# Airbus Alert Operators Transmission A27P016-20

Copy: Revision 02 ("A27P016-20 Rev 02"), 18 pages: PDF https://openairdocs.org/files/sha256/c3/ad/c3adbe127cb46c61f3610d3e722537559b4e16c4baa013c7adf6a9cfb6fa4d2b; text https://openairdocs.org/service-documents/airbus/aot-a27p016-20/file/c3adbe127cb4.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2021-0833, the docket of AD 2022-25-02. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Other document (Alert Operators Transmission)
- Number: A27P016-20
- Latest revision known: A27P016-20, Revision 02, dated July 19, 2021 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus/aot-a27p016-20

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus/aot-a27p016-20/proposed.md).

## Text (18 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2021-0833, the docket of AD 2022-25-02. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

CUSTOMER SERVICES DIRECTORATE
2 ROND POINT EMILE DEWOITINE
31700 BLAGNAC FRANCE
TELEPHONE + 33 (0)5 61 93 33 33
ALERT OPERATORS TRANSMISSION - AOT
AOT ref: A27P016-20 Rev 02 Page 1 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
SUBJECT: ATA 27 – Check of Slat Power Control Unit (PCU) Torque Sensor Unit (TSU) correct operation
AIRCRAFT TYPE: A350
OUR REF.: A27P016-20 Rev 02 dated 19-JUL-2021
OUR PREVIOUS REF.: A27P016-20 Rev 01 dated 17-DEC-2020
OUR PREVIOUS REF.: A27P016-20 Rev 00 dated 25-NOV-2020
EFFECTIVE DATE: 29-JULY-2021
0. REASON FOR REVISION
This AOT is revised in order to:
oUse Slat PCU Flight Cycles (FC) instead of Aircraft FC for accomplishment timescale calculation. 
oHarmonize wording between this AOT, EASA Airworthiness Directive (AD) Ref. 2021-0053R1 & 
supplier Liebherr Slat PCU EASA Form 1 certificate. 
oAdapt Appendix 4: TSU Health check Flowchart with this AOT wording.
The revised paragraphs are indicated between **BEG REV** and **END REV**.
1. AIRCRAFT AFFECTED
This AOT is applicable to all A350 in-service aircraft which are fitted with Slat PCU P/N 4785A0000-04 or 
4785A0000-05.
2. REFERENCED DOCUMENTATION
2.1 APPENDIX
**BEG REV**
Appendix. 1: Slat transmission system DVI outcome
Appendix. 2: Typical transmission shafts damages
Appendix. 3: TSU Condition Check values recording & Assessment 
Appendix. 4: TSU Health check Flowchart
**END REV**
2.2 REFERENCES
**BEG REV**
Ref. 1: Aircraft Fault Isolation (AFI) TASK A350-A-27-8X-XX-22001-421A-A – “Fault of the Mechanical 
Drive of the Slats (System Jam)”
Ref. 2: Technical Follow-Up (TFU) 27.80.00024 - Slat System Jamming – Geared Rotary Actuator (GRA) 
water ingress
Ref. 3: TFU 27.84.00019 - Slat Power Control Unit Torque Sensing Unit Malfunction
Ref. 4: AOT A27P015-20 Rev 00 dated 20-JUL-20 & Rev 01 dated 03-SEP-20 – Prevention of Slat 
transmission shaft rupture
Ref. 5: EASA AD 2021-0053R1 – ATA 27 – Flight Controls – Slat Transmission Shafts / Slat Power Control 
Unit Torque Sensing Units – Inspection
Ref. 6: Liebherr Slat PCU EASA Form 1 certificate
Ref. 7: Retrofit Information Letter (RIL) V27M20005217 – Check of Slat Power Control Unit (PCU) Torque 
Sensor Unit (TSU) correct operation

### Page 2

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27P016-20 Rev 02 Page 2 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Ref. 8: Liebherr Vendor Service Bulletin (VSB) 4785A-27-06 – Flight Controls - Slat Actuation System - 
Power Control Unit Torque Sensor Unit Health Check Monitoring
**END REV**
3. REASON
3.1 FACTS
A slat system jam event was reported early 2020 during landing phase at slat extension. Post flight 
troubleshooting as per Ref. 1 AFI TASK revealed a double slat transmission shaft disconnection.
Subject sequence of events was due to a combination of:
A slat system jamming attributed to temporary jamming of the Left-Hand (LH) Slat GRA Part 
Number (P/N) 4775A0000-02 at Track 12 (Ref. 2 TFU).
A Malfunction of the Slat system control & monitoring loop due to lack of response from the Slat 
PCU (P/N 4785A0000-04) TSU attributed to excessive wear in the ball guide mechanism (Ref. 3 
TFU).
Supplier Liebherr inspected several returned in-service Slat PCU TSU’s and found similar wear in the ball 
guide mechanism (Ref. 3 TFU). Besides, several operators reported Slat system jamming attributed to 
temporary jamming of Slat GRA (Ref. 2 TFU).
3.2 CONSEQUENCES
A double shaft disconnection / rupture potentially results in one or several surfaces no longer connected 
to either Slat Wing Tip Brake (WTB) or Slat PCU.
3.3 AIM
The aim of this AOT is to provide instructions as follows:
A one-time DVI of Slat transmission system to detect potential pre-damage on Slat transmission.
Repetitive TSU on-wing health checks to monitor the TSU wear evolution.
3.4 INVESTIGATION 
In agreement with airworthiness authorities, Ref. 4 AOT was issued to detect any event of potential former 
undetected system limit-load exceedance & to evaluate severity of TSU wear on higher risk aircraft.
Airbus analysed all data provided during Ref. 4 AOT campaign and defined actions highlighted within this 
AOT chapter 3.4.1 SLAT TRANSMISSION SYSTEM DVI & chapter 3.4.2 SLAT PCU TSU HEALTH 
CHECK.
3.4.1 SLAT TRANSMISSION SYSTEM DVI 
DVI of the Slat transmission system is necessary to ensure that there is no pre-damage on Slat 
transmission system due to any potential former undetected system limit-load exceedance event caused 
by a malfunction of the TSU.
Subject DVI needs to be performed in the pylon area on the defined list of components detailed in chapter 
4.2.1.
3.4.2 SLAT PCU TSU HEALTH CHECK 
Extensive tests and analyses have determined that the TSU may not operate correctly when the wear has 
exceeded a certain limit.

### Page 3

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27P016-20 Rev 02 Page 3 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Consequently, periodic health checks are required to monitor the wear evolution within the Slat PCU 
TSU’s and ensure their correct operation.
4. SHORT TERM ACTION
NOTE: This AOT is classified mandatory or expected to be classified mandatory by an AD. The 
accomplishment instructions marked as Required for Compliance (RC) must be done to comply with the 
AD. “RC” is indicating these paragraphs accordingly. 
NOTE: The accomplishment instructions of this AOT include procedures given in other documents or in 
other sections of the AOT. When the words ’refer to’ are used and the operator has a procedure accepted 
by the local authority he belongs to, the accepted alternative procedure can be used. When the words ’in 
accordance with’ are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this AOT do not 
constitute or affect the technical intent of the AOT. Operators can therefore, as deemed necessary, omit 
or add access and/or close-up steps to add flexibility to their maintenance operations as long as the 
technical intent of the AOT is met within the set parameters.
4.1 PLANNING AND MANPOWER
4.1.1 RC - ACCOMPLISHMENT TIMESCALE 
**BEG REV**
For aircraft fitted with a Slat PCU having accumulated more than or equal to 500 FC since new (NOTE 1) 
or since installation of new TSU’s in supplier Liebherr shop (NOTE 2), at the effective date of the original 
issue of Ref. 5 EASA AD (11-MAR-2021), accomplishment timescale for first inspections in the scope of 
this AOT is 6 months or 350 FC, whichever comes first, from the effective date of the original issue of Ref. 
5 EASA AD (11-MAR-2021).
For aircraft fitted with a Slat PCU having accumulated less than 500 FC since new (NOTE 1) or since 
installation of new TSU’s in supplier Liebherr shop (NOTE 2), at the effective date of the original issue of 
Ref. 5 EASA AD (11-MAR-2021), accomplishment timescale for first inspections in the scope of this AOT 
is 6 months or 350 FC, whichever comes first, from the date when the Slat PCU accumulates 500 FC 
since new (NOTE 1) or since installation of new TSU’s in supplier Liebherr shop (NOTE 2). 
NOTE 1: If the FC accumulated by a Slat PCU are unknown, and if it can be demonstrated that it has not 
been replaced on the aircraft, the FC of this Slat PCU can be considered identical to those accumulated 
by the aircraft since Airbus date of manufacture. 
If a Slat PCU has been replaced, the certificate of release accompanying the replacement Slat PCU will 
determine the time to comply with all AOT actions for the first time. 
NOTE 2: Installation of new TSU’s in supplier Liebherr shop involves reference of approved repair 
procedure "L-4785-ED-0003" in Ref. 6 Slat PCU EASA Form 1 certificate. If reference of "L-4785-ED-
0003" is part of a Ref. 6 Slat PCU EASA Form 1 certificate, subject Slat PCU FC are considered as zero 
for the purpose of compliance to Ref. 5 EASA AD at Ref. 6 Slat PCU EASA Form 1 certificate issue date. 
Refer to table below for summary of accomplishment timescales.
Slat PCU FC
since new or since installation 
of new TSU’s on 11-MAR-2021
Accomplishment timescale
Above 
or equal to 500 FC
6 months or 350FC (whichever comes first) from 11-MAR-2021 (effective date of the 
original issue of Ref. 5 EASA AD)
Below 500 FC 6 months or 350FC (whichever comes first) from the date when the Slat PCU accumulates 500 FC since new or since installation of new TSU’s in supplier Liebherr shop.

### Page 4

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27P016-20 Rev 02 Page 4 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
**END REV**
4.1.2 MANPOWER
The total estimated time to perform the work is between 3 and 13 Man Hours (MH) which is split as follows:
DVI of Slat transmission system per side (LH or Right-Hand (RH)):
2 MH to get access to the pylon area
1 MH to do DVI of slat transmission system in the pylon area
2 MH for close up
Slat PCU TSU health check:
0.5 MH to get access to the Slat PCU
2 MH to perform complete procedure
0.5 MH for close up
4.2 DESCRIPTION
4.2.1 DVI OF SLAT TRANSMISSION SYSTEM
In this chapter, applicability & instructions related to DVI of both LH & RH Slat transmission system is 
provided. 
4.2.1.1 APPLICABILITY 
For all A350 family aircraft highlighted within chapter 1. AIRCRAFT AFFECTED, one-time actions to be 
performed in the frame of chapter 4.2.1. DVI OF SLAT TRANSMISSION SYSTEM are provided here 
below:
**BEG REV**
If DVI was not performed in both LH & RH pylon areas in the frame of Ref. 4 AOT or this AOT, 
proceed as follows:
oTick the box “YES: in LH & RH wings” in AOT “DVI requirement on subject A/C” table 
part of Appendix. 1.
oPerform one-time DVI in both LH & RH pylon areas as per chapters 4.2.1.2 & 4.2.1.3.
If DVI was performed in both LH & RH pylon areas in the frame of Ref. 4 AOT or this AOT, proceed 
as follows:
oTick the box “NO” in AOT “DVI requirement on subject A/C” table part of Appendix. 1.
**END REV**
NOTE: A review of aircraft maintenance logbook is acceptable to determine if DVI was performed in both 
LH & RH wings, provided those records can be relied upon for that purpose. 
4.2.1.2 DVI OF LH SLAT TRANSMISSION SYSTEM
4.2.1.2.1 JOB SET-UP & GET ACCESS
**BEG REV**
Refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat 
Transmission System” Chapter 3 – “Job set-up” to get access to Shaft assy, Bevel Gearbox & 
Steady Bearing Assy as follows:
oShaft Assy S08 Functional Item Number (FIN) 5018CW  
oBevel Gearbox 17° FIN 5019CW 
oShaft Assy S09 FIN 5020CW
oBevel Gearbox 17° FIN 5021CW
oShaft Assy S10 FIN 5022CW

### Page 5

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27P016-20 Rev 02 Page 5 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
oSteady Bearing Assy Small FIN 5023CW
oShaft Assy S11 FIN 5024CW
oSteady Bearing Assy Small FIN 5025CW
oShaft Assy S12 FIN 5026CW
**END REV**
4.2.1.2.2 RC - INSPECTION REQUIREMENTS
Determine whether the P/N of all slat transmission shafts from Shaft S08 FIN 5018CW to Shaft S36 FIN 
5057CW on LH wing can be confirmed using the aircraft maintenance records:
If the P/N of all subject slat transmission shafts on LH wing can be confirmed using the aircraft 
maintenance records, proceed as follows:
oIf all subject slat transmission shafts of the LH wing are P/N 4784AXXXX-02 (XXXX 
stands for any numerical combination) OR if all subject slat transmission shafts of the LH 
wing are P/N 4784AXXXX-03:
Refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of 
the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection 
of all Shaft assy, Bevel Gearbox and Steady Bearing Assy, in the pylon area, as 
follows: 
- Shaft Assy S08 FIN 5018CW  
- Bevel Gearbox 17° FIN 5019CW 
- Shaft Assy S09 FIN 5020CW
- Bevel Gearbox 17° FIN 5021CW
- Shaft Assy S10 FIN 5022CW
- Steady Bearing Assy Small FIN 5023CW
- Shaft Assy S11 FIN 5024CW
- Steady Bearing Assy Small FIN 5025CW
- Shaft Assy S12 FIN 5026CW
oIf all subject slat transmission shafts of the LH wing are a mix of P/N 4784AXXXX-02 and 
P/N 4784AXXXX-03:
Refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of 
the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection 
of all Shaft assy, Bevel Gearbox and Steady Bearing Assy, in the pylon area, as 
follows:
- Shaft Assy S08 FIN 5018CW  
- Bevel Gearbox 17° FIN 5019CW 
- Shaft Assy S09 FIN 5020CW
- Bevel Gearbox 17° FIN 5021CW
- Shaft Assy S10 FIN 5022CW
- Steady Bearing Assy Small FIN 5023CW
- Shaft Assy S11 FIN 5024CW
- Steady Bearing Assy Small FIN 5025CW
- Shaft Assy S12 FIN 5026CW
AND, if all slat transmission shafts P/N 4784AXXXX-02 are located outboard of 
the shaft assy S12 FIN 5026CW, refer to MP TASK A350-A-27-84-XX-00001-
310A-A – “Detailed Inspection of the Slat Transmission System” chapter 4 
“Procedure” to do a detailed inspection of all these slat transmission shafts P/N 
4784AXXXX-02 of the LH wing.

### Page 6

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27P016-20 Rev 02 Page 6 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
If, at least one slat transmission shaft P/N 4784AXXXX-02 is located between 
shaft assy S08 FIN 5018CW and shaft assy S12 FIN 5026CW, no further action 
is required.
If the P/N of all subject slat transmission shafts on LH wing cannot be confirmed using the aircraft 
maintenance records, visually determine the P/N of the following slat transmission shafts in the 
pylon area of LH wing as follows:
- Shaft Assy S08 FIN 5018CW
- Shaft Assy S09 FIN 5020CW
- Shaft Assy S10 FIN 5022CW
- Shaft Assy S11 FIN 5024CW
- Shaft Assy S12 FIN 5026CW
oIf at least one of these slat transmission shafts is P/N 4784AXXXX-02, refer to MP TASK 
A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission 
System” chapter 4 “Procedure” to do a detailed inspection of all Shaft assy, Bevel 
Gearbox and Steady Bearing Assy, in the pylon area, as follows:
- Shaft Assy S08 FIN 5018CW 
- Bevel Gearbox 17° FIN 5019CW 
- Shaft Assy S09 FIN 5020CW
- Bevel Gearbox 17° FIN 5021CW
- Shaft Assy S10 FIN 5022CW
- Steady Bearing Assy Small FIN 5023CW
- Shaft Assy S11 FIN 5024CW
- Steady Bearing Assy Small FIN 5025CW
- Shaft Assy S12 FIN 5026CW
oIf all of these slat transmission shafts are P/N 4784AXXXX-03, refer to MP TASK A350-
A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission System” 
chapter 4 “Procedure” to do a detailed inspection of the whole LH wing slat transmission.
NOTE: For better understanding regarding requirement condition for subject Slat transmission DVI & 
actions to perform on aircraft depending on P/N of slat transmission shafts system from shaft S08 to Shaft 
S36, refer to Flow chart in Appendix. 1.
NOTE: Aircraft are delivered with only one build standard of slat transmission shaft (P/N 4784AXXXX-02 
or P/N 4784AXXXX-03) from Shaft S08 FIN 5018CW to Shaft S36 FIN 5057CW on LH wing. There is no 
mixed configuration at delivery.
Record in Appendix. 1 the results of the inspection.
Refer to chapter 4.2.1.2.3 to define way forward.
4.2.1.2.3 RC – FINDINGS
Referring to Appendix. 2 for typical transmission shafts damage, assess integrity of transmission 
shafts to be inspected through chapter 4.2.1.2.2:
oIn case of no sign of damage, no further action is to be performed except reporting to 
Airbus in Appendix. 1.
oIn case of findings, contact Airbus and provide complete damage assessment report 
(including relevant pictures of the dedicated areas) for further instructions. In this case, 
the complete slat transmission system would have to be completely inspected and 
damaged parts to be replaced.

### Page 7

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27P016-20 Rev 02 Page 7 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
NOTE: It is expected that, in case of findings, the complete slat transmission system would have to be 
completely inspected and affected parts to be replaced.
Report outcome to Airbus in Appendix. 1.
Return the inspected A/C to its original configuration.
4.2.1.3 DVI OF RH SLAT TRANSMISSION SYSTEM
4.2.1.3.1 JOB SET-UP & GET ACCESS
**BEG REV**
Refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat 
Transmission System” Chapter 3 – “Job set-up” to get access to Shaft assy, Bevel Gearbox & 
Steady Bearing Assy as follows:
oShaft Assy S08 Functional Item Number (FIN) 5118CW 
oBevel Gearbox 17° FIN 5119CW
oShaft Assy S09 FIN 5120CW
oBevel Gearbox 17° FIN 5121CW
oShaft Assy S10 FIN 5122CW
oSteady Bearing Assy Small FIN 5123CW
oShaft Assy S11 FIN 5124CW
oSteady Bearing Assy Small FIN 5125CW
oShaft Assy S12 FIN 5126CW
**END REV**
4.2.1.3.2 RC - INSPECTION REQUIREMENTS
Determine whether the P/N of all slat transmission shafts from Shaft S08 FIN 5118CW to Shaft S36 FIN 
5157CW on RH wing can be confirmed using the aircraft maintenance records:
If the P/N of all subject slat transmission shafts on RH wing can be confirmed using the aircraft 
maintenance records, proceed as follows:
oIf all subject slat transmission shafts of the RH wing are P/N 4784AXXXX-02 (XXXX 
stands for any numerical combination) OR if all subject slat transmission shafts of the RH 
wing are P/N 4784AXXXX-03:
Refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of 
the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection 
of all Shaft assy, Bevel Gearbox and Steady Bearing Assy, in the pylon area, as 
follows: 
- Shaft Assy S08 FIN 5118CW  
- Bevel Gearbox 17° FIN 5119CW 
- Shaft Assy S09 FIN 5120CW
- Bevel Gearbox 17° FIN 5121CW
- Shaft Assy S10 FIN 5122CW
- Steady Bearing Assy Small FIN 5123CW
- Shaft Assy S11 FIN 5124CW
- Steady Bearing Assy Small FIN 5125CW
- Shaft Assy S12 FIN 5126CW
oIf all subject slat transmission shafts of the RH wing are a mix of P/N 4784AXXXX-02 and 
P/N 4784AXXXX-03:
Refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of 
the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection

### Page 8

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27P016-20 Rev 02 Page 8 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
of all Shaft assy, Bevel Gearbox and Steady Bearing Assy, in the pylon area, as 
follows:
- Shaft Assy S08 FIN 5118CW  
- Bevel Gearbox 17° FIN 5119CW 
- Shaft Assy S09 FIN 5120CW
- Bevel Gearbox 17° FIN 5121CW
- Shaft Assy S10 FIN 5122CW
- Steady Bearing Assy Small FIN 5123CW
- Shaft Assy S11 FIN 5124CW
- Steady Bearing Assy Small FIN 5125CW
- Shaft Assy S12 FIN 5126CW
AND, if all slat transmission shafts P/N 4784AXXXX-02 are located outboard of 
the shaft assy S12 FIN 5126CW, refer to MP TASK A350-A-27-84-XX-00001-
310A-A – “Detailed Inspection of the Slat Transmission System” chapter 4 
“Procedure” to do a detailed inspection of all these slat transmission shafts P/N 
4784AXXXX-02 of the RH wing.
If, at least one slat transmission shaft P/N 4784AXXXX-02 is located between 
shaft assy S08 FIN 5118CW and shaft assy S12 FIN 5126CW, no further action 
is required.
If the P/N of all subject slat transmission shafts on RH wing cannot be confirmed using the aircraft 
maintenance records, visually determine the P/N of the following slat transmission shafts in the 
pylon area of RH wing as follows:
- Shaft Assy S08 FIN 5118CW
- Shaft Assy S09 FIN 5120CW
- Shaft Assy S10 FIN 5122CW
- Shaft Assy S11 FIN 5124CW
- Shaft Assy S12 FIN 5126CW
oIf at least one of these slat transmission shafts is P/N 4784AXXXX-02, refer to MP TASK 
A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission 
System” chapter 4 “Procedure” to do a detailed inspection of all Shaft assy, Bevel 
Gearbox and Steady Bearing Assy, in the pylon area, as follows:
- Shaft Assy S08 FIN 5118CW  
- Bevel Gearbox 17° FIN 5119CW 
- Shaft Assy S09 FIN 5120CW
- Bevel Gearbox 17° FIN 5121CW
- Shaft Assy S10 FIN 5122CW
- Steady Bearing Assy Small FIN 5123CW
- Shaft Assy S11 FIN 5124CW
- Steady Bearing Assy Small FIN 5125CW
- Shaft Assy S12 FIN 5126CW
oIf all of these slat transmission shafts are P/N 4784AXXXX-03, refer to MP TASK A350-
A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission System” 
chapter 4 “Procedure” to do a detailed inspection of the whole RH wing slat transmission.
NOTE: For better understanding regarding requirement condition for subject Slat transmission DVI & 
actions to perform on aircraft depending on P/N of slat transmission shafts system from shaft S08 to Shaft 
S36, refer to Flow chart in Appendix. 1.

### Page 9

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27P016-20 Rev 02 Page 9 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
NOTE: Aircraft are delivered with only one build standard of slat transmission shaft (P/N 4784AXXXX-02 
or P/N 4784AXXXX-03) from Shaft S08 FIN 5118CW to Shaft S36 FIN 5157CW on RH wing. There is no 
mixed configuration at delivery.
Record in Appendix. 1 the results of the inspection.
Refer to chapter 4.2.1.3.3 to define way forward.
4.2.1.3.3 RC - FINDINGS
Referring to Appendix. 2 for typical transmission shafts damage, assess integrity of transmission 
shafts to be inspected through chapter 4.2.1.3.2:
oIn case of no sign of damage, no further action is to be performed except reporting to 
Airbus in Appendix. 1.
oIn case of findings, contact Airbus and provide complete damage assessment report 
(including relevant pictures of the dedicated areas) for further instructions. In this case, 
the complete slat transmission system would have to be completely inspected and 
damaged parts to be replaced.
NOTE: It is expected that, in case of findings, the complete slat transmission system would have to be 
completely inspected and affected parts to be replaced.
Report outcome to Airbus in Appendix. 1.
Return the inspected A/C to its original configuration.
4.2.2 SLAT PCU TSU HEALTH CHECK
This AOT introduces a repetitive check of the Slat PCU TSU’s correct operation by use of a specific tool.
For tooling definition, availability and ordering: Refer to section 4.3 SPARES AND TOOLING of this AOT 
and Ref. 7 RIL.
4.2.2.1 JOB SET-UP & GET ACCESS
WARNING:
Make sure that the safety devices and the warning notices are in position before you perform a task in the 
vicinity of flight control surfaces. Movement of components can cause severe injury to persons and/or 
damage to equipment.
WARNING:
Before you install/remove the TSU health Monitoring Test set adapter wrench as per Liebherr Ref. 8 VSB, 
strictly comply with manufacturer’s instructions. 
Otherwise, injury to persons and/or damage to equipment can occur.
CAUTION:
Make sure that the maintenance devices of the wing tip brakes are in the 'O' position Ref. MP A350-A-27-
8X-XX-04ZZZ-170Z-A. This prevents the movement of the flap/slat transmission system during 
maintenance.
If the access panel to the WTB is closed, the WTB can only be in the ’O’ position.
CAUTION:
While you use TSU health Monitoring Test set adapter wrench, make sure that there is always sufficient 
clearance between it and the aircraft structure. If you are not careful, damage to equipment and the aircraft 
can occur.

### Page 10

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27P016-20 Rev 02 Page 10 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Make sure that the slats and the droop nose are in the clean configuration (fully retracted) Ref. 
MP A350-A-27-8X-XX-06ZZZ-170Z-A or Ref. MP A350-A-27-5X-XX-05ZZZ-170Z-A.
Make sure that the aircraft electrical circuits are de-energized Ref. MP A350-A-24-41-XX-00ZZZ-
561Z-A.
Make sure that the Yellow hydraulic system is in the depressurized-for-maintenance configuration 
Ref. MP A350-A-29-XX-XX-04ZZZ-562Z-A.
Safety Precautions:
On the center pedestal:
oOn the SLATS/FLAPS control lever, make sure that the SLATS/FLAPS control lever 
(98V27801000000) is installed.
oAdjacent to the SLATS/FLAPS control lever, make sure that the WARNING NOTICE(S) 
is in position to tell persons not to operate the slats/flaps.
Strictly comply with the hydraulic safety procedures when you do work on the hydraulic system 
Ref. MP A350-A-29-XX-XX-00ZZZ-170Z-A.
As necessary, use the applicable SAFETY BARRIER(S) specified in the operator instructions and 
your local regulations.
Get Access:
Make sure that the STEPLADDER 1.0 M (3.3 FT) is in position below access panel 193FB.
Make sure that access panel 193FB is removed Ref. MP A350-A-53-35-75-00ZZZ-520Z-A.
NOTE: At the end of all inspections performed in the frame of chapters 4.2.2.2 RC - LH TSU HEALTH 
CHECK and 4.2.2.3 RC - RH TSU HEALTH CHECK, return the inspected A/C to its original configuration.
4.2.2.2 RC - LH TSU HEALTH CHECK
4.2.2.2.1 INSPECTION REQUIREMENTS
Perform Slat PCU LH TSU health check in accordance with Ref. 8 VSB to measure value “Max 
Dev Inc Trq“ for both LH TSU Linear Variable Displacement Transducers (LVDT) as follows:
oLH SLAT 1
oLH SLAT 2
Record subject values in AOT ”LH TSU Health check data & Decision” table part of Appendix. 3 
for further evaluation.
Refer to chapter 4.2.2.2.2 to assess the data and define way forward.
4.2.2.2.2 FINDINGS
**BEG REV**
Using both “Max Dev Inc Trq” values from LH TSU LVDT “LH SLAT 1” & “LH SLAT 2” recorded in 
Appendix. 3, perform LH TSU data assessment (NOTE 1 & NOTE 2) as follows:
If both LH TSU LVDT “Max Dev Inc Trq” values are strictly below 10 Nm, proceed as follows:
oTick the box “Repeat 350FC” in AOT “LH TSU Health check data & Decision” table part 
of Appendix. 3.
oRepeat LH TSU health check as per chapter 4.2.2 within 350 FC.
If both LH TSU LVDT “Max Dev Inc Trq” values are >= 10 and < 25 Nm, proceed as follows: 
oTick the box “Repeat 150FC” in AOT “LH TSU Health check data & Decision” table part 
of Appendix. 3.
oRepeat LH TSU health check as per chapter 4.2.2 within 150 FC.
If both LH TSU LVDT “Max Dev Inc Trq” values are >= 25 and < 30 Nm, proceed as follows:
oReplace Slat PCU within 16 FC (NOTE 3).

### Page 11

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27P016-20 Rev 02 Page 11 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
oTick the box “Replace Slat PCU within 16FC” in AOT “LH TSU Health check data & 
Decision” table part of Appendix. 3.
oOn date of Slat PCU replacement, if newly installed Slat PCU has NOT yet accumulated 
500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter 
4.2.2 within 6 months or 350 FC, whichever comes first, from the date when the 
Slat PCU accumulates 500 FC since new or since installation of new TSU’s in 
supplier Liebherr shop (NOTE 4).
oOn date of Slat PCU replacement, if newly installed Slat PCU has accumulated more 
than 500 FC since new or since installation of new TSU’s in supplier Liebherr shop 
(NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter 
4.2.2 before next flight.
If at least one LH TSU LVDT “Max Dev Inc Trq” value is equal or above 30 Nm, proceed as 
follows:
oReplace Slat PCU before next flight (NOTE 3 & NOTE 5).
oTick the box “Replace Slat PCU before next flight” in AOT “LH TSU Health check data & 
Decision” table part of Appendix. 2.
oTick the box “YES: in LH wing” in AOT “DVI requirement on subject A/C” table part of 
Appendix. 1.
oProceed with chapter 4.2.1.2 – DVI of LH Slat Transmission system within 15 FC or 150 
FH whichever comes first after the date of TSU health check.
oOn date of Slat PCU replacement, if newly installed Slat PCU has NOT yet accumulated 
500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter 
4.2.2 within 6 months or 350 FC, whichever comes first, from the date when the 
Slat PCU accumulates 500 FC since new or since installation of new TSU’s in 
supplier Liebherr shop (NOTE 4).
oOn date of Slat PCU replacement, if newly installed Slat PCU has accumulated more 
than 500 FC since new or since installation of new TSU’s in supplier Liebherr shop 
(NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter 
4.2.2 before next flight.
NOTE 1: For better understanding regarding aforementioned data assessment & TSU condition check 
decision criteria, refer to Appendix. 4.
NOTE 2: If both LH TSU LVDT “Max Dev Inc Trq” values are not in the same band, the highest value 
defines the decision criteria.
NOTE 3: As the Slat PCU is fitted with 2 TSU’s (LH & RH), replacement of the whole unit as a 
consequence of a single TSU health check bad result (“Max Dev Inc Trq” >= 25 Nm) induce replacement 
of the other subcomponent TSU whatever its condition. 
NOTE 4: Installation of new TSU’s in supplier Liebherr shop involves reference of approved repair 
procedure "L-4785-ED-0003" in Ref. 6 Slat PCU EASA Form 1 certificate. If reference of "L-4785-ED-
0003" is part of a Ref. 6 Slat PCU EASA Form 1 certificate, subject Slat PCU FC are considered as zero 
for the purpose of compliance to Ref. 5 EASA AD at Ref. 6 Slat PCU EASA Form 1 certificate issue date. 
NOTE 5: Even if one of LH & RH TSU health check outcome is “Replace Slat PCU before next flight”, the 
health check of the other TSU is necessary to determine whether DVI of slat transmission system on the 
other wing is necessary.
**END REV**
4.2.2.3 RC - RH TSU HEALTH CHECK

### Page 12

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27P016-20 Rev 02 Page 12 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4.2.2.3.1 INSPECTION REQUIREMENTS
Perform Slat PCU RH TSU health check in accordance with Ref. 8 VSB to measure value “Max 
Dev Inc Trq“ for both RH TSU Linear Variable Displacement Transducers (LVDT) as follows:
oRH SLAT 1
oRH SLAT 2
Record subject values in AOT ”RH TSU Health check data & Decision” table part of Appendix. 3 
for further evaluation.
Refer to chapter 4.2.2.3.2 to assess the data and define way forward.
4.2.2.3.2 FINDINGS
**BEG REV**
Using both “Max Dev Inc Trq” values from RH TSU LVDT “RH SLAT 1” & “RH SLAT 2” recorded in 
Appendix. 3, perform RH TSU data assessment (NOTE 1 & NOTE 2) as follows:
If both RH TSU LVDT “Max Dev Inc Trq” values are strictly below 10 Nm, proceed as follows:
oTick the box “Repeat 350FC” in AOT “RH TSU Health check data & Decision” table part 
of Appendix. 3.
oRepeat RH TSU health check as per chapter 4.2.2 within 350 FC.
If both RH TSU LVDT “Max Dev Inc Trq” values are >= 10 and < 25 Nm, proceed as follows: 
oTick the box “Repeat 150FC” in AOT “RH TSU Health check data & Decision” table part 
of Appendix. 3.
oRepeat RH TSU health check as per chapter 4.2.2 within 150 FC.
If both RH TSU LVDT “Max Dev Inc Trq” values are >= 25 and < 30 Nm, proceed as follows:
oReplace Slat PCU within 16 FC (NOTE 3).
oTick the box “Replace Slat PCU within 16FC” in AOT “RH TSU Health check data & 
Decision” table part of Appendix. 3.
oOn date of Slat PCU replacement, if newly installed Slat PCU has NOT yet accumulated 
500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter 
4.2.2 within 6 months or 350 FC, whichever comes first, from the date when the 
Slat PCU accumulates 500 FC since new or since installation of new TSU’s in 
supplier Liebherr shop (NOTE 4).
oOn date of Slat PCU replacement, if newly installed Slat PCU has accumulated more 
than 500 FC since new or since installation of new TSU’s in supplier Liebherr shop 
(NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter 
4.2.2 before next flight.
If at least one RH TSU LVDT “Max Dev Inc. Trq” value is equal or above 30 Nm, proceed as 
follows:
oReplace Slat PCU before next flight (NOTE 3 & NOTE 5).
oTick the box “Replace Slat PCU before next flight” in AOT “RH TSU Health check data & 
Decision” table part of Appendix. 3.
oTick the box “YES: in RH wing” in AOT “DVI requirement on subject A/C” table part of 
Appendix. 1.
oProceed with chapter 4.2.1.3 – DVI of RH Slat Transmission system within 15 FC or 150 
FH whichever comes first after the date of TSU health check.
oOn date of Slat PCU replacement, if newly installed Slat PCU has NOT yet accumulated 
500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter 
4.2.2 within 6 months or 350 FC, whichever comes first, from the date when the

### Page 13

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27P016-20 Rev 02 Page 13 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Slat PCU accumulates 500 FC since new or since installation of new TSU’s in 
supplier Liebherr shop (NOTE 4).
oOn date of Slat PCU replacement, if newly installed Slat PCU has accumulated more 
than 500 FC since new or since installation of new TSU’s in supplier Liebherr shop 
(NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter 
4.2.2 before next flight.
NOTE 1: For better understanding regarding aforementioned data assessment & TSU condition check 
decision criteria, refer to Appendix. 4.
NOTE 2: If both LH TSU LVDT “Max Dev Inc Trq” values are not in the same band, the highest value 
defines the decision criteria.
NOTE 3: As the Slat PCU is fitted with 2 TSU’s (LH & RH), replacement of the whole unit as a 
consequence of a single TSU health check bad result (“Max Dev Inc Trq” >= 25 Nm) induce replacement 
of the other subcomponent TSU whatever its condition.
NOTE 4: Installation of new TSU’s in supplier Liebherr shop involves reference of approved repair 
procedure "L-4785-ED-0003" in Ref. 6 Slat PCU EASA Form 1 certificate. If reference of "L-4785-ED-
0003" is part of a Ref. 6 Slat PCU EASA Form 1 certificate, subject Slat PCU FC are considered as zero 
for the purpose of compliance to Ref. 5 EASA AD at Ref. 6 Slat PCU EASA Form 1 certificate issue date. 
NOTE 5: Even if one of LH & RH TSU health check outcome is “Replace Slat PCU before next flight”, the 
health check of the other TSU is necessary to determine whether DVI of slat transmission system on the 
other wing is necessary.
**END REV**
4.3 SPARES AND TOOLING
Regarding tooling availability and ordering, refer to Ref. 7 RIL.
4.3.1 DVI OF SLAT TRANSMISSION SYSTEM
REFERENCE QTY DESIGNATION
98V27801000000 1 CONTROL LEVER FLAP SLAT
NO SPECIFIC AR SAFETY CLIP - CIRCUIT BREAKER
NO SPECIFIC AR SAFETY BARRIER(S)
NO SPECIFIC AR WARNING NOTICE(S)
NO SPECIFIC 1 ACCESS PLATFORM 3M (10 FT)-ADJUSTABLE
NO SPECIFIC 1 ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE
08BAA9 AR Non Aqueous cleaner_General
14SBA1 AR Textile_Lint free Cotton -
4.3.2 SLAT PCU TSU HEALTH CHECK
REFERENCE QTY DESIGNATION
98V27801000000 1 CONTROL LEVER FLAP SLAT
NO SPECIFIC AR SAFETY BARRIER(S)
NO SPECIFIC AR WARNING NOTICE(S)
53784A0000-01 1 TSU HEALTH MONITORING TEST SET
5. FURTHER INFORMATION

### Page 14

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A27P016-20 Rev 02 Page 14 of 14 Date: 19-JUL-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5.1 FOLLOW-UP PLAN
**BEG REV**
Introduction of Slat PCU P/N 4785A0000-06.
It will be introduced for after-market via a monitored retrofit covered by Service Bulletin (SB) Ref. 27-P055. 
**END REV**
5.2 IMPACTED DOCUMENTATION
Not applicable.
6. AOT APPROVAL
The technical content of this document is approved under the authority of the DOA ref.EASA.21J.031.
7. REPORTING
Questions about this AOT are to be addressed to Airbus Customer Services through TechRequest on 
Airbus World, selecting Maintenance & Engineering Domain, Engineering Support Section and ATA 27-
84.
As per latest reporting policy (Ref to OIT 999.0018/16), inspection results (with or without findings) are to 
be addressed to Airbus Customer Services through the generic e-mail address:  
inspection.results@airbus.com.
Retrofit will be performed through the monitored retrofit described in Ref. 7 RIL.
Best Regards,
Christian FREMONT
VICE PRESIDENT ENGINEERING SUPPORT
CUSTOMER SERVICES
Mathieu DUMAS
HEAD OF A350 FLEET EFFICIENCY
CUSTOMER SERVICES

### Page 15

Appendix 1 : Slat transmission system DVI outcome
Relevant Information
Report Build Standard configuration 
(A, B, C or D)
LH wing:
RH wing:
Observations of 
Detailed Visual inspection (DVI)
Check date 
(DD/MM/YYYY) MSN P/N S/N FH FC
Slat PCU information at the date of the check
Appendix linked to AOT A27P016-20 Rev 02 Chapters 4.2.1.1 & 4.2.1.2 & 4.2.1.3 & 4.2.2.2 & 4.2.2.3
- Results of inspection:
DVI required? (Tick the right box) 
NO YES: in LH wing YES:in RH wing YES:in LH & RH wings
DVI Requirement on subject A/C:
BS: Build Standard
(*) Only if all shafts BS P/N 4784AXXXX-02 are located outboard of the pylon area
- Determination of the P/N of all slat transmission shafts outboard of S08:
Configuration A
Configuration B
Configuration C
Configuration D
OR 
(if not possible)

### Page 16

Appendix 2: Typical transmission shafts damages
Appendix linked to AOT A27P016-20 Rev 02 Chapter 4.2.1.2 & 4.2.1.3
Healthy transmission shaft with straight splines
Failed transmission shaft with spirally deformed splines

### Page 17

Appendix 3: TSU Condition Check values Recording & Assessment
Appendix linked to AOT A27P016-20 Rev 02 Chapters 4.2.2.2 & 4.2.2.3
LVDT Max Dev Inc Trq(Nm) LH TSU health check outcome (Tick the right box)Repeat 350FC Repeat 150FC Replace Slat PCUwithin 16FC Replace Slat PCU before next flight
LH SLAT 1
LH SLAT 2
Check date 
(DD/MM/YYYY)
A/C 
registration MSN
Aircraft information at the date of the check
Slat PCU information at the date of the check
P/N S/N FH FC
LH TSU Health check data & Decision
RH TSU Health check data & Decision
LVDT Max Dev Inc Trq(Nm) RH TSU health check outcome (Tick the right box)Repeat 350FC Repeat 150FC Replace Slat PCUwithin 16FC Replace Slat PCU before next flight
RH SLAT 1
RH SLAT 2

### Page 18 (OCR)

Appendix 4: TSU Condition Check Flowchart
Appendix linked to AOT A27P016-20 Rev 02 Chapter 4.2.2.2 & 4.2.2.3
Yes  NOTE 1:
No further  Action  Is installed SPCU P/N 4785A0000-06 ?  The following Flow chart is described for LH TSU.  The same flow chart is to be considered for RH TSU
NOTE 2 :
No
• : First TSU Health check conditions
• • : Repetitive TSU Health check conditions
On 11-MAR-2021,  › : Terminating Action
Yes  No
Was SPCU life >= 500 FC since new or since
installation of new TSUs in shop (NOTE 3) ?  NOTE 3:
Installation of new TSUs in shop involves reference of repair
procedure "L-4785-ED-0003" in Liebherr SPCU EASA Form 1
Perform Health check of both LH & RH TSUs by 11-SEPT
or before affected part accumulates 350FC since 11-MAR,
whichever comes first
Perform Health check of both LH & RH TSUs within 6 months
or 350 FC, whichever comes first, after the
affected part accumulates 500 FC
No further  Is installed SPCU P/N 4785A0000-06 ?
Action
Once required perform TSU HEALTH CHECK:
Test both TSU LVDTs
LH SLAT 1 & LH SLAT 2
and record the two "Max Dev Inc. Trq" values
NOTE 4:
Test to be performed with TSU Health Monitoring Test Set
P/N 53784A0000-01 in accordance with with VSB 4785A-27-06
Yes
Repeat LH TSU Health
MAX( LH SLAT 1, LH SLAT 2) < 10 Nm?
check within 350FC
No
Yes
Repeat LH TSU Health  MAX( LH SLAT 1, LH SLAT 2) < 25 Nm?
check within 150FC
No
Repeat LH & RH TSU Health check on
MAX( LH SLAT 1, LH SLAT 2) < 30 Nm?  installed SPCU before next flight
No
Replace Slat PCU within 16 Flight Cycles  & Perform DVI in LH wing pylon area  Replace Slat PCU before next flight  Yes  No
On Date of replacement,
Is SPCU life >= 500 FC since new or since
installation of new TSUs in shop (NOTE 3) ?
No further  Yes  No
Is installed SPCU P/N 4785A0000-06 ?.
Action

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
