# Airbus Service Bulletin A350-25-P122

Copy: No revision named ("SB_25-P122_R02"), 45 pages: PDF https://openairdocs.org/files/sha256/3a/15/3a15a45810343c2966cdb58484c0abca13c9d71e5f98244e2a2a6b4880ddaf3a; text https://openairdocs.org/service-documents/airbus/a350-25-p122/file/3a15a4581034.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2022-0801, the docket of AD 2022-18-08. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A350-25-P122
- Page: https://openairdocs.org/service-documents/airbus/a350-25-p122

## Text (45 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2022-0801, the docket of AD 2022-18-08. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 1
CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
 
The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.
MANDATORY MANDATORY MANDATORY
ATA SYSTEM: 25
TITLE: EQUIPMENT/FURNISHINGS - COCKPIT SEATS - INSPECTION OF
COCKPIT SEATS STOP SUPPORT FITTING
MODIFICATION No.:
None

### Page 2

A350
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 2
ATA SYSTEM: 25
TITLE: EQUIPMENT/FURNISHINGS - COCKPIT SEATS - INSPECTION OF
COCKPIT SEATS STOP SUPPORT FITTING
REVISION TRANSMITTAL SHEET
This page transmits Revision No. 02 of Service Bulletin No. A350-25-P122.
A. ADDITIONAL WORK
No additional work is required by this revision.
B. REASON
Revision No. 02 issued to:
- Update the compliance to MANDATORY
- Extend the applicability of this Service Bulletin
- Delete the configurations 001 and 003.
C. CHANGES
SUMMARY
GENERAL EVALUATION Compliance becomes MANDATORY . Vendor SB
becomes YES
APPLICABILITY Operators updated.
PLANNING INFORMATION
APPLICABILITY Applicability extended.
Configuration definition Configurations 001 and 003 deleted.
COMPLIANCE
Classification Compliance becomes MANDATORY .
Accomplishment Timescale Sentence updated and sentence added.
APPROVAL Sentence updated.
MATERIAL INFORMATION
TOOLING
Referenced tools for task set
A350-A-25-XX-P122-01000-
93AA-A Do the Repair of
the Affected Cockpit Seat(s)
in accordance with VSB
(Depending on the Inspection
Result)
Sentence updated.
LIST OF NEW PARTS
Referenced parts for task set
A350-A-25-XX-P122-01000-
93AA-A Do the Repair of
the Affected Cockpit Seat(s)
in accordance with VSB
(Depending on the Inspection
Result)
Sentence updated.
ACCOMPLISHMENT INSTRUCTIONS
T ask set A350-A-25-XX-P122-01000-93BA-A Do the Inspection of the Cockpit Seat(s)

### Page 3

A350
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 3
TASK SET ASSOCIATED
INFORMATION
Sentence updated.
T ask set A350-A-25-XX-P122-01000-93AA-A Do the Repair of the Affected Cockpit Seat(s) in
accordance with VSB (Depending on the Inspection Result)
TASK SET ASSOCIATED
INFORMATION
NOTE added.
D. FILING INSTRUCTIONS
This Service Bulletin has been generated electronically and is reissued as a complete
document. Replace the complete document.
Put this Revision Transmittal Sheet in front of the Service Bulletin.
E. HISTORY OF PREVIOUS REVISIONS
Revision No. 01 issued to update:
- the reason paragraph of this Service Bulletin.
- the general evaluation table of this Service Bulletin.
- the configuration definition of this Service Bulletin.
- the accomplishment timescale paragraph.
NOTE: Revision No. 01 issued to incorporate changes found necessary and carried out
during the accomplishment of this Service Bulletin on aircraft with Manufacturer
Serial Number (MSN) 00149.
F. REVISION SEQUENCE
ORIGINAL: Oct 18/18
REVISION No. : 01 - Jul 12/19
REVISION No. : 02 - Oct 01/21

### Page 4

A350
SERVICE BULLETIN
SUMMARY
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 4
ATA SYSTEM: 25
TITLE: EQUIPMENT/FURNISHINGS - COCKPIT SEATS - INSPECTION OF
COCKPIT SEATS STOP SUPPORT FITTING
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR None
MINOR None
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
B. REASON
(1) History
STELIA reported to Airbus that A350 Captain (CAPT), First Officer (F/O) and 3rd
Occupant TAAI8 Series seats may be subject to a potential failure of the Vertical Stop
Support Fitting (VSSF). Without the Stop Block, the seat might disconnect from the
seat low column.
(2) Objective/Action
This Service Bulletin is published to advise the operators of the affected Manufacturer
Serial Numbers (MSNs) to inspect the VSSF .
(3) Advantages
The accomplishment of this Service Bulletin ensures the dispatch reliability of the
A350 aircraft.
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE MANDATORY COST SAVING NO
A/C OPERATION
AFFECTED
NO VENDOR SB YES
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD YES
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO
NOTE: Service Bulletin must be accomplished.
D. MAINTENANCE CONFIGURATION
No specific aircraft maintenance configuration required.

### Page 5

A350
SERVICE BULLETIN
SUMMARY
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 5
E. MATERIAL PRICE INFORMATION
(1) Do the Inspection of the Cockpit Seat(s)
(a) T ask set A350-A-25-XX-P122-01000-93BA-A Do the Inspection of the Cockpit
Seat(s)
No material
(2) Do the Repair of the Affected Cockpit Seat(s) in accordance with VSB
(Depending on the Inspection Result)
(a) T ask set A350-A-25-XX-P122-01000-93AA-A Do the Repair of the Affected Cockpit
Seat(s) in accordance with VSB (Depending on the Inspection Result)
No material
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
36V 67J 82W 96U A1L AAR AFL AFR AZU BAW CAL CCA CES CHH CPA CRK CSC CSN DAL DLH
ETD ETH EVE F2I FBU FIN FJI FWI GAF HVN IBE JAL KAY LHT MAS MAU PAL QTR SAS SIA TAM
THA THY VIR WFL
G. CONCURRENT REQUIREMENTS
None
H. NATURE OF THE WORK
(1) Do the Inspection of the Cockpit Seat(s)
(a) T ask set A350-A-25-XX-P122-01000-93BA-A Do the Inspection of the Cockpit
Seat(s)
AIRCRAFT NO
EQUIPMENT YES
(2) Do the Repair of the Affected Cockpit Seat(s) in accordance with VSB
(Depending on the Inspection Result)
(a) T ask set A350-A-25-XX-P122-01000-93AA-A Do the Repair of the Affected Cockpit
Seat(s) in accordance with VSB (Depending on the Inspection Result)
AIRCRAFT NO
EQUIPMENT YES
I. MANPOWER
(1) Do the Inspection of the Cockpit Seat(s)
(a) T ask set A350-A-25-XX-P122-01000-93BA-A Do the Inspection of the Cockpit
Seat(s)
MANPOWER
TOTAL MAN-HOURS 1.40 h
ELAPSED TIME (HOURS) 1.40 h
(2) Do the Repair of the Affected Cockpit Seat(s) in accordance with VSB
(Depending on the Inspection Result)

### Page 6

A350
SERVICE BULLETIN
SUMMARY
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 6
(a) T ask set A350-A-25-XX-P122-01000-93AA-A Do the Repair of the Affected Cockpit
Seat(s) in accordance with VSB (Depending on the Inspection Result)
MANPOWER
TOTAL MAN-HOURS 14.05 h
ELAPSED TIME (HOURS) 7.45 h
Additional man-hours related to Vendor SB; refer to:
Do the Repair of the CAPT Seat on Bench
(Depending on the Inspection Result)
Ref. STELIA AEROSPACE (F4643)
VSB TAAI8-25-1197
BENCH
Do the Repair of the F/O Seat
(Depending on the Inspection Result)
Ref. STELIA AEROSPACE (F4643)
VSB TAAI8-25-1197
BENCH
Do the Repair of the 3rd Occupant
(Depending on the Inspection Result)
Ref. STELIA AEROSPACE (F4643)
VSB TAAI8-25-1199
BENCH

### Page 7

A350
SERVICE BULLETIN
SUMMARY
Figure ICN-A350-A-25XXP122-A-FAPE3-047BS-A-001-01 Fig.SA Sol.AB SHEET 1/2
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21
General overview
Page 7
J. GENERAL OVERVIEW
CONF ALL
FR1
FR12
Z210
C
B A
A
B
4MS
3MS
INSPECTION
OF THE SEAT
INSPECTION
OF THE SEAT
ICN-A350-A-25XXP122-A-FAPE3-047BS-A-001-01

### Page 8

A350
SERVICE BULLETIN
SUMMARY
Figure ICN-A350-A-25XXP122-A-FAPE3-047BT-A-001-01 Fig.SA Sol.AB SHEET 2/2
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21
General overview
Page 8
CONF ALL
C
5000MS
INSPECTION
OF THE SEAT
ICN-A350-A-25XXP122-A-FAPE3-047BT-A-001-01

### Page 9

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 9
ATA SYSTEM: 25
TITLE: EQUIPMENT/FURNISHINGS - COCKPIT SEATS - INSPECTION OF
COCKPIT SEATS STOP SUPPORT FITTING
1. PLANNING INFORMATION
A. APPLICABILITY
(1) Models
ON A/C 0065, 0071, 0088, 0102, 0110, 0118, 0125, 0141, 0161, 0169, 0188, 0206, 0215,
0225, 0229, 0233, 0241, 0252, 0258, 0262, 0266, 0274, 0286, 0290, 0296, 0298, 0306,
0315, 0319, 0326, 0330, 0332, 0336, 0340, 0342, 0346, 0350, 0356, 0362, 0368, 0372,
0374, 0380, 0382, 0386, 0388, 0399, 0402, 0415, 0420, 0424, 0426, 0432, 0434, 0446,
0450, 0482
350-1041
ON A/C 0005-0058, 0060-0064, 0066-0070, 0072-0087, 0089-0101, 0103-0107, 0109, 0111-
0117, 0119-0124, 0126-0130, 0132-0138, 0140, 0142-0151, 0153-0155, 0157-0160, 0162-
0165, 0167, 0168, 0170, 0172-0187, 0189-0193, 0195-0205, 0207-0214, 0216-0221, 0223,
0224, 0226-0228, 0230-0232, 0234-0240, 0243-0251, 0254-0257, 0259-0261, 0263-0265,
0267-0269, 0271-0273, 0276-0282, 0284, 0285, 0287, 0289, 0291-0295, 0297, 0299-0303,
0305, 0307-0314, 0316, 0318, 0320-0325, 0327-0329, 0331, 0333-0335, 0337-0339, 0341,
0343-0345, 0347-0349, 0351, 0352, 0354, 0355, 0357-0359, 0363-0366, 0369-0371, 0373,
0375, 0376, 0378, 0379, 0381, 0383, 0385, 0387, 0389-0392, 0394-0398, 0400, 0401, 0403-
0408, 0410-0414, 0416, 0418, 0419, 0421-0423, 0425, 0427-0429, 0431, 0433, 0435-0437,
0439, 0441-0443, 0445, 0447-0449, 0451-0455, 0458, 0464, 0465, 0468, 0469, 0472, 0474-
0476, 0479, 0481, 0484, 0488, 0491, 0497, 0500, 0502
350-941
CONF ALL
(2) Applicability by MSN
0005-0058 0060-0107 0109-0130 0132-0138 0140-0151 0153-0155 0157-0165 0167-
0170 0172-0193 0195-0221 0223-0241 0243-0252 0254-0269 0271-0274 0276-0282
0284-0287 0289-0303 0305-0316 0318-0352 0354-0359 0362-0366 0368-0376 0378-
0383 0385-0392 0394-0408 0410-0416 0418-0429 0431-0437 0439 0441-0443 0445-
0455 0458 0464 0465 0468 0469 0472 0474-0476 0479 0481 0482 0484 0488 0491
0497 0500 0502
(3) MSN by configuration
MSN CONFIGURATION
0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015
0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026
0027 0028 0029 0030 0031 0032 0033 0034 0035 0036 0037
0038 0039 0040 0041 0042 0043 0044 0045 0046 0047 0048
0049 0050 0051 0052 0053 0054 0055 0056 0057 0058 0060
0061 0062 0063 0064 0065 0066 0067 0068 0069 0070 0071
0072 0073 0074 0075 0076 0077 0078 0079 0080 0081 0082
0083 0084 0085 0086 0087 0088 0089 0090 0091 0092 0093
0094 0095 0096 0097 0098 0099 0100 0101 0102 0103 0104
0105 0106 0107 0109 0110 0111 0112 0113 0114 0115 0116
0117 0118 0119 0120 0121 0122 0123 0124 0125 0126 0127
0128 0129 0130 0132 0133 0134 0135 0136 0137 0138 0140
0141 0142 0143 0144 0145 0146 0147 0148 0149 0150 0151
0153 0154 0155 0157 0158 0159 0160 0161 0162 0163 0164
0165 0167 0168 0169 0170 0172 0173 0174 0175 0176 0177
002

### Page 10

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 10
MSN CONFIGURATION
0178 0179 0180 0181 0182 0183 0184 0185 0186 0187 0188
0189 0190 0191 0192 0193 0195 0196 0197 0198 0199 0200
0201 0202 0203 0204 0205 0206 0207 0208 0209 0210 0211
0212 0213 0214 0215 0216 0217 0218 0219 0220 0221 0223
0224 0225 0226 0227 0228 0229 0230 0231 0232 0233 0234
0235 0236 0237 0238 0239 0240 0241 0243 0244 0245 0246
0247 0248 0249 0250 0251 0252 0254 0255 0256 0257 0258
0259 0260 0261 0262 0263 0264 0265 0266 0267 0268 0269
0271 0272 0273 0274 0276 0277 0278 0279 0280 0281 0282
0284 0285 0286 0287 0289 0290 0291 0292 0293 0294 0295
0296 0297 0298 0299 0300 0301 0302 0303 0305 0306 0307
0308 0309 0310 0311 0312 0313 0314 0315 0316 0318 0319
0320 0321 0322 0323 0324 0325 0326 0327 0328 0329 0330
0331 0332 0333 0334 0335 0336 0337 0338 0339 0340 0341
0342 0343 0344 0345 0346 0347 0348 0349 0350 0351 0352
0354 0355 0356 0357 0358 0359 0362 0363 0364 0365 0366
0368 0369 0370 0371 0372 0373 0374 0375 0376 0378 0379
0380 0381 0382 0383 0385 0386 0387 0388 0389 0390 0391
0392 0394 0395 0396 0397 0398 0399 0400 0401 0402 0403
0404 0405 0406 0407 0408 0410 0411 0412 0413 0414 0415
0416 0418 0419 0420 0421 0422 0423 0424 0425 0426 0427
0428 0429 0431 0432 0433 0434 0435 0436 0437 0439 0441
0442 0443 0445 0446 0447 0448 0449 0450 0451 0452 0453
0454 0455 0458 0464 0465 0468 0469 0472 0474 0475 0476
0479 0481 0482 0484 0488 0491 0497 0500 0502
(4) Configuration definition
Configuration 002
CONF 002 is applicable for all the aircraft affected by this Service Bulletin as a
standard configuration.
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
STELIA reported to Airbus that A350 Captain (CAPT), First Officer (F/O) and 3rd
Occupant TAAI8 Series seats may be subject to a potential failure of the Vertical Stop
Support Fitting (VSSF). Without the Stop Block, the seat might disconnect from the
seat low column.
(2) Objective/Action
This Service Bulletin is published to advise the operators of the affected Manufacturer
Serial Numbers (MSNs) to inspect the VSSF .
(3) Advantages
The accomplishment of this Service Bulletin ensures the dispatch reliability of the
A350 aircraft.
(4) Operational/Maintenance Consequences
None

### Page 11

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 11
D. DESCRIPTION
T o accomplish this Service Bulletin it is necessary to:
(1) Do the Inspection of the Cockpit Seat(s)
(a) T ask set A350-A-25-XX-P122-01000-93BA-A Do the Inspection of the Cockpit
Seat(s)
1 Do the Inspection of the CAPT, F/O and 3rd Occupant Cockpit Seats
(2) Do the Repair of the Affected Cockpit Seat(s) in accordance with VSB
(Depending on the Inspection Result)
(a) T ask set A350-A-25-XX-P122-01000-93AA-A Do the Repair of the Affected Cockpit
Seat(s) in accordance with VSB (Depending on the Inspection Result)
1 Remove the CAPT seat (Depending on the Inspection Result)
2 Do the Repair of the CAPT Seat on Bench (Depending on the Inspection
Result)
3 Install the CAPT Seat (Depending on the Inspection Result)
4 Remove the F/O Seat (Depending on the Inspection Result)
5 Do the Repair of the F/O Seat (Depending on the Inspection Result)
6 Install the F/O Seat (Depending on the Inspection Result)
7 Remove the 3rd Occupant Seat (Depending on the Inspection Result)
8 Do the Repair of the 3rd Occupant (Depending on the Inspection Result)
9 Install the 3rd Occupant Seat (Depending on the Inspection Result)
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
This Service Bulletin has been classified Mandatory. It is expected that an
Airworthiness Directive (AD) published by the European Union Aviation Safety Agency
(EASA) will be issued to confirm this classification. It is anticipated that the AD will
confirm the thresholds given but reference should be made to the AD for confirmation
of the mandated accomplishment timescale.
Accomplishment of this Service Bulletin must be done in accordance with the table
below.
T able 2, Config. 002 — Do the Inspection of the Cockpit Seats
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
All aircraft Inspect the
CAPT, F/O and
3rd occupant
seats P/N and S/
N and check if
they are affected
by the repair
in accordance
with Subtask
Within 36
month(s)
from Service
Bulletin issuance
None None

### Page 12

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 12
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
Ref. T ask A350-
A-25-XX-P122-
03ZZZ-300Z-A
Seat(s) P/N and
S/N affected
by the repair
refer to T able 4 Before next
Flight Cycle(s)
None None
Seat(s) P/N and
S/N not affected
by the repair
Send the
inspection report
to AIRBUS.
Then, no further
action with this
Service Bulletin
Within 90
day(s) from SB
embodiment
None None
T able 4, Config. 001 thru Config. 003 — Do the Repair of the Affected Cockpit Seat(s)
in accordance with VSB (Depending on the Inspection Result)
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
Seat(s) P/N and
S/N affected
by the repair
Remove, repair
and install again
the affected
seat(s) in
accordance
with Ref. T ask
set A350-A-
25-XX-P122-
01ZZZ-93AZ-A
Within 36
month(s)
from Service
Bulletin issuance
None None
Seat(s) P/N and
S/N affected
by the repair
Send the
inspection
report to AIRBUS
None None None
F. APPROVAL
The technical content of this document is approved under the authority of the Design
Organisation Approval ref. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Do the Inspection of the Cockpit Seat(s)
(a) T ask set A350-A-25-XX-P122-01000-93BA-A Do the Inspection of the Cockpit
Seat(s)
PREPARATION

### Page 13

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 13
Job Set-up 0.50 h
PROCEDURE
Do the Inspection of the CAPT, F/O and 3rd Occupant
Cockpit Seats
0.40 h
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Close-up 0.50 h
TOTAL MAN-HOURS 1.40 h
ELAPSED TIME (HOURS) 1.40 h
NOTE: The minimum man-hours necessary to accomplish this Service Bulletin
are those for the Inspection. Depending on the inspection result,
additional man-hours can apply.
(2) Do the Repair of the Affected Cockpit Seat(s) in accordance with VSB
(Depending on the Inspection Result)
(a) T ask set A350-A-25-XX-P122-01000-93AA-A Do the Repair of the Affected Cockpit
Seat(s) in accordance with VSB (Depending on the Inspection Result)
PREPARATION
Job Set-up 0.50 h
PROCEDURE
Remove the CAPT seat (Depending on the Inspection
Result)
2.00 h
Install the CAPT Seat (Depending on the Inspection Result) 3.00 h
Remove the F/O Seat (Depending on the Inspection Result) 2.00 h
Install the F/O Seat (Depending on the Inspection Result) 3.00 h
Remove the 3rd Occupant Seat (Depending on the
Inspection Result)
1.00 h
Install the 3rd Occupant Seat (Depending on the Inspection
Result)
1.50 h
PREPARATION FOR TEST
Job Set-Up for T est 0.25 h
TEST
T esting 0.30 h
CLOSE-UP
Close-up 0.50 h
TOTAL MAN-HOURS 14.05 h
ELAPSED TIME (HOURS) 7.45 h
Additional man-hours related to Vendor SB; refer to:
Do the Repair of the CAPT Seat on Bench
(Depending on the Inspection Result)
Ref. STELIA AEROSPACE (F4643)
VSB TAAI8-25-1197
BENCH
Do the Repair of the F/O Seat
(Depending on the Inspection Result)
Ref. STELIA AEROSPACE (F4643)
VSB TAAI8-25-1197
BENCH

### Page 14

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 14
Do the Repair of the 3rd Occupant
(Depending on the Inspection Result)
Ref. STELIA AEROSPACE (F4643)
VSB TAAI8-25-1199
BENCH
H. WEIGHT AND BALANCE
Not changed
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
(1) Do the Inspection of the Cockpit Seat(s)
(a) T ask set A350-A-25-XX-P122-01000-93BA-A Do the Inspection of the Cockpit
Seat(s)
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
INTRODUCTION (INTRO)
A350-A-00-6X-XX-11ZZZ-018Z-D
IN SERVICE INFORMATION (ISI)
00.00.00179
SYSTEM DESCRIPTION (SD)
A350-A-06-3X-XX-01ZZZ-04CZ-A
VENDOR SERVICE BULLETIN (VSB)
STELIA AEROSPACE (F4643) VSB TAAI8-25-1197
STELIA AEROSPACE (F4643) VSB TAAI8-25-1199
(2) Do the Repair of the Affected Cockpit Seat(s) in accordance with VSB
(Depending on the Inspection Result)
(a) T ask set A350-A-25-XX-P122-01000-93AA-A Do the Repair of the Affected Cockpit
Seat(s) in accordance with VSB (Depending on the Inspection Result)
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
INTRODUCTION (INTRO)
A350-A-00-6X-XX-11ZZZ-018Z-D
IN SERVICE INFORMATION (ISI)
00.00.00179
MAINTENANCE PROCEDURE (MP)
A350-A-24-41-XX-00ZZZ-170Z-A A350-A-25-11-46-00ZZZ-520Z-A
A350-A-25-11-46-00ZZZ-720Z-A
A350-A-25-11-47-00ZZZ-520Z-A
A350-A-25-11-47-00ZZZ-720Z-A

### Page 15

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 15
SYSTEM DESCRIPTION (SD)
A350-A-06-3X-XX-01ZZZ-04CZ-A
VENDOR SERVICE BULLETIN (VSB)
STELIA AEROSPACE (F4643) VSB TAAI8-25-1197
STELIA AEROSPACE (F4643) VSB TAAI8-25-1199
K. PUBLICATION AFFECTED
None
L. INDUSTRY SUPPORT INFORMATION
Refer to the Service Bulletin No. Ref. STELIA AEROSPACE (F4643) VSB TAAI8-25-1197 and
Ref. STELIA AEROSPACE (F4643) VSB TAAI8-25-1199 for the industry support terms of the
Vendor Service Bulletin parts and labor.
Industry support terms for the equipment must be negotiated with the equipment supplier.
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department: monitored.retrofit@airbus.com.

### Page 16

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 16
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
No material for task set A350-A-25-XX-P122-01000-93BA-A Do the Inspection of
the Cockpit Seat(s)
Material for task set A350-A-25-XX-P122-01000-93AA-A Do the Repair of the
Affected Cockpit Seat(s) in accordance with VSB (Depending on the Inspection
Result)
MATERIAL QTY SEE NOTES
Referenced tools See SB
Referenced parts See SB
B. TOOLING
Referenced tools for task set A350-A-25-XX-P122-01000-93AA-A Do the Repair
of the Affected Cockpit Seat(s) in accordance with VSB (Depending on the
Inspection Result)
T o accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. STELIA AEROSPACE (F4643) VSB TAAI8-25-1197
Ref. STELIA AEROSPACE (F4643) VSB TAAI8-25-1199
C. CONSUMABLES
No consumables
D. LIST OF NEW PARTS
Referenced parts for task set A350-A-25-XX-P122-01000-93AA-A Do the Repair
of the Affected Cockpit Seat(s) in accordance with VSB (Depending on the
Inspection Result)
T o accomplish this Service Bulletin it is necessary to use the expendable parts listed in:
Ref. STELIA AEROSPACE (F4643) VSB TAAI8-25-1197
Ref. STELIA AEROSPACE (F4643) VSB TAAI8-25-1199
E. LIST OF EXISTING PARTS
No parts

### Page 17

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 17
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A350-A-25-XX-P122-01000-93BA-A (A350-A-25-XX-P122-01ZZZ-93BZ-A)
Do the Inspection of the Cockpit Seat(s)
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESP A350-A-20-55-XX-01ZZZ-
042Z-A.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including Required for Compliance paragraph
contained herein, contact AIRBUS for further instructions and approval.
NOTE: Discarded parts must be managed at the operator's discretion.
NOTE: The purpose of flowcharts is to supplement the information given in the Procedure and
Compliance paragraphs and not to serve as the primary source for tasks or compliance
times given in this Service Bulletin.

### Page 18

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 18
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
TOTAL MAN-HOURS 1.40 h
ELAPSED TIME (HOURS) 1.40 h
B. PREPARATION
(1) Task A350-A-25-XX-P122-01001-540A-A (A350-A-25-XX-P122-01ZZZ-540Z-A)
Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
INTRO A350-A-00-6X-XX-11ZZZ-018Z-D
Procedure
NOTE: For the basic Aircraft configuration, refer to Ref. INTRO A350-A-00-6X-XX-
11ZZZ-018Z-D “Maintenance Procedure - Introduction”.
C. PROCEDURE
(1) Task A350-A-25-XX-P122-03001-300A-A (A350-A-25-XX-P122-03ZZZ-300Z-A)
Do the Inspection of the CAPT, F/O and 3rd Occupant Cockpit Seats
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
210
Manpower/Resources/Skills
Man-hours 0.40 h
Minimum Number of person 1
Elapsed Time 0.40 h
Referenced Information
Manuals/Drawings References/Sheets
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
ISI 00.00.00179
VSB
STELIA AEROSPACE (F4643) VSB TAAI8-25-
1197
STELIA AEROSPACE (F4643) VSB TAAI8-25-
1199
Procedure
(a) Standard Practices

### Page 19

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 19
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
(b) At the threshold given in the PLANNING INFORMATION PARAGRAPH E (2):
Inspect the CAPT , F/O and 3rd occupant P/N and S/N on the seats identification
plate.
Refer to Ref. Fig.FA Flow Chart
1 Check if the P/N and S/N of the CAPT seat are affected by the repair in
accordance with the list given in the Ref. STELIA AEROSPACE (F4643) VSB
TAAI8-25-1197.
a If the P/N and S/N of the CAPT seat are affected:
<1> Do the repair of the seat in accordance with Ref. T ask set A350-
A-25-XX-P122-01ZZZ-93AZ-A.
<2> Go to next step.
b If the P/N and S/N of the CAPT seat are not affected:
<1> Go to next step.
2 Check if the P/N and S/N of the F/O seat are affected by the repair in
accordance with the list given in the Ref. STELIA AEROSPACE (F4643) VSB
TAAI8-25-1197.
a If the P/N and S/N of the F/O seat are affected:
<1> Do the repair of the seat in accordance with Ref. T ask set A350-
A-25-XX-P122-01ZZZ-93AZ-A.
<2> Go to next step.
b If the P/N and S/N of the F/O seat are not affected:
<1> Go to next step.
3 Check if the P/N and S/N of the 3rd occupant seat are affected by the repair
in accordance with the list given in the Ref. STELIA AEROSPACE (F4643)
VSB TAAI8-25-1199.
a If the P/N and S/N of the 3rd occupant seat are affected:
<1> Do the repair of the seat in accordance with Ref. T ask set A350-
A-25-XX-P122-01ZZZ-93AZ-A.
<2> Go to next step.
b If the P/N and S/N of the 3rd occupant seat are not affected:
<1> Go to next step.
4 Upload the completed Inspection Report sheet given in Ref. Appendix
Inspection Report in accordance with Ref. ISI 00.00.00179.
NOTE: Uploading the Inspection Report sheet is not Required for
Compliance.
5 No further action.

### Page 20

A350
SERVICE BULLETIN
Figure ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01 Fig.FA Sol.AB SHEET 1/1
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21
Flow Chart
Page 20
CONF ALL
YES
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2),
REMOVE, REPAIR AND INSTALL AGAIN THE AFFECTED SEAT IN ACCORDANCE
WITH TASK A350-A-25-XX-P122-01000-93AA-A
SEND THE INSPECTION
REPORT TO AIRBUS
OTHER SEAT
AFFECTED?
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
NO
YES
SEAT P/N & S/N
AFFECTED BY THE
REPAIR?
NO
CAPT, F/O AND THIRD OCCUPANT SEATS P/N AND S/N AND CHECK IF THEY ARE AFFECTED
BY THE REPAIR IN ACCORDANCE WITH SUBTASK A350-A-25-XX-P122-03001-300A-A
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2), INSPECT THE
NOTE:
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01

### Page 21

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 21
D. PREPARATION FOR TEST
None
E. TEST
None
F. CLOSE-UP
(1) Task A350-A-25-XX-P122-01001-740A-A (A350-A-25-XX-P122-01ZZZ-740Z-A)
Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Procedure
NOTE: If you intend to accomplish an associated Repair T ask during the same layover
period, the subsequent Close-up procedure is not necessary.
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A350-A-25-XX-P122-01001-90AA-A (A350-A-25-XX-P122-01ZZZ-90AZ-A)
Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 22

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 22
Task set A350-A-25-XX-P122-01000-93AA-A (A350-A-25-XX-P122-01ZZZ-93AZ-A)
Do the Repair of the Affected Cockpit Seat(s) in accordance with VSB (Depending on the
Inspection Result)
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESP A350-A-20-55-XX-01ZZZ-
042Z-A.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including Required for Compliance paragraph
contained herein, contact AIRBUS for further instructions and approval.
NOTE: Discarded parts must be managed at the operator's discretion.
NOTE: The purpose of flowcharts is to supplement the information given in the Procedure and
Compliance paragraphs and not to serve as the primary source for tasks or compliance
times given in this Service Bulletin.

### Page 23

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 23
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
TOTAL MAN-HOURS 14.05 h
ELAPSED TIME (HOURS) 7.45 h
Additional man-hours related to Vendor SB; refer to:
STELIA AEROSPACE (F4643) VSB TAAI8-25-1197
STELIA AEROSPACE (F4643) VSB TAAI8-25-1199
B. PREPARATION
(1) Task A350-A-25-XX-P122-02002-540A-A (A350-A-25-XX-P122-02ZZZ-540Z-A)
Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
INTRO A350-A-00-6X-XX-11ZZZ-018Z-D
MP
A350-A-24-41-XX-00ZZZ-170Z-A
A350-A-25-11-46-00ZZZ-520Z-A
A350-A-25-11-47-00ZZZ-520Z-A
Procedure
NOTE: If you intend to accomplish this Repair during the same layover period as the
associated Inspection, the subsequent Preparation procedure is not necessary.
NOTE: For the basic Aircraft configuration, refer to Ref. INTRO A350-A-00-6X-XX-
11ZZZ-018Z-D “Maintenance Procedure - Introduction”.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. MP A350-A-24-
41-XX-00ZZZ-170Z-A.
(b) Do the job set-up procedure as specified in the removal of the CAPT seat, refer to
Ref. MP A350-A-25-11-46-00ZZZ-520Z-A (depending on the inspection result).
(c) Do the job set-up procedure as specified in the removal of the F/O seat, refer to
Ref. MP A350-A-25-11-46-00ZZZ-520Z-A (depending on the inspection result).
(d) Do the job set-up procedure as specified in the removal of the 3rd occupant seat,
refer to Ref. MP A350-A-25-11-47-00ZZZ-520Z-A (depending on the inspection
result).
C. PROCEDURE
(1) Task A350-A-25-XX-P122-01001-520A-A (A350-A-25-XX-P122-01ZZZ-520Z-A)
Remove the CAPT seat (Depending on the Inspection Result)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
210

### Page 24

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 24
Manpower/Resources/Skills
Man-hours 2.00 h
Minimum Number of person 2
Elapsed Time 1.00 h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-25-11-46-00ZZZ-520Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard Practices
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
(b) At the threshold given in the PLANNING INFORMATION PARAGRAPH E (2):
Remove and retain for modification the CAPT seat, refer to Ref. MP A350-A-25-
11-46-00ZZZ-520Z-A.
NOTE: Installation of the seat equipment after the removal of the seat from the
cockpit as given in the step 9) of Ref. MP A350-A-25-11-46-00ZZZ-520Z-
A is not necessary.
(2) Task A350-A-25-XX-P122-01001-690A-C (A350-A-25-XX-P122-01ZZZ-690Z-C)
Do the Repair of the CAPT Seat on Bench (Depending on the Inspection
Result)
Job Set-Up Information
Manpower/Resources/Skills
Man-hours
Minimum Number of person
Elapsed Time
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
VSB STELIA AEROSPACE (F4643) VSB TAAI8-25-1197
Procedure
Refer to Ref. Fig.FA Flow Chart
(a) At the threshold given in the PLANNING INFORMATION PARAGRAPH E (2):
Do the repair of the CAPT seat in accordance with Ref. STELIA AEROSPACE
(F4643) VSB TAAI8-25-1197.
(b) Modify the CAPT seat identification in accordance with Ref. STELIA AEROSPACE
(F4643) VSB TAAI8-25-1197.

### Page 25

A350
SERVICE BULLETIN
Figure ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01 Fig.FA Sol.AB SHEET 1/1
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21
Flow Chart
Page 25
CONF ALL
YES
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2),
REMOVE, REPAIR AND INSTALL AGAIN THE AFFECTED SEAT IN ACCORDANCE
WITH TASK A350-A-25-XX-P122-01000-93AA-A
SEND THE INSPECTION
REPORT TO AIRBUS
OTHER SEAT
AFFECTED?
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
NO
YES
SEAT P/N & S/N
AFFECTED BY THE
REPAIR?
NO
CAPT, F/O AND THIRD OCCUPANT SEATS P/N AND S/N AND CHECK IF THEY ARE AFFECTED
BY THE REPAIR IN ACCORDANCE WITH SUBTASK A350-A-25-XX-P122-03001-300A-A
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2), INSPECT THE
NOTE:
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01

### Page 26

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 26
(3) Task A350-A-25-XX-P122-01001-720A-A (A350-A-25-XX-P122-01ZZZ-720Z-A)
Install the CAPT Seat (Depending on the Inspection Result)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
210
Manpower/Resources/Skills
Man-hours 3.00 h
Minimum Number of person 2
Elapsed Time 1.50 h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-25-11-46-00ZZZ-720Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
ISI 00.00.00179
Procedure
Refer to Ref. Fig.FA Flow Chart
(a) Standard Practices
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
(b) At the threshold given in the PLANNING INFORMATION PARAGRAPH E (2):
Install the modified CAPT seat, refer to Ref. MP A350-A-25-11-46-00ZZZ-720Z-A.
(c) Upload the completed Inspection Report sheet given in Ref. Appendix Inspection
Report in accordance with Ref. ISI 00.00.00179.
NOTE: Uploading the Inspection Report sheet is not Required for Compliance.

### Page 27

A350
SERVICE BULLETIN
Figure ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01 Fig.FA Sol.AB SHEET 1/1
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21
Flow Chart
Page 27
CONF ALL
YES
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2),
REMOVE, REPAIR AND INSTALL AGAIN THE AFFECTED SEAT IN ACCORDANCE
WITH TASK A350-A-25-XX-P122-01000-93AA-A
SEND THE INSPECTION
REPORT TO AIRBUS
OTHER SEAT
AFFECTED?
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
NO
YES
SEAT P/N & S/N
AFFECTED BY THE
REPAIR?
NO
CAPT, F/O AND THIRD OCCUPANT SEATS P/N AND S/N AND CHECK IF THEY ARE AFFECTED
BY THE REPAIR IN ACCORDANCE WITH SUBTASK A350-A-25-XX-P122-03001-300A-A
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2), INSPECT THE
NOTE:
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01

### Page 28

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 28
(4) Task A350-A-25-XX-P122-03001-520A-A (A350-A-25-XX-P122-03ZZZ-520Z-A)
Remove the F/O Seat (Depending on the Inspection Result)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
210
Manpower/Resources/Skills
Man-hours 2.00 h
Minimum Number of person 2
Elapsed Time 1.00 h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-25-11-46-00ZZZ-520Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
Refer to Ref. Fig.FA Flow Chart
(a) Standard Practices
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
(b) At the threshold given in the PLANNING INFORMATION PARAGRAPH E (2):
Remove and retain for modification the F/O seat, refer to Ref. MP A350-A-25-11-
46-00ZZZ-520Z-A.
NOTE: Installation of the seat equipment after the removal of the seat from the
cockpit as given in the step 9) of Ref. MP A350-A-25-11-46-00ZZZ-520Z-
A is not necessary.

### Page 29

A350
SERVICE BULLETIN
Figure ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01 Fig.FA Sol.AB SHEET 1/1
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21
Flow Chart
Page 29
CONF ALL
YES
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2),
REMOVE, REPAIR AND INSTALL AGAIN THE AFFECTED SEAT IN ACCORDANCE
WITH TASK A350-A-25-XX-P122-01000-93AA-A
SEND THE INSPECTION
REPORT TO AIRBUS
OTHER SEAT
AFFECTED?
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
NO
YES
SEAT P/N & S/N
AFFECTED BY THE
REPAIR?
NO
CAPT, F/O AND THIRD OCCUPANT SEATS P/N AND S/N AND CHECK IF THEY ARE AFFECTED
BY THE REPAIR IN ACCORDANCE WITH SUBTASK A350-A-25-XX-P122-03001-300A-A
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2), INSPECT THE
NOTE:
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01

### Page 30

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 30
(5) Task A350-A-25-XX-P122-02001-690A-C (A350-A-25-XX-P122-02ZZZ-690Z-C)
Do the Repair of the F/O Seat (Depending on the Inspection Result)
Job Set-Up Information
Manpower/Resources/Skills
Man-hours
Minimum Number of person
Elapsed Time
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
VSB STELIA AEROSPACE (F4643) VSB TAAI8-25-1197
Procedure
Refer to Ref. Fig.FA Flow Chart
(a) At the threshold given in the PLANNING INFORMATION PARAGRAPH E (2):
Do the repair of the F/O seat in accordance with Ref. STELIA AEROSPACE (F4643)
VSB TAAI8-25-1197.
(b) Modify the F/O seat identification in accordance with Ref. STELIA AEROSPACE
(F4643) VSB TAAI8-25-1197.

### Page 31

A350
SERVICE BULLETIN
Figure ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01 Fig.FA Sol.AB SHEET 1/1
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21
Flow Chart
Page 31
CONF ALL
YES
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2),
REMOVE, REPAIR AND INSTALL AGAIN THE AFFECTED SEAT IN ACCORDANCE
WITH TASK A350-A-25-XX-P122-01000-93AA-A
SEND THE INSPECTION
REPORT TO AIRBUS
OTHER SEAT
AFFECTED?
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
NO
YES
SEAT P/N & S/N
AFFECTED BY THE
REPAIR?
NO
CAPT, F/O AND THIRD OCCUPANT SEATS P/N AND S/N AND CHECK IF THEY ARE AFFECTED
BY THE REPAIR IN ACCORDANCE WITH SUBTASK A350-A-25-XX-P122-03001-300A-A
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2), INSPECT THE
NOTE:
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01

### Page 32

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 32
(6) Task A350-A-25-XX-P122-02001-720A-A (A350-A-25-XX-P122-02ZZZ-720Z-A)
Install the F/O Seat (Depending on the Inspection Result)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
210
Manpower/Resources/Skills
Man-hours 3.00 h
Minimum Number of person 2
Elapsed Time 1.50 h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-25-11-46-00ZZZ-720Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
ISI 00.00.00179
Procedure
Refer to Ref. Fig.FA Flow Chart
(a) Standard Practices
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
(b) At the threshold given in the PLANNING INFORMATION PARAGRAPH E (2):
Install the modified F/O seat, refer to Ref. MP A350-A-25-11-46-00ZZZ-720Z-A.
(c) Upload the completed Inspection Report sheet given in Ref. Appendix Inspection
Report in accordance with Ref. ISI 00.00.00179.
NOTE: Uploading the Inspection Report sheet is not Required for Compliance.

### Page 33

A350
SERVICE BULLETIN
Figure ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01 Fig.FA Sol.AB SHEET 1/1
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21
Flow Chart
Page 33
CONF ALL
YES
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2),
REMOVE, REPAIR AND INSTALL AGAIN THE AFFECTED SEAT IN ACCORDANCE
WITH TASK A350-A-25-XX-P122-01000-93AA-A
SEND THE INSPECTION
REPORT TO AIRBUS
OTHER SEAT
AFFECTED?
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
NO
YES
SEAT P/N & S/N
AFFECTED BY THE
REPAIR?
NO
CAPT, F/O AND THIRD OCCUPANT SEATS P/N AND S/N AND CHECK IF THEY ARE AFFECTED
BY THE REPAIR IN ACCORDANCE WITH SUBTASK A350-A-25-XX-P122-03001-300A-A
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2), INSPECT THE
NOTE:
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01

### Page 34

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 34
(7) Task A350-A-25-XX-P122-04001-520A-A (A350-A-25-XX-P122-04ZZZ-520Z-A)
Remove the 3rd Occupant Seat (Depending on the Inspection Result)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
210
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 2
Elapsed Time 0.50 h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-25-11-47-00ZZZ-520Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
Refer to Ref. Fig.FA Flow Chart
(a) Standard Practices
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
(b) At the threshold given in the PLANNING INFORMATION PARAGRAPH E (2):
Remove and retain for modification the 3rd occupant seat, refer to Ref. MP A350-
A-25-11-47-00ZZZ-520Z-A.
NOTE: Installation of the seat equipment after the removal of the seat from the
cockpit as given in the step 6) of Ref. MP A350-A-25-11-47-00ZZZ-520Z-
A is not necessary.

### Page 35

A350
SERVICE BULLETIN
Figure ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01 Fig.FA Sol.AB SHEET 1/1
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21
Flow Chart
Page 35
CONF ALL
YES
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2),
REMOVE, REPAIR AND INSTALL AGAIN THE AFFECTED SEAT IN ACCORDANCE
WITH TASK A350-A-25-XX-P122-01000-93AA-A
SEND THE INSPECTION
REPORT TO AIRBUS
OTHER SEAT
AFFECTED?
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
NO
YES
SEAT P/N & S/N
AFFECTED BY THE
REPAIR?
NO
CAPT, F/O AND THIRD OCCUPANT SEATS P/N AND S/N AND CHECK IF THEY ARE AFFECTED
BY THE REPAIR IN ACCORDANCE WITH SUBTASK A350-A-25-XX-P122-03001-300A-A
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2), INSPECT THE
NOTE:
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01

### Page 36

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 36
(8) Task A350-A-25-XX-P122-03001-690A-C (A350-A-25-XX-P122-03ZZZ-690Z-C)
Do the Repair of the 3rd Occupant (Depending on the Inspection Result)
Job Set-Up Information
Manpower/Resources/Skills
Man-hours
Minimum Number of person
Elapsed Time
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
VSB STELIA AEROSPACE (F4643) VSB TAAI8-25-1199
Procedure
Refer to Ref. Fig.FA Flow Chart
(a) At the threshold given in the PLANNING INFORMATION PARAGRAPH E (2):
Do the repair of the 3rd occupant seat in accordance with Ref. STELIA
AEROSPACE (F4643) VSB TAAI8-25-1199.
(b) Modify the 3rd occupant seat identification in accordance with Ref. STELIA
AEROSPACE (F4643) VSB TAAI8-25-1199.

### Page 37

A350
SERVICE BULLETIN
Figure ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01 Fig.FA Sol.AB SHEET 1/1
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21
Flow Chart
Page 37
CONF ALL
YES
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2),
REMOVE, REPAIR AND INSTALL AGAIN THE AFFECTED SEAT IN ACCORDANCE
WITH TASK A350-A-25-XX-P122-01000-93AA-A
SEND THE INSPECTION
REPORT TO AIRBUS
OTHER SEAT
AFFECTED?
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
NO
YES
SEAT P/N & S/N
AFFECTED BY THE
REPAIR?
NO
CAPT, F/O AND THIRD OCCUPANT SEATS P/N AND S/N AND CHECK IF THEY ARE AFFECTED
BY THE REPAIR IN ACCORDANCE WITH SUBTASK A350-A-25-XX-P122-03001-300A-A
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2), INSPECT THE
NOTE:
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01

### Page 38

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 38
(9) Task A350-A-25-XX-P122-03001-720A-A (A350-A-25-XX-P122-03ZZZ-720Z-A)
Install the 3rd Occupant Seat (Depending on the Inspection Result)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
210
Manpower/Resources/Skills
Man-hours 1.50 h
Minimum Number of person 2
Elapsed Time 0.75 h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-25-11-47-00ZZZ-720Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
ISI 00.00.00179
Procedure
Refer to Ref. Fig.FA Flow Chart
(a) Standard Practices
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
(b) At the threshold given in the PLANNING INFORMATION PARAGRAPH E (2):
Install the modified 3rd occupant seat, refer to Ref. MP A350-A-25-11-47-00ZZZ-
720Z-A.
(c) Upload the completed Inspection Report sheet given in Ref. Appendix Inspection
Report in accordance with Ref. ISI 00.00.00179.
NOTE: Uploading the Inspection Report sheet is not Required for Compliance.

### Page 39

A350
SERVICE BULLETIN
Figure ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01 Fig.FA Sol.AB SHEET 1/1
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21
Flow Chart
Page 39
CONF ALL
YES
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2),
REMOVE, REPAIR AND INSTALL AGAIN THE AFFECTED SEAT IN ACCORDANCE
WITH TASK A350-A-25-XX-P122-01000-93AA-A
SEND THE INSPECTION
REPORT TO AIRBUS
OTHER SEAT
AFFECTED?
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
NO
YES
SEAT P/N & S/N
AFFECTED BY THE
REPAIR?
NO
CAPT, F/O AND THIRD OCCUPANT SEATS P/N AND S/N AND CHECK IF THEY ARE AFFECTED
BY THE REPAIR IN ACCORDANCE WITH SUBTASK A350-A-25-XX-P122-03001-300A-A
AT THE THRESHOLD GIVEN IN THE PLANNING INFORMATION PARAGRAPH E.(2), INSPECT THE
NOTE:
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN ICN-A350-A-25XXP122-A-FAPE3-046YO-A-002-01

### Page 40

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 40
D. PREPARATION FOR TEST
(1) Task A350-A-25-XX-P122-03002-540A-A (A350-A-25-XX-P122-03ZZZ-540Z-A)
Job Set-Up for Test
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Skills Electrical
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-25-11-46-00ZZZ-720Z-AA350-A-25-11-47-00ZZZ-720Z-A
Procedure
(a) If necessary, remove the Safety clips and tags and close the circuit breakers as
specified after the installation of the CAPT seat, refer to Ref. MP A350-A-25-11-
46-00ZZZ-720Z-A.
(b) If necessary, remove the Safety clips and tags and close the circuit breakers as
specified after the installation of the F/O seat, refer to Ref. MP A350-A-25-11-46-
00ZZZ-720Z-A.
(c) If necessary, remove the Safety clips and tags and close the circuit breakers as
specified after the installation of the 3rd occupant seat, refer to Ref. MP A350-A-
25-11-47-00ZZZ-720Z-A.
E. TEST
(1) Task A350-A-25-XX-P122-01002-320A-A (A350-A-25-XX-P122-01ZZZ-320Z-A)
Testing
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.30 h
Minimum Number of person 1
Elapsed Time 0.30 h
Skills Electrical
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-25-11-46-00ZZZ-720Z-AA350-A-25-11-47-00ZZZ-720Z-A
Procedure
(a) If modified, do the test after the installation of the CAPT seat, refer to Ref. MP
A350-A-25-11-46-00ZZZ-720Z-A.
(b) If modified, do the test after the installation of the F/O seat, refer to Ref. MP
A350-A-25-11-46-00ZZZ-720Z-A.

### Page 41

A350
SERVICE BULLETIN
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 41
(c) If modified, do the test after the installation of the 3rd occupant seat, refer to
Ref. MP A350-A-25-11-47-00ZZZ-720Z-A.
F. CLOSE-UP
(1) Task A350-A-25-XX-P122-02002-740A-A (A350-A-25-XX-P122-02ZZZ-740Z-A)
Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-25-11-46-00ZZZ-720Z-AA350-A-25-11-47-00ZZZ-720Z-A
Procedure
(a) If modified, do the close-up procedure as specified after installation of the CAPT
seat, refer to Ref. MP A350-A-25-11-46-00ZZZ-720Z-A.
(b) If modified, do the close-up procedure as specified after installation of the F/O
seat, refer to Ref. MP A350-A-25-11-46-00ZZZ-720Z-A.
(c) If modified, do the close-up procedure as specified after installation of the 3rd
occupant seat, refer to Ref. MP A350-A-25-11-47-00ZZZ-720Z-A.
(d) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(e) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A350-A-25-XX-P122-02001-90AA-A (A350-A-25-XX-P122-02ZZZ-90AZ-A)
Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 42

A350
SERVICE BULLETIN
APPENDIX
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 42
APPENDIX
A. Inspection Report
Inspection Report
The results of the inspection, including no findings, must be uploaded in accordance with ISI
00.00.00179.

### Page 43

A350
SERVICE BULLETIN
APPENDIX
Figure ICN-A350-A-25XXP122-A-FAPE3-046YF-A-001-01 Fig.AB Sol.AB SHEET 1/1
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21
Inspection Report
Page 43
CONF ALL
INSPECTION REPORT
SERVICE BULLETIN No :
A/C MSN :
FLIGHT CYCLES :
FLIGHT HOURS :
A350-25-P122
DATE OF INSPECTION :
INSPECTION METHOD : GENERAL VISUAL
INSPECTION
UPLOAD THE COMPLETED INSPECTION REPORT
SHEET IN ACCORDANCE WITH ISI 00.00.00179
CAPTAIN SEAT
SEAT P/N AND S/N
AFFECTED ACTION DONE
YES
NO
SEAT REPAIRED IN ACCORDANCE
WITH VSB TAAI8-25-1197
NO FURTHER ACTION
INSPECTION RESULT:
FIRST OFFICER SEAT
YES
NO
SEAT REPAIRED IN ACCORDANCE
WITH VSB TAAI8-25-1197
NO FURTHER ACTION
3rd OCCUPANT SEAT
YES
NO
SEAT REPAIRED IN ACCORDANCE
WITH VSB TAAI8-25-1199
NO FURTHER ACTION
ICN-A350-A-25XXP122-A-FAPE3-046YF-A-001-01

### Page 44

A350
SERVICE BULLETIN
APPENDIX
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 44
B. REPORTING SHEET
TITLE: EQUIPMENT/FURNISHINGS - COCKPIT SEATS - INSPECTION OF
COCKPIT SEATS STOP SUPPORT FITTING
MODIFICATION No.: None
(1) SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance
and Flight Operations Products if it is duly reported to Airbus.
(2) GENERAL information
The SB Reporting policy is published in ISI 00.00.00135. This document provides
information regarding: the SB Reporting means and benefits, the update of
customized Maintenance Products and customized Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations
Products" for further information on the update of affected Flight Operations Products.
(3) SB Reporting procedure
Standard practice to report SB is to use the online reporting application on
AirbusWorld.
Refer to ISI 00.00.00179:
- For complete information on reporting means to Airbus, Question 2 "What are
the standard practices for SB Reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs,
Question 3 "What about the reporting of prerequisite Service Bulletins?"
NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.

### Page 45

A350
SERVICE BULLETIN
APPENDIX
REV 00 Oct 18/18 A350-25-P122
REV 02 Oct 01/21 Page 45
C. QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin.
The reported data that you provide us will be used to analyse areas of difficulties and to
take corrective action to further improve the quality of our Service Bulletin.
We thank you for the time you have taken in completing this form.
Quality rating of this SB 4 3 2 1
Quality rating of the Accomplishment Instructions 4 3 2 1
Quality rating of the Illustrations 4 3 2 1
Is this SB easy to understand ? Y / N
NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score
If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.
Planning Material Instructions
X Applicability X T ooling X Preparation
X Reason X List of Materials
Operator Supplied
X Mod/Inspection
X Manpower X Kit content X T est
X References X Re-identification X Close-up
X Publication X Illustrations
X Industry Support
Comments :
Operator : Date :
Name/Title
Please return this form to :
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
Or via your Resident Customer Support Office.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
