# Airbus Service Bulletin A350-36-P022

Copy: No revision named ("SB A350-36-P022"), 25 pages: PDF https://openairdocs.org/files/sha256/45/a0/45a0c0d9ece3c53735d2d1179c8f7ae506818621a632e462abb9edc5473d5f62; text https://openairdocs.org/service-documents/airbus/a350-36-p022/file/45a0c0d9ece3.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2020-0965, the docket of AD 2021-08-08. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A350-36-P022
- Page: https://openairdocs.org/service-documents/airbus/a350-36-p022

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2023-06-12](https://openairdocs.org/ad/2023-06-12.md), effective May 18, 2023: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus/a350-36-p022/proposed.md).

## Text (25 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2020-0965, the docket of AD 2021-08-08. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 1
CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
 
The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.
MANDATORY MANDATORY MANDATORY
ATA SYSTEM: 36
TITLE: PNEUMATIC - DISTRIBUTION - INSTALL NEW BLEED DUCT WELDED
ASSEMBLY COMPRISING NEW GIMBAL STANDARD REFERENCE - RHS
MODIFICATION No.:
115148L91116

### Page 2

A350
SERVICE BULLETIN
SUMMARY
REV 00 Jan 17/20 A350-36-P022
Page 2
ATA SYSTEM: 36
TITLE: PNEUMATIC - DISTRIBUTION - INSTALL NEW BLEED DUCT WELDED
ASSEMBLY COMPRISING NEW GIMBAL STANDARD REFERENCE - RHS
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR None
MINOR 115148L91116
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.
B. REASON
(1) History
This Service Bulletin is issued to answer to quality assurance department has
identified that a problem with internal interference of adjacent parts:
- Irregular welding of gimbal ring bush (raised and bumpy weld profile)
- Internal interference between bellows and gimbal rings (resistance between 7°
and 8.5°)
- Damage to the inside diameter of the bellows assy membrane 8.5° gimbal (dent
of outside of bellows).
(2) Objective/Action
This Service Bulletin consists in replacing a bleed air duct assembly containing
modified gimbal Standard (STD) on Right Hand (RH) wing.
(3) Advantages
The accomplishment of this Service Bulletin will improve the gimbal quality.
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE MANDATORY COST SAVING NO
A/C OPERATION
AFFECTED
NO VENDOR SB NO
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD YES

### Page 3

A350
SERVICE BULLETIN
SUMMARY
REV 00 Jan 17/20 A350-36-P022
Page 3
EVALUATION TABLE
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO
NOTE: Service Bulletin must be accomplished.
D. MAINTENANCE CONFIGURATION
No specific aircraft maintenance configuration required.
E. MATERIAL PRICE INFORMATION
(1) Modification
(a) T ask set A350-A-36-XX-P022-01000-93AA-A Modification
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Part kit 36P022C01R01 1 44500.00 USD Duct, E-seal
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
FBU FIN HVN QTR
G. CONCURRENT REQUIREMENTS
None
H. NATURE OF THE WORK
(1) Modification
(a) T ask set A350-A-36-XX-P022-01000-93AA-A Modification
AIRCRAFT YES
EQUIPMENT NO
I. MANPOWER
(1) Modification
(a) T ask set A350-A-36-XX-P022-01000-93AA-A Modification
MANPOWER
TOTAL MAN-HOURS 7.75 h
ELAPSED TIME (HOURS) 5.25 h

### Page 4

A350
SERVICE BULLETIN
SUMMARY
Figure ICN-A350-A-36XXP022-A-FAPE3-05CF6-A-001-01 SHEET 1/1
REV 00 Jan 17/20 A350-36-P022General overview
Page 4
J. GENERAL OVERVIEW
CONF ALL
C
B
Z622 A
A
FRONT SPAR
INBD CLOSING RIB
OUTBD CLOSING RIB
REPLACEMENT DUCT
C
B
622AT
465DR
Z465
ICN-A350-A-36XXP022-A-FAPE3-05CF6-A-001-01

### Page 5

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 5
ATA SYSTEM: 36
TITLE: PNEUMATIC - DISTRIBUTION - INSTALL NEW BLEED DUCT WELDED
ASSEMBLY COMPRISING NEW GIMBAL STANDARD REFERENCE - RHS
1. PLANNING INFORMATION
A. APPLICABILITY
NOTE: This modification is applicable by Service Bulletin only.
(1) Models
ON A/C 0005-0020
350-941
CONF ALL
(2) Applicability by MSN
0005-0020
(3) MSN by configuration
MSN CONFIGURATION
0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015
0016 0017 0018 0019 0020
001
(4) Configuration definition
Configuration 001
CONF 001 is applicable for all the aircraft affected by this Service Bulletin as a
standard configuration.
CONF 001 retrofits following modifications: 115148L91116.
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
This Service Bulletin is issued to answer to quality assurance department has
identified that a problem with internal interference of adjacent parts:
- Irregular welding of gimbal ring bush (raised and bumpy weld profile)
- Internal interference between bellows and gimbal rings (resistance between 7°
and 8.5°)
- Damage to the inside diameter of the bellows assy membrane 8.5° gimbal (dent
of outside of bellows).
(2) Objective/Action
This Service Bulletin consists in replacing a bleed air duct assembly containing
modified gimbal Standard (STD) on Right Hand (RH) wing.
(3) Advantages
The accomplishment of this Service Bulletin will improve the gimbal quality.

### Page 6

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 6
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
T o accomplish this Service Bulletin it is necessary to:
(1) Modification
(a) T ask set A350-A-36-XX-P022-01000-93AA-A Modification
1 Remove the Bleed Air Duct from the RH Wing to Pylon Interface
2 Install the Bleed Air Duct from the RH Wing to Pylon Interface
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin must be done before reaching 5600 Flight
Cycles (FC).
This Service Bulletin has been classified Mandatory. It is expected that an
Airworthiness Directive (AD) published by the European Aviation Safety Agency (EASA)
will be issued to confirm this classification. It is anticipated that the AD will confirm
the thresholds given but reference should be made to the AD for confirmation of the
mandated accomplishment timescale.
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) T ask set A350-A-36-XX-P022-01000-93AA-A Modification
PREPARATION
Job Set-up 2.00 h
PROCEDURE
Remove the Bleed Air Duct from the RH Wing to Pylon
Interface
1.00 h
Install the Bleed Air Duct from the RH Wing to Pylon
Interface
1.50 h
PREPARATION FOR TEST

### Page 7

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 7
Preparation for T est 0.25 h
TEST
Leak T est 1.00 h
CLOSE-UP
Close-up 2.00 h
TOTAL MAN-HOURS 7.75 h
ELAPSED TIME (HOURS) 5.25 h
H. WEIGHT AND BALANCE
Not changed
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
(1) Modification
(a) T ask set A350-A-36-XX-P022-01000-93AA-A Modification
AIRCRAFT STRUCTURAL REPAIR (ASR)
A350-A-51-77-11-00ZZZ-660Z-A
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
INTRODUCTION (INTRO)
A350-A-00-61-04-11ZZZ-018Z-D
MAINTENANCE PROCEDURE (MP)
A350-A-20-51-50-04ZZZ-25BZ-A A350-A-24-41-XX-00ZZZ-170Z-A
A350-A-36-11-48-00ZZZ-320Z-A
A350-A-36-11-48-07ZZZ-520Z-A
A350-A-36-11-48-08ZZZ-720Z-A
SYSTEM DESCRIPTION (SD)
A350-A-06-3X-XX-01ZZZ-04CZ-A A350-A-06-4X-XX-01ZZZ-04CZ-A
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
K. PUBLICATION AFFECTED
MAINTENANCE ILLUSTRATED PART DATA (MIPD)
MAINTENANCE PROCEDURE (MP)
L. INDUSTRY SUPPORT INFORMATION
AIRBUS will share the costs of accomplishment of this Service Bulletin by providing the kits
at no charge for orders placed before the Dec 31/21.
AIRBUS will credit the man-hours indicated in this Service Bulletin at the agreed in-house
warranty labor rate for claims received no later than 90 days after completion of the last

### Page 8

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 8
affected aircraft of your fleet, for the accomplishment of this Service Bulletin before the Dec
31/21.
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department: monitored.retrofit@airbus.com.

### Page 9

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 9
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
Material for task set A350-A-36-XX-P022-01000-93AA-A Modification
MATERIAL QTY SEE NOTES
Referenced tools See SB
Consumables See SB
Referenced consumables See SB
Part kit 36P022C01R01 1
Interchangeable parts See SB
Spare parts See SB
B. TOOLING
Referenced tools for task set A350-A-36-XX-P022-01000-93AA-A Modification
NOTE: T o accomplish this Service Bulletin it is necessary to use the tools listed in the
subsequent referenced tasks:
Ref. MP A350-A-36-11-48-07ZZZ-520Z-A
Ref. MP A350-A-36-11-48-08ZZZ-720Z-A
Ref. MP A350-A-36-11-48-00ZZZ-320Z-A
C. CONSUMABLES
Consumables for task set A350-A-36-XX-P022-01000-93AA-A Modification
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
Referenced consumables for task set A350-A-36-XX-P022-01000-93AA-A
Modification
NOTE: T o accomplish this Service Bulletin it is necessary to use the consumable materials
listed in the subsequent referenced tasks:
Ref. MP A350-A-20-51-50-04ZZZ-25BZ-A
Ref. MP A350-A-36-11-48-00ZZZ-320Z-A
D. LIST OF NEW PARTS
Part kit 36P022C01R01
Cost 44500.00 USD
Availability 120 d (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
airbus.kit@airbus.com.
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.

### Page 10

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 10
Procurement address D4296
AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
Phone: +49 40 743 51775
E-mail: airbus.kit@airbus.com
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
6 ABS1407-02N96 2 SEAL
7 V3616510600600 1 DUCT
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
E. LIST OF EXISTING PARTS
Interchangeable parts for task set A350-A-36-XX-P022-01000-93AA-A Modification
DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
DUCT ASSY V3616510600400 V3616510600600 01 (1) (2)
NOTE(S)
For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter
2).
(1): The interchangeability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.
(2): Mixability not applicable.
Spare parts for task set A350-A-36-XX-P022-01000-93AA-A Modification
DESCRIPTION OLD PART No. SEE NOTES
DUCT ASSY V3616510600400 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.

### Page 11

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 11
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A350-A-36-XX-P022-01000-93AA-A
Modification
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESP A350-A-20-55-
XX-01ZZZ-042Z-A.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including RC paragraph contained herein, contact
AIRBUS for further instructions and approval.
NOTE: Discarded parts must be managed at the operator's discretion.
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
TOTAL MAN-HOURS 7.75 h
ELAPSED TIME (HOURS) 5.25 h

### Page 12

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 12
B. PREPARATION
(1) Task A350-A-36-XX-P022-01001-540A-A - Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 2.00 h
Minimum Number of person 2
Elapsed Time 1.00 h
Referenced Information
Manuals/Drawings References/Sheets
INTRO A350-A-00-61-04-11ZZZ-018Z-D
MP A350-A-24-41-XX-00ZZZ-170Z-AA350-A-36-11-48-07ZZZ-520Z-A
Procedure
NOTE: For the basic Aircraft configuration, refer to Ref. INTRO A350-
A-00-61-04-11ZZZ-018Z-D "Maintenance Procedure - Introduction".
(a) Make sure that the aircraft is electrically grounded, refer to Ref. MP A350-
A-24-41-XX-00ZZZ-170Z-A.
(b) Do the job set-up procedure as specified in the removal of the wing bleed air
ducts between the inboard closing rib and the outboard closing rib, refer to Ref.
MP A350-A-36-11-48-07ZZZ-520Z-A.
NOTE: It is necessary to remove only Panel 622AT and Panel 465DR. It is not
necessary to remove Panel 622AB and Panel 623AB as specified in
the job set-up of the removal of the wing bleed air ducts between the
inboard closing rib and the outboard closing rib, refer to Ref. MP A350-
A-36-11-48-07ZZZ-520Z-A.
C. PROCEDURE
(1) Task A350-A-36-XX-P022-01001-520A-A - Remove the Bleed Air Duct from the
RH Wing to Pylon Interface
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
465 Access Panel 465DR
622 Access Panel 622AT
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h

### Page 13

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 13
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-77-11-00ZZZ-660Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-AA350-A-06-4X-XX-01ZZZ-04CZ-A
CML CONSUMABLE MATERIAL LIST (CML)
Procedure
(a) Standard practices given in this procedure:
1 For identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-04CZ-A.
2 For the identification of access panels, refer to Ref. SD A350-A-06-4X-
XX-01ZZZ-04CZ-A.
3 T ag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
5 For the specification of Material application codes given in this Service
Bulletin, refer to the Ref. CML.
6 Do the cleaning process in accordance with Ref. ASR A350-
A-51-77-11-00ZZZ-660Z-A.
(b) Remove the duct assy:
Refer to Ref. Fig. Removal of the Bleed Air Duct from the RH Wing to Pylon
Interface
1 Disconnect the hose assembly, Item (1), to remove the muff, Item (3).
2 Release the velcro tapes of the muffs, Item (2) and Item (3), to open these.
3 Remove the muffs, Item (2) and Item (3):
1 MUFFLER ASSY   Item (2) Retain
1 MUFF INSULATION   Item (3) Retain
4 Remove the self locking nut, Item (4), then open and remove the clamp,
Item (5):
1 SELF LOCKING NUT   Item (4) Retain
1 CLAMP   Item (5) Retain
5 Remove the self locking nut, Item (8), then open and remove the clamp,
Item (9):
1 SELF LOCKING NUT   Item (8) Retain
1 CLAMP   Item (9) Retain

### Page 14

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 14
6 Remove the duct, Item (7):
1 DUCT ASSY V3616510600400 Item (7) Discard
7 Remove the applicable E-seal, Item (6):
2 E-SEAL   Item (6) Discard
8 Put a blanking plug in each disconnected duct end.
9 Clean the work area and the retained parts with:
  Non Aqueous Cleaner -
General
08BAA9  
and
  T extile - Lint free Cotton14SBA1

### Page 15

A350
SERVICE BULLETIN
Figure ICN-A350-A-36XXP022-A-FAPE3-05CF7-A-001-01 SHEET 1/2
REV 00 Jan 17/20 A350-36-P022Removal of the Bleed Air Duct from
the RH Wing to Pylon Interface Page 15
CONF ALL
C
B
Z465Z622 A
A
FRONT SPAR
INBD CLOSING RIB
OUTBD CLOSING RIB
D
C
B
622AT
465DR
ICN-A350-A-36XXP022-A-FAPE3-05CF7-A-001-01

### Page 16

A350
SERVICE BULLETIN
Figure ICN-A350-A-36XXP022-A-FAPE3-05CFT-A-001-01 SHEET 2/2
REV 00 Jan 17/20 A350-36-P022Removal of the Bleed Air Duct from
the RH Wing to Pylon Interface Page 16
CONF ALL
D
E
E
(4)
(5)
(6)
(2)
(7)
(6)
(9)
(8)
(1)
(3)
ICN-A350-A-36XXP022-A-FAPE3-05CFT-A-001-01

### Page 17

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 17
(2) Task A350-A-36-XX-P022-01001-720A-A - Install the Bleed Air Duct from the
RH Wing to Pylon Interface
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
465 Access Panel 465DR
622 Access Panel 622AT
Manpower/Resources/Skills
Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50 h
Material necessary to do the job
Part kit 36P022C01R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
6 ABS1407-02N96 2 SEAL
7 V3616510600600 1 DUCT
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-20-51-50-04ZZZ-25BZ-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-AA350-A-06-4X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-04CZ-A.
2 For the identification of access panels, refer to Ref. SD A350-A-06-4X-
XX-01ZZZ-04CZ-A.
(b) Install the new duct assy:
Refer to Ref. Fig. Installation of the Bleed Air Duct from the RH Wing to Pylon
Interface
1 Remove the blanking plug from each disconnected duct end.
2 Put the duct, Item 7, in position between the pipe junction, Item (10), and
the pipe junction, Item (11):
1 DUCT ASSY V3616510600600 Item 7
3 Install the applicable E-seal, Item 6, at the end of the pipe junction, Item
(10):
1 E-SEAL ABS1407-02N96 Item 6
4 Engage the duct, Item 7, with the pipe junction, Item (10), and put the
clamp, Item (5), on the E-seal, Item 6:
1 DUCT ASSY V3616510600600 Item 7
1 CLAMP   Item (5) Retained

### Page 18

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 18
NOTE: Be careful to make sure that the E-seal, Item 6, at end of the duct,
Item 7, are correctly assembled.
NOTE: Be careful to make sure that there is a clearance between the E-
seal, Item 6, of the clamp, Item (5), and the sensing elements.
5 Install the applicable E-seal, Item 6, at the end of the pipe junction, Item
(11):
1 E-SEAL ABS1407-02N96 Item 6
6 Engage the duct, Item 7, with the pipe junction, Item (11), and put the
clamp, Item (9), on the E-seal, Item 6:
1 DUCT ASSY V3616510600600 Item 7
1 CLAMP   Item (9) Retained
NOTE: Be careful to make sure that the E-seal, Item 6, at end of the duct,
Item 7, are correctly assembled.
NOTE: Be careful to make sure that there is a clearance between the E-
seal, Item 6, of the clamp, Item (9), and the sensing elements.
7 Install the self locking nuts, Item (4) and Item (8), on the clamps, Item (5)
and Item (9):
1 SELF LOCKING NUT   Item (4) Retained
1 SELF LOCKING NUT   Item (8) Retained
8 T orque the self locking nuts, Item (4) and Item (8), to between 3.39 and
3.95 Nm (30.004 and 34.960 lbf.in.).
9 Put a mark on the self locking nuts, Item (4) and Item (8), refer to Ref. MP
A350-A-20-51-50-04ZZZ-25BZ-A.
10 Install the muffs, Item (2) and Item (3):
1 MUFFLER ASSY   Item (2) Retained
1 MUFF INSULATION   Item (3) Retained
NOTE: The correct position of the muffler assy and muff insulation for
installation is specified by the shape of the muff.
NOTE: Be careful to make sure to respect the minimum distance from the
elements of structure at 20 mm (0.787 in.).
11 Connect the hose assembly, Item (1).
12 T orque the hose assembly connection, Item (1), to between 24.30 and
31.60 Nm (215.073 and 279.684 lbf.in.).
13 Put a mark on the hose assembly connection, Item (1), refer to Ref. MP
A350-A-20-51-50-04ZZZ-25BZ-A.

### Page 19

A350
SERVICE BULLETIN
Figure ICN-A350-A-36XXP022-A-FAPE3-05BQ2-A-001-01 SHEET 1/3
REV 00 Jan 17/20 A350-36-P022Installation of the Bleed Air Duct
from the RH Wing to Pylon Interface Page 19
CONF ALL
C
B
Z465Z622 A
A
FRONT SPAR
INBD CLOSING RIB
OUTBD CLOSING RIB
D
C
B
622AT
465DR
F
ICN-A350-A-36XXP022-A-FAPE3-05BQ2-A-001-01

### Page 20

A350
SERVICE BULLETIN
Figure ICN-A350-A-36XXP022-A-FAPE3-05BQ3-A-002-01 SHEET 2/3
REV 00 Jan 17/20 A350-36-P022Installation of the Bleed Air Duct
from the RH Wing to Pylon Interface Page 20
CONF ALL
(30.004 AND 34.960 lbf.in).
TORQUE THE HOSE ASSEMBLY CONNECTION, ITEM (1), TO BETWEEN 24.30 AND 31.60 Nm02
(215.073 AND 279.684 lbf.in).
NOTE:
TORQUE THE SELF LOCKING NUTS, ITEM (4) AND ITEM (8), TO BETWEEN 3.39 AND 3.95 Nm 01
E
D
(4)
(5)
6
(2)
7
6
(9)
(8)
(1)
(3)
E
(10)
(11)
01
01
02
ICN-A350-A-36XXP022-A-FAPE3-05BQ3-A-002-01

### Page 21

A350
SERVICE BULLETIN
Figure ICN-A350-A-36XXP022-A-FAPE3-05BQ4-A-001-01 SHEET 3/3
REV 00 Jan 17/20 A350-36-P022Installation of the Bleed Air Duct
from the RH Wing to Pylon Interface Page 21
CONF ALL
VIEW LOOKING DOWN
FWD
INBD CLOSING RIB
OUTBD CLOSING RIB
A
A
A A
NOTE:
MINIMUM DISTANCE FROM THE ELEMENTS: 20 mm (0.787 in).03
03
F
ICN-A350-A-36XXP022-A-FAPE3-05BQ4-A-001-01

### Page 22

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 22
D. PREPARATION FOR TEST
(1) Task A350-A-36-XX-P022-01001-92AA-A - Preparation for Test
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-36-11-48-08ZZZ-720Z-A
Procedure
(a) Remove the safety clip(s) and/or tag(s) and close/unlock the circuit breaker(s),
refer to Ref. MP A350-A-36-11-48-08ZZZ-720Z-A.
E. TEST
(1) Task A350-A-36-XX-P022-01001-364A-A - Leak Test
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 2
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-36-11-48-00ZZZ-320Z-A
Procedure
(a) Do the leak test of the bleed air ducting in the wing area between bleed air
precooler exchangers, wing anti-ice valves and wing/fuselage connection, refer
to Ref. MP A350-A-36-11-48-00ZZZ-320Z-A.
F. CLOSE-UP
(1) Task A350-A-36-XX-P022-01001-740A-A - Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 2.00 h
Minimum Number of person 2
Elapsed Time 1.00 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-36-11-48-08ZZZ-720Z-A
Procedure

### Page 23

A350
SERVICE BULLETIN
REV 00 Jan 17/20 A350-36-P022
Page 23
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Do the close-up procedure as specified in the installation of the wing bleed air
ducts between the inboard closing rib and the outboard closing rib, refer to Ref.
MP A350-A-36-11-48-08ZZZ-720Z-A.
NOTE: It is necessary to install only Panel 622AT and Panel 465DR.
(c) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A350-A-36-XX-P022-01001-90AA-A - Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 24

A350
SERVICE BULLETIN
APPENDIX
REV 00 Jan 17/20 A350-36-P022
Page 24
APPENDIX
A. REPORTING SHEET
TITLE: PNEUMATIC - DISTRIBUTION - INSTALL NEW BLEED DUCT WELDED
ASSEMBLY COMPRISING NEW GIMBAL STANDARD REFERENCE - RHS
MODIFICATION No.: 115148L91116
(1) SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance
and Flight Operations Products if it is duly reported to Airbus.
(2) GENERAL information
The SB Reporting policy is published in ISI 00.00.00135. This document provides
information regarding: the SB Reporting means and benefits, the update of
customized Maintenance Products and customized Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations
Products" for further information on the update of affected Flight Operations Products.
(3) SB Reporting procedure
Standard practice to report SB is to use the online reporting application on
AirbusWorld.
Refer to ISI 00.00.00179:
- For complete information on reporting means to Airbus, Question 2 "What are
the standard practices for SB Reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs,
Question 3 "What about the reporting of prerequisite Service Bulletins?"
NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.

### Page 25

A350
SERVICE BULLETIN
APPENDIX
REV 00 Jan 17/20 A350-36-P022
Page 25
B. QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin.
The reported data that you provide us will be used to analyse areas of difficulties and to
take corrective action to further improve the quality of our Service Bulletin.
We thank you for the time you have taken in completing this form.
Quality rating of this SB 4 3 2 1
Quality rating of the Accomplishment Instructions 4 3 2 1
Quality rating of the Illustrations 4 3 2 1
Is this SB easy to understand ? Y / N
NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score
If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.
Planning Material Instructions
X Applicability X T ooling X Preparation
X Reason X List of Materials
Operator Supplied
X Mod/Inspection
X Manpower X Kit content X T est
X References X Re-identification X Close-up
X Publication X Illustrations
X Industry Support
Comments :
Operator : Date :
Name/Title
Please return this form to :
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
Or via your Resident Customer Support Office.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
