# Airbus Alert Operators Transmission A29L010-19

Copy: Revision 01 ("AOT A29L010-19 R01"), 9 pages: PDF https://openairdocs.org/files/sha256/1b/e8/1be8b5d24db7f6b146e29f3f5ac87a319fa2349c7aa80408986539246ee09e42; text https://openairdocs.org/service-documents/airbus/aot-a29l010-19/file/1be8b5d24db7.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2020-0674; AD 2021-01-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Other document (Alert Operators Transmission)
- Number: A29L010-19
- Latest revision known: A29L010-19, Revision 01, dated February 18, 2020 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus/aot-a29l010-19

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2021-01-06](https://openairdocs.org/ad/2021-01-06.md), effective Mar 30, 2021: Revision 01

## Text (9 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2020-0674; AD 2021-01-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

CUSTOMER SERVICES DIRECTORATE
2 ROND POINT EMILE DEWOITINE
31700 BLAGNAC FRANCE
TELEPHONE + 33 (0)5 61 93 33 33
ALERT OPERATORS TRANSMISSION - AOT
AOT ref: A29L010-19 Rev 01 Page 1 of 9 Date: 18-FEB-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
SUBJECT: ATA 29 – Ground Service Manifold (GSM) manual-valve screw failure
AIRCRAFT TYPE: A330,A340
OUR REF.: A29L010-19 Rev 01 dated 18-FEB-2020
OUR PREVIOUS REF.: A29L010-19 Rev 00 dated 18-DEC-2019
0. REASON FOR REVISION
This AOT is revised to change the torque values of the screws and to add GSM PN 70902-5 as a potential 
affected part, with the following consequences:
- Changes to the AIRCRAFT AFFECTED paragraph
- Changes to the compliance time
- Introduction of a visual inspection for GSM PN 70902-5
- Introduction of replacement of screws that were torqued to the values specified in AOT A29L010-
19 Rev 00
This revision opportunity has been taken to also change the safety-wire procedure reference.
The revised paragraphs are indicated between ***BEG REV*** and ***END REV***.
1. AIRCRAFT AFFECTED
***BEG REV***
A330 with GSM PN 70902-3 / -4 / -5 installed 
A340-200 / -300 with GSM PN 70902-3 / -4 / -5 installed 
***END REV***
NOTE – GSMs are not installed on aircraft post-MOD 58345 (HYDRAULIC POWER - MAIN HYDRAULIC 
POWER - DELETE GROUND SERVICE MANIFOLDS AND ADAPT OF HYDR SYS).
2. REFERENCED DOCUMENTATION
2.1 REFERENCES
Ref 1: RIL LR29M19009215 Rev 01 to be issued by February 2020 at the latest.
3. REASON
The purpose of this AOT is to:
- Inform operators about a risk of Ground Service Manifold (GSM) valve screw failure with 
subsequent leak, system loss, possible manual valve ejection that could damage surrounding 
components and cause injury to ground personnel working in the area.
- Introduce actions to prevent the failure from occurring.
3.1 FACTS
An A330 performed an In-Flight Turn-Back due to loss of the Green and Blue hydraulic systems. This was 
caused by a manual valve that fully departed from the Green hydraulic system GSM (located in the MLG

### Page 2

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A29L010-19 Rev 01 Page 2 of 9 Date: 18-FEB-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
bay), crossed the MLG bay and damaged a Blue hydraulic system pipe. All four screws attaching the 
manual valve were found ruptured.
3.2 CONSEQUENCES
Ejection of the manual valve could lead to:
-Injury to ground personnel working in the MLG bay,
-Loss of one or two hydraulic systems,
-Potential damage to equipment in the surrounding area.
3.3 AIM
***BEG REV***
The aim of this AOT is as follows:
-For GSMs PN 70902-3 / -4, replace the GSM manual-valve screws PN NAS1101-3H8 by new 
(zero FC) screws PN NAS1101-3H8 and replace them repetitively not exceeding 10,000 FC since 
last replacement.
-For GSM PN 70902-5, perform a one-time visual inspection to determine if GSM manual-valve 
screws PN NAS1101-3H8 are installed instead of correct bolts PN EWB0420D-3H-3. 
***END REV***
The aircraft are equipped with 3 GSMs – one for the Green system, one for the Blue system, and one for 
the Yellow system. Each GSM includes 3 valves held in place by 4 screws / bolts each.
Implementation of the corrective actions will be monitored by Airbus via RIL Ref. 1.
4. ACTION
NOTE 1: This AOT is expected to be classified mandatory by an Airworthiness Directive (AD). The 
accomplishment instructions marked as Required for Compliance (RC) must be done to comply with the 
AD. “RC” is indicating these paragraphs accordingly. 
NOTE 2: The accomplishment instructions of this AOT include procedures given in other documents or in 
other sections of the AOT. When the words ’refer to’ are used and the operator has a procedure accepted 
by the local authority he belongs to, the accepted alternative procedure can be used. When the words ’in 
accordance with’ are used then the given procedure must be followed.
NOTE 3: The access and close-up instructions, not comprising return to service tests, in this AOT do not 
constitute or affect the technical intent of the AOT. Operators can therefore, as deemed necessary, omit 
or add access and/or close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the AOT is met within the set parameters.
***BEG REV***
The action affects GSM PNs 70902-3 / -4 / -5 installed in any of the following positions:
-FIN 5109JM1
-FIN 5109JM2
-FIN 5109JM3

### Page 3

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A29L010-19 Rev 01 Page 3 of 9 Date: 18-FEB-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4.1 For GSM PN 70902-3 / -4:
4.1.1 The GSMs’ NAS1101-3H8 screws which have exceeded 10,000 FC (see Note below) must be 
replaced by new NAS1101-3H8 screws i.e. screws with zero FC accumulated, in accordance with 
paragraph 4.4.
NOTE – If the FC accumulated by the screws are unknown, the FC accumulated by the GSM 
apply. If the FC accumulated by the GSM are unknown, the FC accumulated by the aircraft apply.
In case the NAS1101-3H8 screws were torqued to between 5.08 and 5.64 N•m (between 45 
and 50 in-lb) as per Rev 00 of this AOT, these screws must be replaced by new NAS1101-3H8 
screws i.e. screws with zero FC accumulated, in accordance with paragraph 4.4. 
4.2 For GSM PN 70902-5:
4.2.1 In accordance with paragraph 4.4, visually inspect the GSM to determine the PN of the installed 
screws / bolts. 
If screws PN NAS1101-3H8 are found installed and have exceeded 10,000 FC (see Note 
below), replace these screws either by:
obolts PN EWB0420D-3H-3 in accordance with paragraph 4.4, OR if not available:
onew NAS1101-3H8 screws i.e. screws with zero FC accumulated, in accordance with 
paragraph 4.4. Replace these new screws PN NAS1101-3H8 by bolts PN EWB0420D-
3H-3 at the next opportunity and before the screws PN NAS1101-3H8 exceed 10,000 
FC, in accordance with paragraph 4.4.
NOTE – If the FC accumulated by the screws are unknown, the FC accumulated by the GSM 
apply. If the FC accumulated by the GSM are unknown, the FC accumulated by the aircraft apply.
If bolts PN EWB0420D-3H-3 are found installed, no further action is required.
4.3 PLANNING AND MANPOWER
4.3.1 RC - ACCOMPLISHMENT TIMESCALE
For GSM PN 70902-3 / -4:
Initial screw replacement
Before the manual-valve screws PN NAS1101-3H8 exceed 10,000 FC (see Note below) 
since first installation on an aeroplane, or within 1,300 FH from 03 January 2020, 
whichever occurs later, comply with the “Action” paragraph 4.1.1 on the GSMs of the 
Green and Yellow hydraulic systems.
Before the manual-valve screws PN NAS1101-3H8 exceed 10,000 FC (see Note below) 
since first installation on an aeroplane, or within 2,300 FH from 03 January 2020, 
whichever occurs later, comply with the “Action” paragraph 4.1.1 on the GSM of the Blue 
hydraulic system.
NOTE – If the FC accumulated by the screws are unknown, the FC accumulated by the 
GSM apply. If the FC accumulated by the GSM are unknown, the FC accumulated by 
the aircraft apply.

### Page 4

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A29L010-19 Rev 01 Page 4 of 9 Date: 18-FEB-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Recurring action
At intervals not to exceed 10,000 FC since last screw replacement, the screws must be 
replaced again using paragraph 4.4. 
For GSM PN 70902-3 / -4 with NAS1101-3H8 screws torqued to between 5.08 and 5.64 N•m 
(between 45 and 50 in-lb) as per Rev 00 of this AOT:
Within 1,000 FC from accomplishment of this AOT’s Rev 00, comply with the “Action” 
paragraph 4.1.2 on the GSMs of the Green, Yellow, and Blue hydraulic systems. This is 
equal to initial screw replacement.
For GSM PN 70902-5:
Within 1,300 FH from issuance of this AOT Rev 01, comply with the “Action” paragraph 
4.2.1 on the GSMs of the Green, Yellow, and Blue hydraulic systems.
4.3.2 MANPOWER
The estimated time necessary to accomplish the Action is 3.5 man-hours for all three GSMs, if performed 
on-wing. The estimated preparation time is 3 man-hours for all three GSMs.
4.3.3 MATERIAL INFORMATION
GSM PN 70902-3 / -4:
New Part Number Qty per 
aircraft
Part Name Old Part Number Instructions/Disposition
NAS1101-3H8 36 Screw NAS1101-3H8 Discard old part
GSM PN 70902-5:
New Part Number Qty per 
aircraft
Part Name Old Part Number Instructions/Disposition
EWB0420D-3H-3 36 Bolt
MS14183P-C3 36 Washer NAS1101-3H8 Discard old part
***END REV***
4.4 DESCRIPTION
4.4.1 ACCESS 
WARNING: 
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL 
MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
WARNING: 
BEFORE YOU DO WORK ON THE HYDRAULIC SYSTEM, MAKE SURE THAT YOU OBEY THE 
HYDRAULIC SAFETY PROCEDURES. THIS WILL PREVENT INJURY TO PERSONS AND/OR 
DAMAGE TO THE AIRCRAFT.

### Page 5

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A29L010-19 Rev 01 Page 5 of 9 Date: 18-FEB-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
WARNING: 
USE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU 
CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR 
MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
CAUTION: 
DO NOT OPERATE THE FLAPS AND SLATS WHEN ONE OR MORE "LEAK MEASUREMENT 
VALVES" PUSHBUTTON SWITCHES ARE IN THE RELEASED POSITION ("OFF" LEGEND ON). 
OPERATION OF THE FLAPS AND SLATS IN THIS CONFIGURATION CAN CAUSE JAMMING OF THE 
MECHANICAL TRANSMISSION.
Green Ground Service Manifold => Perform:
AMM SUBTASK 29-19-41-860-050-A Aircraft Maintenance Configuration
AMM SUBTASK 29-19-41-010-050-A Get Access
AMM SUBTASK 29-19-41-865-050-A Open, safety and tag this (these) circuit breaker(s):
AMM SUBTASK 29-19-41-941-050-A Safety Precautions
Blue Ground Service Manifold => Perform:
AMM SUBTASK 29-19-41-860-052-A Aircraft Maintenance Configuration
AMM SUBTASK 29-19-41-010-051-A Get Access
AMM SUBTASK 29-19-41-865-053-A Open, safety and tag this (these) circuit breaker(s):
AMM SUBTASK 29-19-41-941-051-A Safety Precautions
Yellow Ground Service Manifold => Perform:
AMM SUBTASK 29-19-41-860-054-A Aircraft Maintenance Configuration
AMM SUBTASK 29-19-41-010-052-A Get Access
AMM SUBTASK 29-19-41-865-056-A Open, safety and tag this (these) circuit breaker(s):
AMM SUBTASK 29-19-41-941-052-A Safety Precautions
4.4.2 ACCOMPLISHMENT INSTRUCTIONS
NOTE – Item Numbers refer to Figure 1 herein.
The below instructions are applicable on-wing.
4.4.2.1 ACCOMPLISHMENT INSTRUCTIONS FOR GSM PN 70902-3 / -4
CAUTION – New NAS1101-3H8 screws shall be used.
(1) Refer to the Aircraft Maintenance Manual 29-19-41 to gain access to the ground service manifold 
and preparation for update. Ensure that all hydraulic systems and hydraulic reservoirs are 
depressurized.
(2) Cut and remove safety wire from screws [1].
(3) Starting in one corner of the manual valve assembly, remove and discard one screw [1].
(4) Apply MCS 352 B lubricant on the threads and under each new screw head [1].
***BEG REV***
(5) Install one new screw [1]. Torque screw to between 1.7 and 2.3 N•m (between 15 and 20 in-lb).
***END REV***

### Page 6

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A29L010-19 Rev 01 Page 6 of 9 Date: 18-FEB-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
(6) Repeat steps (3), (4) and (5) above for the remaining 3 screws, remembering to do one screw at 
a time.
(7) Repeat steps (3) through (6) above for the remaining two manual valve assemblies.
(8) Refer to the Aircraft Maintenance Manual 29-19-41 and test the ground service manifold in 
accordance with the respective task.
***BEG REV***
(9) After successful completion of testing, re-torque screws [1] to between 1.7 and 2.3 N•m (between 
15 and 20 in-lb).
(10)Safety wire screws [1] using MS20995C32 safety wire in accordance with AMM TASK 20-11-11-
911-803-A, double wirelocking.
***END REV***
Figure 1
***BEG REV***
4.4.2.2 ACCOMPLISHMENT INSTRUCTIONS FOR GSM PN 70902-5
CAUTION – New EWB0420D-3H-3 bolts and MS14183P-C3 washers shall be used.
(1) Refer to the Aircraft Maintenance Manual 29-19-41 to gain access to the ground service manifold 
and preparation for update. Ensure that all hydraulic systems and hydraulic reservoirs are 
depressurized.
(2) Visually inspect the GSM to determine the PN of the installed manual-valve screws / bolts. 
Determination is to be done using Figures 2 and 3 below. Screws PN NAS1101-3H8 also have a

### Page 7

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A29L010-19 Rev 01 Page 7 of 9 Date: 18-FEB-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
marking “NAS1101” on their heads (not illustrated in Figure 2), which may be used as an 
additional means of determination, if possible. 
 
Figure 2 – Screws PN NAS1101-3H8
 
  
Figure 3 – Bolts PN EWB0420D-3H-3
If screws PN NAS1101-3H8 are found installed, proceed with steps (3) to (11). 
NOTE – If bolts PN EWB0420D-3H-3 are not available for accomplishment of steps (3) to (11), a 
one-time replacement of screws PN NAS1101-3H8 by new screws PN NAS1101-3H8 is 
permitted as indicated in paragraph 4.2. In this case, follow Accomplishment Instructions 4.4.2.1. 
If bolts PN EWB0420D-3H-3 are found installed, proceed directly to Paragraph 4.4.3 CLOSE-UP.
(3) Cut and remove safety wire from screws [1].
(4) Starting in one corner of the manual valve assembly, remove and discard one screw [1].
(5) Apply MCS 352 B lubricant on the threads and under each head of new bolt PN EWB0420D-
3H-3 and new washer PN MS14183P-C3.
(6) Install one new washer PN MS14183P-C3 and one new bolt PN EWB0420D-3H-3. Torque bolt 
to between 5.08 and 5.64 N•m (between 45 and 50 in-lbs).
(7) Repeat steps (3), (4) and (5) above for the remaining 3 screws / bolts, remembering to do one 
screw / bolt at a time.

### Page 8

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A29L010-19 Rev 01 Page 8 of 9 Date: 18-FEB-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
(8) Repeat steps (3) through (6) above for the remaining two manual valve assemblies.
(9) Refer to the Aircraft Maintenance Manual 29-19-41 and test the ground service manifold in 
accordance with the respective task.
(10)After successful completion of testing, re-torque bolts to between 5.08 and 5.64 N•m (between 
45 and 50 in-lbs).
(11)Safety wire bolts using MS20995C32 safety wire in accordance with AMM TASK 20-11-11-911-
803-A, double wirelocking.
*** END REV***
4.4.3 CLOSE-UP
Green Ground Service Manifold => Perform:
AMM SUBTASK 29-19-41-410-050-A Close Access
AMM SUBTASK 29-19-41-862-050-A De-energize the aircraft electrical circuits
Blue Ground Service Manifold => Perform:
AMM SUBTASK 29-19-41-410-053-A Close Access
AMM SUBTASK 29-19-41-862-051-A De-energize the aircraft electrical circuits
Yellow Ground Service Manifold => Perform:
AMM SUBTASK 29-19-41-410-052-A Close Access
AMM SUBTASK 29-19-41-862-052-A De-energize the aircraft electrical circuits
4.5 SPARES AND TOOLING
***BEG REV***
For GSM PN 70902-3 / -4:
Ordering of new screws may be done through the Airbus Spares website http://spares.airbus.com, or 
SPEC2000.
For ordering by email: Please order the material via your Single Point of Contact (SPOC) operating within 
the Customer Order Fulfilment (COF) in Hamburg. If you do not know your SPOC and need further 
assistance, please call +49 40 5076 4002.
For GSM PN 70902-5:
Ordering of new bolts may be done by contacting Eaton using the following details:
Eaton Aerospace
Sterer Engineering, 
4690 Colorado Blvd., 
Los Angeles, CA 90039,
USA. 
ATTENTION: Repair and Overhaul Department 
Telephone: +1 818 409 0267 
Fax: +1 818 409 1565

### Page 9

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A29L010-19 Rev 01 Page 9 of 9 Date: 18-FEB-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
***END REV***
No special tooling is required.
5. AOT APPROVAL
The technical content of this document is approved under the authority of DOA nr. EASA.21J.031.
6. REPORTING
Questions about this AOT are to be addressed to Airbus Customer Services through TechRequest on 
Airbus World, selecting Maintenance & Engineering Domain, Engineering Support Section and ATA 
29.
***BEG REV***
As per latest reporting policy (Ref to OIT 999.0018/16), “Action” 4.2.1’s inspection results (with or without 
findings) are to be addressed to Airbus Customer Services through the generic e-mail address:
inspection.results@airbus.com copy monitored.retrofit@airbus.com. 
***END REV***
Best Regards,
Christian FREMONT
VICE PRESIDENT ENGINEERING SUPPORT
CUSTOMER SERVICES
Marco MANTOVANI
SENIOR DIRECTOR A330/A340 PROGRAM
CUSTOMER SERVICES

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
