# Airbus All Operators Transmission A310-55A2048

Copy: Revision 02 ("AOT 310-55A2048 Rev 02"), 7 pages: PDF https://openairdocs.org/files/sha256/a6/4b/a64bdb9c12c8662873f831dd80e26136d35adbd2a898f40c0d2c8d64586d309e; text https://openairdocs.org/service-documents/airbus/aot-a310-55a2048/file/a64bdb9c12c8.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2010-0281; AD 2010-16-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Other document (All Operators Transmission)
- Number: A310-55A2048
- Latest revision known: A310-55A2048, Revision 02, dated October 12, 2009 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus/aot-a310-55a2048

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2010-16-13](https://openairdocs.org/ad/2010-16-13.md), effective Sep 17, 2010: Revision 02

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus/aot-a310-55a2048/proposed.md).

## Text (7 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2010-0281; AD 2010-16-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

~9719384.txt
ALL OPERATORS TELEX - ALL OPERATORS TELEX
SUBJECT: A31O - ATA S0-40 - INSPECTION OF RUDDER SIDE SHELLS FOR
POTENTIAL SKIN TO HONEYCOMB DISBOND
OUR REF: AOT A310-55A2048 Rev 02 dated 12 OCT 09
OUR PREVIOUS REF: AOT A310-55A2048 Rev 01 dated 08 July 09
AOT A310-55A2048 Rev 00 dated 11 May 09
0. REASON FOR REVISION
This AOT has been revised to:
- Introduce an ultrasonic inspection in the reinforced areas of the
rudders. This ultrasonic inspection replaces the thermography
inspection required by AOT A310-55A2048 Rev. 01 and as defined ir
the specific Technical Dispositions for reinforced areas location
. The thermography inspection requirements remain applicable ir
areas as defined in the specific Technical
Dispositions for location D, F, G,  M and N.
- Introduce minor changes in Technical
TD/K4/S1/27583/2009, now revised
- References to the specific Technical Dispositions for location
A have been updated
- References to the specific Technical Dispositions for the
"other areas"  at location D, F, G, H, J, K, L, M and N have
been included in appendix A.
- Titles of Dimensions of inspection drawings have been revised
(page 15) .
- Reflect  that the  ELCh inspection at Trailing Edge area has to be
repeated twice at intervals not exceeding 4500 FC, but no less
than 4000 FC since last inspection.
No additional work is required for rudders that have been inspected
through AOT A310-55A2048 Rev.01 dated 08 July 09, except those  on which
temporary option II or permanent vacuum loss hole restoration has been
performed according to the specific Technical Dispositions at Location
A: In this case, an  additional Ultrasonic inspection within 4500 FC
from restoration date is required.
The revised paragraphs are indicated between **BEG.REV** and
**END. REV**.
1. AIRCRAFT AFFECTED
All A310 aircraft equipped with rudders having the Serial Numbers (SN)
listed in Technical Disposition ref. TD/K4/S1/27583/2009 issue E Table
-, and having a honeycomb core density of 24 kg/m3 (rudders ticked "x"
in column "24kg core
or
All A310 aircraft equipped with rudders having the Serial Numbers (SN)
listed in Țechnical Disposition ref. TD/K4/S1/27583/2009 issue E Table
1, and having accumulated 13000 FC or more since their first
installation on aircraft at receipt date of this AOT.
Note: Affected rudders listed in Technical Disposition ref.
TD/K4/S1/27583/2009 issue E Table 1, having a honeycomb core density
greater than 24kg/m3 and having  accumulated less than 13000 FC at
receipt date of this AOT, are also to be inspected according to the

### Page 2 (OCR)

~9719384.txt
AOT's instructions. However for these rudders the  accomplishment
timescale given  paragraph 4.1.1 has to be considered from the date
when the 13000 FC threshold is reached.
**BEG. REV**
The tollowing rudders that have been inspected through the sampling
campaign,  inspected at trailing edge location, in
accordance with this AOT.
SN HF-1059
SN HF-1087
must be perred within 450 ic from despisent or the sampling
inspection,  and repeated one time at an interval not exceeding 4500 FC,
but no less than 4000 FC since last inspection.
**END. REV**
Insation er delive demen are trive a fatal th  another aircraft,  responsibility of the operator to apply the
required instructions contained in this AOT to the new aircraft.
If the cross-reference Rudder SN/ Aircraft MSN given ir
TD/K4/S1/27583/2009 issue E Table 1 does not reflect the current status
or if the identification plate is missing, contact Airbus.
2. REFERENCED DOCUMENTATION
**BEG. REV**
REF.1: OIT 999.0092/08: ATA55 - Rudder side shell Skin disbonding
REF.2: A310 SRM  55-41-12 Fig. 1 item 10 & 15
REF.3: Technical Disposition ref.  .TD/K4/S1/27583/2009 issue E
REF.4. NTM 51-10-26 Part 7 (ELCh inspection)
REF 5: NTM 51-10-28 Part 7 (Vacuum Loss inspection)
REF 6: NTM 55-40-02 Part 10 (Thermography inspection)
REF 7: NT 51-10-19 Part 5 (Tap test inspection)
REF 8: NTM 51-10-24 Part 4 - NTM Temporary Revision TR 51-006 based on
June 09 revision (Ultrasonic inspection).
**END. REV**
3. REASON
3.1 BACKGROUND
A deformation was visually detected on the rudder side shell of an A319
and an A321 in-service aircraft. Both rudders were sent to Airbus
facilities for further analysis. A review of production records
revealed that the deformations reported on both rudders corresponded to
areas that had been reworked in production.
The conclusion of the investigation is that the disbonding most likely
occurred as a consequence
ot curina rework of  the inner skin in production.
outside the autoclave.
such hot curing reworks were also performed on some A310 rudders
Operators were informed thru OIT REF. 1 dispatched in November 2008 and
revised in March 2009.
3.2 AIM
Page 2

### Page 3 (OCR)

~9719384.txt
For rudders that have been reworked in production with similar hot
curing process, this AOT calls for:
- a one-time Vacuum Loss inspection at rudder shell reinforced areas
- a three(3)-times repetitive Elasticity Laminate Checker (ELCh)
inspection at rudder shell trailing edge area
- a repetitive ELCh inspection in other rudder shell areas; until a
Vacuum Loss inspection is performed (considered as the terminating
4. SHORT TERM ACTION
4.1 PLANNING AND MANPOWER
This AOT is subject to an Airbus Monitored Retrofit Campaign. For
logistic purposes please provide in advance the inspection planning.
Your focal point for the planning and the logistics is:
DIETZ, SEOT2
Customer Services
Phone: +33 (0) 5 67 19 14 22
Fax: +33 (0) 5 61 93 27 45
Mailto: wera.dietz@airbus.com
4.1.1 ACCOMPLISHMENT TIMESCALE
Accomplishment timescale depends  on the locations of the  areas to be
inspected,  which are fully  described in Technical Disposition ref.
TD/K4/S1/27583/2009 issue E.
4.1.1.1 FOR REINFORCED AREAS
The one-time Vacuum Loss inspection described in paragraph 4.2.2.1 must
be performed within 8 months from the receipt date of this AOT.
**BEG.REV**
4.1.1.2 FOR TRAILING EDGE AREA
The ELCh inspection described in paragraph 4.2.2.2 must be pertormed
within 24 months from the receipt date of this AOT, and repeated twice
at intervals not exceeding 4500 FC, but no less than 4000 FC since last
fos lowing the third inspection without findings, no further action is
required in the trailing edge area.
**END. REV**
4.1.1.3 FOR OTHER AREAS (LOWER RIB/UPPER EDGE/LEADING EDGE/OTHER
LOCATIONS)
The repetitive ELCh inspection described in paragraph 4.2.2.3.A. must
be performed:
- within 8 months from the receipt date of this AOT
- then, repeated at intervals not exceeding 8 months
accomplishment of the terminating one-time Vacuum Loss
inspection mentioned in paragraph 4.2.2.3.B., that must be pertormec
within 24 months from the receipt date of this AOT.
Accomplishment of this terminating one-time inspection cancels the
repetitive ELCh inspection requirements described in paragraph
4.2.2.3.A.
If the vacuum loss inspection is performed within 8 months from the

### Page 4 (OCR)

~9719384. txt
receipt date of the AOT, no ELCh inspection is required before or
simultaneously.
4.1.2 MANPOWER
The manpower estimates given below are based on the direct labour to do
the work. These estimates assume  that the work will be done by
experienced personnel. They might need to be revised upwards to suit
operators' circumstances.
These estimates do not include the manpower required for repairs in
case of findings.
A) Vacuum Loss inspection:
- Inspection:  1 man-hour per linear meter
- Hole restoration and resin curing time: 12 hours maximum elapsed
B) ELCh inspection:
Note: Refer to Technical Disposition ref. TD/K4/S1/27583/2009 issue E
for identification of inspection
- Location B: 4 man-hours
- Location C: 4 man-hours
- Location D: 1 man-hour
- Location E : 0.5 man-hours
- Location F  : 3 man-hours
Figures are given for one side shell to be inspected.
4.2 DESCRIPTION
4.2.1 JOB PREPARATION AND ACCESS
Refer to Technical Disposition ref. TD/K4/S1/27583/2009 issue E
paragraph  "Job preparation"
4.2.2 INSPECTION INSTRUCTIONS
Rudder shells must be inspected only in areas mentioned in Technical
Disposition ref. TD/K4/S1/27583/2009 issue E Table 1.
Example:  Rudder SN TS-2074 (end of table 1)
This rudder must be inspected on L/H side shell,  at trailing edge
location only as per Technical Disposition location C.
as per Technical Disposition location C.  It must be inspected on R/H side shell  at trailing edge location only
4.2.2.1 FOR REINFORCED AREA
Perform a one-time Vacuum Loss inspection according to Technical
Disposition ref.  TD/K4/S1/27583/2009 issue E location A.
Specific inspection instructions are to be requested by mail to:
Jean-Luc BOITEUX, SEES1
Customer Services
Phone: +33 (0)5 61 93 18 69
Fax: +33 (0) 5 61 93 36 14
Mailto: jean-luc.j.boiteux@airbus.com
4.2.2.2 FOR TRAILING EDGE AREA
perform three(3)-times repetitive ELCh inspection according to
Technical Disposition ref. TD/K4/S1/27583/2009 issue E location B, C,
CL, E and P.
Page 4

### Page 5 (OCR)

~9719384.txt
4.2.2.3 FOR OTHER AREAS (LOWER RIB/UPPER EDGE/LEADING EDGE/OTHER
LOCATIONS)
A. Pertorm a repetitive ELCh inspection according  to Technical
Disposition ref. TD/K4/S1/27583/2009 issue E locations D, F, G, H, J,
K, L, M, N.
B.) Perform  a one-time Vacuum Loss inspection according to specific
Technical Dispositions. In order to obtain these instructions, please
send a request to:
Jean-LuC BOITEUX, SEES1
Customer Services
Phone: +33 (0) 5 61 93 18 69
Malito: jean-luc.j.boiteux@airbus.com  61 93  36 14
They will be provided in a time-frame compatible with the inspection
planning (refer to paragraph 4.1).
4.2.3 JOB CLOSE UP
Refer to Technical Disposition TD ref. TD/K4/S1/27583/2009 issue E
paragraph  "Job close up)".
4.2.4 ACTIONS IN CASE OF FINDINGS
In case of findings,  document accurately the relevant inspection report
sheet,  and contact Airbus at the following address before next flight
to get further instructions:
SEER1/SEER2/SEER3
Customer Services
Fax: +33 (0)5 61 93 28 73
regionl.StructureRepairSupport@airbus.com
region2.StructurerepairSupport@airbus.com
region3.StructureRepairSupport@airbus.com
Or for AOG request
AIRTAC (Airbus Technical AOG Center)
Customer  Services
Phone: +33 (0) 5 61 93 34 00
Fax: +33 (0)5 61 93 35 00
Mailto: airtac@airous.com
4.2.5 REPORTING
If there are no findings,  report to Airbus within 10 days from the
inspection date of each affected rudder, at the following address:
Jean-Luc BOITEUX, SEES1
Customer Services
Phone: +33 (0)5 61 93 18 69
Fax: +33  (0)5 61 93 36 14
Mailto: jean-luc.j.boiteux@airbus.com
**BEG. REV**
4.2.6 MATERIAL, TOOLING
Adjustable access platform or Cherry Picker
Page 5

### Page 6 (OCR)

~9719384.txt
- Inspection equipment for ELCh as per REF.4
- Inspection equipment for Vacuum Loss inspection as per REF. 5
- Inspection equipment for Thermography as per REF. 6
- Inspection equipment for Tap test as  per REF. 7
- Inspection equipment for Ultrasonic inspection as per REF. 8.
**END. REV**
Note 1: In order for Airbus to provide adequate support to all affected
operators,  it is recommended to place a  Purchase Order for ELCh tool
two weeks  ahead of the first scheduled inspection.
Note 2: A CD-Rom including ELCh familiarization has been shipped to all
affected operators via Airbus Field Service stations.
**BEG.REV**
Note 3: Instructions for  restoration of Vacuum Loss inspection holes
are detailed in the specific Technical Dispositions, and can be
performed in 2 steps:
patches' by  - Temporary restoration (option I): Hole closing with self-adhesive  valid for 4500 FC. Correct cover application has to be
frequent detailed visual inspections at intervals not
exceeding 4 months/500 FH (whichever occurs first), until permanent
reasona inspection in retioned areas fnd local thermography
inspection in other areas must be performed before resin injection.
Final restoration has to be performed not later than 4500 FC.
End focal renogray inspection in Other areas use be peroned.
before resin injection.
**END. REV**
Note 4:  _For thermography inspection, as a limited number of equipment
is available for loan from Airbus, necessary Infrared camera could also
be purchased at the following address:
FLIR SYSTEMS
Internet address: <http://www.flir.com/>
5. AOT APPROVAL
The technical content of this AOT has been approved under the authority
† EASA Design Organization Approval number EASA 21J.031.
t is anticipated that this AOT will be rendered mandatory.
6. REPORTING/ACKNOWLEDGMENT
Operators are requested to acknowledge receipt of this AOT within 48
hours after receipt to:
R. LASCOURS, SEE
E-mail: richard.lascours@airbus.com
Fax number +33/ (0) 5.61.93.32.73
This  acknowledgement can be made through the Airbus RCSM when
available.
Page 6

### Page 7 (OCR)

~9719384.txt
Best regards,
E. VAN AELST
VICE PRESIDENT A300/A310/A300-600 PROGRAMME
CUSTOMER SERVICES DIRECTORATE
If you receive this message via e-mail/internet, we draw your attention
to the fact that it may be monitored and or intercepted.
Further, whilst Airbus has taken reasonable measures to ensure the
integrity of this message and its contents, no warranty, whether
express or implied,  is given that the contents hereof conform to the
original. In case of any doubt,  please retrieve this document from your
SITA address or Airbusworld system or request that it be retransmitted
by fax or telex.
Page 7

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
