# Airbus Service Bulletin A350-57-P011

Copy: No revision named ("SB A350-57-P011"), 54 pages: PDF https://openairdocs.org/files/sha256/7f/fd/7ffdd2916ed1db82db816406df521e329a01962304310d23a3d5d4729fed3bc3; text https://openairdocs.org/service-documents/airbus/a350-57-p011/file/7ffdd2916ed1.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2018-0490; AD 2018-11-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A350-57-P011
- Page: https://openairdocs.org/service-documents/airbus/a350-57-p011

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2018-11-11](https://openairdocs.org/ad/2018-11-11.md), effective Jun 20, 2018: No revision named

## Text (54 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2018-0490; AD 2018-11-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

@A350
SERVICE BULLETIN
SUMMARY
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
This summary is for information only and is not approved for modification of the aircraft.
MANDATORY
 MANDATORY
 MANDATORY
ATA SYSTEM: 57
TITLE: WINGS - FITTINGS - INSPECTION OF RETAINING PIN INSTALLATION
AT THE TRUNNION BLOCK FUSE PINS
**CONF ALL
MODIFICATIONS
None
REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
An A350 aircraft has a total of six retaining pins (one per fuse pin) installed on the Main Landing Gear
Support Structure (MLGSS) forward pintle. The retaining pins are to prevent rotation and migration of
the fuse pins; two shorter pins are installed through the fuse pin carrier and four longer pins are
installed through the trunnion block. It has been identified in production that the shorter pins may have
inadvertently been installed at the incorrect location which may lead to fuse pin migration.
This Service Bulletin is published to advise A350 operators a one-time Detailed Inspection (DET) on the
four retaining pins installed at the MLGSS trunnion block.
Accomplishment of this Service Bulletin will ensure correct installation of the retaining pins in the
MLGSS trunnion block fuse pins.
GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE
 MANDATORY (1)
 CANCELS INSPECTION SB
 NO
POTENTIAL AD
 YES
 A/C OPERATION AFFECTED
 NO
RELIABILITY AFFECTED
 NO
 PAX COMFORT AFFECTED
 NO
COST SAVING
 NO
 ETOPS AFFECTED
 NO
STRUCTURAL LIFE EXTN
 NO
 VENDOR SB INVOLVED
 NO
NOTE
 (1)
: Service Bulletin must be accomplished.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 2

@A350
SERVICE BULLETIN
SUMMARY
MATERIAL PRICE INFORMATION
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET
 QTY PER
A/C
PRICE PER
A/C (USD)
MAIN PARTS
Component COMPB01
 1
 See SB
 Retaining pins
Component COMPB02
 1
 See SB
 Cotter pins, nuts
EFFECTIVITY
This Service Bulletin is applicable to this (these) operator(s) :
CPA ETH FIN HVN QTR SIA TAM
CONCURRENT REQUIREMENTS
None
REFERENCES / REPERCUSSIONS
TFU
 None
OEB
 None
AOT
 None
SIL
 None
ISI
 None
LINE MAINTENANCE AFFECTED
 No
LIFE LIMIT
 None
OTHER
 None
NATURE OF THE WORK
AIRCRAFT
 YES
EQUIPMENT
 NO
HARD
 NO
SOFT
 NO
OBRM
 NO
MANPOWER
Task 57P011-832-895-001: Inspection
TOTAL MANHOURS
 5.50
ELAPSED TIME (HOURS)
 2.75
Task 57P011-833-895-001: Replacement of the Non-conforming Retaining Pins installed in the
MLGSS Trunnion Block with Aircraft on Wheels
TOTAL MANHOURS
 9.00
ELAPSED TIME (HOURS)
 4.50
Task 57P011-833-896-001: Replacement of the Non-conforming Retaining Pins installed in the
MLGSS Trunnion Block with Aircraft on Jacks
TOTAL MANHOURS
 16.00
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 2
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 3

@A350
SERVICE BULLETIN
SUMMARY
Task 57P011-833-896-001: Replacement of the Non-conforming Retaining Pins installed in the
MLGSS Trunnion Block with Aircraft on Jacks
ELAPSED TIME (HOURS)
 4.50
APPENDICES
Appendix 01 - Manpower Gantt Chart
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 3
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 4

@A350
SERVICE BULLETIN
SUMMARY
**CONF ALL
B
B
LH SHOWN
RH SYMMETRICAL
A
REAR SPAR
MAIN LANDING
GEAR
GEAR BEAM
RIB3
RIB5
REAR SPAR
INSPECTION OF THE FOUR
RETAINING PINS IN THE 
TRUNNION BLOCK
A
Z571
Z671
LH
RH
TRUNNION
BLOCK
FUSE PIN
CARRIER
01
UPPER AND LOWER TENSION STRAPS REMOVED FOR CLARITY.01
NOTE:
P_SB_57P011_7_SAAA_01_01
Figure A-USAAA - Sheet 01
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 4
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 5

@A350
SERVICE BULLETIN
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
MANDATORY
 MANDATORY
 MANDATORY
ATA SYSTEM: 57
TITLE: WINGS - FITTINGS - INSPECTION OF RETAINING PIN INSTALLATION
AT THE TRUNNION BLOCK FUSE PINS
MODIFICATION No.: None
This document contains AIRBUS PROPRIETARY INFORMATION and shall at all times remain the
property of AIRBUS; no intellectual property right or licence is granted by AIRBUS in connection with
any information contained in it. It is delivered on the express condition that said document and the
information contained in it shall be treated as confidential, shall not be used for any purpose other than
that for which it is hereby delivered. It shall not be disclosed in whole or in part to third parties and shall
not be duplicated in any manner (except for the purposes of performing the tasks described hereunder
and provided that any recipient of such document shall comply with the conditions herein), without
AIRBUS prior written consent.
1. PLANNING INFORMATION
**CONF ALL
A. EFFECTIVITY
(1) Models
350-941
(2) Effectivity by MSN
0006-0024 0026-0031 0034-0035 0037 0040
(3) Effectivity by Operator
The Operator/MSN relationship is provided for information only and is correct at the time
of issue in accordance with the information available to AIRBUS. Any future changes
resulting from transfer of an aircraft from one operator to another will not be reflected in
this list unless the Service Bulletin is revised for another reason.
OPERATOR
 MSN
CPA
 0029 0034
ETH
 0040
FIN
 0018 0019 0020 0022 0023 0028
HVN
 0014 0015 0016 0017
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 6

@A350
SERVICE BULLETIN
OPERATOR
 MSN
QTR
 0006 0007 0008 0009 0010 0011 0012 0013 0021
SIA
 0026 0030 0031 0037
TAM
 0024 0027 0035
(4) Configuration by MSN
MSN
 CONFIGURATION
0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016
0017 0018 0019 0020 0021 0022 0023 0024 0026 0027 0028
0029 0030 0031 0034 0035 0037 0040
001
(5) Configuration definition
**CONF 001
Config. 001 is valid for all the aircraft given in the effectivity of this Service Bulletin as a
standard configuration.
(6) Material Effectivity
MATERIAL
 QTY PER A/C
 SEE NOTES
Component COMPB01
 1
Component COMPB02
 1
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
An A350 aircraft has a total of six retaining pins (one per fuse pin) installed on the Main
Landing Gear Support Structure (MLGSS) forward pintle. The retaining pins are to
prevent rotation and migration of the fuse pins; two shorter pins are installed through the
fuse pin carrier and four longer pins are installed through the trunnion block. It has been
identified in production that the shorter pins may have inadvertently been installed at the
incorrect location which may lead to fuse pin migration.
(2) Objective/Action
This Service Bulletin is published to advise A350 operators a one-time Detailed
Inspection (DET) on the four retaining pins installed at the MLGSS trunnion block.
(3) Advantages
Accomplishment of this Service Bulletin will ensure correct installation of the retaining
pins in the MLGSS trunnion block fuse pins.
(4) Operational/Maintenance Consequences
None
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 2
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 7

@A350
SERVICE BULLETIN
D. DESCRIPTION
To accomplish this Service Bulletin it is necessary to :
Task 57P011-832-895-001: Inspection
(1) Do a DET of the Four Retaining Pins installed in the MLGSS Trunnion Block, LH
Side
(2) Do a DET of the Four Retaining Pins installed in the MLGSS Trunnion Block, RH
Side
Task 57P011-833-895-001: Replacement of the Non-conforming Retaining Pins installed in
the MLGSS Trunnion Block with Aircraft on Wheels
(1) Replace the Non-conforming Retaining Pins installed in the MLGSS Trunnion Block
with Aircraft on Wheels, LH Side
(2) Replace the Non-conforming Retaining Pins installed in the MLGSS Trunnion Block
with Aircraft on Wheels, RH Side
Task 57P011-833-896-001: Replacement of the Non-conforming Retaining Pins installed in
the MLGSS Trunnion Block with Aircraft on Jacks
(1) Replace the Non-conforming Retaining Pins installed in the MLGSS Trunnion Block
with Aircraft on Jacks, LH Side
(2) Replace the Non-conforming Retaining Pins installed in the MLGSS Trunnion Block
with Aircraft on Jacks, RH Side
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
This Service Bulletin has been classified Mandatory. It is expected that an Airworthiness
Directive (AD) published by the European Av iation Safety Agenc y (EASA) will be issued
to confirm this classification. It is anticipated that the AD will confirm the threshold
given but reference should be made to the AD for confirmation of the mandated
accomplishment timescale.
Accomplishment of this Service Bulletin must be done as per the below table.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 3
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 8

@A350
SERVICE BULLETIN
Table 01, Config. 001 - Do a DET of the four retaining pins installed in the MLGSS trunnion block
COMPLIANCE TIME
CONDITION
 ACTION
 THRESHOLD
 GRACE PERIOD
REPETITIVE
INTERVAL
All aircraft
 In accordance with
SUBTASK
57P011-220-401 001
Do a DET of the Four
Retaining Pins installed
in the MLGSS Trunnion
Block, LH Side and
SUBTASK
57P011-220-402 001
Do a DET of the Four
Retaining Pins installed
in the MLGSS Trunnion
Block, RH Side
1880 Flight
Cycles (FC) from
the first flight
None
 None
If the incorrect
retaining pins are
installed
Examine the retaining
pins for damage or
deformation
None
 None
 None
If damage or
deformation is
found on the
retaining pins
Contact AIRBUS before
next flight and follow
their instructions
None
 None
 None
If no damage or
deformation is
found on the
retaining pins
Replace the non-
conforming retaining
pins
None
 None
 None
If replacement of
the non-conforming
retaining pins is
possible with
aircraft on wheels
In accordance with
SUBTASK
57P011-960-401 001
Replace the Non-
conforming Retaining
Pins installed in the
MLGSS Trunnion Block
with Aircraft on Wheels,
LH Side and SUBTASK
57P011-960-402 001
Replace the Non-
conforming Retaining
Pins installed in the
MLGSS Trunnion Block
with Aircraft on Wheels,
RH Side
1880 FC from the
first flight
None
 None
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 4
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 9

@A350
SERVICE BULLETIN
Table 01, Config. 001 - Do a DET of the four retaining pins installed in the MLGSS trunnion block
COMPLIANCE TIME
CONDITION
 ACTION
 THRESHOLD
 GRACE PERIOD
REPETITIVE
INTERVAL
If replacement of
the non-conforming
retaining pins is
not possible with
aircraft on wheels
In accordance with
SUBTASK
57P011-960-405 001
Replace the Non-
conforming Retaining
Pins installed in the
MLGSS Trunnion Block
with Aircraft on Jacks,
LH Side and SUBTASK
57P011-960-406 001
Replace the Non-
conforming Retaining
Pins installed in the
MLGSS Trunnion Block
with Aircraft on Jacks,
RH Side
1880 FC from the
first flight
None
 None
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the effectivity has a modification or repair embodied that is not of
AIRBUS origin, and which affects the content of this Service Bulletin, the operator is
responsible for obtaining approval by its airworthiness authority for any adaptation necessary
before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also not
included.
Task 57P011-832-895-001: Inspection
Get Access
 2.50
On Aircraft
Do a DET of the Four Retaining Pins installed in the
MLGSS Trunnion Block, LH Side
0.25
Do a DET of the Four Retaining Pins installed in the
MLGSS Trunnion Block, RH Side
0.25
Close-Up
 2.50
TOTAL MANHOURS
 5.50
ELAPSED TIME (HOURS)
 2.75
NOTE
: For an explanation of the manhours and elapsed time, refer to the Gantt
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 5
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 10

@A350
SERVICE BULLETIN
Chart, Fig. A-UAAAA
 given in Appendix 01 - Manpower Gantt Chart .
Task 57P011-833-895-001: Replacement of the Non-conforming Retaining Pins installed in the
MLGSS Trunnion Block with Aircraft on Wheels
Get Access
 2.50
On Aircraft
Replace the Non-conforming Retaining Pins installed in
the MLGSS Trunnion Block with Aircraft on Wheels, LH
Side
2.00
Replace the Non-conforming Retaining Pins installed in
the MLGSS Trunnion Block with Aircraft on Wheels,
RH Side
2.00
Close-Up
 2.50
TOTAL MANHOURS
 9.00
ELAPSED TIME (HOURS)
 4.50
NOTE
: The minimum manhours necessary to accomplish this Service Bulletin are
those for the Inspection. Depending on the inspection result, additional
manhours can apply.
Task 57P011-833-896-001: Replacement of the Non-conforming Retaining Pins installed in the
MLGSS Trunnion Block with Aircraft on Jacks
Get Access
 6.00
On Aircraft
Replace the Non-conforming Retaining Pins installed in
the MLGSS Trunnion Block with Aircraft on Jacks, LH
Side
2.00
Replace the Non-conforming Retaining Pins installed in
the MLGSS Trunnion Block with Aircraft on Jacks, RH
Side
2.00
Close-Up
 6.00
TOTAL MANHOURS
 16.00
ELAPSED TIME (HOURS)
 4.50
NOTE
: The minimum manhours necessary to accomplish this Service Bulletin are
those for the Inspection. Depending on the inspection result, additional
manhours can apply.
H. WEIGHT AND BALANCE
Not Changed
I. ELECTRICAL LOAD DATA
Not Changed
J. REFERENCES
Aircraft Structural Repair (ASR)
 51-42-XX
Electrical Standard Practices (ESP)
 20-55-XX
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 6
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 11

@A350
SERVICE BULLETIN
Maintenance Procedure (MP)
 07-11-XX 20-51-50 24-41-XX
32-12-XX 57-51-71
System Description (SD)
 06-3X-XX 06-4X-XX
Standards Manual (SM)
K. PUBLICATION AFFECTED
None
L. INTERCHANGEABILITY/MIXABILITY
Not Applicable
M. SPARES
None
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 7
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 12

@A350
SERVICE BULLETIN
This Page Intentionally Left Blank
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 8
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 13

@A350
SERVICE BULLETIN
2. MATERIAL INFORMATION
**CONF ALL
A. MATERIAL - PRICE AND AVAILABILITY
(1) Procurement Addresses
Customers with aircraft shown in the effectivity of this Service Bulletin should send a
purchase order to AIRBUS. Quote the number of this Service Bulletin. The address is:
Component COMPB01
 AIRBUS Material, Logistics and Suppliers
IFD - In Flight Desk
Weg beim Jaeger 150
D-22335 HAMBURG
GERMANY
For ordering by internet:
http://spares.airbus.com
For ordering by fax: +49 40 50 76 4012
For ordering by E-mail:
ifd.spares@airbus.com
For standard hardware the purchase order shall be addressed to AIRBUS. Quote the
number of this Service Bulletin, the MSN and, if applicable the Retrofit Information Letter
(RIL) reference. Please send your request to:
Component COMPB02
 AIRBUS Material, Logistic and Suppliers
Standard Parts
For ordering by internet:
http://spares.airbus.com or vi a SPEC2000
For ordering by E-mail:
standard.parts@airbus.com
Phone: +49 (0) 40 50 76 40 03
(2) Price and Availability
Component COMPB01
Operator supplied AIRBUS parts required to accomplish this Service Bulletin are to be
purchased by a spares purchase order.
Component COMPB02
Operator supplied standard hardware parts, required to accomplish this Service Bulletin,
are to be supplied from the operator’s stock.
B. INDUSTRY SUPPORT INFORMATION
For those aircraft in warranty at the time of such inspection with findings further to inspection
as per this Service Bulletin, AIRBUS will share the costs of accomplishment of this Service
Bulletin by crediting the operator supplied AIRBUS parts for orders placed before Apr 30/19.
Claims for this allowance should be received no later than 90 days after completion of the
last affected aircraft of your fleet.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 9
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 14

@A350
SERVICE BULLETIN
For the accomplishment of this Service Bulletin before Apr 30/19, AIRBUS will share the
costs by crediting the operator supplied standard hardware parts. Claims for this allowance
should be received no later than 90 days after completion of the last affected aircraft of your
fleet.
AIRBUS will credit the man hours indicated in this Service Bulletin for corrections that are
performed on aircraft in warranty at the time of such correction. Credit will be at the agreed
in-house warranty labor rate. Claims for labor allowance should be received no later than 90
days after completion of the last affected warranted aircraft.
AIRBUS will credit the man hours indicated in this Service Bulletin for inspections that are
performed on aircraft in warranty at the time of such inspection. Credit will be at the agreed
in-house warranty labor rate. Claims for labor allowance should be received no later than 90
days after completion of the last affected warranted aircraft.
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organisation of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department.
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
France
E-mail: monitored.retrofit@airbus.com
C. LIST OF COMPONENTS
No Kit
D. LIST OF MATERIALS - OPERATOR SUPPLIED
(1) Consumable Materials
NOTE
: To accomplish this Service Bulletin it is necessary to use the
consumable materials listed i n the subsequent re ferenced tasks:
- MP Task A350-A-07-11-XX-00ZZZ-171Z-A
- MP Task A350-A-07-11-XX-00ZZZ-176Z-A
- MP Task A350-A-57- 51-71-01ZZZ-720Z-A.
(2) Components
NOTE
: To accomplish this Service Bulletin it is necessary to use the expendable
parts listed in the subsequent referenced task:
- MP Task A350-A-57- 51-71-01ZZZ-720Z-A.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 10
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 15

@A350
SERVICE BULLETIN
Component COMPB01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
7
 V5755009620000
 8
 PIN
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
NOTE
: The components listed above are only necessary if TASK
57P011-833-895 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Wheels or TASK
57P011-833-896 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Jacks (depending
on the inspection result) is to be accomplished. The quantity of these
items are to be ordered as required.
Component COMPB02
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
4
 NSA5060E9
 32
 NUT
6
 MS24665-372
 32
 PIN
9
 NSA5059E3
 8
 NUT
10
 MS24665-86
 8
 PIN
NOTE
: If you find part numbers of hardware components in the related kit(s)
which you cannot identify in the LIST OF COMPONENTS of this Service
Bulletin, refer to Standards Manual (SM). The SM will give you the
correct part number to part number relationship.
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
NOTE
: The components listed above are only necessary if TASK
57P011-833-895 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Wheels or TASK
57P011-833-896 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Jacks (depending
on the inspection result) is to be accomplished. The quantity of these
items are to be ordered as required.
(3) Equipment
None
E. PARTS TO BE RE-IDENTIFIED BY OPERATOR
None
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 11
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 16

@A350
SERVICE BULLETIN
F. TOOLING
(1) Tooling - Price and Availability
None
(2) Tools
NOTE
: To accomplish this Service Bulletin it is necessary to use the tools listed
in the subsequent re ferenced tasks:
- MP Task A350-A-07-11-XX-00ZZZ-171Z-A
- MP Task A350-A-07-11-XX-00ZZZ-176Z-A
- MP Task A350-A-32-12-XX-00ZZZ-397Z-A
- MP Task A350-A-32-12-XX-01ZZZ-397Z-A
- MP Task A350-A-57- 51-71-01ZZZ-520Z-A
- MP Task A350-A-57- 51-71-01ZZZ-720Z-A.
(3) Special Tools
None
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 12
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 17

@A350
SERVICE BULLETIN
3. ACCOMPLISHMENT INSTRUCTIONS
Task 57P011-832-895-001 - Inspection
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESP Task A350-A-20-55-
XX-01ZZZ-042Z-A.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
NOTE
: This Service Bulletin is classified mandatory or expected to be classified mandatory
by an Airworthiness Directive (AD). The paragraphs 3.C. and 3.D. in these
accomplishment instructions are Required for Compliance (RC) and must be done
to comply with the AD. Other paragraphs are recommended and may be deviated
from, done as part of other actions or done with accepted methods different from
those given in the Service Bulletin, as long as the RC paragraphs can be done and
the aircraft can be put back into a serviceable condition.
NOTE
: This Service Bulletin contains the instructions for the on-aircraft maintenance
necessary to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions contained herein, contact AIRBUS for further
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 13
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 18

@A350
SERVICE BULLETIN
instructions and approval.
NOTE
: The purpose of flowcharts is to supplement the information given in the Procedure
and Compliance paragraphs and not to serve as the primary source for tasks or
compliance times given in this Service Bulletin.
Task Associated Data
Zone
571 671
Access
Panel
 571DB 671DB
Manpower
TOTAL MANHOURS
 5.50
ELAPSED TIME (HOURS)
 2.75
A. GENERAL
(1) Subtask 57P011-910-401-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
System Description (SD)
 Task A350-A-06-3X-XX-01ZZZ-04CZ-A
Task A350-A-06-4X-XX-01ZZZ-04CZ-A
(a) For the identification of zones, refer to SD Task A350-A-06-3X-XX-01ZZZ-04CZ-A.
(b) For the identification of access panels, refer to SD Task A350-A-06-4X-
XX-01ZZZ-04CZ-A.
(c) Tag all the parts you must remove and retain to make the subsequent installation
easier.
(d) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.
(2) Subtask 57P011-839-401-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
B. PREPARATION
(1) Subtask 57P011-941-401-001 - Job Set-up
Manpower Resources
Skills
 NON SPECIFIC
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 14
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 19

@A350
SERVICE BULLETIN
References
Maintenance Procedure (MP)
 Task A350-A-24-41-XX-00ZZZ-170Z-A
Task A350-A-32-12-XX-00ZZZ-397Z-A
Task A350-A-57-51-71-01ZZZ-520Z-A
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Make sure that the aircraft is electrically grounded, refer to MP Task A350-A-24-41-
XX-00ZZZ-170Z-A.
(b) Open the Main Landing Gear (MLG) doors, refer to MP Task A350-A-32-12-
XX-00ZZZ-397Z-A.
(c) Remove the access panels 571DB and 671DB, refer to MP Task A350-
A-57-51-71-01ZZZ-520Z-A.
C. PROCEDURE
(1) Subtask 57P011-220-401-001 - Do a DET of the Four Retaining Pins installed in the
MLGSS Trunnion Block, LH Side
Work Zones and Access Panels
Zone
 Access/Work location
571
 Access
 Panel 571DB
Manpower Resources
Manhours
 0.25
Minimum number of person
 1
Subtask elapsed time
 0.25
Skills
 NON SPECIFIC
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 15
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 20

@A350
SERVICE BULLETIN
References
Fig. A-UFAAA
Flowchart
Sheet 01
Fig. A-UBBAA
Replacement of the Non-conforming
Retaining in the MLGSS Trunnion Block
Sheet 01
Sheet 02
Sheet 03
(a) Do a DET of the four retaining pins installed in the MLGSS trunnion block within the
threshold given in PLANNING INFORMATION paragraph E.(2).
Refer to Fig. A-UFAAA
, Fig. A-UBBAA Sheet 02
 and Fig. A-UBBAA Sheet 03
 .
NOTE
: Incorrect retaining pin can be identified through the gap existing
between the retaining pin and the Forward (FWD) surface of the
trunnion block. Correct retaining pin fully supports the FWD and
AFT surface of the trunnion block.
NOTE
: Use tools such as flash light, inspection mirror, magnifying glasses
and feeler gauge to aid the inspection.
1
 If the correct retaining pins are installed:
a
 No further action required.
2
 If the incorrect retaining pins are installed:
a
 Do a DET for damage or deformation.
<1> If damage or deformation is found:
- Contact AIRBUS before next flight and follow their instructions.
<2> If no damage or deformation is found:
<a> Replace the non-conforming retaining pins:
- If replacement of the non-conforming retaining pins are
possible with aircraft on wheels:
. In accordance with SUBTASK 57P011-960-401 001
Replace the Non-conforming Retaining Pins installed
in the MLGSS Trunnion Block with Aircraft on Wheels,
LH Side within the threshold given in PLANNING
INFORMATION paragraph E.(2)
. No further action required.
- If replacement of the non-conforming retaining pins are not
possible with aircraft on wheels, the aircraft will require
jacking:
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 16
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 21

@A350
SERVICE BULLETIN
. In accordance with SUBTASK 57P011-960-405 001
Replace the Non-conforming Retaining Pins installed
in the MLGSS Trunnion Block with Aircraft on Jacks,
LH Side within the threshold given in PLANNING
INFORMATION paragraph E.(2)
. No further action required.
(2) Subtask 57P011-220-402-001 - Do a DET of the Four Retaining Pins installed in the
MLGSS Trunnion Block, RH Side
Work Zones and Access Panels
Zone
 Access/Work location
671
 Access
 Panel 671DB
Manpower Resources
Manhours
 0.25
Minimum number of person
 1
Subtask elapsed time
 0.25
Skills
 NON SPECIFIC
References
Fig. A-UFAAA
Flowchart
Sheet 01
Fig. A-UBBAA
Replacement of the Non-conforming
Retaining in the MLGSS Trunnion Block
Sheet 01
Sheet 02
Sheet 03
(a) Do a DET of the four retaining pins installed in the MLGSS trunnion block within the
threshold given in PLANNING INFORMATION paragraph E.(2).
Refer to Fig. A-UFAAA
, Fig. A-UBBAA Sheet 02
 and Fig. A-UBBAA Sheet 03
 .
NOTE
: Incorrect retaining pin can be identified through the gap existing
between the retaining pin and the FWD surface of the trunnion
block. Correct retaining pin fully supports the FWD and AFT surface
of the trunnion block.
NOTE
: Use tools such as flash light, inspection mirror, magnifying glasses
and feeler gauge to aid the inspection.
1
 If the correct retaining pins are installed:
a
 No further action required.
2
 If the incorrect retaining pins are installed:
a
 Do a DET for damage or deformation.
<1> If damage or deformation is found:
- Contact AIRBUS before next flight and follow their instructions.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 17
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 22

@A350
SERVICE BULLETIN
<2> If no damage or deformation is found:
<a> Replace the non-conforming retaining pins:
- If replacement of the non-conforming retaining pins are
possible with aircraft on wheels:
. In accordance with SUBTASK 57P011-960-402 001
Replace the Non-conforming Retaining Pins installed
in the MLGSS Trunnion Block with Aircraft on Wheels,
RH Side within the threshold given in PLANNING
INFORMATION paragraph E.(2)
. No further action required.
- If replacement of the non-conforming retaining pins are not
possible with aircraft on wheels, the aircraft will require
jacking:
. In accordance with SUBTASK 57P011-960-406 001
Replace the Non-conforming Retaining Pins installed
in the MLGSS Trunnion Block with Aircraft on Jacks,
RH Side within the threshold given in PLANNING
INFORMATION paragraph E.(2)
. No further action required.
D. TEST
None
E. CLOSE-UP
(1) Subtask 57P011-942-401-001 - Close-up
Manpower Resources
Skills
 NON SPECIFIC
References
Maintenance Procedure (MP)
 Task A350-A-32-12-XX-01ZZZ-397Z-A
Task A350-A-57-51-71-01ZZZ-720Z-A
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the access panels 571DB and 671DB, refer to MP Task A350-
A-57-51-71-01ZZZ-720Z-A.
(c) Close the MLG doors, refer to MP T ask A350-A-32-12-XX-01ZZZ-397Z-A.
(d) Put the aircraft back to its initial configuration.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 18
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 23

@A350
SERVICE BULLETIN
Task 57P011-833-895-001 - Replacement of the Non-conforming Retaining Pins installed in
the MLGSS Trunnion Block with Aircraft on Wheels
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESP Task A350-A-20-55-
XX-01ZZZ-042Z-A.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
NOTE
: This Service Bulletin is classified mandatory or expected to be classified mandatory
by an Airworthiness Directive (AD). The paragraphs 3.C. and 3.D. in these
accomplishment instructions are Required for Compliance (RC) and must be done
to comply with the AD. Other paragraphs are recommended and may be deviated
from, done as part of other actions or done with accepted methods different from
those given in the Service Bulletin, as long as the RC paragraphs can be done and
the aircraft can be put back into a serviceable condition.
NOTE
: This Service Bulletin contains the instructions for the on-aircraft maintenance
necessary to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions contained herein, contact AIRBUS for further
instructions and approval.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 19
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 24

@A350
SERVICE BULLETIN
NOTE
: Discarded parts must be managed at the operator’s discretion.
Task Associated Data
Zone
571 671
Access
Panel
 571DB 671DB
Manpower
TOTAL MANHOURS
 9.00
ELAPSED TIME (HOURS)
 4.50
A. GENERAL
(1) Subtask 57P011-910-402-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Structural Repair (ASR)
 Task A350-A-51-42-XX-01ZZZ-667Z-A
Maintenance Procedure (MP)
 Task A350-A-20-51-50-01ZZZ-25BZ-A
System Description (SD)
 Task A350-A-06-3X-XX-01ZZZ-04CZ-A
Task A350-A-06-4X-XX-01ZZZ-04CZ-A
(a) For the identification of zones, refer to SD Task A350-A-06-3X-XX-01ZZZ-04CZ-A.
(b) For the identification of access panels, refer to SD Task A350-A-06-4X-
XX-01ZZZ-04CZ-A.
(c) Tag all the parts you must remove and retain to make the subsequent installation
easier.
(d) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.
(e) Remove and install fasteners in accordance with ASR Task A350-A-51-42-
XX-01ZZZ-667Z-A.
(f) For Standard Mechanical Torques, refer to MP Task A350-
A-20-51-50-01ZZZ-25BZ-A.
(g) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in ASR Data Module 51-4, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in ASR Data Module 51-4 may be used. In addition, washers may
be installed for fastener grip length in accordance with ASR Data Module 51-4.
(2) Subtask 57P011-839-402-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 20
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 25

@A350
SERVICE BULLETIN
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
B. PREPARATION
(1) Subtask 57P011-941-402-001 - Job Set-up
Manpower Resources
Skills
 NON SPECIFIC
References
Maintenance Procedure (MP)
 Task A350-A-24-41-XX-00ZZZ-170Z-A
Task A350-A-32-12-XX-00ZZZ-397Z-A
Task A350-A-57-51-71-01ZZZ-520Z-A
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Make sure that the aircraft is electrically grounded, refer to MP Task A350-A-24-41-
XX-00ZZZ-170Z-A.
(b) Open the MLG doors, refer to MP T ask A350-A-32-12-XX-00ZZZ-397Z-A.
(c) Remove the access panels 571DB and 671DB, refer to MP Task A350-
A-57-51-71-01ZZZ-520Z-A.
C. PROCEDURE
(1) Subtask 57P011-960-401-001 - Replace the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Wheels, LH Side
Work Zones and Access Panels
Zone
 Access/Work location
571
 Access
 Panel 571DB
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 21
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 26

@A350
SERVICE BULLETIN
Manpower Resources
Manhours
 2.00
Minimum number of person
 1
Subtask elapsed time
 2.00
Skills
 AIRFRAME
Material necessary to do the job
Component COMPB01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
7
 V5755009620000
 4
 PIN
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
NOTE
: The components listed above are only necessary if TASK
57P011-833-895 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Wheels or TASK
57P011-833-896 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Jacks (depending
on the inspection result) is to be accomplished. The quantity of these
items are to be ordered as required.
Component COMPB02
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
4
 NSA5060E9
 16
 NUT
6
 MS24665-372
 16
 PIN
9
 NSA5059E3
 4
 NUT
10
 MS24665-86
 4
 PIN
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
NOTE
: The components listed above are only necessary if TASK
57P011-833-895 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Wheels or TASK
57P011-833-896 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Jacks (depending
on the inspection result) is to be accomplished. The quantity of these
items are to be ordered as required.
References
Fig. A-UBAAA
Removal/Installation of the Tension
Straps on the MLGSS
Sheet 01
Fig. A-UBBAA
Replacement of the Non-conforming
Retaining in the MLGSS Trunnion Block
Sheet 01
Sheet 02
Sheet 03
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 22
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 27

@A350
SERVICE BULLETIN
NOTE
: If replacement of the non-conforming retaining pins are required for RH
side only, in accordance with SUBTASK 57P011-960-402 001 Replace
the Non-conforming Retaining Pins installed in the MLGSS Trunnion
Block with Aircraft on Wheels, RH Side .
(a) Replace the non-conforming retaining pins within the threshold given in PLANNING
INFORMATION paragraph E.(2).
Refer to Fig. A-UBAAA
 and Fig. A-UBBAA
.
1
 Replace the upper non-conforming retaining pins.
NOTE
: Only the non-conforming retaining pins have to be replaced.
All the retaining pins that are correctly installed, should be
ignored.
a
 Remove the upper tension strap as shown on Fig. A-UBAAA
 view B:
8 Pin-Cotter Item (6) Discard
8 Nut Item (4) Discard
8 Washer Item (5) Retain
8 Bolt Item (3) Retain
1 Upper Tension Strap Item (1) Retain
b
 Remove as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Cotter Item (10) Discard
2 Nut Item (9) Discard
2 Bolt Item (8) Retain
2 Pin-Retaining Item (7) Discard
c
 Install as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Retaining V5755009620000 Item 7
2 Bolt Item (8) Retained at
removal
2 Nut NSA5059E3 Item 9
2 Pin-Cotter MS24665-86 Item 10
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 23
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 28

@A350
SERVICE BULLETIN
d
 Install the upper tension strap as shown on Fig. A-UBAAA
 view B:
1 Upper Tension Strap Item (1) Retained at
removal
8 Bolt Item (3) Retained at
removal
8 Washer Item (5) Retained at
removal
8 Nut NSA5060E9 Item 4
8 Pin-Cotter MS24665-372 Item 6
2
 Replace the lower non-conforming retaining pins.
NOTE
: Only the non-conforming retaining pins have to be replaced.
All the retaining pins that are correctly installed, should be
ignored.
a
 Remove the lower tension strap as shown on Fig. A-UBAAA
 view B:
8 Pin-Cotter Item (6) Discard
8 Nut Item (4) Discard
8 Washer Item (5) Retain
8 Bolt Item (3) Retain
1 Lower Tension Strap Item (2) Retain
b
 Remove as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Cotter Item (10) Discard
2 Nut Item (9) Discard
2 Bolt Item (8) Retain
2 Pin-Retaining Item (7) Discard
c
 Install as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Retaining V5755009620000 Item 7
2 Bolt Item (8) Retained at
removal
2 Nut NSA5059E3 Item 9
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 24
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 29

@A350
SERVICE BULLETIN
2 Pin-Cotter MS24665-86 Item 10
d
 Install the lower tension strap as shown on Fig. A-UBAAA
 view B:
1 Lower Tension Strap Item (2) Retained at
removal
8 Bolt Item (3) Retained at
removal
8 Washer Item (5) Retained at
removal
8 Nut NSA5060E9 Item 4
8 Pin-Cotter MS24665-372 Item 6
(2) Subtask 57P011-960-402-001 - Replace the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Wheels, RH Side
Work Zones and Access Panels
Zone
 Access/Work location
671
 Access
 Panel 671DB
Manpower Resources
Manhours
 2.00
Minimum number of person
 1
Subtask elapsed time
 2.00
Skills
 AIRFRAME
Material necessary to do the job
Component COMPB01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
7
 V5755009620000
 4
 PIN
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
NOTE
: The components listed above are only necessary if TASK
57P011-833-895 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Wheels or TASK
57P011-833-896 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Jacks (depending
on the inspection result) is to be accomplished. The quantity of these
items are to be ordered as required.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 25
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 30

@A350
SERVICE BULLETIN
Component COMPB02
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
4
 NSA5060E9
 16
 NUT
6
 MS24665-372
 16
 PIN
9
 NSA5059E3
 4
 NUT
10
 MS24665-86
 4
 PIN
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
NOTE
: The components listed above are only necessary if TASK
57P011-833-895 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Wheels or TASK
57P011-833-896 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Jacks (depending
on the inspection result) is to be accomplished. The quantity of these
items are to be ordered as required.
References
Fig. A-UBAAA
Removal/Installation of the Tension
Straps on the MLGSS
Sheet 01
Fig. A-UBBAA
Replacement of the Non-conforming
Retaining in the MLGSS Trunnion Block
Sheet 01
Sheet 02
Sheet 03
(a) Replace the non-conforming retaining pins within the threshold given in PLANNING
INFORMATION paragraph E.(2).
Refer to Fig. A-UBAAA
 and Fig. A-UBBAA
.
1
 Replace the upper non-conforming retaining pins.
NOTE
: Only the non-conforming retaining pins have to be replaced.
All the retaining pins that are correctly installed, should be
ignored.
a
 Remove the upper tension strap as shown on Fig. A-UBAAA
 view B:
8 Pin-Cotter Item (6) Discard
8 Nut Item (4) Discard
8 Washer Item (5) Retain
8 Bolt Item (3) Retain
1 Upper Tension Strap Item (1) Retain
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 26
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 31

@A350
SERVICE BULLETIN
b
 Remove as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Cotter Item (10) Discard
2 Nut Item (9) Discard
2 Bolt Item (8) Retain
2 Pin-Retaining Item (7) Discard
c
 Install as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Retaining V5755009620000 Item 7
2 Bolt Item (8) Retained at
removal
2 Nut NSA5059E3 Item 9
2 Pin-Cotter MS24665-86 Item 10
d
 Install the upper tension strap as shown on Fig. A-UBAAA
 view B:
1 Upper Tension Strap Item (1) Retained at
removal
8 Bolt Item (3) Retained at
removal
8 Washer Item (5) Retained at
removal
8 Nut NSA5060E9 Item 4
8 Pin-Cotter MS24665-372 Item 6
2
 Replace the lower non-conforming retaining pins.
NOTE
: Only the non-conforming retaining pins have to be replaced.
All the retaining pins that are correctly installed, should be
ignored.
a
 Remove the lower tension strap as shown on Fig. A-UBAAA
 view B:
8 Pin-Cotter Item (6) Discard
8 Nut Item (4) Discard
8 Washer Item (5) Retain
8 Bolt Item (3) Retain
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 27
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 32

@A350
SERVICE BULLETIN
1 Lower Tension Strap Item (2) Retain
b
 Remove as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Cotter Item (10) Discard
2 Nut Item (9) Discard
2 Bolt Item (8) Retain
2 Pin-Retaining Item (7) Discard
c
 Install as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Retaining V5755009620000 Item 7
2 Bolt Item (8) Retained at
removal
2 Nut NSA5059E3 Item 9
2 Pin-Cotter MS24665-86 Item 10
d
 Install the lower tension strap as shown on Fig. A-UBAAA
 view B:
1 Lower Tension Strap Item (2) Retained at
removal
8 Bolt Item (3) Retained at
removal
8 Washer Item (5) Retained at
removal
8 Nut NSA5060E9 Item 4
8 Pin-Cotter MS24665-372 Item 6
D. TEST
None
E. CLOSE-UP
(1) Subtask 57P011-942-402-001 - Close-up
Manpower Resources
Skills
 NON SPECIFIC
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 28
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 33

@A350
SERVICE BULLETIN
References
Maintenance Procedure (MP)
 Task A350-A-32-12-XX-01ZZZ-397Z-A
Task A350-A-57-51-71-01ZZZ-720Z-A
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the access panels 571DB and 671DB, refer to MP Task A350-
A-57-51-71-01ZZZ-720Z-A.
(c) Close the MLG doors, refer to MP T ask A350-A-32-12-XX-01ZZZ-397Z-A.
(d) Put the aircraft back to its initial configuration.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 29
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 34

@A350
SERVICE BULLETIN
This Page Intentionally Left Blank
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 30
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 35

@A350
SERVICE BULLETIN
Task 57P011-833-896-001 - Replacement of the Non-conforming Retaining Pins installed in
the MLGSS Trunnion Block with Aircraft on Jacks
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESP Task A350-A-20-55-
XX-01ZZZ-042Z-A.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
NOTE
: This Service Bulletin is classified mandatory or expected to be classified mandatory
by an Airworthiness Directive (AD). The paragraphs 3.C. and 3.D. in these
accomplishment instructions are Required for Compliance (RC) and must be done
to comply with the AD. Other paragraphs are recommended and may be deviated
from, done as part of other actions or done with accepted methods different from
those given in the Service Bulletin, as long as the RC paragraphs can be done and
the aircraft can be put back into a serviceable condition.
NOTE
: This Service Bulletin contains the instructions for the on-aircraft maintenance
necessary to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions contained herein, contact AIRBUS for further
instructions and approval.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 31
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 36

@A350
SERVICE BULLETIN
NOTE
: Discarded parts must be managed at the operator’s discretion.
Task Associated Data
Zone
571 671
Access
Panel
 571DB 671DB
Manpower
TOTAL MANHOURS
 16.00
ELAPSED TIME (HOURS)
 4.50
A. GENERAL
(1) Subtask 57P011-910-403-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Structural Repair (ASR)
 Task A350-A-51-42-XX-01ZZZ-667Z-A
Maintenance Procedure (MP)
 Task A350-A-20-51-50-01ZZZ-25BZ-A
System Description (SD)
 Task A350-A-06-3X-XX-01ZZZ-04CZ-A
Task A350-A-06-4X-XX-01ZZZ-04CZ-A
(a) For the identification of zones, refer to SD Task A350-A-06-3X-XX-01ZZZ-04CZ-A.
(b) For the identification of access panels, refer to SD Task A350-A-06-4X-
XX-01ZZZ-04CZ-A.
(c) Tag all the parts you must remove and retain to make the subsequent installation
easier.
(d) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.
(e) Remove and install fasteners in accordance with ASR Task A350-A-51-42-
XX-01ZZZ-667Z-A.
(f) For Standard Mechanical Torques, refer to MP Task A350-
A-20-51-50-01ZZZ-25BZ-A.
(g) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in ASR Data Module 51-4, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in ASR Data Module 51-4 may be used. In addition, washers may
be installed for fastener grip length in accordance with ASR Data Module 51-4.
(2) Subtask 57P011-839-403-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 32
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 37

@A350
SERVICE BULLETIN
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
B. PREPARATION
(1) Subtask 57P011-941-403-001 - Job Set-up
Manpower Resources
Skills
 NON SPECIFIC
References
Maintenance Procedure (MP)
 Task A350-A-07-11-XX-00ZZZ-171Z-A
Task A350-A-24-41-XX-00ZZZ-170Z-A
Task A350-A-32-12-XX-00ZZZ-397Z-A
Task A350-A-57-51-71-01ZZZ-520Z-A
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Make sure that the aircraft is electrically grounded, refer to MP Task A350-A-24-41-
XX-00ZZZ-170Z-A.
(b) Open the MLG doors, refer to MP T ask A350-A-32-12-XX-00ZZZ-397Z-A.
(c) Remove the access panels 571DB and 671DB, refer to MP Task A350-
A-57-51-71-01ZZZ-520Z-A.
(d) Do the jacking procedure of the aircraft, refer to MP Task A350-A-07-11-
XX-00ZZZ-171Z-A.
(e) Record the load at each jacking point.
(f) Progressively lower the aircraft on to its wheels until the load at each wing jack has
reduced by 4441 kg (4357 daN).
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 33
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 38

@A350
SERVICE BULLETIN
C. PROCEDURE
(1) Subtask 57P011-960-405-001 - Replace the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Jacks, LH Side
Work Zones and Access Panels
Zone
 Access/Work location
571
 Access
 Panel 571DB
Manpower Resources
Manhours
 2.00
Minimum number of person
 1
Subtask elapsed time
 2.00
Skills
 AIRFRAME
Material necessary to do the job
Component COMPB01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
7
 V5755009620000
 4
 PIN
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
NOTE
: The components listed above are only necessary if TASK
57P011-833-895 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Wheels or TASK
57P011-833-896 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Jacks (depending
on the inspection result) is to be accomplished. The quantity of these
items are to be ordered as required.
Component COMPB02
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
4
 NSA5060E9
 16
 NUT
6
 MS24665-372
 16
 PIN
9
 NSA5059E3
 4
 NUT
10
 MS24665-86
 4
 PIN
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
NOTE
: The components listed above are only necessary if TASK
57P011-833-895 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Wheels or TASK
57P011-833-896 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Jacks (depending
on the inspection result) is to be accomplished. The quantity of these
items are to be ordered as required.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 34
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 39

@A350
SERVICE BULLETIN
References
Fig. A-UBAAA
Removal/Installation of the Tension
Straps on the MLGSS
Sheet 01
Fig. A-UBBAA
Replacement of the Non-conforming
Retaining in the MLGSS Trunnion Block
Sheet 01
Sheet 02
Sheet 03
NOTE
: If replacement of the non-conforming retaining pins are required for RH
side only, in accordance with SUBTASK 57P011-960-406 001 Replace
the Non-conforming Retaining Pins installed in the MLGSS Trunnion
Block with Aircraft on Jacks, RH Side .
(a) Replace the non-conforming retaining pins within the threshold given in PLANNING
INFORMATION paragraph E.(2).
Refer to Fig. A-UBAAA
 and Fig. A-UBBAA
.
1
 Replace the upper non-conforming retaining pins.
NOTE
: Only the non-conforming retaining pins have to be replaced.
All the retaining pins that are correctly installed, should be
ignored.
a
 Remove the upper tension strap as shown on Fig. A-UBAAA
 view B:
8 Pin-Cotter Item (6) Discard
8 Nut Item (4) Discard
8 Washer Item (5) Retain
8 Bolt Item (3) Retain
1 Upper Tension Strap Item (1) Retain
b
 Remove as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Cotter Item (10) Discard
2 Nut Item (9) Discard
2 Bolt Item (8) Retain
2 Pin-Retaining Item (7) Discard
c
 Install as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Retaining V5755009620000 Item 7
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 35
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 40

@A350
SERVICE BULLETIN
2 Bolt Item (8) Retained at
removal
2 Nut NSA5059E3 Item 9
2 Pin-Cotter MS24665-86 Item 10
d
 Install the upper tension strap as shown on Fig. A-UBAAA
 view B:
1 Upper Tension Strap Item (1) Retained at
removal
8 Bolt Item (3) Retained at
removal
8 Washer Item (5) Retained at
removal
8 Nut NSA5060E9 Item 4
8 Pin-Cotter MS24665-372 Item 6
2
 Replace the lower non-conforming retaining pins.
NOTE
: Only the non-conforming retaining pins have to be replaced.
All the retaining pins that are correctly installed, should be
ignored.
a
 Remove the lower tension strap as shown on Fig. A-UBAAA
 view B:
8 Pin-Cotter Item (6) Discard
8 Nut Item (4) Discard
8 Washer Item (5) Retain
8 Bolt Item (3) Retain
1 Lower Tension Strap Item (2) Retain
b
 Remove as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Cotter Item (10) Discard
2 Nut Item (9) Discard
2 Bolt Item (8) Retain
2 Pin-Retaining Item (7) Discard
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 36
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 41

@A350
SERVICE BULLETIN
c
 Install as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Retaining V5755009620000 Item 7
2 Bolt Item (8) Retained at
removal
2 Nut NSA5059E3 Item 9
2 Pin-Cotter MS24665-86 Item 10
d
 Install the lower tension strap as shown on Fig. A-UBAAA
 view B:
1 Lower Tension Strap Item (2) Retained at
removal
8 Bolt Item (3) Retained at
removal
8 Washer Item (5) Retained at
removal
8 Nut NSA5060E9 Item 4
8 Pin-Cotter MS24665-372 Item 6
(2) Subtask 57P011-960-406-001 - Replace the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Jacks, RH Side
Work Zones and Access Panels
Zone
 Access/Work location
671
 Access
 Panel 671DB
Manpower Resources
Manhours
 2.00
Minimum number of person
 1
Subtask elapsed time
 2.00
Skills
 AIRFRAME
Material necessary to do the job
Component COMPB01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
7
 V5755009620000
 4
 PIN
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 37
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 42

@A350
SERVICE BULLETIN
NOTE
: The components listed above are only necessary if TASK
57P011-833-895 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Wheels or TASK
57P011-833-896 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Jacks (depending
on the inspection result) is to be accomplished. The quantity of these
items are to be ordered as required.
Component COMPB02
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
4
 NSA5060E9
 16
 NUT
6
 MS24665-372
 16
 PIN
9
 NSA5059E3
 4
 NUT
10
 MS24665-86
 4
 PIN
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
NOTE
: The components listed above are only necessary if TASK
57P011-833-895 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Wheels or TASK
57P011-833-896 001 Replacement of the Non-conforming Retaining Pins
installed in the MLGSS Trunnion Block with Aircraft on Jacks (depending
on the inspection result) is to be accomplished. The quantity of these
items are to be ordered as required.
References
Fig. A-UBAAA
Removal/Installation of the Tension
Straps on the MLGSS
Sheet 01
Fig. A-UBBAA
Replacement of the Non-conforming
Retaining in the MLGSS Trunnion Block
Sheet 01
Sheet 02
Sheet 03
(a) Replace the non-conforming retaining pins within the threshold given in PLANNING
INFORMATION paragraph E.(2).
Refer to Fig. A-UBAAA
 and Fig. A-UBBAA
.
1
 Replace the upper non-conforming retaining pins.
NOTE
: Only the non-conforming retaining pins have to be replaced.
All the retaining pins that are correctly installed, should be
ignored.
a
 Remove the upper tension strap as shown on Fig. A-UBAAA
 view B:
8 Pin-Cotter Item (6) Discard
8 Nut Item (4) Discard
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 38
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 43

@A350
SERVICE BULLETIN
8 Washer Item (5) Retain
8 Bolt Item (3) Retain
1 Upper Tension Strap Item (1) Retain
b
 Remove as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Cotter Item (10) Discard
2 Nut Item (9) Discard
2 Bolt Item (8) Retain
2 Pin-Retaining Item (7) Discard
c
 Install as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Retaining V5755009620000 Item 7
2 Bolt Item (8) Retained at
removal
2 Nut NSA5059E3 Item 9
2 Pin-Cotter MS24665-86 Item 10
d
 Install the upper tension strap as shown on Fig. A-UBAAA
 view B:
1 Upper Tension Strap Item (1) Retained at
removal
8 Bolt Item (3) Retained at
removal
8 Washer Item (5) Retained at
removal
8 Nut NSA5060E9 Item 4
8 Pin-Cotter MS24665-372 Item 6
2
 Replace the lower non-conforming retaining pins.
NOTE
: Only the non-conforming retaining pins have to be replaced.
All the retaining pins that are correctly installed, should be
ignored.
a
 Remove the lower tension strap as shown on Fig. A-UBAAA
 view B:
8 Pin-Cotter Item (6) Discard
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 39
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 44

@A350
SERVICE BULLETIN
8 Nut Item (4) Discard
8 Washer Item (5) Retain
8 Bolt Item (3) Retain
1 Lower Tension Strap Item (2) Retain
b
 Remove as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Cotter Item (10) Discard
2 Nut Item (9) Discard
2 Bolt Item (8) Retain
2 Pin-Retaining Item (7) Discard
c
 Install as shown on Fig. A-UBBAA Sheet 02
 view C:
2 Pin-Retaining V5755009620000 Item 7
2 Bolt Item (8) Retained at
removal
2 Nut NSA5059E3 Item 9
2 Pin-Cotter MS24665-86 Item 10
d
 Install the lower tension strap as shown on Fig. A-UBAAA
 view B:
1 Lower Tension Strap Item (2) Retained at
removal
8 Bolt Item (3) Retained at
removal
8 Washer Item (5) Retained at
removal
8 Nut NSA5060E9 Item 4
8 Pin-Cotter MS24665-372 Item 6
D. TEST
None
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 40
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 45

@A350
SERVICE BULLETIN
E. CLOSE-UP
(1) Subtask 57P011-942-403-001 - Close-up
Manpower Resources
Skills
 NON SPECIFIC
References
Maintenance Procedure (MP)
 Task A350-A-07-11-XX-00ZZZ-176Z-A
Task A350-A-32-12-XX-01ZZZ-397Z-A
Task A350-A-57-51-71-01ZZZ-720Z-A
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the access panels 571DB and 671DB, refer to MP Task A350-
A-57-51-71-01ZZZ-720Z-A.
(c) Close the MLG doors, refer to MP T ask A350-A-32-12-XX-01ZZZ-397Z-A.
(d) Lower the aircraft, refer to M P Task A350-A-07-11-XX-00ZZZ-176Z-A.
(e) Put the aircraft back to its initial configuration.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 41
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 46

@A350
SERVICE BULLETIN
**CONF ALL
B
B
LH SHOWN
RH SYMMETRICAL
A
REAR SPAR
MAIN LANDING
GEAR
GEAR BEAM
RIB3
RIB5
A
Z571
Z671
LH
RH
(3)
(3)
(3)
(3)
(4)
(5)
(6) x4(4)
(5)
6 x4
(4)
(5) x4
(4)
(5)
6 x4
(2)
(1)
4 x4
6 x44 x4
(6) x4
4 x4
(6) x4
4 x4
(6) x4
6 x4
REAR SPAR
FUSE PIN
CARRIER
TRUNNION
BLOCK
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
P_SB_57P011_7_BAAA_01_00
Figure A-UBAAA - Sheet 01
Removal/Installation of the Tension Straps on the MLGSS
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 42
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 47

@A350
SERVICE BULLETIN
**CONF ALL
LH SHOWN
RH SYMMETRICAL
A
A
Z571
Z671
LH
RH
B
REAR SPAR
MAIN LANDING
GEAR
GEAR BEAM
RIB5
RIB3
P_SB_57P011_7_BBAA_01_01
Figure A-UBBAA - Sheet 01
Replacement of the Non-conforming Retaining in the MLGSS Trunnion Block
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 43
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 48

@A350
SERVICE BULLETIN
**CONF ALL
TYPICAL INSTALLATION
C
B
UPPER AND LOWER TENSION STRAPS REMOVED FOR CLARITY
(8)
(7)
7
9
(9)
(10)
10
FUSE PIN CARRIER REMOVED FOR CLARITY
REAR SPAR
TRUNNION
BLOCK
FUSE PIN
CARRIER
D
D
CC
C
C
P_SB_57P011_7_BBAA_02_02
Figure A-UBBAA - Sheet 02
Replacement of the Non-conforming Retaining in the MLGSS Trunnion Block
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 44
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 49

@A350
SERVICE BULLETIN
**CONF ALL
INCORRECT RETAINING PIN INSTALLATION
CORRECT RETAINING PIN INSTALLATION
GAP BETWEEN THE RETAINING PIN AND
THE FWD SURFACE OF THE TRUNNION BLOCK
NO GAP BETWEEN THE RETAINING PIN AND
THE FWD SURFACE OF THE TRUNNION BLOCK
D
TYPICAL
P_SB_57P011_7_BBAA_03_00
Figure A-UBBAA - Sheet 03
Replacement of the Non-conforming Retaining in the MLGSS Trunnion Block
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 45
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 50

@A350
SERVICE BULLETIN
**CONF ALL
NOTE:
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
DO A DETAILED VISUAL INSPECTION OF THE FOUR
RETAINING PINS INSTALLED IN THE TRUNNION
BLOCK OF THE MAIN LANDING GEAR SUPPORT
STRUCTURE WITHIN THE THRESHOLD GIVEN IN
THE PLANNING INFORMATION PARAGRAPH E.(2)
ARE
INCORRECT
RETAINING PINS
INSTALLED?
NO
IS
DAMAGE OR
DEFORMATION FOUND 
ON THE RETAINING
PINS?
YES
YES
CONTACT AIRBUS BEFORE NEXT FLIGHT
AND FOLLOW THEIR INSTRUCTIONS NO
IS THE
REPLACEMENT
OF THE RETAINING PINS
POSSIBLE WITH THE
AIRCRAFT ON
WHEELS?
NO
NO FURTHER ACTION
YES
REPLACE THE RETAINING PINS
WITHIN THE THRESHOLD GIVEN
IN THE PLANNING INFORMATION
PARAGRAPH E.(2) IN
ACCORDANCE WITH SUBTASK
57P011−960−401−001 AND
SUBTASK 57P011−960−402−001
REPLACE THE RETAINING PINS
WITHIN THE THRESHOLD GIVEN
IN THE PLANNING INFORMATION
PARAGRAPH E.(2) IN
ACCORDANCE WITH SUBTASK
57P011−960−405−001 AND
SUBTASK 57P011−960−406−001
P_SB_57P011_7_FAAA_01_01
Figure A-UFAAA - Sheet 01
Flowchart
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 46
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 51

@A350
SERVICE BULLETIN
Appendix 01 - Manpower Gantt Chart
**CONF ALL
For an explanation of the manhours and elapsed time, refer to the next page(s).
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 52

@A350
SERVICE BULLETIN
Appendix 01 - Manpower Gantt Chart
**CONF ALL
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A350−57−P011
MH ET/S
TOTAL MANHOURS
SB ELAPSED TIME
5.50
2.75
STEPS
2.50
2.50 1.25
0.25 0.25
MH
ET/S:
PER
MANHOURS
ELAPSED TIME PER STEP
NUMBER OF PERSONS
01
02
THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
01
02
NOTE:
PER
2
1
0.25 0.25 1
:
:
SB ELAPSED TIME
(HOURS)
0.5 1 1.5 23
IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
ARE NOT REFLECTED IN THIS GANTT CHART.
GET ACCESS
DO A DETAILED INSPECTION
OF THE FOUR RETAINING
PINS INSTALLED IN THE
MAIN LANDING GEAR
SUPPORT STRUCTURE
TRUNNION BLOCK, LH SIDE
CLOSE−UP
DO A DETAILED INSPECTION
OF THE FOUR RETAINING
PINS INSTALLED IN THE
MAIN LANDING GEAR
SUPPORT STRUCTURE
TRUNNION BLOCK, RH SIDE
2.50 1.252
P_SB_57P011_7_AAAA_01_00
Figure A-UAAAA - Sheet 01
Manpower Gantt Chart
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 2
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 53

@A350
SERVICE BULLETIN
Service Bulletin REPORTING
TITLE: WINGS - FITTINGS - INSPECTION OF RETAINING PIN INSTALLATION
AT THE TRUNNION BLOCK FUSE PINS
MODIFICATION No.: None
SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance and Flight
Operations Products if it is duly reported to Airbus.
General information
The SB Reporting policy is published in ISI 00.00.00135. This document provides information regarding:
the SB Reporting means and benefits, the update of customized Maintenance Products and customized
Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations Products" for
further information on the update of affected Flight Operations Products.
SB Reporting procedure
Standard practice to report SB is to use the online reporting application on AirbusWorld.
Refer to ISI 00.00.00179:
- For complete information on reporting means to Airbus. Question 2 "What are the standard
practices for SB reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs, Question 3 "What about
the reporting of prerequisite Service Bulletin?"
NOTE:
 ISI 00.00.00179 covers all the frequently asked questions about SB Reporting. It is revised on a
regular basis.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 54

@A350
SERVICE BULLETIN
QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin. The reported data
that you provide us will be used to analyse areas of difficulties and to take corrective action to further
improve the quality of our Service Bulletins.
We thank you for the time you have taken in completing this form.
(Please rate on a scale of 1 to 4, with 4 being the highest score)
- Quality rating of this SB 4321
- Quality rating of the Accomplishment Instructions 4321
- Quality rating of the Illustrations 4321
- Is this SB easy to understand ? Y/N
If you have had difficulties in the accomplishment of this SB please quote below the area(s) and give a
short description of the issue.
Planning Material Instructions
X Effectivity X Kit content X Preparation
X Reason X List of Materials Operator Supplied X Mod/Inspection
X Manpower X Industry support X Test
X References X Re-identification X Close-Up
X Publication X Tooling X Illustrations
Comments:
Operator: Date:
Name/Title:
Please return this form to:
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE
Attn : SEM4 Service Bulletins Management
F A X:( 3 3 )56 19 34 25 1
Or via your Resident Customer Support Office.
DATE: May 17/17 SERVICE BULLETIN No.: A350-57-P011
REVISION No.: 00 - May 17/17 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
