# Airbus All Operators Transmission A32L003-14

Copy: No revision named ("U.S. DOT/FAA - AOT-A32L003-14"), 5 pages: PDF https://openairdocs.org/files/sha256/4b/2e/4b2eb27a4ec29a73a8be7577fee909e1c226eaaff91b4fa24a7905487906b7b8; text https://openairdocs.org/service-documents/airbus/aot-a32l003-14/file/4b2eb27a4ec2.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2014-0584; AD 2015-10-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Other document (All Operators Transmission)
- Number: A32L003-14
- Page: https://openairdocs.org/service-documents/airbus/aot-a32l003-14

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2015-10-03](https://openairdocs.org/ad/2015-10-03.md), effective Jul 6, 2015: No revision named
- [AD 2014-09-05](https://openairdocs.org/ad/2014-09-05.md), effective May 14, 2014: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus/aot-a32l003-14/proposed.md).

## Text (5 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2014-0584; AD 2015-10-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

CUSTOMER SERVICES DIRECTORATE 
1 ROND POINT MAURICE BELLONTE 
31707 BLAGNAC CEDEX FRANCE 
TELEPHONE + 33 (0)5 61 93 33 33 
 
ALERT OPERATORS TRANSMISSION - AOT
AOT ref: A32L003-14 Page 1 of 5 Date: 10 Mar 2014 
© AIRBUS S.A.S. 2014. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT 
 
 
SUBJECT: ATA 32 – MAIN LANDING GEAR (MLG) SIDESTAY UPPER CARDAN PIN INSPECTION 
  
 
AIRCRAFT TYPE: A330, A340. 
 
 
OUR REF.:  A32L003-14 dated 10 Mar 2014. 
 
 
1. AIRCRAFT AFFECTED 
 
A330-200/300 and A340-200/300 fitted with: 
- Basic MLG (PN 20125 series) with sidestay upper cardan pin PN 201267202 
- Growth MLG (PN 20149 series) with sidestay upper cardan pin PN 201483202. 
 
Note: aircraft fitted with Enhanced MLG (PN 10-210 series) are not subject to the inspection detailed 
in this AOT. 
 
 
2. REFERENCED DOCUMENTATION 
 
2.1 APPENDIX 
 
- Appendix 1 MLG Sidestay cardan pin clearances 
- Appendix 2 Inspection reporting sheet 
- Appendix 3 Flow Chart 
 
2.2 REFERENCES 
 
- Ref. 1: AMM 32-11-16-420-053 
- Ref. 2: IPC 32-11-18-01 
- Ref. 3: MBD CMM 32-11-91, Figure 1 
- Ref. 4: MBD CMM 32-12-07, Figure 1 
- Ref. 5: AMM 32-11-18-000-801-A & 32-11-18-400-801-A 
 
 
3. REASON 
 
The purpose of this AOT is to request operators to accomplish an inspection on the MLG sidestay upper 
cardan pin. 
 
 
3.1 FACTS 
 
An A330 fitted with Basic MLG was rolling out after landing when it experienced a nose wheel steering 
fault (unrelated to the migration detailed in this document) , which resulted in the crew stopping the 
aircraft on the taxiway after vacating the runway.  
 
Inspection identified that the RH MLG sidestay upper cardan pin (Ref. 2) had migrated out of position. 
The sidestay upper cardan nut and retainer were found in the landing gear bay detached from the upper 
cardan pin. The nut and the retainer were still bolted together.

### Page 2

CUSTOMER SERVICES DIRECTORATE 
1 ROND POINT MAURICE BELLONTE 
31707 BLAGNAC CEDEX FRANCE 
TELEPHONE + 33 (0)5 61 93 33 33 
 
ALERT OPERATORS TRANSMISSION - AOT
AOT ref: A32L003-14 Page 2 of 5 Date: 10 Mar 2014 
© AIRBUS S.A.S. 2014. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT 
 
 
3.2 CONSEQUENCES 
 
The loss of the sidestay cardan pin locking function (loss of nut) could lead to a complete migration of 
the sidestay upper cardan pin and a disconnection of the sidestay upper arm from the aircraft structure. 
This could therefore lead to a landing gear collapse. 
 
 
3.3 AIM 
 
The aim of this AOT is to request operators to: 
 
- Perform a Detailed Inspection (DI) of the upper cardan pin and nut and retainer 
 
- Perform a Gap check of the upper cardan pin and nut 
 
The accomplishment of these inspections is requested on aircraft fitted with MLG sidestay upper cardan 
pins which have accumulated more than 8 years since first overhaul and which have not yet gone 
through their second overhaul, at the issue date of this AOT. 
 
 
4. SHORT TERM ACTION 
 
4.1 PLANNING AND MANPOWER 
 
4.1.1 ACCOMPLISHMENT TIMESCALE 
 
A330-200/300 and A340-200/300 fitted with MLG sidestay upper cardan pins PN 201267202 & 
201483202 which have accumulated more than 8 years since first overhaul and which have not yet 
gone through their second overhaul, at the issue date of this AOT, are subject to the following 
inspections: 
 
1. The accomplishment of the DI mentioned in Para 4.2.2.1 must be performed no later than 30 
days after the issuance of this AOT.  
2. Repeat the DI mentioned in Para 4.2.2.1 every 10 days until a gap check as per Para 4.2.2.2 
is performed. 
3. Perform a gap check as mentioned in Para 4.2.2.2 no later than 4 months after issuance of 
this AOT. 
 
When a gap check is performed, the results (including nil findings) must be reported to Airbus using 
the proforma provided in Appendix 2 of this AOT. 
 
 
4.2 DESCRIPTION 
 
4.2.1 ACCESS 
 
The Detailed Inspection and the gap check called for in this AOT do not require special access, 
equipment, or aircraft jacking.  
 
 
4.2.2 INSPECTION REQUIREMENTS 
 
- 4.2.2.1 Detailed Inspection:

### Page 3

CUSTOMER SERVICES DIRECTORATE 
1 ROND POINT MAURICE BELLONTE 
31707 BLAGNAC CEDEX FRANCE 
TELEPHONE + 33 (0)5 61 93 33 33 
 
ALERT OPERATORS TRANSMISSION - AOT
AOT ref: A32L003-14 Page 3 of 5 Date: 10 Mar 2014 
© AIRBUS S.A.S. 2014. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT 
 
 
Carry out a DI of the Upper Cardan Pin and retainer and nut assembly, ensuring that there is 
no pin chrome visible inboard of the wing rear spar fitting lug, and that the nut and locking 
device (including bolts and washers), are still in place. There is no requirement to remove the 
nut, pin and retainer at this stage. 
 
 
Migrated upper cardan pin. 
 
 
- 4.2.2.2 Gap check: 
 
WARNING: MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING NOTICES 
ARE IN A POSITION BEFORE YOU START A TASK ON OR NEAR: 
 THE FLIGHT CONTROLS 
 THE FLIGHT CONTROL SURFACES 
 THE LANDING GEAR AND THE RELATED DOORS  
 COMPONENTS THAT MOVE 
MOVEMENT OF COMPONENTS CAN KILL OR INJURE PERSONS. 
 
(a) Ensure that no gap exists between wing rear spar fitting lugs (outboard & inboard lugs) 
and their installed bush flanges (no bush migration). Refer to Appendix 1 and report  in 
Appendix 2. 
 
(b) Measure MLG Cardan Pin clearance dimensions X plus Y, which must be no greater than 
0.6 mm (0.0236 in.). Take largest gap measured at 3 points circumferentially. Refer to 
Appendix 1 or to Ref.1 Fig ‘Cardan Pin - Clearances’ SHEET 1. 
 
(c) Repeat Gap check on the opposite side landing gear. 
 
(d) Record all measurements. 
 
(e) Report findings including measured gap dimensions (refer to Appendix 2)  
 
Example:   
Dim X (maximum gap measured between head of cardan pin and bush = 0.2 mm 
Dim Y (maximum gap measured between nut and bush) = 0.35mm 
Total Gap = Dim X + Dim Y = 0.55mm.  
Recorded gap measurement = 0.55mm.

### Page 4

CUSTOMER SERVICES DIRECTORATE 
1 ROND POINT MAURICE BELLONTE 
31707 BLAGNAC CEDEX FRANCE 
TELEPHONE + 33 (0)5 61 93 33 33 
 
ALERT OPERATORS TRANSMISSION - AOT
AOT ref: A32L003-14 Page 4 of 5 Date: 10 Mar 2014 
© AIRBUS S.A.S. 2014. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT 
 
 
4.2.3 FINDINGS 
 
For the DI: 
 
- If pin chrome found visible inboard of the wing rear spar fitting lug: Before next flight, replace 
the cardan pin assembly (in accordance with Ref.5). Report to Airbus within 30 days. 
 
For the Gap check: 
 
- If measured gap (X+Y) is ≥ 1.5 mm: Before next flight, replace the cardan pin assembly (in 
accordance with Ref.5). Report to Airbus within 30 days. 
- If measured gap (X+Y) is >0.6 mm but <1.5 mm: Before next flight, provide Airbus with the 
following information: 
o Completed proforma provided in Appendix 2 of this AOT 
o Photographs of cardan pin head/wing/bush interfaces and nut/bush/wing 
interfaces( if possible provide ‘macro level’ detail shots of nut and pin face)  
o Movement Traceability Sheet (MTS) for the affected cardan pin 
The aircraft can then continue operations for a 30 days grace period whilst Airbus review the 
information provided. Airbus will consult with the operator during this grace period to request 
specific actions in the event that the findings are judged to be abnormal.  
- If measured gap (X+Y) is ≤ 0.6 mm: report gap to Airbus within 30 days. No further action 
required. 
 
When a gap check is performed, the results (including nil findings) must be reported to Airbus using 
the proforma provided in Appendix 2 of this AOT. 
 
 
4.3 SPARES AND TOOLING 
 
In case of part’s replacement, please refer to Ref.2 for procurable part numbers. 
 
In addition, refer to the applicable MBD CMM as follows: 
- For Basic MLG: refer to Ref.3 
- For Growth MLG: refer to Ref.4 
 
Should spares be required, they will be available from MBD local distribution centres and allocated on a 
case by case basis. 
 
 
5. FURTHER INFORMATION 
 
It is anticipated that this AOT will be rendered mandatory by issuance of an EASA Airworthiness 
Directive (AD). 
 
 
6. AOT APPROVAL 
 
The technical content of this document is approved under the authority of DOA nr. EASA.21J.031.  
 
 
7. REPORTING

### Page 5

CUSTOMER SERVICES DIRECTORATE 
1 ROND POINT MAURICE BELLONTE 
31707 BLAGNAC CEDEX FRANCE 
TELEPHONE + 33 (0)5 61 93 33 33 
 
ALERT OPERATORS TRANSMISSION - AOT
AOT ref: A32L003-14 Page 5 of 5 Date: 10 Mar 2014 
© AIRBUS S.A.S. 2014. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT 
 
Questions about this AOT and inspection results with or without findings are to be sent to Airbus 
Customer Services engineering as soon as possible after the AOT application, to the attention of: 
 
Philippe KERANGUEVEN 
Customer Services – SEEL1 
Phone : +33 (0) 5 67 19 18 42 
Fax : +33 (0) 5 67 19 12 05 
Email: philippe.kerangueven@airbus.com 
  
 
Best Regards, 
 
 
 
 
Jean-Luc MOUYSSET 
VICE PRESIDENT ENGINEERING SUPPORT 
CUSTOMER SERVICES 
Philippe GOURDON  
VICE PRESIDENT A330/A340 PROGRAMME 
CUSTOMER SERVICES DIRECTORATE

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
