# Airbus All Operators Telex A300-55A6047

Copy: Revision 02 ("AOT A300-55A6047 Rev 02"), 7 pages: PDF https://openairdocs.org/files/sha256/3b/b9/3bb93c3ddb19e3d35f1b05f4e0671d8152492689205d015e920165962b43653e; text https://openairdocs.org/service-documents/airbus/aot-a300-55a6047/file/3bb93c3ddb19.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2010-0281; AD 2010-16-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Other document (All Operators Telex)
- Number: A300-55A6047
- Latest revision known: A300-55A6047, Revision 02, dated October 12, 2009 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus/aot-a300-55a6047

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2010-16-13](https://openairdocs.org/ad/2010-16-13.md), effective Sep 17, 2010: Revision 02

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus/aot-a300-55a6047/proposed.md).

## Text (7 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2010-0281; AD 2010-16-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

~6658365.txt
ALL OPERATORS TELEX - ALL OPERATORS TELEX
SUBJECT: A300-600 - ATA 55-40 - INSPECTION OF RUDDER SIDE SHELLS FOR
POTENTIAL SKIN TO HONEYCOMB DISBOND
OUR REF: AOT A300-55A6047 Rev 02 dated 12 OCT 09
OUR PREVIOUS REF: AOT A300-55A6047 Rev 01 dated 08 July 09
AOT A300-55A6047 Rev 00 dated 11 May 09
0. REASON FOR REVISION
This AOT has been revised to:
- Introduce an ultrasonic  inspection in the reinforced areas of the
rudders. This ultrasonic inspection replaces the thermographv
inspection required by AOT A300-55A6047 Rev.01 and as defined in the
specific Technical Dispositions for reinforced areas location A. The
chermography inspection requirements remain applicable in non-
reintorced areas as defineo  in the specific Technical Disposition
ror location D, F, G, H, J, K, L, M and N.
- Introduce minor  Changes in Technical Disposition
TD/K4/S1/27583/2009, now revised at issue E:
- References to the specific Technical Dispositions for
location A have been updated
- References to the specitic Technical Dispositions for
the "other areas" at location D, F, G, H, J, K, L, M and
have been included in appendix A.
- Titles of Dimensions of inspection drawings have been
revised (page 15).
- Reflect that the ELCh inspection at Trailing Edge area has to be
repeated twice at intervals not exceeding 4500 FC, but no less than
4000 FC since last inspection.
No additional work is required for rudders that have been inspected
through AOT A300-55A6047 Rev. 01 dated 08  July 09, except those on which
temporary option II or permanent vacuum loss hole restoration has been
performed  according to the specific Technical Dispositions at  Location
A: In this case, an additional Ultrasonic inspection within 4500 FC
from restoration date is required.
The revised paragraphs are indicated between **BEG.REV** and
**END.REV**.
1. AIRCRAFT AFFECTED
A11 A300-600
listed in Technical Disposition ret.
and having a honeycomb  core density of 24 kg/m3 (rudders
-icked "x" in column  "24kg core").
Or
A11 A300-600  aircratt equipped with rudders having the Serial Numbers
SN) listed in Technical Disposition ref. TD/K4/S1/27583/2009 issue E
Table -,  and having accumulated 13000 FC or more since their first
installation on aircraft at receipt date of this AOT.
Note: Affected rudders listed in Technical Disposition ref.
TD/K4/S1/27583/2009 issue E Table 1, having  a honeycomb  core density
greater than 24kg/m3 and having accumulated  less than 13000 FC at

### Page 2 (OCR)

~6658365. txt
receipt date of this AOT,  are also to be inspected according to the
AOT's instructions. However for these rudders the  accomplishment
then the 1g000 i threshodhis reaches to be considered from the date
a rudder originally fitted on one aircraft (refer to Aircraft
Inspection Report delivery document) has been removed and installed or
another aircraft,  it is the responsibility of the operator to apply the
required instructions contained in this AOT to the new aircraft.
If the cross-reference Rudder SN/ Aircraft MSN given in
TD/к4/s1/27583/2009 issue E Table 1 does not reflect the current status
or if the identification plate is missing, contact Airbus.
2. REFERENCED DOCUMENTATION
**BEG. REV**
REF.1: OIT 999.0092/08: ATA55 - Rudder side shell skin disbonding
REF. 2: A300-600  REF. 3: Technical Disposition Fef: TD/k4/$1/27583  TD/K4/S1/27583/2009 issue E
REF. 4. NTM 51-10-26  Part 7 (ELCh inspection)
REF 5: NTM 51-10-28 Part 7 (Vacuum Loss inspection)
REF 6: NTM 55-10-19 Part 5 (Tap test inspection)  10 (Thermography inspection)
REF 7: NTM 51-10-19
NTM 51-10-24 Part 4 - NTM Temporary Revision TR 51-006 based on
June 09 revision (Ultrasonic inspection)
**END. REV**
3. REASON
3.1 BACKGROUND
A deformation was visually detected on the rudder side shell of an A319
and an A321  _in-service aircraft. Both rudders were sent to Airbus
facilities for further analysis. A review of production records
revealed that the deformations reported on both rudders corresponded to
areas that had been reworked in production.
The conclusion of the investigation is that the disbonding most likely
not curing rework of the inner skin in production. this rework occurred  occurred as a consequence
outside autoclave.
such hot curing reworks were also performed on some A300-600 rudders.
Operators were informed thru OIT REF.1 dispatched in November 2008 and
revised in March 2009.
3.2 AIM
rudders that have been reworked in production with similar hot
curing process, this AOT calls for:
- a one-time Vacuum Loss inspection at rudder shell reinforced areas
- a three(3)-times repetitive Elasticity Laminate Checker (ELCh)
inspection at rudder  . shell trailing edge area
- a repetitive ELCh inspection in other rudder shell areas; until a
Vacuum Loss inspection is performed (considered as the terminating
action).
4. SHORT TERM ACTION
Page 2

### Page 3 (OCR)

~6658365. txt
4.1 PLANNING AND MANPOWER
This AOT is subject to an Airbus Monitored Retrofit Campaign. For
logistic purposes please provide in advance the inspection planning.
Your focal point for the planning and the logistics is:
wera  DIETZ, SEOTZ
Customer Services
Phone: +33 (0)5 67 19 14 22
Fax: +33 (0)5 61 93 27 45
Mailto: wera.dietz@airbus.com
4.1.1 ACCOMPLISHMENT TIMESCALE
Accomplishment timescale depends  on the locations of the  areas to be
inspected, which are fully described in Technical Disposition ref.
TD/K4/S1/27583/2009 issue E.
4.1.1.1 FOR REINFORCED AREAS
The one-time Vacuum Loss inspection described in paragraph 4.2.2.1 must
be performed within 8 months from the receipt date of this AOT.
**BEG.REV**
4.1.1.2 FOR TRAILING EDGE AREA
The ELCh inspection described in paragraph 4.2.2.2 must be performed
within 24 months from the receipt date of this AOT, and repeated twice
at intervals not exceeding 4500 FC but no less than 4000 FC since last
inspectio the third inspection without findings, no further action is  required in the trailing edge area.
**END. REV**
4.1.1.3 FOR OTHER AREAS (LOWER RIB/UPPER EDGE/LEADING EDGE/OTHER
LOCATIONS)
The repetitive ELCh inspection described in paragraph 4.2.2.3.A. must
be performed:
- within 8 months from the receipt date of this AOT
- then, repeated at intervals not exceeding 8 months
accomplishment of the terminating one-time Vacuum Loss
Accomplishment of this terminat ho nein faspection enoris the
epetitive inspection requirements described in paragraph 4.2.2.3.A.
If the vacuum loss inspection is performed within 8 months from the
receipt date of the AOT, no ELCh inspection is required before or
simultaneously.
4.1.2 MANPOWER
me manpower estimates given below are based on the direct labour to do
the work. These estimates assume that the work will be done bv
experienced personnel. They might need to be revised upwards to suit
operators' circumstances.
These estimates do not include the manpower required for repairs in
case of findings.
Page 3

### Page 4 (OCR)

~6658365.txt
A) Vacuum Loss inspection:
- Inspection: 1 man-hour per linear meter
- Hole restoration and resin curing time: 12 hours maximum elapsed
time.
B) ELCh inspection:
Note: Refer  to Technical Disposition ref. TD/K4/S1/27583/2009 issue E
for identification of inspection area:
- Location B: 4 man-hours
- Location C: 4 man-hours
- Location D: 1 man-hour
- Location E: 0.5 man-hours
- Location F: 3 man-hours.
4.2 DESCRIPTION
4.2.1 JOB PREPARATION AND ACCESS
Refer to Technical Disposition ref. TD/K4/S1/27583/2009 issue E
paragraph  'Job preparation"
4.2.2 INSPECTION INSTRUCTIONS
Rudder  shells must be inspected only in areas mentioned in Technical
Disposition ref. TD/K4/S1/27583/2009 issue E Table 1.
Example: Rudder SN TS-20/4 (end ot table 1)
This rudder must be inspected on  L/H side shell,
location only as per Technical Disposition
It must be inspected on R/H side shell, at trailing edge location only
as per Technical Disposition location C.
4.2.2.1 FOR REINFORCED AREA
Perform a one-time Vacuum Loss inspection according to Technical
Disposition ref.  TD/K4/S1/27583/2009 issue E location A.
Specific inspection instructions are to be requested by mail to:
Jean-Luc BOITEUX, SEES1
Customer Services
Phone: +33 (0)5 61 93 18 69
Malito: jean-luc.j.boiteux@airbus.com  +33 (0) 5 61 93 36 14
4.2.2.2 FOR TRAILING EDGE AREA
Perform three(3)-times repetitive ELCh inspection according to
Technical Disposition ref. TD/K4/S1/27583/2009 issue E location B, C,
C2, E and P.
4.2.2.3 FOR OTHER AREAS (LOWER RIB/UPPER EDGE/LEADING EDGE/OTHER
LOCATIONS)
A.) Perform a repetitive ELCh inspection according to Technical
Disposition ref. TD/K4/S1/27583/2009 issue E locations D, F, G, H, J,
K, L, M, N.
B.) Pertorm a one-time Vacuum Loss inspection according to specific
Technical Dispositions. In order to obtain these instructions, please
send a request to:
Jean-Luc BOITEUX, SEES1
Customer Services
Page 4

### Page 5 (OCR)

~6658365. txt
Phone: +33 (0)5 61 93 18 69
Fax: +33 (0)5 61 93 36 14
Mailto: jean-luc.j.boiteux@airbus.com
They will be provided in a time-frame compatible with the inspection
planning (refer to paragraph 4.1).
4.2.3 JOB CLOSE UP
Refer to Technical Disposition TD ref. TD/K4/S1/27583/2009 issue E
paragraph  "Job close up)'
4.2.4 ACTIONS IN CASE OF FINDINGS
sheet, and contact Airs at the following address before next flight  document accurately the relevant inspection report
to get further instructions:
SEER1/SEER2/SEER3
Customer Services
Fax: +33 (0)5 61 93 28 73
Mailto:
regionl.structurerepairSupport@airbus.com
region2.StructurerepairSupport@airbus.com
region3.StructureRepairSupport@airbus.com
or for AOG request
AIRTAC (Airbus Technical AOG Center)
Customer Services
Phone: +33 (0) 5 61 93 34 00
+33 (0) 5 61 93 35 00
Mailto: airtac@airbus.com
4.2.5 REPORTING
If there are no findings,  report to Airbus within 10 days from the
inspection date of each affected rudder, at the following address:
Jean-Luc BOITEUX, SEES1
Customer Services
Phone:  +33 (0) 5 61 93 18 69
Fax: +33 (0)5 61 93 36 14
Mailto: jean-luc.j.boiteux@airbus.com
**BEG.REV**
4.2.6 MATERIAL, TOOLING
Adjustable access platform or Cherry Picker
- Inspection equipment for ELCh as per REF.4
- Inspection equipment for Vacuum Loss inspection as per REF. 5
- Inspection equipment for Thermography as per REF. 6
- Inspection equipment for Tap test as per REF. 7
- Inspection equipment for Ultrasonic inspection as per REF. 8
**END. REV**
Note 1: In order for Airbus to provide adequate support to all affected
operators' ahead of the first scheduled inspection.  it is recommended to place a  Purchase Order for ELCh tool
two weeks
Note 2: A CD-Rom including ELCh familiarization has been shipped to all
Page 5

### Page 6 (OCR)

~6658365. txt
affected operators via Airbus Field Service stations.
**BEG. REV**
Note 3:  Instructions for  restoration of Vacuum Loss inspection holes
are detailed in the specific Technical Dispositions, and can be
(option I): Hole closing with selt-
nas to be ensured by freq months/500 FH (whichever otturs first),  Correct cover application
intervals not exceeding
until permanent restoration is performed,
- Temporary restoration (option II): Hole filling with resin.
Local ultrasonic inspection in reinforced areas and local
resin Injection. Final restoration has to be performed not later  inspection in other areas must be performed before
than 4500 FC.
- Permanent restoration: Hole filling with resin and restoration
of surface protection. Local ultrasonic inspection in reinforced
areas and local thermography inspection in other areas must be
performed before resin injection.
**END. REV**
Note 4: For thermography inspection, as a limited number of equipment
is available for loan  from Airbus,  necessary Infrared camera could also
be purchased at the following address:
FLIR SYSTEMS
Internet address: <http://www.flir.com/>
5. AOT APPROVAL
The technical content of this AOT has been approved under the authority
ot EASA Design Organization Approval number  EASA 21J.031.
It is anticipated that this AOT will be rendered mandatory.
6. REPORTING/ACKNOWLEDGMENT
Operators are requested to acknowledge receipt of this AoT within 48
hours after receipt to:
R. LASCOURS,
=-mail: richard.lascours@airbus.com
Fax number +33/ (0) 5.61.93.32.73
This acknowledgement can be made through the Airbus RCSM when
available.
Best regards,
E. VAN AELST
VICE PRESIDENT A300/A310/A300-600 PROGRAMME
CUSTOMER SERVICES DIRECTORATE
If you receive this message via e-mail/internet, we draw your attention
to the fact that it may be monitored and/or intercepted.
Page 6

### Page 7 (OCR)

~6658365. txt
Further, whilst Airbus has taken reasonable measures to ensure the
integrity of this message and its contents, no warranty, whether
express or implied, is given that the contents hereof conform to the
original. In case of any doubt, please retrieve this document from your
SITA address or Airbusworld or request that it be retransmitted by fax
or telex.
page 7

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
