Cold Working of the fastener Holes 25, 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the LH side .
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 42
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 49

@A340
SERVICE BULLETIN
(3) Subtask 574139-831-001-002 - Do a Cold Working of the fastener Holes 25, 38, 39
and 43 between STGR38 and STGR40 at FR40 on the LH side
Work Zones and Access Panels
Zone
 Access/Work location
131
 Work location
 Frame 40
from Stringer 38 to Stringer 40
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
Material necessary to do the job
Standard tool TOOLA01
ITEM
 TOOL N˚
 TOOL NAME
 QTY
 SEE
NOTES
DKA340574139-1
 Durable Tooling
 1
 (1)
EKA340574139-1
 Expandable Tooling
 1
 (2)
FTIA340574139-1
 Capital tooling
 1
 (3)
NOTE
: FTI has allocated the following tool kit numbers for cold expansion:
For the definition of capital, durable and expendable tools, refer to ISI
51.48.00001.
NOTE
 (1)
: Durable tooling: Ref. DK-A340-57-4139-1
The durable tool kit contains the minimum quantity of durable tools
necessary to accomplish the Service Bulletin on one aircraft. If the
Service Bulletin is to be accomplished on more than one aircraft, the
number of durable kits required can be established by reference to refer
to ISI 51.48.00001.
NOTE
 (2)
: Expendable tooling: Ref. EK-A340-57-4139-1
The expendable tool kit contains the quantity of expendable tools
required to accomplish the Service Bulletin on one aircraft. Order one
expendable tool kit for every aircraft on which this Service Bulletin is to
be accomplished.
NOTE
 (3)
: Capital tooling: Ref. FTI-A340-57-4139-1
The capital tools provided in this kit are not specific to this Service
Bulletin and are normally already available in operators’ stock as a long-
term investment or can be loaned from FTI.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 43
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 50

@A340
SERVICE BULLETIN
Standard tool TOOLA02
ITEM
 TOOL N˚
 TOOL NAME
 QTY
 SEE
NOTES
DKA340574139-1
 Durable Tooling
 1
 (1)
EKA340574139-1
 Expandable Tooling
 1
 (2)
WCIA340574139-1
 Capital Tooling
 1
 (3)
NOTE
: WCI has allocated the following tool kit numbers for cold expansion:
For the definition of capital, durable and expendable tools, refer to ISI
51.48.00001.
NOTE
 (1)
: Durable tooling: Ref. DK-A340-57-4139-1
The durable tool kit contains the minimum quantity of durable tools
necessary to accomplish the Service Bulletin on one aircraft. If the
Service Bulletin is to be accomplished on more than one aircraft, the
number of durable kits required can be established by reference to refer
to ISI 51.48.00001.
NOTE
 (2)
: Expendable tooling: Ref. EK-A340-57-4139-1
The expendable tool kit contains the quantity of expendable tools
required to accomplish the Service Bulletin on one aircraft. Order one
expendable tool kit for every aircraft on which this Service Bulletin is to
be accomplished.
NOTE
 (3)
: Capital tooling: Ref. WCI-A340-57-4139-1
The capital tools provided in this kit are not specific to this Service
Bulletin and are normally already available in operators’ stock as a long-
term investment or can be loaned from WCI.
References
Structural Repair Manual (SRM)
 51-44-00
51-46-00
51-48-00
Fig. A-FBEAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
Fig. A-FBFAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 44
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 51

@A340
SERVICE BULLETIN
(a) Do a check of the existing hole diameters and compare with the values as shown
on Fig. A-FBEAA Sheet 01
 and Fig. A-FBFAA Sheet 01
 .
1
 In case the existing hole diameter is more than or equal to the minimum
starting hole diameter, please contact AIRBUS for further instructions before
next flight.
2
 In case the hole diameter is less than the minimum starting hole diameter, do
the next step.
(b) Drill and ream the fastener holes to the correct starting hole diameter as shown on
Fig. A-FBEAA Sheet 01
 and in accordance with SRM 51-44-00 and SRM 51-48-00.
Refer to FTI Tool list No.:
DKA340574139-1 Durable Tooling 1
or
Refer to WCI Tool list No.:
DKA340574139-1 Durable Tooling 1
(c) Clean the drilled areas.
(d) Do a cold working of the fastener holes.
1
 Install split sleeves as shown on Fig. A-FBEAA Sheet 01
 .
Refer to FTI Tool list No.:
EKA340574139-1 Expandable Tooling 1
or
Refer to WCI Tool list No.:
EKA340574139-1 Expandable Tooling 1
2
 Do a cold working of the fastener holes in accordance with SRM 51-48-00.
Refer to FTI Tool list No.:
FTIA340574139-1 Capital tooling 1
or
Refer to WCI Tool list No.:
WCIA340574139-1 Capital Tooling 1
3
 Remove the split sleeves.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 45
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 52

@A340
SERVICE BULLETIN
(e) Ream the fastener holes to the final hole diameter, as shown on Fig. A-FBEAA
Sheet 01
 and in accordance with SRM 51-44-00 and SRM 51-48-00.
Refer to FTI Tool list No.:
DKA340574139-1 Durable Tooling 1
or
Refer to WCI Tool list No.:
DKA340574139-1 Durable Tooling 1
(f) Clean the drilled areas.
(g) If necessary, perform a countersink to the related fastener head depth, refer to
SRM 51-46-00.
(4) Subtask 574139-400-001-002 - Install the fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the LH side
Work Zones and Access Panels
Zone
 Access/Work location
131
 Work location
 Frame 40
from Stringer 38 to Stringer 40
Manpower Resources
Manhours
 0.75
Minimum number of person
 1
Subtask elapsed time
 0.75
Skills
 AIRFRAME
Material necessary to do the job
Kit 574139A01R01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
10
 EN6115K8-22
 2
 BOLT
11
 ASNA2531-8
 3
 NUT
14
 EN6115K8-19
 1
 BOLT
Kit 574139A02R00
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
12
 EN6115K6-12
 1
 BOLT
13
 ASNA2531-6
 1
 NUT
Consumable CMLA01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Coating - Flexible Structure
 04QAB2
 As required
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 46
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 53

@A340
SERVICE BULLETIN
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Polysulfide Sealant-General
Purpose Interfay
06AAC1
 As required
Polysulfide Sealant-Low
Density Multi Purpose Fil
06ACB1
 As required
Adhesion Promoter-For
Polysulfide Sealant
06PAG1
 As required
References
Aircraft Maintenance Manual (AMM)
 Task 20-21-11-911-801
Structural Repair Manual (SRM)
 51-42-00
51-75-12
Fig. A-FBEAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
Fig. A-FBFAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
(a) Install the fasteners to the aircraft structure.
1
 Wet install in accordance with SRM 51-42-00, refer to Fig. A-FBEAA Sheet 01
and Fig. A-FBFAA Sheet 01
 and AMM Task 20-21-11-911-801.
2 Bolt EN6115K8-22 Item 10
1 Bolt EN6115K8-19 Item 14
3 Nut ASNA2531-8 Item 11
1 Bolt EN6115K6-12 Item 12
1 Nut ASNA2531-6 Item 13
with
Polysulfide Sealant-
General Purpose
Interfay
06AAC1 As required
2
 Clean the work area.
(b) Apply protective finish on the fasteners.
Refer to Fig. A-FBEAA Sheet 01
 and Fig. A-FBFAA Sheet 01
In accordance with SRM 51-75-12
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 47
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 54

@A340
SERVICE BULLETIN
1
 Apply to the bolts head:
Adhesion Promoter-
For Polysulfide
Sealant
06PAG1 As required
Polysulfide Sealant-
Low Density Multi
Purpose Fil
06ACB1 As required
Coating - Flexible
Structure
04QAB2 As required
2
 Apply to the nuts:
Adhesion Promoter-
For Polysulfide
Sealant
06PAG1 As required
Polysulfide Sealant-
Low Density Multi
Purpose Fil
06ACB1 As required
Coating - Flexible
Structure
04QAB2 As required
(5) Subtask 574139-000-002-002 - Remove the fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the RH side
Work Zones and Access Panels
Zone
 Access/Work location
132
 Work location
 Frame 40
from Stringer 38 to Stringer 40
Manpower Resources
Manhours
 0.75
Minimum number of person
 1
Subtask elapsed time
 0.75
Skills
 AIRFRAME
Material necessary to do the job
Consumable CMLA01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Non Aqueous Cleaner-
General
08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 48
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 55

@A340
SERVICE BULLETIN
References
Structural Repair Manual (SRM)
 51-42-00
Fig. A-FBEAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
Fig. A-FBFAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
(a) Remove as shown on Fig. A-FBEAA Sheet 01
 , Fig. A-FBFAA Sheet 01
 and in
accordance with SRM 51-42-00:
3 Bolt Item (10) Discard
3 Nut Item (11) Discard
1 Bolt Item (12) Discard
1 Nut Item (13) Discard
(b) Remove the old sealant with a non metallic spatula.
(c) Clean the structure area with:
Non Aqueous
Cleaner-General
08BAA9 As required
and
Textile-Lint Free
Cotton
14SBA1 As required
NOTE
: Do a check of the actual diameter and compare with the dimension
given in Fig. A-FBEAA Sheet 01
 and Fig. A-FBFAA Sheet 01
 .
If the values are not correct, contact AIRBUS.
(6) Subtask 574139-250-002-002 - Do an Inspection of the fastener at the Holes 25, 38,
39 and 43 between STGR38 and STGR40 at FR40 on the RH side
Work Zones and Access Panels
Zone
 Access/Work location
132
 Work location
 Frame 40
from Stringer 38 to Stringer 39
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 49
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 56

@A340
SERVICE BULLETIN
Manpower Resources
Manhours
 0.75
Minimum number of person
 1
Subtask elapsed time
 0.75
Skills
 NON DESTRUCTIVE
TESTING
References
Non Destructive Test Manual (NTM)
 51-10-01
Fig. A-FBEAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
Fig. A-FBFAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
(a) Do a rotating probe test of the fastener holes as shown in Fig. A-FBEAA Sheet 01
and Fig. A-FBFAA Sheet 01
 in accordance with NTM 51-10-01.
1
 In case of crack findings in the fastener holes, contact AIRBUS before next
flight and follow their instructions.
2
 In case of no crack findings, in accordance with SUBTASK 574139-831-002
002 Do a Cold Working of the fastener Holes 25, 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the RH side .
(7) Subtask 574139-831-002-002 - Do a Cold Working of the fastener Holes 25, 38, 39
and 43 between STGR38 and STGR40 at FR40 on the RH side
Work Zones and Access Panels
Zone
 Access/Work location
132
 Work location
 Frame 40
from Stringer 38 to Stringer 40
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 50
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 57

@A340
SERVICE BULLETIN
Material necessary to do the job
Standard tool TOOLA01
ITEM
 TOOL N˚
 TOOL NAME
 QTY
 SEE
NOTES
DKA340574139-1
 Durable Tooling
 1
 (1)
EKA340574139-1
 Expandable Tooling
 1
 (2)
FTIA340574139-1
 Capital tooling
 1
 (3)
NOTE
: FTI has allocated the following tool kit numbers for cold expansion:
For the definition of capital, durable and expendable tools, refer to ISI
51.48.00001.
NOTE
 (1)
: Durable tooling: Ref. DK-A340-57-4139-1
The durable tool kit contains the minimum quantity of durable tools
necessary to accomplish the Service Bulletin on one aircraft. If the
Service Bulletin is to be accomplished on more than one aircraft, the
number of durable kits required can be established by reference to refer
to ISI 51.48.00001.
NOTE
 (2)
: Expendable tooling: Ref. EK-A340-57-4139-1
The expendable tool kit contains the quantity of expendable tools
required to accomplish the Service Bulletin on one aircraft. Order one
expendable tool kit for every aircraft on which this Service Bulletin is to
be accomplished.
NOTE
 (3)
: Capital tooling: Ref. FTI-A340-57-4139-1
The capital tools provided in this kit are not specific to this Service
Bulletin and are normally already available in operators’ stock as a long-
term investment or can be loaned from FTI.
Standard tool TOOLA02
ITEM
 TOOL N˚
 TOOL NAME
 QTY
 SEE
NOTES
DKA340574139-1
 Durable Tooling
 1
 (1)
EKA340574139-1
 Expandable Tooling
 1
 (2)
WCIA340574139-1
 Capital Tooling
 1
 (3)
NOTE
: WCI has allocated the following tool kit numbers for cold expansion:
For the definition of capital, durable and expendable tools, refer to ISI
51.48.00001.
NOTE
 (1)
: Durable tooling: Ref. DK-A340-57-4139-1
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 51
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 58

@A340
SERVICE BULLETIN
The durable tool kit contains the minimum quantity of durable tools
necessary to accomplish the Service Bulletin on one aircraft. If the
Service Bulletin is to be accomplished on more than one aircraft, the
number of durable kits required can be established by reference to refer
to ISI 51.48.00001.
NOTE
 (2)
: Expendable tooling: Ref. EK-A340-57-4139-1
The expendable tool kit contains the quantity of expendable tools
required to accomplish the Service Bulletin on one aircraft. Order one
expendable tool kit for every aircraft on which this Service Bulletin is to
be accomplished.
NOTE
 (3)
: Capital tooling: Ref. WCI-A340-57-4139-1
The capital tools provided in this kit are not specific to this Service
Bulletin and are normally already available in operators’ stock as a long-
term investment or can be loaned from WCI.
References
Structural Repair Manual (SRM)
 51-44-00
51-46-00
51-48-00
Fig. A-FBEAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
Fig. A-FBFAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
(a) Do a check of the existing hole diameters and compare with the values as shown
on Fig. A-FBEAA Sheet 01
 and Fig. A-FBFAA Sheet 01
 .
1
 In case the existing hole diameter is more than or equal to the minimum
starting hole diameter, please contact AIRBUS for further instructions before
next flight.
2
 In case the hole diameter is less than the minimum starting hole diameter, do
the next step.
(b) Drill and ream the fastener holes to the correct starting hole diameter as shown on
Fig. A-FBEAA Sheet 01
 and in accordance with SRM 51-44-00 and SRM 51-48-00.
Refer to FTI Tool list No.:
DKA340574139-1 Durable Tooling 1
or
Refer to WCI Tool list No.:
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 52
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 59

@A340
SERVICE BULLETIN
DKA340574139-1 Durable Tooling 1
(c) Clean the drilled areas.
(d) Do a cold working of the fastener holes.
1
 Install split sleeves as shown on Fig. A-FBEAA Sheet 01
 .
Refer to FTI Tool list No.:
EKA340574139-1 Expandable Tooling 1
or
Refer to WCI Tool list No.:
EKA340574139-1 Expandable Tooling 1
2
 Do a cold working of the fastener holes in accordance with SRM 51-48-00.
Refer to FTI Tool list No.:
FTIA340574139-1 Capital tooling 1
or
Refer to WCI Tool list No.:
WCIA340574139-1 Capital Tooling 1
3
 Remove the split sleeves.
(e) Ream the fastener holes to the final hole diameter, as shown on Fig. A-FBEAA
Sheet 01
 and in accordance with SRM 51-44-00 and SRM 51-48-00.
Refer to FTI Tool list No.:
DKA340574139-1 Durable Tooling 1
or
Refer to WCI Tool list No.:
DKA340574139-1 Durable Tooling 1
(f) Clean the drilled areas.
(g) If necessary, perform a countersink to the related fastener head depth, refer to
SRM 51-46-00.
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 53
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 60

@A340
SERVICE BULLETIN
(8) Subtask 574139-400-002-002 - Install the fastener at the Holes 25, 38, 39 and 43
between STGR38 and STGR40 at FR40 on the RH side
Work Zones and Access Panels
Zone
 Access/Work location
132
 Work location
 Frame 40
from Stringer 38 to Stringer 40
Manpower Resources
Manhours
 0.75
Minimum number of person
 1
Subtask elapsed time
 0.75
Skills
 AIRFRAME
Material necessary to do the job
Kit 574139A01R01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
10
 EN6115K8-22
 2
 BOLT
11
 ASNA2531-8
 3
 NUT
14
 EN6115K8-19
 1
 BOLT
Kit 574139A02R00
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
12
 EN6115K6-12
 1
 BOLT
13
 ASNA2531-6
 1
 NUT
Consumable CMLA01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Coating - Flexible Structure
 04QAB2
 As required
Polysulfide Sealant-General
Purpose Interfay
06AAC1
 As required
Polysulfide Sealant-Low
Density Multi Purpose Fil
06ACB1
 As required
Adhesion Promoter-For
Polysulfide Sealant
06PAG1
 As required
References
Aircraft Maintenance Manual (AMM)
 Task 20-21-11-911-801
Structural Repair Manual (SRM)
 51-42-00
51-75-12
Fig. A-FBEAA
Removal/Installation of the fastener of
the Holes 38, 39 and 43 between
STGR38 and STGR40 at FR40 on the
LH and the RH side
Sheet 01
DATE: Nov 23/16 SERVICE BULLETIN No.: A340-57-4139
REVISION No.: 00 - Nov 23/16 Page: 54
5
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

The text continues at https://openairdocs.org/service-documents/airbus/a340-57-4139/file/b5098249aff1.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
