# Airbus Service Bulletin A350-36-P023

Copy: No revision named ("SB A350-36-P023"), 25 pages: PDF https://openairdocs.org/files/sha256/76/a4/76a4b3301b32dbca79c88285debd9a889c4da84f8e30d4a1e227844abd6b6531; text https://openairdocs.org/service-documents/airbus/a350-36-p023/file/76a4b3301b32.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2020-0965, the docket of AD 2021-08-08. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A350-36-P023
- Page: https://openairdocs.org/service-documents/airbus/a350-36-p023

## Text (25 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2020-0965, the docket of AD 2021-08-08. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 1
CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
 
The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.
ATA SYSTEM: 36
TITLE: PNEUMATIC - DISTRIBUTION - INSTALL NEW BLEED GIMBAL
STANDARD REFERENCE - LHS
MODIFICATION No.:
114810L91112

### Page 2

A350
SERVICE BULLETIN
SUMMARY
REV 00 Apr 09/20 A350-36-P023
Page 2
ATA SYSTEM: 36
TITLE: PNEUMATIC - DISTRIBUTION - INSTALL NEW BLEED GIMBAL
STANDARD REFERENCE - LHS
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR None
MINOR 114810L91112
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
B. REASON
(1) History
This Service Bulletin is issued to answer to quality assurance department has
identified that a problem with internal interference of adjacent parts:
- Irregular welding of gimbal ring bush (raised and bumpy weld profile)
- Internal interference between bellows and gimbal rings (resistance between 7°
and 8.5°)
- Damage to the inside diameter of the bellows assy membrane 8.5° gimbal (dent
of outside of bellows).
(2) Objective/Action
This Service Bulletin consists in replacing a bleed gimbal Standard (STD) on Left Hand
(LH) wing.
(3) Advantages
Accomplishment of this Service Bulletin cancels the requirements of Ref. SB A350-36-
P029.
The accomplishment of this Service Bulletin will improve the gimbal quality.
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE RECOMMENDED COST SAVING NO
A/C OPERATION
AFFECTED
NO VENDOR SB NO
CANCELS INSPECTION SB YES ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD YES
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO

### Page 3

A350
SERVICE BULLETIN
SUMMARY
REV 00 Apr 09/20 A350-36-P023
Page 3
NOTE: Service Bulletin recommended to be accomplished to prevent significant
operational disruptions.
D. MAINTENANCE CONFIGURATION
No specific aircraft maintenance configuration required.
E. MATERIAL PRICE INFORMATION
(1) Modification
(a) T ask set A350-A-36-XX-P023-01000-93AA-A Modification
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Part kit 36P023C01R01 1 4300.00 USD Gimbal joint, E-seal
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
82W AAR AFR BAW CAL CCA CES CHH CPA CSC CSN DAL DLH ETD ETH EVE FBU FIN FJI FWI
HVN IBE JAL MAS MAU PAL QTR SAA SIA TAM THA VIR
G. CONCURRENT REQUIREMENTS
None
H. NATURE OF THE WORK
(1) Modification
(a) T ask set A350-A-36-XX-P023-01000-93AA-A Modification
AIRCRAFT YES
EQUIPMENT NO
I. MANPOWER
(1) Modification
(a) T ask set A350-A-36-XX-P023-01000-93AA-A Modification
MANPOWER
TOTAL MAN-HOURS 7.75 h
ELAPSED TIME (HOURS) 5.25 h

### Page 4

A350
SERVICE BULLETIN
SUMMARY
Figure ICN-A350-A-36XXP023-A-FAPE3-05C0C-A-001-01 SHEET 1/1
REV 00 Apr 09/20 A350-36-P023General overview
Page 4
J. GENERAL OVERVIEW
CONF ALL
B
C
B
Z455 Z522A
C
A
522AT
455DL
FRONT SPAR
INBD CLOSING RIB
OUTBD CLOSING RIB
REPLACEMENT OF THE 
BLEED GIMBAL
STANDARD REFERENCE
ICN-A350-A-36XXP023-A-FAPE3-05C0C-A-001-01

### Page 5

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 5
ATA SYSTEM: 36
TITLE: PNEUMATIC - DISTRIBUTION - INSTALL NEW BLEED GIMBAL
STANDARD REFERENCE - LHS
1. PLANNING INFORMATION
A. APPLICABILITY
NOTE: This modification is applicable by Service Bulletin only.
(1) Models
ON A/C 0088, 0102, 0110, 0118, 0125, 0141, 0161, 0169, 0188, 0206, 0215, 0225, 0229,
0233, 0241, 0252, 0258, 0262, 0266, 0274, 0286, 0290, 0296, 0298, 0306, 0315, 0319,
0326, 0330, 0332, 0336, 0340, 0342
350-1041
ON A/C 0021-0058, 0060-0064, 0066-0070, 0072-0087, 0089-0101, 0103-0107, 0109, 0111-
0117, 0119-0124, 0126-0130, 0132-0138, 0140, 0142-0151, 0153-0155, 0157-0160, 0162-
0165, 0167, 0168, 0170, 0172-0187, 0189-0193, 0195-0205, 0207-0214, 0216-0221, 0223,
0224, 0226-0228, 0230-0232, 0234-0240, 0243-0251, 0254-0257, 0259-0261, 0263-0265,
0267-0273, 0276-0285, 0287, 0289, 0291-0295, 0297, 0299-0303, 0305, 0307-0314, 0316,
0318, 0320-0325, 0327-0329, 0331, 0333-0335, 0337-0339, 0341, 0343, 0347, 0351
350-941
CONF ALL
(2) Applicability by MSN
0021-0058 0060-0064 0066-0070 0072-0107 0109-0130 0132-0138 0140-0151 0153-
0155 0157-0165 0167-0170 0172-0193 0195-0221 0223-0241 0243-0252 0254-0274
0276-0287 0289-0303 0305-0316 0318-0343 0347 0351
(3) MSN by configuration
MSN CONFIGURATION
0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031
0032 0033 0034 0035 0036 0037 0038 0039 0040 0041 0042
0043 0044 0045 0046 0047 0048 0049 0050 0051 0052 0053
0054 0055 0056 0057 0058 0060 0061 0062 0063 0064 0066
0067 0068 0069 0070 0072 0073 0074 0075 0076 0077 0078
0079 0080 0081 0082 0083 0084 0085 0086 0087 0088 0089
0090 0091 0092 0093 0094 0095 0096 0097 0098 0099 0100
0101 0102 0103 0104 0105 0106 0107 0109 0110 0111 0112
0113 0114 0115 0116 0117 0118 0119 0120 0121 0122 0123
0124 0125 0126 0127 0128 0129 0130 0132 0133 0134 0135
0136 0137 0138 0140 0141 0142 0143 0144 0145 0146 0147
0148 0149 0150 0151 0153 0154 0155 0157 0158 0159 0160
0161 0162 0163 0164 0165 0167 0168 0169 0170 0172 0173
0174 0175 0176 0177 0178 0179 0180 0181 0182 0183 0184
0185 0186 0187 0188 0189 0190 0191 0192 0193 0195 0196
0197 0198 0199 0200 0201 0202 0203 0204 0205 0206 0207
0208 0209 0210 0211 0212 0213 0214 0215 0216 0217 0218
0219 0220 0221 0223 0224 0225 0226 0227 0228 0229 0230
0231 0232 0233 0234 0235 0236 0237 0238 0239 0240 0241
0243 0244 0245 0246 0247 0248 0249 0250 0251 0252 0254
0255 0256 0257 0258 0259 0260 0261 0262 0263 0264 0265
0266 0267 0268 0269 0270 0271 0272 0273 0274 0276 0277
0278 0279 0280 0281 0282 0283 0284 0285 0286 0287 0289
001

### Page 6

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 6
MSN CONFIGURATION
0290 0291 0292 0293 0294 0295 0296 0297 0298 0299 0300
0301 0302 0303 0305 0306 0307 0308 0309 0310 0311 0312
0313 0314 0315 0316 0318 0319 0320 0321 0322 0323 0324
0325 0326 0327 0328 0329 0330 0331 0332 0333 0334 0335
0336 0337 0338 0339 0340 0341 0342 0343 0347 0351
(4) Configuration definition
Configuration 001
CONF 001 is applicable for all the aircraft affected by this Service Bulletin as a
standard configuration.
CONF 001 retrofits following modifications: 114810L91112.
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
This Service Bulletin is issued to answer to quality assurance department has
identified that a problem with internal interference of adjacent parts:
- Irregular welding of gimbal ring bush (raised and bumpy weld profile)
- Internal interference between bellows and gimbal rings (resistance between 7°
and 8.5°)
- Damage to the inside diameter of the bellows assy membrane 8.5° gimbal (dent
of outside of bellows).
(2) Objective/Action
This Service Bulletin consists in replacing a bleed gimbal Standard (STD) on Left Hand
(LH) wing.
(3) Advantages
Accomplishment of this Service Bulletin cancels the requirements of Ref. SB A350-36-
P029.
The accomplishment of this Service Bulletin will improve the gimbal quality.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
T o accomplish this Service Bulletin it is necessary to:
(1) Modification
(a) T ask set A350-A-36-XX-P023-01000-93AA-A Modification
1 Remove the Bleed Gimbal Standard Reference for the LH Wing to Pylon
Interface
2 Install the Bleed Gimbal Standard Reference for the LH Wing to Pylon
Interface
E. COMPLIANCE

### Page 7

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 7
(1) Classification
RECOMMENDED: Service Bulletin recommended to be accomplished to prevent
significant operational disruptions.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin is recommended before reaching 5600 Flight
Cycles (FC).
This Service Bulletin has been classified Recommended. It is expected that an
Airworthiness Directive (AD) published by the European Aviation Safety Agency (EASA)
will be issued to change this classification to Mandatory. It is anticipated that the
AD will confirm the thresholds given but reference should be made to the AD for
confirmation of the mandated accomplishment timescale.
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) T ask set A350-A-36-XX-P023-01000-93AA-A Modification
PREPARATION
Job Set-up 2.00 h
PROCEDURE
Remove the Bleed Gimbal Standard Reference for the LH
Wing to Pylon Interface
1.00 h
Install the Bleed Gimbal Standard Reference for the LH
Wing to Pylon Interface
1.50 h
PREPARATION FOR TEST
Preparation for T est 0.25 h
TEST
Leak T est 1.00 h
CLOSE-UP
Close-up 2.00 h
TOTAL MAN-HOURS 7.75 h
ELAPSED TIME (HOURS) 5.25 h
H. WEIGHT AND BALANCE
Not changed

### Page 8

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 8
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
(1) Modification
(a) T ask set A350-A-36-XX-P023-01000-93AA-A Modification
AIRCRAFT STRUCTURAL REPAIR (ASR)
A350-A-51-77-11-00ZZZ-660Z-A
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
INTRODUCTION (INTRO)
A350-A-00-61-04-11ZZZ-018Z-D
MAINTENANCE PROCEDURE (MP)
A350-A-20-51-50-04ZZZ-25BZ-A A350-A-24-41-XX-00ZZZ-170Z-A
A350-A-36-11-48-00ZZZ-320Z-A
A350-A-36-11-48-07ZZZ-520Z-A
A350-A-36-11-48-08ZZZ-720Z-A
SERVICE BULLETIN (SB)
A350-36-P029
SYSTEM DESCRIPTION (SD)
A350-A-06-3X-XX-01ZZZ-04CZ-A A350-A-06-4X-XX-01ZZZ-04CZ-A
TECHNICAL FOLLOW UP (TFU)
36.11.00107
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
K. PUBLICATION AFFECTED
MAINTENANCE ILLUSTRATED PART DATA (MIPD)
MAINTENANCE PROCEDURE (MP)
L. INDUSTRY SUPPORT INFORMATION
For aircraft on which this SB is accomplished further to finding as per inspection Ref. SB
A350-36-P029:
- AIRBUS will share the costs of accomplishment of this Service Bulletin by providing the
kits at no charge for orders placed within 24 months after the initial issue date of the
Service Bulletin.
- AIRBUS will credit the man hours indicated in this Service Bulletin at the agreed in-
house warranty labor rate for the accomplishment of this Service Bulletin within 24
months after the initial issue date of the inspection Service Bulletin. Claims shall be
received no later than 90 days after the last aircraft of your fleet completed within 24
months after the initial issue date of the inspection Service Bulletin.

### Page 9

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 9
- This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
- For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department: monitored.retrofit@airbus.com.
For aircraft on which this SB is not accomplished further to finding as per inspection Ref. SB
A350-36-P029:
- AIRBUS will not provide industry support for accomplishment of this Service Bulletin.
- This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
- For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department: monitored.retrofit@airbus.com.

### Page 10

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 10
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
Material for task set A350-A-36-XX-P023-01000-93AA-A Modification
MATERIAL QTY SEE NOTES
Referenced tools See SB
Consumables See SB
Referenced consumables See SB
Part kit 36P023C01R01 1
Interchangeable parts See SB
Spare parts See SB
B. TOOLING
Referenced tools for task set A350-A-36-XX-P023-01000-93AA-A Modification
T o accomplish this Service Bulletin it is necessary to use the tools listed in the subsequent
referenced tasks:
Ref. MP A350-A-36-11-48-07ZZZ-520Z-A
Ref. MP A350-A-36-11-48-08ZZZ-720Z-A
Ref. MP A350-A-36-11-48-00ZZZ-320Z-A
C. CONSUMABLES
Consumables for task set A350-A-36-XX-P023-01000-93AA-A Modification
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
Referenced consumables for task set A350-A-36-XX-P023-01000-93AA-A
Modification
T o accomplish this Service Bulletin it is necessary to use the consumable materials listed in
the subsequent referenced tasks:
Ref. MP A350-A-20-51-50-04ZZZ-25BZ-A
Ref. MP A350-A-36-11-48-00ZZZ-320Z-A
D. LIST OF NEW PARTS
Part kit 36P023C01R01
Cost 4300.00 USD
Availability 200 d (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
airbus.kit@airbus.com.
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.

### Page 11

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 11
Procurement address D4296
AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
Phone: +49 40 743 51775
E-mail: airbus.kit@airbus.com
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
5 ABS0736E9696R 1 JOINT
6 ABS1407-02N96 2 SEAL
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
E. LIST OF EXISTING PARTS
Interchangeable parts for task set A350-A-36-XX-P023-01000-93AA-A Modification
DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
JOINT-GIMBAL ABS0736E9696S ABS0736E9696R 01 (1) (2)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter
2).
(1): The interchangeability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.
(2): Mixability not applicable.
Spare parts for task set A350-A-36-XX-P023-01000-93AA-A Modification
DESCRIPTION OLD PART No. SEE NOTES
JOINT-GIMBAL ABS0736E9696S (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.

### Page 12

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 12
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A350-A-36-XX-P023-01000-93AA-A
Modification
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESP A350-A-20-55-XX-01ZZZ-
042Z-A.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including RC paragraph contained herein, contact
AIRBUS for further instructions and approval.
NOTE: Discarded parts must be managed at the operator's discretion.
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
TOTAL MAN-HOURS 7.75 h
ELAPSED TIME (HOURS) 5.25 h

### Page 13

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 13
B. PREPARATION
(1) Task A350-A-36-XX-P023-01001-540A-A - Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 2.00 h
Minimum Number of person 2
Elapsed Time 1.00 h
Referenced Information
Manuals/Drawings References/Sheets
INTRO A350-A-00-61-04-11ZZZ-018Z-D
MP A350-A-24-41-XX-00ZZZ-170Z-AA350-A-36-11-48-07ZZZ-520Z-A
Procedure
NOTE: For the basic Aircraft configuration, refer to Ref. INTRO A350-A-00-61-04-
11ZZZ-018Z-D "Maintenance Procedure - Introduction".
(a) Make sure that the aircraft is electrically grounded, refer to Ref. MP A350-A-24-
41-XX-00ZZZ-170Z-A.
(b) Do the job set-up procedure as specified in the removal of the wing bleed air
ducts between the inboard closing rib and the outboard closing rib, refer to Ref.
MP A350-A-36-11-48-07ZZZ-520Z-A.
NOTE: It is necessary to remove only Panel 522AT and Panel 455DL.
C. PROCEDURE
(1) Task A350-A-36-XX-P023-01001-520A-A - Remove the Bleed Gimbal Standard
Reference for the LH Wing to Pylon Interface
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
455 Access Panel 455DL
522 Access Panel 522AT
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton

### Page 14

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 14
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-77-11-00ZZZ-660Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-AA350-A-06-4X-XX-01ZZZ-04CZ-A
CML CONSUMABLE MATERIAL LIST (CML)
Procedure
(a) Standard practices given in this procedure:
1 For identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-04CZ-A.
2 For the identification of access panels, refer to Ref. SD A350-A-06-4X-XX-
01ZZZ-04CZ-A.
3 T ag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
5 For the specification of Material application codes given in this Service
Bulletin, refer to the Ref. CML.
6 Do the cleaning process in accordance with Ref. ASR A350-A-51-77-11-
00ZZZ-660Z-A.
(b) Remove the bleed gimbal:
Refer to Ref. Fig. Removal of the Bleed Gimbal Standard Reference for the LH
Wing to Pylon Interface
1 Disconnect the hose assembly, Item (1), to remove the muff, Item (2).
2 Release the velcro tapes of the muffs, Item (2), to open this.
3 Remove and retain the muff, Item (2):
1 MUFF INSULATION   Item (2) Retain
4 Remove the self locking nut, Item (3), then open and remove the clamp,
Item (4):
2 SELF LOCKING NUT   Item (3) Retain
2 CLAMP   Item (4) Retain
5 Remove the gimbal, Item (5):
1 JOINT-GIMBAL ABS0736E9696S Item (5) Discard
6 Remove the applicable E-seal, Item (6):
2 E-SEAL   Item (6) Discard
7 Put a blanking plug in each disconnected duct end.
8 Clean the work area and the retained parts with:
  Non Aqueous Cleaner -
General
08BAA9  
and
  T extile - Lint free Cotton14SBA1

### Page 15

A350
SERVICE BULLETIN
Figure ICN-A350-A-36XXP023-A-FAPE3-05C0D-A-001-01 SHEET 1/2
REV 00 Apr 09/20 A350-36-P023Removal of the Bleed Gimbal Standard
Reference for the LH Wing to Pylon Interface Page 15
CONF ALL
B
C
B
Z455 Z522A
C
A
522AT
455DL
FRONT SPAR
INBD CLOSING RIB
OUTBD CLOSING RIB
D
ICN-A350-A-36XXP023-A-FAPE3-05C0D-A-001-01

### Page 16

A350
SERVICE BULLETIN
Figure ICN-A350-A-36XXP023-A-FAPE3-05C0Q-A-001-01 SHEET 2/2
REV 00 Apr 09/20 A350-36-P023Removal of the Bleed Gimbal Standard
Reference for the LH Wing to Pylon Interface Page 16
CONF ALL
D
(3)
(4)
(6)
(2)
(1)
(3)
(4)
(6)
(5)
ICN-A350-A-36XXP023-A-FAPE3-05C0Q-A-001-01

### Page 17

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 17
(2) Task A350-A-36-XX-P023-01001-720A-A - Install the Bleed Gimbal Standard
Reference for the LH Wing to Pylon Interface
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
455 Access Panel 455DL
522 Access Panel 522AT
Manpower/Resources/Skills
Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50 h
Material necessary to do the job
Part kit 36P023C01R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
5 ABS0736E9696R 1 JOINT
6 ABS1407-02N96 2 SEAL
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-20-51-50-04ZZZ-25BZ-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-AA350-A-06-4X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-04CZ-A.
2 For the identification of access panels, refer to Ref. SD A350-A-06-4X-XX-
01ZZZ-04CZ-A.
(b) Install the new bleed gimbal:
Refer to Ref. Fig. Installation of the Bleed Gimbal Standard Reference for the LH
Wing to Pylon Interface
1 Remove the blanking plug from each disconnected duct end.
2 Put the gimbal, Item 5, in position between the pipe junction, Item (7), and
the pipe junction, Item (8):
1 JOINT-GIMBAL ABS0736E9696R Item 5
3 Install the applicable E-seal, Item 6, at the end of the pipe junction, Item
(7):
1 E-SEAL ABS1407-02N96 Item 6
4 Engage the gimbal, Item 5, with the pipe junction, Item (7), and put the
clamp, Item (4), on the E-seal, Item 6:
1 JOINT-GIMBAL ABS0736E9696R Item 5
1 CLAMP   Item (4) Retained

### Page 18

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 18
NOTE: Be careful to make sure that the E-seal, Item 6, at end of the pipe
junction, Item (7), are correctly assembled.
NOTE: Be careful to make sure that there is a clearance between the E-
seal, Item 6, of the clamp, Item (4), and the sensing elements.
5 Install the applicable E-seal, Item 6, at the end of the pipe junction, Item
(8):
1 E-SEAL ABS1407-02N96 Item 6
6 Engage the gimbal, Item 5, with the pipe junction, Item (8), and put the
clamp, Item (4), on the E-seal, Item 6:
1 JOINT-GIMBAL ABS0736E9696R Item 5
1 CLAMP   Item (4) Retained
NOTE: Be careful to make sure that the E-seal, Item 6, at end of the pipe
junction, Item (8), are correctly assembled.
NOTE: Be careful to make sure that there is a clearance between the E-
seal, Item 6, of the clamp, Item (4), and the sensing elements.
7 Install the self locking nuts, Item (3), on the clamps, Item (4):
2 SELF LOCKING NUTS   Item (3) Retained
8 T orque the self locking nuts, Item (3), to between 3.39 and 3.95 Nm
(30.004 and 34.960 lbf.in.).
9 Put mark on the self locking nuts, Item (3), refer to Ref. MP A350-A-20-51-
50-04ZZZ-25BZ-A.
10 Install the retained muff, Item (2):
1 MUFF INSULATION   Item (2) Retained
NOTE: The correct position of the muffler assy and muff insulation for
installation is specified by the shape of the muff.
NOTE: Be careful to make sure to respect the minimum distance from the
elements of structure at 20 mm (0.787 in.).
NOTE: Be careful to make sure to respect the minimum distance from
environment at 5 mm (0.197 in.).
11 Connect the hose assembly, Item (1).
12 T orque the hose assembly connection, Item (1), to between 24.30 and
31.60 Nm (215.073 and 279.684 lbf.in.).
13 Put mark on the hose assembly connection, Item (1), refer to Ref. MP A350-
A-20-51-50-04ZZZ-25BZ-A.

### Page 19

A350
SERVICE BULLETIN
Figure ICN-A350-A-36XXP023-A-FAPE3-05BQ5-A-001-01 SHEET 1/3
REV 00 Apr 09/20 A350-36-P023Installation of the Bleed Gimbal Standard
Reference for the LH Wing to Pylon Interface Page 19
CONF ALL
B
C
B
Z455 Z522A
C
A
522AT
455DL
FRONT SPAR
INBD CLOSING RIB
OUTBD CLOSING RIB
D
E
ICN-A350-A-36XXP023-A-FAPE3-05BQ5-A-001-01

### Page 20

A350
SERVICE BULLETIN
Figure ICN-A350-A-36XXP023-A-FAPE3-05BQ6-A-002-01 SHEET 2/3
REV 00 Apr 09/20 A350-36-P023Installation of the Bleed Gimbal Standard
Reference for the LH Wing to Pylon Interface Page 20
CONF ALL
D
(3)
(4)
6
(2)
(1)
(3)
(4)
6
5
(8)
NOTE:
TORQUE THE SELF LOCKING NUTS, ITEM (3), TO BETWEEN 3.39 AND 3.95 Nm (30.004 AND 34.960 lbf.in).01
TORQUE THE HOSE ASSEMBLY CONNECTION, ITEM (1), TO BETWEEN 24.30 AND 31.60 Nm02
(215.073 AND 279.684 lbf.in).
02
01
01
(7)
ICN-A350-A-36XXP023-A-FAPE3-05BQ6-A-002-01

### Page 21

A350
SERVICE BULLETIN
Figure ICN-A350-A-36XXP023-A-FAPE3-05BQ7-A-001-01 SHEET 3/3
REV 00 Apr 09/20 A350-36-P023Installation of the Bleed Gimbal Standard
Reference for the LH Wing to Pylon Interface Page 21
CONF ALL
VIEW LOOKING DOWN
FWD
INBD CLOSING RIB
OUTBD CLOSING RIB
A
A
B
B
E
A A
B BNOTE:
MINIMUM DISTANCE FROM THE ELEMENTS: 20 mm (0.787 in).03
MINIMUM DISTANCE FROM THE WING ENVIRONMENT: 5 mm (0.197 in).04
03
04
ICN-A350-A-36XXP023-A-FAPE3-05BQ7-A-001-01

### Page 22

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 22
D. PREPARATION FOR TEST
(1) Task A350-A-36-XX-P023-01001-92AA-A - Preparation for Test
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-36-11-48-08ZZZ-720Z-A
Procedure
(a) Remove the safety clip(s) and/or tag(s) and close/unlock the circuit breaker(s),
refer to Ref. MP A350-A-36-11-48-08ZZZ-720Z-A.
E. TEST
(1) Task A350-A-36-XX-P023-01001-364A-A - Leak Test
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 2
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-36-11-48-00ZZZ-320Z-A
Procedure
(a) Do the leak test of the bleed air ducting in the wing area between bleed air
precooler exchangers, wing anti-ice valves and wing/fuselage connection, refer
to Ref. MP A350-A-36-11-48-00ZZZ-320Z-A.
F. CLOSE-UP
(1) Task A350-A-36-XX-P023-01001-740A-A - Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 2.00 h
Minimum Number of person 2
Elapsed Time 1.00 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-36-11-48-08ZZZ-720Z-A
Procedure

### Page 23

A350
SERVICE BULLETIN
REV 00 Apr 09/20 A350-36-P023
Page 23
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Do the close-up procedure as specified in the installation of the wing bleed air
ducts between the inboard closing rib and the outboard closing rib, refer to Ref.
MP A350-A-36-11-48-08ZZZ-720Z-A.
NOTE: It is necessary to install only Panel 522AT and Panel 455DL.
(c) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A350-A-36-XX-P023-01001-90AA-A - Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 24

A350
SERVICE BULLETIN
APPENDIX
REV 00 Apr 09/20 A350-36-P023
Page 24
APPENDIX
A. REPORTING SHEET
TITLE: PNEUMATIC - DISTRIBUTION - INSTALL NEW BLEED GIMBAL
STANDARD REFERENCE - LHS
MODIFICATION No.: 114810L91112
(1) SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance
and Flight Operations Products if it is duly reported to Airbus.
(2) GENERAL information
The SB Reporting policy is published in ISI 00.00.00135. This document provides
information regarding: the SB Reporting means and benefits, the update of
customized Maintenance Products and customized Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations
Products" for further information on the update of affected Flight Operations Products.
(3) SB Reporting procedure
Standard practice to report SB is to use the online reporting application on
AirbusWorld.
Refer to ISI 00.00.00179:
- For complete information on reporting means to Airbus, Question 2 "What are
the standard practices for SB Reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs,
Question 3 "What about the reporting of prerequisite Service Bulletins?"
NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.

### Page 25

A350
SERVICE BULLETIN
APPENDIX
REV 00 Apr 09/20 A350-36-P023
Page 25
B. QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin.
The reported data that you provide us will be used to analyse areas of difficulties and to
take corrective action to further improve the quality of our Service Bulletin.
We thank you for the time you have taken in completing this form.
Quality rating of this SB 4 3 2 1
Quality rating of the Accomplishment Instructions 4 3 2 1
Quality rating of the Illustrations 4 3 2 1
Is this SB easy to understand ? Y / N
NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score
If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.
Planning Material Instructions
X Applicability X T ooling X Preparation
X Reason X List of Materials
Operator Supplied
X Mod/Inspection
X Manpower X Kit content X T est
X References X Re-identification X Close-up
X Publication X Illustrations
X Industry Support
Comments :
Operator : Date :
Name/Title
Please return this form to :
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
Or via your Resident Customer Support Office.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
