# Airbus Alert Operators Transmission A55W002-12

Copy: No revision named ("U.S. DOT/FAA - AOT A310-A55W002-12 with Appendix 1"), 5 pages: PDF https://openairdocs.org/files/sha256/8f/d2/8fd2794d6a5aec348f10fbc4932b694614a29d511e9a8e3d139bdd822d6949b3; text https://openairdocs.org/service-documents/airbus/aot-a55w002-12/file/8fd2794d6a5a.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2014-0123; AD 2015-07-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Other document (Alert Operators Transmission)
- Number: A55W002-12
- Page: https://openairdocs.org/service-documents/airbus/aot-a55w002-12

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2015-07-06](https://openairdocs.org/ad/2015-07-06.md), effective May 14, 2015: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus/aot-a55w002-12/proposed.md).

## Text (5 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2014-0123; AD 2015-07-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

ALERT OPERATORS TRANSMISSION - ALERT OPERATORS TRANSMISSION
SUBJECT: ATA 55 - RUDDER SIDE PANEL INSPECTION ALONG THE Z-PROFILE
OUR REF.: A55W002-12 dated 13 Dec 2012
1. AIRCRAFT AFFECTED
All A300-600 and A310 aircraft in pre modification 8827 configuration, with a rudder
assembly Part Number (PN) starting with A55471500.
The inspection has to be performed only if the last inspection as per ref.1 or 2 was
done off aircraft or if the rudder has been removed since then for any reason.
2. REFERENCED DOCUMENTATION
2.1 APPENDIX
Appendix 1: Inspection flow chart
2.2 REFERENCES
Ref.1: Service Bulletin SB A310-55-2044 dated Jul 23/07
Ref. 2: Service Bulletin SB A300-55-6043 dated Dec 03/07
Ref. 3: NTM 55-40-02 Part 4 (Ultrasonic inspection)
Ref.4. NTM 51-10-26 Part 7 (ELCH inspection)
Ref.5: NT 51-10-19 Part 5 (woodpecker inspection)
кет.6: NT S1-10-03 Part S (Ta test inspection)
Ref. 7: AMM 27-21-21 PB401  (Rudder removal/installation) dated prior to Dec 2012
Ref.8: NTM 55-40-09 Part 7, Figure 701 (Inspection Area)
3. REASON
3.1 FACTS
Affected rudders are subject to service Bulletins ref.1 and 2 introducing a specific
repetitive ultrasonic (UT) inspection along the rudder panel  front and bottom edge.
This inspection is intended to identify possible areas of disbonding on the internal
surface of the rudder side panels.
One A310 rudder with rudder assembly  . Part Number. (P/N) starting with A55471500 has
been recently identified with large inner skin disbond damage.
This rudder was inspected as per Service Bulletin ref.1 at 21028 accumulated Flighi
rudder was sent to Airbus facilities for a specific repair outside the trope of the  yCles (FC) with nil  986 Flight Cycles  (FC) after this inspection subject
inspection ref.1. The damage was detected during the incoming inspection.
An investigation revealed that the most probable cause of the large honeycomb core
debonding initiation was a blunt impact with no visible damage from outside during
rudder handling (removal/installation).
The rudder involved in this event was part number (PN) A55471500 series, which is
sensitive to damage in the  area of the Z-profile during rudder handling. An impact
damage might grow with difference of pressure associated to ground-air-ground
cycles.
3.2 CONSEQUENCES
Page 1

### Page 2 (OCR)

AOT_A55W002_12_00[1]. txt
An inner skin disbonding of the detected size degrades the structural integrity of
the rudder.  Tests performed in previous rudder showed a rapid propagation of damage
during artificial pressure cycling.
3.3 AIM
The aim of this AOT is to verify  the structural integrity of the rudder by means of
one time ultrasonic (UT) inspection.
The inspection must be repeated before next flight after any further re-installation
of the rudder onto an aircraft until issuance of revised AMM task ref.7. This
inspection will prevent undetected damage introduced during rudder ground handling.
4. SHORT TERM ACTION
4.1 PLANNING AND MANPOWER
4.1.1 ACCOMPLISHMENT TIMESCALE
The inspections described in paragraph 4.2 must be performed within 3 months trom
the reception date of this AOT.
4.1.2 MANPOWER
For A310 aircraft,  refer to SB ref.1 paragraph 1.G.
or A300-600 aircratt, refer to SB ret.2 paragraph 1.G
4.2 DESCRIPTION
4.2.1 ACCESS
Inspection must be performed with the rudder installed on the aircraft.
For A310 aircraft, refer to SB ret.1 paragraph 3.A. (1).
For A300-600 aircraft, refer to SB ref.2 paragraph 3.A. (1).
4.2.2 INSPECTION REQUIREMENTS
Refer to flowchart appendix 1 for an overview of the inspection requirements.
inspection its lie beats me fication start the
If installed rudder assembly  part number is not starting with A55471500, no further
action is required as per this AOT.
Rudder shells must be inspected in areas defined in:
- Figure 3 of SB ref.1,  for A310 aircraft.
- Figure 3 of SB ref. 2, for A300-600 aircraft.
Perform an ultrasonic (uT) inspection in accordance with ref.3 in the inspection
It case of finding, the ut indication shall be verified to differentiate disbonc
from other possible damages.  This differentiation should be done using both methods:
• ELCH in accordance with ref.4 for detection of external and internal disbond.
- woodpecker in accordance with ret.5 or Tap test in accordance with ref.6 for
detection of external disbond.
Page 2

### Page 3 (OCR)

AOT_A55W002_12_00[1]. txt
Note: In case of UT indication in booster area (see ref.8), report to Airbus to get
further instructions before next flight.
If finding is confirmed as disbond damage, refer to Para. 4.2.3.
If finding is confirmed as other type of damage (e.g. liquid ingress), check
pplicable SRM chapter for allowable damage.
The inspection must be repeated before next flight after any further re-installation
of the rudder onto an aircraft until issuance of revised AMM task ret.7.
4.2.3 FINDINGS
In case of disbond with width equal or less than 50 mm (1.968 in.)  and with length
- For A310 aircraft,  - for A310 a traft, refer to s ref. i paragraph 3.. (1)re next Tight.
- For A300-600 aircraft, refer to SB ref.2 paragraph 3.C.(1).
Then, contact Airbus within 10 days from the date of the inspection with a detailed
damage report to get permanent repair instructions. The permanent repair shall be
performed within 100FC from inspection date.
In case of disbond with width greater than 50 mm (1.968 in.) or with length greater
than 150 mm (5.905 in.), contact Airbus before next flight with a detailed damage
report to get further instructions.
Detailed damage report has to be sent to the following address:
Repair Engineering (SEER1/SEER2/SEER3)
Services
Fax: +33 (0) 5 61 93 28 73
regionl.StructureRepairSupport@airbus.com
region2.StructurerepairSupport@airbus.com
region3.StructureRepairSupport@airbus.com
Or for AOG request
AIRTAC (Airbus Technical AOG Center)
Customer Services
Phone: +33 (0) 5 61 93 34 00
Fax:  +33 (0)5 61 93 35 00
Mailto: airtac@airbus.com
4.3 SPARES AND TOOLING
- Inspection equipment for Ultrasonic inspection as per ref.3.
- Inspection equipment for ELCH as per ref.4.
- Inspection equipment for woodpecker test as per ref.5.
- Inspection equipment for Tap test as per ref.6.
5. FURTHER INFORMATION
5.1 FOLLOW-UP PLAN
The AMM task ref.7 will be revised to include this UT inspection after each
re-installation of the rudder onto an aircraft.
The revised AMM is expected to be issued on the second quarter of 2013.
Page 3

### Page 4 (OCR)

AOT_A55W002_12_00[1]. txt
5.2 IMPACTED DOCUMENTATION
AMM 27-21-21 PB 401
6. AOT APPROVAL
The technical content of this document is approved under the authority of DOA nr.
EASA. 21J. 031.
7. REPORTING/ACKNOWLEDGEMENT
operators are requested to acknowledge receipt of this AO within 48 hours after
receipt to:
Cecile BORDES SEES
E-mail: Cecile.bordes@airbus.com
Fax number: +33 (0) 5.61.93.36.14
Questions about this AOT and inspection results with or without findings are to be
to Airbus Customer Services  engineering as soon as possible, after the Аот
application, to the attention of:
Paloma LLEDIN BARBANCHO - SEES1
Customer Services
Phone: +33 (0)5 67 19 10 84
Fax: +33 (0)5 61 93 36 14
Mailto: paloma.lledin@airbus.com
Best Regards,
Jean-Luc MOUYSSET  Philippe BOUCHERAT
VICE PRESIDENT ENGINEERING SUPPORT  VICE PRESIDENT A300/A310
PROGRAMME
CUSTOMER SERVICES  CUSTOMER SERVICES
Page 4

### Page 5 (OCR)

Inspection Flowchart AOT ref.: A55W002-12
Rudder PN A55471500 series re-installed onto aircraft.
Within 3 months from AOT reception, perform UT inspection with rudder installed in aircraft as per as per NTM 55-40-02 Part 4 in
area defined in SB A310-55-2044 Fig. 3 or SB A300-55-6043 Fig.3
yes  Finding  no  further re-installation of the rudder onto an aircraft  Repeat the inspection before next flight after any
until issuance of revised AMM 27-21-21 PB401
Disbond confirmation requested using both methods:
- ELCH NTM 51-10-26 Part 7 for external and internal disbond.
- Woodpecker NTM 51-10-19 Part 5 or Tap test NTM 51-10-03 Part 5 for external disbond
yes  Finding confirmed as  disbond  no  Check applicable SRM chapter for allowable damage
Disbond size W≤50mm and L≤150mm  Core venting before next flight
Report to Airbus within 10 days to get permanent repair
instructions / permanent repair to be performed within 100FC
Disbond size W>50mm or L>150mm  Report to Airbus to get further instructions
before next flight
AIRBUS

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
