# Airbus All Operators Transmission A57P013-19

Copy: No revision named ("AOT A57P013-19"), 10 pages: PDF https://openairdocs.org/files/sha256/9c/45/9c45eedaaa8e9d4de46d60fa8ad32aa5d8b3f19bb8b2f94fa6d0e0dc43d44b0c; text https://openairdocs.org/service-documents/airbus/aot-a57p013-19/file/9c45eedaaa8e.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2019-0979, the docket of AD 2020-05-18. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Other document (All Operators Transmission)
- Number: A57P013-19
- Page: https://openairdocs.org/service-documents/airbus/aot-a57p013-19

## Text (10 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2019-0979, the docket of AD 2020-05-18. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57P013-19 Rev 00 Page 1 of 10 Date: 04-APR-2019
© AIRBUS S.A.S. 2019. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
SUBJECT: ATA 57 –  Inspection of Forward Pintle Bearing Lock Washer
AIRCRAFT TYPE:  A350
OUR REF.: A57P013-19 Rev 00 dated 04 April 2019
1. AIRCRAFT AFFECTED                                          
A350-900 MSN 5-276 (except MSN 214, 224, 234, 237, 246, 249, 251, 257, 260, 265, 270, 272)
A350-1000 MSN 88-262 (except MSN 215, 229, 241)
MODEL OPR MSN
A350-900 AAR 94 117 144 176 198 218
CAL 49 57 66 73 92 105 121 138 151 162 179 191 208 239
CCA 167 178 217 231 240 247 268
CES 248 261 269
CHH 98 112 226 245
CPA 29 32 34 38 39 46 53 58 61 70 72 75 85 93 101 109 119 128 137 148 154 155
CRK 124 153 168 187 235 256
CSC 52 55 60
DAL 115 135 149 160 164 175 182 190 199 204 210 267
DLH 74 80 87 127 136 146 174 184 202 209 212 255
ETH 40 43 89 103 120 147 180 196 205 259
FBU 5 193
FIN 18 19 20 22 23 28 51 97 104 113 134 264
FWI 82 91
HVN 14 15 16 17 56 67 86 129 150 173 192 197
IBE 219 227 271
MAS 159 165 183 195 203 213
MAU 145 157
PAL 221 228 236 243
QTR 6 7 8 9 10 11 12 13 21 25 33 36 42 47 63 64 69 76 78 79 83 90 100 106 114 126 132 143 163 172 207 211
SIA 26 30 31 37 41 54 62 68 77 81 84 96 99 107 116 122 133 140 158 170 186 216 220 223 230 232 238 244 254 263 276
TAM 24 27 35 45 48 200 250
THA 44 50 95 111 123 130 142 177 181 185 189 201
A350-1000 CPA 118 169 188 206 225 233 252 258 262
QTR 88 102 110 125 141 161
2. REFERENCED DOCUMENTATION                      
2.1 APPENDIX
Appendix 1: Flow Chart
Appendix 2: Inspection Reporting Sheet

### Page 2

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57P013-19 Rev 00 Page 2 of 10 Date: 04-APR-2019
© AIRBUS S.A.S. 2019. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
2.2 REFERENCES
[1] A350 Maintenance IPD 57-26-63-02000-94AA-A – ATTACHMENT INSTL MLG
[2] MP Task A350-A-32-12-XX-00ZZZ-397Z-A – Open the MLG Doors for Maintenance
[3] NDT A350-A-51-99-XX-01001-040A-A – Visual
[4] MP TASK A350-A-57-51-71-02001-520A-A - Removal of the Lower Access Panels - 
Inboard Trailing Edge
[5] PMS 01-05-03 – Locking using tab washers
3. REASON
3.1 FACTS
A deviation to the installation of the lock washer tab at the MLG (Main Landing Gear) Forward Pintle 
Bearing, affecting the bearing nut locking, has been identified on a limited number of A350-900/A350-
1000 aircraft in production. 
The Forward Pintle Bearing is installed in the Trunnion Block and provides the connection between the 
MLG and the outer wing rear spar. The bearing nut is locked by bending one of the lock washer tabs 
into a slot around the nut circumference. 
A350-900 shown, A350-1000 similar
Figure 1 – Location of Inspection
B
C

### Page 3

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57P013-19 Rev 00 Page 3 of 10 Date: 04-APR-2019
© AIRBUS S.A.S. 2019. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
FWD
Bearing
Tab washer
Nut
C
Figure 2 – Trunnion Block Assembly
3.2 CONSEQUENCES
The absence of an engaged lock washer tab at the bearing nut could lead to an un-expected rotation of 
the nut and loss of torque. This could progressively allow an axial movement of the bearing housing. If 
no corrective action is performed, this could potentially lead to a MLG collapse.
3.3 AIM
The aim of this AOT is to provide instructions for the inspection of the MLG forward pintle bearing nut 
lock washer to check that a tab is correctly engaged and the nut is locked.
4. SHORT TERM ACTION
4.1 PLANNING AND MANPOWER
4.1.1 ACCOMPLISHMENT TIMESCALE
The inspection detailed in this AOT is expected to be mandated by an Airworthiness Directive (AD) 
published by the Airworthiness Authorities.
The inspection as described in paragraph 4.2 has to be completed at the first opportunity but no later 
than 5 months or 500FC whichever occurs first from the effective date of the associated AD.
4.1.2 MANPOWER
The estimated time to perform the inspection defined in paragraph 4.2 is 2 Man Hours per A/C. The 
inspection can be performed by one person.

### Page 4

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57P013-19 Rev 00 Page 4 of 10 Date: 04-APR-2019
© AIRBUS S.A.S. 2019. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4.2 DESCRIPTION
4.2.1 ACCESS
A standard platform or cherry picker is necessary to get access to the inspection area close to the wing 
MLG forward pintle pin trunnion assembly. Open the MLG Doors for access, refer to Ref [2].
4.2.2 INSPECTION REQUIREMENTS
NOTE: For clarification of inspection sequence, please refer to flowchart in Appendix 1.
Through this AOT, it is required to perform a Detailed Inspection (DET) as follows on the Left Hand and 
the Right Hand wing:
a. Perform a Visual Inspection (refer to ref [3]) of the bearing nut and lock washer at the forward face 
of the Trunnion block (area identified in Figure 3) to confirm that one tab of the lock washer is 
correctly bent:
The bent tab can be at any position around the nut circumference.
The lock washer is located between the trunnion block and rear spar and is 
therefore not directly visible. Any suitable tools may be used to complete this 
inspection i.e. Light, inspection mirror, borescope.
i. If the bearing nut is correctly locked by the tab washer (see example Figure 4a) no further 
action is required.
ii. If no lock washer tab is bent (see example Figure 4b) proceed to step (b)
b. Perform DET of the Bearing Assembly to Trunnion interface on the forward and aft face for 
discrepancies (sign of axial migration of the bearing assembly or rotation of the nut) as follows:
At any accessible position, use feeler gage to confirm there is no gap between the 
bearing nut / lock washer and lock washer / trunnion block (refer to Figure 6).
Be aware that the bearing nut has a chamfer of 6.0mm 
Visually inspect for gap or damage to the sealant bead at the bearing assembly to 
trunnion block aft face (area identified in Figure 5). 
i. If there is no discrepancy observed then either; before next flight perform the applicable 
corrective action defined in §4.2.3, or, to defer the corrective action, proceed to step (c).
ii. In case of discrepancy finding contact Airbus before next flight.
  
c. Apply witness mark to monitor bearing nut for evidence of rotation:
Apply witness mark using CML code 04SAB2 (Varnish Polyurethane- Marking Structure) or 
equivalent
Apply the witness mark as a continuous line, approximate width of 3.5 mm (0.14 in.), across 
the bearing housing and nut at approximately the 6 o’clock position (refer to Figure 3 for 
example).
Prior to application of witness mark clean the surface with a clean 14SBA1 (Textile_Lint free 
Cotton) and 08BAA9 (Non Aqueous Cleaner_General) or equivalent.
d. Perform Repeat DET (refer to ref [3]) at interval of 5 months or 500FC whichever occurs first, 
without exceeding 6 YRS from ToT, for evidence of nut rotation or bearing migration.
Inspect the witness mark applied in step (c) for signs of nut rotation
Visually inspect for gap or damage to the sealant bead at the bearing assembly to 
trunnion block aft face (area identified in Figure 5). 
i. In case of nut rotation or bearing migration finding during repeat inspection contact Airbus 
before next flight.
e. In all cases, including NIL FINDINGS, send the result of initial inspection to Airbus as detailed in §7. 
See Appendix 2 – Inspection Reporting Sheet.

### Page 5

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57P013-19 Rev 00 Page 5 of 10 Date: 04-APR-2019
© AIRBUS S.A.S. 2019. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Trunnion block view from below 
  
View on lock washer and nut looking aft from rear spar
Figure 3 – Area of Inspection
     
(a) Example Lock Washer Correctly Engaged (b) Example Lock washer tab not engaged
Figure 4 – Example Inspection Photos
 X
Witness 
Mark

### Page 6

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57P013-19 Rev 00 Page 6 of 10 Date: 04-APR-2019
© AIRBUS S.A.S. 2019. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Figure 5 – Trunnion Block, view looking forward
Figure 6 – Trunnion Block and Bearing Cross Section
(Extracted from Drawing V575-59333, V575-57019 & V575-56734 similar) 
Inspect Trunnion 
Block to Bearing 
interface
LOCK WASHER
BEARING NUT
BEARING HOUSING
NO GAP
CHAMFER 6.0MM
TRUNNION 
BLOCK

### Page 7

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57P013-19 Rev 00 Page 7 of 10 Date: 04-APR-2019
© AIRBUS S.A.S. 2019. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4.2.3 CORRECTIVE ACTION
In case a lock washer tab is not engaged in the bearing nut, and no sign of damage, - No later than 6 
years from first ToT (Transfer of Title) perform the applicable corrective actions to lock the nut:
i. If one tab of the lock washer is found aligned with a slot in the bearing nut, perform action A. 
ii. If no lock washer tab is aligned with a slot in the nut, perform action B1 or B2.
A. Bend the washer tab to lock the bearing nut, refer to PMS 01-05-03. Note:
Any suitable means can be used to bend the tab of the lock washer. However, due 
to very limited access, Airbus is currently developing specific tools to enable the tab 
to be bent at any circumferential position. Contact Airbus for further 
recommendations on a case-by-case basis.
Do not use steel or other hard metal tools which could damage the lock washer or 
surrounding structure.
Removal of panel 571CB (671CB) may be required to improve access when 
performing  corrective action. Refer to Ref [4].
B1. Perform Corrective Action with MLG removal in accordance with Ref R57V-40094. 
 
B2. Corrective Action instructions without MLG removal will be provided in a revision of this 
AOT, expected in Q3/2019. 
Specific tools and instructions to enable the bearing nut to be re-torqued and the lock 
washer tab to be bent without MLG removal are currently under development by Airbus. 
4.3 SPARES AND TOOLING
No specific tooling is required to perform this inspection.
5. FURTHER INFORMATION
5.1 FOLLOW-UP PLAN
This AOT is expected to be mandated by an Airworthiness Directive (AD) published by the 
Airworthiness Authorities. 
A revision of the AOT is considered for Q3/2019 to provide alternative corrective action instructions in 
case of finding the bearing nut not locked and not aligned with the tab washer.
5.2 IMPACTED DOCUMENTATION
No specific documentation is impacted.
6. AOT APPROVAL
The technical content of this document is approved under the authority of DOA nr. EASA.21J.031.
7. REPORTING

### Page 8

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57P013-19 Rev 00 Page 8 of 10 Date: 04-APR-2019
© AIRBUS S.A.S. 2019. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Questions about this AOT are to be addressed to Airbus Customer Services through TechRequest on 
Airbus World, selecting Engineering Domain (Engineering Support) and ATA 57-26.
As per latest reporting policy (Ref to OIT 999.0018/16), inspection results (with or without findings) are to 
be addressed to Airbus Customer Services through the generic e-mail 
address:  inspection.results@airbus.com.
Best Regards, 
Christian FREMONT
VICE PRESIDENT ENGINEERING SUPPORT
CUSTOMER SERVICES
Stephane GOSSELIN
VICE PRESIDENT A350  PROGRAMME
CUSTOMER SERVICES

### Page 9

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57P013-19 Rev 00 Page 9 of 10 Date: 04-APR-2019
© AIRBUS S.A.S. 2019. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
APPENDIX 1 – Inspection Flow Chart
Within 500FC or 5Months whichever 
occurs first from AD issue date
Perform DET of MLG Bearing Lock Washer
LH AND RH Wing
Is the Bearing Nut 
correctly locked by 
tab washer?
No Further Action 
Required
Discrepancy 
observed?
YES
YES
NO
NO
A – Aligned Tab Washer
Lock tab washer refer to 
PMS 01-05-03
Contact AIRBUS 
before next flight
Perform Repeat DET
Interval: 500FC / 5 Months
Limit: 6YRS from ToT
OR Apply Witness Mark
Rotation or 
migration?
YES
NO
Contact AIRBUS 
before next flight
OR
B2 – Misaligned Tab Washer
Await AOT Revision for RI 
without MLG removal
B1 – Misaligned Tab Washer
Perform Corrective Action with 
MLG removal per R57V-40094
Perform applicable  
Corrective Action
No Further Action 
Required

### Page 10

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A57P013-19 Rev 00 Page 10 of 10 Date: 04-APR-2019
© AIRBUS S.A.S. 2019. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
APPENDIX 2 – Inspection Report Form
A/C INFORMATION:
OPERATOR:
A/C MSN:
A/C REGISTRATION:
FLIGHT CYCLES
FLIGHT HOURS:
DATE OF INSPECTION:
INSPECTION RESULT:
LH WING RH WING
LOCK WASHERTAB BENT AND 
CORRECTLY LOCKED? (Y/N)
CORRECTIVE ACTIONS:
In case of finding, report the actions performed at time of inspection:
LH WING RH WING
IS LOCK WASHER TAB ALIGNED WITH 
NUT SLOT? (Y/N)
WITNESS MARK APPLED, CORRECTIVE 
ACTION DEFERRED (Y/N)
COMMENTS:

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
