# Airbus Service Bulletin A350-53-P057

Copy: No revision named ("A350-53-P057 R00"), 50 pages: PDF https://openairdocs.org/files/sha256/cc/6e/cc6e71d66cee4d0a77e85bcac2eedff2d4b2d8760bc763c5bc3d86b723322d7a; text https://openairdocs.org/service-documents/airbus/a350-53-p057/file/cc6e71d66cee.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2020-0681, the docket of AD 2020-26-21. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A350-53-P057
- Page: https://openairdocs.org/service-documents/airbus/a350-53-p057

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2020-26-21](https://openairdocs.org/ad/2020-26-21.md), effective Feb 3, 2021: No revision named

## Text (50 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2020-0681, the docket of AD 2020-26-21. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 1
CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
 
The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.
MANDATORY MANDATORY MANDATORY
ATA SYSTEM: 53
TITLE: FUSELAGE - CONE/REAR FUSELAGE - INSTALL SELF-ALIGNING NUTS
AT FRAME 98 FEET BETWEEN STRINGER 15/17 (LH/RH)
MODIFICATION No.:
115286L83020

### Page 2

A350
SERVICE BULLETIN
SUMMARY
REV 00 Feb 21/20 A350-53-P057
Page 2
ATA SYSTEM: 53
TITLE: FUSELAGE - CONE/REAR FUSELAGE - INSTALL SELF-ALIGNING NUTS
AT FRAME 98 FEET BETWEEN STRINGER 15/17 (LH/RH)
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
CONF 001
MODIFICATION CLASSIFICATION
MAJOR None
MINOR 115286L83020
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.
CONF 002
MODIFICATION CLASSIFICATION
MAJOR None
MINOR 115286L83020
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.
CONF 003
MODIFICATION CLASSIFICATION
MAJOR None
MINOR 115286L83020
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.

### Page 3

A350
SERVICE BULLETIN
SUMMARY
REV 00 Feb 21/20 A350-53-P057
Page 3
CONF ALL
B. REASON
(1) History
During assembly of the section 19 skin to Frame (FR) 98 joint, it has been identified
that the gaps at nut to FR flange seat are out of tolerance for 8 fasteners between
stringer (STGR) 15 and 17, 4 Left Hand (LH) and 4 Right Hand (RH) sides. The
investigation performed reveals that the areas to be riveted present higher inclination
than the inclination that can be accepted by the fasteners defined on the engineering
drawings. From the structural analysis performed it is found that the gaps out of
tolerance at these positions are not acceptable from Fatigue & Damage perspective.
(2) Objective/Action
This Service Bulletin provides the necessary instructions to remove the affected
fasteners, inspect the area and replace the fasteners with new self-aligning nuts.
Detailed visual inspection of adjacent areas is required to ensure that no effects have
extended to those areas.
(3) Advantages
Accomplishment of this Service Bulletin will contribute to maintain the structural
integrity at the affected section 19 skin to FR 98 joint.
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE MANDATORY COST SAVING NO
A/C OPERATION
AFFECTED
NO VENDOR SB NO
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD YES
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO
NOTE: Service Bulletin must be accomplished.
D. MAINTENANCE CONFIGURATION
CONF 001
No specific aircraft maintenance configuration required.
CONF 002
No specific aircraft maintenance configuration required.
CONF 003
No specific aircraft maintenance configuration required.
CONF ALL
E. MATERIAL PRICE INFORMATION
CONF 001
(1) Installation of Self-aligning Nuts Frame 98

### Page 4

A350
SERVICE BULLETIN
SUMMARY
REV 00 Feb 21/20 A350-53-P057
Page 4
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Part kit 53P057C01R01 1 70.00 USD BOLTS, NUTS
Aircraft standard tools See SB See Note  
NOTE: Price information to be obtained from the given supplier.
CONF 002
(1) Installation of Self-aligning Nuts Frame 98
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Part kit 53P057C01R01 1 70.00 USD BOLTS, NUTS
Aircraft standard tools See SB See Note  
NOTE: Price information to be obtained from the given supplier.
CONF 003
(1) Installation of Self-aligning Nuts Frame 98
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Part kit 53P057C01R01 1 70.00 USD BOLTS, NUTS
Aircraft standard tools See SB See Note  
NOTE: Price information to be obtained from the given supplier.
CONF ALL
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
AAR CAL CCA CES CHH CPA CRK CSC DAL DLH ETH EVE FBU FIN FJI FWI HVN IBE MAS MAU
PAL QTR SAA SIA TAM THA
G. CONCURRENT REQUIREMENTS
None
H. NATURE OF THE WORK
CONF 001
(1) Installation of Self-aligning Nuts Frame 98

### Page 5

A350
SERVICE BULLETIN
SUMMARY
REV 00 Feb 21/20 A350-53-P057
Page 5
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
AIRCRAFT YES
EQUIPMENT NO
CONF 002
(1) Installation of Self-aligning Nuts Frame 98
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
AIRCRAFT YES
EQUIPMENT NO
CONF 003
(1) Installation of Self-aligning Nuts Frame 98
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
AIRCRAFT YES
EQUIPMENT NO
CONF ALL
I. MANPOWER
CONF 001
(1) Installation of Self-aligning Nuts Frame 98
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
MANPOWER
TOTAL MAN-HOURS 7.00 h
ELAPSED TIME (HOURS) 4.00 h
CONF 002
(1) Installation of Self-aligning Nuts Frame 98
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
MANPOWER
TOTAL MAN-HOURS 7.00 h
ELAPSED TIME (HOURS) 4.00 h
CONF 003
(1) Installation of Self-aligning Nuts Frame 98
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
MANPOWER
TOTAL MAN-HOURS 7.00 h
ELAPSED TIME (HOURS) 4.00 h

### Page 6

A350
SERVICE BULLETIN
SUMMARY
Figure ICN-A350-A-53XXP057-A-FAPE3-059EF-A-003-01 SHEET 1/1
REV 00 Feb 21/20 A350-53-P057General overview
Page 6
CONF ALL
J. GENERAL OVERVIEW
CONF ALL
Z310
FR98
A
A
B
FR98
FWD
LH SHOWN
RH SYMMETRICAL
VIEW LOOKING OUTBD
B
INSTALLATION OF
SELF-ALIGNING NUTS
FR99 FR97
STGR13LH
STGR14LH
STGR17LH
STGR18LH
LOWER BEAM ASSEMBLY
ICN-A350-A-53XXP057-A-FAPE3-059EF-A-003-01

### Page 7

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 7
ATA SYSTEM: 53
TITLE: FUSELAGE - CONE/REAR FUSELAGE - INSTALL SELF-ALIGNING NUTS
AT FRAME 98 FEET BETWEEN STRINGER 15/17 (LH/RH)
1. PLANNING INFORMATION
A. APPLICABILITY
NOTE: This modification is applicable by Service Bulletin only.
NOTE: The intent of this modification is achieved in production on aircraft with
Manufacturer Serial Number (MSN) (0307) and subsequent through modification No.
(114295L83015).
(1) Models
ON A/C 0005-0058, 0060-0064, 0066-0070, 0072-0087, 0089-0101, 0103-0107, 0109, 0111-
0117, 0119-0124, 0126-0130, 0132-0138, 0140, 0142-0151, 0153-0155, 0157-0160, 0162-
0165, 0167, 0168, 0170, 0172-0187, 0189-0193, 0195-0205, 0207-0214, 0216-0221, 0223,
0224, 0226-0228, 0230-0232, 0234-0240, 0243-0251, 0254-0257, 0259-0261, 0263-0265,
0267-0273, 0276-0285, 0287, 0289, 0291-0295, 0297, 0299-0303, 0305
350-941
CONF ALL
(2) Applicability by MSN
0005-0058 0060-0064 0066-0070 0072-0087 0089-0101 0103-0107 0109 0111-0117
0119-0124 0126-0130 0132-0138 0140 0142-0151 0153-0155 0157-0160 0162-0165
0167 0168 0170 0172-0187 0189-0193 0195-0205 0207-0214 0216-0221 0223 0224
0226-0228 0230-0232 0234-0240 0243-0251 0254-0257 0259-0261 0263-0265 0267-
0273 0276-0285 0287 0289 0291-0295 0297 0299-0303 0305
(3) MSN by configuration
CONF 001
MSN CONFIGURATION
0005 001
CONF 002
MSN CONFIGURATION
0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016
0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027
0028 0029 0030 0031 0032 0033 0034 0035 0036 0037 0038
0039 0040 0041 0042 0043 0044 0045 0046 0047 0048 0049
0050 0051 0052 0053 0054 0055 0056 0057 0058 0060 0061
0062 0063 0064 0066 0067 0068 0069 0070 0072 0073 0074
0075 0076 0077 0078 0079 0080 0081 0082 0083 0084 0085
0086 0087 0089 0090 0091 0092 0093 0094 0095 0096 0097
0098 0099 0100 0101 0103 0104 0105 0106 0107 0109 0111
0112 0113 0114 0115 0116 0117 0119 0120 0121 0122 0123
0124 0126 0127 0128 0129 0130 0132 0133 0134 0135 0136
0137 0138 0140 0142 0143 0144 0145 0146 0147 0148 0149
0150 0151 0153 0154 0155 0157 0158 0159 0160 0162 0163
0164 0165 0167 0168 0170 0172 0173 0174 0175 0176 0177
0178 0179 0180 0181 0182 0183 0184 0185 0186 0187 0189
0190 0191 0192 0193 0195 0196 0197 0198 0199 0200 0201
002

### Page 8

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 8
MSN CONFIGURATION
0202 0203 0204 0205 0207 0208 0209 0210 0211 0212 0213
0214
CONF 003
MSN CONFIGURATION
0216 0217 0218 0219 0220 0221 0223 0224 0226 0227 0228
0230 0231 0232 0234 0235 0236 0237 0238 0239 0240 0243
0244 0245 0246 0247 0248 0249 0250 0251 0254 0255 0256
0257 0259 0260 0261 0263 0264 0265 0267 0268 0269 0270
0271 0272 0273 0276 0277 0278 0279 0280 0281 0282 0283
0284 0285 0287 0289 0291 0292 0293 0294 0295 0297 0299
0300 0301 0302 0303 0305
003
CONF ALL
(4) Configuration definition
CONF 001
Configuration 001
Config. 001 is valid for aircraft on which MOD No. 109496L80576 is embodied.
CONF 001 retrofits following modifications: 115286L83020.
CONF 002
Configuration 002
Config. 002 is valid for aircraft on which MOD No. 109496L80576 and MOD No.
110254L80604 are not embodied.
CONF 002 retrofits following modifications: 115286L83020.
CONF 003
Configuration 003
Config. 003 is valid for aircraft on which MOD No. 110254L80604 is embodied.
CONF 003 retrofits following modifications: 115286L83020.
CONF ALL
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
During assembly of the section 19 skin to Frame (FR) 98 joint, it has been identified
that the gaps at nut to FR flange seat are out of tolerance for 8 fasteners between
stringer (STGR) 15 and 17, 4 Left Hand (LH) and 4 Right Hand (RH) sides. The
investigation performed reveals that the areas to be riveted present higher inclination
than the inclination that can be accepted by the fasteners defined on the engineering
drawings. From the structural analysis performed it is found that the gaps out of
tolerance at these positions are not acceptable from Fatigue & Damage perspective.
(2) Objective/Action
This Service Bulletin provides the necessary instructions to remove the affected
fasteners, inspect the area and replace the fasteners with new self-aligning nuts.
Detailed visual inspection of adjacent areas is required to ensure that no effects have
extended to those areas.

### Page 9

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 9
(3) Advantages
Accomplishment of this Service Bulletin will contribute to maintain the structural
integrity at the affected section 19 skin to FR 98 joint.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
T o accomplish this Service Bulletin it is necessary to:
(1) Installation of Self-aligning Nuts Frame 98
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
1 Remove the RH Fasteners
2 Perform NDT on RH Fastener Holes and DET Inspection on Frame 97, Frame
98, and Frame 99
3 Install the RH Fasteners
4 Remove the LH Fasteners
5 Perform NDT on LH Fastener Holes and DET Inspection on Frame 97, Frame
98, and Frame 99
6 Install the LH Fasteners
E. COMPLIANCE
CONF 001
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin must be done before 4817 flight cycles or
24085 flight hours from A/C first flight whichever occurs first.
This Service Bulletin has been classified Mandatory. It is expected that an
Airworthiness Directive (AD) published by the European Aviation Safety Agency (EASA)
will be issued to confirm this classification. It is anticipated that the AD will confirm the
(thresholds and/or intervals and/or date) given but reference should be made to the
AD for confirmation of the mandated accomplishment timescale.
CONF 002
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin must be done before 5431 flight cycles or
27155 flight hours from A/C first flight whichever occurs first.
This Service Bulletin has been classified Mandatory. It is expected that an
Airworthiness Directive (AD) published by the European Aviation Safety Agency (EASA)
will be issued to confirm this classification. It is anticipated that the AD will confirm the
(thresholds and/or intervals and/or date) given but reference should be made to the
AD for confirmation of the mandated accomplishment timescale.
CONF 003

### Page 10

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 10
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin must be done before 7303 flight cycles or
36515 flight hours from A/C first flight whichever occurs first.
This Service Bulletin has been classified Mandatory. It is expected that an
Airworthiness Directive (AD) published by the European Aviation Safety Agency (EASA)
will be issued to confirm this classification. It is anticipated that the AD will confirm the
(thresholds and/or intervals and/or date) given but reference should be made to the
AD for confirmation of the mandated accomplishment timescale.
CONF ALL
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER
CONF 001
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Installation of Self-aligning Nuts Frame 98
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
PREPARATION
Get Access 0.50 h
PROCEDURE
Remove the RH Fasteners 1.00 h
Perform NDT on RH Fastener Holes and DET Inspection on
Frame 97, Frame 98, and Frame 99
1.00 h
Install the RH Fasteners 1.00 h
Remove the LH Fasteners 1.00 h
Perform NDT on LH Fastener Holes and DET Inspection on
Frame 97, Frame 98, and Frame 99
1.00 h
Install the LH Fasteners 1.00 h
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP

### Page 11

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 11
Close-up 0.50 h
TOTAL MAN-HOURS 7.00 h
ELAPSED TIME (HOURS) 4.00 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix A
CONF 002
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Installation of Self-aligning Nuts Frame 98
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
PREPARATION
Get Access 0.50 h
PROCEDURE
Remove the RH Fasteners 1.00 h
Perform NDT on RH Fastener Holes and DET Inspection on
Frame 97, Frame 98, and Frame 99
1.00 h
Install the RH Fasteners 1.00 h
Remove the LH Fasteners 1.00 h
Perform NDT on LH Fastener Holes and DET Inspection on
Frame 97, Frame 98, and Frame 99
1.00 h
Install the LH Fasteners 1.00 h
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Close-up 0.50 h
TOTAL MAN-HOURS 7.00 h
ELAPSED TIME (HOURS) 4.00 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix A
CONF 003
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Installation of Self-aligning Nuts Frame 98

### Page 12

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 12
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
PREPARATION
Get Access 0.50 h
PROCEDURE
Remove the RH Fasteners 1.00 h
Perform NDT on RH Fastener Holes and DET Inspection on
Frame 97, Frame 98, and Frame 99
1.00 h
Install the RH Fasteners 1.00 h
Remove the LH Fasteners 1.00 h
Perform NDT on LH Fastener Holes and DET Inspection on
Frame 97, Frame 98, and Frame 99
1.00 h
Install the LH Fasteners 1.00 h
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Close-up 0.50 h
TOTAL MAN-HOURS 7.00 h
ELAPSED TIME (HOURS) 4.00 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix A
CONF ALL
H. WEIGHT AND BALANCE
Not changed
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
CONF 001
(1) Installation of Self-aligning Nuts Frame 98
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
AIRCRAFT STRUCTURAL REPAIR (ASR)
A350-A-20-51-50-01ZZZ-25BZ-A A350-A-51-24-XX-01ZZZ-667Z-A
A350-A-51-42-21-01ZZZ-667Z-A A350-A-51-43-XX-01ZZZ-667Z-A
A350-A-51-75-12-00ZZZ-660Z-A A350-A-51-77-11-00ZZZ-660Z-A
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A

### Page 13

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 13
INTRODUCTION (INTRO)
A350-A-00-61-04-11ZZZ-018Z-D
MAINTENANCE PROCEDURE (MP)
A350-A-24-41-XX-00ZZZ-170Z-A A350-A-29-11-58-01ZZZ-520Z-A
A350-A-29-11-58-01ZZZ-720Z-A
A350-A-29-13-58-01ZZZ-520Z-A
A350-A-29-13-58-01ZZZ-720Z-A
A350-A-36-12-61-06ZZZ-520Z-A
A350-A-36-12-61-06ZZZ-720Z-A
NON DESTRUCTIVE TEST (NDT)
A350-A-51-96-50-00ZZZ-353Z-A A350-A-51-99-10-00ZZZ-35AZ-A
A350-A-53-5X-XX-0HZZZ-35AZ-A
TECHNICAL FOLLOW UP (TFU)
53.50.00007
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
CONF 002
(1) Installation of Self-aligning Nuts Frame 98
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
AIRCRAFT STRUCTURAL REPAIR (ASR)
A350-A-20-51-50-01ZZZ-25BZ-A A350-A-51-24-XX-01ZZZ-667Z-A
A350-A-51-42-21-01ZZZ-667Z-A A350-A-51-43-XX-01ZZZ-667Z-A
A350-A-51-75-12-00ZZZ-660Z-A A350-A-51-77-11-00ZZZ-660Z-A
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
INTRODUCTION (INTRO)
A350-A-00-61-04-11ZZZ-018Z-D
MAINTENANCE PROCEDURE (MP)
A350-A-24-41-XX-00ZZZ-170Z-A A350-A-29-11-58-01ZZZ-520Z-A
A350-A-29-11-58-01ZZZ-720Z-A
A350-A-29-13-58-01ZZZ-520Z-A
A350-A-29-13-58-01ZZZ-720Z-A
A350-A-36-12-61-06ZZZ-520Z-A
A350-A-36-12-61-06ZZZ-720Z-A
NON DESTRUCTIVE TEST (NDT)
A350-A-51-96-50-00ZZZ-353Z-A A350-A-51-99-10-00ZZZ-35AZ-A
A350-A-53-5X-XX-0HZZZ-35AZ-A
TECHNICAL FOLLOW UP (TFU)
53.50.00007

### Page 14

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 14
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
CONF 003
(1) Installation of Self-aligning Nuts Frame 98
(a) T ask set A350-A-53-XX-P057-01000-93AA-A Installation of Self-aligning Nuts
Frame 98
AIRCRAFT STRUCTURAL REPAIR (ASR)
A350-A-20-51-50-01ZZZ-25BZ-A A350-A-51-24-XX-01ZZZ-667Z-A
A350-A-51-42-21-01ZZZ-667Z-A A350-A-51-43-XX-01ZZZ-667Z-A
A350-A-51-75-12-00ZZZ-660Z-A A350-A-51-77-11-00ZZZ-660Z-A
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
INTRODUCTION (INTRO)
A350-A-00-61-04-11ZZZ-018Z-D
MAINTENANCE PROCEDURE (MP)
A350-A-24-41-XX-00ZZZ-170Z-A A350-A-29-11-58-01ZZZ-520Z-A
A350-A-29-11-58-01ZZZ-720Z-A
A350-A-29-13-58-01ZZZ-520Z-A
A350-A-29-13-58-01ZZZ-720Z-A
A350-A-36-12-61-06ZZZ-520Z-A
A350-A-36-12-61-06ZZZ-720Z-A
NON DESTRUCTIVE TEST (NDT)
A350-A-51-96-50-00ZZZ-353Z-A A350-A-51-99-10-00ZZZ-35AZ-A
A350-A-53-5X-XX-0HZZZ-35AZ-A
TECHNICAL FOLLOW UP (TFU)
53.50.00007
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
CONF ALL
K. PUBLICATION AFFECTED
None
L. INDUSTRY SUPPORT INFORMATION
AIRBUS will share the costs of accomplishment of this Service Bulletin by providing the kits
at no charge for orders placed before Dec 31/22.
AIRBUS will credit the man hours indicated in this Service Bulletin at the agreed in-house
warranty labor rate for claims received no later than 90 days after completion of the last
affected aircraft of your fleet, for the accomplishment of this Service Bulletin before Dec 31/
22.
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department: monitored.retrofit@airbus.com.

### Page 15

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 15
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
CONF 001
Material for task set A350-A-53-XX-P057-01000-93AA-A Installation of Self-
aligning Nuts Frame 98
MATERIAL QTY SEE NOTES
Aircraft standard tools See SB
Consumables See SB
Part kit 53P057C01R01 1
CONF 002
Material for task set A350-A-53-XX-P057-01000-93AA-A Installation of Self-
aligning Nuts Frame 98
MATERIAL QTY SEE NOTES
Aircraft standard tools See SB
Consumables See SB
Part kit 53P057C01R01 1
CONF 003
Material for task set A350-A-53-XX-P057-01000-93AA-A Installation of Self-
aligning Nuts Frame 98
MATERIAL QTY SEE NOTES
Aircraft standard tools See SB
Consumables See SB
Part kit 53P057C01R01 1
CONF ALL
B. TOOLING
CONF 001
Aircraft standard tools for task set A350-A-53-XX-P057-01000-93AA-A Installation
of Self-aligning Nuts Frame 98
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
98V53509002000 1 PLATFORM
CONF 002
Aircraft standard tools for task set A350-A-53-XX-P057-01000-93AA-A Installation
of Self-aligning Nuts Frame 98
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
98V53509002000 1 PLATFORM
CONF 003
Aircraft standard tools for task set A350-A-53-XX-P057-01000-93AA-A Installation
of Self-aligning Nuts Frame 98
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
98V53509002000 1 PLATFORM

### Page 16

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 16
CONF ALL
C. CONSUMABLES
CONF 001
Consumables for task set A350-A-53-XX-P057-01000-93AA-A Installation of Self-
aligning Nuts Frame 98
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
04DAB2
Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04JME4 T op Coat Polyurethane - -Grey InternalStructure
06AAC1 Polysulfide Sealant -General Purpose Interfay
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
CONF 002
Consumables for task set A350-A-53-XX-P057-01000-93AA-A Installation of Self-
aligning Nuts Frame 98
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
04DAB2
Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04JME4 T op Coat Polyurethane - -Grey InternalStructure
06AAC1 Polysulfide Sealant -General Purpose Interfay
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
CONF 003
Consumables for task set A350-A-53-XX-P057-01000-93AA-A Installation of Self-
aligning Nuts Frame 98
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
04DAB2
Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04JME4 T op Coat Polyurethane - -Grey InternalStructure
06AAC1 Polysulfide Sealant -General Purpose Interfay
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton

### Page 17

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 17
CONF ALL
D. LIST OF NEW PARTS
Part kit 53P057C01R01
Cost 70.00 USD
Availability 230 d (calendar days from receipt of order)
Procurement address  
NOTE(S)
AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
Phone: +49 40 743 51775
E-mail: airbus.kit@airbus.com
Internet: http://spares.airbus.com
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
3 EN6114K6-10 4 BOLT
4 ASNA2537-6 4 NUT
5 EN6114K5-8 4 BOLT
6 ASNA2537-5 4 NUT
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
E. LIST OF EXISTING PARTS
No parts

### Page 18

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 18
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A350-A-53-XX-P057-01000-93AA-A
Installation of Self-aligning Nuts Frame 98
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESP Ref. ESP A350-A-20-55-XX-
01ZZZ-042Z-A.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including RC paragraph contained herein, contact
AIRBUS for further instructions and approval.
NOTE: Discarded parts must be managed at the operator's discretion.
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
CONF 001
TOTAL MAN-HOURS 7.00 h

### Page 19

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 19
CONF 002
TOTAL MAN-HOURS 7.00 h
CONF 003
TOTAL MAN-HOURS 7.00 h
CONF 001
ELAPSED TIME (HOURS) 4.00 h
CONF 002
ELAPSED TIME (HOURS) 4.00 h
CONF 003
ELAPSED TIME (HOURS) 4.00 h
CONF ALL
B. PREPARATION
(1) Task A350-A-53-XX-P057-01001-540A-A - Get Access
WARNING: YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU
START WORK:
- IN THE NLG OR MLG BAYS
- ON THE THS OR IN THE REAR FUSELAGE
- ON TOP OF THE WINGS OR PYLONS.
WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU
OR CAUSE YOU INJURY.
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Material necessary to do the job
Aircraft standard tools
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
98V53509002000 1 PLATFORM
Referenced Information
Manuals/Drawings References/Sheets
INTRO A350-A-00-61-04-11ZZZ-018Z-D
MP
A350-A-24-41-XX-00ZZZ-170Z-A
A350-A-29-11-58-01ZZZ-520Z-A
A350-A-29-13-58-01ZZZ-520Z-A
A350-A-36-12-61-06ZZZ-520Z-A
Procedure
NOTE: For the basic Aircraft configuration, refer to Ref. INTRO A350-A-00-61-04-
11ZZZ-018Z-D “Introduction”.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. MP A350-A-24-
41-XX-00ZZZ-170Z-A.
(b) Put an access platform in position below access doors 311AB and 311BB.
(c) Gain access to the aft fuselage through access door 311AB.
NOTE: Be careful not to step on a closed access door.

### Page 20

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 20
(d) Install the tools to access gain access to the work area.
1 CENTRAL PLATFORM-
S19
98V53509002000  
(e) If required disconnect the Aft Green T emperature Control Valve, refer to Ref. MP
A350-A-29-11-58-01ZZZ-520Z-A.
(f) If required disconnect the Aft Yellow T emperature Control Valve, refer to Ref. MP
A350-A-29-13-58-01ZZZ-520Z-A.
(g) If required remove the Bleed Air Duct, refer to Ref. MP A350-A-36-12-61-06ZZZ-
520Z-A.
C. PROCEDURE
(1) Task A350-A-53-XX-P057-01001-520A-A - Remove the RH Fasteners
WARNING: YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU
START WORK:
- IN THE NLG OR MLG BAYS
- ON THE THS OR IN THE REAR FUSELAGE
- ON TOP OF THE WINGS OR PYLONS.
WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU
OR CAUSE YOU INJURY.
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Door 311AB
300 Work location From Stringer 15 to Stringer 17Frame 98
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-42-21-01ZZZ-667Z-AA350-A-51-77-11-00ZZZ-660Z-A
Procedure
(a) The Standard Practices given in this procedure are:

### Page 21

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 21
1 Remove and install fasteners in accordance with Ref. ASR A350-A-51-42-21-
01ZZZ-667Z-A.
2 Get cleaning process in accordance with Ref. ASR A350-A-51-77-11-00ZZZ-
660Z-A.
(b) Remove as shown on Ref. Fig. Fastener Removal View B and View C.
4 FASTENER     Discard
(c) Clean the work area with:
  T extile - Lint free Cotton14SBA1  
and
  Non Aqueous Cleaner -
General
08BAA9

### Page 22

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EJ-A-003-01 SHEET 1/2
REV 00 Feb 21/20 A350-53-P057Fastener Removal
Page 22
CONF ALL
Z310
FR98
A
A
B
FR98
FWD
LH SHOWN
RH SYMMETRICAL
VIEW LOOKING OUTBD
B
FR99 FR97
STGR13LH
STGR14LH
STGR17LH
STGR18LH
LOWER BEAM ASSEMBLY
C
D
ICN-A350-A-53XXP057-A-FAPE3-059EJ-A-003-01

### Page 23

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EK-A-002-01 SHEET 2/2
REV 00 Feb 21/20 A350-53-P057Fastener Removal
Page 23
CONF ALL
LH SHOWN
RH SYMMETRICAL
LH SHOWN
RH SYMMETRICAL
C
D
STGR17LH
FR98
FR98
LOWER BEAM 
ASSEMBLY
LOWER BEAM 
ASSEMBLY
REMOVE AND DISCARD FASTENER
STGR17LH
FR99
FR97
FR97
FR99
NOTE:
FASTENER NOT AFFECTED
ICN-A350-A-53XXP057-A-FAPE3-059EK-A-002-01

### Page 24

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 24
(2) Task A350-A-53-XX-P057-01001-353A-A - Perform NDT on RH Fastener Holes
and DET Inspection on Frame 97, Frame 98, and Frame 99
WARNING: YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU
START WORK:
- IN THE NLG OR MLG BAYS
- ON THE THS OR IN THE REAR FUSELAGE
- ON TOP OF THE WINGS OR PYLONS.
WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU
OR CAUSE YOU INJURY.
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Door 311AB
300 Work location From Frame 97 to Frame 99From Stringer 12 to Stringer 18
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
NDT
A350-A-51-96-50-00ZZZ-353Z-A
A350-A-51-99-10-00ZZZ-35AZ-A
A350-A-53-5X-XX-0HZZZ-35AZ-A
Procedure
(a) Perform the NDT of the modification area, refer to Ref. Fig. Area Inspection.
1 Do a rotating probe test of the fastener holes, refer to Ref. NDT A350-A-51-
96-50-00ZZZ-353Z-A and refer to Ref. Fig. Area Inspection Sheet 2, View C
and View D.
2 Do an eddy current inspection of the surrounding flange in accordance
with Ref. NDT A350-A-53-5X-XX-0HZZZ-35AZ-A and refer to Ref. Fig. Area
Inspection Sheet 2, View C and View D.
3 Do a detailed inspection of the Frame 98, Frame 97, and Frame 99, refer
to Ref. NDT A350-A-51-99-10-00ZZZ-35AZ-A and refer to Ref. Fig. Area
Inspection Sheet 1, View B.
4 In case of findings:
a Contact AIRBUS for repair instructions.
5 In case of no findings:
a Continue to Ref. T ask A350-A-53-XX-P057-01ZZZ-720Z-A.

### Page 25

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EG-A-003-01 SHEET 1/2
REV 00 Feb 21/20 A350-53-P057Area Inspection
Page 25
CONF ALL
Z310
A
A
FR97
FR98
B
C
D
B
NOTE:
INSPECTION AREA
LH SHOWN
RH SYMMETRICAL
LOWER BEAM ASSEMBLY
FR98 FR97
STGR18LH
STGR12LH
FR99
ICN-A350-A-53XXP057-A-FAPE3-059EG-A-003-01

### Page 26

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EH-A-004-01 SHEET 2/2
REV 00 Feb 21/20 A350-53-P057Area Inspection
Page 26
CONF ALL
01
02
03
LH SHOWN
RH SYMMETRICAL
LH SHOWN
RH SYMMETRICAL
C
D
FR98
FR98
LOWER BEAM 
ASSEMBLY
LOWER BEAM 
ASSEMBLY
NOTE:
CLEAN THE WORK AREA WITH 14SBA1 AND 08BAA901
02
03
DO A ROTOTEST OF THE FASTENER HOLES
DO AN HFEC OF THE FLANGES, RADII, SURFACE
STGR17LH
STGR17LH
FASTENER NOT AFFECTED
01
02
03
AROUND THE FASTENER HOLES, AND THE EDGE
OF THE FORWARD FLANGE
ICN-A350-A-53XXP057-A-FAPE3-059EH-A-004-01

### Page 27

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 27
(3) Task A350-A-53-XX-P057-01001-720A-A - Install the RH Fasteners
WARNING: YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU
START WORK:
- IN THE NLG OR MLG BAYS
- ON THE THS OR IN THE REAR FUSELAGE
- ON TOP OF THE WINGS OR PYLONS.
WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU
OR CAUSE YOU INJURY.
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Door 311AB
300 Work location Frame 98From Stringer 15 to Stringer 17
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
04DAB2
Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04JME4 T op Coat Polyurethane - -Grey InternalStructure
06AAC1 Polysulfide Sealant -General Purpose Interfay
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
Part kit 53P057C01R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
3 EN6114K6-10 2 BOLT
4 ASNA2537-6 2 NUT
5 EN6114K5-8 2 BOLT
6 ASNA2537-5 2 NUT
Referenced Information
Manuals/Drawings References/Sheets
ASR
A350-A-20-51-50-01ZZZ-25BZ-A
A350-A-51-24-XX-01ZZZ-667Z-A
A350-A-51-42-21-01ZZZ-667Z-A

### Page 28

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 28
Manuals/Drawings References/Sheets
A350-A-51-43-XX-01ZZZ-667Z-A
A350-A-51-75-12-00ZZZ-660Z-A
A350-A-51-77-11-00ZZZ-660Z-A
CML CONSUMABLE MATERIAL LIST (CML)
Procedure
(a) The Standard Practices given in this procedure are:
1 Remove and install fasteners in accordance with Ref. ASR A350-A-51-42-21-
01ZZZ-667Z-A.
2 Apply sealant in accordance with Ref. ASR A350-A-51-24-XX-01ZZZ-667Z-A.
3 T o torque tighten the standard threaded fasteners, refer to Ref. ASR A350-
A-20-51-50-01ZZZ-25BZ-A.
4 For the specification of Material application codes given in this Service
Bulletin, refer to Ref. CML.
5 If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in ASR Data Module 51-4, then a fastener of
the same specification, or an approved substitute, with a length which
meets the installation standards given in (ASR Data Module 51-4 or SRM
Chapter 51) may be used. In addition, washers may be installed for
fastener grip length in accordance with (ASR Data Module 51-4 or SRM
Chapter 51).
6 Get alternative and substitute fastener data in accordance with Ref. ASR
A350-A-51-43-XX-01ZZZ-667Z-A.
7 Get cleaning process in accordance with Ref. ASR A350-A-51-77-11-00ZZZ-
660Z-A.
8 Repair the paint coating in accordance with Ref. ASR A350-A-51-75-12-
00ZZZ-660Z-A.
(b) Clean the installation area with:
  T extile - Lint free Cotton14SBA1  
made moist with:
  Non Aqueous Cleaner -
General
08BAA9  
(c) Wet install the new fasteners, refer to Ref. Fig. Fastener Installation.
2 BOLT EN6114K6-10 Item 3
2 NUT-HEXAGONAL,SELF-
LOCKING,BALL,BIHEX,F
USE
ASNA2537-6 Item 4
with
  Polysulfide Sealant
- General Purpose
Interfay
06AAC1  
(d) T orque the fasteners between 17.4 Nm (154.00 lbf.in) and 21 Nm (185.86 lbf.in).
(e) Wet install the new fasteners, refer to Ref. Fig. Fastener Installation.
2 BOLT EN6114K5-8 Item 5

### Page 29

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 29
2 NUT-HEXAGONAL,SELF-
LOCKING,BALL,BIHEX,F
USE
ASNA2537-5 Item 6
with
  Polysulfide Sealant
- General Purpose
Interfay
06AAC1  
(f) T orque the fasteners between 10.0 Nm (88.50 lbf.in) and 13.1 Nm (115.94 lbf.in).
(g) Apply protection to the fasteners, use :
  Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04DAB2  
  T op Coat Polyurethane -
- Grey InternalStructure
04JME4

### Page 30

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EL-A-003-01 SHEET 1/3
REV 00 Feb 21/20 A350-53-P057Fastener Installation
Page 30
CONF ALL
Z310
FR98
A
A
B
FR98
FWD
LH SHOWN
RH SYMMETRICAL
VIEW LOOKING OUTBD
B
FR99 FR97
STGR13LH
STGR14LH
STGR17LH
STGR18LH
LOWER BEAM ASSEMBLY
C
D
ICN-A350-A-53XXP057-A-FAPE3-059EL-A-003-01

### Page 31

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EM-A-002-01 SHEET 2/3
REV 00 Feb 21/20 A350-53-P057Fastener Installation
Page 31
CONF ALL
LH SHOWN
RH SYMMETRICAL
LH SHOWN
RH SYMMETRICAL
C
D
STGR17LH
FR98
FR98
LOWER BEAM 
ASSEMBLY
LOWER BEAM 
ASSEMBLY
STGR17LH
A
A
A
A
FR99
FR97
FR97
FR99
NOTE:
FASTENER NOT AFFECTED
SEE SHEET 03 FOR FASTENER TABLE
ICN-A350-A-53XXP057-A-FAPE3-059EM-A-002-01

### Page 32

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EN-A-003-01 SHEET 3/3
REV 00 Feb 21/20 A350-53-P057Fastener Installation
Page 32
CONF ALL
PRIMER (04DAB2)
TOP COAT (04JME4)
NUT
HOLE
SYMBOL ITEM PN DESCRIPTION
BOLT
BOLT
NUT
EN6114K6-10
ASNA2537-6
EN6114K5-8
3
4
5
MIN MAX
HOLE DIAMETER SIZE/FIT TYPE
9.514 mm
(0.3746 in)
9.552 mm
(0.3760 in)
LOW
CLEARANCE
NOTES
NUTASNA2537-56
01 02
7.927 mm
(0.3121 in)
7.964 mm
(0.3135 in)
LOW
CLEARANCE 01 02
NOTE:
WET INSTALL WITH MATERIAL No 06AAC101
SEE VIEW A-A FOR OVERCOATING SEALANT02
03 TOUCH UP TOP COAT AS REQUIRED TO MATCH AIRCRAFT PAINT SCHEME
03
FINAL
A A
BOLT
TYPICAL
ICN-A350-A-53XXP057-A-FAPE3-059EN-A-003-01

### Page 33

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 33
(4) Task A350-A-53-XX-P057-02001-520A-A - Remove the LH Fasteners
WARNING: YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU
START WORK:
- IN THE NLG OR MLG BAYS
- ON THE THS OR IN THE REAR FUSELAGE
- ON TOP OF THE WINGS OR PYLONS.
WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU
OR CAUSE YOU INJURY.
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Door 311AB
300 Work location Frame 98From Stringer 15 to Stringer 17
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-42-21-01ZZZ-667Z-AA350-A-51-77-11-00ZZZ-660Z-A
Procedure
(a) The Standard Practices given in this procedure are:
1 Remove and install fasteners in accordance with Ref. ASR A350-A-51-42-21-
01ZZZ-667Z-A.
2 Get cleaning process in accordance with Ref. ASR A350-A-51-77-11-00ZZZ-
660Z-A.
(b) Remove as shown on Ref. Fig. Fastener Removal View B and View C.
4 FASTENER     Discard
(c) Clean the work area with:
  T extile - Lint free Cotton14SBA1  
and

### Page 34

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 34
  Non Aqueous Cleaner -
General
08BAA9

### Page 35

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EJ-A-003-01 SHEET 1/2
REV 00 Feb 21/20 A350-53-P057Fastener Removal
Page 35
CONF ALL
Z310
FR98
A
A
B
FR98
FWD
LH SHOWN
RH SYMMETRICAL
VIEW LOOKING OUTBD
B
FR99 FR97
STGR13LH
STGR14LH
STGR17LH
STGR18LH
LOWER BEAM ASSEMBLY
C
D
ICN-A350-A-53XXP057-A-FAPE3-059EJ-A-003-01

### Page 36

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EK-A-002-01 SHEET 2/2
REV 00 Feb 21/20 A350-53-P057Fastener Removal
Page 36
CONF ALL
LH SHOWN
RH SYMMETRICAL
LH SHOWN
RH SYMMETRICAL
C
D
STGR17LH
FR98
FR98
LOWER BEAM 
ASSEMBLY
LOWER BEAM 
ASSEMBLY
REMOVE AND DISCARD FASTENER
STGR17LH
FR99
FR97
FR97
FR99
NOTE:
FASTENER NOT AFFECTED
ICN-A350-A-53XXP057-A-FAPE3-059EK-A-002-01

### Page 37

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 37
(5) Task A350-A-53-XX-P057-02001-353A-A - Perform NDT on LH Fastener Holes
and DET Inspection on Frame 97, Frame 98, and Frame 99
WARNING: YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU
START WORK:
- IN THE NLG OR MLG BAYS
- ON THE THS OR IN THE REAR FUSELAGE
- ON TOP OF THE WINGS OR PYLONS.
WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU
OR CAUSE YOU INJURY.
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Door 311AB
300 Work location From Frame 97 to Frame 99From Stringer 12 to Stringer 18
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Non-Destructive T esting
Referenced Information
Manuals/Drawings References/Sheets
NDT
A350-A-51-96-50-00ZZZ-353Z-A
A350-A-51-99-10-00ZZZ-35AZ-A
A350-A-53-5X-XX-0HZZZ-35AZ-A
Procedure
(a) Perform the NDT of the modification area, refer to Ref. Fig. Area Inspection.
1 Do a rotating probe test of the fastener holes, refer to Ref. NDT A350-A-51-
96-50-00ZZZ-353Z-A and refer to Ref. Fig. Area Inspection Sheet 2, View C
and View D.
2 Do an eddy current inspection of the surrounding flange in accordance
with Ref. NDT A350-A-53-5X-XX-0HZZZ-35AZ-A and refer to Ref. Fig. Area
Inspection Sheet 2, View C and View D.
3 Do a detailed inspection of the Frame 98, Frame 97, and Frame 99, refer
to Ref. NDT A350-A-51-99-10-00ZZZ-35AZ-A and refer to Ref. Fig. Area
Inspection Sheet 1, View B.
4 In case of findings:
a Contact AIRBUS for repair instructions.
5 In case of no findings:
a Continue to Ref. T ask A350-A-53-XX-P057-02ZZZ-720Z-A.

### Page 38

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EG-A-003-01 SHEET 1/2
REV 00 Feb 21/20 A350-53-P057Area Inspection
Page 38
CONF ALL
Z310
A
A
FR97
FR98
B
C
D
B
NOTE:
INSPECTION AREA
LH SHOWN
RH SYMMETRICAL
LOWER BEAM ASSEMBLY
FR98 FR97
STGR18LH
STGR12LH
FR99
ICN-A350-A-53XXP057-A-FAPE3-059EG-A-003-01

### Page 39

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EH-A-004-01 SHEET 2/2
REV 00 Feb 21/20 A350-53-P057Area Inspection
Page 39
CONF ALL
01
02
03
LH SHOWN
RH SYMMETRICAL
LH SHOWN
RH SYMMETRICAL
C
D
FR98
FR98
LOWER BEAM 
ASSEMBLY
LOWER BEAM 
ASSEMBLY
NOTE:
CLEAN THE WORK AREA WITH 14SBA1 AND 08BAA901
02
03
DO A ROTOTEST OF THE FASTENER HOLES
DO AN HFEC OF THE FLANGES, RADII, SURFACE
STGR17LH
STGR17LH
FASTENER NOT AFFECTED
01
02
03
AROUND THE FASTENER HOLES, AND THE EDGE
OF THE FORWARD FLANGE
ICN-A350-A-53XXP057-A-FAPE3-059EH-A-004-01

### Page 40

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 40
(6) Task A350-A-53-XX-P057-02001-720A-A - Install the LH Fasteners
WARNING: YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU
START WORK:
- IN THE NLG OR MLG BAYS
- ON THE THS OR IN THE REAR FUSELAGE
- ON TOP OF THE WINGS OR PYLONS.
WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU
OR CAUSE YOU INJURY.
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Door 311AB
300 Work location Frame 98From Stringer 15 to Stringer 17
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
04DAB2
Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04JME4 T op Coat Polyurethane - -Grey InternalStructure
06AAC1 Polysulfide Sealant -General Purpose Interfay
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
Part kit 53P057C01R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
3 EN6114K6-10 2 BOLT
4 ASNA2537-6 2 NUT
5 EN6114K5-8 2 BOLT
6 ASNA2537-5 2 NUT
Referenced Information
Manuals/Drawings References/Sheets
ASR
A350-A-20-51-50-01ZZZ-25BZ-A
A350-A-51-24-XX-01ZZZ-667Z-A
A350-A-51-42-21-01ZZZ-667Z-A

### Page 41

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 41
Manuals/Drawings References/Sheets
A350-A-51-43-XX-01ZZZ-667Z-A
A350-A-51-75-12-00ZZZ-660Z-A
A350-A-51-77-11-00ZZZ-660Z-A
CML CONSUMABLE MATERIAL LIST (CML)
Procedure
(a) The Standard Practices given in this procedure are:
1 Remove and install fasteners in accordance with Ref. ASR A350-A-51-42-21-
01ZZZ-667Z-A.
2 Apply sealant in accordance with Ref. ASR A350-A-51-24-XX-01ZZZ-667Z-A.
3 T o torque tighten the standard threaded fasteners, refer to Ref. ASR A350-
A-20-51-50-01ZZZ-25BZ-A.
4 For the specification of Material application codes given in this Service
Bulletin, refer to Ref. CML.
5 If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in ASR Data Module 51-4, then a fastener of
the same specification, or an approved substitute, with a length which
meets the installation standards given in (ASR Data Module 51-4 or SRM
Chapter 51) may be used. In addition, washers may be installed for
fastener grip length in accordance with (ASR Data Module 51-4 or SRM
Chapter 51).
6 Get alternative and substitute fastener data in accordance with Ref. ASR
A350-A-51-43-XX-01ZZZ-667Z-A.
7 Get cleaning process in accordance with Ref. ASR A350-A-51-77-11-00ZZZ-
660Z-A.
8 Repair the paint coating in accordance with Ref. ASR A350-A-51-75-12-
00ZZZ-660Z-A.
(b) Clean the installation area with:
  T extile - Lint free Cotton14SBA1  
made moist with:
  Non Aqueous Cleaner -
General
08BAA9  
(c) Wet install the new fasteners, refer to Ref. Fig. Fastener Installation.
2 BOLT EN6114K6-10 Item 3
2 NUT-HEXAGONAL,SELF-
LOCKING,BALL,BIHEX,F
USE
ASNA2537-6 Item 4
with
  Polysulfide Sealant
- General Purpose
Interfay
06AAC1  
(d) T orque the fasteners between 17.4 Nm (154.00 lbf.in) and 21 Nm (185.86 lbf.in).
(e)  
2 BOLT EN6114K5-8 Item 5

### Page 42

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 42
2 NUT-HEXAGONAL,SELF-
LOCKING,BALL,BIHEX,F
USE
ASNA2537-5 Item 6
with
  Polysulfide Sealant
- General Purpose
Interfay
06AAC1  
(f) T orque the fasteners between 10.0 Nm (88.50 lbf.in) and 13.1 Nm (115.94 lbf.in).
(g) Apply protection to the fasteners, use :
  Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04DAB2  
  T op Coat Polyurethane -
- Grey InternalStructure
04JME4

### Page 43

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EL-A-003-01 SHEET 1/3
REV 00 Feb 21/20 A350-53-P057Fastener Installation
Page 43
CONF ALL
Z310
FR98
A
A
B
FR98
FWD
LH SHOWN
RH SYMMETRICAL
VIEW LOOKING OUTBD
B
FR99 FR97
STGR13LH
STGR14LH
STGR17LH
STGR18LH
LOWER BEAM ASSEMBLY
C
D
ICN-A350-A-53XXP057-A-FAPE3-059EL-A-003-01

### Page 44

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EM-A-002-01 SHEET 2/3
REV 00 Feb 21/20 A350-53-P057Fastener Installation
Page 44
CONF ALL
LH SHOWN
RH SYMMETRICAL
LH SHOWN
RH SYMMETRICAL
C
D
STGR17LH
FR98
FR98
LOWER BEAM 
ASSEMBLY
LOWER BEAM 
ASSEMBLY
STGR17LH
A
A
A
A
FR99
FR97
FR97
FR99
NOTE:
FASTENER NOT AFFECTED
SEE SHEET 03 FOR FASTENER TABLE
ICN-A350-A-53XXP057-A-FAPE3-059EM-A-002-01

### Page 45

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP057-A-FAPE3-059EN-A-003-01 SHEET 3/3
REV 00 Feb 21/20 A350-53-P057Fastener Installation
Page 45
CONF ALL
PRIMER (04DAB2)
TOP COAT (04JME4)
NUT
HOLE
SYMBOL ITEM PN DESCRIPTION
BOLT
BOLT
NUT
EN6114K6-10
ASNA2537-6
EN6114K5-8
3
4
5
MIN MAX
HOLE DIAMETER SIZE/FIT TYPE
9.514 mm
(0.3746 in)
9.552 mm
(0.3760 in)
LOW
CLEARANCE
NOTES
NUTASNA2537-56
01 02
7.927 mm
(0.3121 in)
7.964 mm
(0.3135 in)
LOW
CLEARANCE 01 02
NOTE:
WET INSTALL WITH MATERIAL No 06AAC101
SEE VIEW A-A FOR OVERCOATING SEALANT02
03 TOUCH UP TOP COAT AS REQUIRED TO MATCH AIRCRAFT PAINT SCHEME
03
FINAL
A A
BOLT
TYPICAL
ICN-A350-A-53XXP057-A-FAPE3-059EN-A-003-01

### Page 46

A350
SERVICE BULLETIN
REV 00 Feb 21/20 A350-53-P057
Page 46
D. PREPARATION FOR TEST
None
E. TEST
None
F. CLOSE-UP
(1) Task A350-A-53-XX-P057-01001-740A-A - Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
MP
A350-A-29-11-58-01ZZZ-720Z-A
A350-A-29-13-58-01ZZZ-720Z-A
A350-A-36-12-61-06ZZZ-720Z-A
Procedure
(a) Put an access platform in position below access doors 311AB and 311BB.
(b) If required reconnect the Aft Green T emperature Control Valve, refer to Ref. MP
A350-A-29-11-58-01ZZZ-720Z-A.
(c) If required reconnect the Aft Yellow T emperature Control Valve, refer to Ref. MP
A350-A-29-13-58-01ZZZ-720Z-A.
(d) If removed reinstall the Bleed Air Duct, refer to Ref. MP A350-A-36-12-61-06ZZZ-
720Z-A.
(e) Close the aft fuselage through access door 311AB.
NOTE: Be careful not to step on a closed access door.
(f) Remove the access platform(s).
(g) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(h) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A350-A-53-XX-P057-01001-90AA-A - Admisitrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 47

A350
SERVICE BULLETIN
APPENDIX
REV 00 Feb 21/20 A350-53-P057
Page 47
APPENDIX
A. Manpower Gantt Chart
Manpower Gantt Chart
For an explanation of the man-hours and elapsed time, refer to the next page(s).

### Page 48

A350
SERVICE BULLETIN
APPENDIX
Figure ICN-A350-A-53XXP057-A-FAPE3-059EI-A-001-01 SHEET 1/1
REV 00 Feb 21/20 A350-53-P057Gantt Chart
Page 48
CONF ALL
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A350-53-P057
SB ELAPSED TIME
(HOURS)
GET ACCESS
MH ET/S
TOTAL MANHOURS
SB ELAPSED TIME
7.00
4.00
STEPS
0.50 0.50
0
REMOVE THE RH FASTENERS 1.00 1.00
PERFORM NDT ON RH FASTENER HOLES 1.00 1.00
INSTALL RH FASTENERS 1.00 1.00
REMOVE THE LH FASTENERS 1.00 1.00
INSTALL LH FASTENERS 1.00 1.00
CLOSE-UP 0.50 0.50
MH
ET/S:
PER
MANHOURS
ELAPSED TIME PER STEP
NUMBER OF PERSONS
01
02
THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
01
02
NOTE:
PER
1
1
1
1
1
1
1
1.00 1.001
:
:
IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
ARE NOT REFLECTED IN THIS GANTT CHART.
AND SURROUNDING AREA
PERFORM NDT ON LH FASTENER HOLES
AND SURROUNDING AREA
1 2 3 4
ICN-A350-A-53XXP057-A-FAPE3-059EI-A-001-01

### Page 49

A350
SERVICE BULLETIN
APPENDIX
REV 00 Feb 21/20 A350-53-P057
Page 49
B. REPORTING SHEET
TITLE: FUSELAGE - CONE/REAR FUSELAGE - INSTALL SELF-ALIGNING NUTS
AT FRAME 98 FEET BETWEEN STRINGER 15/17 (LH/RH)
MODIFICATION No.: 115286L83020
(1) SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance
and Flight Operations Products if it is duly reported to Airbus.
(2) GENERAL information
The SB Reporting policy is published in ISI 00.00.00135. This document provides
information regarding: the SB Reporting means and benefits, the update of
customized Maintenance Products and customized Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations
Products" for further information on the update of affected Flight Operations Products.
(3) SB Reporting procedure
Standard practice to report SB is to use the online reporting application on
AirbusWorld.
Refer to ISI 00.00.00179:
- For complete information on reporting means to Airbus, Question 2 "What are
the standard practices for SB Reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs,
Question 3 "What about the reporting of prerequisite Service Bulletins?"
NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.

### Page 50

A350
SERVICE BULLETIN
APPENDIX
REV 00 Feb 21/20 A350-53-P057
Page 50
C. QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin.
The reported data that you provide us will be used to analyse areas of difficulties and to
take corrective action to further improve the quality of our Service Bulletin.
We thank you for the time you have taken in completing this form.
Quality rating of this SB 4 3 2 1
Quality rating of the Accomplishment Instructions 4 3 2 1
Quality rating of the Illustrations 4 3 2 1
Is this SB easy to understand ? Y / N
NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score
If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.
Planning Material Instructions
X Applicability X T ooling X Preparation
X Reason X List of Materials
Operator Supplied
X Mod/Inspection
X Manpower X Kit content X T est
X References X Re-identification X Close-up
X Publication X Illustrations
X Industry Support
Comments :
Operator : Date :
Name/Title
Please return this form to :
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
Or via your Resident Customer Support Office.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
