# Airbus All Operators Transmission A27L014-20

Copy: Revision 1 ("AOT A27L014-20 R01 with Appendix 1"), 9 pages: PDF https://openairdocs.org/files/sha256/9c/c9/9cc942aa841654b8fcf7640532b16d7511345c6394c65760df682047178b9fd2; text https://openairdocs.org/service-documents/airbus/aot-a27l014-20/file/9cc942aa8416.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2021-0371, the docket of AD 2021-15-07. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Other document (All Operators Transmission)
- Number: A27L014-20
- Latest revision known: A27L014-20, Revision 1, dated November 24, 2020 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus/aot-a27l014-20

## Text (9 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2021-0371, the docket of AD 2021-15-07. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

CUSTOMER SERVICES DIRECTORATE
2 ROND POINT EMILE DEWOITINE
31700 BLAGNAC FRANCE
TELEPHONE + 33 (0)5 61 93 33 33
ALERT OPERATORS TRANSMISSION - AOT
AOT ref: A27L014-20 Rev 01 Page 1 of 7 Date: 24-NOV-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
SUBJECT: ATA 27 – THSA lower attachment incorrect installation
AIRCRAFT TYPE: A330,A340
OUR REF.: A27L014-20 Rev 01 dated 24-NOV-2020
OUR PREVIOUS REF: A27L014-20 Rev 00 dated 26-MAY-2020
EFFECTIVE DATE: 04-DEC-2020
0. REASON FOR REVISION
This AOT was issued in May 2020 (Rev 00) to perform a one-time inspection of the THSA lower 
attachment part on A/C for which Ref. 2 or Ref. 3 AMM tasks revision of July 2019 (or later) had not 
been performed. These AMM tasks were revised in July 2019 to allow for the detection of incorrect 
installation. However, further to operators feedback, they are still unclear and contain a few errors.
Therefore, this AOT is revised (Rev 01) in order to:
-Update the list of affected A/C to include all A330 and all A340-200/-300 except:
oA/C already inspected in accordance with Rev 00 of this AOT which provided correct 
information to perform the subject inspection,
oA/C already inspected by Airbus before Entry Into Service,
-Bring the identified errors in Ref. 2 & Ref. 3 AMM tasks to the attention of operators,
- Introduce minor changes to improve clarity, including in Appendixes 1, 2 and 3.
The revised paragraphs are indicated between ***BEG REV*** and ***END REV***.
The modifications are written in blue in Appendixes 1, 2 and 3. 
1. AIRCRAFT AFFECTED
***BEG REV***
All A330 aircraft up to MSN 01965 inclusive, except:
MSN 01795, 01813, 01824, 01844, 01861, 01863, 01865, 01874, 01888, 01902, 01907, 01924, 
01930, 01934, 01952, 01953, 01956, 01957, 01958, 01959, 01960, 01961, 01962, 01963 and 
01964 already inspected by Airbus before Entry Into Service,
MSNs which have already been inspected in accordance with Rev 00 of this AOT.
All A340-200/-300 aircraft, except MSNs which have already been inspected in accordance with Rev 00 
of this AOT.
***END REV***
2. REFERENCED DOCUMENTATION
2.1 APPENDIX
***BEG REV***
Appendix1-Rev01-Context and photo examples
Appendix2-Rev01-Flowchart
Appendix3-Rev01-Reporting Sheet
***END REV***

### Page 2

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27L014-20 Rev 01 Page 2 of 7 Date: 24-NOV-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
2.2 REFERENCES
***BEG REV***
Ref. 1:
For A330 PRE SB 27-3234: Illustrated Parts Catalog (IPC) 27-44-04-01 /-01B /-01C and 
for A340 IPC 27-44-04-03:
- Item 310: BOLT, HEXAGON HEAD, CLOSE TOLERANCE - PN NAS1307-3 – QTY 02
- Item 320: WASHER-TAB - PN BSSP108L – QTY 02
- Item 330: PIN – PN FE134-000-45 - QTY 02
- Item 340: WASHER - PN FE134-000-19 - QTY 02
-Item 350: BEARING – PN 11ANZ24 – QTY 02
For A330 POST SB 27-3234 IPC 27-44-04-01D:
- Item 260: BOLT, HEXAGON HEAD, CLOSE TOLERANCE - PN NAS1307-3 – QTY 02
- Item 270: WASHER-TAB - PN BSSP108L – QTY 02
- Item 280: PIN – PN FE134-000-45 - QTY 02
- Item 290: WASHER - PN FE134-000-19 - QTY 02
-Item 300: BEARING – PN 11ANZ24 – QTY 02
NOTE: The item number will be mentioned hereafter in this AOT as follows (item XX / YY) with:
-XX the corresponding item number for A330 PRE SB 27-3234 (IPC 27-44-01 /-01B /-01C) and 
for A340 IPC 27-44-04-03,
-YY the corresponding item number for A330 POST SB 27-3234 (IPC 27-44-04-01D).
Ref. 2: Aircraft Maintenance Manual (AMM) task 27-44-00-210-801-A - Detailed Inspection of Following 
Items of Trimmable Horizontal Stabilizer (THS) Actuator: Fail Safe Nut, Upper and Lower Attachments 
(Primary and Seco...
Ref. 3: AMM task 27-44-51-400-801-A (or -C) - Installation of the Trimmable Horizontal Stabilizer Actuator 
(THSA) 
Ref. 4: AMM task 55-16-34-200-801-A - Detailed Inspection of Horizontal Stabilizer, Assembly of Trim 
Actuating Arms, Support Fittings and Upper and Lower Attachment Plates
Ref. 5: AMM task 27-44-51-000-801-A ( or -C) - Removal of the Trimmable Horizontal Stabilizer Actuator 
(THSA) 
Ref. 6: AMM task 27-44-51-000-804-A - Removal of the Bearing for the Primary Gimbal Joint
Ref. 7: AMM task 27-44-51-400-804-A - Installation of the Bearing for the Primary Gimbal Joint
NOTE: Unless specifically mentioned, any revision of Airn@v is acceptable for AMM tasks listed in 
this AOT.
***END REV***

### Page 3

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27L014-20 Rev 01 Page 3 of 7 Date: 24-NOV-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
3. REASON
3.1 FACTS
***BEG REV***
Airbus was recently made aware of cases of incorrect installation of Trimmable Horizontal Stabilizer 
Actuator (THSA) lower attachment parts identified in Ref. 1 IPC chapter:
-Event of cup washer (item 340 / 290) not inserted in pin (item 330 / 280), found in production.
-Event of loose bolt (item 310 / 260) not sufficiently secured by keywasher (item 320 / 270) on 
a THSA fitted from delivery and found during accomplishment of Ref. 2 scheduled maintenance 
task (interval 12000FH).
***END REV***
Picture examples of these findings are shown in Appendix 1.
The root cause of this incorrect installation has been attributed to human error in all cases encountered.
***BEG REV***
The instructions for THSA installation have been improved in production. This update has been applied 
from MSN 01966 and on. Some former aircraft have been inspected before Entry Into Service and are, 
therefore, excluded from the list of affected A/C (refer to §1 Affected aircraft).
Following the discovery of similar findings occurring on A300-600, a first update to the A330/A340 AMM 
tasks was made in order to improve clarity on the THSA installation in the July 2019 revision of Airn@v.
After the issuance of Rev 00 of this AOT, errors in Ref. 2 and Ref. 3 AMM tasks were reported as follows:
-Ref 2. Incorrect Figure 27-44-00-991-01000-00-A,
-Ref 3. Missing steps for the installation of subject parts on A/C.
Therefore, the accomplishment of Ref. 2 or Ref. 3 AMM task revision of July 2019 (or later) is no longer 
used to establish the list of affected A/C. Consequently, even A/C for which Ref. 2 or Ref. 3 AMM task 
revision of July 2019 (or later) have been performed, must be inspected in accordance with this AOT. 
Thus, the first step of the flowchart in Appendix 2 has been removed.
The update of the documentation is ongoing (see §5.2 Impacted documentation). Nevertheless, the 
Rev 01 of this AOT must be privileged during this transition period. Therefore all the affected A/C defined 
in §1 are required to perform the inspection in accordance with this AOT.
The same lower attachment (parts and assembly) is applicable on both A330 & A340-200/-300 fleet 
regardless of THSA Part Number. A340-500/-600 fleet is not affected by this AOT due to a different 
attachment principle.
***END REV***
3.2 CONSEQUENCES
***BEG REV***
The incorrect installation of Ref. 1 parts could lead to bolt (item 310 / 260) separation from the THSA, then 
followed by the separation of the keywasher (item 320 / 270), the cup washer (item 340 / 290) and 
ultimately the spherical bearing (item 350 / 300).
***END REV***
NOTE: As per design, the RH bearing moves freely in the THS-actuator arm. The LH bearing is force 
fitted to the THS-actuator arm. The inspection required in this AOT is valid for both LH and RH sides.

### Page 4

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27L014-20 Rev 01 Page 4 of 7 Date: 24-NOV-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
This situation is identified as a load sharing condition between the primary and secondary load paths of 
the THSA.
In case such scenario happens, it would be detected by the Checkable Shear Pin (CSP) implemented by 
mandatory retrofit on the entire fleet since end of December 2016 as per AD 2014-0219. The CSP 
detection is announced to the crew by simultaneous ECAM warnings F/CTL PRIM 2 PITCH FAULT and 
F/CTL PRIM 3 PITCH FAULT.
3.3 AIM
The aim of this AOT is to perform a one-time inspection of the THSA lower attachment, ensuring correct 
installation of Ref. 1 parts and providing corrective actions in case of findings.
4. SHORT TERM ACTION
NOTE 1: This AOT is expected to be classified mandatory by an Airworthiness Directive (AD). The 
accomplishment instructions marked as Required for Compliance (RC) must be done to comply with the 
AD. “RC” is indicating these paragraphs accordingly. 
NOTE 2: The accomplishment instructions of this AOT include procedures given in other documents or in 
other sections of the AOT. When the words ’refer to’ are used and the operator has a procedure accepted 
by the local authority he belongs to, the accepted alternative procedure can be used. When the words ’in 
accordance with’ are used then the given procedure must be followed.
NOTE 3: The access and close-up instructions, not comprising return to service tests, in this AOT do not 
constitute or affect the technical intent of the AOT. Operators can therefore, as deemed necessary, omit 
or add access and/or close-up steps to add flexibility to their maintenance operations as long as the 
technical intent of the AOT is met within the set parameters.
4.1 PLANNING AND MANPOWER
4.1.1 RC - ACCOMPLISHMENT TIMESCALE
***BEG REV***
Aircraft determined affected by §1 of this AOT must be inspected no later than 1000FH from AOT Rev 
01 effective date.
***END REV***
4.1.2 MANPOWER
***BEG REV***
The estimated time to perform the THSA inspection on aircraft is 1.30 MH, which is split as follows:
0.50 MH to get access to the THSA area,
0.30 MH to perform Ref. 2 AMM task revision of July 2019 (or later) with use of AOT Appendix 1,
0.50 MH for the close up.
The following additional time is to be considered depending on the findings:
0.50 MH in case of findings during THSA lower attachment parts inspection and necessary 
replacement/reinstallation of subject parts using Ref. 6 and 7 AMM tasks,
0.20 MH in case of structural inspection required, referring to Ref. 4 AMM task,
24 MH in case of THSA replacement required, referring to Ref. 3 revision of October 2020 (or 
later) and Ref 5 AMM tasks.
***END REV***

### Page 5

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27L014-20 Rev 01 Page 5 of 7 Date: 24-NOV-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4.2 DESCRIPTION
***BEG REV***
The actions to be performed in the frame of this AOT are described in the flowchart of Appendix 2:
1. Description of the inspection to be performed,
2. Description of the actions in case of findings,
3. Report accomplishment and findings to Airbus.
***END REV***
4.2.1 ACCESS
***BEG REV***
For the inspection, get access to the THSA, refer to ‘’job setup’’ paragraph per Ref. 2 AMM task.
***END REV***
In case of findings, refer to ‘’job setup’’ paragraph per Ref. 3, 4 or 5 AMM task as required.
4.2.2 RC - INSPECTION REQUIREMENTS
***BEG REV***
Verification of the correct installation of both LH and RH sides THSA lower attachment are to be 
performed by means of a one-time detailed visual inspection on aircraft while referring to the Ref. 2 
AMM task revision of July 2019 (or later) and the additional information provided in AOT Appendix 1.
Specific attention must be paid to:
- Pin (item 330 / 280) inserted in one hole of cup washer (item 340 / 290),
- Key of keywasher (item 320 / 270) inserted in the other hole of cup washer,
- Bolt (item 310 / 260) flush with keywasher, itself flush with cup washer and bolt cannot move,
- Both tabs of keywasher folded against 1 or 2 faces of bolt head.
Refer only to AOT Appendix 1 for illustration and not to AMM Figure 27-44-00-991-01000-00-A.
NOTE: The LH and RH bearing assemblies are not identical. The LH assembly has a cotter pin while the 
RH assembly does not (refer to AMM Figure 27-44-51-991-01100-00-C (SHEET 2/2)). 
The parts to be inspected in the frame of this AOT are the same on both sides (the cotter pin is not one 
of them).
***END REV***
4.2.3 RC - FINDINGS
***BEG REV***
In the event of incorrect installation on one or both sides (correct assembly provided in Appendix 1), the 
disassembly of the bolt (item 310 / 260), the keywasher (item 320 / 270) and the cup washer (item 340 
/ 290) on both LH and RH sides will be required for inspection using support of the Ref. 6 AMM task. 
These parts will then be reinstalled or replaced depending of their condition using support of the Ref. 7 
AMM task. 
In any case, the keywasher (item 320 / 270) is considered as a consumable part and will need to be 
replaced.
NOTE 1: The correct insertion of the pin (item 330 / 280) in one hole of the cup washer will be checked 
but the pin does not need to be removed.

### Page 6

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27L014-20 Rev 01 Page 6 of 7 Date: 24-NOV-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
NOTE 2: Ref. 6 and Ref. 7 AMM tasks do not need to be entirely performed as the removal of the 
bearing (item 350 / 300) is not necessary. They are only mentioned as support for the 
removal/installation of the bolt (item 310 / 260), the keywasher (item 320 / 270) and the cup washer 
(item 340 / 290).
NOTE 3: For determining the condition of the removed parts (re-usable or not), industry standard 
practices or airline policy will be used. In case of doubt, the parts need to be replaced.
***END REV***
Examples of observed incorrect installation are provided in Appendix 1.
***BEG REV***
In case parts are found separated from the THSA:
Inspection referring to the Ref. 4 AMM task will be required 
and 
THSA has to be replaced referring to Ref. 3 revision of October 2020 (or later) and Ref. 5 AMM 
tasks.
***END REV***
In case of findings in the accomplishment of Ref. 4 AMM task, contact Airbus.
4.3 SPARES AND TOOLING
***BEG REV***
For THSA lower attachment spare parts, please refer to Ref.1 IPC chapter for PN and quantities.
Only the bolt (item 310 / 260), the keywasher (item 320 / 270) and the cup washer (item 340 / 290) need 
to be provisioned.
The bearing (item 350 / 300) and the pin (item 330 / 280) do not need to be provisioned.
No additional specific tooling to the ones called by Ref 2, 3, 4 or 5 AMM tasks are needed.
NOTE: The THS Fixture-Strut Tool PN 98A27407514005 referenced in Ref 6 AMM task is not required 
as the removal of the bearing is not necessary. 
For spare parts order, please contact Collins (FA3T1) at the following address:
GOODRICH ACTUATION SYSTEMS SAS
7-9 AVENUE DE L'EGUILLETTE
95310 SAINT OUEN L'AUMONE
FRANCE
***END REV***
5. FURTHER INFORMATION
5.1 FOLLOW-UP PLAN
None

### Page 7

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27L014-20 Rev 01 Page 7 of 7 Date: 24-NOV-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5.2 IMPACTED DOCUMENTATION
***BEG REV***
Further to operator feedback following the issuance of the Rev 00 of this AOT, and based on the 
information provided in Appendix 1, the Ref. 2 & Ref. 3 AMM tasks are subject to a new update for 
correction and improvement: 
- An update to the Figure 27-44-00-991-01000-00-A of Ref. 2 is scheduled for Revision of April 
2021.
-The missing steps for the installation of subject parts on A/C in Ref. 3 were added in Revision 
of October 2020.
***END REV***
6. AOT APPROVAL
***BEG REV***
The technical content of this document is approved by EASA and is expected to be classified mandatory 
by an AD.
***END REV***
7. REPORTING
Questions about this AOT are to be addressed to Airbus Customer Services through TechRequest on 
Airbus World, selecting Maintenance & Engineering Domain, Engineering Support Section and ATA 27-
40.
As per latest reporting policy (Ref to OIT 999.0018/16), inspection results (with or without findings) are to 
be addressed to Airbus Customer Services through the generic e-mail address: 
inspection.results@airbus.com.
Best Regards,
Christian FREMONT
VICE PRESIDENT ENGINEERING SUPPORT
CUSTOMER SERVICES
Stéphane GOSSELIN
VICE PRESIDENT A330/A340 PROGRAMME
CUSTOMER SERVICES

### Page 8 (OCR)

AOT A27L014-20 Rev 01 - Appendix 1 - Context and photo examples
FR88
2312
FR80
1CS
SEE 27-41-04
SEE 55-16-07
100
110
120
90 80 70
145
155
165
130
310
140
150
20
360
60
350
330
40
160  50  30  340
320
IPC Figure 27-44-04-03 (for A340) shown as example
(Refer to AOT §2.2 according to A/C configuration)
Page 1 of 2

### Page 9 (OCR)

AOT A27L014-20 Rev 01 - Appendix 1 - Context and photo examples
RH view
bolt (item 310 / 260)
cup washer (item 340 / 290)
LH view
3mm
6L-000-7EV3  LH view
LH view
Correct Assembly
1. Pin inserted in one hole of cup washer
2. Key of keywasher inserted in the other hole of
cup washer
3. Bolt flush with keywasher, itself flush with cup washer
and bolt cannot move
4. Both tabs of keywasher folded against 1 or 2 faces of
bolt head
Incorrect Assembly
oin (item 330 / 280)
A. Pin not inserted in dedicated hole, preventing
flush installation of cup washer
keywasher with foldable  B. Key and pin inserted in same hole (no picture example)
tabs (item 320 / 270)  C. Tabs of keywasher insufficiently folded, not
preventing bolt head rotation
D. Loose or improperly torqued bolt
Page 2 of 2

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
