# Airbus All Operators Transmission A320-55A1038

Copy: U.S. DOT/FAA - AOT-55A1038-00 ("U.S. DOT/FAA - AOT-55A1038-00"), 6 pages: PDF https://openairdocs.org/files/sha256/97/d3/97d3dd16b455f965d391fee648408a3e165236381203bfee6e66d21e8313556c; text https://openairdocs.org/service-documents/airbus/aot-a320-55a1038/file/97d3dd16b455.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2012-1034; AD 2013-05-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Other document (All Operators Transmission)
- Number: A320-55A1038
- Latest revision known: A320-55A1038, Revision 02, dated September 28, 2009 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus/aot-a320-55a1038

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2013-05-11](https://openairdocs.org/ad/2013-05-11.md), effective Jul 26, 2013: Revisions 01 and 02
- [AD 2010-23-07](https://openairdocs.org/ad/2010-23-07.md), effective Dec 10, 2010: Revisions 01 and 02

Also cited in [2 proposed ADs](https://openairdocs.org/service-documents/airbus/aot-a320-55a1038/proposed.md).

## Text (6 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2012-1034; AD 2013-05-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ALL OPERATORS TELEX - ALL OPERATORS TELEX
SUBJECT: A318/A319/A320/A321 - ATA 55-40 - INSPECTION OF RUDDER SIDE
SHELLS FOR POTENTIAL SKIN TO HONEYCOMB DISBOND
OUR REF: AOT A320-55A1038 dated 22 April 09
1. AIRCRAFT AFFECTED
All A318/A319/A320/A321 aircraft equipped with rudders having the
Serial Numbers (SN) listed in Technical Disposition ref.
TD/K4/S2/27086/2009 issue C Table 1, and having a honeycomb core
density of 24 kg/m3 (rudders ticked "x" in column "24kg core").
 Or
All A318/A319/A320/A321 aircraft equipped with rudders having the
Serial Numbers (SN) listed in Technical Disposition ref.
TD/K4/S2/27086/2009 issue C Table 1, and having accumulated 20000 FC
or more at receipt date of this AOT.
Note: Affected rudders having accumulated less than 20000 FC at
receipt date of this AOT will be inspected through a forthcoming
dedicated Inspection Service Bulletin planned to be issued by end of
May 2009.
The following rudders that have been inspected through the sampling
campaign, do not need to be inspected as per this AOT:
 SN TS-2359MSN 998AFR
 SN TS-1096MSN 94DLH
 SN TS-1149MSN 147DLH
The following rudder that has been inspected through the sampling
campaign, is only to be inspected at trailing edge location, in
accordance with this AOT.
 SN TS-1536MSN 533CCM
For this rudder, the ELCh inspection described in paragraph 4.2.2.2
must be performed within 4500 FC from accomplishment of the sampling
inspection, and repeated one time at an interval not exceeding 4500
FC.
In case a rudder originally fitted on one aircraft (refer to Aircraft
Inspection Report delivery document) has been removed and installed
on another aircraft, it is the responsibility of the operator to
apply the required instructions contained in this AOT to the new
aircraft.
If the cross-reference Rudder SN/ Aircraft MSN given in
TD/K4/S2/27086/2009 issue C Table 1 does not reflect the current
status, contact Airbus.
2. REFERENCED DOCUMENTATION
REF.1: OIT 999.0092/08: ATA55 – Rudder side shell skin disbonding
REF.2: A318/A319/A320/A321 SRM 55-41-13 Fig. 1 item 1 and item 5
REF.3: Technical Disposition ref. TD/K4/S2/27086/2009 issue C
REF.4. NTM TASK 51-10-26-220-801 – Temporary Revision TR 51-003 (ELCh
inspection)
REF 5: NTM TASK 51-10-28-220-801 – Temporary Revision TR 51-002
(Vacuum Loss inspection)
REF 6: NTM TASK 51-10-25-290-801 or TASK 51-10-25-290-802
(Thermography inspection)

### Page 2

REF 7: NTM TASK 51-10-19-280-801 (Tap test inspection)
3. REASON
3.1 BACKGROUND
A deformation was visually detected on the rudder side shell of an
A319 and an A321 in-service aircraft. Both rudders were sent to
Airbus facilities for further analysis.
A review of production records revealed that the deformations
reported on both rudders corresponded to areas that had been reworked
in production.
The conclusion of the investigation is that the disbonding most
likely occurred as a consequence of excessive temperature applied,
during a hot curing rework of the inner skin in production. This
rework occurred outside the autoclave.
Operators were informed thru OIT REF.1 dispatched in November 2008
and revised in March 2009.
3.2 AIM
For rudders that have been reworked in production with similar hot
curing process, this AOT calls for:
-a one-time Vacuum Loss inspection at rudder shell reinforced
areas
-a three(3)-times repetitive ELCh inspection at rudder shell
trailing edge area
-a repetitive ELCh inspection in other rudder shell areas; until
a Vacuum Loss inspection is performed (considered as the
terminating action)
4. SHORT TERM ACTION
4.1 PLANNING AND MANPOWER
This AOT is subject to an Airbus Monitored Retrofit Campaign. For
logistic purposes please provide in advance the inspection planning.
Your focal point for the planning and the logistics is:
Wera DIETZ, SEOT2,
Customer Services
Phone: +33 (0)5 67 19 14 22
Fax: +33 (0)5 61 93 27 45
Mailto: wera.dietz@airbus.com
4.1.1 ACCOMPLISHMENT TIMESCALE
Accomplishment timescale depends on the locations of the areas to be
inspected, which are fully described in Technical Disposition ref.
TD/K4/S2/27086/2009 issue C.
4.1.1.1 FOR REINFORCED AREAS
The one-time Vacuum Loss inspection described in paragraph 4.2.2.1
must be performed within 200 days from the receipt date of this AOT.
4.1.1.2 FOR TRAILING EDGE AREA
The ELCh inspection described in paragraph 4.2.2.2 must be performed
within 20 months from the receipt date of this AOT, and repeated two
times at intervals not exceeding 4500 FC.
Further to the third inspection without findings, no further action

### Page 3

is required as per this AOT.
4.1.1.3 FOR OTHER AREAS (SPLICE/LOWER RIB/UPPER EDGE/LEADING
EDGE/OTHER LOCATIONS)
The repetitive ELCh inspection described in paragraph 4.2.2.3.A. must
be performed:
-within 200 days from the receipt date of this AOT
-then, repeated at intervals not exceeding 1500 FC / 200 days
(whichever occurs first)
-up to accomplishment of the terminating one-time Vacuum Loss
inspection mentioned in paragraph 4.2.2.3.B., that must be
performed within 20 months from the receipt date of this AOT.
Accomplishment of this terminating one-time inspection cancels
the repetitive ELCh inspection requirements described in
paragraph 4.2.2.3.A.
4.1.2 MANPOWER
The manpower estimates given below are based on the direct labour to
do the work. These estimates assume that the work will be done by
experienced personnel. They might need to be revised upwards to suit
operators' circumstances.
These estimates do not include the manpower required for repairs in
case of findings.
A) Vacuum Loss inspection:
-Inspection: 1 man-hour per linear meter
-Hole restoration and resin curing time: 12 hours maximum
elapsed time
B) ELCh inspection:
Note: Refer to Technical Disposition ref. TD/K4/S2/27086/2009 issue C
for identification of inspection area:
-Location B: 4 man-hours
-Location C: 2 man-hours
-Location D: 1 man-hour
-Location E : 0.5 man-hours
-Location F : 2 man-hours
Figures are given for one side shell to be inspected.
4.2 DESCRIPTION
4.2.1 JOB PREPARATION AND ACCESS
Refer to Technical Disposition ref. TD/K4/S2/27086/2009 issue C
paragraph "Job preparation".
4.2.2 INSPECTION INSTRUCTIONS
Rudder shells must be inspected only in areas mentioned in Technical
Disposition ref. TD/K4/S2/27086/2009 issue C Table 1.
Example: Rudder SN TS-2205 (end of table 1)
This rudder must be inspected on L/H side shell, at trailing edge
location as per Technical Disposition location B. Other areas are not
to be inspected.
It must be also inspected on R/H side shell, at lower rib location as
per Technical Disposition location D. Other areas are not to be
inspected.
4.2.2.1 FOR REINFORCED AREA
Perform a one-time Vacuum Loss inspection according to Technical
Disposition ref. TD/K4/S2/27086/2009 issue C location A.

### Page 4

Specific inspection instructions are to be requested by mail to:
Nicolas SEYNAEVE, SEES1
Customer Services
Phone: +33 (0)5 61 93 34 38
Fax: +33 (0)5 61 93 36 14
Mailto: nicolas.seynaeve@airbus.com
4.2.2.2 FOR TRAILING EDGE AREA
Perform three(3)-times repetitive ELCh inspection according to
Technical Disposition ref. TD/K4/S2/27086/2009 issue C location B.
4.2.2.3 FOR OTHER AREAS (SPLICE/LOWER RIB/UPPER EDGE/LEADING
EDGE/OTHER LOCATIONS)
A.) Perform a repetitive ELCh inspection according to Technical
Disposition ref. TD/K4/S2/27086/2009 issue C locations C, D, E, F, G
and H.
B.) Perform a one-time Vacuum Loss inspection according to specific
Technical Dispositions. In order to obtain these instructions, please
send a request to:
Nicolas SEYNAEVE, SEES1
Customer Services
Phone: +33 (0)5 61 93 34 38
Fax: +33 (0)5 61 93 36 14
Mailto: nicolas.seynaeve@airbus.com
They will be provided in a time-frame compatible with the inspection
planning (refer to paragraph 4.1).
4.2.3 JOB CLOSE UP
Refer to Technical Disposition TD ref. TD/K4/S2/27086/2009 issue C
paragraph "Job close up)".
4.2.4 ACTIONS IN CASE OF FINDINGS
In case of findings, document accurately the relevant inspection
report sheet, and contact Airbus at the following address before next
flight to get further instructions:
SEER1/SEER2/SEER3
Customer Services
Fax: +33 (0)5 61 93 28 73
Mailto:
region1.StructureRepairSupport@airbus.com
region2.StructureRepairSupport@airbus.com
region3.StructureRepairSupport@airbus.com
Or for AOG request:
AIRTAC (Airbus Technical AOG Center)
Customer Services
Phone: +33 (0)5 61 93 34 00
Fax: +33 (0)5 61 93 35 00
Mailto: airtac@airbus.com
4.2.5 REPORTING
If there are no findings, report to Airbus within 10 days from the
inspection date of each affected rudder, at the following address:
Nicolas SEYNAEVE, SEES1

### Page 5

Customer Services
Phone: +33 (0)5 61 93 34 38
Fax: +33 (0)5 61 93 36 14
Mailto: nicolas.seynaeve@airbus.com
4.2.6 MATERIAL, TOOLING
-Adjustable access platform or Cherry Picker
-Inspection equipment for ELCh as per REF.4
-Inspection equipment for Vacuum Loss inspection as per REF. 5
-Inspection equipment for Thermography as per REF. 6
-Inspection equipment for Tap test as per REF. 7
Note 1: In order for Airbus to provide adequate support to all
affected operators, it is recommended to place a Purchase Order for
ELCh tool two weeks ahead of the first scheduled inspection.
Note 2: A CD-Rom including ELCh familiarization has been shipped to
all affected operators via Airbus Field Service stations.
Note 3: Instructions for restoration of Vacuum Loss inspection holes
are detailed in the specific Technical Dispositions, and can be
performed in 2 steps:
-Temporary restoration: Hole closing with self-adhesive patches,
allowed for 4500 FC
-Permanent restoration: Hole filling with resin and restoration
of surface protection. Local thermography inspection is
required before resin injection, to ensure sandwich structure
is free of liquid.
Note 4: For thermography inspection, as a limited number of equipment
is available for loan from Airbus, necessary Infrared camera could
also be purchased at the following address:
FLIR SYSTEMS
Internet address: <http://www.flir.com/>
5. AOT APPROVAL
The technical content of this AOT has been approved under the
authority of EASA Design Organization Approval number EASA 21J.031.
It is anticipated that this AOT will be rendered mandatory.
6. REPORTING/ACKNOWLEDGMENT
Operators are requested to acknowledge receipt of this AOT within 48
hours after receipt to:
MR. R. LASCOURS, SEE,
SITA CODE TLSBT7X,
FAX: +33 / (0) 5 61 30 00 79
This acknowledgement can be made through the Airbus RCSM when
available.
Best regards,
A. VIEILLARD
VICE PRESIDENT A318/A319/A320/A321 PROGRAMME
CUSTOMER SERVICES DIRECTORATE
If you receive this message via e-mail/internet, we draw your
attention to the fact that it may be monitored and/or intercepted.
Further, whilst Airbus has taken reasonable measures to ensure the

### Page 6

integrity of this message and its contents, no warranty, whether
express or implied, is given that the contents hereof conform to the
original. In case of any doubt, please retrieve this document from
your SITA address or AirbusWorld or request that it be retransmitted
by fax or telex.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
