# Airbus Service Bulletin A350-57-P091

Copy: No revision named ("A350-57-P091"), 47 pages: PDF https://openairdocs.org/files/sha256/b0/55/b0550c42351fd517f69053822214b9c15a578e418e85ed9c6e4b79a7c866cee7; text https://openairdocs.org/service-documents/airbus/a350-57-p091/file/b0550c42351f.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2025-0340; AD 2025-20-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A350-57-P091
- Page: https://openairdocs.org/service-documents/airbus/a350-57-p091

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2025-20-05](https://openairdocs.org/ad/2025-20-05.md), effective Dec 30, 2025: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus/a350-57-p091/proposed.md).

## Text (47 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2025-0340; AD 2025-20-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 1
CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
 
The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.
MANDATORY MANDATORY MANDATORY
ATA SYSTEM: 57
TITLE: WINGS - CENTER WING - RIB1 CORNER FITTING MISSING EDGE GLOW
SEALANT
MODIFICATION No.:
None

### Page 2

A350
SERVICE BULLETIN
SUMMARY
REV 00 May 30/24 A350-57-P091
Page 2
ATA SYSTEM: 57
TITLE: WINGS - CENTER WING - RIB1 CORNER FITTING MISSING EDGE GLOW
SEALANT
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR None
MINOR None
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
B. REASON
(1) History
It has been identified that sealant may not have been applied correctly to all required
locations at the corner fittings Rib 1, installed at the front and rear spar positions, top
and bottom skin. The sealant provides the second layer of protection to prevent front
spar or rear spar corner fittings glow in case of lighting strike.
(2) Objective/Action
A one-time detailed inspection of the sealant application is required to identify and
restore any areas of missing sealant in accordance with drawing requirements.
(3) Advantages
Correction of any missing sealant will restore the 2 independent layers of lightning
strike protection in accordance with the certification requirement.
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE MANDATORY COST SAVING NO
A/C OPERATION
AFFECTED
NO VENDOR SB NO
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD YES
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO
NOTE: Service Bulletin must be accomplished.
D. MAINTENANCE CONFIGURATION

### Page 3

A350
SERVICE BULLETIN
SUMMARY
REV 00 May 30/24 A350-57-P091
Page 3
MAINTENANCE CONFIGURATION
FUEL TANKS OPENED YES
E. MATERIAL PRICE INFORMATION
(1) Detailed Inspection of the Edge Glow Sealant on the Corner Fittings at RIB 1
(a) T ask set A350-A-57-XX-P091-01000-93BA-A Detailed Inspection of the Edge Glow
Sealant on the Corner Fittings at RIB 1
No material
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
AAR AFL AFR BAW CAL CCA CES CPA CSC CSN DAL DLH EDW ETD ETH EVE FBU FIN FJI FWI
GAF HVN IBE ITY JAL KAY MAS MAU PAL QTR SAS SIA SJX THA THY VIR WFL
G. CONCURRENT REQUIREMENTS
None
H. NATURE OF THE WORK
(1) Detailed Inspection of the Edge Glow Sealant on the Corner Fittings at RIB 1
(a) T ask set A350-A-57-XX-P091-01000-93BA-A Detailed Inspection of the Edge Glow
Sealant on the Corner Fittings at RIB 1
AIRCRAFT YES
EQUIPMENT NO
I. MANPOWER
(1) Detailed Inspection of the Edge Glow Sealant on the Corner Fittings at RIB 1
(a) T ask set A350-A-57-XX-P091-01000-93BA-A Detailed Inspection of the Edge Glow
Sealant on the Corner Fittings at RIB 1
MANPOWER
TOTAL MAN-HOURS 34.00 h
ELAPSED TIME (HOURS) 17.00 h

### Page 4

A350
SERVICE BULLETIN
SUMMARY
Figure ICN-A350-A-57XXP091-A-FAPE3-07A70-A-001-01 Fig.SA Sol.AA SHEET 1/1
REV 00 May 30/24 A350-57-P091General Overview
Page 4
J. GENERAL OVERVIEW
CONF ALL
BZ641
Z541 LH
RH
A
A
LH SHOWN 
RH SYMMETRICAL
RIB1 RIB2
RIB1
RIB2
RIB 1 CORNER FITTINGS TO BE INSPECTED
NOTE:
B
RIB1
LH SHOWN 
RH SYMMETRICAL
ICN-A350-A-57XXP091-A-FAPE3-07A70-A-001-01

### Page 5

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 5
ATA SYSTEM: 57
TITLE: WINGS - CENTER WING - RIB1 CORNER FITTING MISSING EDGE GLOW
SEALANT
1. PLANNING INFORMATION
A. APPLICABILITY
NOTE: RDAF 81339801/006/2024 is issued to perform the inspection on aircraft with
Manufacturer Serial Numbers (MSN)s 0220, 0223, 0230 and 0232 before publication
of this Service Bulletin.
(1) Models
ON A/C 0065, 0071, 0088, 0102, 0110, 0118, 0125, 0141, 0161, 0169, 0188, 0206, 0215,
0225, 0229, 0233, 0241, 0252, 0258, 0262, 0266, 0274, 0286, 0290, 0296, 0298, 0306,
0315, 0319, 0326, 0330, 0332, 0336, 0340, 0342, 0346, 0350, 0356, 0362, 0368, 0372,
0374, 0380, 0382, 0386, 0388, 0399, 0402, 0415, 0420, 0424, 0426, 0432, 0434, 0440,
0446, 0473, 0482, 0490, 0492, 0495, 0503, 0507, 0509, 0533, 0539, 0547, 0560, 0563, 0584
350-1041
ON A/C 0005-0058, 0060-0064, 0066-0070, 0072-0087, 0089-0101, 0103-0107, 0109, 0111-
0117, 0119-0124, 0126-0130, 0132-0138, 0140, 0142-0151, 0153-0155, 0157-0160, 0162-
0165, 0167, 0168, 0170, 0172-0187, 0189-0193, 0195-0205, 0207-0214, 0216-0221, 0223,
0224, 0226-0228, 0230-0232, 0234-0240, 0243-0251, 0254-0257, 0259-0261, 0263-0265,
0267-0273, 0276-0285, 0287, 0289, 0291-0295, 0297, 0299-0303, 0305, 0307-0314, 0316,
0318, 0320-0325, 0327-0329, 0331, 0333-0335, 0337-0339, 0341, 0343-0345, 0347-0349,
0351, 0352, 0354, 0355, 0357-0359, 0363-0366, 0369-0371, 0373, 0375, 0376, 0378, 0379,
0381, 0383, 0385, 0387, 0389-0398, 0400, 0401, 0403-0408, 0410-0414, 0416-0419, 0421-
0423, 0425, 0427-0429, 0431, 0433, 0435-0437, 0439, 0441-0443, 0445, 0447-0449, 0451-
0455, 0457-0460, 0462-0466, 0468-0472, 0474-0476, 0478-0481, 0483-0485, 0487-0489,
0491, 0493, 0494, 0496, 0497, 0499, 0500, 0502, 0504-0506, 0510, 0512, 0516, 0517, 0520,
0524, 0526, 0528, 0530, 0531, 0535-0537, 0540-0546, 0548-0552, 0556, 0557, 0559, 0561,
0562, 0564, 0565, 0567-0570, 0572-0574, 0576, 0578-0580, 0582, 0583, 0588, 0593, 0596,
0599
350-941
CONF ALL
(2) Applicability by MSN
0005-0058 0060-0107 0109-0130 0132-0138 0140-0151 0153-0155 0157-0165 0167-
0170 0172-0193 0195-0221 0223-0241 0243-0252 0254-0274 0276-0287 0289-0303
0305-0316 0318-0352 0354-0359 0362-0366 0368-0376 0378-0383 0385-0408 0410-
0429 0431-0437 0439-0443 0445-0449 0451-0455 0457-0460 0462-0466 0468-0476
0478-0485 0487-0497 0499 0500 0502-0507 0509 0510 0512 0516 0517 0520 0524
0526 0528 0530 0531 0533 0535-0537 0539-0552 0556 0557 0559-0565 0567-0570
0572-0574 0576 0578-0580 0582-0584 0588 0593 0596 0599
(3) MSN by configuration
MSN CONFIGURATION
0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015
0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026
0027 0028 0029 0030 0031 0032 0033 0034 0035 0036 0037
0038 0039 0040 0041 0042 0043 0044 0045 0046 0047 0048
0049 0050 0051 0052 0053 0054 0055 0056 0057 0058 0060
0061 0062 0063 0064 0065 0066 0067 0068 0069 0070 0071
0072 0073 0074 0075 0076 0077 0078 0079 0080 0081 0082
001

### Page 6

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 6
MSN CONFIGURATION
0083 0084 0085 0086 0087 0088 0089 0090 0091 0092 0093
0094 0095 0096 0097 0098 0099 0100 0101 0102 0103 0104
0105 0106 0107 0109 0110 0111 0112 0113 0114 0115 0116
0117 0118 0119 0120 0121 0122 0123 0124 0125 0126 0127
0128 0129 0130 0132 0133 0134 0135 0136 0137 0138 0140
0141 0142 0143 0144 0145 0146 0147 0148 0149 0150 0151
0153 0154 0155 0157 0158 0159 0160 0161 0162 0163 0164
0165 0167 0168 0169 0170 0172 0173 0174 0175 0176 0177
0178 0179 0180 0181 0182 0183 0184 0185 0186 0187 0188
0189 0190 0191 0192 0193 0195 0196 0197 0198 0199 0200
0201 0202 0203 0204 0205 0206 0207 0208 0209 0210 0211
0212 0213 0214 0215 0216 0217 0218 0219 0220 0221 0223
0224 0225 0226 0227 0228 0229 0230 0231 0232 0233 0234
0235 0236 0237 0238 0239 0240 0241 0243 0244 0245 0246
0247 0248 0249 0250 0251 0252 0254 0255 0256 0257 0258
0259 0260 0261 0262 0263 0264 0265 0266 0267 0268 0269
0270 0271 0272 0273 0274 0276 0277 0278 0279 0280 0281
0282 0283 0284 0285 0286 0287 0289 0290 0291 0292 0293
0294 0295 0296 0297 0298 0299 0300 0301 0302 0303 0305
0306 0307 0308 0309 0310 0311 0312 0313 0314 0315 0316
0318 0319 0320 0321 0322 0323 0324 0325 0326 0327 0328
0329 0330 0331 0332 0333 0334 0335 0336 0337 0338 0339
0340 0341 0342 0343 0344 0345 0346 0347 0348 0349 0350
0351 0352 0354 0355 0356 0357 0358 0359 0362 0363 0364
0365 0366 0368 0369 0370 0371 0372 0373 0374 0375 0376
0378 0379 0380 0381 0382 0383 0385 0386 0387 0388 0389
0390 0391 0392 0393 0394 0395 0396 0397 0398 0399 0400
0401 0402 0403 0404 0405 0406 0407 0408 0410 0411 0412
0413 0414 0415 0416 0417 0418 0419 0420 0421 0422 0423
0424 0425 0426 0427 0428 0429 0431 0432 0433 0434 0435
0436 0437 0439 0440 0441 0442 0443 0445 0446 0447 0448
0449 0451 0452 0453 0454 0455 0457 0458 0459 0460 0462
0463 0464 0465 0466 0468 0469 0470 0471 0472 0473 0474
0475 0476 0478 0479 0480 0481 0482 0483 0484 0485 0487
0488 0489 0490 0491 0492 0493 0494 0495 0496 0497 0499
0500 0502 0503 0504 0505 0506 0507 0509 0510 0512 0516
0517 0520 0524 0526 0528 0530 0531 0533 0535 0536 0537
0539 0540 0541 0542 0543 0544 0545 0546 0547 0548 0549
0550 0551 0552 0556 0557 0559 0560 0561 0562 0563 0564
0565 0567 0568 0569 0570 0572 0573 0574 0576 0578 0579
0580 0582 0583 0584 0588 0593 0596 0599
(4) Configuration definition
Configuration 001
CONF 001 is applicable for all the aircraft affected by this Service Bulletin as a
standard configuration.
B. CONCURRENT REQUIREMENTS
None
C. REASON

### Page 7

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 7
(1) History
It has been identified that sealant may not have been applied correctly to all required
locations at the corner fittings Rib 1, installed at the front and rear spar positions, top
and bottom skin. The sealant provides the second layer of protection to prevent front
spar or rear spar corner fittings glow in case of lighting strike.
(2) Objective/Action
A one-time detailed inspection of the sealant application is required to identify and
restore any areas of missing sealant in accordance with drawing requirements.
(3) Advantages
Correction of any missing sealant will restore the 2 independent layers of lightning
strike protection in accordance with the certification requirement.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
T o accomplish this Service Bulletin it is necessary to:
(1) Detailed Inspection of the Edge Glow Sealant on the Corner Fittings at RIB 1
(a) T ask set A350-A-57-XX-P091-01000-93BA-A Detailed Inspection of the Edge Glow
Sealant on the Corner Fittings at RIB 1
1 Do a Detailed Inspection of the Corner Fittings at RIB 1, LH side
2 Do a Detailed Inspection of the Corner Fittings at RIB 1, RH side
3 Depending on the Inspection Result, Apply Sealant on the Corner Fittings at
RIB 1, LH side
4 Depending on the Inspection Result, Apply Sealant on the Corner Fittings at
RIB 1, RH side
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin must be done within the threshold given in the
table below.
This Service Bulletin has been classified Mandatory. It is expected that an
Airworthiness Directive (AD) published by the European Union Aviation Safety Agency
(EASA) will be issued to confirm this classification. It is anticipated that the AD will
confirm the thresholds given but reference should be made to the AD for confirmation
of the mandated accomplishment timescale.
T able 01, Do a Detailed Inspection of the Corner Fittings at RIB1, Left Hand (LH) side
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
All aircraft Do a detailed
inspection of the
corner fittings
at rib 1 in the
LH wing in
At the next
scheduled
maintenance
tank entry or
no later than
None None

### Page 8

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 8
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
accordance with
Ref. T ask A350-
A-57-XX-P091-
01ZZZ-300Z-A
78 months
from issuance
of Inspection
Service Bulletin
(ISB), whichever
occurs first
If the sealant is
correctly applied
on all the corner
fitting areas rib 1
No further action None None None
If the sealant
is not correctly
applied on the
corner fitting
areas rib 1
Apply sealant
on the corner
fittings in the LH
wing with Ref.
T ask A350-A-
57-XX-P091-
01ZZZ-600Z-A
Before next flight None None
  No further action None None None
T able 02, Do a Detailed Inspection of the Corner Fittings at RIB 1, Right Hand (RH) side
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
All aircraft Do a detailed
inspection of the
corner fittings
at rib 1 in the
RH wing in
accordance with
Ref. T ask A350-
A-57-XX-P091-
02ZZZ-300Z-A
At the next
scheduled
maintenance
tank entry or
no later than
78 months from
issuance of
ISB, whichever
occurs first
None None
If the sealant is
correctly applied
on all the corner
fitting areas rib 1
No further action None None None
If the sealant
is not correctly
applied on the
corner fitting
areas rib 1
Apply sealant
on the corner
fittings in the
RH wing with
Ref. T ask A350-
A-57-XX-P091-
02ZZZ-600Z-A
Before next flight None None
  No further action None None None
F. APPROVAL
The technical content of this document is approved under the authority of the Design
Organisation Approval ref. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator

### Page 9

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 9
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Detailed Inspection of the Edge Glow Sealant on the Corner Fittings at RIB 1
(a) T ask set A350-A-57-XX-P091-01000-93BA-A Detailed Inspection of the Edge Glow
Sealant on the Corner Fittings at RIB 1
PREPARATION
General Job Set-Up 0.25 h
Job Set-Up on the LH Wing 14.00 h
Job Set-Up on the RH Wing 14.00 h
PROCEDURE
Do a Detailed Inspection of the Corner Fittings at RIB 1, LH
side
1.00 h
Do a Detailed Inspection of the Corner Fittings at RIB 1, RH
side
1.00 h
Depending on the Inspection Result, Apply Sealant on the
Corner Fittings at RIB 1, LH side
0.50 h
Depending on the Inspection Result, Apply Sealant on the
Corner Fittings at RIB 1, RH side
0.50 h
PREPARATION FOR TEST
Preparation for T est 0.25 h
TEST
T est 1.50 h
CLOSE-UP
Close-up on the LH Wing 0.50 h
Close-up on the RH Wing 0.50 h
TOTAL MAN-HOURS 34.00 h
ELAPSED TIME (HOURS) 17.00 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix MANPOWER GANTT CHART.
NOTE: The minimum man-hours necessary to accomplish this Service Bulletin
are those for the Inspection. Depending on the inspection result,
additional man-hours can apply.
H. WEIGHT AND BALANCE
Not changed
I. ELECTRICAL LOAD DATA
Not changed

### Page 10

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 10
J. REFERENCES
(1) Detailed Inspection of the Edge Glow Sealant on the Corner Fittings at RIB 1
(a) T ask set A350-A-57-XX-P091-01000-93BA-A Detailed Inspection of the Edge Glow
Sealant on the Corner Fittings at RIB 1
AIRCRAFT STRUCTURAL REPAIR (ASR)
A350-A-51-24-XX-01ZZZ-667Z-A A350-A-51-76-12-00ZZZ-660Z-A
CONSUMABLE MATERIAL LIST (CML)
See manual
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
INTRODUCTION (INTRO)
A350-A-00-61-04-11ZZZ-018Z-D
MAINTENANCE PROCEDURE (MP)
A350-A-24-41-XX-00ZZZ-170Z-A A350-A-57-27-71-00ZZZ-520Z-A
A350-A-57-27-71-00ZZZ-720Z-A
SYSTEM DESCRIPTION (SD)
A350-A-06-3X-XX-01ZZZ-04CZ-A A350-A-06-4X-XX-01ZZZ-04CZ-A
A350-A-57-2X-XX-01ZZZ-04CZ-A
K. PUBLICATION AFFECTED
None
L. INDUSTRY SUPPORT INFORMATION
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign. For detailed
support, please refer to the related RIL V57M24000307.
For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department: monitored.retrofit@airbus.com.

### Page 11

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 11
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
Material for task set A350-A-57-XX-P091-01000-93BA-A Detailed Inspection of the
Edge Glow Sealant on the Corner Fittings at RIB 1
MATERIAL QTY SEE NOTES
Referenced tools See SB
Consumables See SB
Referenced consumables See SB
B. TOOLING
Referenced tools for task set A350-A-57-XX-P091-01000-93BA-A Detailed
Inspection of the Edge Glow Sealant on the Corner Fittings at RIB 1
T o accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. MP A350-A-57-27-71-00ZZZ-520Z-A
Ref. MP A350-A-57-27-71-00ZZZ-720Z-A
C. CONSUMABLES
Consumables for task set A350-A-57-XX-P091-01000-93BA-A Detailed Inspection
of the Edge Glow Sealant on the Corner Fittings at RIB 1
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
06ABA1 Polysulfide Sealant - FuelT ank Brushable
06ACC1
Polysulfide Sealant - Low
Density MultiPurpose
Interfay
08BBF1 Non Aqueous Cleaner -Methyl-Ethyl-Ketone
14SBA1 T extile - Lint free Cotton
Referenced consumables for task set A350-A-57-XX-P091-01000-93BA-A Detailed
Inspection of the Edge Glow Sealant on the Corner Fittings at RIB 1
T o accomplish this Service Bulletin it is necessary to use the consumable materials listed in:
Ref. MP A350-A-57-27-71-00ZZZ-720Z-A
D. LIST OF NEW PARTS
No parts
E. LIST OF EXISTING PARTS
No parts

### Page 12

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 12
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A350-A-57-XX-P091-01000-93BA-A (A350-A-57-XX-P091-01ZZZ-93BZ-A)
Detailed Inspection of the Edge Glow Sealant on the Corner Fittings at RIB 1
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
WARNING: IF YOU DO ABRASIVE OR POLISHING WORK IN OR NEAR A FUEL TANK, BE
CAREFUL NOT TO MAKE SPARKS. SPARKS CAN CAUSE A FIRE.
WARNING: THIS PROCEDURE USES A FUEL SYSTEM ITEM THAT IS IN A CATEGORY
KNOWN AS A CRITICAL DESIGN CONFIGURATION CONTROL LIMITATION
(CDCCL). CDCCL IDENTIFIES AN ITEM THAT CAN BE THE SOURCE OF A
POSSIBLE FUEL TANK IGNITION. YOU MUST KEEP ALL CDCCL ITEMS IN THE
APPROVED CONFIGURATION. DAMAGE, WEAR OR CHANGES TO A CDCCL
ITEM CAN CAUSE A POSSIBLE TANK EXPLOSION.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO A MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESP A350-A-20-55-XX-01ZZZ-
042Z-A.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: The purpose of flowcharts is to supplement the information given in the Procedure and
Compliance paragraphs and not to serve as the primary source for tasks or compliance
times given in this Service Bulletin.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.

### Page 13

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 13
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including Required for Compliance paragraph
contained herein, contact AIRBUS for further instructions and approval.
A. TASK SET ASSOCIATED INFORMATION
Maintenance Configuration
Fuel tanks opened
Task Manpower
TOTAL MAN-HOURS 34.00 h
ELAPSED TIME (HOURS) 17.00 h
B. PREPARATION
(1) Task A350-A-57-XX-P091-03001-540A-A (A350-A-57-XX-P091-03ZZZ-540Z-A)
General Job Set-Up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Referenced Information
Manuals/Drawings References/Sheets
INTRO A350-A-00-61-04-11ZZZ-018Z-D
MP A350-A-24-41-XX-00ZZZ-170Z-A
Procedure
NOTE: For the basic Aircraft configuration, refer to Ref. INTRO A350-A-00-61-04-
11ZZZ-018Z-D “Maintenance Procedure - Introduction”.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. MP A350-A-24-
41-XX-00ZZZ-170Z-A.
(2) Task A350-A-57-XX-P091-01001-540A-A (A350-A-57-XX-P091-01ZZZ-540Z-A)
Job Set-Up on the LH Wing
WARNING: MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING
NOTICES ARE IN POSITION BEFORE YOU START A TASK ON OR
NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND RELATED DOORS
- THE CARGO DOORS
- THE ENGINES
- OTHER COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO
PERSONS AND/OR DAMAGE TO EQUIPMENT.
WARNING: ALWAYS MAKE SURE THAT THE FUEL-TANK ACCESS PANELS ARE
INSTALLED BEFORE YOU ENERGIZE THE AIRCRAFT ELECTRICAL
SYSTEM. FUEL FUMES ARE FLAMMABLE, AND ELECTRICAL SPARKS
CAN CAUSE FIRES.

### Page 14

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 14
WARNING: MAKE SURE THAT YOU HAVE THE CORRECT FIRE FIGHTING
EQUIPMENT AVAILABLE.
DO NOT GET AIRCRAFT FUEL:
- IN YOUR MOUTH
- IN YOUR EYES
- ON YOUR CLOTHES
- ON YOUR SKIN FOR A LONG TIME.
AIRCRAFT FUEL IS POISONOUS AND CAN GO THROUGH YOUR
SKIN INTO YOUR BODY. FLUSH FUEL AWAY WITH CLEAN WATER
AND IF NECESSARY, GET MEDICAL HELP .
WARNING: BEFORE YOU DO WORK IN OR NEAR A FUEL TANK, MAKE
SURE THAT YOU OBEY ALL THE SAFETY PROCEDURES. THIS
WILL PREVENT INJURY TO PERSONS AND/OR DAMAGE TO THE
AIRCRAFT.
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 14.00 h
Minimum Number of person 2
Elapsed Time 14.00 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-57-27-71-00ZZZ-520Z-A
Procedure
(a) Put an access platform in position at Zone 541.
(b) Do the job set-up procedure as specified in the removal of the fuel tank access-
covers, Panel 541AB and Panel 541CB, refer to Ref. MP A350-A-57-27-71-00ZZZ-
520Z-A.
(c) Remove the fuel tank access cover, Panel 541AB and Panel 541CB, refer to Ref.
MP A350-A-57-27-71-00ZZZ-520Z-A.
(3) Task A350-A-57-XX-P091-02001-540A-A (A350-A-57-XX-P091-02ZZZ-540Z-A)
Job Set-Up on the RH Wing
WARNING: MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING
NOTICES ARE IN POSITION BEFORE YOU START A TASK ON OR
NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND RELATED DOORS
- THE CARGO DOORS
- THE ENGINES
- OTHER COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO
PERSONS AND/OR DAMAGE TO EQUIPMENT.
WARNING: ALWAYS MAKE SURE THAT THE FUEL-TANK ACCESS PANELS ARE
INSTALLED BEFORE YOU ENERGIZE THE AIRCRAFT ELECTRICAL
SYSTEM. FUEL FUMES ARE FLAMMABLE, AND ELECTRICAL SPARKS
CAN CAUSE FIRES.

### Page 15

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 15
WARNING: MAKE SURE THAT YOU HAVE THE CORRECT FIRE FIGHTING
EQUIPMENT AVAILABLE.
DO NOT GET AIRCRAFT FUEL:
- IN YOUR MOUTH
- IN YOUR EYES
- ON YOUR CLOTHES
- ON YOUR SKIN FOR A LONG TIME.
AIRCRAFT FUEL IS POISONOUS AND CAN GO THROUGH YOUR
SKIN INTO YOUR BODY. FLUSH FUEL AWAY WITH CLEAN WATER
AND IF NECESSARY, GET MEDICAL HELP .
WARNING: BEFORE YOU DO WORK IN OR NEAR A FUEL TANK, MAKE
SURE THAT YOU OBEY ALL THE SAFETY PROCEDURES. THIS
WILL PREVENT INJURY TO PERSONS AND/OR DAMAGE TO THE
AIRCRAFT.
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 14.00 h
Minimum Number of person 2
Elapsed Time 14.00 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-57-27-71-00ZZZ-520Z-A
Procedure
(a) Put an access platform in position at Zone 641.
(b) Do the job set-up procedure as specified in the removal of the fuel tank access-
covers, Panel 641AB and Panel 641CB, refer to Ref. MP A350-A-57-27-71-00ZZZ-
520Z-A.
(c) Remove the fuel tank access cover, Panel 641AB and Panel 641CB, refer to Ref.
MP A350-A-57-27-71-00ZZZ-520Z-A.
C. PROCEDURE
(1) Task A350-A-57-XX-P091-01001-300A-A (A350-A-57-XX-P091-01ZZZ-300Z-A)
Do a Detailed Inspection of the Corner Fittings at RIB 1, LH side
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Panel 541AB, Panel 541CB541
Work location Rib 1
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 2
Elapsed Time 1.00 h
Skills Airframe

### Page 16

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 16
Referenced Information
Manuals/Drawings References/Sheets
SD
A350-A-06-3X-XX-01ZZZ-04CZ-A
A350-A-06-4X-XX-01ZZZ-04CZ-A
A350-A-57-2X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-04CZ-A.
2 For the identification of access panels, refer to Ref. SD A350-A-06-4X-XX-
01ZZZ-04CZ-A.
3 For the identification of the ribs, refer to Ref. SD A350-A-57-2X-XX-01ZZZ-
04CZ-A.
(b) In accordance with the threshold given in the PLANNING INFORMATION
paragraph 1.E.(2):
Do a detailed inspection to examine the edge glow sealant at all corner fitting
areas at RIB 1, refer to Ref. Fig.FA Flow Chart and Ref. Fig.BA Inspection of the
Sealant on the Corner Fittings at RIB 1, LH Side.
(c) Depending on the inspection results:
1 If the sealant is correctly applied on all the corner fitting areas at RIB 1:
a No further action required.
2 If the sealant is not correctly applied on the corner fitting areas at RIB 1:
a Apply the sealant in accordance with Ref. T ask A350-A-57-XX-P091-
01ZZZ-600Z-A.
b No further action required.

### Page 17

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-079RN-A-003-01 Fig.FA Sol.AA SHEET 1/1
REV 00 May 30/24 A350-57-P091Flow Chart
Page 17
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
NOTE:
FOR THE ACCOMPLISHMENT TIMESCALE, REFER TO PARAGRAPH 1.E.(2).01
DO A DETAILED INSPECTION OF THE
NO YES
NO FURTHER ACTIONAPPLY THE EDGE GLOW SEALANT ON
CORNER FITTING AT RIB 1 01
IS THE EDGE GLOW
SEALANT CORRECTLY
APPLIED ON ALL THE CORNER
FITTING AREA AT RIB 1?
THE CORNER FITTING AT RIB 1 01
ICN-A350-A-57XXP091-A-FAPE3-079RN-A-003-01

### Page 18

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07A71-A-004-01 Fig.BA Sol.AA SHEET 1/4
REV 00 May 30/24 A350-57-P091Inspection of the Sealant on the
Corner Fittings at RIB 1, LH Side Page 18
CONF ALL
E F
FD
B F
C F
Z541
A
A
RIB1 RIB2
RIB1
RIB2
B
RIB1
TOP SKIN
FRONT SPAR
01 SEALANT ON THE CORNER FITTINGS AT RIB 1 TO BE INSPECTED.
NOTE:
SEALANT 01
A
A
ICN-A350-A-57XXP091-A-FAPE3-07A71-A-004-01

### Page 19

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07A72-A-003-01 Fig.BA Sol.AA SHEET 2/4
REV 00 May 30/24 A350-57-P091Inspection of the Sealant on the
Corner Fittings at RIB 1, LH Side Page 19
CONF ALL
REAR SPAR
TOP SKIN
SEALANT 01
D
BOTTOM SKIN
FRONT SPAR
C
SEALANT 01
01 SEALANT ON THE CORNER
NOTE:
A
A
A
A
FITTINGS AT RIB 1 TO BE
INSPECTED.
RIB1
RIB1
ICN-A350-A-57XXP091-A-FAPE3-07A72-A-003-01

### Page 20

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07AFA-A-003-01 Fig.BA Sol.AA SHEET 3/4
REV 00 May 30/24 A350-57-P091Inspection of the Sealant on the
Corner Fittings at RIB 1, LH Side Page 20
CONF ALL
E
RIB1
REAR SPAR
BOTTOM SKIN
SEALANT01
A
A
01 SEALANT ON THE CORNER FITTINGS AT RIB 1 TO BE INSPECTED.
NOTE:
ICN-A350-A-57XXP091-A-FAPE3-07AFA-A-003-01

### Page 21

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07D07-A-003-01 Fig.BA Sol.AA SHEET 4/4
REV 00 May 30/24 A350-57-P091Inspection of the Sealant on the
Corner Fittings at RIB 1, LH Side Page 21
CONF ALL
01 SEALANT ON THE CORNER FITTINGS AT RIB 1 TO BE INSPECTED.
NOTE:
SEALANT
F
TYPICAL VIEW
RIB2
SEALANT
01
02
02 EXISTING SEALANT.
SPAR LONGERON
01
SEALANT
COVER
CORNER FITTING
A A
01
COVER
SPAR
LONGERON
CORNER
FITTING
SEALANT
TYPICAL VIEW
OVERLAPPING
SEALANT
01
ICN-A350-A-57XXP091-A-FAPE3-07D07-A-003-01

### Page 22

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 22
(2) Task A350-A-57-XX-P091-02001-300A-A (A350-A-57-XX-P091-02ZZZ-300Z-A)
Do a Detailed Inspection of the Corner Fittings at RIB 1, RH side
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Panel 641AB, Panel 641CB641
Work location Rib 1
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 2
Elapsed Time 1.00 h
Referenced Information
Manuals/Drawings References/Sheets
SD
A350-A-06-3X-XX-01ZZZ-04CZ-A
A350-A-06-4X-XX-01ZZZ-04CZ-A
A350-A-57-2X-XX-01ZZZ-04CZ-A
Procedure
(a) Standard practices given in this procedure:
1 For identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-04CZ-A.
2 For the identification of access panels, refer to Ref. SD A350-A-06-4X-XX-
01ZZZ-04CZ-A.
3 For the identification of the ribs, refer to Ref. SD A350-A-57-2X-XX-01ZZZ-
04CZ-A.
(b) In accordance with the threshold given in the PLANNING INFORMATION
paragraph 1.E.(2):
Do a detailed inspection to examine the edge glow sealant at all corner fitting
areas at RIB 1, refer to Ref. Fig.FA Flow Chart and Ref. Fig.BC Inspection of the
Sealant on the Corner Fittings at RIB 1, RH Side.
(c) Depending on the inspection results:
1 If sealant is correctly applied on all the corner fitting areas at RIB 1:
a No further action required.
2 If sealant is not correctly applied on the corner fitting areas at RIB 1:
a Apply the sealant in accordance with Ref. T ask A350-A-57-XX-P091-
02ZZZ-600Z-A.
b No further action required.

### Page 23

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-079RN-A-003-01 Fig.FA Sol.AA SHEET 1/1
REV 00 May 30/24 A350-57-P091Flow Chart
Page 23
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
NOTE:
FOR THE ACCOMPLISHMENT TIMESCALE, REFER TO PARAGRAPH 1.E.(2).01
DO A DETAILED INSPECTION OF THE
NO YES
NO FURTHER ACTIONAPPLY THE EDGE GLOW SEALANT ON
CORNER FITTING AT RIB 1 01
IS THE EDGE GLOW
SEALANT CORRECTLY
APPLIED ON ALL THE CORNER
FITTING AREA AT RIB 1?
THE CORNER FITTING AT RIB 1 01
ICN-A350-A-57XXP091-A-FAPE3-079RN-A-003-01

### Page 24

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07D0F-A-002-01 Fig.BC Sol.AA SHEET 1/4
REV 00 May 30/24 A350-57-P091Inspection of the Sealant on the
Corner Fittings at RIB 1, RH Side Page 24
CONF ALL
Z641
A
RIB1
RIB2
A
B
RIB1
TOP SKIN
FRONT SPAR
SEALANT
A
A
01
FE
D F
FB
FC
RIB1RIB2
01 SEALANT ON THE CORNER FITTINGS AT RIB 1 TO BE INSPECTED.
NOTE:
ICN-A350-A-57XXP091-A-FAPE3-07D0F-A-002-01

### Page 25

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07D0G-A-001-01 Fig.BC Sol.AA SHEET 2/4
REV 00 May 30/24 A350-57-P091Inspection of the Sealant on the
Corner Fittings at RIB 1, RH Side Page 25
CONF ALL
BOTTOM SKIN
FRONT SPAR
RIB1
C
SEALANT
A
A
01
01 SEALANT ON THE CORNER FITTINGS AT RIB 1 TO BE INSPECTED.
NOTE:
ICN-A350-A-57XXP091-A-FAPE3-07D0G-A-001-01

### Page 26

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07D0H-A-001-01 Fig.BC Sol.AA SHEET 3/4
REV 00 May 30/24 A350-57-P091Inspection of the Sealant on the
Corner Fittings at RIB 1, RH Side Page 26
CONF ALL
E
RIB1
REAR SPAR
BOTTOM SKIN
SEALANT
A
A
REAR SPAR
TOP SKIN
SEALANT
D
RIB1
A
A
01
01
01 SEALANT ON THE CORNER FITTINGS AT
NOTE:
RIB 1 TO BE INSPECTED. ICN-A350-A-57XXP091-A-FAPE3-07D0H-A-001-01

### Page 27

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07D0I-A-003-01 Fig.BC Sol.AA SHEET 4/4
REV 00 May 30/24 A350-57-P091Inspection of the Sealant on the
Corner Fittings at RIB 1, RH Side Page 27
CONF ALL
01 SEALANT ON THE CORNER FITTINGS AT RIB 1 TO BE INSPECTED.
NOTE:
SEALANT
F
TYPICAL VIEW
RIB2
SEALANT
01
02
02 EXISTING SEALANT.
SPAR LONGERON
01
SEALANT
COVER
CORNER FITTING
A A
01
COVER
SPAR
LONGERON
CORNER
FITTING
SEALANT
TYPICAL VIEW
OVERLAPPING
SEALANT
01
ICN-A350-A-57XXP091-A-FAPE3-07D0I-A-003-01

### Page 28

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 28
(3) Task A350-A-57-XX-P091-01001-600A-A (A350-A-57-XX-P091-01ZZZ-600Z-A)
Depending on the Inspection Result, Apply Sealant on the Corner Fittings at
RIB 1, LH side
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Panel 541AB, Panel 541CB541
Work location Rib 1
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 2
Elapsed Time 0.50 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
06ABA1 Polysulfide Sealant - FuelT ank Brushable
06ACC1
Polysulfide Sealant - Low
Density MultiPurpose
Interfay
08BBF1 Non Aqueous Cleaner -Methyl-Ethyl-Ketone
14SBA1 T extile - Lint free Cotton
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-24-XX-01ZZZ-667Z-AA350-A-51-76-12-00ZZZ-660Z-A
SD
A350-A-06-3X-XX-01ZZZ-04CZ-A
A350-A-06-4X-XX-01ZZZ-04CZ-A
A350-A-57-2X-XX-01ZZZ-04CZ-A
CML CONSUMABLE MATERIAL LIST (CML)
Procedure
(a) Standard practices given in this procedure:
1 For identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-04CZ-A.
2 For the identification of access panels, refer to Ref. SD A350-A-06-4X-XX-
01ZZZ-04CZ-A.
3 For the identification of the ribs, refer to Ref. SD A350-A-57-2X-XX-01ZZZ-
04CZ-A.
4 For the specification of Material application codes given in this Service
Bulletin, refer to Ref. CML.

### Page 29

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 29
5 Repair the sealant in accordance with Ref. ASR A350-A-51-76-12-00ZZZ-
660Z-A.
6 Apply sealant in accordance with Ref. ASR A350-A-51-24-XX-01ZZZ-667Z-A.
(b) Apply sealant in the affected corner fittings, refer to Ref. Fig.BB Application of the
Sealant on the Corner Fittings at RIB 1, LH Side.
1 Clean the work area with:
  Non Aqueous Cleaner -
Methyl-Ethyl-Ketone
08BBF1  
and
  T extile - Lint free Cotton14SBA1  
2 Lightly abrade the area in accordance with Ref. ASR A350-A-51-76-12-
00ZZZ-660Z-A.
3 Apply the edge glow sealant in the affected areas, refer to Ref. Fig.BB
Application of the Sealant on the Corner Fittings at RIB 1, LH Side, with:
  Polysulfide Sealant
- Low Density
MultiPurpose Interfay
06ACC1  
NOTE: Drying time of the edge glow sealant is 8–12 hours.
4 Apply the overlapping sealant as necessary, refer to Ref. Fig.BB Application
of the Sealant on the Corner Fittings at RIB 1, LH Side, with:
  Polysulfide Sealant -
Fuel T ank Brushable
06ABA1

### Page 30

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07BUV-A-004-01 Fig.BB Sol.AA SHEET 1/4
REV 00 May 30/24 A350-57-P091Application of the Sealant on the
Corner Fittings at RIB 1, LH Side Page 30
CONF ALL
Z541
A
RIB1
RIB2
B
RIB1
TOP SKIN
FRONT SPAR
01 APPLY SEALANT MATERIAL No 06ACC1 AT THE CORNER FITTINGS.
NOTE:
SEALANT 01
A
A
E F
FD
B F
C F A
RIB1 RIB2
ICN-A350-A-57XXP091-A-FAPE3-07BUV-A-004-01

### Page 31

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07BUW-A-003-01 Fig.BB Sol.AA SHEET 2/4
REV 00 May 30/24 A350-57-P091Application of the Sealant on the
Corner Fittings at RIB 1, LH Side Page 31
CONF ALL
REAR SPAR
TOP SKIN
SEALANT 01
D
BOTTOM SKIN
FRONT SPAR
RIB1
C
SEALANT 01
01 APPLY SEALANT MATERIAL
NOTE:
A
A
A
A
No 06ACC1 AT THE CORNER
FITTINGS.
RIB1
ICN-A350-A-57XXP091-A-FAPE3-07BUW-A-003-01

### Page 32

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07BUX-A-003-01 Fig.BB Sol.AA SHEET 3/4
REV 00 May 30/24 A350-57-P091Application of the Sealant on the
Corner Fittings at RIB 1, LH Side Page 32
CONF ALL
E
RIB1
REAR SPAR
BOTTOM SKIN
SEALANT01
01 APPLY SEALANT MATERIAL No 06ACC1 AT THE CORNER FITTINGS.
NOTE:
A
A
ICN-A350-A-57XXP091-A-FAPE3-07BUX-A-003-01

### Page 33

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07D05-A-003-01 Fig.BB Sol.AA SHEET 4/4
REV 00 May 30/24 A350-57-P091Application of the Sealant on the
Corner Fittings at RIB 1, LH Side Page 33
CONF ALL
SPAR LONGERON
02
NOTE:
APPLY A SUFFICIENT THICKNESS TO ENSURE EDGE OF COMPONENT
SHALL NOT BE VISIBLE.
SEALANT
F
TYPICAL VIEW
RIB2
SEALANT
03
05
03 EDGE GLOW SEALANT TO BE APPLIED AT WING BOX JUNCTION STAGE UP TO EXISTING SEALANT.
04 APPLY SEALANT MATERIAL No 06ABA1 AS OVERLAPPING SEALANT AS NECESSARY. 
02
SEALANT
COVER
CORNER FITTING
A A
02
COVER
SPAR
LONGERON
CORNER
FITTING
SEALANT
TYPICAL VIEW
OVERLAPPING
SEALANT
04
05 EXISTING SEALANT. ICN-A350-A-57XXP091-A-FAPE3-07D05-A-003-01

### Page 34

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 34
(4) Task A350-A-57-XX-P091-02001-600A-A (A350-A-57-XX-P091-02ZZZ-600Z-A)
Depending on the Inspection Result, Apply Sealant on the Corner Fittings at
RIB 1, RH side
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
Access Panel 641AB, Panel 641CB641
Work location Rib 1
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 2
Elapsed Time 0.50 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
06ABA1 Polysulfide Sealant - FuelT ank Brushable
06ACC1
Polysulfide Sealant - Low
Density MultiPurpose
Interfay
08BBF1 Non Aqueous Cleaner -Methyl-Ethyl-Ketone
14SBA1 T extile - Lint free Cotton
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-24-XX-01ZZZ-667Z-AA350-A-51-76-12-00ZZZ-660Z-A
SD
A350-A-06-3X-XX-01ZZZ-04CZ-A
A350-A-06-4X-XX-01ZZZ-04CZ-A
A350-A-57-2X-XX-01ZZZ-04CZ-A
CML CONSUMABLE MATERIAL LIST (CML)
Procedure
(a) Standard practices given in this procedure:
1 For identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-04CZ-A.
2 For the identification of access panels, refer to Ref. SD A350-A-06-4X-XX-
01ZZZ-04CZ-A.
3 For the identification of the ribs, refer to Ref. SD A350-A-57-2X-XX-01ZZZ-
04CZ-A.
4 For the specification of Material application codes given in this Service
Bulletin, refer to Ref. CML.

### Page 35

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 35
5 Repair the sealant in accordance with Ref. ASR A350-A-51-76-12-00ZZZ-
660Z-A.
6 Apply sealant in accordance with Ref. ASR A350-A-51-24-XX-01ZZZ-667Z-A.
(b) Apply sealant in the affected corner fittings, refer to Ref. Fig.BD Application of
the Sealant on the Corner Fittings at RIB 1, RH Side.
1 Clean the work area with:
  Non Aqueous Cleaner -
Methyl-Ethyl-Ketone
08BBF1  
and
  T extile - Lint free Cotton14SBA1  
2 Lightly abrade the area in accordance with Ref. ASR A350-A-51-76-12-
00ZZZ-660Z-A.
3 Apply the edge glow sealant in the affected areas, refer to Ref. Fig.BD
Application of the Sealant on the Corner Fittings at RIB 1, RH Side, with:
  Polysulfide Sealant
- Low Density
MultiPurpose Interfay
06ACC1  
NOTE: Drying time of the edge glow sealant is 8–12 hours.
4 Apply the overlapping sealant as necessary, refer to Ref. Fig.BD Application
of the Sealant on the Corner Fittings at RIB 1, RH Side, with:
  Polysulfide Sealant -
Fuel T ank Brushable
06ABA1

### Page 36

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07D09-A-003-01 Fig.BD Sol.AA SHEET 1/4
REV 00 May 30/24 A350-57-P091Application of the Sealant on the
Corner Fittings at RIB 1, RH Side Page 36
CONF ALL
01 APPLY SEALANT MATERIAL No 06ACC1 AT THE CORNER FITTINGS.
NOTE:
Z641
A
RIB1
RIB2
A
B
RIB1
TOP SKIN
FRONT SPAR
SEALANT
A
A
01
FE
D F
FB
FC
RIB1RIB2
ICN-A350-A-57XXP091-A-FAPE3-07D09-A-003-01

### Page 37

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07D0A-A-002-01 Fig.BD Sol.AA SHEET 2/4
REV 00 May 30/24 A350-57-P091Application of the Sealant on the
Corner Fittings at RIB 1, RH Side Page 37
CONF ALL
BOTTOM SKIN
FRONT SPAR
RIB1
C
SEALANT
A
A
01
01 APPLY SEALANT MATERIAL No 06ACC1 AT THE CORNER FITTINGS.
NOTE:
ICN-A350-A-57XXP091-A-FAPE3-07D0A-A-002-01

### Page 38

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07D0B-A-002-01 Fig.BD Sol.AA SHEET 3/4
REV 00 May 30/24 A350-57-P091Application of the Sealant on the
Corner Fittings at RIB 1, RH Side Page 38
CONF ALL
E
RIB1
REAR SPAR
BOTTOM SKIN
SEALANT
A
A
REAR SPAR
TOP SKIN
SEALANT
D
RIB1
A
A
01
01 APPLY SEALANT MATERIAL No 06ACC1
NOTE:
AT THE CORNER FITTINGS.
01
ICN-A350-A-57XXP091-A-FAPE3-07D0B-A-002-01

### Page 39

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP091-A-FAPE3-07D0C-A-003-01 Fig.BD Sol.AA SHEET 4/4
REV 00 May 30/24 A350-57-P091Application of the Sealant on the
Corner Fittings at RIB 1, RH Side Page 39
CONF ALL
SPAR LONGERON
02
NOTE:
APPLY A SUFFICIENT THICKNESS TO ENSURE EDGE OF COMPONENT
SHALL NOT BE VISIBLE.
SEALANT
F
TYPICAL VIEW
RIB2
SEALANT
03
05
03 EDGE GLOW SEALANT TO BE APPLIED AT WING BOX JUNCTION STAGE UP TO EXISTING SEALANT.
04 APPLY SEALANT MATERIAL No 06ABA1 AS OVERLAPPING SEALANT AS NECESSARY. 
02
SEALANT
COVER
CORNER FITTING
A A
02
COVER
SPAR
LONGERON
CORNER
FITTING
SEALANT
TYPICAL VIEW
OVERLAPPING
SEALANT
04
05 EXISTING SEALANT. ICN-A350-A-57XXP091-A-FAPE3-07D0C-A-003-01

### Page 40

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 40
D. PREPARATION FOR TEST
(1) Task A350-A-57-XX-P091-01001-720A-A (A350-A-57-XX-P091-01ZZZ-720Z-A)
Preparation for Test
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-57-27-71-00ZZZ-720Z-A
Procedure
(a) Install the fuel tank access cover, Panel 541AB, Panel 541CB, Panel 641AB and
Panel 641CB, refer to Ref. MP A350-A-57-27-71-00ZZZ-720Z-A.
E. TEST
(1) Task A350-A-57-XX-P091-03001-300A-A (A350-A-57-XX-P091-03ZZZ-300Z-A)
Test
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 1.50 h
Minimum Number of person 3
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-57-27-71-00ZZZ-720Z-A
Procedure
(a) Do the test procedure as specified after the installation of the fuel tank access-
covers, Panel 541AB, Panel 541CB, Panel 641AB and Panel 641CB, refer to Ref.
MP A350-A-57-27-71-00ZZZ-720Z-A.
F. CLOSE-UP
(1) Task A350-A-57-XX-P091-01001-740A-A (A350-A-57-XX-P091-01ZZZ-740Z-A)
Close-up on the LH Wing
WARNING: MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING
NOTICES ARE IN POSITION BEFORE YOU START A TASK ON OR
NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND RELATED DOORS
- THE CARGO DOORS
- THE ENGINES
- OTHER COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO
PERSONS AND/OR DAMAGE TO EQUIPMENT.

### Page 41

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 41
WARNING: ALWAYS MAKE SURE THAT THE FUEL-TANK ACCESS PANELS ARE
INSTALLED BEFORE YOU ENERGIZE THE AIRCRAFT ELECTRICAL
SYSTEM. FUEL FUMES ARE FLAMMABLE, AND ELECTRICAL SPARKS
CAN CAUSE FIRES.
WARNING: MAKE SURE THAT YOU HAVE THE CORRECT FIRE FIGHTING
EQUIPMENT AVAILABLE.
DO NOT GET AIRCRAFT FUEL:
- IN YOUR MOUTH
- IN YOUR EYES
- ON YOUR CLOTHES
- ON YOUR SKIN FOR A LONG TIME.
AIRCRAFT FUEL IS POISONOUS AND CAN GO THROUGH YOUR
SKIN INTO YOUR BODY. FLUSH FUEL AWAY WITH CLEAN WATER
AND IF NECESSARY, GET MEDICAL HELP .
WARNING: BEFORE YOU DO WORK IN OR NEAR A FUEL TANK, MAKE
SURE THAT YOU OBEY ALL THE SAFETY PROCEDURES. THIS
WILL PREVENT INJURY TO PERSONS AND/OR DAMAGE TO THE
AIRCRAFT.
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-57-27-71-00ZZZ-720Z-A
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Do the close-up procedure as specified in the installation of the fuel tank access-
covers, Panel 541AB and Panel 541CB, refer to Ref. MP A350-A-57-27-71-00ZZZ-
720Z-A.
(c) Remove the access platform at Zone 541.
(d) Put the aircraft back to its initial configuration.
(2) Task A350-A-57-XX-P091-02001-740A-A (A350-A-57-XX-P091-02ZZZ-740Z-A)
Close-up on the RH Wing

### Page 42

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 42
WARNING: MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING
NOTICES ARE IN POSITION BEFORE YOU START A TASK ON OR
NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND RELATED DOORS
- THE CARGO DOORS
- THE ENGINES
- OTHER COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO
PERSONS AND/OR DAMAGE TO EQUIPMENT.
WARNING: ALWAYS MAKE SURE THAT THE FUEL-TANK ACCESS PANELS ARE
INSTALLED BEFORE YOU ENERGIZE THE AIRCRAFT ELECTRICAL
SYSTEM. FUEL FUMES ARE FLAMMABLE, AND ELECTRICAL SPARKS
CAN CAUSE FIRES.
WARNING: MAKE SURE THAT YOU HAVE THE CORRECT FIRE FIGHTING
EQUIPMENT AVAILABLE.
DO NOT GET AIRCRAFT FUEL:
- IN YOUR MOUTH
- IN YOUR EYES
- ON YOUR CLOTHES
- ON YOUR SKIN FOR A LONG TIME.
AIRCRAFT FUEL IS POISONOUS AND CAN GO THROUGH YOUR
SKIN INTO YOUR BODY. FLUSH FUEL AWAY WITH CLEAN WATER
AND IF NECESSARY, GET MEDICAL HELP .
WARNING: BEFORE YOU DO WORK IN OR NEAR A FUEL TANK, MAKE
SURE THAT YOU OBEY ALL THE SAFETY PROCEDURES. THIS
WILL PREVENT INJURY TO PERSONS AND/OR DAMAGE TO THE
AIRCRAFT.
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-57-27-71-00ZZZ-720Z-A
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Do the close-up procedure as specified in the installation of the fuel tank access-
covers, Panel 641AB and Panel 641CB, refer to Ref. MP A350-A-57-27-71-00ZZZ-
720Z-A.
(c) Remove the access platform at Zone 641.

### Page 43

A350
SERVICE BULLETIN
REV 00 May 30/24 A350-57-P091
Page 43
(d) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A350-A-57-XX-P091-01001-90AA-A (A350-A-57-XX-P091-01ZZZ-90AZ-A)
Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 44

A350
SERVICE BULLETIN
APPENDIX
REV 00 May 30/24 A350-57-P091
Page 44
APPENDIX
A. MANPOWER GANTT CHART
Manpower Gantt Chart
For an explanation of the man-hours and elapsed time, refer to the next page.

### Page 45

A350
SERVICE BULLETIN
APPENDIX
Figure ICN-A350-A-57XXP091-A-FAPE3-07A6D-A-005-01 Fig.AA Sol.AA SHEET 1/1
REV 00 May 30/24 A350-57-P091Manpower Gantt Chart
Page 45
CONF ALL
MH
ET/S:
PER
MANHOURS
ELAPSED TIME PER STEP
NUMBER OF PERSONS:
:
01
NOTE:
THIS CHART IS ONLY A PROPOSAL. OPERATORS MAY DETERMINE THAT
ANOTHER WAY TO DO THE WORK IS MORE SUITABLE FOR THEM.
IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
ARE NOT REFLECTED IN THIS GANTT CHART.
02
MH ET/S
TOTAL MANHOURS
SB ELAPSED TIME
STEPS PER
33.00
16.50
SB ELAPSED TIME
(HOURS)
GENERAL JOB SET-UP 0.25 1
JOB SET-UP ON THE LH WING 14.00 2
14.00 2
1.00 2
1.00 2
0.25 1
1.50 3
0.25
14.00
14.00
1.00
1.00
0.25
0.50
01
02
ELAPSED TIME ASSUMPTIONS SERVICE BULLETIN No A350-57-P091
0
JOB SET-UP ON THE RH WING
DO A DETAILED INSPECTION OF THE CORNER
DO A DETAILED INSPECTION OF THE CORNER
PREPARATION FOR TEST
TEST
0.50 1 0.50CLOSE-UP ON THE LH WING
0.50 1 0.50CLOSE-UP ON THE RH WING
17
FITTINGS AT RIB 1, LH SIDE
FITTINGS AT RIB 1, RH SIDE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
ICN-A350-A-57XXP091-A-FAPE3-07A6D-A-005-01

### Page 46

A350
SERVICE BULLETIN
APPENDIX
REV 00 May 30/24 A350-57-P091
Page 46
B. REPORTING SHEET
TITLE: WINGS - CENTER WING - RIB1 CORNER FITTING MISSING EDGE GLOW
SEALANT
MODIFICATION No.: None
(1) SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance
and Flight Operations Products if it is duly reported to Airbus.
(2) GENERAL information
The SB Reporting policy is published in ISI 00.00.00135. This document provides
information regarding: the SB Reporting means and benefits, the update of
customized Maintenance Products and customized Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations
Products" for further information on the update of affected Flight Operations Products.
(3) SB Reporting procedure
Standard practice to report SB is to use the online reporting application on
AirbusWorld.
Refer to ISI 00.00.00179:
- For complete information on reporting means to Airbus, Question 2 "What are
the standard practices for SB Reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs,
Question 3 "What about the reporting of prerequisite Service Bulletins?"
NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.

### Page 47

A350
SERVICE BULLETIN
APPENDIX
REV 00 May 30/24 A350-57-P091
Page 47
C. QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin.
The reported data that you provide us will be used to analyse areas of difficulties and to
take corrective action to further improve the quality of our Service Bulletin.
We thank you for the time you have taken in completing this form.
Quality rating of this SB 4 3 2 1
Quality rating of the Accomplishment Instructions 4 3 2 1
Quality rating of the Illustrations 4 3 2 1
Is this SB easy to understand ? Y / N
NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score
If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.
Planning Material Instructions
X Applicability X T ooling X Preparation
X Reason X List of Materials
Operator Supplied
X Mod/Inspection
X Manpower X Kit content X T est
X References X Re-identification X Close-up
X Publication X Illustrations
X Industry Support
Comments :
Operator : Date :
Name/Title
Please return this form to :
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
Or via your Resident Customer Support Office.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
