# Airbus All Operators Transmission A57N020-22

Copy: No revision named ("AOT A57N020-22"), 21 pages: PDF https://openairdocs.org/files/sha256/d6/9a/d69ab4b215b1ebadfa43c6d352c57d7e7d2e4427f736d36452aa02bb94120808; text https://openairdocs.org/service-documents/airbus/aot-a57n020-22/file/d69ab4b215b1.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2023-1815, the docket of AD 2023-23-04. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Other document (All Operators Transmission)
- Number: A57N020-22
- Page: https://openairdocs.org/service-documents/airbus/aot-a57n020-22

## Text (21 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2023-1815, the docket of AD 2023-23-04. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

CUSTOMER SERVICES DIRECTORATE
2 ROND POINT EMILE DEWOITINE
31700 BLAGNAC FRANCE
TELEPHONE + 33 (0)5 61 93 33 33
ALERT OPERATORS TRANSMISSION - AOT
AOT ref: A57N020-22 Rev 00 Page 1 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
SUBJECT: ATA 57 – Inspection of CWB rear lower spar and slanted beam areas
AIRCRAFT TYPE: A321
OUR REF.: A57N020-22 Rev 00 dated 07-DEC-2022
EFFECTIVITY DATE: 16-Dec-2022
1. AIRCRAFT AFFECTED
A321 CEO Aircraft (A/C)
A/C Models: A321-111, A321-112, A321-131, A321-211, A321-212, A321-213, A321-231, A321-232.
2. REFERENCED DOCUMENTATION
2.1 APPENDIX
Appendix 1: AOT instructions flowchart
Appendix 2: AOT embodiment reporting form
2.2 REFERENCES
Ref.[1] Aircraft Maintenance Manual (AMM) TASK 28-10-00-910-002-A – "Access to the Fuel Tanks and 
the Work Areas"
Ref.[2] Aircraft Maintenance Manual (AMM) TASK 33-42-11-000-001-A – "Removal of the Landing 
Light"
Ref.[3] Structural Repair Manual (SRM) 53-35-11-07-A - FAIRING DOORS, FR40-FR42
Ref.[4] Illustrated Parts Catalog (IPC) FIG. 29-22-83-07 - HYDRAULIC INSTL-BLUE SYSTEM Zone(s) 
190
Ref.[5] Structural Repair Manual (SRM) 51-42-11 - FASTENER INSTALLATION AND REMOVAL - 
METALLIC STRUCTURE
Ref.[6] Non-destructive Testing Manual (NTM) 51-10-08 - HFEC Inspection for Surface Breaking 
Cracks"
Ref.[7] Non-destructive Testing Manual (NTM) 51-10-01 – "Rotating Probe Testing – General"
Ref.[8] Structural Repair Manual (SRM) 51-44-11 - FASTENERS - HOLE AND DRILL DATA - 
METALLIC STRUCTURE
Ref.[9] Structural Repair Manual (SRM) 51-43 – FASTENER OVERSIZE AND ALTERNATIVE
Ref.[10] Structural Repair Manual (SRM) 51-23-11 – PAINT COATINGS
Ref.[11] Structural Repair Manual (SRM) 51-76-12 – REPAIR OF FUEL TANK SEALING
Ref.[12] Aircraft Maintenance Manual (AMM) TASK 33-42-11-400-003-A – "Installation of the Landing 
Light"
Ref.[13] Structural Repair Manual (SRM) 51-76-11 – REPAIR OF SEALING EXCLUDING FUEL TANK
Ref.[14] Technical Follow-Up (TFU) 57.11.00020 – "A321 - CWB rear lower spar junction area"
Ref.[15] OIT 999.0018/16 – ATA 00 – PROCEDURE TO REPORT RESULTS OF INSPECTION
SERVICE BULLETINS AND ALERT OPERATORS TRANSMISSIONS

### Page 2

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 2 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
3. REASON
3.1 FACTS
In the frame of A321 XLR certification, it has been highlighted high fatigue stress affecting 2 areas:
- the A321 CEO Center Wing Box (CWB) rear lower spar junction area at Fr42
- the A321 CEO FR42 slanted beam connection with rear spar and lower panel
Area A. CWB rear lower spar junction area at Fr42
Rear Spar CWB
Figure 1: CWB rear spar fitting component description (LH shown - RH symmetrical)

### Page 3

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 3 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Figure 2: Overview of lower corner fitting location inside and outside CWB 
(LH shown - RH symmetrical)
Figure 3: Lower corner fitting location inside CWB - Zoom view looking backward & forward
(LH shown - RH symmetrical)

### Page 4

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 4 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Area B. FR42 slanted beam connection area
Figure 4: Overview of Fr42 slanted beam junction location after CWB rear
Figure 5: Location of Fr42 slanted at connection with CWB rear spar and lower panel 
(LH shown - RH symmetrical)

### Page 5

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 5 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
3.2 HISTORY/BACKGROUND
In the frame of Fatigue and Damage Tolerance harmonization of the Single Aisle family, new stress 
calculation has been done in the CWB and slanted junction areas at FR42, leading to updated margins.
3.3 ROOT CAUSE
Stress analyses have highlighted high fatigue stress in the areas of the FR42 front fitting rear spar and 
slanted junction.
3.4 INVESTIGATION
Following margin update, investigation has revealed that cracks may appear:
- in the CWB area at FR 42
- at slanted junction area at FR42
3.5 CONSEQUENCES
In case of unrepaired crack(s), the CWB residual strength may be reduced. 
As a consequence, an inspection for potential findings on the two (2) following items is required:
Item 1. CWB rear lower spar junction area at Fr42
Cracks may appear on the Left (LH) and Right (RH) sides of the rear spar lower flange and/or on the LH 
and RH side of Frame 42 front fitting:
- 1a/ Rear spar lower flange (XY plan) 
Figure 6: Critical rear spar edge at FR42

### Page 6

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 6 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
- 1b/ Frame 42 front fitting at junction with rear spar (YZ plan)
Figure 7: Critical rear spar fastener hole at FR42 
Item 2. FR42 slanted beam connection area
Cracks may appear on the Left (LH) and Right (RH) side of FR42 slanted beam connection:
Figure 8: Critical fastener hole at slanted beam junction per A/C side

### Page 7

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 7 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4. OBJECTIVES OF THIS AOT
This AOT requests a one-time inspection of both below areas:
- the A321 CEO CWB rear lower spar junction area through rototest and High Frequency Eddy Current 
(HFEC)
- the A321 CEO FR42 slanted beam connection through rototest
5. MAINTENANCE PROCEDURE
NOTE: This AOT is classified mandatory or expected to be classified mandatory by an Airworthiness 
Directive (AD). If the instructions of this AOT are marked as Required for Compliance (RC), the 
operator must follow the instructions as indicated. These instructions are introduced by “in 
accordance with”.
NOTE: The instructions of this AOT include procedures given in other documents or in other sections 
of the AOT. If the instructions of this AOT are NOT marked as Required for Compliance (RC), the 
operator can use an alternative procedure accepted by his/her local authority. These instructions 
are introduced by “refer to”.
NOTE: When this AOT gives the access or close-up instructions with no return to service tests, the 
operator can adapt these instructions to add flexibility to the maintenance operations. The technical 
intent of this AOT must comply with the set parameters.
5.1 PLANNING (RC)
For A/C having accumulated less than 31000 Flight Cycles (FC), do the actions in accordance with 
paragraphs 5.4 to 5.7 before exceeding 31000FC from A/C Entry Into Service or no later than 6 months 
from the AOT effective date whichever occurs later.
For A/C having already exceeded 31000FC at the time of AOT effective date, a compliance time is 
granted to do the actions in accordance with paragraphs 5.4 to 5.7:
- 6 months or 2FC whichever occurs later from AOT effective date for A/C having cumulated between 
31000 & 49000FC
- 3 months or 2FC whichever occurs later from AOT effective date for A/C having accumulated more 
than 49000FC
Note: Inspection threshold and related compliance time are built based on A/C landing cases 
accumulation. Consequently, inspection values are driven by A/C FC, Flight Hours (FH) is not relevant.

### Page 8

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 8 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5.2 MANPOWER
WARNING:
TWO PERSONS ARE NECESSARY FOR THIS PROCEDURE:
- ONE PERSON IN THE TANK TO DO THE PROCEDURE, AND
- A SECOND PERSON OUT OF THE TANK TO MONITOR THE SAFETY CONDITIONS.
IF YOU DO NOT OBEY THIS PRECAUTION, THERE IS A RISK OF INJURY OR DEATH.
Estimated required man-hours to do the required actions are:
- Access: 4 hours x 2 people = 8 Man-Hours (time for venting of the tank not taken into 
account)
- CWB sealant and fastener removal = 0.5 hours x 2 people = 1 Man-Hour per A/C side
- CWB NDT inspection (rototest and HFEC) = 0.5 hours x 2 people = 1 Man-Hour per A/C side
- CWB Reaming oversize, fastener wet installation and sealant application = 0.5 hours x 2 
people = 1 Man-Hour per A/C side
- Slanted sealant and fastener removal = 0.5 hour x 1 people = 0.5 Man-Hour per A/C side
- Slanted rototest inspection = 0.5 hour x 1 people = 0.5 Man-Hour per A/C side
- Slanted sealant and fastener installation = 0.5 hour x 1 people = 0.5 Man-Hour per A/C side
- Close-up: 4 hours x 2 people = 8 Man-Hours
Elapsed time: 11 hours per A/C side
Total Man-hours: 25 Man-Hours
NOTE: The estimation does not take into account the time to vent the CWB after defueling nor the time 
to embody a repair in case of finding.

### Page 9

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 9 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5.3 ACCESS
5.3.1: To get access to areas to be inspected:
Area A. CWB rear lower spar junction area at Fr42
WARNING:
TWO PERSONS ARE NECESSARY FOR THIS PROCEDURE:
- ONE PERSON IN THE TANK TO DO THE PROCEDURE, AND
- A SECOND PERSON OUT OF THE TANK TO MONITOR THE SAFETY CONDITIONS.
IF YOU DO NOT OBEY THIS PRECAUTION, THERE IS A RISK OF INJURY OR DEATH.
CAUTION:
DO NOT USE THE FUEL PIPES AND THE EQUIPMENT AS HANDHOLDS WHEN YOU 
DO WORK IN A FUEL TANK. THIS WILL PREVENT DAMAGE TO THEM.
(1) Access the working area. Refer to Ref.[1]
(2) If necessary, remove the landing lights 7LB and 8LB to ease access. Refer to Ref.[2].
Area B. FR42 slanted beam connection area
(1) Access the working area. Open the access fairing doors, refer to Ref.[3] items 1 & 5 for door 
identification.
(2) For LHS side, if necessary remove the upper RAT access covers. Refer to Ref.[4] for part 
identification.
5.3.2: To close access to areas to be inspected:
Area A. CWB rear lower spar junction area at Fr42
(1) Close access. Refer to Ref.[1]
(2) If removed, re-install landing lights 7LB and 8LB, refer to Ref.[12]
Area B. FR42 slanted beam connection area
(1) If removed, re-install RAT access covers
(2) Close access fairing doors refer to Ref.[3] items 1 & 5 for door identification.

### Page 10

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 10 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5.4 INSPECTION (RC)
Item 1. CWB rear lower spar junction area at Fr42
WARNING:
TWO PERSONS ARE NECESSARY FOR THIS PROCEDURE:
- ONE PERSON IN THE TANK TO DO THE PROCEDURE, AND
- A SECOND PERSON OUT OF THE TANK TO MONITOR THE SAFETY CONDITIONS.
IF YOU DO NOT OBEY THIS PRECAUTION, THERE IS A RISK OF INJURY OR DEATH.
CAUTION:
DO NOT USE THE FUEL PIPES AND THE EQUIPMENT AS HANDHOLDS WHEN YOU 
DO WORK IN A FUEL TANK. THIS WILL PREVENT DAMAGE TO THEM.
The same procedure is to be applied on the Left (LH) and Right (RH) sides of the A/C:
(1) Remove the sealant around the nut identified in Figure 7 and in the rear spar lower flange.
(2) Remove the affected fastener identified in Figure 7. Refer to Ref.[5].
(3) Measure affected hole diameter and report associated value in APPENDIX 2: AOT embodiment 
reporting form.
(4) Do the HFEC inspection of the rear spar lower flange as defined in Figure 9 in accordance with 
Ref.[6], ensuring that the whole free edge is inspected from the internal rod fitting from one side 
and until the second fastener head from the other side.
Figure 9: rear spar edge HFEC inspection at FR42

### Page 11

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 11 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
(5) Do the rototest inspection on all layers of the circled hole defined in Figure 10 in accordance 
with Ref.[7].
Figure 10: Critical rear spar fastener hole at FR42 
Item 2. FR42 slanted beam connection area
The same procedure is to be applied on the Left (LH) and Right (RH) sides of the A/C:
(1) Remove the sealant and the affected fastener identified in Figures 12. Refer to Ref.[5].
(2) Do the rototest inspection on all layers of the hole located at the closest position near wing 
junction per A/C side, in accordance with Ref.[7].
Figure 11: Slanted beam fastener hole at FR42

### Page 12

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 12 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Figure 12: Slanted beam fastener hole identification per A/C side

### Page 13

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 13 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5.5 FINDINGS (RC)
Item 1. CWB rear lower spar junction area at Fr42
Potential crack findings are shown below.
Figure 13: Potential crack finding during HFEC inspection on rear spar lower edge
Note: Crack initiation could occur at any location on spar edge shown in Figure 13. The anticipated 
crack orientation and most probable initiation location is shown by the red line

### Page 14 (OCR)

AIRBUS
ALERT OPERATORS TRANSMISSION - AOT
Typical crack / Orientation (INT view):
Typical crack / Orientation (EXT view):
FWD
AOT ref: A57N020-22 Rev 00  Page 14 of 21  Date: 07-DEC-2022
C80_AOT_FM1104649_V8.0  © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT

### Page 15 (OCR)

AIRBUS
ALERT OPERATORS TRANSMISSION - AOT
Section E-E
INTERNAL FACE
Comer Fitting (8.0mm)
7175_T73_Die-Forging
Rear Spar (10mm)
7010 T7451 Plate
Fitting Front FR42 (12mm)
7175_T73_Die-Forging
Grey fitting (8 mm)
7175_T73_Die-Forging
EXTERNAL FACE
Damage location: Fitting front
Fastener: EN6115T8 (Ф12.7mm / Ti)
Cold working and medium interference
Figure 14: Potential crack finding during Rototest inspection on Frame 42 front fitting
Note: In case of finding and depending of the crack length and location, oversize, bush or additional
dedicated repair will be foreseen.
Item 2. FR42 slanted beam connection area
FWD Frame
connection
Fitting slanted
trame
- B
B-  - B
Fitting front
FR42
AOT ref: A57N020-22 Rev 00  Page 15 of 21  Date: 07-DEC-2022
C80_AOT_FM1104649_V8.0  © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT

### Page 16

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 16 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Figure 15: Potential crack finding during Rototest inspection on Frame 42 slanted junction 
(RH shown – LH symmetrical)
Note: In case of finding and depending of the crack length and location, oversize, bush or additional 
dedicated repair will be foreseen.

### Page 17

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 17 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5.6 INSTRUCTIONS (RC)
A/ CWB rear lower spar junction area at Fr42
WARNING:
TWO PERSONS ARE NECESSARY FOR THIS PROCEDURE:
- ONE PERSON IN THE TANK TO DO THE PROCEDURE, AND
- A SECOND PERSON OUT OF THE TANK TO MONITOR THE SAFETY CONDITIONS.
IF YOU DO NOT OBEY THIS PRECAUTION, THERE IS A RISK OF INJURY OR DEATH.
CAUTION:
DO NOT USE THE FUEL PIPES AND THE EQUIPMENT AS HANDHOLDS WHEN YOU 
DO WORK IN A FUEL TANK. THIS WILL PREVENT DAMAGE TO THEM.
On both A/C sides (LH and RH):
(1) In case of crack finding, contact Airbus for repair instructions
(2) If no finding is experienced, install first oversize fastener P/N EN6115T8X25 in transition fit refer 
to Ref.[5] and Ref.[8], or any approved alternative refer to Ref.[9]
(3) Restore surface protection and sealant, refer to Ref.[10] and Ref.[11]
B/ FR42 slanted beam connection area
On both A/C sides (LH and RH):
(1) If no finding is experienced during the rototest inspection, do a Detail Visual Inspection (DVI) on 
removed fastener P/N MS21250-10024 to ensure damage free condition:
a) If nil finding during the fastener DVI, check that hole diameter is still within original tolerances 
(Ø15.852 - Ø15.872mm).
If hole is within original tolerances, install removed fastener P/N MS21250-10024 with 
new nut P/N NSA5057-10. Refer to Ref.[5]. 
b) If affected fastener is found damaged and the hole diameter is within original tolerances, 
replace by a new fastener P/N MS21250-10024 with new nut P/N NSA5057-10. Refer to 
Ref.[5] or any approved alternative refer to Ref.[9].
(2) Restore surface protection and sealant, refer to Ref.[10] and Ref.[13]
(3) If finding is experienced during the rototest inspection or fastener hole found out of tolerances, 
contact Airbus for repair instructions

### Page 18

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 18 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
5.7 SPARES AND TOOLING
Equipment to do the inspections are given in Ref.[6] and Ref.[7].
This AOT is the subject of an AIRBUS monitored retrofit campaign. Before performing AOT inspection, 
Airbus recommends for each operator to refer to Retrofit Information Letter (RIL) ref. E57M22002364 
instructions for material ordering.
In the frame of the AOT inspection bellow part and quantities are needed per A/C:
1/ For CWB rear lower spar junction area at Fr42:
2EA of fastener P/N EN6115T8X25
2EA of nut P/N ASNA2531-8
2/ For FR42 slanted beam area:
Inspection: 2EA of nut of P/N NSA5057-10
In case of RAT access cover removal: 
a/ For A/C equipped with RAT cover P/N D292-70564-00000:
- 3EA of stud P/N ABS0691-015
- 1EA of stud P/N ABS0691-010
- 4EA of washer retaining P/N ABS0692-01
- 5EA of washer P/N NSA5149-4
- 1EA of screw P/N NSA5030-3-4
b/ For A/C equipped with RAT cover P/N D292-70564-00200:
- 2EA of stud P/N ABS0691-015
- 1EA of stud P/N ABS0691-010
- 3EA of washer retaining P/N ABS0692-01
- 5EA of washer P/N NSA5149-4
- 2EA of screw P/N NSA5030-3-4
NOTE: For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit 
management department: monitored.retrofit@airbus.com.

### Page 19

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 19 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
6. ADDITIONAL INFORMATION
6.1 FOLLOW-UP PLAN
TFU Ref.[14] will provide latest status of the investigation and associated additional in-service actions if 
any.
6.2 IMPACTED DOCUMENTATION
N/A
7. AOT APPROVAL
The technical content of this document is approved under the authority of the DOA ref.EASA.21J.031.
8. REPORTING
Address your inspection results (with or without findings) using AOT embodiment reporting form defined 
in Appendix 2 to Airbus Customer Services through the generic e-mail address. Refer to the latest 
reporting policy (OIT 999.0018/16 Ref.[15]).  
Give the AOT reference in the mail title, as follows: A57N020-22 Inspection Result.
Please ensure that monitoring retrofit team is also in copy of the AOT embodiment reporting by adding 
monitored.retrofit@airbus.com e-mail address. 
You can address your questions about this AOT to Airbus Customer Services through TechRequest 
on Airbus World, selecting Maintenance & Engineering Domain, Engineering Support Section and 
ATA 57-10.
Best Regards,
Ahmed CHABBOUH
SENIOR DIRECTOR IN-SERVICE ENGINEERING
CUSTOMER CARE CENTER
Jean-Pierre GOMEZ
VICE PRESIDENT A320 FAMILY PROGRAMME
CUSTOMER SERVICES

### Page 20 (OCR)

AIRBUS
ALERT OPERATORS TRANSMISSION - AOT
APPENDIX 1: AOT instructions flowchart
From the AOT effective date and within the threshold given in §5.1, perform
NDT inspections as detailed in §5.4
Crack or
damage(s) found?
Yes  No
Install new fasteners and restore
A/C conditions as detailed in §5.6
Contact Airbus for repair
instructions
Close accesses
Report to Airbus as detailed in §8
AOT ref: A57N020-22 Rev 00  Page 20 of 21  Date: 07-DEC-2022
C80_AOT_FM1104649_V8.0  © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT

### Page 21

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57N020-22 Rev 00 Page 21 of 21 Date: 07-DEC-2022
C80_AOT_FM1104649_v8.0 © AIRBUS S.A.S. 2022. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
APPENDIX 2: AOT embodiment reporting form
A/C INFORMATION:
OPERATOR:
A/C MSN:
A/C REGISTRATION:
FLIGHT CYCLES:
DATE OF INSPECTION:
INSPECTION RESULTS:
LHS hole diameter 
measurement (mm)
RHS hole diameter 
measurement (mm)
CWB Frame 42 front 
fitting diameter hole
Finding at LHS
(Yes / No)
Finding at RHS
(Yes / No)
CWB Rear Spar lower 
flange (HFEC)
CWB Frame 42 front 
fitting (Rototest)
Frame 42 slanted junction 
(Rototest)
COMMENTS (free text):

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
