# Airbus Service Bulletin A350-53-P061

Copy: No revision named ("SB A350-53-P061"), 67 pages: PDF https://openairdocs.org/files/sha256/38/51/385186c6ff037d35420181f0caebe9ba36b270e0c083e0ac99640292a5c8d394; text https://openairdocs.org/service-documents/airbus/a350-53-p061/file/385186c6ff03.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2020-1106, the docket of AD 2021-04-14. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A350-53-P061
- Page: https://openairdocs.org/service-documents/airbus/a350-53-p061

## Text (67 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2020-1106, the docket of AD 2021-04-14. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 1
CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
 
The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.
MANDATORY MANDATORY MANDATORY
ATA SYSTEM: 53
TITLE: FUSELAGE - MAIN STRUCTURE - INSPECTION OF THE SEAT RAILS
CORROSION PROTECTION AT FRAMES 40/41 AND 71/72
MODIFICATION No.:
None

### Page 2

A350
SERVICE BULLETIN
SUMMARY
REV 00 Mar 31/20 A350-53-P061
Page 2
ATA SYSTEM: 53
TITLE: FUSELAGE - MAIN STRUCTURE - INSPECTION OF THE SEAT RAILS
CORROSION PROTECTION AT FRAMES 40/41 AND 71/72
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR None
MINOR None
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
B. REASON
(1) History
During the assembly of spliced seat rails in production at Frame 40/ Frame 41 (Y
±280, Y±510, Y±840) and Frame 71/ Frame 72 (Y±280, Y±840), the seat rail crown
may need to be re-drilled at the junction due to tolerance constraints (to allow a seat
rail stud installation). After this potential rework, the crown rail protection should be
restored according to definition dossier.
The hole protection (alodine + primer + top coat) is requested in the operator task in
case of stud drilling but, during a quality review, it was discovered that the protection
treatment was not applied in production on dedicated aircraft. The seat rail splicing
strength is not impacted but at seat studs location, sufficient load carrying capability
cannot be ensured. Seats might no longer remain attached leading to severe injuries
of passengers under critical loading conditions.
T o support advanced inspection, before Inspection Service Bulletin (ISB) A350–53-P061
publication, on aircraft considered having seat studs installed in the loaded area at
Frame 71/ Frame 72 Y±280 (based on initial cabin layout), some T echnical Adaptations
(TAs) have been issued:
- TA 80724294/002/2019 issued on Manufacturing Serial Numbers (MSNs) 0075,
0085, 0093, 0101, 0109, 0118, 0119, 0128 and 0148
- TA 80734396/004/2020 issued on MSN 0254.
Inspections performed in accordance with the above TA, will be considered as a means
of partial compliance of ISB A350–53-P061.
An In-Service-Information (ISI) 53.31.00033 has been issued related to this topic. This
article provides the list of affected aircraft in loaded and unloaded configurations
based on quality production records and cabin layout definition at delivery. Affected
aircraft considered as initially loaded since delivery are MSNs 0075, 0085, 0093, 0101,
0109, 0118, 0119, 0128, 0148 and 0254 at location seat rails at Frame 71/ Frame 72 Y
+/- 280 only, with compliance time of 4 months after AD effective date (but not later
than Aug 31/20).

### Page 3

A350
SERVICE BULLETIN
SUMMARY
REV 00 Mar 31/20 A350-53-P061
Page 3
(2) Objective/Action
This ISB consists in a detailed inspection of the aluminium seat rails to determine the
presence of corrosion protection. If not, corrosion presence must also be determined
and repair instructions are provided if needed.
(3) Advantages
The accomplishment of this Service Bulletin enable to keep the corrosion at a low
level giving the chance for a light rework and to fulfill the requirements from the
airworthiness authorities.
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE MANDATORY COST SAVING NO
A/C OPERATION
AFFECTED
NO VENDOR SB NO
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD YES
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO
NOTE: Service Bulletin must be accomplished.
D. MAINTENANCE CONFIGURATION
No specific aircraft maintenance configuration required.
E. MATERIAL PRICE INFORMATION
(1) Do a Detailed Inspection of the Seat Studs Position between Frame 40 and
Frame 41 and between Frame 71 and Frame 72
(a) T ask set A350-A-53-XX-P061-02000-93BA-A Do a Detailed Inspection of the Seat
Studs Position between Frame 40 and Frame 41 and between Frame 71 and
Frame 72
No material
(2) Do a Detailed Inspection of the Seat Tracks Extremities at the Stud Location
from Frame 40 to Frame 41 and from Frame 71 to Frame 72
(a) T ask set A350-A-53-XX-P061-01000-93BA-A Do a Detailed Inspection of the Seat
Tracks Extremities at the Stud Location from Frame 40 to Frame 41 and from
Frame 71 to Frame 72
No material
(3) Reporting of the Inspection Results to AIRBUS
(a) T ask set A350-A-53-XX-P061-01000-93EA-A Reporting of the Inspection Results to
AIRBUS
No material
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):

### Page 4

A350
SERVICE BULLETIN
SUMMARY
REV 00 Mar 31/20 A350-53-P061
Page 4
82W AAR CAL CCA CES CHH CPA DAL DLH ETH FIN FWI HVN MAS MAU PAL QTR SIA THA
G. CONCURRENT REQUIREMENTS
None
H. NATURE OF THE WORK
(1) Do a Detailed Inspection of the Seat Studs Position between Frame 40 and
Frame 41 and between Frame 71 and Frame 72
(a) T ask set A350-A-53-XX-P061-02000-93BA-A Do a Detailed Inspection of the Seat
Studs Position between Frame 40 and Frame 41 and between Frame 71 and
Frame 72
AIRCRAFT YES
EQUIPMENT NO
(2) Do a Detailed Inspection of the Seat Tracks Extremities at the Stud Location
from Frame 40 to Frame 41 and from Frame 71 to Frame 72
(a) T ask set A350-A-53-XX-P061-01000-93BA-A Do a Detailed Inspection of the Seat
Tracks Extremities at the Stud Location from Frame 40 to Frame 41 and from
Frame 71 to Frame 72
AIRCRAFT YES
EQUIPMENT NO
(3) Reporting of the Inspection Results to AIRBUS
(a) T ask set A350-A-53-XX-P061-01000-93EA-A Reporting of the Inspection Results to
AIRBUS
AIRCRAFT NO
EQUIPMENT NO
I. MANPOWER
(1) Do a Detailed Inspection of the Seat Studs Position between Frame 40 and
Frame 41 and between Frame 71 and Frame 72
(a) T ask set A350-A-53-XX-P061-02000-93BA-A Do a Detailed Inspection of the Seat
Studs Position between Frame 40 and Frame 41 and between Frame 71 and
Frame 72
MANPOWER
TOTAL MAN-HOURS 5.10 h
ELAPSED TIME (HOURS) 3.10 h
(2) Do a Detailed Inspection of the Seat Tracks Extremities at the Stud Location
from Frame 40 to Frame 41 and from Frame 71 to Frame 72
(a) T ask set A350-A-53-XX-P061-01000-93BA-A Do a Detailed Inspection of the Seat
Tracks Extremities at the Stud Location from Frame 40 to Frame 41 and from
Frame 71 to Frame 72
MANPOWER
TOTAL MAN-HOURS 12.50 h
ELAPSED TIME (HOURS) 10.75 h
(3) Reporting of the Inspection Results to AIRBUS

### Page 5

A350
SERVICE BULLETIN
SUMMARY
REV 00 Mar 31/20 A350-53-P061
Page 5
(a) T ask set A350-A-53-XX-P061-01000-93EA-A Reporting of the Inspection Results to
AIRBUS
MANPOWER
TOTAL MAN-HOURS 0.50 h
ELAPSED TIME (HOURS) 0.50 h

### Page 6

A350
SERVICE BULLETIN
SUMMARY
Figure ICN-A350-A-53XXP061-A-FAPE3-05G5U-A-005-01 SHEET 1/2
REV 00 Mar 31/20 A350-53-P061General Overview
Page 6
J. GENERAL OVERVIEW
CONF ALL
F
W
D
VIEW LOOKING DOWN
01
-Y280+Y280
-Y510
-Y840
+Y510
+Y840
CL
FR40
FR41
F
W
D
VIEW LOOKING DOWN
01
-Y280+Y280
-Y510
-Y840
+Y510
+Y840
CL
FR40
FR41
F
W
D
VIEW LOOKING DOWN
01
-Y280+Y280
-Y510
-Y840
+Y510
+Y840
CL
FR40
FR41
F
W
D
VIEW LOOKING DOWN
01
FR40
FR41
-Y280+Y280
-Y510
-Y840
+Y510
+Y840
CL
DEPENDING ON THE AIRCRAFT CONFIGURATION, SEAT STUD LOCATION CAN DIFFER.01
F
W
D 01
+Y280+Y840 -Y280 -Y840CL
FR71
FR72
VIEW LOOKING DOWN
F
W
D
VIEW LOOKING DOWN
01
+Y280+Y840 -Y280 -Y840
CL
FR71
FR72
OR
F
W
D
VIEW LOOKING DOWN
01
+Y280+Y840 -Y280 -Y840
CL
FR71
FR72
OR
OROROR
A B C
Z260
D E F G
Z230
A
B
C
D E F G
NOTE:
H J K H J K H J K
H J KKJHKJHKJH
ICN-A350-A-53XXP061-A-FAPE3-05G5U-A-005-01

### Page 7

A350
SERVICE BULLETIN
SUMMARY
Figure ICN-A350-A-53XXP061-A-FAPE3-05KNQ-A-003-01 SHEET 2/2
REV 00 Mar 31/20 A350-53-P061General Overview
Page 7
CONF ALL
LOADED AREA, IF SEAT STUD INSTALLED WITHIN THIS AREA.
02 UNLOADED AREA, IF SEAT STUD INSTALLED WITHIN THIS AREA.
03
NOTE:
03
FWD
VIEW LOOKING DOWN
TYPICAL VIEW TYPICAL VIEW
SEAT STUD
TITANIUM SEAT TRACK
ALUMINUM SEAT TRACK
02
END OF SEAT RAIL/COUPLING AREA
SEAT TRACK
FWDJ K
ALUMINUM SEAT TRACK
TITANIUM SEAT TRACK
AREA TO BE INSPECTED
TYPICAL VIEW
F
W
D H
25.4 mm
(1.0 in)
ICN-A350-A-53XXP061-A-FAPE3-05KNQ-A-003-01

### Page 8

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 8
ATA SYSTEM: 53
TITLE: FUSELAGE - MAIN STRUCTURE - INSPECTION OF THE SEAT RAILS
CORROSION PROTECTION AT FRAMES 40/41 AND 71/72
1. PLANNING INFORMATION
A. APPLICABILITY
(1) Models
ON A/C 0088, 0102, 0110, 0118, 0141, 0161
350-1041
ON A/C 0074-0087, 0089-0101, 0103-0107, 0109, 0111-0117, 0119, 0124, 0126, 0128, 0130,
0132, 0133, 0135, 0138, 0142, 0144-0146, 0148, 0151, 0153, 0158-0160, 0162, 0163, 0172,
0174, 0176, 0180, 0183, 0185, 0187, 0189, 0190, 0197, 0201, 0204, 0216, 0217, 0228,
0230, 0239, 0254, 0260, 0261, 0280
350-941
CONF ALL
(2) Applicability by MSN
0074-0107 0109-0119 0124 0126 0128 0130 0132 0133 0135 0138 0141 0142 0144-
0146 0148 0151 0153 0158-0163 0172 0174 0176 0180 0183 0185 0187 0189 0190
0197 0201 0204 0216 0217 0228 0230 0239 0254 0260 0261 0280
(3) MSN by configuration
MSN CONFIGURATION
0074 0075 0076 0077 0078 0079 0080 0081 0082 0083 0084
0085 0086 0087 0088 0089 0090 0091 0092 0093 0094 0095
0096 0097 0098 0099 0100 0101 0102 0103 0104 0105 0106
0107 0109 0110 0111 0112 0113 0114 0115 0116 0117 0118
0119 0124 0126 0128 0130 0132 0133 0135 0138 0141 0142
0144 0145 0146 0148 0151 0153 0158 0159 0160 0161 0162
0163 0172 0174 0176 0180 0183 0185 0187 0189 0190 0197
0201 0204 0216 0217 0228 0230 0239 0254 0260 0261 0280
001
(4) Configuration definition
Configuration 001
CONF 001 is applicable for all the aircraft affected by this Service Bulletin as a
standard configuration.
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
During the assembly of spliced seat rails in production at Frame 40/ Frame 41 (Y
±280, Y±510, Y±840) and Frame 71/ Frame 72 (Y±280, Y±840), the seat rail crown
may need to be re-drilled at the junction due to tolerance constraints (to allow a seat
rail stud installation). After this potential rework, the crown rail protection should be
restored according to definition dossier.
The hole protection (alodine + primer + top coat) is requested in the operator task in
case of stud drilling but, during a quality review, it was discovered that the protection
treatment was not applied in production on dedicated aircraft. The seat rail splicing

### Page 9

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 9
strength is not impacted but at seat studs location, sufficient load carrying capability
cannot be ensured. Seats might no longer remain attached leading to severe injuries
of passengers under critical loading conditions.
T o support advanced inspection, before Inspection Service Bulletin (ISB) A350–53-P061
publication, on aircraft considered having seat studs installed in the loaded area at
Frame 71/ Frame 72 Y±280 (based on initial cabin layout), some T echnical Adaptations
(TAs) have been issued:
- TA 80724294/002/2019 issued on Manufacturing Serial Numbers (MSNs) 0075,
0085, 0093, 0101, 0109, 0118, 0119, 0128 and 0148
- TA 80734396/004/2020 issued on MSN 0254.
Inspections performed in accordance with the above TA, will be considered as a means
of partial compliance of ISB A350–53-P061.
An In-Service-Information (ISI) 53.31.00033 has been issued related to this topic. This
article provides the list of affected aircraft in loaded and unloaded configurations
based on quality production records and cabin layout definition at delivery. Affected
aircraft considered as initially loaded since delivery are MSNs 0075, 0085, 0093, 0101,
0109, 0118, 0119, 0128, 0148 and 0254 at location seat rails at Frame 71/ Frame 72 Y
+/- 280 only, with compliance time of 4 months after AD effective date (but not later
than Aug 31/20).
(2) Objective/Action
This ISB consists in a detailed inspection of the aluminium seat rails to determine the
presence of corrosion protection. If not, corrosion presence must also be determined
and repair instructions are provided if needed.
(3) Advantages
The accomplishment of this Service Bulletin enable to keep the corrosion at a low
level giving the chance for a light rework and to fulfill the requirements from the
airworthiness authorities.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
T o accomplish this Service Bulletin it is necessary to:
(1) Do a Detailed Inspection of the Seat Studs Position between Frame 40 and
Frame 41 and between Frame 71 and Frame 72
(a) T ask set A350-A-53-XX-P061-02000-93BA-A Do a Detailed Inspection of the Seat
Studs Position between Frame 40 and Frame 41 and between Frame 71 and
Frame 72
1 Do a Detailed Inspection of the Position of Seat Studs between Frame 40
and Frame 41 (Y+/- 280, Y+/-510, and Y+/- 840)
2 Do a Detailed Inspection of the Position of Seat Studs between Frame 71
and Frame 72 (Y+/- 280 and Y+/- 840)
(2) Do a Detailed Inspection of the Seat Tracks Extremities at the Stud Location
from Frame 40 to Frame 41 and from Frame 71 to Frame 72
(a) T ask set A350-A-53-XX-P061-01000-93BA-A Do a Detailed Inspection of the Seat
Tracks Extremities at the Stud Location from Frame 40 to Frame 41 and from
Frame 71 to Frame 72

### Page 10

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 10
1 Do a Detailed Inspection of the Seat Tracks Extremities at the Stud Location
between Frame 40 and Frame 41 (Y+/- 280, Y+/-510, and Y+/- 840)
2 Remove the Corrosion from the Seat Tracks Extremities at the Stud
Location between Frame 40 and Frame 41 (Y+/- 280, Y+/-510, and Y+/-
840)
3 Apply the Protection to the Seat Tracks Extremities at the Stud Location
between Frame 40 and Frame 41 (Y+/- 280, Y+/-510, and Y+/- 840)
4 Do a Detailed Inspection of the Seat Tracks Extremities at the Stud Location
between Frame 71 and Frame 72 (Y+/- 280 and Y+/- 840)
5 Remove the Corrosion from the Seat Tracks Extremities at the Stud
Location between Frame 71 and Frame 72 (Y+/- 280 and Y+/- 840)
6 Apply the Protection to the Seat Tracks Extremities at the Stud Location
between Frame 71 and Frame 72 (Y+/- 280 and Y+/- 840)
7 Do the Splice Repair on the Seat Tracks Extremities at the Stud Location
between Frame 71 and Frame 72 (Y+/- 280 and Y+/- 840)
(3) Reporting of the Inspection Results to AIRBUS
(a) T ask set A350-A-53-XX-P061-01000-93EA-A Reporting of the Inspection Results to
AIRBUS
1 Report to AIRBUS after the Detailed Inspection between Frame 40 and
Frame 41 (Y+/- 280, Y+/-510, and Y+/- 840)
2 Report to AIRBUS after the Detailed Inspection between Frame 71 and
Frame 72 (Y+/- 280 and Y+/- 840)
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin must be done within 4 month(s) after
Airworthiness Directive (AD) effective date but not later than Aug 31/20 whichever
occurs first.
This Service Bulletin has been classified Mandatory. It is expected that an
Airworthiness Directive (AD) published by the European Aviation Safety Agency (EASA)
will be issued to confirm this classification. It is anticipated that the AD will confirm
the thresholds given but reference should be made to the AD for confirmation of the
mandated accomplishment timescale.
T able 1, CONF 001 – Do a detailed inspection of the Aluminum Seat Tracks Extremities
at the Stud location between Frame 40 and Frame 41 for Protection and Corrosion
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
All aircraft Do a detailed
inspection of
the position
of seat studs
in accordance
with Ref. T ask
set A350-A-
Within 4
month(s) after
AD effective date
but not later
than Aug 31/20
None None

### Page 11

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 11
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
53-XX-P061-
02ZZZ-93BZ-A
If any seat stud
position is in
loaded area
Do a detailed
inspection of
the aluminum
seat tracks
extremities at
the stud location
between Frame
40 and Frame
41 (Y+/- 280,
Y+/- 510 and
Y+/- 840) for
protection and
corrosion in
accordance
with Ref. T ask
set A350-A-
53-XX-P061-
01ZZZ-93BZ-A
Within 4
month(s) from
AD issuance
but no later
than Aug 31/20
None None
If any seat stud
position is in
unloaded area
Do a detailed
inspection of
the aluminum
seat tracks
extremities at
the stud location
between Frame
40 and Frame
41 (Y+/- 280,
Y+/- 510 and
Y+/- 840) for
protection and
corrosion in
accordance
with Ref. T ask
set A350-A-
53-XX-P061-
01ZZZ-93BZ-A
Within 6 year(s)
from entry
into service
None None
If the area
is protected
Send the
completed
inspection
report sheet
to AIRBUS in
accordance with
Ref. T ask A350-
A-53-XX-P061-
01ZZZ-900Z-A
Within 1 month None None
  No further action None None None
If the area is
not protected
Do a visual
inspection for
the corrosion in
accordance with
Before next flight None None

### Page 12

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 12
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
Ref. T ask A350-
A-53-XX-P061-
01ZZZ-284Z-A
If no corrosion
found
Apply the
protection in
accordance with
Ref. T ask A350-
A-53-XX-P061-
01ZZZ-250Z-A
Before next flight None None
  Send the
completed
inspection
report sheet
to AIRBUS in
accordance with
Ref. T ask A350-
A-53-XX-P061-
01ZZZ-900Z-A
Within 1 month None None
  No further action None None None
If corrosion found Do not give
access to the
unserviceable
row of passenger
seats until
the corrosion
removal in
accordance with
Ref. T ask A350-
A-53-XX-P061-
01ZZZ-284Z-A
Within 1 year None None
  Send the
completed
inspection
report sheet
to AIRBUS in
accordance with
Ref. T ask A350-
A-53-XX-P061-
01ZZZ-900Z-A
Within 1 month None None
  OR
  Remove the
corrosion in
accordance with
Ref. T ask A350-
A-53-XX-P061-
01ZZZ-650Z-A
Before next flight None None
  Measure the
dimensions of
the seat rails in
accordance with
Ref. T ask A350-
Before next flight None None

### Page 13

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 13
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
A-53-XX-P061-
01ZZZ-284Z-A
If the dimensions
are within
the approved
tolerances
Apply the
protection in
accordance with
Ref. T ask A350-
A-53-XX-P061-
01ZZZ-250Z-A
Before next flight None None
  Send the
completed
inspection
report sheet
to AIRBUS in
accordance with
Ref. T ask A350-
A-53-XX-P061-
01ZZZ-900Z-A
Within 1 month None None
  No further action None None None
If the dimensions
are not within
the approved
tolerances
Contact AIRBUS
for further
instructions
None None None
T able 2, CONF 001 – Do a detailed inspection of the Aluminum Seat Tracks Extremities
at the Stud location between Frame 71 and Frame 72 for Protection and Corrosion
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
All aircraft Do a detailed
inspection of
the position
of seat studs
in accordance
with Ref. T ask
set A350-A-
53-XX-P061-
02ZZZ-93BZ-A
Within 4
month(s) after
AD effective date
but not later
than Aug 31/20
None None
If any seat stud
position is in
loaded area
Do a detailed
inspection of
the aluminum
seat tracks
extremities at
the stud location
between Frame
71 and Frame
72 (Y+/- 280
and Y+/- 840)
for protection
and corrosion
in accordance
with Ref. T ask
Within 4
month(s) from
AD issuance
but no later
than Aug 31/20
None None

### Page 14

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 14
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
set A350-A-
53-XX-P061-
01ZZZ-93BZ-A
If any seat stud
position is in
unloaded area
Do a detailed
inspection of
the aluminum
seat tracks
extremities at
the stud location
between Frame
71 and Frame
72 (Y+/- 280
and Y+/- 840)
for protection
and corrosion
in accordance
with Ref. T ask
set A350-A-
53-XX-P061-
01ZZZ-93BZ-A
Within 6 year(s)
from entry
into service
None None
If the area
is protected
Send the
completed
inspection
report sheet
to AIRBUS in
accordance with
Ref. T ask A350-
A-53-XX-P061-
02ZZZ-900Z-A
Within 1 month None None
  No further action None None None
If the area is
not protected
Do a visual
inspection for
the corrosion in
accordance with
Ref. T ask A350-
A-53-XX-P061-
02ZZZ-284Z-A
Before next flight None None
If no corrosion
found
Apply the
protection in
accordance with
Ref. T ask A350-
A-53-XX-P061-
02ZZZ-250Z-A
Before next flight None None
  Send the
completed
inspection
report sheet
to AIRBUS in
accordance with
Ref. T ask A350-
Within 1 month None None

### Page 15

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 15
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
A-53-XX-P061-
02ZZZ-900Z-A
  No further action None None None
If corrosion found Do not give
access to the
unserviceable
row of passenger
seats until
the corrosion
removal and
splice repair in
accordance with
Ref. T ask A350-
A-53-XX-P061-
02ZZZ-284Z-A
Within 1 year None None
  Send the
completed
inspection
report sheet
to AIRBUS in
accordance with
Ref. T ask A350-
A-53-XX-P061-
02ZZZ-900Z-A
Within 1 month None None
  OR
  Remove the
corrosion in
accordance with
Ref. T ask A350-
A-53-XX-P061-
02ZZZ-650Z-A
Before next flight None None
  Measure the
dimensions of
the seat rails in
accordance with
Ref. T ask A350-
A-53-XX-P061-
02ZZZ-284Z-A
Before next flight None None
If the dimensions
are within
the approved
tolerances
Apply the
protection in
accordance with
Ref. T ask A350-
A-53-XX-P061-
02ZZZ-250Z-A
Before next flight None None
  Send the
completed
inspection
report sheet
to AIRBUS in
accordance with
Ref. T ask A350-
Within 1 month None None

### Page 16

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 16
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
A-53-XX-P061-
02ZZZ-900Z-A
  No further action None None None
If the dimensions
are not within
the approved
tolerances
Apply the
protection in
accordance with
Ref. T ask A350-
A-53-XX-P061-
02ZZZ-250Z-A
Before next flight None None
  Do not give
access to the
unserviceable
row of passenger
seats until the
splice repair in
accordance with
Ref. T ask A350-
A-53-XX-P061-
02ZZZ-284Z-A
Within 1 year None None
  Send the
completed
inspection
report sheet
to AIRBUS in
accordance with
Ref. T ask A350-
A-53-XX-P061-
02ZZZ-900Z-A
Within 1 month None None
  OR
  Do the splice
repair in
accordance with
Ref. T ask A350-
A-53-XX-P061-
01ZZZ-690Z-A
Before next flight None None
  Send the
completed
inspection
report sheet
to AIRBUS in
accordance with
Ref. T ask A350-
A-53-XX-P061-
02ZZZ-900Z-A
Within 1 month None None
  No further action None None None
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.

### Page 17

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 17
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Do a Detailed Inspection of the Seat Studs Position between Frame 40 and
Frame 41 and between Frame 71 and Frame 72
(a) T ask set A350-A-53-XX-P061-02000-93BA-A Do a Detailed Inspection of the Seat
Studs Position between Frame 40 and Frame 41 and between Frame 71 and
Frame 72
PREPARATION
Job Set-up 0.10 h
PROCEDURE
Do a Detailed Inspection of the Position of Seat Studs
between Frame 40 and Frame 41 (Y+/- 280, Y+/-510, and Y
+/- 840)
1.00 h
Do a Detailed Inspection of the Position of Seat Studs
between Frame 71 and Frame 72 (Y+/- 280 and Y+/- 840)
1.00 h
PREPARATION FOR TEST
None
TEST
T est 1.00 h
CLOSE-UP
Close-up 2.00 h
TOTAL MAN-HOURS 5.10 h
ELAPSED TIME (HOURS) 3.10 h
NOTE: The minimum man-hours necessary to accomplish this Service Bulletin
are those for the Inspection. Depending on the inspection result,
additional man-hours can apply.
(2) Do a Detailed Inspection of the Seat Tracks Extremities at the Stud Location
from Frame 40 to Frame 41 and from Frame 71 to Frame 72
(a) T ask set A350-A-53-XX-P061-01000-93BA-A Do a Detailed Inspection of the Seat
Tracks Extremities at the Stud Location from Frame 40 to Frame 41 and from
Frame 71 to Frame 72
PREPARATION
Job Set-up 1.50 h
PROCEDURE
Do a Detailed Inspection of the Seat Tracks Extremities at
the Stud Location between Frame 40 and Frame 41 (Y+/-
280, Y+/-510, and Y+/- 840)
0.50 h

### Page 18

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 18
Remove the Corrosion from the Seat Tracks Extremities at
the Stud Location between Frame 40 and Frame 41 (Y+/-
280, Y+/-510, and Y+/- 840)
1.00 h
Apply the Protection to the Seat Tracks Extremities at the
Stud Location between Frame 40 and Frame 41 (Y+/- 280,
Y+/-510, and Y+/- 840)
0.50 h
Do a Detailed Inspection of the Seat Tracks Extremities at
the Stud Location between Frame 71 and Frame 72 (Y+/-
280 and Y+/- 840)
0.50 h
Remove the Corrosion from the Seat Tracks Extremities at
the Stud Location between Frame 71 and Frame 72 (Y+/-
280 and Y+/- 840)
1.00 h
Apply the Protection to the Seat Tracks Extremities at the
Stud Location between Frame 71 and Frame 72 (Y+/- 280
and Y+/- 840)
0.50 h
Do the Splice Repair on the Seat Tracks Extremities at the
Stud Location between Frame 71 and Frame 72 (Y+/- 280
and Y+/- 840)
4.00 h
PREPARATION FOR TEST
None
TEST
T est 1.00 h
CLOSE-UP
Close-up 2.00 h
TOTAL MAN-HOURS 12.50 h
ELAPSED TIME (HOURS) 10.75 h
NOTE: The minimum man-hours necessary to accomplish this Service Bulletin
are those for the Inspection. Depending on the inspection result,
additional man-hours can apply.
(3) Reporting of the Inspection Results to AIRBUS
(a) T ask set A350-A-53-XX-P061-01000-93EA-A Reporting of the Inspection Results to
AIRBUS
PREPARATION
None
PROCEDURE
Report to AIRBUS after the Detailed Inspection between
Frame 40 and Frame 41 (Y+/- 280, Y+/-510, and Y+/- 840)
0.25 h
Report to AIRBUS after the Detailed Inspection between
Frame 71 and Frame 72 (Y+/- 280 and Y+/- 840)
0.25 h
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
None

### Page 19

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 19
TOTAL MAN-HOURS 0.50 h
ELAPSED TIME (HOURS) 0.50 h
H. WEIGHT AND BALANCE
Not changed
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
(1) Do a Detailed Inspection of the Seat Studs Position between Frame 40 and
Frame 41 and between Frame 71 and Frame 72
(a) T ask set A350-A-53-XX-P061-02000-93BA-A Do a Detailed Inspection of the Seat
Studs Position between Frame 40 and Frame 41 and between Frame 71 and
Frame 72
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
INTRODUCTION (INTRO)
A350-A-00-61-04-11ZZZ-018Z-D
IN SERVICE INFORMATION (ISI)
53.31.00033
MAINTENANCE PROCEDURE (MP)
A350-A-24-41-XX-00ZZZ-170Z-A A350-A-25-21-46-00ZZZ-520Z-A
A350-A-25-21-46-00ZZZ-720Z-A
A350-A-25-21-46-01ZZZ-520Z-A
A350-A-25-21-46-01ZZZ-720Z-A
A350-A-25-21-46-05ZZZ-520Z-A
A350-A-25-21-46-05ZZZ-720Z-A
A350-A-25-21-46-08ZZZ-520Z-A
A350-A-25-21-46-08ZZZ-720Z-A
A350-A-25-21-46-09ZZZ-520Z-A
A350-A-25-21-46-09ZZZ-720Z-A
A350-A-25-21-46-0AZZZ-520Z-A
A350-A-25-21-46-0AZZZ-720Z-A
A350-A-25-21-46-0FZZZ-520Z-A
A350-A-25-21-46-0FZZZ-720Z-A
A350-A-25-21-46-0GZZZ-520Z-A
A350-A-25-21-46-0GZZZ-720Z-A
SYSTEM DESCRIPTION (SD)
A350-A-06-2X-XX-01ZZZ-04CZ-A A350-A-06-3X-XX-01ZZZ-04CZ-A

### Page 20

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 20
(2) Do a Detailed Inspection of the Seat Tracks Extremities at the Stud Location
from Frame 40 to Frame 41 and from Frame 71 to Frame 72
(a) T ask set A350-A-53-XX-P061-01000-93BA-A Do a Detailed Inspection of the Seat
Tracks Extremities at the Stud Location from Frame 40 to Frame 41 and from
Frame 71 to Frame 72
AIRCRAFT STRUCTURAL REPAIR (ASR)
A350-A-51-74-XX-02ZZZ-660Z-A A350-A-51-75-12-02ZZZ-660Z-A
A350-A-53-41-86-00ZZZ-664Z-A
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
INTRODUCTION (INTRO)
A350-A-00-61-04-11ZZZ-018Z-D
IN SERVICE INFORMATION (ISI)
53.31.00033
MAINTENANCE PROCEDURE (MP)
A350-A-24-41-XX-00ZZZ-170Z-A A350-A-25-21-46-00ZZZ-520Z-A
A350-A-25-21-46-00ZZZ-720Z-A
A350-A-25-21-46-01ZZZ-520Z-A
A350-A-25-21-46-01ZZZ-720Z-A
A350-A-25-21-46-05ZZZ-520Z-A
A350-A-25-21-46-05ZZZ-720Z-A
A350-A-25-21-46-08ZZZ-520Z-A
A350-A-25-21-46-08ZZZ-720Z-A
A350-A-25-21-46-09ZZZ-520Z-A
A350-A-25-21-46-09ZZZ-720Z-A
A350-A-25-21-46-0AZZZ-520Z-A
A350-A-25-21-46-0AZZZ-720Z-A
A350-A-25-21-46-0FZZZ-520Z-A
A350-A-25-21-46-0FZZZ-720Z-A
A350-A-25-21-46-0GZZZ-520Z-A
A350-A-25-21-46-0GZZZ-720Z-A
NON DESTRUCTIVE TEST (NDT)
A350-A-51-99-12-00ZZZ-311Z-A
SYSTEM DESCRIPTION (SD)
A350-A-06-2X-XX-01ZZZ-04CZ-A A350-A-06-3X-XX-01ZZZ-04CZ-A
(3) Reporting of the Inspection Results to AIRBUS

### Page 21

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 21
(a) T ask set A350-A-53-XX-P061-01000-93EA-A Reporting of the Inspection Results to
AIRBUS
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
IN SERVICE INFORMATION (ISI)
53.31.00033
K. PUBLICATION AFFECTED
None
L. INDUSTRY SUPPORT INFORMATION
AIRBUS will credit the man-hours indicated in this Service Bulletin at the agreed in-house
warranty labor rate for claims received no later than 90 days after completion of the last
affected aircraft of your fleet, for the accomplishment of this Service Bulletin within 2 years
after the initial issue date of the Service Bulletin.

### Page 22

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 22
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
No material for task set A350-A-53-XX-P061-02000-93BA-A Do a Detailed
Inspection of the Seat Studs Position between Frame 40 and Frame 41 and
between Frame 71 and Frame 72
Material for task set A350-A-53-XX-P061-01000-93BA-A Do a Detailed Inspection
of the Seat Tracks Extremities at the Stud Location from Frame 40 to Frame 41
and from Frame 71 to Frame 72
MATERIAL QTY SEE NOTES
Referenced consumables See SB
No material for task set A350-A-53-XX-P061-01000-93EA-A Reporting of the
Inspection Results to AIRBUS
B. TOOLING
No tools
C. CONSUMABLES
Referenced consumables for task set A350-A-53-XX-P061-01000-93BA-A Do a
Detailed Inspection of the Seat Tracks Extremities at the Stud Location from
Frame 40 to Frame 41 and from Frame 71 to Frame 72
T o accomplish this Service Bulletin it is necessary to use the consumable materials listed in
the subsequent referenced tasks.
Ref. ASR A350-A-51-74-XX-02ZZZ-660Z-A
Ref. ASR A350-A-51-75-12-02ZZZ-660Z-A
Ref. ASR A350-A-53-41-86-00ZZZ-664Z-A
D. LIST OF NEW PARTS
No parts
E. LIST OF EXISTING PARTS
No parts

### Page 23

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 23
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A350-A-53-XX-P061-02000-93BA-A
Do a Detailed Inspection of the Seat Studs Position between Frame 40 and Frame 41 and between
Frame 71 and Frame 72
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESP A350-A-20-55-XX-01ZZZ-
042Z-A.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including RC paragraph contained herein, contact
AIRBUS for further instructions and approval.
NOTE: The purpose of flowcharts is to supplement the information given in the Procedure and
Compliance paragraphs and not to serve as the primary source for tasks or compliance
times given in this Service Bulletin.
A. TASK SET ASSOCIATED INFORMATION
Task Manpower

### Page 24

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 24
TOTAL MAN-HOURS 5.10 h
ELAPSED TIME (HOURS) 3.10 h
B. PREPARATION
(1) Task A350-A-53-XX-P061-02001-540A-A - Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.10 h
Minimum Number of person 1
Elapsed Time 0.10 h
Referenced Information
Manuals/Drawings References/Sheets
INTRO A350-A-00-61-04-11ZZZ-018Z-D
MP A350-A-24-41-XX-00ZZZ-170Z-A
Procedure
NOTE: For the basic Aircraft configuration, refer to Ref. INTRO A350-A-00-61-04-
11ZZZ-018Z-D “Maintenance Procedure - Introduction”.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. MP A350-A-24-
41-XX-00ZZZ-170Z-A.
C. PROCEDURE
(1) Task A350-A-53-XX-P061-04001-346A-A - Do a Detailed Inspection of the
Position of Seat Studs between Frame 40 and Frame 41 (Y+/- 280, Y+/-510,
and Y+/- 840)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
230 Work location
From Frame 40 to Frame 41
From Y Coord +280mm to Y Coord -280mm
From Y Coord +510mm to Y Coord -510mm
From Y Coord +840mm to Y Coord -840mm
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 2
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
MP
A350-A-25-21-46-00ZZZ-520Z-A
A350-A-25-21-46-01ZZZ-520Z-A
A350-A-25-21-46-05ZZZ-520Z-A
A350-A-25-21-46-08ZZZ-520Z-A
A350-A-25-21-46-09ZZZ-520Z-A
A350-A-25-21-46-0AZZZ-520Z-A
A350-A-25-21-46-0FZZZ-520Z-A

### Page 25

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 25
Manuals/Drawings References/Sheets
A350-A-25-21-46-0GZZZ-520Z-A
SD A350-A-06-2X-XX-01ZZZ-04CZ-AA350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
2 For the Frame (FR) identification, refer to Ref. SD A350-A-06-2X-XX-01ZZZ-
04CZ-A.
(b) At the threshold given in the PLANNING INFORMATION paragraph E.(2):
Refer to Ref. Fig. Flowchart, FR 40/41.
1 Do a detailed inspection of the position of seat studs for loaded or
unloaded conditions at Y+/-280, Y+/- 540 and Y+/- 840 between Frame 40
and Frame 41.
Refer to Ref. Fig. Position of Seat Studs for Loaded and Unloaded
Conditions, FR 40/41.
a Record the position of the seat studs on the floor at Y+/-280, Y+/-
540 and Y+/- 840 between Frame 40 and Frame 41.
b Move the seats of the central row between Frame 40 and Frame 41
without removal, refer to Ref. MP A350-A-25-21-46-00ZZZ-520Z-A or
Ref. MP A350-A-25-21-46-01ZZZ-520Z-A or Ref. MP A350-A-25-21-46-
08ZZZ-520Z-A or Ref. MP A350-A-25-21-46-05ZZZ-520Z-A or Ref. MP
A350-A-25-21-46-09ZZZ-520Z-A or Ref. MP A350-A-25-21-46-0AZZZ-
520Z-A or Ref. MP A350-A-25-21-46-0FZZZ-520Z-A or Ref. MP A350-A-
25-21-46-0GZZZ-520Z-A.
c If any seat stud position is in the loaded area, do a detailed
inspection in accordance with Ref. T ask set A350-A-53-XX-P061-
01ZZZ-93BZ-A.
d If any seat stud position is in the unloaded area, depending on the
operator convenience and the threshold:
- Do a detailed inspection in accordance with Ref. T ask set A350-
A-53-XX-P061-01ZZZ-93BZ-A
OR
- Do the close-up in accordance with Ref. T ask A350-A-53-XX-
P061-02ZZZ-740Z-A.
NOTE: The threshold value for the loaded and unloaded condition is
different, refer to PLANNING INFORMATION paragraph E.(2)
T able 1.

### Page 26

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05G5T-A-004-01 SHEET 1/2
REV 00 Mar 31/20 A350-53-P061Flowchart, FR 40/41
Page 26
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE
PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
FOR THE ACCOMPLISHMENT TIMESCALE, REFER TO PARAGRAPH 1.E.(2).01
NOTE:
DO A DETAILED INSPECTION OF THE SEAT STUD CONDITION AT FRAMES 40/41
01
ANY SEAT
STUD IS INSTALLED
IN THE LOADED AREA
AT FRAMES 40/41
TRACK Y+/-280?
NO YES
AT THE SEAT STUD LOCATION BETWEEN FRAME 40 AND FRAME 41
DO A DETAILED INSPECTION OF THE ALUMINUM SEAT TRACKS EXTREMITIES
01
ANY SEAT
STUD IS INSTALLED
IN THE LOADED AREA
AT FRAMES 40/41
TRACK Y+/-840?
NO YES
A
ANY SEAT
STUD IS INSTALLED
IN THE LOADED AREA
AT FRAMES 40/41
TRACK Y+/-510?
NO YES
ICN-A350-A-53XXP061-A-FAPE3-05G5T-A-004-01

### Page 27

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05KNP-A-002-01 SHEET 2/2
REV 00 Mar 31/20 A350-53-P061Flowchart, FR 40/41
Page 27
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE
PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
FOR THE ACCOMPLISHMENT TIMESCALE, REFER TO PARAGRAPH 1.E.(2).01
NOTE:
APPLY THE PROTECTION OR
IS THE AREA
PROTECTED?YES
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
NO FURTHER ACTION
NO
IS CORROSION
FOUND?NO
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
NO FURTHER ACTION
YES
REMOVE THE CORROSION
MEASURE THE DIMENSIONS OF
THE SEAT RAILS
YES NO
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
NO FURTHER ACTION
CONTACT AIRBUS FOR FURTHER INSTRUCTIONS
ARE THE
DIMENSIONS WITHIN
THE APPROVED
TOLERANCES?
APPLY THE PROTECTION
DO NOT GIVE ACCESS TO THE UNSERVICEABLE
ROW OF PASSENGER SEATS 
UNTIL THE CORROSION REMOVAL
A
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
ICN-A350-A-53XXP061-A-FAPE3-05KNP-A-002-01

### Page 28

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05KQB-A-005-01 SHEET 1/1
REV 00 Mar 31/20 A350-53-P061Position of Seat Studs for Loaded and Unloaded Conditions, FR 40/41
Page 28
CONF ALL
02
Z230
A
-Y280+Y280
-Y510
-Y840
+Y510
+Y840 CL
F
W
D
FR40
FR41
VIEW LOOKING DOWN
SEATS NOT SHOWN
B C B C
A
LOADED AREA, IF SEAT STUD INSTALLED WITHIN THIS AREA.
01 UNLOADED AREA, IF SEAT STUD INSTALLED WITHIN THIS AREA.
02
BFWD
VIEW LOOKING DOWN
TYPICAL VIEW
C
TYPICAL VIEW
SEAT STUD
TITANIUM SEAT TRACK
ALUMINUM SEAT TRACK
NOTE:
01
END OF SEAT RAIL/COUPLING AREA
SEAT TRACK
FWD25.4 mm(1.0 in)
ICN-A350-A-53XXP061-A-FAPE3-05KQB-A-005-01

### Page 29

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 29
(2) Task A350-A-53-XX-P061-05001-346A-A - Do a Detailed Inspection of the
Position of Seat Studs between Frame 71 and Frame 72 (Y+/- 280 and Y+/-
840)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
260 Work location
From Frame 71 to Frame 72
From Y Coord +280mm to Y Coord -280mm
From Y Coord +840mm to Y Coord -840mm
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 2
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-25-21-46-00ZZZ-520Z-A
SD A350-A-06-2X-XX-01ZZZ-04CZ-AA350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
2 For the Frame (FR) identification, refer to Ref. SD A350-A-06-2X-XX-01ZZZ-
04CZ-A.
(b) At the threshold given in the PLANNING INFORMATION paragraph E.(2):
Refer to Ref. Fig. Flowchart, FR 71/72.
1 Do a detailed inspection of the position of seat studs for loaded or
unloaded conditions at Y+/-280 and Y+/- 840 between Frame 71 and Frame
72.
Refer to Ref. Fig. Position of Seat Studs for Loaded and Unloaded
Conditions, FR 71/72.
a Record the position of the seat studs on the floor at Y+/-280 and Y+/-
840 between Frame 71 and Frame 72.
b Move the seats of the central row between Frame 71 and Frame 72
without removal, refer to Ref. MP A350-A-25-21-46-00ZZZ-520Z-A.
c If any seat stud position is in the loaded area, do a detailed
inspection in accordance with Ref. T ask set A350-A-53-XX-P061-
01ZZZ-93BZ-A.
d If any seat stud position is in the unloaded area, depending on the
operator convenience and the threshold:
- Do a detailed inspection in accordance with Ref. T ask set A350-
A-53-XX-P061-01ZZZ-93BZ-A
OR

### Page 30

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 30
- Do the close-up in accordance with Ref. T ask A350-A-53-XX-
P061-02ZZZ-740Z-A.
NOTE: The threshold value for the loaded and unloaded condition is
different, refer to PLANNING INFORMATION paragraph E.(2)
T able 2.

### Page 31

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05KO8-A-002-01 SHEET 1/2
REV 00 Mar 31/20 A350-53-P061Flowchart, FR 71/72
Page 31
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE
PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
FOR THE ACCOMPLISHMENT TIMESCALE, REFER TO PARAGRAPH 1.E.(2).01
NOTE:
DO A DETAILED INSPECTION OF THE SEAT STUD CONDITION AT FRAMES 71/72
01
ANY SEAT
STUD IS INSTALLED
IN THE LOADED AREA
AT FRAMES 71/72
TRACK Y+/-280?
NO YES
AT THE SEAT STUD LOCATION BETWEEN FRAME 71 AND FRAME 72
DO A DETAILED INSPECTION OF THE ALUMINUM SEAT TRACKS EXTREMITIES
01
ANY SEAT
STUD IS INSTALLED
IN THE LOADED AREA
AT FRAMES 71/72
TRACK Y+/-840?
NO YES
A
ICN-A350-A-53XXP061-A-FAPE3-05KO8-A-002-01

### Page 32

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05KO9-A-003-01 SHEET 2/2
REV 00 Mar 31/20 A350-53-P061Flowchart, FR 71/72
Page 32
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE
PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
FOR THE ACCOMPLISHMENT TIMESCALE, REFER TO PARAGRAPH 1.E.(2).01
NOTE:
APPLY THE PROTECTION OR
IS THE AREA
PROTECTED?YES
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
NO FURTHER ACTION
NO
IS CORROSION
FOUND?NO
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
NO FURTHER ACTION
YES
REMOVE THE CORROSION
MEASURE THE DIMENSIONS OF
THE SEAT RAILS
YES NO
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
NO FURTHER ACTION
DO THE SPLICE REPAIR ACTION
OR
ARE THE
DIMENSIONS WITHIN
THE APPROVED
TOLERANCES?
APPLY THE PROTECTION
APPLY THE PROTECTION
DO NOT GIVE ACCESS TO THE UNSERVICEABLE
ROW OF PASSENGER SEATS UNTIL THE
 CORROSION REMOVAL AND SPLICE REPAIR
A
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
DO NOT GIVE ACCESS TO THE UNSERVICEABLE
ROW OF PASSENGER SEATS UNTIL THE
SPLICE REPAIR
ICN-A350-A-53XXP061-A-FAPE3-05KO9-A-003-01

### Page 33

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05KQA-A-005-01 SHEET 1/1
REV 00 Mar 31/20 A350-53-P061Position of Seat Studs for Loaded and Unloaded Conditions, FR 71/72
Page 33
CONF ALL
LOADED AREA, IF SEAT STUD INSTALLED WITHIN THIS AREA.
01 UNLOADED AREA, IF SEAT STUD INSTALLED WITHIN THIS AREA.
02
Z260
A
F
W
D
-Y280 -Y840+Y280+Y840
CL
FR71
FR72
A
VIEW LOOKING DOWN
SEATS NOT SHOWN
B C
NOTE:
02
BFWD
VIEW LOOKING DOWN
TYPICAL VIEW
C
TYPICAL VIEW
SEAT STUD
TITANIUM SEAT TRACK
ALUMINUM SEAT TRACK
01
END OF SEAT RAIL/COUPLING AREA
SEAT TRACK
FWD25.4 mm(1.0 in)
ICN-A350-A-53XXP061-A-FAPE3-05KQA-A-005-01

### Page 34

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 34
D. PREPARATION FOR TEST
None
E. TEST
(1) Task A350-A-53-XX-P061-02001-320A-A - Test
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Referenced Information
Manuals/Drawings References/Sheets
MP
A350-A-25-21-46-00ZZZ-720Z-A
A350-A-25-21-46-01ZZZ-720Z-A
A350-A-25-21-46-05ZZZ-720Z-A
A350-A-25-21-46-08ZZZ-720Z-A
A350-A-25-21-46-09ZZZ-720Z-A
A350-A-25-21-46-0AZZZ-720Z-A
A350-A-25-21-46-0FZZZ-720Z-A
A350-A-25-21-46-0GZZZ-720Z-A
Procedure
NOTE: If you intend to accomplish the Detailed Inspection of the Seat Tracks
Extremities in accordance with Ref. T ask set A350-A-53-XX-P061-01ZZZ-
93BZ-A during the same layover period, the subsequent T est procedure is not
necessary.
(a) This Service Bulletin requires the accomplishment of T ests given in other topics
which are referenced in the table below:
TASK AMM
Ref. T ask A350-A-53-XX-P061-02ZZZ-740Z-A Ref. MP A350-A-25-21-46-00ZZZ-720Z-A
Ref. T ask A350-A-53-XX-P061-02ZZZ-740Z-A Ref. MP A350-A-25-21-46-00ZZZ-720Z-A or
Ref. MP A350-A-25-21-46-01ZZZ-720Z-A
AND
Ref. MP A350-A-25-21-46-08ZZZ-720Z-A or
Ref. MP A350-A-25-21-46-05ZZZ-720Z-A or
Ref. MP A350-A-25-21-46-09ZZZ-720Z-A or
Ref. MP A350-A-25-21-46-0AZZZ-720Z-A or
Ref. MP A350-A-25-21-46-0FZZZ-720Z-A or
Ref. MP A350-A-25-21-46-0GZZZ-720Z-A
F. CLOSE-UP
(1) Task A350-A-53-XX-P061-02001-740A-A - Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 2.00 h
Minimum Number of person 2

### Page 35

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 35
Elapsed Time 1.00 h
Referenced Information
Manuals/Drawings References/Sheets
MP
A350-A-25-21-46-00ZZZ-720Z-A
A350-A-25-21-46-01ZZZ-720Z-A
A350-A-25-21-46-05ZZZ-720Z-A
A350-A-25-21-46-08ZZZ-720Z-A
A350-A-25-21-46-09ZZZ-720Z-A
A350-A-25-21-46-0AZZZ-720Z-A
A350-A-25-21-46-0FZZZ-720Z-A
A350-A-25-21-46-0GZZZ-720Z-A
Procedure
NOTE: If you intend to accomplish the Detailed Inspection of the Seat Tracks
Extremities in accordance with Ref. T ask set A350-A-53-XX-P061-01ZZZ-93BZ-
A during the same layover period, the subsequent Close-up procedure is not
necessary.
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the seats:
1 Put in its original position and fasten the central row seats between Frame
40 and Frame 41, refer to Ref. MP A350-A-25-21-46-00ZZZ-720Z-A or Ref.
MP A350-A-25-21-46-01ZZZ-720Z-A or Ref. MP A350-A-25-21-46-08ZZZ-
720Z-A or Ref. MP A350-A-25-21-46-05ZZZ-720Z-A or Ref. MP A350-A-25-
21-46-09ZZZ-720Z-A or Ref. MP A350-A-25-21-46-0AZZZ-720Z-A or Ref. MP
A350-A-25-21-46-0FZZZ-720Z-A or Ref. MP A350-A-25-21-46-0GZZZ-720Z-
A.
2 Put in its original position and fasten the central row seats between Frame
71 and Frame 72, refer to Ref. MP A350-A-25-21-46-00ZZZ-720Z-A.
(c) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A350-A-53-XX-P061-03001-90AA-A - Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 36

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 36
Task set A350-A-53-XX-P061-01000-93BA-A
Do a Detailed Inspection of the Seat Tracks Extremities at the Stud Location from Frame 40 to
Frame 41 and from Frame 71 to Frame 72
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESP A350-A-20-55-XX-01ZZZ-
042Z-A.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including RC paragraph contained herein, contact
AIRBUS for further instructions and approval.
NOTE: The purpose of flowcharts is to supplement the information given in the Procedure and
Compliance paragraphs and not to serve as the primary source for tasks or compliance
times given in this Service Bulletin.
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
TOTAL MAN-HOURS 12.50 h

### Page 37

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 37
ELAPSED TIME (HOURS) 10.75 h
B. PREPARATION
(1) Task A350-A-53-XX-P061-01001-540A-A - Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 1.50 h
Minimum Number of person 2
Elapsed Time 0.75 h
Referenced Information
Manuals/Drawings References/Sheets
INTRO A350-A-00-61-04-11ZZZ-018Z-D
MP
A350-A-24-41-XX-00ZZZ-170Z-A
A350-A-25-21-46-00ZZZ-520Z-A
A350-A-25-21-46-01ZZZ-520Z-A
A350-A-25-21-46-05ZZZ-520Z-A
A350-A-25-21-46-08ZZZ-520Z-A
A350-A-25-21-46-09ZZZ-520Z-A
A350-A-25-21-46-0AZZZ-520Z-A
A350-A-25-21-46-0FZZZ-520Z-A
A350-A-25-21-46-0GZZZ-520Z-A
Procedure
NOTE: If the job set-up is already performed given in Ref. T ask set A350-A-53-XX-
P061-02ZZZ-93BZ-A below steps are not applicable.
NOTE: For the basic Aircraft configuration, refer to Ref. INTRO A350-A-00-61-04-
11ZZZ-018Z-D “Maintenance Procedure - Introduction”.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. MP A350-A-24-
41-XX-00ZZZ-170Z-A.
(b) Move the seats of the central row between Frame 40 and Frame 41 FWD without
removal, refer to Ref. MP A350-A-25-21-46-00ZZZ-520Z-A or Ref. MP A350-A-
25-21-46-01ZZZ-520Z-A or Ref. MP A350-A-25-21-46-08ZZZ-520Z-A or Ref. MP
A350-A-25-21-46-05ZZZ-520Z-A or Ref. MP A350-A-25-21-46-09ZZZ-520Z-A or
Ref. MP A350-A-25-21-46-0AZZZ-520Z-A or Ref. MP A350-A-25-21-46-0FZZZ-
520Z-A or Ref. MP A350-A-25-21-46-0GZZZ-520Z-A.
(c) Move the seats of the central row between Frame 71 and Frame 72 FWD without
removal, refer to Ref. MP A350-A-25-21-46-00ZZZ-520Z-A.
C. PROCEDURE
(1) Task A350-A-53-XX-P061-01001-284A-A - Do a Detailed Inspection of the Seat
Tracks Extremities at the Stud Location between Frame 40 and Frame 41 (Y
+/- 280, Y+/-510, and Y+/- 840)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
230 Work location
From Frame 40 to Frame 41
From Y Coord +280mm to Y Coord -280mm
From Y Coord +510mm to Y Coord -510mm

### Page 38

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 38
Impacted Zone Access / Work Location
From Y Coord +840mm to Y Coord -840mm
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Skills Non-Destructive T esting
Referenced Information
Manuals/Drawings References/Sheets
NDT A350-A-51-99-12-00ZZZ-311Z-A
SD A350-A-06-2X-XX-01ZZZ-04CZ-AA350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
2 For the Frame (FR) identification, refer to Ref. SD A350-A-06-2X-XX-01ZZZ-
04CZ-A.
(b) Do a detailed inspection of the aluminum seat tracks extremities at the stud
location between Frame 40 and Frame 41 for the protection and corrosion at the
threshold given in the PLANNING INFORMATION paragraph E.(2) in accordance
with Ref. NDT A350-A-51-99-12-00ZZZ-311Z-A, Ref. Fig. Detailed Inspection of
the Aluminum Seat Tracks Extremities for Protection and Corrosion, FR 40/41 and
Ref. Fig. Flowchart, FR 40/41.
1 If the area is protected:
a Send the inspection report to AIRBUS in accordance with Ref. T ask
A350-A-53-XX-P061-01ZZZ-900Z-A.
b No further action.
2 If the area is not protected:
a Do a visual inspection for the corrosion, refer to Ref. Fig. Detailed
Inspection of the Aluminum Seat Tracks Extremities for Protection and
Corrosion, FR 40/41.
<1> If no corrosion found:
<a> Apply the protection in accordance with Ref. T ask A350-A-
53-XX-P061-01ZZZ-250Z-A.
<b> Send the inspection report to AIRBUS in accordance with
Ref. T ask A350-A-53-XX-P061-01ZZZ-900Z-A.
<c> No further action.
<2> If corrosion found:
<a> Do not give access to the unserviceable central row of
passenger seats until the corrosion removal.
and

### Page 39

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 39
<b> Send the inspection report to AIRBUS in accordance with
Ref. T ask A350-A-53-XX-P061-01ZZZ-900Z-A.
OR
<c> Remove the corrosion in accordance with Ref. T ask A350-
A-53-XX-P061-01ZZZ-650Z-A.
and
<d> Measure the dimensions of the seat rails, refer to Ref. Fig.
Dimensional Check of Aluminum Seat Tracks Extremities,
FR 40/41.
[1] If the dimensions are within the approved
tolerances:
[a] Apply the protection in accordance with Ref.
T ask A350-A-53-XX-P061-01ZZZ-250Z-A.
[b] Send the inspection report to AIRBUS in
accordance with Ref. T ask A350-A-53-XX-P061-
01ZZZ-900Z-A.
[c] No further action.
[2] If the dimensions are not within the approved
tolerances:
[a] Contact AIRBUS for further instructions.

### Page 40

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05G5V-A-005-01 SHEET 1/1
REV 00 Mar 31/20 A350-53-P061Detailed Inspection of the Aluminum Seat Tracks Extremities for Protection and Corrosion, FR 40/41
Page 40
CONF ALL
Z230
A B C D
-Y280+Y280
-Y510
-Y840
+Y510
+Y840
F
W
D
VIEW LOOKING DOWN
01
FR40
FR41
E E
A
CL -Y280-Y510
-Y840
+Y280
+Y510
+Y840
CL
F
W
D
VIEW LOOKING DOWN
01B
FR40
FR41
E E
-Y280+Y280
-Y510
-Y840
+Y510
+Y840
F
W
D
VIEW LOOKING DOWN
01C
FR40
FR41
E E
CL
-Y280+Y280
-Y510
-Y840
+Y510
+Y840 CL
E E
F
W
D
VIEW LOOKING DOWN
01D
FR40
FR41
OR OR
OR
ALUMINUM SEAT TRACK
TITANIUM SEAT TRACK
AREA TO BE INSPECTED
E
DEPENDING ON THE AIRCRAFT CONFIGURATION, SEAT STUD LOCATION CAN DIFFER.01
NOTE:
TYPICAL VIEW
F
W
D
ICN-A350-A-53XXP061-A-FAPE3-05G5V-A-005-01

### Page 41

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05G5T-A-004-01 SHEET 1/2
REV 00 Mar 31/20 A350-53-P061Flowchart, FR 40/41
Page 41
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE
PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
FOR THE ACCOMPLISHMENT TIMESCALE, REFER TO PARAGRAPH 1.E.(2).01
NOTE:
DO A DETAILED INSPECTION OF THE SEAT STUD CONDITION AT FRAMES 40/41
01
ANY SEAT
STUD IS INSTALLED
IN THE LOADED AREA
AT FRAMES 40/41
TRACK Y+/-280?
NO YES
AT THE SEAT STUD LOCATION BETWEEN FRAME 40 AND FRAME 41
DO A DETAILED INSPECTION OF THE ALUMINUM SEAT TRACKS EXTREMITIES
01
ANY SEAT
STUD IS INSTALLED
IN THE LOADED AREA
AT FRAMES 40/41
TRACK Y+/-840?
NO YES
A
ANY SEAT
STUD IS INSTALLED
IN THE LOADED AREA
AT FRAMES 40/41
TRACK Y+/-510?
NO YES
ICN-A350-A-53XXP061-A-FAPE3-05G5T-A-004-01

### Page 42

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05KNP-A-002-01 SHEET 2/2
REV 00 Mar 31/20 A350-53-P061Flowchart, FR 40/41
Page 42
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE
PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
FOR THE ACCOMPLISHMENT TIMESCALE, REFER TO PARAGRAPH 1.E.(2).01
NOTE:
APPLY THE PROTECTION OR
IS THE AREA
PROTECTED?YES
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
NO FURTHER ACTION
NO
IS CORROSION
FOUND?NO
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
NO FURTHER ACTION
YES
REMOVE THE CORROSION
MEASURE THE DIMENSIONS OF
THE SEAT RAILS
YES NO
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
NO FURTHER ACTION
CONTACT AIRBUS FOR FURTHER INSTRUCTIONS
ARE THE
DIMENSIONS WITHIN
THE APPROVED
TOLERANCES?
APPLY THE PROTECTION
DO NOT GIVE ACCESS TO THE UNSERVICEABLE
ROW OF PASSENGER SEATS 
UNTIL THE CORROSION REMOVAL
A
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
ICN-A350-A-53XXP061-A-FAPE3-05KNP-A-002-01

### Page 43

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05G5W-A-005-01 SHEET 1/1
REV 00 Mar 31/20 A350-53-P061Dimensional Check of Aluminum Seat Tracks Extremities, FR 40/41
Page 43
CONF ALL
Z230
A B C D
-Y280+Y280
-Y510
-Y840
+Y510
+Y840
F
W
D
VIEW LOOKING DOWN
01
FR40
FR41
E E
A
CL -Y280-Y510
-Y840
+Y280
+Y510
+Y840
CL
F
W
D
VIEW LOOKING DOWN
01B
FR40
FR41
E E
-Y280+Y280
-Y510
-Y840
+Y510
+Y840
F
W
D
VIEW LOOKING DOWN
01C
FR40
FR41
E E
CL
-Y280+Y280
-Y510
-Y840
+Y510
+Y840 CL
E E
F
W
D
VIEW LOOKING DOWN
01D
FR40
FR41
OR OR
DEPENDING ON THE AIRCRAFT CONFIGURATION, SEAT STUD LOCATION CAN DIFFER.01
AA
MIN DIA 19.7 mm (0.7756 in)
MAX DIA 20 mm (0.7874 in)
E
MIN 10.7 mm (0.422 in)
MAX 11 mm (0.433 in)
MIN 7.8 mm (0.308 in)
MAX 8 mm (0.314 in)
A A
VIEW LOOKING FWD
OR
NOTE:
TYPICAL VIEW
F
W
D
ICN-A350-A-53XXP061-A-FAPE3-05G5W-A-005-01

### Page 44

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 44
(2) Task A350-A-53-XX-P061-01001-650A-A - Remove the Corrosion from the
Seat Tracks Extremities at the Stud Location between Frame 40 and Frame
41 (Y+/- 280, Y+/-510, and Y+/- 840)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
230 Work location
From Frame 40 to Frame 41
From Y Coord +280mm to Y Coord -280mm
From Y Coord +510mm to Y Coord -510mm
From Y Coord +840mm to Y Coord -840mm
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-74-XX-02ZZZ-660Z-A
SD A350-A-06-2X-XX-01ZZZ-04CZ-AA350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
2 For the Frame (FR) identification, refer to Ref. SD A350-A-06-2X-XX-01ZZZ-
04CZ-A.
(b) Remove the corrosion from the aluminum seat tracks extremities at the stud
location between Frame 40 and Frame 41 in accordance with Ref. ASR A350-A-
51-74-XX-02ZZZ-660Z-A.
(3) Task A350-A-53-XX-P061-01001-250A-A - Apply the Protection to the Seat
Tracks Extremities at the Stud Location between Frame 40 and Frame 41 (Y
+/- 280, Y+/-510, and Y+/- 840)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
230 Work location
From Frame 40 to Frame 41
From Y Coord +280mm to Y Coord -280mm
From Y Coord +510mm to Y Coord -510mm
From Y Coord +840mm to Y Coord -840mm
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

### Page 45

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 45
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-75-12-02ZZZ-660Z-A
SD A350-A-06-2X-XX-01ZZZ-04CZ-AA350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
2 For the Frame (FR) identification, refer to Ref. SD A350-A-06-2X-XX-01ZZZ-
04CZ-A.
(b) Apply the protection to the aluminum seat tracks extremities at the stud location
between Frame 40 and Frame 41 in accordance with Ref. ASR A350-A-51-75-12-
02ZZZ-660Z-A.
(4) Task A350-A-53-XX-P061-02001-284A-A - Do a Detailed Inspection of the Seat
Tracks Extremities at the Stud Location between Frame 71 and Frame 72 (Y
+/- 280 and Y+/- 840)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
260 Work location
From Frame 71 to Frame 72
From Y Coord +280mm to Y Coord -280mm
From Y Coord +840mm to Y Coord -840mm
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Skills Non-Destructive T esting
Referenced Information
Manuals/Drawings References/Sheets
NDT A350-A-51-99-12-00ZZZ-311Z-A
SD A350-A-06-2X-XX-01ZZZ-04CZ-AA350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
2 For the Frame (FR) identification, refer to Ref. SD A350-A-06-2X-XX-01ZZZ-
04CZ-A.
(b) Do a detailed inspection of the aluminum seat tracks extremities at the stud
location between Frame 71 and Frame 72 for the protection and corrosion at the
threshold given in the PLANNING INFORMATION paragraph E.(2) in accordance
with Ref. NDT A350-A-51-99-12-00ZZZ-311Z-A, Ref. Fig. Detailed Inspection of

### Page 46

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 46
the Aluminum Seat Tracks Extremities for Protection and Corrosion, FR 71/72 and
Ref. Fig. Flowchart, FR 71/72.
1 If the area is protected:
a Send the inspection report to AIRBUS in accordance with Ref. T ask
A350-A-53-XX-P061-02ZZZ-900Z-A.
b No further action.
2 If the area is not protected:
a Do a visual inspection for the corrosion, refer to Ref. Fig. Detailed
Inspection of the Aluminum Seat Tracks Extremities for Protection and
Corrosion, FR 71/72.
<1> If no corrosion found:
<a> Apply the protection in accordance with Ref. T ask A350-A-
53-XX-P061-02ZZZ-250Z-A.
<b> Send the inspection report to AIRBUS in accordance with
Ref. T ask A350-A-53-XX-P061-02ZZZ-900Z-A.
<c> No further action.
<2> If corrosion found:
<a> Do not give access to the unserviceable central row of
passenger seats until the corrosion removal and splice
repair.
and
<b> Send the inspection report to AIRBUS in accordance with
Ref. T ask A350-A-53-XX-P061-02ZZZ-900Z-A.
OR
<c> Remove the corrosion in accordance with Ref. T ask A350-
A-53-XX-P061-02ZZZ-650Z-A.
and
<d> Measure the dimensions of the seat rails, refer to Ref. Fig.
Dimensional Check of Aluminum Seat Tracks Extremities,
FR 71/72.
[1] If the dimensions are within the approved
tolerances:
[a] Apply the protection in accordance with Ref.
T ask A350-A-53-XX-P061-02ZZZ-250Z-A.
[b] Send the inspection report to AIRBUS in
accordance with Ref. T ask A350-A-53-XX-P061-
02ZZZ-900Z-A.
[c] No further action.
[2] If the dimensions are not within the approved
tolerances:
[a] Apply the protection in accordance with Ref.
T ask A350-A-53-XX-P061-02ZZZ-250Z-A.
and
[b] Do not give access to the unserviceable
central row of passenger seats until the splice
repair.

### Page 47

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 47
[c] Send the inspection report to AIRBUS in
accordance with Ref. T ask A350-A-53-XX-P061-
02ZZZ-900Z-A.
OR
[d] Do the splice repair in accordance with Ref.
T ask A350-A-53-XX-P061-01ZZZ-690Z-A.
and
[e] Send the inspection report to AIRBUS in
accordance with Ref. T ask A350-A-53-XX-P061-
02ZZZ-900Z-A.
[f] No further action.

### Page 48

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05KO3-A-003-01 SHEET 1/1
REV 00 Mar 31/20 A350-53-P061Detailed Inspection of the Aluminum Seat Tracks Extremities for Protection and Corrosion, FR 71/72
Page 48
CONF ALL
ALUMINUM SEAT TRACK
TITANIUM SEAT TRACK
AREA TO BE INSPECTED
DEPENDING ON THE AIRCRAFT CONFIGURATION, SEAT STUD LOCATION CAN DIFFER.01
Z260
A B C
A
F
W
D
VIEW LOOKING DOWN
01
-Y280 -Y840+Y280+Y840
FR71
FR72
CL
D
F
W
D
VIEW LOOKING DOWN
B 01
-Y280 -Y840+Y280+Y840
CL
D
F
W
D
VIEW LOOKING DOWN
01C
-Y280 -Y840+Y280+Y840
CL
D
OR
D
FR71
FR72
FR71
FR72
OR
NOTE:
TYPICAL VIEW
F
W
D
ICN-A350-A-53XXP061-A-FAPE3-05KO3-A-003-01

### Page 49

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05KO8-A-002-01 SHEET 1/2
REV 00 Mar 31/20 A350-53-P061Flowchart, FR 71/72
Page 49
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE
PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
FOR THE ACCOMPLISHMENT TIMESCALE, REFER TO PARAGRAPH 1.E.(2).01
NOTE:
DO A DETAILED INSPECTION OF THE SEAT STUD CONDITION AT FRAMES 71/72
01
ANY SEAT
STUD IS INSTALLED
IN THE LOADED AREA
AT FRAMES 71/72
TRACK Y+/-280?
NO YES
AT THE SEAT STUD LOCATION BETWEEN FRAME 71 AND FRAME 72
DO A DETAILED INSPECTION OF THE ALUMINUM SEAT TRACKS EXTREMITIES
01
ANY SEAT
STUD IS INSTALLED
IN THE LOADED AREA
AT FRAMES 71/72
TRACK Y+/-840?
NO YES
A
ICN-A350-A-53XXP061-A-FAPE3-05KO8-A-002-01

### Page 50

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05KO9-A-003-01 SHEET 2/2
REV 00 Mar 31/20 A350-53-P061Flowchart, FR 71/72
Page 50
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE
PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
FOR THE ACCOMPLISHMENT TIMESCALE, REFER TO PARAGRAPH 1.E.(2).01
NOTE:
APPLY THE PROTECTION OR
IS THE AREA
PROTECTED?YES
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
NO FURTHER ACTION
NO
IS CORROSION
FOUND?NO
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
NO FURTHER ACTION
YES
REMOVE THE CORROSION
MEASURE THE DIMENSIONS OF
THE SEAT RAILS
YES NO
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
NO FURTHER ACTION
DO THE SPLICE REPAIR ACTION
OR
ARE THE
DIMENSIONS WITHIN
THE APPROVED
TOLERANCES?
APPLY THE PROTECTION
APPLY THE PROTECTION
DO NOT GIVE ACCESS TO THE UNSERVICEABLE
ROW OF PASSENGER SEATS UNTIL THE
 CORROSION REMOVAL AND SPLICE REPAIR
A
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
REPORT SHEET TO AIRBUS
SEND THE COMPLETED INSPECTION
01
DO NOT GIVE ACCESS TO THE UNSERVICEABLE
ROW OF PASSENGER SEATS UNTIL THE
SPLICE REPAIR
ICN-A350-A-53XXP061-A-FAPE3-05KO9-A-003-01

### Page 51

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05KNS-A-003-01 SHEET 1/1
REV 00 Mar 31/20 A350-53-P061Dimensional Check of Aluminum Seat Tracks Extremities, FR 71/72
Page 51
CONF ALL
DEPENDING ON THE AIRCRAFT CONFIGURATION, SEAT STUD LOCATION CAN DIFFER.01
Z260
A B C
A
F
W
D
VIEW LOOKING DOWN
01
-Y280 -Y840+Y280+Y840
FR71
FR72
CL
D
F
W
D
VIEW LOOKING DOWN
B 01
-Y280 -Y840+Y280+Y840
CL
D
F
W
D
VIEW LOOKING DOWN
01C
-Y280 -Y840+Y280+Y840
CL
D
OR
AA
MIN DIA 19.7 mm (0.7756 in)
MAX DIA 20 mm (0.7874 in)
D
MIN 10.7 mm (0.422 in)
MAX 11 mm (0.433 in)
MIN 7.8 mm (0.308 in)
MAX 8 mm (0.314 in)
A A
VIEW LOOKING FWD
FR71
FR72
FR71
FR72
OR
TYPICAL VIEW
F
W
D
NOTE:
ICN-A350-A-53XXP061-A-FAPE3-05KNS-A-003-01

### Page 52

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 52
(5) Task A350-A-53-XX-P061-02001-650A-A - Remove the Corrosion from the
Seat Tracks Extremities at the Stud Location between Frame 71 and Frame
72 (Y+/- 280 and Y+/- 840)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
260 Work location
From Frame 71 to Frame 72
From Y Coord +280mm to Y Coord -280mm
From Y Coord +840mm to Y Coord -840mm
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-74-XX-02ZZZ-660Z-A
SD A350-A-06-2X-XX-01ZZZ-04CZ-AA350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
2 For the Frame (FR) identification, refer to Ref. SD A350-A-06-2X-XX-01ZZZ-
04CZ-A.
(b) Remove the corrosion from the aluminum seat tracks extremities at the stud
location between Frame 71 and Frame 72 in accordance with Ref. ASR A350-A-
51-74-XX-02ZZZ-660Z-A.
(6) Task A350-A-53-XX-P061-02001-250A-A - Apply the Protection to the Seat
Tracks Extremities at the Stud Location between Frame 71 and Frame 72 (Y
+/- 280 and Y+/- 840)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
260 Work location
From Frame 71 to Frame 72
From Y Coord +280mm to Y Coord -280mm
From Y Coord +840mm to Y Coord -840mm
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

### Page 53

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 53
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-75-12-02ZZZ-660Z-A
SD A350-A-06-2X-XX-01ZZZ-04CZ-AA350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
2 For the Frame (FR) identification, refer to Ref. SD A350-A-06-2X-XX-01ZZZ-
04CZ-A.
(b) Apply the protection to the aluminum seat tracks extremities at the stud location
between Frame 71 and Frame 72 in accordance with Ref. ASR A350-A-51-75-12-
02ZZZ-660Z-A.
(7) Task A350-A-53-XX-P061-01001-690A-A - Do the Splice Repair on the Seat
Tracks Extremities at the Stud Location between Frame 71 and Frame 72 (Y
+/- 280 and Y+/- 840)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
260 Work location
From Frame 71 to Frame 72
From Y Coord +280mm to Y Coord -280mm
From Y Coord +840mm to Y Coord -840mm
Manpower/Resources/Skills
Man-hours 4.00 h
Minimum Number of person 1
Elapsed Time 4.00 h
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-53-41-86-00ZZZ-664Z-A
SD A350-A-06-2X-XX-01ZZZ-04CZ-AA350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
2 For the Frame (FR) identification, refer to Ref. SD A350-A-06-2X-XX-01ZZZ-
04CZ-A.

### Page 54

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 54
(b) Do the splice repair on the aluminum seat tracks extremities at the stud location
between Frame 71 and Frame 72 in accordance with Ref. ASR A350-A-53-41-86-
00ZZZ-664Z-A.
D. PREPARATION FOR TEST
None
E. TEST
(1) Task A350-A-53-XX-P061-01001-320A-A - Test
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Referenced Information
Manuals/Drawings References/Sheets
MP
A350-A-25-21-46-00ZZZ-720Z-A
A350-A-25-21-46-01ZZZ-720Z-A
A350-A-25-21-46-05ZZZ-720Z-A
A350-A-25-21-46-08ZZZ-720Z-A
A350-A-25-21-46-09ZZZ-720Z-A
A350-A-25-21-46-0AZZZ-720Z-A
A350-A-25-21-46-0FZZZ-720Z-A
A350-A-25-21-46-0GZZZ-720Z-A
Procedure
(a) This Service Bulletin requires the accomplishment of T ests given in other topics
which are referenced in the table below:
TASK AMM
Ref. T ask A350-A-53-XX-P061-01ZZZ-740Z-A Ref. MP A350-A-25-21-46-00ZZZ-720Z-A
Ref. T ask A350-A-53-XX-P061-01ZZZ-740Z-A Ref. MP A350-A-25-21-46-00ZZZ-720Z-A or
Ref. MP A350-A-25-21-46-01ZZZ-720Z-A
AND
Ref. MP A350-A-25-21-46-08ZZZ-720Z-A or
Ref. MP A350-A-25-21-46-05ZZZ-720Z-A or
Ref. MP A350-A-25-21-46-09ZZZ-720Z-A or
Ref. MP A350-A-25-21-46-0AZZZ-720Z-A or
Ref. MP A350-A-25-21-46-0FZZZ-720Z-A or
Ref. MP A350-A-25-21-46-0GZZZ-720Z-A
F. CLOSE-UP
(1) Task A350-A-53-XX-P061-01001-740A-A - Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 2.00 h
Minimum Number of person 2
Elapsed Time 1.00 h

### Page 55

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 55
Referenced Information
Manuals/Drawings References/Sheets
MP
A350-A-25-21-46-00ZZZ-720Z-A
A350-A-25-21-46-01ZZZ-720Z-A
A350-A-25-21-46-05ZZZ-720Z-A
A350-A-25-21-46-08ZZZ-720Z-A
A350-A-25-21-46-09ZZZ-720Z-A
A350-A-25-21-46-0AZZZ-720Z-A
A350-A-25-21-46-0FZZZ-720Z-A
A350-A-25-21-46-0GZZZ-720Z-A
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the seats:
NOTE: Below work step is not applicable, if the area is unserviceable after the
inspection.
1 Put in its original position and fasten the central row seats between Frame
40 and Frame 41, refer to Ref. MP A350-A-25-21-46-00ZZZ-720Z-A or Ref.
MP A350-A-25-21-46-01ZZZ-720Z-A or Ref. MP A350-A-25-21-46-08ZZZ-
720Z-A or Ref. MP A350-A-25-21-46-05ZZZ-720Z-A or Ref. MP A350-A-25-
21-46-09ZZZ-720Z-A or Ref. MP A350-A-25-21-46-0AZZZ-720Z-A or Ref. MP
A350-A-25-21-46-0FZZZ-720Z-A or Ref. MP A350-A-25-21-46-0GZZZ-720Z-
A.
2 Put in its original position and fasten the central row seats between Frame
71 and Frame 72, refer to Ref. MP A350-A-25-21-46-00ZZZ-720Z-A.
(c) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A350-A-53-XX-P061-01001-90AA-A - Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 56

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 56
Task set A350-A-53-XX-P061-01000-93EA-A
Reporting of the Inspection Results to AIRBUS
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESP A350-A-20-55-XX-01ZZZ-
042Z-A.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including RC paragraph contained herein, contact
AIRBUS for further instructions and approval.
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
TOTAL MAN-HOURS 0.50 h
ELAPSED TIME (HOURS) 0.50 h
B. PREPARATION
None

### Page 57

A350
SERVICE BULLETIN
REV 00 Mar 31/20 A350-53-P061
Page 57
C. PROCEDURE
(1) Task A350-A-53-XX-P061-01001-900A-A - Report to AIRBUS after the Detailed
Inspection between Frame 40 and Frame 41 (Y+/- 280, Y+/-510, and Y+/-
840)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
230 Work location
From Frame 40 to Frame 41
From Y Coord +280mm to Y Coord -280mm
From Y Coord +510mm to Y Coord -510mm
From Y Coord +840mm to Y Coord -840mm
Manpower/Resources/Skills
Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Procedure
(a) Report the findings of aluminum seat tracks extremities to AIRBUS at the
threshold given in the PLANNING INFORMATION paragraph E.(2).
1 Complete the inspection report sheet, refer to Ref. Fig. Inspection Report,
FR 40/41.
2 Send the completed inspection report sheet in accordance with Ref. ISI
00.00.00179.

### Page 58

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05G5R-A-005-01 SHEET 1/3
REV 00 Mar 31/20 A350-53-P061Inspection Report, FR 40/41
Page 58
CONF ALL
INSPECTION REPORT
SERVICE BULLETIN No : 
A/C MSN :
FLIGHT CYCLES :
FLIGHT HOURS :
A350-53-P061
DATE OF INSPECTION :
INSPECTION METHOD : DETAILED
INSPECTION
SHEET IN ACCORDANCE WITH ISI 00.00.00179
SEND THE COMPLETED INSPECTION REPORT
DEPENDING ON THE AIRCRAFT CONFIGURATION, SEAT STUD LOCATION CAN DIFFER.01
ALUMINUM SEAT TRACK
TITANIUM SEAT TRACK
C
Z230
A B
F
W
D
VIEW LOOKING DOWN
01
FR40
FR41
+Y280
+Y510
+Y840
-Y280
-Y510
-Y840
A
C C
CL
OR
F
W
D
VIEW LOOKING DOWN
01
+Y280
+Y510
+Y840
-Y280
-Y510
-Y840CL
FR40
FR41
B
C C
D
NOTE:
TYPICAL VIEW
F
W
D
ICN-A350-A-53XXP061-A-FAPE3-05G5R-A-005-01

### Page 59

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05G5S-A-004-01 SHEET 2/3
REV 00 Mar 31/20 A350-53-P061Inspection Report, FR 40/41
Page 59
CONF ALL
A A
MIN DIA 19.7 mm (0.7756 in)
MAX DIA 20 mm (0.7874 in)
MIN 7.8 mm (0.308 in)
MAX 8 mm (0.314 in)
MIN 10.7 mm (0.422 in)
MAX 11 mm (0.433 in)
A A
VIEW LOOKING FWD
INSPECTION REPORT
SERVICE BULLETIN No : 
A/C MSN :
FLIGHT CYCLES :
FLIGHT HOURS :
A350-53-P061
DATE OF INSPECTION :
INSPECTION METHOD : DETAILED
INSPECTION
SHEET IN ACCORDANCE WITH ISI 00.00.00179
SEND THE COMPLETED INSPECTION REPORT
D
F
W
D
ICN-A350-A-53XXP061-A-FAPE3-05G5S-A-004-01

### Page 60

A350
SERVICE BULLETIN
Figure ICN-A350-A-53XXP061-A-FAPE3-05KNO-A-002-01 SHEET 3/3
REV 00 Mar 31/20 A350-53-P061Inspection Report, FR 40/41
Page 60
CONF ALL
INSPECTION REPORT
SERVICE BULLETIN No : 
A/C MSN :
FLIGHT CYCLES :
FLIGHT HOURS :
A350-53-P061
DATE OF INSPECTION :
INSPECTION METHOD : DETAILED
INSPECTION
SHEET IN ACCORDANCE WITH ISI 00.00.00179
SEND THE COMPLETED INSPECTION REPORT
ADDITIONAL COMMENTS:
ARE THE NEW DIMENSIONS WITHIN THE
TOLERANCE AS PER VIEW C AND SECTION A-A?
IS THE AREA PROTECTED?
IS THE CORROSION FOUND?
IS THE CORROSION REMOVED?
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
IS THE AREA BLOCKED UNTIL CORROSION REMOVAL?
ICN-A350-A-53XXP061-A-FAPE3-05KNO-A-002-01

The text continues at https://openairdocs.org/service-documents/airbus/a350-53-p061/file/385186c6ff03.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
