# Airbus All Operators Transmission A52N-014-22

Copy: Revision 1 ("AOT A52N-014-22 R01"), 40 pages: PDF https://openairdocs.org/files/sha256/e2/3f/e23fbb85e2924df994e58b5f52a59536f3d2bada7d3503bac4faa6584bed00b5; text https://openairdocs.org/service-documents/airbus/aot-a52n-014-22/file/e23fbb85e292.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2022-1300, the docket of AD 2023-02-11. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Other document (All Operators Transmission)
- Number: A52N-014-22
- Latest revision known: A52N-014-22, Revision 1, dated April 19, 2022 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus/aot-a52n-014-22

## Text (40 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2022-1300, the docket of AD 2023-02-11. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

CUSTOMER SERVICES DIRECTORATE
2 ROND POINT EMILE DEWOITINE
31700 BLAGNAC FRANCE
TELEPHONE + 33 (0)5 61 93 33 33
ALERT OPERATORS TRANSMISSION - AOT
AOT ref: A52N014-22 Rev 01 Page 1 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
SUBJECT: ATA 52 – A321NEO ACF overwing emergency exit slide release cable disconnected
AIRCRAFT TYPE:  A321-200NX
OUR REF.: A52N014-22 Rev 01 dated 19-APR-2022
OUR PREVIOUS REF.: A52N014-22 Rev 00 dated 21-MAR-2022
EFFECTIVITY DATE: 31-Mar-2022
0. REASON FOR REVISION:
AOT A52N014-22 Rev 00 was originally issued to recommend a one-time inspection of the A321NEO 
ACF overwing emergency exit slide release mechanism installation.
AOT A52N014-22 Rev 01: Airbus has detected that 9 A/C are not equipped with an Additional Center 
Tank (ACT) from production but they have instead been delivered with the provision for a possible future 
installation as per Mod 161927. As part of the ACT provision definition, Mod 161974 is automatically 
embodied for relocation of the emergency exit slide inflation reservoirs from the AFT (afterward) cargo 
compartment area into the cabin.
These 9 A/C were therefore listed in the Configuration 001 (inflation reservoir in the AFT cargo area) in 
the AOT A52N014-22 Rev 00 whereas they should have been listed in the Configuration 002 (inflation 
reservoir in the cabin).
The list of MSNs in both configurations and the description of both configurations have therefore been 
updated in the revision 01 of subject AOT.
The revised paragraphs are indicated between **BEG. REV** and **END REV**.
1. AIRCRAFT AFFECTED
A321NEO ACF (Airbus Cabin Flex) with the following MSNs:
08155, 08257, 08314, 08369, 08386, 08421, 08454, 08469, 08496, 08508, 08517, 08526, 08542, 08557, 
08567, 08573, 08587, 08593, 08608, 08617, 08629, 08637, 08647, 08655, 08666, 08701, 08710, 08712, 
08714, 08718, 08727, 08732, 08735, 08740, 08750, 08755, 08758, 08761, 08768, 08773, 08780, 08783, 
08794, 08796, 08799, 08800, 08804, 08813, 08814, 08816, 08823, 08830, 08834, 08837, 08839, 08861, 
08866, 08876, 08878, 08882, 08887, 08893, 08897, 08898, 08906, 08908, 08909, 08910, 08919, 08921, 
08923, 08930, 08936, 08941, 08946, 08952, 08955, 08957, 08958, 08965, 08966, 08968, 08971, 08979, 
08980, 08984, 08989, 08992, 08993, 08997, 09000, 09008, 09011, 09016, 09042, 09044, 09046, 09048, 
09054, 09055, 09059, 09063, 09073, 09076, 09080, 09082, 09083, 09087, 09090, 09092, 09095, 09106, 
09109, 09112, 09120, 09121, 09123, 09131, 09134, 09138, 09139, 09145, 09147, 09150, 09151, 09156, 
09157, 09162, 09164, 09168, 09178, 09187, 09191, 09195, 09196, 09198, 09204, 09208, 09209, 09210, 
09214, 09217, 09224, 09226, 09227, 09228, 09230, 09234, 09236, 09240, 09243, 09245, 09248, 09254, 
09255, 09258, 09263, 09265, 09266, 09267, 09278, 09281, 09284, 09285, 09288, 09289, 09293, 09297, 
09298, 09299, 09301, 09302, 09308, 09310, 09311, 09314, 09315, 09318, 09325, 09326, 09333, 09336, 
09347, 09349, 09359, 09364, 09365, 09366, 09368, 09374, 09376, 09377, 09383, 09386, 09396, 09398, 
09399, 09401, 09408, 09415, 09417, 09419, 09422, 09427, 09429, 09432, 09433, 09436, 09441, 09443, 
09444, 09445, 09452, 09458, 09462, 09466, 09468, 09472, 09477, 09478, 09487, 09492, 09495, 09496, 
09499, 09503, 09509, 09512, 09513, 09515, 09524, 09537, 09539, 09541, 09550, 09553, 09556, 09560, 
09564, 09567, 09571, 09575, 09584, 10000, 10007, 10010, 10017, 10020, 10025, 10029, 10032, 10036, 
10042, 10050, 10054, 10056, 10059, 10068, 10071, 10074, 10077, 10084, 10091, 10095, 10099, 10101, 
10105, 10109, 10115, 10116, 10120, 10124, 10125, 10130, 10141, 10143, 10147, 10150, 10151, 10155, 
10157, 10159, 10162, 10168, 10169, 10171, 10173, 10174, 10176, 10181, 10184, 10189, 10190, 10191, 
10193, 10195, 10198, 10199, 10205, 10206, 10210, 10211, 10213, 10214, 10217, 10218, 10221, 10222,

### Page 2

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 2 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
10224, 10227, 10228, 10229, 10235, 10238, 10240, 10244, 10245, 10254, 10256, 10257, 10259, 10260, 
10264, 10266, 10267, 10270, 10273, 10276, 10280, 10282, 10283, 10287, 10289, 10291, 10294, 10295, 
10296, 10299, 10303, 10304, 10305, 10306, 10311, 10312, 10314, 10318, 10319, 10321, 10322, 10323, 
10329, 10333, 10336, 10340, 10341, 10343, 10345, 10346, 10347, 10351, 10354, 10357, 10358, 10364, 
10367, 10369, 10370, 10371, 10375, 10377, 10381, 10382, 10385, 10387, 10389, 10391, 10393, 10395, 
10396, 10401, 10403, 10405, 10406, 10408, 10412, 10416, 10417, 10418, 10421, 10422, 10424, 10427, 
10428, 10438, 10440, 10445, 10446, 10456, 10457, 10460, 10466, 10472, 10474, 10476, 10479, 10480, 
10483, 10484, 10490, 10494, 10496, 10497, 10499, 10501, 10509, 10511, 10513, 10515, 10519, 10521, 
10522, 10523, 10526, 10532, 10540, 10551, 10564, 10566, 10583, 10585, 10595, 10597, 10609, 10613, 
10619, 10623, 10626, 10628, 10641, 10643, 10649, 10651, 10654, 10659, 10684, 10688, 10699, 10709, 
10730, 10757, 10805, 10822
MSN by Configuration:
**BEG. REV**
Note: The 9 A/C that have been moved from Conf 001 to Conf 002 in the AOT Revision 01 are highlighted 
in bold blue.
CONF 001 – MSNs of the impacted aircraft (A/C) without Additional Center Tank (ACT) and without 
provision for ACT
8155, 8257, 8314, 8369, 8386, 8421, 8454, 8469, 8496, 8508, 8526, 8542, 8573, 8608, 8617, 8629, 8637, 
8712, 8718, 8727, 8732, 8735, 8740, 8761, 8783, 8794, 8799, 8804, 8813, 8814, 8816, 8839, 8878, 8882, 
8906, 8908, 8919, 8921, 8930, 8936, 8941, 8957, 8958, 8966, 8979, 8984, 8993, 8997, 9000, 9008, 9011, 
9044, 9046, 9059, 9076, 9082, 9087, 9090, 9092, 9095, 9109, 9123, 9138, 9139, 9147, 9150, 9157, 9162, 
9164, 9168, 9196, 9204, 9208, 9209, 9210, 9214, 9217, 9227, 9228, 9236, 9240, 9248, 9254, 9258, 9266, 
9267, 9281, 9284, 9285, 9288, 9298, 9299, 9301, 9310, 9314, 9325, 9326, 9333, 9336, 9347, 9349, 9365, 
9366, 9368, 9376, 9396, 9399, 9401, 9415, 9417, 9422, 9429, 9436, 9441, 9443, 9444, 9452, 9462, 9468, 
9472, 9478, 9487, 9495, 9496, 9503, 9509, 9512, 9515, 9524, 9553, 9556, 9564, 9567, 9571, 10000, 
10007, 10010, 10025, 10036, 10050, 10054, 10056, 10059, 10068, 10071, 10077, 10084, 10091, 10099, 
10105, 10109, 10115, 10116, 10124, 10125, 10130, 10143, 10147, 10151, 10155, 10168, 10171, 10173, 
10174, 10189, 10190, 10191, 10199, 10205, 10210, 10211, 10217, 10221, 10222, 10224, 10227, 10229, 
10240, 10244, 10257, 10259, 10260, 10266, 10267, 10270, 10273, 10276, 10280, 10283, 10289, 10295, 
10296, 10304, 10305, 10312, 10318, 10321, 10322, 10323, 10333, 10336, 10340, 10341, 10343, 10345, 
10346, 10347, 10351, 10354, 10357, 10364, 10367, 10369, 10370, 10371, 10375, 10381, 10382, 10389, 
10391, 10393, 10401, 10406, 10417, 10422, 10424, 10438, 10440, 10445, 10456, 10460, 10466, 10479, 
10480, 10484, 10490, 10496, 10497, 10501, 10509, 10515, 10522, 10523, 10526, 10532, 10551, 10583, 
10585, 10651, 10654, 10659, 10688, 10699, 10730, 10757, 10805, 10822
CONF 002 - MSNs of the impacted aircraft (A/C) with Additional Center Tank (ACT) and / or with 
provision for ACT
8517, 8557, 8567, 8587, 8593, 8647, 8655, 8666, 8701, 8710, 8714, 8750, 8755, 8758, 8768, 8773, 8780, 
8796, 8800, 8823, 8830, 8834, 8837, 8861, 8866, 8876, 8887, 8893, 8897, 8898, 8909, 8910, 8923, 8946, 
8952, 8955, 8965, 8968, 8971, 8980, 8989, 8992, 9016, 9042, 9048, 9054, 9055, 9063, 9073, 9080, 9083, 
9106, 9112, 9120, 9121, 9131, 9134, 9145, 9151, 9156, 9178, 9187, 9191, 9195, 9198, 9224, 9226, 9230, 
9234, 9243, 9245, 9255, 9263, 9265, 9278, 9289, 9293, 9297, 9302, 9308, 9311, 9315, 9318, 9359, 9364, 
9374, 9377, 9383, 9386, 9398, 9408, 9419, 9427, 9432, 9433, 9445, 9458, 9466, 9477, 9492, 9499, 9513, 
9537, 9539, 9541, 9550, 9560, 9575, 9584, 10017, 10020, 10029, 10032, 10042, 10074, 10095, 10101, 
10120, 10141, 10150, 10157, 10159, 10162, 10169, 10176, 10181, 10184, 10193, 10195, 10198, 10206, 
10213, 10214, 10218, 10228, 10235, 10238, 10245, 10254, 10256, 10264, 10282, 10287, 10291, 10294, 
10299, 10303, 10306, 10311, 10314, 10319, 10329, 10358, 10377, 10385, 10387, 10395, 10396, 10403, 
10405, 10408, 10412, 10416, 10418, 10421, 10427, 10428, 10446, 10457, 10472, 10474, 10476, 10483, 
10494, 10499, 10511, 10513, 10519, 10521, 10540, 10564, 10566, 10595, 10597, 10609, 10613, 10619, 
10623, 10626, 10628, 10641, 10643, 10649, 10684, 10709

### Page 3

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 3 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
**END REV**
2. REFERENCED DOCUMENTATION
2.1 APPENDIX
Appendix 1: Inspection flowchart for Inspection Method 1
Appendix 2: Inspection flowchart for Inspection Method 2
Appendix 3: Inspection reporting form
2.2 REFERENCES
Ref.[1] AMM TASK 25-62-43-400-003-A - Installation of the Emergency Escape-Slide Release-
Mechanism Assembly
Ref.[2] AMM TASK 25-62-43-400-001-A - Installation of the Flexible Control Assembly
Ref.[3] AMM TASK 25-62-00-481-001-A - Do the special precautions before you do work on the offwing 
escape-slide systems
Ref.[4] AMM TASK 25-23-48-000-001-A or 25-23-48-000-001-B - Removal of the Cove Light Panel
Ref.[5] AMM TASK 25-62-00-820-001-A - Adjustment Procedure to Install the Lock pin in the Regulator 
Valve Assembly of the Inflation Reservoir - Offwing Escape-Slide
Ref.[6] AMM TASK 20-11-11-911-001-A - Safetying with Lockwire
Ref.[7] AMM TASK 25-62-00-081-001-A - Special Precautions after You Do the Work on the Offwing 
/Emergency-Exit-Door Escape-Slide Systems
Ref.[8] AMM TASK 25-23-48-400-001-A or 25-23-48-400-001-B - Installation of the Cove Light Panel
Ref.[9] AMM TASK 25-24-41-000-001-A or 25-24-41-000-001-C - Removal of the Overhead Stowage 
Compartments (OHSC)
Ref.[10] AMM TASK 25-24-41-400-001-A or 25-24-41-400-001-B - Installation of the Overhead 
Stowage Compartments (OHSC)
Ref.[11] OIT 999.0018/16 – ATA 00 – PROCEDURE TO REPORT RESULTS OF INSPECTION 
SERVICE BULLETINS AND ALERT OPERATORS TRANSMISSIONS
Ref.[12] In-Service Information (ISI) 52.20.00011 - A321ACF overwing emergency exit slide release 
cable disconnected
3. REASON
3.1 FACTS
Airbus informs operators that during an emergency slide deployment test on an A321NEO ACF overwing 
emergency exit, the slide did not deploy. During troubleshooting, it was identified that the slide release 
cable junction was found disconnected inside the surrounding collets and knurled sleeve nut (mushroom 
head connector not inserted into the T-slot cable joint), refer to figure 3.
3.2 HISTORY/BACKGROUND
The A321NEO ACF are equipped with 2 slide release mechanisms for the overwing emergency exits, one 
for each side of the A/C. A cable connects the mechanical slide release mechanism which is located 
above the overwing emergency exits to a reservoir that triggers the inflation of the emergency slide.
The affected cable junction is located close to the reservoir which triggers the slide inflation.
**BEG. REV**

### Page 4

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 4 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
For A/C without ACT and without provision for ACT (CONF 001), the connection is located in the AFT 
(afterward) cargo compartment, refer to figure 1.
Fig.1 Location of the slide release mechanism junction for A/C not equipped with ACT and not equipped 
with provision for ACT
For A/C with ACT and / or with provision for ACT (CONF 002), the cable junction is located in the cabin, 
refer to figure 2.
Fig.2 Location of the slide release mechanism junction for A/C equipped with ACT and / or equipped 
with provision for ACT
**END REV**
The mushroom head connector must be inserted in the T-slot cable joint as shown in figure 3:

### Page 5

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 5 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Fig.3 Slide release cable junction illustration
NOTE: An incorrect connection of the cable junction is not visually detectable without removal of the 
knurled sleeve nut and collets.

### Page 6

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 6 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
3.3 ROOT CAUSE
The investigation identified that the slide release cable junction was incorrectly installed during production.
3.4 INVESTIGATION
Only A321NEO ACF A/C are impacted by this potential incorrect installation.
Following the in-service finding, a quality investigation was launched and all A/C in production have been 
inspected, leading to two additional findings.
The slide release cable junction must therefore be inspected to ensure the proper connection and re-
installed properly in case of finding.
Additionally, the lockwire securing the junction assembly was found missing twice on in-service doors and 
twice during the quality investigation on production A/C. 
The lock wire that secures the knurled sleeve nut must be inspected after or during the check of the cable 
junction and properly installed if found missing.
The correct condition of the sleeve nut wire locking and of the slide release cable connection are shown 
in figure 4.
Fig.4 Correct installation of the slide release cable junction
Airbus has put in place corrective actions to prevent reoccurrence: the instructions for installation of the 
slide release mechanism in production have been enhanced and testing performed at the end of the 
installation have been reinforced.
The AMM tasks for installation of the complete slide release mechanism Ref.[1] and for the installation of 
the flexible control assembly Ref.[2] have also been reviewed to make sure the instructions provided in 
these AMM tasks are clear and could not lead to an incorrect installation after an in-service maintenance.

### Page 7

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 7 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
3.5 CONSEQUENCES
In case of disconnected slide release cable, the slide will not be available in case of emergency 
evacuation. Neither the automatic release nor the manual release will function without a mechanical 
connection to the slide inflation valve and reservoir.
There is a risk of having both overwing emergency exit slides unavailable during an emergency 
evacuation. In such case, the cabin crew has to redirect the passengers to alternative emergency exits, 
increasing the time required to evacuate all the passengers from the A/C.
4. OBJECTIVES OF THIS AOT
This AOT recommends a one-time inspection the installation of the A321NEO ACF overwing emergency 
exit slide release mechanism.
5. MAINTENANCE PROCEDURE
NOTE: This AOT is classified mandatory or expected to be classified mandatory by an Airworthiness 
Directive (AD). If the instructions of this AOT are marked as Required for Compliance (RC), the 
operator must follow the instructions as indicated. These instructions are introduced by “in 
accordance with”.
NOTE: The instructions of this AOT include procedures given in other documents or in other sections 
of the AOT. If the instructions of this AOT are NOT marked as Required for Compliance (RC), the 
operator can use an alternative procedure accepted by his/her local authority. These instructions 
are introduced by “refer to”.
NOTE: When this AOT gives the access or close-up instructions with no return to service tests, the 
operator can adapt these instructions to add flexibility to the maintenance operations. The technical 
intent of this AOT must comply with the set parameters.
5.1 PLANNING – (RC)
Perform the inspection in accordance with paragraphs 5.4 to 5.6 within four (4) months from AOT 
effective date on both Left Hand Side (LHS) and Right Hand Side (RHS) of the A/C.
If an incorrect connection of the slide release cable is detected during the inspection or the test of the 
slide release cable junction, the connection must be restored before next flight.
If the test or the inspection of the slide release cable connection is successful but the lockwire of the 
sleeve nut is found missing, the lockwire must be installed within the defined compliance of subject AOT 
(four (4) months from AOT effective date).
NOTE: If an offwing emergency escape slide has been successfully deployed on one side (LHS or 
RHS) of the A/C since the A/C delivery, the slide release mechanism on this side of the A/C does not 
require an inspection of the slide release cable junction but the inspection of the lockwire is still required.
Example:
Slide deployment test successfully performed through opening of 1 or 2 LHS overwing emergency 
exit(s): no need to inspect the slide release cable junction on the LHS, but the condition of the lockwire 
must be inspected.

### Page 8

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 8 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5.2 MANPOWER
**BEG REV**
CONF 001 – A/C without ACT and without provision for ACT
2 alternative Inspection Methods are possible for A/C without ACT and without provision for ACT. It is 
possible to perform either Inspection Method 1 or Inspection Method 2 to comply with subject AOT 
requirements.
If Inspection Method 1 is chosen, 2 people are required to perform the AOT instructions (one close to the 
slide release mechanism between the doors, one close to the inflation reservoir). They must be able to 
communicate during the inspection (using walkie-talkie for example).
Estimated required man/hours for Inspection Method 1 per A/C:
- Access and close-up: 1 man/hour
- Inspection: 0.5 man/hour
- Correction of the incorrect installation (if needed): 0.25 man/hour per side of the A/C (to be multiplied by 
2 in case of findings on both sides of the A/C)
If Inspection Method 2 is chosen, 1 person is required to perform the inspection.
Estimated required man/hours for Inspection Method 2 per A/C:
- Access and close-up: 1 man/hour
- Inspection: 0.25 man/hour
- Correction of the incorrect installation (if needed): 0.25 man/hour per side of the A/C (to be multiplied by 
2 in case of findings on both sides of the A/C)
CONF 002 – A/C with ACT and / or with provision for ACT
2 alternative Inspection Methods are possible for A/C with ACT and / or equipped with provision for ACT. 
It is possible to perform either Inspection Method 1 or Inspection Method 2 to comply with subject AOT 
requirements.
If Inspection Method 1 is chosen, 2 people are required to perform the AOT instructions (one close to the 
slide release mechanism between the doors, one close to the inflation reservoir). They must be able to 
communicate during the inspection (using walkie-talkie for example).
Estimated required man/hours for Inspection Method 1 per A/C:
- Access and close-up: 1 man/hour
- Inspection: 0.5 man/hour
- Correction of the incorrect installation (if needed): 6 man/hours per side of the A/C (to be multiplied by 2 
in case of findings on both sides of the A/C)
If Inspection Method 2 is chosen, 2 people are required to perform the inspection.
Estimated required man/hours for Inspection Method 2 per A/C:
- Access and close-up: 13 man/hours
- Inspection: 0.5 man/hour
- Correction of the incorrect installation (if needed): 0.25 man/hour per side of the A/C (to be multiplied by 
2 in case of findings on both sides of the A/C)
**END REV**

### Page 9

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 9 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5.3 ACCESS
**BEG REV**
CONF 001 – A/C without ACT and without provision for ACT
**END REV**
NOTE: Both LHS and RHS slide release mechanisms of the A/C must be inspected.
NOTE: If an offwing emergency escape slide has been successfully deployed on one side (LHS or 
RHS) of the A/C since the A/C delivery, the slide release mechanism on this side of the A/C does not 
require an inspection of the slide release cable junction but the inspection of the lockwire is still required.
In such case, some of the following instructions for the access will not be required.
(1) Remove the handle flaps from all the activated overwing emergency exits and turn the slide 
release trigger to DISARMED position. 
NOTE: Some A321ACF have 1 pair of overwing emergency exits deactivated.
(2) Do the special precautions before you do work on the offwing escape-slide systems Ref.[3] in 
order to ensure that the lock pin assembly (3) from the pocket (1) is installed in the regulator valve 
assembly (4) of the inflation reservoir (2), refer to figure 5.

### Page 10

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 10 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Fig.5 Inflation reservoir in the AFT cargo area
WARNING:
MAKE SURE THAT THE LOCK PIN IS CORRECTLY INSTALLED IN THE REGULATOR VALVE 
ASSEMBLY OF THE INFLATION RESERVOIR. THIS SAFETIES ALL COMPONENTS OF THE 
INFLATION SYSTEM IN OPERATION AND PREVENTS ACCIDENTAL:
- DISCHARGE OF THE INFLATION RESERVOIR
- DEPLOYMENT OF THE ESCAPE SLIDE
WHICH CAN CAUSE INJURY AND/OR DAMAGE.
WARNING:
MAKE SURE THAT YOU TURN THE REGULATOR ASSEMBLY IN A CLOCKWISE DIRECTION OR IN 
THE DIRECTION OF THE BLACK MARK. WHEN YOU TURN THE REGULATOR ASSEMBLY IN THIS 
DIRECTION, THE VALVE CLOSES.
IF YOU DO NOT OBEY THIS INSTRUCTION, YOU WILL START AN UNWANTED DEPLOYMENT 
SEQUENCE.
THIS CAN CAUSE INJURY TO PERSONNEL AND DAMAGE TO EQUIPMENT.
CAUTION: 
ESCAPE-SLIDE INFLATION RESERVOIR MAY INFLATE IF LOCK PIN IS NOT INSTALLED.
CAUTION:

### Page 11

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 11 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
MAKE SURE TO AVOID ANY DAMAGE ON THE STRUCTURE, TO ANY SYSTEM OR TO THE 
INSULATION WHEN ACCESSING THE INFLATION RESERVOIR.
If an offwing emergency escape slide has been successfully deployed on one side (LHS or RHS) 
of the A/C since the A/C delivery, DO NOT perform step 3 for this side of the A/C, whatever the 
Inspection Method chosen to comply with the AOT inspection.
Otherwise:
If the Inspection Method 1 described in paragraph 5.6 is chosen to comply with the AOT 
inspection, perform step 3.
If the Inspection Method 2 described in paragraph 5.6 is chosen to comply with the AOT 
inspection, DO NOT perform step 3.
(3) Get access to the slide release mechanism highlighted in figure 6, between the overwing 
emergency exits, as follows:
(a) Remove the necessary cove light panels Ref.[4]
NOTE: Subject step (3) is only required if Inspection Method 1 is chosen to perform the inspection. If 
Inspection Method 2 is chosen, it is not required to remove the cove light panel.
Fig.6 Slide release mechanism area

### Page 12

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 12 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
**BEG REV**
CONF 002 – A/C with ACT and / or with provision for ACT
**END REV**
NOTE: Both LHS and RHS slide release mechanisms of the A/C must be inspected.
NOTE: If an offwing emergency escape slide has been successfully deployed on one side (LHS or 
RHS) of the A/C since the A/C delivery, the slide release mechanism on this side of the A/C does not 
require an inspection of the slide release cable junction but the inspection of the lockwire is still required.
In such case, some of the following instructions for the access will not be required.
(1) Remove the handle flaps from all the activated overwing emergency exits and turn the slide 
release trigger to DISARMED position. 
NOTE: Some A321ACF have 1 pair of overwing emergency exits deactivated.
(2) Get access to the applicable inflation reservoir(s) (4) as follows:
(a) Open the door(s) of the applicable Over Head Storage Compartment(s) (OHSC)
(b) Release the quick-release fasteners and remove the cover(s) from the applicable OHSC(s).
(3)  Secure the inflation reservoir (4) as follows (refer to figure 7):
WARNING:
MAKE SURE THAT THE LOCK PIN IS CORRECTLY INSTALLED IN THE REGULATOR VALVE 
ASSEMBLY OF THE INFLATION RESERVOIR. THIS SAFETIES ALL COMPONENTS OF THE 
INFLATION SYSTEM IN OPERATION AND PREVENTS ACCIDENTAL:
- DISCHARGE OF THE INFLATION RESERVOIR
- DEPLOYMENT OF THE ESCAPE SLIDE
WHICH CAN CAUSE INJURY AND/OR DAMAGE.
WARNING:
MAKE SURE THAT YOU TURN THE REGULATOR ASSEMBLY IN A CLOCKWISE DIRECTION OR IN 
THE DIRECTION OF THE BLACK MARK. WHEN YOU TURN THE REGULATOR ASSEMBLY IN THIS 
DIRECTION, THE VALVE CLOSES.
IF YOU DO NOT OBEY THIS INSTRUCTION, YOU WILL START AN UNWANTED DEPLOYMENT 
SEQUENCE.
THIS CAN CAUSE INJURY TO PERSONNEL AND DAMAGE TO EQUIPMENT.
(a) Remove the lock pin assembly (5) from the pocket (3).
(b) Install the lock pin assembly (5) in the regulator valve assembly (6).
CAUTION: 
ESCAPE-SLIDE INFLATION RESERVOIR MAY INFLATE IF LOCK PIN IS NOT INSTALLED.
(c) If you cannot install the lock pin assembly (5) in the regulator valve assembly (6), do the 
adjustment procedure to install the lock pin assembly (5) Ref.[5].

### Page 13

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 13 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Fig.7 Installation of the inflation reservoir lock pin
If an offwing emergency escape slide has been successfully deployed on one side (LHS or RHS) 
of the A/C since the A/C delivery and if the Inspection Method 1 described in paragraph 5.6 is 
chosen to comply with the AOT inspection, DO NOT perform steps 4 and 5 on this side of the A/C.
Otherwise:
If the Inspection Method 1 described in paragraph 5.6 is chosen to comply with the AOT 
inspection, perform step 4 and DO NOT perform step 5.
If the Inspection Method 2 described in paragraph 5.6 is chosen to comply with the AOT 
inspection, DO NOT perform step 4 and perform step 5.
(4) Get access to the slide release mechanism highlighted in figure 8, between the overwing exits, 
as follows:
(a) Remove the necessary cove light panels Ref.[4]
NOTE: Subject step (4) is only required if Inspection Method 1 is chosen to perform the inspection.
Fig.8 Slide release mechanism area

### Page 14

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 14 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
(5) Get access to the slide release cable junction highlighted in figure 9, close to the inflation reservoir 
as follows:
(a) Remove the necessary OHSC Ref.[9] 
NOTE: Subject step (5) is only required if Inspection Method 2 is chosen to perform the inspection. 
WARNING:
BE CAREFUL WHEN YOU REMOVE OR INSTALL THIS EQUIPMENT. THIS EQUIPMENT IS HEAVY 
(MORE THAN 12 KG (26.5 lb)) AND CAN CAUSE INJURY AND/OR DAMAGE.
WARNING:
BEFORE YOU REMOVE OR INSTALL THE OHSC, MAKE SURE THAT ALL THE ELECTRICAL 
CONNECTORS ARE DISCONNECTED FROM THE OHSC. IF AN ELECTRICAL CONNECTOR IS 
CONNECTED, THERE IS A RISK OF ELECTRIC SHOCK TO THE PERSONNEL.
CAUTION:
WHEN YOU REMOVE/INSTALL THE OHSC, BE CAREFUL NOT TO CAUSE DAMAGE TO THE 
ELECTRICAL COMPONENT(S).
Fig.9 Slide release mechanism cable junction

### Page 15

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 15 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5.4 INSPECTION REQUIREMENTS – (RC)
A manual pull-test of the slide release mechanism cable or a direct visual inspection of the slide release 
mechanism cable junction in accordance with the instructions given in paragraph 5.6 is required.
A Detailed Visual Inspection (DVI) of the slide release mechanism cable lockwire is required either through 
the linings or by a direct visual check after removal of the necessary panels / linings (refer to paragraph 
5.3 for the access).
5.5 FINDINGS – (RC)
The 2 different possible findings are shown in figure 10: Missing lockwire around the knurled sleeve nut 
and disconnected cable inside the sleeve nuts and collets (mushroom head connector not inserted in the 
T-slot cable joint).
NOTE: Both possible findings are unrelated and independent. It is for example possible to have a 
disconnected cable junction inside the sleeve nut with a lockwire properly installed.
Fig.10 Missing lockwire and incorrect installation of the cable junction inside the knurled sleeve nut

### Page 16

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 16 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5.6 INSTRUCTIONS – (RC)
**BEG REV**
CONF 001 – A/C without ACT and without provision for ACT
2 alternative Inspection Methods are possible for A/C without ACT and without provision for ACT. It is 
possible to perform either Inspection Method 1 or Inspection Method 2 to comply with subject AOT 
requirements.
**END REV**
NOTE: Both LHS and RHS slide release mechanisms of the A/C must be inspected.
NOTE: If an offwing emergency escape slide has been successfully deployed on one side (LHS or 
RHS) of the A/C since the A/C delivery, the slide release mechanism on this side of the A/C does not 
require an inspection of the slide release cable junction but the inspection of the lockwire is still required.
In such case, some of the following instructions will not be required as it means that the cable junction 
was properly connected and the box related to the slide release cable of the AOT reporting sheet 
Appendix 3 must be filled with a “No”.
INSPECTION METHOD 1: pull-check
WARNING:
MAKE SURE THAT THE LOCK PIN IS CORRECTLY INSTALLED IN THE REGULATOR VALVE 
ASSEMBLY OF THE INFLATION RESERVOIR. THIS SAFETIES ALL COMPONENTS OF THE 
INFLATION SYSTEM IN OPERATION AND PREVENTS ACCIDENTAL:
- DISCHARGE OF THE INFLATION RESERVOIR
- DEPLOYMENT OF THE ESCAPE SLIDE
WHICH CAN CAUSE INJURY AND/OR DAMAGE.
If an offwing emergency escape slide has been successfully deployed on one side (LHS or RHS) 
of the A/C since the A/C delivery, note the condition of the lockwire and go directly to step 6 for 
this side of the A/C. 
Otherwise, proceed with below instructions.
(1) In the inflation reservoir area, person 1 has to horizontally pull the cable located next to the 
reservoir until reaching the maximum play and has to keep applying a light force to maintain the cable in 
this condition, refer to figure 11. The cable will have a light bow shape.

### Page 17

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 17 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Fig.11 Light force applied on the cable
(2) In the slide release mechanism area between the emergency exits highlighted in figure 12, person 
2 has to push by hand the slide release mechanism against the spring force (compression of the spring, 
in the FWD direction of the A/C, about 10 to 12mm movement of the mechanism is expected), refer to 
figure 13.
Fig. 12: Slide release mechanism area

### Page 18

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 18 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Fig. 13: Test of the slide release mechanism
A resistance should be felt after a short movement of the mechanism (about 10 to 12mm) as the release 
cable should be in tension and should straighten up, and the lock pin inserted in the regulator valve of the 
inflation reservoir stops any further movement, refer to figure 14.
Fig. 14: Test of the slide release mechanism
(3) In the inflation reservoir area, due to the movement of the slide release mechanism, the cable 
should move from a light bow shape into a straight line. Person 1 should feel the tension in the cable 
(during the application of pull force by person 2).

### Page 19

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 19 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
An immediate reaction of the cable during the movement of the slide release mechanism is the proof for 
a correct connection of the cable.
(4) Person 2 has to pull back the slide release mechanism to its original position
If the cable was found loose, go to step 5 in order to correct it.
If the behavior of the cable is correct, go directly to step 6.
(5) Re-connect the cable junction as follows (refer to figure 15):
(a) Check if the lockwire of the knurled sleeve is present or not (information required in the AOT 
inspection reporting form Appendix 3).
(b) Remove and discard the lockwire from the knurled sleeve nut (13) (if present).
WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH 
TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN 
CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
(c) Carefully loosen the knurled sleeve nut (13) and remove the collets from the cable junction.
Fig. 15: slide release cable connection
(d) Re-connect the flexible control assembly (1) to the release cable assembly (14) by inserting 
the mushroom head connector inside the T-slot cable joint. Install the two collets and tighten the knurled 
sleeve nut (13).
NOTE: When you install the collets, the slots in the collets must point to you. This lets you do a visual 
check that the inner cable stays connected while you tighten the knurled sleeve nut (13).
NOTE: The re-connection should be easy to perform. If not (cable not loose enough), don’t force and 
proceed with below instructions.
(e) Once the cable junction connected, there should be a light play when you lightly pull the cable 
with a finger, leading to a light bow shape, refer to figure 11.
If the re-connection of the flexible control assembly (1) to the release cable assembly (14) is easy 
and the behavior of the cable is satisfactory (light play in the cable), go directly to step (j).
Otherwise, adjust the length of the small cable connecting the cable junction to the reservoir as 
follows (refer to figures 16 and 17):
(f) Remove the lockwire (126) from the cable end.

### Page 20

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 20 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
(g) Loosen the cable as necessary and re-connect the cable junction as described in step (d).
(h) Adjust the cable length until having a tight condition of the cable (nearly no play), then unscrew 
back the cable end by 3 threads. Make sure that the threads of the cable end are visible along the complete 
diameter of the rod end hole highlighted in figure 17 to confirm that a minimum length of the thread is 
inside the rod end.
(i) Secure the small cable end with Wire-Locking Dia: 0.8 mm CRES Nickel Alloy - (Material Ref. 
14QFB1) Ref.[6].
WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH 
TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN 
CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
Fig. 16: slide release cable connection
Fig. 17: check of the thread minimal length inside the rod end
(j) Secure the knurled sleeve nut (13) with Wire-Locking Dia: 0.8 mm CRES Nickel Alloy - (Material 
Ref. 14QFB1) Ref.[6].
WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH 
TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN 
CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
(k) Go directly to step 7 (step 6 is not required)

### Page 21

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 21 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
(6) Visually inspect if the lockwire of the knurled sleeve nut is present. 
If the lockwire is missing, secure the knurled sleeve nut (13) with Wire-Locking Dia: 0.8 mm CRES Nickel 
Alloy - (Material Ref. 14QFB1) Ref.[6].
(7) Close Access
(a) Make sure that the work area is clean and clear of tools and other items.
(b) Perform the Special Precautions after You Do the Work on the Offwing/Emergency-Exit-Door 
Escape-Slide Systems Ref.[7].
CAUTION:
MAKE SURE THAT THE LOCK PIN IS REMOVED FROM THE REGULATOR VALVE ASSEMBLY OF 
THE INFLATION RESERVOIR. IF IT IS NOT REMOVED, IT CAN PREVENT THE INFLATION OF THE 
ESCAPE SLIDE/RAFT.
(c) Turn the slide release trigger to ARMED position and install the handle flaps on all the activated 
overwing emergency exits
NOTE: Some A321ACF have 1 pair of overwing emergency exits deactivated.
(d) Install the necessary cove light panels Ref.[8].
(8) Report the behavior of the slide release mechanism cable and what was the initial condition of 
the locking wire in the AOT inspection reporting form Appendix 3.

### Page 22

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 22 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
INSPECTION METHOD 2: Disassembly of the cable junction
WARNING:
MAKE SURE THAT THE LOCK PIN IS CORRECTLY INSTALLED IN THE REGULATOR VALVE 
ASSEMBLY OF THE INFLATION RESERVOIR. THIS SAFETIES ALL COMPONENTS OF THE 
INFLATION SYSTEM IN OPERATION AND PREVENTS ACCIDENTAL:
-DISCHARGE OF THE INFLATION RESERVOIR
-DEPLOYMENT OF THE ESCAPE SLIDE
WHICH CAN CAUSE INJURY AND/OR DAMAGE.
If an offwing emergency escape slide has been successfully deployed on one side (LHS or RHS) 
of the A/C since the A/C delivery, note the condition of the lockwire and go directly to step 5 if 
found missing, to step 6 is present for this side of the A/C. 
Otherwise, proceed with below instructions.
(1) In the inflation reservoir area, disassemble the slide release connection as follows (refer to figure 
18):
(a) Check if the lockwire of the knurled sleeve is present or not (information required in the AOT 
inspection reporting form Appendix 3).
(b) Remove and discard the lockwire from the knurled sleeve nut (13) (if present).
WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH 
TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN 
CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
(c) Carefully loosen the knurled sleeve nut (13) and remove the collets from the cable junction.
Fig. 18: slide release cable connection
(2) Visually inspect if the mushroom head connector of the release cable assembly (14) is properly 
fitted inside the T-slot cable joint of the flexible control assembly (1), as shown on figure 19.

### Page 23

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 23 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Fig.19 Correct installation of the slide release cable junction
If the cable connection is found incorrect, go to step 3 in order to correct it.
If the cable connection is satisfactory, go directly to step 4.
(3) Re-connect the cable junction as follows (refer to figure 18):
Connect the flexible control assembly (1) to the release cable assembly (14) by inserting the mushroom 
head connector inside the T-slot cable joint.
If the cable re-connection is easy to perform (cable assembly loose enough), go to step 4.
If you struggle to re-connect the cable junction, don’t force and go to step 5.
(4) Install the two collets and tighten the knurled sleeve nut (13).
NOTE: When you install the collets, the slots in the collets must point to you. This lets you do a visual 
check that the inner cable stays connected while you tighten the knurled sleeve nut (13).
(5) Once the cable junction connected, there should be a light play when you lightly pull the cable 
with a finger, leading to a light bow shape, refer to figure 20.

### Page 24

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 24 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Fig.20 Light force applied on the cable
If the re-connection of the flexible control assembly (1) to the release cable assembly (14) is easy 
and the behavior of the cable is satisfactory (light play in the cable), go directly to step 6.
Otherwise, adjust the length of the small cable connecting the cable junction to the reservoir as 
follows (refer to figures 21 and 22):
(a) Remove the lockwire (126) from the cable end.
(b) Loosen the cable as necessary and re-connect the cable junction as described in step 3 and 
step 4.
(c) Adjust the cable length until having a tight condition of the cable (nearly no play), then unscrew 
back the cable end by 3 threads. Make sure that the threads of the cable end are visible along the complete 
diameter of the rod end hole highlighted in figure 22 to confirm that a minimum length of the thread is 
inside the rod end.
(d) Secure the small cable end with Wire-Locking Dia: 0.8 mm CRES Nickel Alloy - (Material Ref. 
14QFB1) Ref.[6].
WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH 
TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN 
CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

### Page 25

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 25 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Fig. 21: slide release cable connection
Fig. 22: check of the thread minimal length inside the rod end
(6) Secure the knurled sleeve nut (13) with Wire-Locking Dia: 0.8 mm CRES Nickel Alloy - (Material 
Ref. 14QFB1) Ref.[6].
WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH 
TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN 
CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
(7) Close Access
(a) Make sure that the work area is clean and clear of tools and other items.
(b) Perform the Special Precautions after You Do the Work on the Offwing/Emergency-Exit-Door 
Escape-Slide Systems Ref.[7].
CAUTION:
MAKE SURE THAT THE LOCK PIN IS REMOVED FROM THE REGULATOR VALVE ASSEMBLY OF 
THE INFLATION RESERVOIR. IF IT IS NOT REMOVED, IT CAN PREVENT THE INFLATION OF THE 
ESCAPE SLIDE/RAFT.
(c) Turn the slide release trigger to ARMED position and install the handle flaps on all the activated 
overwing emergency exits
NOTE: Some A321ACF have 1 pair of overwing emergency exits deactivated.
(8) Report the condition of the slide release cable connection and what was the initial condition of the 
locking wire in the AOT inspection reporting form Appendix 3.

### Page 26

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 26 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
**BEG REV**
CONF 002 – A/C with ACT and / or with provision for ACT
2 alternative Inspection Methods are possible for A/C without ACT and / or with provision for ACT. It is 
possible to perform either Inspection Method 1 or Inspection Method 2 to comply with subject AOT 
requirements.
**END REV**
NOTE: Both LHS and RHS slide release mechanisms of the A/C must be inspected.
NOTE: If an offwing emergency escape slide has been successfully deployed on one side (LHS or 
RHS) of the A/C since the A/C delivery, the slide release mechanism on this side of the A/C does not 
require an inspection of the slide release cable junction but the inspection of the lockwire is still required.
In such case, some of the following instructions will not be required as it means that the cable junction 
was properly connected and the box related to the slide release cable of the AOT reporting sheet 
Appendix 3 must be filled with a “No”.
INSPECTION METHOD 1: pull-check
WARNING:
MAKE SURE THAT THE LOCK PIN IS CORRECTLY INSTALLED IN THE REGULATOR VALVE 
ASSEMBLY OF THE INFLATION RESERVOIR. THIS SAFETIES ALL COMPONENTS OF THE 
INFLATION SYSTEM IN OPERATION AND PREVENTS ACCIDENTAL:
- DISCHARGE OF THE INFLATION RESERVOIR
- DEPLOYMENT OF THE ESCAPE SLIDE
WHICH CAN CAUSE INJURY AND/OR DAMAGE.
If an offwing emergency escape slide has been successfully deployed on one side (LHS or RHS) 
of the A/C since the A/C delivery, note the condition of the lockwire and go directly to step 6 for 
this side of the A/C. 
Otherwise, proceed with below instructions.
(1) In the reservoir area, person 1 has to pull down the cable close to the reservoir until reaching the 
maximum vertical play and can keep applying a light force to maintain the cable in this condition. The 
cable will have a light bow shape, as illustrated in figure 23.
Fig.23 Light force applied on the cable

### Page 27

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 27 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
(2) In the slide release mechanism area between the emergency exits highlighted in figure 24, person 
2 has to push by hand the slide release mechanism against the spring force (compression of the spring, 
in the FWD direction of the A/C, about 10 to 12mm movement of the mechanism is expected), refer to 
figure 25.
Fig. 24: Slide release mechanism area
Fig. 25: Test of the slide release mechanism
A resistance should be felt after a short movement of the mechanism (about 10 to 12mm) as the release 
cable should be in tension and should straighten up, and the lock pin inserted in the regulator valve of the 
inflation reservoir stops any further movement, refer to figure 26.

### Page 28

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 28 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Fig. 26: Test of the slide release mechanism
(3) In the reservoir area, due to the movement of the slide release mechanism, the cable should 
move from a light bow shape into a straight line. Person 1 can either visually check the tension in the 
cable or by touching it (during the application of pull force by person 2).
An immediate reaction of the cable during the movement of the slide release mechanism is the proof for 
a correct connection of the cable.
(4) Person 2 has to pull back the slide release mechanism to its original position
If the cable is found loose, go to step 5 in order to correct it.
If the behavior of the cable is correct, go directly to step 6.
(5) Get access to the slide release cable junction close to the inflation reservoir and re-connect the 
cable junction as follows (refer to figure 27):
(a) Remove the necessary OHSC Ref.[9] 
WARNING:
BE CAREFUL WHEN YOU REMOVE OR INSTALL THIS EQUIPMENT. THIS EQUIPMENT IS HEAVY 
(MORE THAN 12 KG (26.5 lb)) AND CAN CAUSE INJURY AND/OR DAMAGE.
WARNING:
BEFORE YOU REMOVE OR INSTALL THE OHSC, MAKE SURE THAT ALL THE ELECTRICAL 
CONNECTORS ARE DISCONNECTED FROM THE OHSC. IF AN ELECTRICAL CONNECTOR IS 
CONNECTED, THERE IS A RISK OF ELECTRIC SHOCK TO THE PERSONNEL.
CAUTION:
WHEN YOU REMOVE/INSTALL THE OHSC, BE CAREFUL NOT TO CAUSE DAMAGE TO THE 
ELECTRICAL COMPONENT(S).
(b) Check if the lockwire of the knurled sleeve is present or not (information required in the AOT 
inspection reporting form Appendix 3).
(c) Remove and discard the lockwire from the knurled sleeve nut (13) (if present).
WARNING:

### Page 29

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 29 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH 
TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN 
CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
(d) Carefully loosen the knurled sleeve nut (13) and remove the collets from the cable junction.
Fig. 27: slide release cable connection
(e) Re-connect the flexible control assembly (1) to the release cable assembly (14) by inserting 
the mushroom head connector inside the T-slot cable joint. Install the two collets and tighten the knurled 
sleeve nut (13).
NOTE: When you install the collets, the slots in the collets must point to you. This lets you do a visual 
check that the inner cable stays connected while you tighten the knurled sleeve nut (13).
NOTE: The re-connection should be easy to perform. If not (cable not loose enough), don’t force and 
proceed with below instructions.
(f) Once the cable junction connected, there should be a light play when you lightly pull the cable 
with a finger, leading to a light bow shape, refer to figure 28.
Fig. 28: Play in the slide release cable
If the re-connection of the flexible control assembly (1) to the release cable assembly (14) is easy 
and the behavior of the cable is satisfactory (light play in the cable), go directly to step (k).
Otherwise, adjust the length of the small cable connecting the cable junction to the reservoir as 
follows (refer to figures 29 and 30):
(g) Remove the lockwire (126) from the cable end

### Page 30

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 30 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
(h) Loosen the cable as necessary and re-connect the cable junction as described in step (d)
(i) Adjust the cable length until having a tight condition of the cable (nearly no play), then unscrew 
back the cable end by 3 threads. Make sure that the threads of the cable end are visible along the complete 
diameter of the rod end hole highlighted in figure 30 to confirm that a minimum length of the thread is 
inside the rod end.
(j) Secure the small cable end with Wire-Locking Dia: 0.8 mm CRES Nickel Alloy - (Material Ref. 
14QFB1) Ref.[6].
WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH 
TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN 
CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
Fig. 29: slide release cable connection

### Page 31

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 31 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Fig. 30: check of the thread minimal length inside the rod end
(k) Secure the knurled sleeve nut (13) with Wire-Locking Dia: 0.8 mm CRES Nickel Alloy - 
(Material Ref. 14QFB1) Ref.[6].
WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH 
TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN 
CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
(l) Go directly to step 7 (step 6 is not required)
(6) Inspect if the lockwire of the knurled sleeve nut is present. 
Perform either a Detailed Visual Inspection (DVI) through the linings or a direct visual check of the knurled 
sleeve nut after removal of the necessary OHSC Ref.[9] in order to inspect the condition of the lockwire.
NOTE: To perform the visual inspection of the lockwire through the linings, Airbus recommends using a 
borescope or any device allowing to clearly see the condition of the lockwire, refer to figure 31.
Fig. 31: Check of the lockwire using a borescope
If the lockwire is missing, remove the necessary OHSC Ref.[9] (if not previously removed) in order to 
access the slide release cable connection and secure the knurled sleeve nut (13) with Wire-Locking Dia: 
0.8 mm CRES Nickel Alloy - (Material Ref. 14QFB1) Ref.[6].
WARNING:
BE CAREFUL WHEN YOU REMOVE OR INSTALL THIS EQUIPMENT. THIS EQUIPMENT IS HEAVY 
(MORE THAN 12 KG (26.5 lb)) AND CAN CAUSE INJURY AND/OR DAMAGE.
WARNING:

### Page 32

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 32 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
BEFORE YOU REMOVE OR INSTALL THE OHSC, MAKE SURE THAT ALL THE ELECTRICAL 
CONNECTORS ARE DISCONNECTED FROM THE OHSC. IF AN ELECTRICAL CONNECTOR IS 
CONNECTED, THERE IS A RISK OF ELECTRIC SHOCK TO THE PERSONNEL.
CAUTION:
WHEN YOU REMOVE/INSTALL THE OHSC, BE CAREFUL NOT TO CAUSE DAMAGE TO THE 
ELECTRICAL COMPONENT(S).
(7) Close Access
(a) Make sure that the work area is clean and clear of tools and other items.
(b) Turn the slide release trigger to ARMED position and install the handle flaps on all the 
activated overwing emergency exits
NOTE: Some A321ACF have 1 pair of overwing emergency exits deactivated.
(c) Install the necessary OHSC (if removed for inspection or re-connection of the cable junction) 
Ref.[10] and cove light panels Ref.[8].
WARNING:
BE CAREFUL WHEN YOU REMOVE OR INSTALL THIS EQUIPMENT. THIS EQUIPMENT IS HEAVY 
(MORE THAN 12 KG (26.5 lb)) AND CAN CAUSE INJURY AND/OR DAMAGE.
WARNING:
BEFORE YOU REMOVE OR INSTALL THE OHSC, MAKE SURE THAT ALL THE ELECTRICAL 
CONNECTORS ARE DISCONNECTED FROM THE OHSC. IF AN ELECTRICAL CONNECTOR IS 
CONNECTED, THERE IS A RISK OF ELECTRIC SHOCK TO THE PERSONNEL.
CAUTION:
WHEN YOU REMOVE/INSTALL THE OHSC, BE CAREFUL NOT TO CAUSE DAMAGE TO THE 
ELECTRICAL COMPONENT(S).
(d) Remove the lock pin from the regulator valve assembly of the inflation reservoir and store it in 
the dedicated pocket.
CAUTION:
MAKE SURE THAT THE LOCK PIN IS REMOVED FROM THE REGULATOR VALVE ASSEMBLY OF 
THE INFLATION RESERVOIR. IF IT IS NOT REMOVED, IT CAN PREVENT THE INFLATION OF THE 
ESCAPE SLIDE/RAFT.
(8) Report the behavior of the slide release mechanism cable and what was the initial condition of 
the locking wire in the AOT inspection reporting form Appendix 3.

### Page 33

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 33 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
INSPECTION METHOD 2: Disassembly of the cable junction
WARNING:
MAKE SURE THAT THE LOCK PIN IS CORRECTLY INSTALLED IN THE REGULATOR VALVE 
ASSEMBLY OF THE INFLATION RESERVOIR. THIS SAFETIES ALL COMPONENTS OF THE 
INFLATION SYSTEM IN OPERATION AND PREVENTS ACCIDENTAL:
-DISCHARGE OF THE INFLATION RESERVOIR
-DEPLOYMENT OF THE ESCAPE SLIDE
WHICH CAN CAUSE INJURY AND/OR DAMAGE.
If an offwing emergency escape slide has been successfully deployed on one side (LHS or RHS) 
of the A/C since the A/C delivery, note the condition of the lockwire and go directly to step 5 if 
found missing, to step 6 is present for this side of the A/C. 
Otherwise, proceed with below instructions.
(1) In the inflation reservoir area, disassemble the slide release connection as follows (refer to figure 
32):
(a) Check if the lockwire of the knurled sleeve is present or not (information required in the AOT 
inspection reporting form Appendix 3).
(b) Remove and discard the lockwire from the knurled sleeve nut (13) (if present).
WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH 
TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN 
CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
(c) Carefully loosen the knurled sleeve nut (13) and remove the collets from the cable junction.
Fig. 32: slide release cable connection
(2) Visually inspect if the mushroom head connector of the slide release cable assembly (14) is 
properly fitted inside the T-slot cable joint of the flexible control assembly (1), as shown on figure 33.

### Page 34

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 34 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Fig. 33 Correct installation of the slide release cable junction
If the cable connection is found incorrect, go to step 3 in order to correct it.
If the cable connection is satisfactory, go directly to step 4.
(3) Re-connect the cable connection as follows (refer to figure 32):
Connect the flexible control assembly (1) to the release cable assembly (14) by inserting the mushroom 
head connector inside the T-slot cable joint. 
(4) Install the two collets and tighten the knurled sleeve nut (13)
NOTE: When you install the collets, the slots in the collets must point to you. This lets you do a visual 
check that the inner cable stays connected while you tighten the knurled sleeve nut (13).
(5) Once the cable junction connected, there should be a light play when you lightly pull the cable with a 
finger, leading to a light bow shape, refer to figure 34.
Fig. 34: Play in the slide release cable
If the re-connection of the flexible control assembly (1) to the release cable assembly (14) is easy 
and the behavior of the cable is satisfactory (light play in the cable), go directly to step 6.
Otherwise, adjust the length of the small cable connecting the cable junction to the reservoir as 
follows (refer to figures 35 and 36):

### Page 35

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 35 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
(a) Remove the lockwire (126) from the cable end.
(b) Loosen the cable as necessary and re-connect the cable junction as described in step 3 and 
4.
(c) Adjust the cable length until having a tight condition of the cable (nearly no play), then unscrew 
back the cable end by 3 threads. Make sure that the threads of the cable end are visible along the complete 
diameter of the rod end hole highlighted in figure 36 to confirm that a minimum length of the thread is 
inside the rod end.
(d) Secure the small cable end with Wire-Locking Dia: 0.8 mm CRES Nickel Alloy - (Material Ref. 
14QFB1) Ref.[6].
WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH 
TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN 
CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
Fig. 35: slide release cable connection

### Page 36

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 36 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Fig. 36: check of the thread minimal length inside the rod end
(6) Secure the knurled sleeve nut (13) with Wire-Locking Dia: 0.8 mm CRES Nickel Alloy - (Material 
Ref. 14QFB1) Ref.[6].
WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH 
TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN 
CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
(7) Close Access
(a) Make sure that the work area is clean and clear of tools and other items.
(b) Install the necessary OHSC Ref.[10].
WARNING:
BE CAREFUL WHEN YOU REMOVE OR INSTALL THIS EQUIPMENT. THIS EQUIPMENT IS HEAVY 
(MORE THAN 12 KG (26.5 lb)) AND CAN CAUSE INJURY AND/OR DAMAGE.
WARNING:
BEFORE YOU REMOVE OR INSTALL THE OHSC, MAKE SURE THAT ALL THE ELECTRICAL 
CONNECTORS ARE DISCONNECTED FROM THE OHSC. IF AN ELECTRICAL CONNECTOR IS 
CONNECTED, THERE IS A RISK OF ELECTRIC SHOCK TO THE PERSONNEL.
CAUTION:
WHEN YOU REMOVE/INSTALL THE OHSC, BE CAREFUL NOT TO CAUSE DAMAGE TO THE 
ELECTRICAL COMPONENT(S).
(c) Perform the Special Precautions after You Do the Work on the Offwing/Emergency-Exit-Door 
Escape-Slide Systems Ref.[7].
CAUTION:
MAKE SURE THAT THE LOCK PIN IS REMOVED FROM THE REGULATOR VALVE ASSEMBLY OF 
THE INFLATION RESERVOIR. IF IT IS NOT REMOVED, IT CAN PREVENT THE INFLATION OF THE 
ESCAPE SLIDE/RAFT.
(d) Turn the slide release trigger to ARMED position and install the handle flaps on all the 
activated overwing emergency exits
NOTE: Some A321ACF have 1 pair of overwing emergency exits deactivated.
(8) Report the condition of the slide release cable connection and what was the initial condition of the 
locking wire in the AOT inspection reporting form Appendix 3.

### Page 37

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 37 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5.7 SPARES AND TOOLING
N/A
6. ADDITIONAL INFORMATION
6.1 FOLLOW-UP PLAN
ISI Ref.[12] provides up-to-date information on this subject.
6.2 IMPACTED DOCUMENTATION
D522-73301 & D522-73302
7. AOT APPROVAL
The technical content of this document is approved under the authority of the DOA ref.EASA.21J.031.
8. REPORTING
Address your inspection results (with or without findings) to Airbus Customer Services through the generic 
e-mail address. Refer to the latest reporting policy (OIT 999.0018/16 Ref.[11]). 
Give the AOT reference in the mail title, as follows: AOT A52N014-22 Inspection Result
You can address your questions about this AOT to Airbus Customer Services through TechRequest on 
Airbus World, selecting Maintenance & Engineering Domain, Engineering Support Section and ATA 52-
20.
Best Regards, 
Wolfgang WOHLERS
VICE PRESIDENT ENGINEERING SUPPORT
CUSTOMER SERVICES
Jean-Pierre GOMEZ
VICE PRESIDENT A320 FAMILY  
PROGRAMME
CUSTOMER SERVICES

### Page 38 (OCR)

AIRBUS
ALERT OPERATORS TRANSMISSION - AOT
APPENDIX 1 - Inspection flowchart for Inspection Method 1 (CONF 001 and CONF 002)
From the AOT effective date and within the threshold given in paragraph 5.1
[Inspection flowchart per side of the A/C, both sides to be inspected]
Has the emergency
slide ever been
deployed on affected
YES
overwing emergency
exits since A/C
delivery ?
Get access to the inflation reservoir,  Get access to the slide release mechanism and to
disarm the emergency exits and  the inflation reservoir, disarm the emergency exits
safety the inflation reservoir  and safety the inflation reservoir
Perform the test of the slide release cable
mechanism in accordance with paragraph 5.6
Is the slide
release cable
found loose?
Inspect the condition of the knurled
sleeve nut lockwire
(present or missing)
is the lockwire
of the knurled
sleeve nut
present ?  Reconnect the slide release cable
junction and install a lockwire on the
Get access to the slide release cable  knurled sleeve nut
junction and install a lockwire on the
knurled sleeve nut
Restore A/C condition and close access
Report inspection results to AIRBUS in accordance with ref. [11]
(as per Appendix 3, with indication of NIL finding)
AOT ref: A52N014-22 Rev 01  Page 38 of 40  Date: 19-APR-2022
C80_AOT_FM1104649_V8.0  © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT

### Page 39 (OCR)

AIRBUS
ALERT OPERATORS TRANSMISSION - AOT
APPENDIX 2 - Inspection flowchart for Inspection Method 2 (CONF 001 and CONF 002)
From the AOT effective date and within the threshold given in paragraph 5.1
[Inspection flowchart per side of the A/C, both sides to be inspected]
Has the emergency
slide ever been
deployed on affected
overwing emergency
exits since A/C
delivery ?
Get access to the inflation reservoir  Get access to the inflation reservoir and to the
and to the slide release cable junction,  slide release cable junction, disarm the emergency
disarm the emergency exits and  exits and safety the inflation reservoir
safety the inflation reservoir
Perform the inspection of the slide release cable
mechanism in accordance with paragraph 5.6
Inspect the condition of the knurled sleeve nut
lockwire (present or missing)
is the lockwire  Is the slide
of the knurled  release cable
sleeve nut  found
present ?  disconnected?
Reconnect the slide release cable
junction, re-install the collets and
Install a lockwire on the knurled  knurled sleeve nut and and install a
sleeve nut  lockwire on the knurled sleeve nut
Re-install the collets and knurled
sleeve nut and install a lockwire on
the knurled sleeve nut
Restore A/C condition and close access
Report inspection results to AIRBUS in accordance with ref. [11]
(as per Appendix 3, with indication of NIL finding)
AOT ref: A52N014-22 Rev 01  Page 39 of 40  Date: 19-APR-2022
C80_AOT_FM1104649_V8.0  © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT

### Page 40

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A52N014-22 Rev 01 Page 40 of 40 Date: 19-APR-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
APPENDIX 3 – Inspection reporting form
A/C INFORMATION:
OPERATOR:
A/C MSN:
A/C REGISTRATION:
DATE OF INSPECTION:
INSPECTION RESULTS:
Finding at LHS
(Yes / No)
Finding at RHS
(Yes / No)
Slide release cable 
disconnected?
Missing lockwire on the knurled 
sleeve nut?
COMMENTS (free text):

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
