# Airbus All Operators Telex A330-55A3040

Copy: Revision 02 ("U.S. DOT/FAA - Service Bulletin (2)"), 7 pages: PDF https://openairdocs.org/files/sha256/6f/ab/6fab7d2ab1d1706319fe24d8ee244bbdc114fd78d037a891ce4375548f6e97e6; text https://openairdocs.org/service-documents/airbus/aot-a330-55a3040/file/6fab7d2ab1d1.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2010-1309; AD 2011-08-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Other document (All Operators Telex)
- Number: A330-55A3040
- Latest revision known: A330-55A3040, Revision 02, dated September 30, 2009 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus/aot-a330-55a3040

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2011-08-12](https://openairdocs.org/ad/2011-08-12.md), effective May 26, 2011: Revisions 01 and 02

## Text (7 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2010-1309; AD 2011-08-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

ALL OPERATORS TELEX - ALL OPERATORS TELEX
SUBJECT: A330- ATA 55-40 - INSPECTION OF RUDDER SIDE SHELLS FOR
POTENTIAL SKIN TO HONEYCOMB DISBOND
OUR REF: AOT A330-55A3040 Rev 02 dated 30 September 09
OUR PREVIOUS REF: AOT A330-55A3040 Rev 01 dated 08 July 09
AOT A330-55A3040 Rev 00 dated 27 May 09
0. REASON FOR REVISION
This AOT has been revised to:
- Introduce an ultrasonic inspection in the reinforced areas of the
rudders. This ultrasonic inspection replaces the thermography
inspection as required by AOT A330-55A3040 Rev.01 and as defined in the
specific Technical Dispositions for reinforced areas location A. The
thermography inspection requirements remain applicable in non-
reinforced areas as defined in the specific Technical Dispositions for
location D.
- Introduce minor changes in Technical Disposition TD/K4/S3/27733/2009,
now revised at issue E:
- References to the specific Technical Dispositions for location
A have been updated
- References to the specific Technical Dispositions for the
"other areas" at location D have been included in appendix A.
- Airline/MSN cross-references have been updated where
necessary.
- Reflect that the ELCh inspection at Trailing Edge area has to be
repeated twice at intervals not exceeding 4500 FC, but no less than
4000 FC since last inspection.
No additional work is required for rudders that have been inspected
through AOT A330-55A3040 Rev.01 dated 08 July 09, except those on which
temporary option II or permanent vacuum loss hole restoration has been
performed according to the specific Technical Dispositions at Location
A: In this case, an additional Ultrasonic inspection within 21 months
from restoration date is required.
The revised paragraphs are indicated between **BEG.REV** and
**END.REV**.
1. AIRCRAFT AFFECTED
All A330 aircraft equipped with rudders having the Serial Numbers (SN)
1

### Page 2 (OCR)

listed in Technical Disposition ref. TD/K4/S3/27733/2009 issue E Table
1, and having accumulated 13000 FC or more since their first
installation on aircraft at receipt date of this AOT at original issue.
Note: Affected rudders listed in Technical Disposition ref.
TD/K4/S3/27733/2009 issue E Table 1, and having accumulated less than
13000 FC at receipt date of this AOT at original issue are also to be
inspected according to the AOT's instructions. However for these
rudders the accomplishment timescale given in paragraph 4.1.1 has to be
considered from the date when the 13000 FC threshold is reached.
In case a rudder originally fitted on one aircraft (refer to Aircraft
Inspection Report delivery document) has been removed and installed on
another aircraft, it is the responsibility of the operator to apply the
required instructions contained in this AOT to the new aircraft.
If the cross-reference Rudder SN/ Aircraft MSN given in
TD/K4/S3/27733/2009 issue E Table 1 does not reflect the current status
or if the identification plate is missing, contact Airbus.
2. REFERENCED DOCUMENTATION
**BEG.REV**
REF.1: OIT 999.0092/08: ATA55 - Rudder side shell skin disbonding
REF. 2: A330 SRM 55-41-13 Fig. 1 item 1/20, 5/25, 10/30, 15/35 depending
on mod status
REF.3: Technical Disposition ref. TD/K4/S3/27733/2009 issue E
REF.4. NTM TASK 51-10-26-220-801 (ELCh inspection)
REF 5: NTM TASK 51-10-28-220-801 (Vacuum Loss inspection)
REF 6: NTM TASK 55-40-02-290-801 (Thermography inspection)
REF 7: NTM TASK 51-10-19-280-801 (Tap test inspection)
REF 8: NTM TASK 51-10-24-270-801 NTM Temporary Revision TR 51-003
based on June 09 revision (Ultrasonic inspection)
**END.REV**
3. REASON
3.1 BACKGROUND
A deformation was visually detected on the rudder side shell of an A319
and an A321 in-service aircraft. Both rudders were sent to Airbus
facilities for further analysis. A review of production records
revealed that the deformations reported on both rudders corresponded to
areas that had been reworked in production.
The conclusion of the investigation is that the disbonding most likely
occurred as a consequence of excessive temperature applied, during a
2

### Page 3 (OCR)

hot curing rework of the inner skin in production. This rework occurred
outside autoclave.
Such hot curing reworks were also performed on some A330 rudders.
Operators were informed thru OIT REF.1 dispatched in November 2008 and
revised in March 2009.
3.2 AIM
For rudders that have been reworked in production with similar hot
curing process, this AOT calls for:
- a one-time Vacuum Loss inspection at rudder shell reinforced areas
- a three(3)-times repetitive Elasticity Laminate Checker (ELCh)
inspection at rudder shell trailing edge area
- a repetitive ELCh inspection in other rudder shell areas; until a
Vacuum Loss inspection is performed (considered as the terminating
4. SHORT TERM ACTION
4.1 PLANNING AND MANPOWER
This AOT is subject to an Airbus Monitored Retrofit Campaign. For
logistic purposes please provide in advance the inspection planning.
Your focal point for the planning and the logistics is:
Wera DIETZ, SEOT2,
Customer Services
Phone: +33 (0)5 67 19 14 22
Fax: +33 (0)5 61 93 27 45
Mailto: wera.dietz@airbus.com
4.1.1 ACCOMPLISHMENT TIMESCALE
Accomplishment timescale depends on the locations of the areas to be
inspected, which are fully described in Technical Disposition ref.
TD/K4/S3/27733/2009 issue E.
4.1.1.1 FOR REINFORCED AREAS
The one-time Vacuum Loss inspection described in paragraph 4.2.2.1 must
be performed within 1800 FH from the receipt date of this AOT at
original issue.
**BEG.REV**
4.1.1.2 FOR TRAILING EDGE AREA

### Page 4 (OCR)

The ELCh inspection described in paragraph 4.2.2.2 must be performed
within 21 months from the receipt date of this AOT at original issue,
and repeated twice at intervals not exceeding 4500 FC, but no less than
4000 FC since last inspection.
Following the third inspection without findings, no further action is
required in the trailing edge area.
**END.REV**
4.1.1.3 FOR OTHER AREAS (LOWER RIB/UPPER EDGE/LEADING
EDGE/OTHER
LOCATIONS)
The repetitive ELCh inspection described in paragraph 4.2.2.3.A. must
be performed:
- within 1800 FH from the receipt date of this AOT at original issue
- then, repeated at intervals not exceeding 1800 FH
- up to accomplishment of the terminating one-time Vacuum Loss
inspection mentioned in paragraph 4.2.2.3.B., that must be performed
within 21 months from the receipt date of this AOT at original issue.
Accomplishment of this terminating one-time inspection cancels the
repetitive ELCh inspection requirements described in paragraph
4.2.2.3.A.
If the vacuum loss inspection is performed within 1800 FH from the
receipt date of the AOT at original issue, no ELCh inspection is
required before or simultaneously.
4.1.2 MANPOWER
The manpower estimates given below are based on the direct labour to do
the work. These estimates assume that the work will be done by
experienced personnel. They might need to be revised upwards to suit
operators' circumstances.
These estimates do not include the manpower required for repairs in
case of findings.
A) Vacuum Loss inspection:
- Inspection: 1 man-hour per linear meter
- Hole restoration and resin curing time: 12 hours maximum elapsed time
B) ELCh inspection:
Note: Refer to Technical Disposition ref. TD/K4/S3/27733/2009 issue E
for identification of inspection area:
- Location B: 4 man-hours
- Location C: 4 man-hours
- Location D: 1 man-hour
- Location E: 0.5 man-hours
4.2 DESCRIPTION
4

### Page 5 (OCR)

4.2.1 JOB PREPARATION AND ACCESS
Refer to Technical Disposition ref. TD/K4/S3/27733/2009 issue E
paragraph "Job preparation".
4.2.2 INSPECTION INSTRUCTIONS
Rudder shells must be inspected only in areas mentioned in Technical
Disposition ref. TD/K4/S3/27733/2009 issue E Table 1.
Example: Rudder SN TS-2018 (end of table 1)
This rudder must be inspected on L/H side, at lower rib location only
as per Technical Disposition location D.
No inspection is required on R/H side shell.
4.2.2.1 FOR REINFORCED AREA
Perform a one-time Vacuum Loss inspection according to Technical
Disposition ref. TD/K4/S3/27733/2009 issue E location A.
Specific inspection instructions are to be requested by mail to:
Jean-Luc BOITEUX, SEESI
Customer Services
Phone: +33 (0)5 61 93 18 69
Fax: +33 (0)5 61 93 36 14
Mailto: jean-luc.j.boiteux@airbus.com
4.2.2.2 FOR TRAILING EDGE AREA
Perform three(3)-times repetitive ELCh inspection according to
Technical Disposition ref. TD/K4/S3/27733/2009 issue E locations B, B2,
C and E.
4.2.2.3 FOR OTHER AREAS (LOWER RIB/UPPER EDGE/LEADING
EDGE/OTHER
LOCATIONS)
A.) Perform a repetitive ELCh inspection according to Technical
Disposition ref. TD/K4/S3/27733/2009 issue E location D.
B.) Perform a one-time Vacuum Loss inspection according to specific
Technical Dispositions. In order to obtain these instructions, please
send a request to:
Jean-Luc BOITEUX, SEESI
Customer Services
Phone: +33 (0)5 61 93 18 69
Fax: +33 (0)5 61 93 36 14
Mailto: jean-luc.j.boiteux@airbus.com
5

### Page 6 (OCR)

They will be provided in a time-frame compatible with the inspection
planning (refer to paragraph 4.1).
4.2.3 JOB CLOSE UP
Refer to Technical Disposition TD ref. TD/K4/S3/27733/2009 issue E
paragraph "Job close up)".
4.2.4 ACTIONS IN CASE OF FINDINGS
In case of findings, document accurately the relevant inspection report
sheet, and contact Airbus at the following address before next flight
to get further instructions:
SEER 1/SEER2/SEER3
Customer Services
Fax: +33 (0)5 61 93 28 73
Mailto:
region1.StructureRepairSupport@airbus.com
region2.StructureRepairSupport@airbus.com
region3.StructureRepairSupport@airbus.com
Or for AOG request
AIRTAC (Airbus Technical AOG Center)
Customer Services
Phone: +33 (0)5 61 93 34 00
Fax: +33 (0)5 61 93 35 00
Mailto: airtac@airbus.com
4.2.5 REPORTING
If there are no findings, report to Airbus within 10 days from the
inspection date of each affected rudder, at the following address:
Jean-Luc BOITEUX, SEESI
Customer Services
Phone: +33 (0)5 61 93 18 69
Fax: +33 (0)5 61 93 36 14
Mailto: jean-luc.j.boiteux@airbus.com
**BEG.REV**
4.2.6 MATERIAL, TOOLING
- Adjustable access platform or Cherry Picker
- Inspection equipment for ELCh as per REF.4
- Inspection equipment for Vacuum Loss inspection as per REF.5
- Inspection equipment for Thermography as per REF. 6
6

### Page 7 (OCR)

- Inspection equipment for Tap test as per REF. 7
- Inspection equipment for Ultrasonic inspection as per REF. 8
**END.REV**
Note 1: In order for Airbus to provide adequate support to all affected
operators, it is recommended to place a Purchase Order for ELCh tool
two weeks ahead of the first scheduled inspection.
Note 2: A CD-Rom including ELCh familiarization has been shipped to all
affected operators via Airbus Field Service stations.
**BEG.REV**
Note 3: Instructions for restoration of Vacuum Loss inspection holes
are detailed in the specific Technical Dispositions, and can be
performed in 2 steps:
-Temporary restoration (option I): Hole closing with self-
adhesive patches, valid for 21 months. Correct cover application has to
be ensured by frequent detailed visual inspections at an interval not
exceeding 900 FH, until permanent restoration is performed, or
-Temporary restoration (option II): Hole filling with resin.
Local ultrasonic inspection in reinforced areas and local thermography
inspection in other areas must be performed before resin injection.
Final restoration has to be performed no later than 21 months after
temporary restoration.
-Permanent restoration: Hole filling with resin and restoration of
surface protection. Local ultrasonic inspection in reinforced areas and
local thermography inspection in other areas must be performed before
resin injection.
**END. REV**
Note 4: For thermography inspection, as a limited number of equipment
is available for loan from Airbus, necessary Infrared camera could also
be purchased at the following address:
FLIR SYSTEMS
Internet address: <http://www.flir.com/>
5. AOT APPROVAL
The technical content of this AOT has been approved under the authority
of EASA Design Organization Approval number EASA 21J.031.
It is anticipated that this AOT will be rendered mandatory.
6. REPORTING/ACKNOWLEDGMENT
7

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
