# Airbus All Operators Transmission A55N003-20

Copy: No revision named ("AOT A55N003-20 Rev00"), 21 pages: PDF https://openairdocs.org/files/sha256/b9/f9/b9f9b3d8777af089a793260dd8883b7caa1da83249e0f88fc3c1c851ef762de4; text https://openairdocs.org/service-documents/airbus/aot-a55n003-20/file/b9f9b3d8777a.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2021-0015, the docket of AD 2021-03-05. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Other document (All Operators Transmission)
- Number: A55N003-20
- Page: https://openairdocs.org/service-documents/airbus/aot-a55n003-20

## Text (21 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2021-0015, the docket of AD 2021-03-05. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

CUSTOMER SERVICES DIRECTORATE
2 ROND POINT EMILE DEWOITINE
31700 BLAGNAC FRANCE
TELEPHONE + 33 (0)5 61 93 33 33
ALERT OPERATORS TRANSMISSION - AOT
AOT ref: A55N003-20 Rev 00 Page 1 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
SUBJECT: ATA 55 – INSPECTION OF RUDDER FOR DISBOND LINKED TO MODIFICATION 
SERVICE BULLETIN 55-1052 AND MODIFICATION SERVICE BULLETIN 55-1059
AIRCRAFT TYPE: A318,A319,A320,A321
OUR REF.: A55N003-20 Rev 00 dated 15-DEC-2020
EFFECTIVITY DATE: 
15th of December 2020 
1. AIRCRAFT AFFECTED
All A318 post Modification Service Bulletin (MSB) 55-1059 aircraft.
All A319, A320 and A321 post MSB 55-1052 aircraft.
Rudders installed with the two following conditions
- Serial Number (SN) from TS-2001 to TS-8463 or HMC-1002 to HMC-1241 
- MSB 55-1052 or MSB 55-1059 accomplished (PNs Post MOD in accordance with Appendix 1)
2. REFERENCED DOCUMENTATION
2.1 APPENDIX
Appendix 1: Rudder configuration PNs Post MSB 55-1052 or Post MSB 55-1059 
Appendix 2: Inspection Flowchart
Appendix 3: Inspection Report Form
2.2 REFERENCES
Ref [1] MSB 55-1052 Stabilizers – Rudder- Modify lightning strike protection front area
Ref [2] MSB 55-1059 - Rudder- Modify lightning strike protection front area
Ref [3] SBIT 20-0051, SBs A320-55-1052 REV02 / A320-55-1059 REV 00 - SB EMBODIMENT TO BE 
STOPPED
Ref [4] NTM 51-90-00 Visual Testing - General
Ref [5] NTM 51-10-19-280-801 Inspection of FRP Composite Components Honeycomb Sandwich Parts 
with the Woodpecker WP632
Ref [6] NTM 51-10-03 Inspection of CFRP and GFRP composite components – honeycomb sandwich 
parts - General
Ref [7] AMM 27-21-41-04 Rudder Removal – Installation
Ref [8] OIT 999.0018/16 Procedure to report results of inspections

### Page 2

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 2 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
3. REASON
3.1 FACTS
During accomplishment of the MSB 55-1052 Ref [1], an operator reported a local disbonding detected by 
tap test at the Left Hand (LH) side shell of the rudder close to the Lightning Protection Plate (LPP) 
(Figure1).
 
Ref [1] consists in the removal of the LPP at the forward monolithic part of the outer sandwich side shells 
LH & Right Hand (RH) side. The gap due to LPP removal is filled with glass layers cured. 
Inappropriate curing conditions may lead to a damage between the outer skin and the honeycomb core.
As part of the investigation further to the reported disbonding/debond, Airbus identified the need to 
further detail in Ref [1] and Ref [2] the glass layer curing instructions and the inspection after curing.
As the modification is applied on both sides, this can affect both LH and RH side shells.
Ref [1] applies to A319, A320 and A321 aircraft.
MSB 55-1059 Ref [2] describes same modification as Ref [1], applicable to A318 aircraft.
Figure 1 – Rudder General View, SB affected area (A318, A319, A320, A321)

### Page 3

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 3 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
3.2 CONSEQUENCES
Inappropriate curing conditions may lead to disbonding/debond which will impair the rudder structural 
integrity.
3.3 AIM
The aim of this AOT is to inspect both of the rudder side shells for potential disbonding/debond linked 
to accomplishment of the MSB Ref [1] or MSB Ref [2].
The area to be inspected, on LH side and RH side shells, is defined in Figure 2.

### Page 4 (OCR)

AIRBUS
ALERT OPERATORS TRANSMISSION - AOT
FWD
UP
SPAR
RIVET LINE
SPAR
RIVET LINE
FRP AREA  B=350
DIAMETER 150 mm  D=40
ETER 130 mm  VALID FOR ALL
(5.12 in)
BR7
Section D-D
(schematic)
C
SPAR
RIVET LINE
View A FI (Inspectionarea, Ex C)
Figure 2 - Inspection area (LH shell view)
(RH view symmetrical) (No scale)
AOT ref: A55N003-20 Rev 00  Page 4 of 21  Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT

### Page 5

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 5 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4. SHORT TERM ACTION
In order to address potential disbonding/debond linked to accomplishment of MSB Ref [1] or MSB 
Ref [2], Airbus has defined two short term actions:
- Issuance of SBIT 20-0051 Ref [3] to stop the accomplishment of the MSB Ref [1] and MSB Ref [2].
- Dispatch of this AOT to inspect rudders in post MSB Ref [1] or post MSB Ref [2] configuration.
NOTE: This AOT is classified mandatory or expected to be classified mandatory by an Airworthiness 
Directive (AD). The accomplishment instructions marked as Required for Compliance (RC) must be done 
to comply with the AD. “RC” is indicating these paragraphs accordingly 
NOTE: The accomplishment instructions of this AOT include procedures given in other documents or in 
other sections of the AOT. When the words ’refer to’ are used and the operator has a procedure accepted 
by the local authority he belongs to, the accepted alternative procedure can be used. When the words ’in 
accordance with’ are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this AOT do not 
constitute or affect the technical intent of the AOT. Operators can therefore, as deemed necessary, omit 
or add access and/or close-up steps to add flexibility to their maintenance operations as long as the 
technical intent of the AOT is met within the set parameters.
4.1 PLANNING AND MANPOWER
4.1.1 RC - ACCOMPLISHMENT TIMESCALE
For rudders in Post MSB Ref [1] or Post MSB Ref [2] configuration (Refer to Appendix 1 for applicable 
PNs) or when rudder configuration cannot be confirmed, inspect the area defined in figure 2, on LH and 
RH rudder side shells, in 2 (two) steps.
4.1.1.1 Step 01:
Perform a one-time General Visual Inspection (GVI) for bulging or waviness in accordance with 4.2.2 of 
this AOT. This must be accomplished within fifty (50) Flight Cycles (FC) from AOT issuance date or within 
three (3) months from AOT issuance date, whichever occurs first.
4.1.1.2 Step 02:
- In case of nil finding after GVI, perform a Special Detailed Inspection (SDI) for disbonding/debond 
in accordance with 4.2.3 within two hundred (200) FC from AOT issuance date or within three (3) 
months from AOT issuance date, whichever occurs first.
As an alternative to the SDI defined in 4.2.3 (for instance, in case of Non Destructive Tooling 
(NDT) unavailability), Airbus offers another SDI for disbonding/debond. This alternative must be 
accomplished in accordance with 4.2.4 within two hundred (200) FC from AOT issuance date or 
within three (3) months from AOT issuance date, whichever occurs first.
- In case of finding after GVI, perform a SDI for disbonding/debond in accordance with 4.2.3 before 
next flight. 
As an alternative to the SDI defined in 4.2.3 (for instance, in case of Non Destructive Tooling 
(NDT) unavailability), Airbus offers another SDI for disbonding/debond. This alternative must be 
accomplished in accordance with 4.2.4 within two hundred (200) FC from AOT issuance date or 
within three (3) months from AOT issuance date, whichever occurs first.

### Page 6

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 6 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4.1.2 MANPOWER
The estimated time to perform the inspection required in paragraph 4.2.2 is 0.5 man-hour per side shell. 
The inspection can be performed by one person.
The estimated time to perform the inspection required in paragraph 4.2.3 is 1.5 man-hours per side shell. 
The inspection can be performed by one person.
The estimated time to perform the inspection required in paragraph 4.2.4 is 6 man-hours per side shell. 
The inspection can be performed by one person.
4.2 DESCRIPTION
4.2.1 ACCESS
WARNING: 
PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A 
TASK ON OR NEAR: 
- THE FLIGHT CONTROLS 
- THE FLIGHT CONTROL SURFACES 
- THE LANDING GEAR AND THE RELATED DOORS 
-  COMPONENTS THAT MOVE. 
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN 
CAUSE DAMAGE TO THE EQUIPMENT.
WARNING: 
MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING NOTICES ARE 
IN POSITION. 
4.2.1.1 GVI access
The operator in charge of the GVI shall be located at the aircraft tail area, identified as position 6 in Figure3.
Figure 3 – Positions for GVI ground inspection

### Page 7

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 7 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4.2.1.2 SDI access
The use of a cherry picker or an adjustable access platform 12M (40 FT) is requested. It shall be located 
at the aircraft tail area, identified as position 6 in Figure 3, as close as possible to the upper rudder area 
for inspection, without being in contact with the aircraft.
4.2.2 RC - ONE-TIME GENERAL VISUAL INSPECTION
4.2.2.1 Refer to 4.2.1.1 for access.
4.2.2.2 From the ground, look upward to the rudder tip area, parallel to the rudder skin surfaces.
4.2.2.3 Perform the GVI on LH and RH rudder side shell at the rudder tip area (Figure 2), as per NTM 
51-90-00 Ref [4], for sign of surface bulging or skin waviness.
Ensure that light and reflection grant satisfactory results.
4.2.2.4 Perform SDI in accordance with accomplishment timescale in 4.1.1.2.

### Page 8

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 8 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4.2.3 RC - ONE-TIME SPECIAL DETAILED INSPECTION – WOODPECKER 
4.2.3.1 Refer to 4.2.1.2 for the access.
4.2.3.2 Perform the SDI on LH and RH rudder side shell in accordance with NTM 51-10-19-280-801 
Ref [5] in the area and following the scan path defined in Figure 4.
Figure 4 – Woodpecker inspection: calibration point and scan path orientation 
 
Note: The inspection scan path must be parallel to 
the spar rivet line.
Note: Calibration must be done in area free of defect 
and nearby the area to be inspected
4.2.3.3 In case of nil finding:
Send inspection report form (Appendix 3) to Airbus in accordance with OIT 999.0018/16 
Ref [8].
No further action from this AOT

### Page 9

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 9 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4.2.3.4 In case of finding:
The repair solution will depend on the damage sizes and location reported (see Figure 5):
Figure 5 – Damage definition and location on shell (No scale)

### Page 10

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 10 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
If W≤100mm (3.94in): 
If AREA<20000mm 2 (31 in2): 
- Before next flight perform temporary repair in accordance with 
TD/80860982/005/2020#B. 
-  Within five hundred (500) FC, perform the permanent repair. Contact Airbus 
for instructions. 
- Send inspection report form (Appendix 3) to Airbus in accordance with OIT 
999.0018/16 Ref [8].
- No further action from this AOT
or
- Before next flight perform permanent repair. Contact Airbus for instructions.
- Send inspection report form (Appendix 3) to Airbus in accordance with OIT 
999.0018/16 Ref [8].
- No further action from this AOT
If 20000mm 2 (31in2) ≤AREA≤ 30000mm2 (46.50 in2):
- Before next flight perform permanent repair. Contact Airbus instructions.
- Send inspection report form (Appendix 3) to Airbus in accordance with OIT 
999.0018/16 Ref [8].
- No further action from this AOT
If AREA>30000mm 2 (46.50in2):
-  Before next flight, replace the rudder in accordance with AMM 27-21-41-04 
Ref [7]. 
- Send inspection report form (Appendix 3) to Airbus in accordance with OIT 
999.0018/16 Ref [8].
- No further action from this AOT
If W>100mm (3.94in):
- Before next flight replace the rudder in accordance with Ref [7].
 - Send inspection report form (Appendix 3) to Airbus in accordance with OIT 
999.0018/16 Ref [8].
- No further action from this AOT
4.2.4 RC – REPETITIVE SPECIAL DETAILED INSPECTION – TAP TEST
4.2.4.1 Refer to 4.2.1.2 for the access.
4.2.4.2 Perform the SDI on LH and RH rudder side shell in accordance with NTM 51-10-03 Ref [6] 
in the area defined in Figure 2.
4.2.4.3 In case of nil finding:
After one thousand (1000) FC and before one thousand two hundred (1200) FC from previous 
SDI, perform a second SDI in accordance with Ref [6] of the rudder, LH and RH sides, to 
detect any sign of disbonding/debond.
If during the second inspection there is no sign of disbonding/debond:
- Send inspection report form (Appendix 3) to Airbus in accordance with OIT 999.0018/16 
Ref [8].
- No further action from this AOT

### Page 11

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 11 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4.2.4.4 In case of finding:
The permanent repair solution will depend on the damage sizes and location reported (see Figure 
5):
If W≤100mm (3.94in): 
If AREA<20000mm 2 (31 in2): 
- Before next flight perform temporary repair in accordance with 
TD/80860982/005/2020#B. 
-  Within five hundred (500) FC, perform the permanent repair. Contact Airbus 
for instructions. 
- Send inspection report form (Appendix 3) to Airbus in accordance with OIT 
999.0018/16 Ref [8].
- No further action from this AOT
or
- Before next flight perform permanent repair. Contact Airbus for instructions.
- Send inspection report form (Appendix 3) to Airbus in accordance with OIT 
999.0018/16 Ref [8].
- No further action from this AOT
If 20000mm 2 (31in2) ≤AREA≤ 30000mm2 (46.50 in2):
- Before next flight perform permanent repair. Contact Airbus instructions.
- Send inspection report form (Appendix 3) to Airbus in accordance with OIT 
999.0018/16 Ref [8].
- No further action from this AOT
If AREA>30000mm 2 (46.50in2):
-  Before next flight, replace the rudder in accordance with AMM 27-21-41-04 
Ref [7]. 
- Send inspection report form (Appendix 3) to Airbus in accordance with OIT 
999.0018/16 Ref [8].
- No further action from this AOT
If W>100mm (3.94in):
- Before next flight replace the rudder in accordance with Ref [7].
 - Send inspection report form (Appendix 3) to Airbus in accordance with OIT 
999.0018/16 Ref [8].
- No further action from this AOT
4.3 SPARES AND TOOLING
For woodpecker tooling sourcing refer to Ref [5].
For rudder replacement sourcing, proceed as follow:
• Send the inspection report form (Appendix 3) to Airbus Customer Services through TechRequest on 
Airbus World, selecting Engineering Domain, Engineering Support Section and ATA 55-41.
• Once Airbus Customer Services validate the rudder replacement, please contact your Single Point Of 
Contact (SPOC) through http://spares.airbus.com on AOG basis for free of charge rudder with Airbus 
validation approval.

### Page 12

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 12 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5. FURTHER INFORMATION
5.1 FOLLOW-UP PLAN
New revision dates of MSB Ref [1] and MSB Ref [2] will be provided through a revision of the Ref [3].
5.2 IMPACTED DOCUMENTATION
None.
6. AOT APPROVAL
The technical content of this document is approved under the authority of the DOA ref.EASA.21J.031.
7. REPORTING
Questions about this AOT are to be addressed to Airbus Customer Services through TechRequest on 
Airbus World, selecting Engineering Domain, Engineering Support Section and ATA 55-41.
As per latest reporting policy (Ref to OIT 999.0018/16 Ref [8]), inspection results as per Appendix 3 (with 
or without findings) are to be addressed to Airbus Customer Services through the generic e-mail address:  
inspection.results@airbus.com.
Best Regards,
Christian FREMONT
VICE PRESIDENT ENGINEERING SUPPORT
CUSTOMER SERVICES
Jean–Pierre GOMEZ
VICE PRESIDENT A320 FAMILY 
PROGRAMME
CUSTOMER SERVICES

### Page 13

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 13 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
APPENDIX 1 – Rudder configuration PNs Post MSB 55-1052 or Post MSB 55-1059
Rudder PN Post MSB 55-1052 or Post 
MSB 55-1059 A/C type
D554-71002-002-00 A319, A320, A321
D554-71002-004-00 A319, A320, A321
D554-71002-006-00 A319, A320, A321
D554-71004-002-00 A319, A320, A321
D554-71004-004-00 A319, A320, A321
D554-71004-006-00 A319, A320, A321
D554-71004-008-00 A319, A320, A321
D554-71004-010-00 A319, A320, A321
D554-71004-012-00 A319, A320, A321
D554-71004-014-00 A319, A320, A321
D554-71004-016-00 A319, A320, A321
D554-71006-100-00 A319, A320, A321
D554-71006-102-00 A319, A320, A321
D554-71006-104-00 A319, A320, A321
D554-71003-002-00 A318
D554-71003-004-00 A318
D554-71003-006-00 A318
D554-71003-008-00 A318
D554-71003-010-00 A318
D554-71003-012-00 A318
D554-71003-014-00 A318
D554-71005-006-00 A318
D554-71005-008-00 A318
Note: parts numbers of either formats (“-“ included or “-“ not included) are affected.

### Page 14

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 14 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
APPENDIX 2– Inspection Flowchart

### Page 15 (OCR)

AIRBUS
ALERT OPERATORS TRANSMISSION - AOT
Inspection for rudder disbonding/debond
SN: TS-2001 toTS8462 &
SN: HMC-1002 to HMC-1241
Within fifty (50) Flight Cycles from AOT issuance date  OR
Within three (3) months from AOT issuance date,
whichever occurs first
Check for rudder
configuration
Is it possible
to determine the rudder configuration
No  with regards to MSB 55-1052 and MSB 55-1059
either through the airline configuration management
records or by looking at the rudder
identification plate directly
on the aircraft ?
Yes
Is the rudder
either in POST MOD  No
SB 55-1052 or in
POST MOD SB 55-1059  No further action
configuration
(Appendix 2) ?
_ Yes
Perform a one time General Visual
Inspection in accordance with NTM 51-90-00
of the rudder, both sides, to detect any sign
of bulging or waviness
Any sign of  No  Within two hundred (200) Flight Cycles from AOT issuance date
bulging or waviness  Within three (3) months from AOT issuance date,
whichever occurs first
Yes
Before next flight
See Flowchart 2
Inspection flowchart 1/5
AOT ref: A55N003-20 Rev 00  Page 15 of 21  Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT

### Page 16

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 16 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
APPENDIX 2 – Inspection Flowchart (CONTINUATION)
Inspection flowchart 2/5

### Page 17 (OCR)

AIRBUS
ALERT OPERATORS TRANSMISSION - AOT
APPENDIX 2 - Inspection Flowchart (CONTINUATION)
Flowchart 3
Perform a Special Detailed Inspection in
accordance with NTM 51-10-19 of the
rudder, both sides, to detect any sign of
disbond or debonding
Any sign of
disbonding/
debond?
Yes
W < 100mm  No
(3.94in)
Yes
Area < 20000mm°  No  20000mm* (31 in?)≤Area s  Nop Area=30000mm (46.50in?)
(31in₴)  30000 mm* (46.50in*)
Yes
Before next flight perform
temporary repair law
TD/80860982/005/2020#B
Flight Cycles, perform the  permanent repair. Contact  Within five hundred (500)  Airbus for instructions  Before next flight, perform  the permanent repair.  Contact Airbus for  instructions  accordance with AMM 27-  Before next flight, perform  the rudder replacement in  for spare rudder sourcing  21-41-04. Contact Airbus
(Appendix 3).
Send inspection results
(Appendix 3) to Airbus in
accordance with OIT
999.0018/16
No further action
Inspection flowchart 3/5
AOT ref: A55N003-20 Rev 00  Page 17 of 21  Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT

### Page 18 (OCR)

AIRBUS
ALERT OPERATORS TRANSMISSION - AOT
APPENDIX 2 - Inspection Flowchart (CONTINUATION)
Flowchart 4
Perform a Special Detailed Inspection in
accordance with NTM 51-10-03 of the
rudder, both sides, to detect any sign of
disbond or debonding
No  Any sign of  disbonding/
debond?
Yes
No
W < 100mm
(3.94in)
Yes
20000mm₽  Area <  (31in₴)  No  20000mm- (31in?) ≤Area s  30000 mm- (46.50in*)  No  D Area >30000mm (46.50in2)
Yes
Yes
Before next flight perform
temporary repair iaw
TD/80860982/005/2020#B
Before next flight, perform
Within five hundred (500)  Before next flight, perform  the rudder replacement in
Flight Cycles, perform the  the permanent repair.  accordance with AMM 27-
permanent repair. Contact  Contact Airbus for  21-41-04. Contact Airbus
Airbus for instructions  instructions  for spare rudder sourcing
(Appendix 3).
Send inspection results  Send inspection results
(Appendix 3) to Airbus in  (Appendix 3) to Airbus in
accordance with OIT  accordance with OIT
999.0018/16  999.0018/16
See flowchart 5  No further action
Inspection flowchart 4/5
AOT ref: A55N003-20 Rev 00  Page 18 of 21  Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT

### Page 19 (OCR)

AIRBUS
ALERT OPERATORS TRANSMISSION - AOT
APPENDIX 2 - Inspection Flowchart (CONTINUATION)
Flowchart 5
After one thousand (1000) Flight Cycles and before
one thousand two hundred (1200) Flight Cycles from
previous inspection (refer to flowctart page 4),
perform a repetitive Special Detailed Inspection in
accordance with NTM 51-10-03 of the rudder, both
sides, to detect any sign of disbond or debonding
No  Any sign of
disbonding
debond?
Yes
W < 100mm  No
(3.94in)
Yes
Area <  No  20000mm? (31 in*)  No
20000mmг  SArea ≤  > Area >30000mm₴ (46.50in?)
(З1in₴)  30000 mm? (46.50in?)
Yes
Yes
Before next flight perform
temporary repair aw
TD/80860982/005/2020#B
Before next flight, contact
Within five hundred (500)  Airbus for spare rudder
Airbus for permanent repair  Flight Cycles, contact  D Airbus for permanent repair  Before next flight, contact  Rudder replacement in  sourcing (Appendix 3).
instructions  instructions  accordance with AMM 27-
21-41-04
Send inspection results
(Appendix 3) to Airbus in
accordance with OIT
999.0018/16
No further action
Inspection flowchart 5/5
AOT ref: A55N003-20 Rev 00  Page 19 of 21  Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT

### Page 20

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 20 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
APPENDIX 3 – Inspection Report Form (1/2)
A/C INFORMATION:
OPERATOR:
A/C MSN:
A/C REGISTRATION:
RUDDER PN: _ _ _ _ _ _ _ _ _ _ _ _ _ _ SN: _ _ _ _ _ _ _ _ _ _ 
RUDDER FLIGHT CYCLES:
RUDDER FLIGHT HOURS:
DATE OF INSPECTION:
GENERAL VISUAL INSPECTION RESULT:
Appendix 2 flowchart-1 LH SIDE RH SIDE
BULGING / WAVINESS IDENTIFIED? (Y/N)
WHEN APPLICABLE, SPECIAL DETAILED INSPECTION RESULT (NTM 51-10-19):
Appendix 2 flowchart-3 LH SIDE RH SIDE
DISBONDING / DEBOND IDENTIFIED? (Y/N)
 W DISBONDING/DEBOND <mm>
AREA DISBONDING/DEBOND (W x L <mm2>)
WHEN APPLICABLE, SPECIAL DETAILED INSPECTION RESULT (NTM 51-10-03):
Appendix 2 flowchart-4 LH SIDE RH SIDE
DISBONDING / DEBOND IDENTIFIED? (Y/N)
 W DISBONDING/DEBOND <mm>
AREA DISBONDING/DEBOND (W x L <mm2>)
WHEN APPLICABLE, SPECIAL DETAILED INSPECTION RESULT (NTM 51-10-03):
Appendix 2 flowchart-5 LH SIDE RH SIDE
DISBONDING / DEBOND IDENTIFIED? (Y/N)
 W DISBONDING/DEBOND <mm>
AREA DISBONDING/DEBOND (W x L <mm2>)

### Page 21

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A55N003-20 Rev 00 Page 21 of 21 Date: 15-DEC-2020
© AIRBUS S.A.S. 2020. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
APPENDIX 3 – Inspection Report Form (2/2)
COMMENTS (FREE TEXT):

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
