# Airbus Service Bulletin A350-57-P090

Copy: No revision named ("SB A350-57-P090-00"), 57 pages: PDF https://openairdocs.org/files/sha256/b5/cf/b5cf1d3dc81f7e1bb587bf4d853b216fe465cde2d4a177f3ab686eb1aa0f1e63; text https://openairdocs.org/service-documents/airbus/a350-57-p090/file/b5cf1d3dc81f.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2023-1883, the docket of AD 2024-08-01. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A350-57-P090
- Page: https://openairdocs.org/service-documents/airbus/a350-57-p090

## Text (57 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2023-1883, the docket of AD 2024-08-01. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 1
CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
 
The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.
ATA SYSTEM: 57
TITLE: WINGS - INBOARD FLAP - INTRODUCE REPLACEMENT LH INBOARD
FLAP FOLLOWING INSPECTION FINDING ON TRUNNION (SB ONLY)
MODIFICATION No.:
120317L01293

### Page 2

A350
SERVICE BULLETIN
SUMMARY
REV 00 Feb 05/24 A350-57-P090
Page 2
ATA SYSTEM: 57
TITLE: WINGS - INBOARD FLAP - INTRODUCE REPLACEMENT LH INBOARD
FLAP FOLLOWING INSPECTION FINDING ON TRUNNION (SB ONLY)
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
CONF 001
MODIFICATION CLASSIFICATION
MAJOR 120317L01293
MINOR None
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
CONF 002
MODIFICATION CLASSIFICATION
MAJOR 120317L01293
MINOR None
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
CONF ALL
B. REASON
(1) History
Following AIRBUS inspection program of the A350-900 inboard flap, cracks were
discovered on the trunnion as a result of unexpected material behavior. AIRBUS
released Inspection Service Bulletin (ISB) No. A350-57-P077 to perform a detailed Non-
Destructive T est (NDT) inspection of the trunnion. In case of findings, a replacement of
the inboard flap is required.
Due to a shortage of inboard flap spares covering the affected fleet, there is a need for
a Modification (MOD) to modify a new production standard inboard flap into an inboard
flap that can be fitted on the affected fleet.
(2) Objective/Action
This Service Bulletin provides instructions to install a new inboard flap removing
mandatory inspections as detailed in ISB No. A350-57-P077.
If the content of this Service Bulletin has been accomplished by Repair and Design
Approval Form (RDAF) Ref. 81224978/003/2023 on Manufacturer Serial Number (MSN)
0006, then it is only necessary to report the accomplishment of this Service Bulletin
by completing and submitting the Service Bulletin reporting sheet.
(3) Advantages
Accomplishment of this Service Bulletin cancels the requirements of ISB No. A350-57-
P077.

### Page 3

A350
SERVICE BULLETIN
SUMMARY
REV 00 Feb 05/24 A350-57-P090
Page 3
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE RECOMMENDED COST SAVING NO
A/C OPERATION
AFFECTED
NO VENDOR SB NO
CANCELS INSPECTION SB YES ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD NO
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO
NOTE: Service Bulletin recommended to be accomplished to prevent significant
operational disruptions.
NOTE: This Service Bulletin is recommended to be accomplished following findings from
the inspection programme given in ISB No. A350-57-P077.
D. MAINTENANCE CONFIGURATION
CONF 001
MAINTENANCE CONFIGURATION
FLAPS/SLATS RETRACTED YES
CONF 002
MAINTENANCE CONFIGURATION
FLAPS/SLATS RETRACTED YES
CONF ALL
E. MATERIAL PRICE INFORMATION
CONF 001
(1) Replacement of the LH Inboard Flap Assy
(a) T ask set A350-A-57-XX-P090-01000-93AA-A Replacement of the LH Inboard Flap
Assy
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Part kit 57P090D02R00 1 31930.00 USD Plates, sleeve, ring, washers,
nuts, bolts and cotter pin
Components See SB See Note Plate, caps and flap
NOTE: Price information to be obtained from the given supplier.
CONF 002
(1) Replacement of the LH Inboard Flap Assy

### Page 4

A350
SERVICE BULLETIN
SUMMARY
REV 00 Feb 05/24 A350-57-P090
Page 4
(a) T ask set A350-A-57-XX-P090-01000-93AA-A Replacement of the LH Inboard Flap
Assy
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Part kit 57P090D03R01 1 6080.00 USD Bolts, washers, nuts, sleeve
and cotter pin
Components See SB See Note Plate, caps and flap
NOTE: Price information to be obtained from the given supplier.
CONF ALL
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
CPA DAL DLH ETH FBU FIN HVN QTR SIA THA
G. CONCURRENT REQUIREMENTS
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this Service Bulletin:
Service Bulletin(s) Modification(s)
Ref. SB A350-57-P018 112002L00931 112103L00933
NOTE: Service Bulletin No. A350-57-P018 (WINGS - TRAILING EDGE AND TRAILING EDGE
DEVICES - REVISE CRUISE ROLLER AND FLAP UNICORN TO INCREASE OPERATIONAL
DURABILITY).
NOTE: Service Bulletin No. A350-57-P018 (WINGS - TRAILING EDGE AND TRAILING EDGE
DEVICES - REVISE CRUISE ROLLER AND FLAP UNICORN TO INCREASE OPERATIONAL
DURABILITY) is a concurrent requirement if MOD No. 112002L00931 has not been
embodied before delivery.
NOTE: When an operator records the SB report, it is also the operator's responsibility to
report all prerequisite Service Bulletin to AIRBUS.
H. NATURE OF THE WORK
CONF 001
(1) Replacement of the LH Inboard Flap Assy
(a) T ask set A350-A-57-XX-P090-01000-93AA-A Replacement of the LH Inboard Flap
Assy
AIRCRAFT YES
EQUIPMENT NO
CONF 002
(1) Replacement of the LH Inboard Flap Assy
(a) T ask set A350-A-57-XX-P090-01000-93AA-A Replacement of the LH Inboard Flap
Assy
AIRCRAFT YES
EQUIPMENT NO

### Page 5

A350
SERVICE BULLETIN
SUMMARY
REV 00 Feb 05/24 A350-57-P090
Page 5
CONF ALL
I. MANPOWER
CONF 001
(1) Replacement of the LH Inboard Flap Assy
(a) T ask set A350-A-57-XX-P090-01000-93AA-A Replacement of the LH Inboard Flap
Assy
MANPOWER
TOTAL MAN-HOURS 61.00 h
ELAPSED TIME (HOURS) 21.00 h
CONF 002
(1) Replacement of the LH Inboard Flap Assy
(a) T ask set A350-A-57-XX-P090-01000-93AA-A Replacement of the LH Inboard Flap
Assy
MANPOWER
TOTAL MAN-HOURS 61.00 h
ELAPSED TIME (HOURS) 21.00 h

### Page 6

A350
SERVICE BULLETIN
SUMMARY
Figure ICN-A350-A-57XXP090-A-FAPE3-07738-A-001-01 Fig.SA Sol.AA SHEET 1/1
REV 00 Feb 05/24 A350-57-P090General Overview
Page 6
CONF ALL
J. GENERAL OVERVIEW
CONF ALL
Z561
A
A
REPLACEMENT OF THE
LH INBOARD FLAP ASSY
ICN-A350-A-57XXP090-A-FAPE3-07738-A-001-01

### Page 7

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 7
ATA SYSTEM: 57
TITLE: WINGS - INBOARD FLAP - INTRODUCE REPLACEMENT LH INBOARD
FLAP FOLLOWING INSPECTION FINDING ON TRUNNION (SB ONLY)
1. PLANNING INFORMATION
A. APPLICABILITY
NOTE: This modification is applicable by Service Bulletin only.
(1) Models
ON A/C 0005-0023, 0026-0032, 0034-0046
350-941
CONF ALL
(2) Applicability by MSN
0005-0023 0026-0032 0034-0046
(3) MSN by configuration
CONF 001
MSN CONFIGURATION
0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015
0016 0017 0018 0019 0020
001
CONF 002
MSN CONFIGURATION
0021 0022 0023 0026 0027 0028 0029 0030 0031 0032 0034
0035 0036 0037 0038 0039 0040 0041 0042 0043 0044 0045
0046
002
CONF ALL
(4) Configuration definition
CONF 001
Configuration 001
CONF 001 is applicable for all the aircraft on which MOD No. 102046L00129 is
not embodied.
CONF 001 retrofits following modifications: 120317L01293.
CONF 002
Configuration 002
CONF 002 is applicable for all the aircraft on which MOD No. 102046L00129 is
embodied.
CONF 002 retrofits following modifications: 120317L01293.
CONF ALL
B. CONCURRENT REQUIREMENTS
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this Service Bulletin:

### Page 8

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 8
Service Bulletin(s) Modification(s)
Ref. SB A350-57-P018 112002L00931 112103L00933
NOTE: Service Bulletin No. A350-57-P018 (WINGS - TRAILING EDGE AND TRAILING EDGE
DEVICES - REVISE CRUISE ROLLER AND FLAP UNICORN TO INCREASE OPERATIONAL
DURABILITY).
NOTE: Service Bulletin No. A350-57-P018 (WINGS - TRAILING EDGE AND TRAILING EDGE
DEVICES - REVISE CRUISE ROLLER AND FLAP UNICORN TO INCREASE OPERATIONAL
DURABILITY) is a concurrent requirement if MOD No. 112002L00931 has not been
embodied before delivery.
NOTE: When an operator records the SB report, it is also the operator's responsibility to
report all prerequisite Service Bulletin to AIRBUS.
C. REASON
(1) History
Following AIRBUS inspection program of the A350-900 inboard flap, cracks were
discovered on the trunnion as a result of unexpected material behavior. AIRBUS
released Inspection Service Bulletin (ISB) No. A350-57-P077 to perform a detailed Non-
Destructive T est (NDT) inspection of the trunnion. In case of findings, a replacement of
the inboard flap is required.
Due to a shortage of inboard flap spares covering the affected fleet, there is a need for
a Modification (MOD) to modify a new production standard inboard flap into an inboard
flap that can be fitted on the affected fleet.
(2) Objective/Action
This Service Bulletin provides instructions to install a new inboard flap removing
mandatory inspections as detailed in ISB No. A350-57-P077.
If the content of this Service Bulletin has been accomplished by Repair and Design
Approval Form (RDAF) Ref. 81224978/003/2023 on Manufacturer Serial Number (MSN)
0006, then it is only necessary to report the accomplishment of this Service Bulletin
by completing and submitting the Service Bulletin reporting sheet.
(3) Advantages
Accomplishment of this Service Bulletin cancels the requirements of ISB No. A350-57-
P077.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
T o accomplish this Service Bulletin it is necessary to:
(1) Replacement of the LH Inboard Flap Assy
(a) T ask set A350-A-57-XX-P090-01000-93AA-A Replacement of the LH Inboard Flap
Assy
CONF 001
1 Remove the LH Inboard Flap Assy
CONF 002
1 Remove the LH Inboard Flap Assy
CONF ALL

### Page 9

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 9
2 Modify the New LH Inboard Flap Assy on Bench
CONF 001
3 Install the LH Inboard Flap Assy
CONF 002
3 Install the LH Inboard Flap Assy
CONF ALL
E. COMPLIANCE
(1) Classification
RECOMMENDED: Service Bulletin recommended to be accomplished to prevent
significant operational disruptions.
(2) Accomplishment Timescale
This Service Bulletin is recommended to be accomplished following findings from the
inspection programme given in ISB No. A350-57-P077.
F. APPROVAL
The technical content of this document is approved under the authority of the Design
Organisation Approval ref. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER
CONF 001
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Replacement of the LH Inboard Flap Assy
(a) T ask set A350-A-57-XX-P090-01000-93AA-A Replacement of the LH Inboard Flap
Assy
PREPARATION
Job Set-Up 6.00 h
PROCEDURE
Remove the LH Inboard Flap Assy 18.00 h
Modify the New LH Inboard Flap Assy on Bench 1.00 h BENCH
Install the LH Inboard Flap Assy 24.00 h
PREPARATION FOR TEST
Preparation for T est 1.50 h
TEST
T est 1.50 h
CLOSE-UP
Close-Up 9.00 h
TOTAL MAN-HOURS 61.00 h

### Page 10

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 10
ELAPSED TIME (HOURS) 21.00 h
CONF 002
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Replacement of the LH Inboard Flap Assy
(a) T ask set A350-A-57-XX-P090-01000-93AA-A Replacement of the LH Inboard Flap
Assy
PREPARATION
Job Set-Up 6.00 h
PROCEDURE
Remove the LH Inboard Flap Assy 18.00 h
Modify the New LH Inboard Flap Assy on Bench 1.00 h BENCH
Install the LH Inboard Flap Assy 24.00 h
PREPARATION FOR TEST
Preparation for T est 1.50 h
TEST
T est 1.50 h
CLOSE-UP
Close-Up 9.00 h
TOTAL MAN-HOURS 61.00 h
ELAPSED TIME (HOURS) 21.00 h
CONF ALL
H. WEIGHT AND BALANCE
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer's Empty Weight (MEW) and do not include operator's items. The definition of
MEW and operator's items is given in the Weight and Balance Manual (WBM), Ref. WBM.
FOR SERIE-350-900
Manufacturer's Empty Weight -1.4 kg (-3.086 lb)
Effect on Balance -75.246 kg.m (-544.254 lb.ft)
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
CONCURRENT SERVICE BULLETIN (SB)
A350-57-P018
CONF 001
(1) Replacement of the LH Inboard Flap Assy

### Page 11

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 11
(a) T ask set A350-A-57-XX-P090-01000-93AA-A Replacement of the LH Inboard Flap
Assy
AIRCRAFT STRUCTURAL REPAIR (ASR)
A350-A-51-42-XX-01ZZZ-667Z-A A350-A-51-43-XX-01ZZZ-667Z-A
A350-A-51-75-12-00ZZZ-660Z-A
CONSUMABLE MATERIAL LIST (CML)
See manual
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
INTRODUCTION (INTRO)
A350-A-00-61-04-11ZZZ-018Z-D
MAINTENANCE PROCEDURE (MP)
A350-A-11-XX-XX-00ZZZ-691Z-A A350-A-24-41-XX-00ZZZ-170Z-A
A350-A-57-54-62-00ZZZ-520Z-A
A350-A-57-54-62-00ZZZ-720Z-A
A350-A-57-57-61-00ZZZ-720Z-A
PROCESS AND MATERIAL SPECIFICATION (PMS)
01-06-12
SYSTEM DESCRIPTION (SD)
A350-A-06-3X-XX-01ZZZ-04CZ-A A350-A-06-4X-XX-01ZZZ-04CZ-A
STANDARDS MANUAL (SM)
See manual
TECHNICAL FOLLOW UP (TFU)
57.50.00035
WEIGHT AND BALANCE MANUAL (WBM)
See manual
CONF 002
(1) Replacement of the LH Inboard Flap Assy
(a) T ask set A350-A-57-XX-P090-01000-93AA-A Replacement of the LH Inboard Flap
Assy
AIRCRAFT STRUCTURAL REPAIR (ASR)
A350-A-51-42-XX-01ZZZ-667Z-A A350-A-51-43-XX-01ZZZ-667Z-A
A350-A-51-75-12-00ZZZ-660Z-A
CONSUMABLE MATERIAL LIST (CML)
See manual

### Page 12

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 12
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
INTRODUCTION (INTRO)
A350-A-00-61-04-11ZZZ-018Z-D
MAINTENANCE PROCEDURE (MP)
A350-A-11-XX-XX-00ZZZ-691Z-A A350-A-24-41-XX-00ZZZ-170Z-A
A350-A-57-54-62-00ZZZ-520Z-A
A350-A-57-54-62-00ZZZ-720Z-A
A350-A-57-57-61-00ZZZ-720Z-A
PROCESS AND MATERIAL SPECIFICATION (PMS)
01-06-12
SYSTEM DESCRIPTION (SD)
A350-A-06-3X-XX-01ZZZ-04CZ-A A350-A-06-4X-XX-01ZZZ-04CZ-A
STANDARDS MANUAL (SM)
See manual
TECHNICAL FOLLOW UP (TFU)
57.50.00035
WEIGHT AND BALANCE MANUAL (WBM)
See manual
CONF ALL
K. PUBLICATION AFFECTED
MAINTENANCE ILLUSTRATED PART DATA (MIPD)
See manual
STRUCTURAL REPAIR IPD (SRIPD)
See manual
L. INDUSTRY SUPPORT INFORMATION
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign. For detailed
support, please refer to the related RIL V57M22002681.
For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department: monitored.retrofit@airbus.com.

### Page 13

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 13
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
CONF 001
Material for task set A350-A-57-XX-P090-01000-93AA-A Replacement of the LH
Inboard Flap Assy
MATERIAL QTY SEE NOTES
Referenced tools See SB
Consumables See SB
Referenced consumables See SB
Part kit 57P090D02R00 1
Components See SB
Referenced parts See SB
Re-identified parts See SB
Interchangeable parts See SB
CONF 002
Material for task set A350-A-57-XX-P090-01000-93AA-A Replacement of the LH
Inboard Flap Assy
MATERIAL QTY SEE NOTES
Referenced tools See SB
Consumables See SB
Referenced consumables See SB
Part kit 57P090D03R01 1
Components See SB
Referenced parts See SB
Re-identified parts See SB
Interchangeable parts See SB
CONF ALL
B. TOOLING
CONF 001
Referenced tools for task set A350-A-57-XX-P090-01000-93AA-A Replacement of
the LH Inboard Flap Assy
T o accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. MP A350-A-11-XX-XX-00ZZZ-691Z-A
Ref. MP A350-A-57-54-62-00ZZZ-520Z-A
Ref. MP A350-A-57-54-62-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-00ZZZ-720Z-A
CONF 002
Referenced tools for task set A350-A-57-XX-P090-01000-93AA-A Replacement of
the LH Inboard Flap Assy
T o accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. MP A350-A-11-XX-XX-00ZZZ-691Z-A

### Page 14

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 14
Ref. MP A350-A-57-54-62-00ZZZ-520Z-A
Ref. MP A350-A-57-54-62-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-00ZZZ-720Z-A
CONF ALL
C. CONSUMABLES
CONF 001
Consumables for task set A350-A-57-XX-P090-01000-93AA-A Replacement of the
LH Inboard Flap Assy
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
04DCA3
Primer Epoxy Paint - Low
VOC Chromate Free -
External Structure
04PAC2 Polyurethane Coating - -Wear ResistantStructure
04SBA3 Varnish Polyurethane - LowVOC - External Structure
08BAA9 Non Aqueous Cleaner -General
14QFC1 Wire - Locking Dia: 0.8 mmCRES
14SBA1 T extile - Lint free Cotton
CONF 002
Consumables for task set A350-A-57-XX-P090-01000-93AA-A Replacement of the
LH Inboard Flap Assy
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
04DCA3
Primer Epoxy Paint - Low
VOC Chromate Free -
External Structure
04PAC2 Polyurethane Coating - -Wear ResistantStructure
04SBA3 Varnish Polyurethane - LowVOC - External Structure
08BAA9 Non Aqueous Cleaner -General
14QFC1 Wire - Locking Dia: 0.8 mmCRES
14SBA1 T extile - Lint free Cotton
CONF 001
Referenced consumables for task set A350-A-57-XX-P090-01000-93AA-A
Replacement of the LH Inboard Flap Assy
T o accomplish this Service Bulletin it is necessary to use the consumable materials listed in:
Ref. MP A350-A-11-XX-XX-00ZZZ-691Z-A
Ref. MP A350-A-57-54-62-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-00ZZZ-720Z-A

### Page 15

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 15
CONF 002
Referenced consumables for task set A350-A-57-XX-P090-01000-93AA-A
Replacement of the LH Inboard Flap Assy
T o accomplish this Service Bulletin it is necessary to use the consumable materials listed in:
Ref. MP A350-A-11-XX-XX-00ZZZ-691Z-A
Ref. MP A350-A-57-54-62-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-00ZZZ-720Z-A
CONF ALL
D. LIST OF NEW PARTS
CONF 001
Part kit 57P090D02R00
Cost 31930.00 USD
Availability 490 d (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
airbus.kit@airbus.com.
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.
Procurement address D4296
AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
Phone: +49 40 743 51775
E-mail: airbus.kit@airbus.com
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
4 ABS1149AP2375B 1 WASHER
22 ABS1149AP1125B 1 WASHER
30 MS24665-155 1 PIN
61 V5759136020200 1 WASHER
62 V5759136620200 1 SLEEVE
63 V5759136320200 1 WASHER
64 V5759136220200 1 NUT
65 V5759136120200 1 RING
66 ABS1830L8A44 1 BOLT
67 V5759136720000 1 WASHER

### Page 16

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 16
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
69 ABS0114T4-4 3 BOLT
70 NSA5379-4CK 6 WASHER
71 NAS1726C4PE 3 NUT
72 ABS1830L10A40 8 BOLT
73 V5759137420200 2 PLATE
74 V5759137520200 1 PLATE
75 V5759137520300 1 PLATE
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 002
Part kit 57P090D03R01
Cost 6080.00 USD
Availability 490 d (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
airbus.kit@airbus.com.
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.
Procurement address D4296
AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
Phone: +49 40 743 51775
E-mail: airbus.kit@airbus.com
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
4 ABS1149AP2375B 1 WASHER
22 ABS1149AP1125B 1 WASHER
30 MS24665-155 1 PIN
62 V5759136620200 1 SLEEVE
63 V5759136320200 1 WASHER
66 ABS1830L8A44 1 BOLT
71 NAS1726C4PE 3 NUT

### Page 17

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 17
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
72 ABS1830L10A40 8 BOLT
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 001
Components for task set A350-A-57-XX-P090-01000-93AA-A Replacement of the
LH Inboard Flap Assy
Procurement address
D4296
AIRBUS Material, Logistics and Suppliers Standard
Parts
Customer Order Fulfilment
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com or via SPEC2000
D4296
AIRBUS Material, Logistics and Suppliers
Customer Order Fulfilment
Weg beim Jaeger 150
22335 HAMBURG
GERMANY
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com
NOTE(S)
For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
1 WQ209CBAAAAA(D4296) 1 FLAP (1) (2)
38 ASNA2879E050(D4296) 3 CAP (1) (3) (4)
58 ABS0970-72 (D4296) 1 PLATE (1) (3) (4)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): Operator supplied AIRBUS parts required to accomplish this Service Bulletin are to be
purchased by a spares purchase order.
(3): Operator supplied standard hardware parts, required to accomplish this Service
Bulletin, are to be supplied from the operator's stock.

### Page 18

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 18
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
(4): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.
CONF 002
Components for task set A350-A-57-XX-P090-01000-93AA-A Replacement of the
LH Inboard Flap Assy
Procurement address
D4296
AIRBUS Material, Logistics and Suppliers Standard
Parts
Customer Order Fulfilment
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com or via SPEC2000
D4296
AIRBUS Material, Logistics and Suppliers
Customer Order Fulfilment
Weg beim Jaeger 150
22335 HAMBURG
GERMANY
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com
NOTE(S)
For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
1 WQ209CBAAAAA(D4296) 1 FLAP (1) (2)
38 ASNA2879E050(D4296) 3 CAP (1) (3) (4)
58 ABS0970-72 (D4296) 1 PLATE (1) (3) (4)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): Operator supplied AIRBUS parts required to accomplish this Service Bulletin are to be
purchased by a spares purchase order.
(3): Operator supplied standard hardware parts, required to accomplish this Service
Bulletin, are to be supplied from the operator's stock.
(4): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.

### Page 19

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 19
CONF 001
Referenced parts for task set A350-A-57-XX-P090-01000-93AA-A Replacement of
the LH Inboard Flap Assy
T o accomplish this Service Bulletin it is necessary to use the expendable parts listed in:
Ref. MP A350-A-57-54-62-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-00ZZZ-720Z-A
CONF 002
Referenced parts for task set A350-A-57-XX-P090-01000-93AA-A Replacement of
the LH Inboard Flap Assy
T o accomplish this Service Bulletin it is necessary to use the expendable parts listed in:
Ref. MP A350-A-57-54-62-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-00ZZZ-720Z-A
CONF ALL
E. LIST OF EXISTING PARTS
CONF 001
Re-identified parts for task set A350-A-57-XX-P090-01000-93AA-A Replacement of
the LH Inboard Flap Assy
ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
1 WQ209A1AAACW FLAP (1) WQ209CBAAAAA
CONF 002
Re-identified parts for task set A350-A-57-XX-P090-01000-93AA-A Replacement of
the LH Inboard Flap Assy
ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
1 WQ209A1AAACW FLAP (1) WQ209CBAAAAA
CONF 001
Interchangeable parts for task set A350-A-57-XX-P090-01000-93AA-A
Replacement of the LH Inboard Flap Assy
DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
FLAP ASSY-INBOARD WQ209AQAAAAA WQ209CBAAAAA 03 (1) (2)
FLAP ASSY-INBOARD WQ209BDAAAAA WQ209CBAAAAA 03 (1) (3)
NOTE(S)
For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter
2).
(1): The interchangeability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.
(2): Not interchangeable, but one way interchangeable with conditions:
- Part Number (PN) WQ209CBAAAAA can replace the PN WQ209AQAAAAA if PN
WQ209CBAAAAA has been modified in accordance with the instructions given
in this Service Bulletin (becoming PN WQ209A1AAACW)
- PN WQ209AQAAAAA cannot replace PN WQ209CBAAAAA modified in
accordance with the instructions given in this Service Bulletin (becoming PN
WQ209A1AAACW).

### Page 20

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 20
DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
(3): Not interchangeable, but one way interchangeable with conditions:
- PN WQ209CBAAAAA can replace the PN WQ209BDAAAAA if PN
WQ209CBAAAAA has been modified in accordance with the instructions given
in this Service Bulletin (becoming PN WQ209A1AAACW)
- PN WQ209BDAAAAA cannot replace PN WQ209CBAAAAA modified in
accordance with the instructions given in this Service Bulletin (becoming PN
WQ209A1AAACW).
CONF 002
Interchangeable parts for task set A350-A-57-XX-P090-01000-93AA-A
Replacement of the LH Inboard Flap Assy
DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
FLAP ASSY-INBOARD WQ209ATAAAAA WQ209CBAAAAA 03 (1) (2)
FLAP ASSY-INBOARD WQ209AYAAAAA WQ209CBAAAAA 03 (1) (3)
FLAP ASSY-INBOARD WQ209AZAAAAA WQ209CBAAAAA 03 (1) (4)
NOTE(S)
For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter
2).
(1): The interchangeability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.
(2): Not interchangeable, but one way interchangeable with conditions:
- Part Number (PN) WQ209CBAAAAA can replace the PN WQ209ATAAAAA if PN
WQ209CBAAAAA has been modified in accordance with the instructions given
in this Service Bulletin (becoming PN WQ209A1AAACW)
- PN WQ209ATAAAAA cannot replace PN WQ209CBAAAAA modified in
accordance with the instructions given in this Service Bulletin (becoming PN
WQ209A1AAACW).
(3): Not interchangeable, but one way interchangeable with conditions:
- PN WQ209CBAAAAA can replace the PN WQ209AYAAAAA if PN
WQ209CBAAAAA has been modified in accordance with the instructions given
in this Service Bulletin (becoming PN WQ209A1AAACW)
- PN WQ209AYAAAAA cannot replace PN WQ209CBAAAAA modified in
accordance with the instructions given in this Service Bulletin (becoming PN
WQ209A1AAACW).
(4): Not interchangeable, but one way interchangeable with conditions:
- PN WQ209CBAAAAA can replace the PN WQ209AZAAAAA if PN
WQ209CBAAAAA has been modified in accordance with the instructions given
in this Service Bulletin (becoming PN WQ209A1AAACW)
- PN WQ209AZAAAAA cannot replace PN WQ209CBAAAAA modified in
accordance with the instructions given in this Service Bulletin (becoming PN
WQ209A1AAACW).

### Page 21

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 21
CONF ALL
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A350-A-57-XX-P090-01000-93AA-A (A350-A-57-XX-P090-01ZZZ-93AZ-A)
Replacement of the LH Inboard Flap Assy
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO A MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESP A350-A-20-55-XX-01ZZZ-
042Z-A.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, contact AIRBUS for further instructions and
approval.
NOTE: Discarded parts must be managed at the operator's discretion.
A. TASK SET ASSOCIATED INFORMATION
CONF 001
Maintenance Configuration
Flaps/slats retracted
CONF 002
Maintenance Configuration
Flaps/slats retracted
Task Manpower
CONF 001
TOTAL MAN-HOURS 61.00 h

### Page 22

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 22
CONF 002
TOTAL MAN-HOURS 61.00 h
CONF 001
ELAPSED TIME (HOURS) 21.00 h
CONF 002
ELAPSED TIME (HOURS) 21.00 h
CONF ALL
B. PREPARATION
(1) Task A350-A-57-XX-P090-01001-540A-A (A350-A-57-XX-P090-01ZZZ-540Z-A)
Job Set-Up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 6.00 h
Minimum Number of person 3
Elapsed Time 2.00 h
Referenced Information
Manuals/Drawings References/Sheets
INTRO A350-A-00-61-04-11ZZZ-018Z-D
MP A350-A-24-41-XX-00ZZZ-170Z-AA350-A-57-54-62-00ZZZ-520Z-A
Procedure
NOTE: For the basic Aircraft configuration, refer to Ref. INTRO A350-A-00-61-04-
11ZZZ-018Z-D “Maintenance Procedure - Introduction”.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. MP A350-A-24-
41-XX-00ZZZ-170Z-A.
(b) Do the job set-up procedure as specified in the removal of the LH inboard flap
assy, refer to Ref. MP A350-A-57-54-62-00ZZZ-520Z-A.
C. PROCEDURE
CONF 001
(1) Task A350-A-57-XX-P090-01001-520A-A (A350-A-57-XX-P090-01ZZZ-520Z-A)
Remove the LH Inboard Flap Assy
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
561
Manpower/Resources/Skills
Man-hours 18.00 h
Minimum Number of person 3
Elapsed Time 6.00 h
Skills Airframe

### Page 23

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 23
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-57-54-62-00ZZZ-520Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-04CZ-A.
2 T ag all the parts you must remove and retain to make the subsequent
installation easier.
(b) Remove the LH inboard flap assy, refer to Ref. MP A350-A-57-54-62-00ZZZ-520Z-
A:
NOTE: Make sure that the removed LH inboard flap assy, item (1), the threaded
sleeve, item (8) and the slide ring, item (10) are sent back to AIRBUS.
1 FLAP ASSY-INBOARD WQ209AQAAAAA Item (1) Discard
OR
1 FLAP ASSY-INBOARD WQ209BDAAAAA Item (1) Discard
attached with:
1 WASHER   Item (3) Retain
1 WASHER-KEY   Item (4) Discard
1 NUT-SPANNER   Item (5) Retain
1 WASHER-LOCKING   Item (6) Discard
2 NUT   Item (7) Discard
1 THREADED SLEEVE   Item (8) Discard
1 WASHER   Item (9) Discard
1 SLIDE RING   Item (10) Discard
1 LOCKING DEVICE   Item (11) Retain
1 COTTER PIN   Item (12) Discard
1 NUT   Item (13) Discard
1 WASHER   Item (14) Discard
4 BOLT   Item (15) Retain
4 WASHER   Item (16) Retain
3 BOLT   Item (17) Discard
3 WASHER   Item (16) Discard
3 NUT   Item (18) Discard
1 BOLT   Item (19) Retain
1 RETAINER   Item (20) Retain

### Page 24

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 24
1 WASHER   Item (21) Retain
1 WASHER-KEY   Item (22) Discard
1 NUT-SPANNER   Item (23) Retain
1 BOLT   Item (24) Retain
1 WASHER   Item (25) Retain
1 BUSH-SLIDING   Item (26) Retain
1 WASHER   Item (27) Retain
1 NUT-12 POINT   Item (28) Retain
1 CAP-LOCKING   Item (29) Retain
1 COTTER PIN   Item (30) Discard
1 BUSH SHEAR SLAVE   Item (31) Retain
1 BUSH SHEAR MASTER   Item (32) Retain
2 PLATE-LOCKING   Item (33) Discard
1 PLATE-LOCKING   Item (34) Discard
1 PLATE-LOCKING   Item (35) Discard
8 SCREW   Item (36) Discard
3 CAP-BLANKING   Item (38) Discard
3 PLASTIC PLUG   Item (39) Retain
NOTE: Parts mentioned above are just a list of which parts must be retained or
discarded, refer to Ref. Fig.BA Removal of the LH Inboard Flap Assy.

### Page 25

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-0772J-A-001-01 Fig.BA Sol.AA SHEET 1/4
REV 00 Feb 05/24 A350-57-P090Removal of the LH Inboard Flap Assy
Page 25
CONF 001
B
(1)
F
Z561
A B
A
(1)
C
J
E
G
J
H
ICN-A350-A-57XXP090-A-FAPE3-0772J-A-001-01

### Page 26

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-0772K-A-001-01 Fig.BA Sol.AA SHEET 2/4
REV 00 Feb 05/24 A350-57-P090Removal of the LH Inboard Flap Assy
Page 26
CONF 001
(22)
(21)
(20)
(23)
(19)
(17)
(16)
(18)
D
(1)
C(8)
(3)
(4)
(5)
(6)
(7)
(9)
(10)
(12)(13)
(15) (16)
(11)
(14) (7)
D
(1)
NOTE:
THIS FIGURE IS FOR IDENTIFICATION OF THE REMOVED PARTS ONLY.
ICN-A350-A-57XXP090-A-FAPE3-0772K-A-001-01

### Page 27

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-0772L-A-002-01 Fig.BA Sol.AA SHEET 3/4
REV 00 Feb 05/24 A350-57-P090Removal of the LH Inboard Flap Assy
Page 27
CONF 001
(30)
(25)
(24)
(26)(27)
(28)
(29)
E
(1)
F
(17)
(16)(17)
(1)
(16)
(18)
NOTE:
THIS FIGURE IS FOR IDENTIFICATION OF THE REMOVED PARTS ONLY.
ICN-A350-A-57XXP090-A-FAPE3-0772L-A-002-01

### Page 28

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-0772M-A-003-01 Fig.BA Sol.AA SHEET 4/4
REV 00 Feb 05/24 A350-57-P090Removal of the LH Inboard Flap Assy
Page 28
CONF 001
J
TYPICAL VIEW
(39)
(38)
(1)
G
(33)
(36)
(31)
(1)
(34)
(36) 01
01
01
01
H
(33)
(36)
(32)
(1)
(35)
(36)
01
01
01
01
NOTE:
THIS FIGURE IS FOR IDENTIFICATION OF THE REMOVED PARTS ONLY. 
01 REMOVE LOCKWIRE.
ICN-A350-A-57XXP090-A-FAPE3-0772M-A-003-01

### Page 29

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 29
CONF 002
(1) Task A350-A-57-XX-P090-01002-520A-A (A350-A-57-XX-P090-01ZZZ-520Z-A)
Remove the LH Inboard Flap Assy
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
561
Manpower/Resources/Skills
Man-hours 18.00 h
Minimum Number of person 3
Elapsed Time 6.00 h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-57-54-62-00ZZZ-520Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-04CZ-A.
2 T ag all the parts you must remove and retain to make the subsequent
installation easier.
(b) Remove the LH inboard flap assy, refer to Ref. MP A350-A-57-54-62-00ZZZ-520Z-
A:
NOTE: Make sure that the removed LH inboard flap assy, item (1) and the
threaded sleeve, item (7) are sent back to AIRBUS.
1 FLAP ASSY-INBOARD WQ209ATAAAAA Item (1) Discard
OR
1 FLAP ASSY-INBOARD WQ209AYAAAAA Item (1) Discard
OR
1 FLAP ASSY-INBOARD WQ209AZAAAAA Item (1) Discard
attached with:
1 WASHER   Item (3) Retain
1 WASHER-KEY   Item (4) Discard
1 NUT-SPANNER   Item (5) Retain
1 WASHER-LOCKING   Item (6) Retain
1 THREADED SLEEVE   Item (7) Discard
1 WASHER   Item (63) Discard
1 NUT   Item (9) Retain

### Page 30

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 30
1 SLIDE RING   Item (10) Retain
1 SCREW   Item (11) Discard
1 WASHER-LOCKING   Item (12) Retain
4 BOLT   Item (13) Retain
4 WASHER   Item (14) Retain
1 LOCKING DEVICE   Item (15) Retain
1 BOLT   Item (17) Retain
3 BOLT   Item (18) Retain
6 WASHER   Item (19) Retain
3 NUT   Item (71) Discard
1 RETAINER   Item (21) Retain
1 WASHER-KEY   Item (22) Discard
1 WASHER   Item (23) Retain
1 NUT-SPANNER   Item (24) Retain
1 BOLT   Item (25) Retain
1 WASHER   Item (26) Retain
1 BUSH-SLIDING   Item (27) Retain
1 WASHER   Item (28) Retain
1 NUT-12 POINT   Item (29) Retain
1 COTTER PIN   Item (30) Discard
1 CAP-LOCKING   Item (31) Retain
1 BUSH SHEAR SLAVE   Item (32) Retain
1 BUSH SHEAR MASTER   Item (33) Retain
1 PLATE-LOCKING   Item (34) Retain
1 PLATE-LOCKING   Item (35) Retain
2 PLATE-LOCKING   Item (36) Retain
8 SCREW   Item (37) Discard
3 CAP-BLANKING   Item (38) Discard
3 PLASTIC PLUG   Item (39) Retain
NOTE: Parts mentioned above are just a list of which parts must be retained or
discarded, refer to Ref. Fig.BA Removal of the LH Inboard Flap Assy.

### Page 31

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-07730-A-001-01 Fig.BA Sol.AB SHEET 1/4
REV 00 Feb 05/24 A350-57-P090Removal of the LH Inboard Flap Assy
Page 31
CONF 002
B
(1)
F
Z561
A B
A
(1)
C
J
E
G
J
H
ICN-A350-A-57XXP090-A-FAPE3-07730-A-001-01

### Page 32

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-07731-A-003-01 Fig.BA Sol.AB SHEET 2/4
REV 00 Feb 05/24 A350-57-P090Removal of the LH Inboard Flap Assy
Page 32
CONF 002
D
C(7)
(3)
(4)
(5)
(6)
(63)
(10)
(13) (14)
(15)
(9)
D
(1)
(11)
(12)
(22)
(23)
(21)
(24)
(17)
(18)
(19)
(71)
(1)
(19)
NOTE:
THIS FIGURE IS FOR IDENTIFICATION OF THE REMOVED PARTS ONLY.
REMOVE LOCKWIRE.01
01
01
ICN-A350-A-57XXP090-A-FAPE3-07731-A-003-01

### Page 33

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-07732-A-002-01 Fig.BA Sol.AB SHEET 3/4
REV 00 Feb 05/24 A350-57-P090Removal of the LH Inboard Flap Assy
Page 33
CONF 002
F
(18)
(19)(18)(71)
(71)
(1)
(19)
NOTE:
THIS FIGURE IS FOR IDENTIFICATION OF THE REMOVED PARTS ONLY.
(30)
(26)
(25)
(27)(28)
(29)
(31)
E
(1)
ICN-A350-A-57XXP090-A-FAPE3-07732-A-002-01

### Page 34

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-07733-A-002-01 Fig.BA Sol.AB SHEET 4/4
REV 00 Feb 05/24 A350-57-P090Removal of the LH Inboard Flap Assy
Page 34
CONF 002
J
TYPICAL VIEW
(39)
(38)
(1)
G
(36)
(37)
(32)
(1)
(34)
(37) 01
01
01
01
H
(36)
(37)
(33)
(1)
(35)
(37)
01
01
01
01
NOTE:
THIS FIGURE IS FOR IDENTIFICATION OF THE REMOVED PARTS ONLY. 
01 REMOVE LOCKWIRE.
ICN-A350-A-57XXP090-A-FAPE3-07733-A-002-01

### Page 35

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 35
CONF ALL
(2) Task A350-A-57-XX-P090-02001-920A-C (A350-A-57-XX-P090-02ZZZ-920Z-C)
Modify the New LH Inboard Flap Assy on Bench
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
04DCA3
Primer Epoxy Paint - Low
VOC Chromate Free -
External Structure
04PAC2 Polyurethane Coating - -Wear ResistantStructure
04SBA3 Varnish Polyurethane - LowVOC - External Structure
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
1 WQ209CBAAAAA 1 FLAP
58 ABS0970-72 1 PLATE (1)
NOTE(S)
(1): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.
Re-identified Part Set
ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
1 WQ209A1AAACW FLAP (1) WQ209CBAAAAA
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-42-XX-01ZZZ-667Z-AA350-A-51-75-12-00ZZZ-660Z-A
MP A350-A-11-XX-XX-00ZZZ-691Z-A
CML CONSUMABLE MATERIAL LIST (CML)
PMS 01-06-12
Procedure
Ref. Fig.BB Modification of the New LH Inboard Flap Assy on Bench
(a) Standard practices given in this procedure:

### Page 36

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 36
1 Remove and install fasteners in accordance with Ref. ASR A350-A-51-42-XX-
01ZZZ-667Z-A.
2 Repair the paint coating in accordance with Ref. ASR A350-A-51-75-12-
00ZZZ-660Z-A.
3 For the installation of placards, refer to Ref. MP A350-A-11-XX-XX-00ZZZ-
691Z-A.
4 If you find process and material specifications that you do not know in
the design drawings, refer to the cross-reference list in the Process and
Material Specification (PMS).
5 For the specification of Material application codes given in this Service
Bulletin, refer to Ref. CML.
(b) Modify the new LH inboard flap assy:
1 FLAP ASSY-INBOARD WQ209CBAAAAA Item 1
WARNING: USE GOGGLES EACH TIME YOU CUT A COTTER PIN. REMOVE
AND DISCARD THE COTTER PIN IMMEDIATELY.
1 Remove the clamp and the clamp assy from the trunnion tube:
1 CLAMP   Item (50) Discard
1 CLAMP   Item (51) Discard
attached with:
4 BOLT   Item (52) Discard
8 WASHER   Item (53) Discard
4 NUT   Item (54) Discard
4 COTTER PIN   Item (55) Discard
1 RETAINER   Item (56) Discard
1 BARREL NUT   Item (57) Discard
2 Use a non-metallic scraper to remove any remaining sealant from the
trunnion tube.
3 Clean the trunnion tube with:
  T extile - Lint free Cotton14SBA1  
and
  Non Aqueous Cleaner -
General
08BAA9  
4 Check the wear resistant coating of the trunnion tube:
a If the wear resistant coating of the trunnion tube is damaged:
<1> Restore the wear resistant coating with:
  Primer Epoxy Paint -
Low VOC Chromate Free
- External Structure
04DCA3  
and

### Page 37

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 37
  Polyurethane Coating - -
Wear ResistantStructure
04PAC2  
<2> Proceed with the next step.
b If the wear resistant coating of the trunnion tube is not damaged:
<1> Proceed with the next step.
(c) Re-identify the modified LH inboard flap assy:
1 Modify the existing identification placard:
a On the existing identification placard, cross out the existing PN with
indelible ink, refer to Ref. PMS 01-06-12.
NOTE: Make sure that the existing PN is no longer readable.
b Apply surface protection to the existing placard with:
  Varnish Polyurethane
- Low VOC - External
Structure
04SBA3  
2 Install the new identification placard:
a Clean the installation area of the new placard, item 58, with:
  T extile - Lint free Cotton14SBA1  
and
  Non Aqueous Cleaner -
General
08BAA9  
b Install:
1 PLATE IDENTIFICATION ABS0970-72 Item 58
3 Re-identify the new LH inboard flap assy, by writing with indelible ink the
new PN in the new label, item 58, refer to Ref. PMS 01-06-12.
a After the modification:
1 FLAP ASSY-INBOARD WQ209CBAAAAA Item (1)  
becomes:
1 FLAP ASSY-INNER,LH WQ209A1AAACW Item 1
4 Apply surface protection to the new identification placard, item 58, with:
  Varnish Polyurethane
- Low VOC - External
Structure
04SBA3

### Page 38

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-0772N-A-001-01 Fig.BB Sol.AA SHEET 1/2
REV 00 Feb 05/24 A350-57-P090Modification of the New LH Inboard Flap Assy on Bench
Page 38
CONF ALL
01
02
NOTE:
APPLY SURFACE PROTECTION WITH MATERIAL No 04SBA3.
03 IF NECESSARY, RESTORE THE WEAR RESISTANT COATING WITH MATERIAL
No 04DCA3 AND MATERIAL No 04PAC2.
A
B
EXISTING LABEL
C
TRUNNION BAR
0201
03
CROSS OUT THE EXISTING PART NUMBER WITH INDELIBLE INK AS PER PMS 01-06-12.
1
A
ON BENCH
ICN-A350-A-57XXP090-A-FAPE3-0772N-A-001-01

### Page 39

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-0772O-A-001-01 Fig.BB Sol.AA SHEET 2/2
REV 00 Feb 05/24 A350-57-P090Modification of the New LH Inboard Flap Assy on Bench
Page 39
CONF ALL
B
(50)
(51)
(55)
(54)
(53)
(53)
(54)
(55)
(53)
(52)
(52)
(53)
(57)
(56)
A/C :
MFR
DMF
SER
Production Data
INSPECT
PNR/CA CODE:
DESCR. :
Spare Data
PNR
DESCR. :
INSPECT
ABS0970-72
58
C
APPLY SURFACE PROTECTION WITH MATERIAL No 04SBA3.02
NOTE:
02
ICN-A350-A-57XXP090-A-FAPE3-0772O-A-001-01

### Page 40

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 40
CONF 001
(3) Task A350-A-57-XX-P090-01001-720A-A (A350-A-57-XX-P090-01ZZZ-720Z-A)
Install the LH Inboard Flap Assy
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
561
Manpower/Resources/Skills
Man-hours 24.00 h
Minimum Number of person 3
Elapsed Time 8.00 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
14QFC1 Wire - Locking Dia: 0.8 mmCRES
Part kit 57P090D02R00
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
4 ABS1149AP2375B 1 WASHER
22 ABS1149AP1125B 1 WASHER
30 MS24665-155 1 PIN
61 V5759136020200 1 WASHER
62 V5759136620200 1 SLEEVE
63 V5759136320200 1 WASHER
64 V5759136220200 1 NUT
65 V5759136120200 1 RING
66 ABS1830L8A44 1 BOLT
67 V5759136720000 1 WASHER
69 ABS0114T4-4 3 BOLT
70 NSA5379-4CK 6 WASHER
71 NAS1726C4PE 3 NUT
72 ABS1830L10A40 8 BOLT
73 V5759137420200 2 PLATE
74 V5759137520200 1 PLATE
75 V5759137520300 1 PLATE
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
38 ASNA2879E050 3 CAP (1)
NOTE(S)

### Page 41

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 41
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
(1): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.
Re-identified Part Set
ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
1 WQ209A1AAACW FLAP (1) WQ209CBAAAAA
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-43-XX-01ZZZ-667Z-A
MP A350-A-57-54-62-00ZZZ-720Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
CML CONSUMABLE MATERIAL LIST (CML)
Procedure
(a) Standard practices given in this procedure:
1 For identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-04CZ-A.
2 Get alternative and substitute fastener data in accordance with Ref. ASR
A350-A-51-43-XX-01ZZZ-667Z-A.
3 For the specification of Material application codes given in this Service
Bulletin, refer to Ref. CML.
(b) Install the new LH inboard flap assy, refer to Ref. MP A350-A-57-54-62-00ZZZ-
720Z-A.
1 FLAP ASSY-INNER,LH WQ209A1AAACW Item 1
with:
1 WASHER   Item (3) Retained
1 WASHER-KEY ABS1149AP2375B Item 4
1 NUT-SPANNER   Item (5) Retained
1 WASHER-LOCKING V5759136020200 Item 61
1 SLEEVE V5759136620200 Item 62
1 WASHER V5759136320200 Item 63
1 NUT V5759136220200 Item 64
1 SLIDE RING V5759136120200 Item 65
1 BOLT ABS1830L8A44 Item 66
1 WASHER-LOCKING V5759136720000 Item 67
1 LOCKING DEVICE   Item (11) Retained
4 BOLT   Item (15) Retained
4 WASHER   Item (16) Retained

### Page 42

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 42
3 BOLT ABS0114T4-4 Item 69
6 WASHER NSA5379-4CK Item 70
3 NUT NAS1726C4PE Item 71
1 BOLT   Item (19) Retained
1 RETAINER   Item (20) Retained
1 WASHER   Item (21) Retained
1 WASHER-KEY ABS1149AP1125B Item 22
1 NUT-SPANNER   Item (23) Retained
1 BOLT   Item (24) Retained
1 WASHER   Item (25) Retained
1 BUSH-SLIDING   Item (26) Retained
1 WASHER   Item (27) Retained
1 NUT-12 POINT   Item (28) Retained
1 CAP-LOCKING   Item (29) Retained
1 PIN-COTTER MS24665-155 Item 30
1 SHEAR BUSH   Item (31) Retained
1 SHEAR BUSH   Item (32) Retained
8 BOLT ABS1830L10A40 Item 72
2 PLATE-LOCKING V5759137420200 Item 73
1 PLATE-LOCKING V5759137520200 Item 74
1 PLATE-LOCKING V5759137520300 Item 75
  Wire - Locking Dia: 0.8
mm CRES
14QFC1  
3 CAP-BLANKING ASNA2879E050 Item 38
3 PLASTIC PLUG   Item (39) Retained
NOTE: Parts mentioned above are just an indication of which parts must be
installed new or retained, refer to Ref. Fig.BC Installation of the LH
Inboard Flap Assy.

### Page 43

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-0772P-A-001-01 Fig.BC Sol.AA SHEET 1/4
REV 00 Feb 05/24 A350-57-P090Installation of the LH Inboard Flap Assy
Page 43
CONF 001
B
1
F
Z561
A B
A
1
C
J
J E
G
H
ICN-A350-A-57XXP090-A-FAPE3-0772P-A-001-01

### Page 44

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-0772Q-A-001-01 Fig.BC Sol.AA SHEET 2/4
REV 00 Feb 05/24 A350-57-P090Installation of the LH Inboard Flap Assy
Page 44
CONF 001
D
C62
(3)
4
(5)
61
63
65
(15) (16)
(11)
64
D
1
66
67
22
(21)
(20)
(23)
(19)
69
70
71
1
70
NOTE:
THIS FIGURE IS FOR IDENTIFICATION OF THE INSTALLED PARTS ONLY.
01 SECURE WITH LOCKWIRE.
01
01
ICN-A350-A-57XXP090-A-FAPE3-0772Q-A-001-01

### Page 45

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-0772R-A-002-01 Fig.BC Sol.AA SHEET 3/4
REV 00 Feb 05/24 A350-57-P090Installation of the LH Inboard Flap Assy
Page 45
CONF 001
F
69
70 6971
71
1
70
THIS FIGURE IS FOR IDENTIFICATION OF THE INSTALLED PARTS ONLY.
NOTE:
30
(25)
(24)
(26)(27)
(28)
(29)
E
1
ICN-A350-A-57XXP090-A-FAPE3-0772R-A-002-01

### Page 46

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-0772S-A-003-01 Fig.BC Sol.AA SHEET 4/4
REV 00 Feb 05/24 A350-57-P090Installation of the LH Inboard Flap Assy
Page 46
CONF 001
J
TYPICAL VIEW
(39)
38
1
G
73
72
(31)
1
74
72 01
01
01
01
H
73
72
(32)
1
75
72
01
01
01
01
NOTE:
THIS FIGURE IS FOR IDENTIFICATION OF THE INSTALLED PARTS ONLY.
01 SECURE WITH LOCKWIRE.
ICN-A350-A-57XXP090-A-FAPE3-0772S-A-003-01

### Page 47

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 47
CONF 002
(3) Task A350-A-57-XX-P090-01002-720A-A (A350-A-57-XX-P090-01ZZZ-720Z-A)
Install the LH Inboard Flap Assy
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
561
Manpower/Resources/Skills
Man-hours 24.00 h
Minimum Number of person 3
Elapsed Time 8.00 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
14QFC1 Wire - Locking Dia: 0.8 mmCRES
Part kit 57P090D03R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
4 ABS1149AP2375B 1 WASHER
22 ABS1149AP1125B 1 WASHER
30 MS24665-155 1 PIN
62 V5759136620200 1 SLEEVE
63 V5759136320200 1 WASHER
66 ABS1830L8A44 1 BOLT
71 NAS1726C4PE 3 NUT
72 ABS1830L10A40 8 BOLT
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
38 ASNA2879E050 3 CAP (1)
NOTE(S)
(1): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.
Re-identified Part Set
ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
1 WQ209A1AAACW FLAP (1) WQ209CBAAAAA
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-43-XX-01ZZZ-667Z-A
MP A350-A-57-54-62-00ZZZ-720Z-A

### Page 48

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 48
Manuals/Drawings References/Sheets
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
CML CONSUMABLE MATERIAL LIST (CML)
Procedure
(a) Standard practices given in this procedure:
1 For identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-04CZ-A.
2 Get alternative and substitute fastener data in accordance with Ref. ASR
A350-A-51-43-XX-01ZZZ-667Z-A.
3 For the specification of Material application codes given in this Service
Bulletin, refer to Ref. CML.
(b) Install the new LH inboard flap assy, refer to Ref. MP A350-A-57-54-62-00ZZZ-
720Z-A.
1 FLAP ASSY-INNER,LH WQ209A1AAACW Item 1
with:
1 WASHER   Item (3) Retained
1 WASHER-KEY ABS1149AP2375B Item 4
1 NUT-SPANNER   Item (5) Retained
1 WASHER-LOCKING   Item (6) Retained
1 SLEEVE V5759136620200 Item 62
1 WASHER V5759136320200 Item 63
1 NUT   Item (9) Retained
1 SLIDE RING   Item (10) Retained
1 BOLT ABS1830L8A44 Item 66
1 WASHER-LOCKING   Item (12) Retained
4 BOLT   Item (13) Retained
4 WASHER   Item (14) Retained
1 LOCKING DEVICE   Item (15) Retained
1 BOLT   Item (17) Retained
3 BOLT   Item (18) Retained
6 WASHER   Item (19) Retained
3 NUT NAS1726C4PE Item 71
1 RETAINER   Item (21) Retained
1 WASHER-KEY ABS1149AP1125B Item 22
1 WASHER   Item (23) Retained
1 NUT-SPANNER   Item (24) Retained

### Page 49

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 49
1 BOLT   Item (25) Retained
1 WASHER   Item (26) Retained
1 BUSH-SLIDING   Item (27) Retained
1 WASHER   Item (28) Retained
1 NUT-12 POINT   Item (29) Retained
1 PIN-COTTER MS24665-155 Item 30
1 CAP-LOCKING   Item (31) Retained
1 BUSH SHEAR SLAVE   Item (32) Retained
1 BUSH SHEAR MASTER   Item (33) Retained
1 PLATE-LOCKING   Item (34) Retained
1 PLATE-LOCKING   Item (35) Retained
2 PLATE-LOCKING   Item (36) Retained
8 BOLT ABS1830L10A40 Item 72
  Wire - Locking Dia: 0.8
mm CRES
14QFC1  
3 CAP-BLANKING ASNA2879E050 Item 38
3 PLASTIC PLUG   Item (39) Retained
NOTE: Parts mentioned above are just an indication of which parts must be
installed new or retained, refer to Ref. Fig.BC Installation of the LH
Inboard Flap Assy.

### Page 50

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-07734-A-001-01 Fig.BC Sol.AB SHEET 1/4
REV 00 Feb 05/24 A350-57-P090Installation of the LH Inboard Flap Assy
Page 50
CONF 002
B
1
F
Z561
A B
A
1
C
J
E
G
J
H
ICN-A350-A-57XXP090-A-FAPE3-07734-A-001-01

### Page 51

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-07735-A-003-01 Fig.BC Sol.AB SHEET 2/4
REV 00 Feb 05/24 A350-57-P090Installation of the LH Inboard Flap Assy
Page 51
CONF 002
D
C
62
(3)
4
(5)
(6)
63
(10)
(13) (14)
(15)
(9)
D
1
66
(12)
22
(23)
(21)
(24)
(17)
(18)
(19)
71
1
(19)
NOTE:
THIS FIGURE IS FOR IDENTIFICATION OF THE INSTALLED PARTS ONLY.
SECURE WITH LOCKWIRE.01
01
01
ICN-A350-A-57XXP090-A-FAPE3-07735-A-003-01

### Page 52

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-07736-A-002-01 Fig.BC Sol.AB SHEET 3/4
REV 00 Feb 05/24 A350-57-P090Installation of the LH Inboard Flap Assy
Page 52
CONF 002
F
(18)
(19)(18)71
71
1
(19)
NOTE:
THIS FIGURE IS FOR IDENTIFICATION OF THE INSTALLED PARTS ONLY.
30
(26)
(25)
(27)(28)
(29)
(31)
E
1
ICN-A350-A-57XXP090-A-FAPE3-07736-A-002-01

### Page 53

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP090-A-FAPE3-07737-A-003-01 Fig.BC Sol.AB SHEET 4/4
REV 00 Feb 05/24 A350-57-P090Installation of the LH Inboard Flap Assy
Page 53
CONF 002
J
TYPICAL VIEW
(39)
38
1
G
(36)
72
(32)
1
(34)
72 01
01
01
01
H
(36)
72
(33)
1
(35)
72
01
01
01
01
NOTE:
THIS FIGURE IS FOR IDENTIFICATION OF THE INSTALLED PARTS ONLY.
01 SECURE WITH LOCKWIRE.
ICN-A350-A-57XXP090-A-FAPE3-07737-A-003-01

### Page 54

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 54
CONF ALL
D. PREPARATION FOR TEST
(1) Task A350-A-57-XX-P090-01001-900A-A (A350-A-57-XX-P090-01ZZZ-900Z-A)
Preparation for Test
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 1.50 h
Minimum Number of person 3
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-57-54-62-00ZZZ-720Z-A
Procedure
(a) Remove the safety clips and tags and close the circuit breakers as specified in
the installation of the LH inboard flap assy, refer to Ref. MP A350-A-57-54-62-
00ZZZ-720Z-A.
(b) Do the preparation of test as specified in the installation of the LH inboard flap
assy, refer to Ref. MP A350-A-57-54-62-00ZZZ-720Z-A.
E. TEST
(1) Task A350-A-57-XX-P090-01001-300A-A (A350-A-57-XX-P090-01ZZZ-300Z-A)
Test
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 1.50 h
Minimum Number of person 3
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-57-54-62-00ZZZ-720Z-AA350-A-57-57-61-00ZZZ-720Z-A
SD A350-A-06-4X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practice given in this procedure:
1 For the identification of access panels, refer to Ref. SD A350-A-06-4X-XX-
01ZZZ-04CZ-A.
(b) Do the adjustments and test procedures as specified in the installation of the LH
inboard flap assy, refer to Ref. MP A350-A-57-54-62-00ZZZ-720Z-A.
(c) T est of access Panel 531AB:

### Page 55

A350
SERVICE BULLETIN
REV 00 Feb 05/24 A350-57-P090
Page 55
1 Do the test procedure as specified in the installation of the fixed fairing
assembly 531AB, refer to Ref. MP A350-A-57-57-61-00ZZZ-720Z-A.
F. CLOSE-UP
(1) Task A350-A-57-XX-P090-01001-740A-A (A350-A-57-XX-P090-01ZZZ-740Z-A)
Close-Up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 9.00 h
Minimum Number of person 3
Elapsed Time 3.00 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-57-54-62-00ZZZ-720Z-A
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Do the close-up procedure as specified in the installation of the LH inboard flap
assy, refer to Ref. MP A350-A-57-54-62-00ZZZ-720Z-A.
(c) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A350-A-57-XX-P090-01001-90AA-A (A350-A-57-XX-P090-01ZZZ-90AZ-A)
Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 56

A350
SERVICE BULLETIN
APPENDIX
REV 00 Feb 05/24 A350-57-P090
Page 56
APPENDIX
A. REPORTING SHEET
TITLE: WINGS - INBOARD FLAP - INTRODUCE REPLACEMENT LH INBOARD
FLAP FOLLOWING INSPECTION FINDING ON TRUNNION (SB ONLY)
MODIFICATION No.: 120317L01293
(1) SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance
and Flight Operations Products if it is duly reported to Airbus.
(2) GENERAL information
The SB Reporting policy is published in ISI 00.00.00135. This document provides
information regarding: the SB Reporting means and benefits, the update of
customized Maintenance Products and customized Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations
Products" for further information on the update of affected Flight Operations Products.
(3) SB Reporting procedure
Standard practice to report SB is to use the online reporting application on
AirbusWorld.
Refer to ISI 00.00.00179:
- For complete information on reporting means to Airbus, Question 2 "What are
the standard practices for SB Reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs,
Question 3 "What about the reporting of prerequisite Service Bulletins?"
NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.

### Page 57

A350
SERVICE BULLETIN
APPENDIX
REV 00 Feb 05/24 A350-57-P090
Page 57
B. QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin.
The reported data that you provide us will be used to analyse areas of difficulties and to
take corrective action to further improve the quality of our Service Bulletin.
We thank you for the time you have taken in completing this form.
Quality rating of this SB 4 3 2 1
Quality rating of the Accomplishment Instructions 4 3 2 1
Quality rating of the Illustrations 4 3 2 1
Is this SB easy to understand ? Y / N
NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score
If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.
Planning Material Instructions
X Applicability X T ooling X Preparation
X Reason X List of Materials
Operator Supplied
X Mod/Inspection
X Manpower X Kit content X T est
X References X Re-identification X Close-up
X Publication X Illustrations
X Industry Support
Comments :
Operator : Date :
Name/Title
Please return this form to :
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
Or via your Resident Customer Support Office.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
