# Airbus Service Bulletin 28-0092

Copy: Revision 1 ("SB_28-0092_r01"), 65 pages: PDF https://openairdocs.org/files/sha256/7f/b5/7fb52722a0340b16c060c85aa1dd18da03183ee4e988de8e3890c2748f5ae4a3; text https://openairdocs.org/service-documents/airbus/sb-28-0092/file/7fb52722a034.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2017-0714, the docket of AD 2017-25-09. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: 28-0092
- Latest revision known: 28-0092, Revision 1 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus/sb-28-0092

## Text (65 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2017-0714, the docket of AD 2017-25-09. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

@A300
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
ATA SYSTEM: 28
TITLE: FUEL - MAIN FUEL PUMP SYSTEM - INSTALL FUEL PUMP CANISTER
WITH NEW HOOD/MESH IN INNER AND CENTER TANK POSITIONS
MODIFICATION No.: 13644H5743 13739H5755
This page transmits Revision No.01 of Service Bulletin No.A300-28-0092
ADDITIONAL WORK
**CONF ALL
Additional work is required by this revision for aircraft modified by the original issue of this Service
Bulletin.
REASON
Revision No. 01 issued to:
- add modification No. 13739H5755 (Introduction of Longer Screws at the outer positions on the
canister hoods for Post-MOD 13644)
- update the procurement address in paragraph 2.A.(1).
The opportunity is taken to make minor format changes.
CHANGES
FRONT MATTER
MODIFICATIONS
 MODIFICATION NUMBER(S) UPDATED
 R
SUMMARY
MODIFICATIONS
 MODIFICATION CLASSIFICATION UPDATED
 R
MANPOWER
 MANPOWER UPDATED
 R
MANPOWER UPDATED
 R
PLANNING INFORMATION
EFFECTIVITY
 EFFECTIVITY RELATED INFORMATION
UPDATED
R
Configuration definition
CONF 002
 CONFIGURATION DEFINITION UPDATED
 R
Material Effectivity
 MATERIAL EFFECTIVITY UPDATED
MATERIAL SET QUANTITY UPDATED
MATERIAL SET UPDATED
R
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 2

@A300
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
MATERIAL EFFECTIVITY UPDATED
MATERIAL SET QUANTITY UPDATED
MATERIAL SET UPDATED
R
APPROVAL
 APPROVAL UPDATED
 R
MANPOWER
 MANPOWER UPDATED
 R
MANPOWER UPDATED
CONFIGURATION UPDATED
R
MANPOWER UPDATED
CONFIGURATION UPDATED
R
REFERENCES
 REFERENCED DOCUMENTATION UPDATED
 R
REFERENCED DOCUMENTATION UPDATED
 R
INTERCHANGEABILITY/MIXABILITY
 INTERCHANGEABILITY/MIXABILITY UPDATED
 R
INTERCHANGEABILITY/MIXABILITY UPDATED
 R
MATERIAL INFORMATION
MATERIAL - PRICE AND AVAILABILITY
Procurement Addresses
 PROCUREMENT ADDRESSES UPDATED
 R
LIST OF MATERIALS - OPERATOR
SUPPLIED
Equipment
Equipement BFEB01
 PART MATERIAL SET UPDATED
PART NUMBER UPDATED
R
Equipement BFEB02
 PART MATERIAL SET UPDATED
PART NUMBER UPDATED
R
PARTS TO BE RE-IDENTIFIED BY
OPERATOR
PARTS TO BE RE-IDENTIFIED BY OPERATOR
UPDATED
R
Reidentified part set REIDB01
 PART MATERIAL SET UPDATED
PART NUMBER UPDATED
R
Reidentified part set REIDB02
 PART MATERIAL SET UPDATED
QUANTITY UPDATED
PART NUMBER UPDATED
R
Reidentified part set REIDB03
 PART MATERIAL SET ADDED
 N
Reidentified part set REIDB04
 PART MATERIAL SET ADDED
 N
ACCOMPLISHMENT INSTRUCTIONS
TASK 280092- 831-895-001-Modification
 TASK SOLUTION UPDATED
CAUTION UPDATED
NOTE UPDATED
R
Task associated data - 001
 ZONE UPDATED
PANEL UPDATED
R
Subtask 280092-910-401-001
 SUBTASK SOLUTION UPDATED
REFERENCED DOCUMENTATION UPDATED
REFERENCES UPDATED
R
Subtask 280092-910-401-001
 SUBTASK SOLUTION UPDATED
REFERENCED DOCUMENTATION UPDATED
REFERENCES UPDATED
R
Subtask 280092-941-401-001
 SUBTASK SOLUTION UPDATED
NOTE UPDATED
R
Subtask 280092-941-401-002
 SUBTASK SOLUTION UPDATED
NOTE UPDATED
R
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 2
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 3

@A300
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
Subtask 280092-831-401-001
 SUBTASK SOLUTION UPDATED
PANEL UPDATED
ZONE UPDATED
PART NUMBER UPDATED
LOCATION UPDATED
MATERIAL LIST UPDATED
R
Subtask 280092-930-401-001
 SUBTASK SOLUTION UPDATED
PART NUMBER UPDATED
MATERIAL LIST UPDATED
R
Subtask 280092-831-401-002
 SUBTASK SOLUTION UPDATED
PART NUMBER UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
MATERIAL LIST UPDATED
R
Subtask 280092-930-401-002
 SUBTASK SOLUTION UPDATED
PART NUMBER UPDATED
MATERIAL LIST UPDATED
R
Subtask 280092-700-401-001
 SUBTASK SOLUTION UPDATED
 R
Subtask 280092-700-401-001
 SUBTASK SOLUTION UPDATED
 R
Subtask 280092-942-401-001
 SUBTASK SOLUTION UPDATED
 R
Subtask 280092-942-401-002
 SUBTASK SOLUTION UPDATED
 R
TASK 280092- 831-896-001-Modification
for aircraft that have accomplished this
Service Bulletin at Rev 00 - ADDITIONAL
WORK
TASK SOLUTION ADDED
 N
Task associated data - 001
 TASK ASSOCIATED DATA ADDED
 N
Task associated data - 002
 TASK ASSOCIATED DATA ADDED
 N
Subtask 280092-910-402-001
 SUBTASK SOLUTION ADDED
 N
Subtask 280092-839-402-001
 SUBTASK SOLUTION ADDED
 N
Subtask 280092-910-402-001
 SUBTASK SOLUTION ADDED
 N
Subtask 280092-839-402-001
 SUBTASK SOLUTION ADDED
 N
Subtask 280092-941-402-001
 SUBTASK SOLUTION ADDED
 N
Subtask 280092-941-402-002
 SUBTASK SOLUTION ADDED
 N
Subtask 280092-831-402-001
 SUBTASK SOLUTION ADDED
 N
Subtask 280092-930-402-001
 SUBTASK SOLUTION ADDED
 N
Subtask 280092-831-402-002
 SUBTASK SOLUTION ADDED
 N
Subtask 280092-930-402-002
 SUBTASK SOLUTION ADDED
 N
Subtask 280092-700-402-001
 SUBTASK SOLUTION ADDED
 N
Subtask 280092-700-402-001
 SUBTASK SOLUTION ADDED
 N
Subtask 280092-942-402-001
 SUBTASK SOLUTION ADDED
 N
Subtask 280092-942-402-002
 SUBTASK SOLUTION ADDED
 N
Appendix 01 - Elapsed Time Assumption
Fig. A-UAAAB
 FIGURE SOLUTION ADDED
 N
Fig. A-UAAAB Sheet 01
 SHEET ADDED
 N
Fig. A-UABAA
 FIGURE SOLUTION UPDATED
CONFIGURATION UPDATED
R
Fig. A-UABAA Sheet 01
 SHEET UPDATED
 R
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 3
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 4

@A300
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
Fig. A-UABAB
 FIGURE SOLUTION ADDED
 N
Fig. A-UABAB Sheet 01
 SHEET ADDED
 N
FILLING INSTRUCTIONS
This Service Bulletin has been generated electronically and is reissued as a complete document.
Replace the complete document.
Put this Revision Transmittal Sheet in front of the Service Bulletin.
HISTORY OF PREVIOUS REVISIONS
No previous revision
REVISION SEQUENCE
ORIGINAL: Dec 12/13
REVISION No. : 01 - Aug 29/14
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 4
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 5

@A300
SERVICE BULLETIN
SUMMARY
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
This summary is for information only and is not approved for modification of the aircraft.
ATA SYSTEM: 28
TITLE: FUEL - MAIN FUEL PUMP SYSTEM - INSTALL FUEL PUMP CANISTER
WITH NEW HOOD/MESH IN INNER AND CENTER TANK POSITIONS
**CONF ALL
MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR
 13644H5743
MINOR
 13739H5755
NOTE
: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting the
airworthiness of the product. All other changes are major changes.
REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
Fuel pump canisters are located in pairs in all fuel tanks. There is a fabricated aluminium hood (in two
halves) which forms a surface between the fuel pump inlet mesh and the fuel pump canister body.
Some operators have reported cases of cracking on the hood in the inner wing fuel tanks. On one
aircraft, part of the hood detached and was found inside the fuel tank.
Fuel pump canister hoods are currently subject to a mandatory inspection in accordance with Inspection
Service Bulletin A300-28-0089.
Following the investigation into in-service failures, this Service Bulletin introduces new canister hoods
for the wing inner tank and the center tank fuel pumps (where fitted) only. No other fuel pump positions
are affected by this Service Bulletin.
The new design consists of a new two part stainless steel hood assembly that is installed over the
existing inlet mesh as before. To account for tolerances in the inlet mesh diameter and to avoid
installation pre-stress, each hood half has an enlarged central hole, through which a stepped fastener is
installed.
Accomplishment of this Service Bulletin will reduce the scope of the Inspection Service Bulletin
A300-28-0089 and will be captured in any future Airworthiness Directive. Accomplishment of this
Service Bulletin will also cancel the repeat inspection requirement of the inner wing and center tanks
(only).
The installation of a new fuel pump canister hood changes the part number of the canister assembly.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 6

@A300
SERVICE BULLETIN
SUMMARY
GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE
 RECOMMENDED (1)
 CANCELS INSPECTION SB
 NO
POTENTIAL AD
 NO
 A/C OPERATION AFFECTED
 NO
RELIABILITY AFFECTED
 NO
 PAX COMFORT AFFECTED
 NO
COST SAVING
 NO
 ETOPS AFFECTED
 NO
STRUCTURAL LIFE EXTN
 NO
 VENDOR SB INVOLVED
 NO
DEFUEL/VENTILATION
 YES
 PRE-ENTRY CHECKLIST
 YES
NOTE
 (1)
: Service Bulletin recommended to be accomplished to prevent significant operational
disruptions.
MATERIAL PRICE INFORMATION
**CONF 001
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET
 QTY PER
A/C
PRICE PER
A/C (USD)
MAIN PARTS
Equipment BFEB01
 4
 See SB
 Hood Halves and Attachments
**CONF 002
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET
 QTY PER
A/C
PRICE PER
A/C (USD)
MAIN PARTS
Equipment BFEB01
 4
 See SB
 Hood Halves and Attachments
Equipment BFEB02
 2
 See SB
 Hood Halves and Attachments
EFFECTIVITY
**CONF ALL
This Service Bulletin is applicable to this (these) operator(s) :
001 50W 81T ABR AFG F2I IAW IRA IRM KZU MNB MSR RUN
SOP TIW TNO TSY
CONCURRENT REQUIREMENTS
None
REFERENCES / REPERCUSSIONS
TFU
 None
OEB
 None
AOT
 None
SIL
 None
LINE MAINTENANCE AFFECTED
 No
LIFE LIMIT
 None
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 2
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 7

@A300
SERVICE BULLETIN
SUMMARY
OTHER
 None
NATURE OF THE WORK
AIRCRAFT
 YES
EQUIPMENT
 YES
HARD
 NO
SOFT
 NO
OBRM
 NO
MANPOWER
**CONF 001
Task 280092-831-895-001: Modification
TOTAL MANHOURS
 11.00
ELAPSED TIME (HOURS)
 7.00
Task 280092-831-896-001: Modification for aircraft that have accomplished this Service Bulletin
at Rev 00 - ADDITIONAL WORK
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 5.00
**CONF 002
Task 280092-831-895-001: Modification
TOTAL MANHOURS
 15.00
ELAPSED TIME (HOURS)
 9.00
Task 280092-831-896-001: Modification for aircraft that have accomplished this Service Bulletin
at Rev 00 - ADDITIONAL WORK
TOTAL MANHOURS
 9.00
ELAPSED TIME (HOURS)
 6.00
APPENDICES
**CONF ALL
Appendix 01 - Elapsed Time Assumption
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 3
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 8

@A300
SERVICE BULLETIN
SUMMARY
**CONF 001
TYPICAL TYPICAL
RIB2
LH WING SHOWN
RH WING SIMILAR
Z542 (Z642)A
A
A
B
B C
C
BEFORE AFTER
NOTE:
AREA OF MODIFICATION.
FUEL PUMP
CANISTER
HOOD HALF
FUEL PUMP
CANISTER
HOOD HALF
A_SB_280092_7_SAAA_01_01
Figure A-USAAA - Sheet 01
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 4
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 9

@A300
SERVICE BULLETIN
SUMMARY
**CONF 002
A B
BEFORE
TYPICAL
AFTER
TYPICAL
C D
RIB2
LH WING SHOWN
RH WING SIMILAR
FR46
FR47
Z542 (Z642)
A
B
FUEL PUMP
CANISTER
HOOD HALF
FUEL PUMP
CANISTER
HOOD HALF
C
C
C
NOTE:
AREA OF MODIFICATION.
D
A_SB_280092_7_SBAA_01_00
 − Z142Z141
B
Figure A-USBAA - Sheet 01
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 5
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 10

@A300
SERVICE BULLETIN
SUMMARY
This Page Intentionally Left Blank
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 6
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 11

@A300
SERVICE BULLETIN
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
ATA SYSTEM: 28
TITLE: FUEL - MAIN FUEL PUMP SYSTEM - INSTALL FUEL PUMP CANISTER
WITH NEW HOOD/MESH IN INNER AND CENTER TANK POSITIONS
MODIFICATION No.: 13644H5743 13739H5755
This document contains AIRBUS PROPRIETARY INFORMATION and shall at all times remain the
property of AIRBUS; no intellectual property right or licence is granted by AIRBUS in connection with
any information contained in it. It is delivered on the express condition that said document and the
information contained in it shall be treated as confidential, shall not be used for any purpose other than
that for which it is hereby delivered. It shall not be disclosed in whole or in part to third parties and shall
not be duplicated in any manner (except for the purposes of performing the tasks described hereunder
and provided that any recipient of such document shall comply with the conditions herein), without
AIRBUS prior written consent.
1. PLANNING INFORMATION
**CONF ALL
A. EFFECTIVITY
(1) Models
B2-1C B2-203 B2K-3C B4-103 B4-203 B4-2C C4-203 F4-203
(2) Effectivity by MSN
0003 0045 0055 0075 0080 0090 0101 0105 0107 0117 0126 0129 0139 0151-0152
0154 0157 0160 0173 0175 0180 0183 0185 0187 0200 0203-0204 0210 0212 0218
0220 0226-0227 0234-0236 0239 0244 0247 0255-0256 0259 0261 0274 0277 0292
0299 0302
(3) Effectivity by Operator
The Operator/MSN relationship is provided for information only and is correct at the time
of issue in accordance with the information available to AIRBUS. Any future changes
resulting from transfer of an aircraft from one operator to another will not be reflected in
this list unless the Service Bulletin is revised for another reason.
OPERATOR
 MSN
001
 0203 0218
50W
 0003
81T
 0157 0277 0292
ABR
 0152 0220 0259 0274
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 12

@A300
SERVICE BULLETIN
OPERATOR
 MSN
AFG
 0180
F2I
 0235
IAW
 0239
IRA
 0080 0139 0151 0173 0185 0187 0226 0256 0299 0302
IRM
 0055 0090 0160 0175 0204 0244
KZU
 0101 0117
MNB
 0212
MSR
 0200 0255
RUN
 0075 0105 0107 0154 0183
SOP
 0126
TIW
 0234
 0236
 0261
TNO
 0045 0210 0227 0247
TSY
 0129
(4) Configuration by MSN
MSN
 CONFIGURATION
0003 0080 0090 0160 0185 0187 0226 0244
 001
0045 0055 0075 0101 0105 0107 0117 0126 0129 0139 0151
0152 0154 0157 0173 0175 0180 0183 0200 0203 0204 0210
0212 0218 0220 0227 0234 0235 0236 0239 0247 0255 0256
0259 0261 0274 0277 0292 0299 0302
002
(5) Configuration definition
NOTE
: This Service Bulletin is only applicable to A300 aircraft that have Fuel
Pump Canister Hood PN 205481 (part of Fuel Pump Canister PN
2052C11 or PN 2052C12) or PN 3C93-129 (part of Fuel Pump Canister
PN C93R51-601) installed.
**CONF 001
Config. 001 is applicable to aircraft without a center tank installed (Aircraft Model B2).
**CONF 002
Config. 002 is applicable to aircraft with a center tank installed (Aircraft Model B4).
(6) Material Effectivity
**CONF 001
MATERIAL
 QTY PER A/C
 SEE NOTES
Consumable CMLB01
 As required
Equipment BFEB01
 4
 (1)
Reidentified part set REIDB01
 1
Reidentified part set
 REIDB03
 1
 (2
)
NOTE
 (1)
: One Kit BFEB01 is required for each Wing Inner Tank Fuel Pump
Canister.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 2
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 13

@A300
SERVICE BULLETIN
NOTE
 (2)
: Matset REIDB03 is required by aircraft in Config. 001 to accomplish the
Additional Work.
**CONF 002
MATERIAL
 QTY PER A/C
 SEE NOTES
Consumable CMLB01
 As required
Equipment BFEB01
 4
 (1)
Equipment BFEB02
 2
 (2)
Reidentified part set REIDB02
 1
Reidentified part set
 REIDB04
 1
 (3
)
NOTE
 (1)
: One Kit BFEB01 is required for each Wing Inner Tank Fuel Pump
Canister.
NOTE
 (2)
: One Kit BFEB02 is required for each Center Tank Fuel Pump Canister.
NOTE
 (3)
: Matset REIDB04 is required by aircraft in Config. 002 to accomplish the
Additional Work.
**CONF ALL
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
Fuel pump canisters are located in pairs in all fuel tanks. There is a fabricated aluminium
hood (in two halves) which forms a surface between the fuel pump inlet mesh and the
fuel pump canister body.
Some operators have reported cases of cracking on the hood in the inner wing fuel
tanks. On one aircraft, part of the hood detached and was found inside the fuel tank.
Fuel pump canister hoods are currently subject to a mandatory inspection in accordance
with Inspection Service Bulletin A300-28-0089.
(2) Objective/Action
Following the investigation into in-service failures, this Service Bulletin introduces new
canister hoods for the wing inner tank and the center tank fuel pumps (where fitted) only.
No other fuel pump positions are affected by this Service Bulletin.
The new design consists of a new two part stainless steel hood assembly that is
installed over the existing inlet mesh as before. To account for tolerances in the inlet
mesh diameter and to avoid installation pre-stress, each hood half has an enlarged
central hole, through which a stepped fastener is installed.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 3
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 14

@A300
SERVICE BULLETIN
(3) Advantages
Accomplishment of this Service Bulletin will reduce the scope of the Inspection
Service Bulletin A300-28-0089 and will be captured in any future Airworthiness
Directive. Accomplishment of this Service Bulletin will also cancel the repeat inspection
requirement of the inner wing and center tanks (only).
The installation of a new fuel pump canister hood changes the part number of the
canister assembly.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
To accomplish this Service Bulletin it is necessary to :
**CONF 001
Task 280092-831-895-001: Modification
(1) Replace the Pump Canister Hood Halves
(2) Re-Identification
Task 280092-831-896-001: Modification for aircraft that have accomplished this Service
Bulletin at Rev 00 - ADDITIONAL WORK
(1) Replace the Outer Attachment Screws of the Fuel Pump Canister Hood Halves
(2) Re-identification
**CONF 002
Task 280092-831-895-001: Modification
(1) Replace the Pump Canister Hood Halves
(2) Re-Identification
Task 280092-831-896-001: Modification for aircraft that have accomplished this Service
Bulletin at Rev 00 - ADDITIONAL WORK
(1) Replace the Outer Attachment Screws of the Fuel Pump Canister Hood Halves
(2) Re-identification
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 4
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 15

@A300
SERVICE BULLETIN
**CONF ALL
E. COMPLIANCE
(1) Classification
RECOMMENDED: Service Bulletin recommended to be accomplished to prevent
significant operational disruptions.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin is recommended at the earliest opportunity
where manpower and facilities are available.
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No.
 EASA.21J.031.
If an aircraft listed in the effectivity has a modification or repair embodied that is not of
AIRBUS origin, and which affects the content of this Service Bulletin, the operator is
responsible for obtaining approval by its airworthiness authority for any adaptation necessary
before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also not
included.
**CONF 001
Task 280092-831-895-001: Modification
Get Access
 1.00
On Aircraft
Replace the Pump Canister Hood Halves
 8.00
Re-Identification
 1.00
Close-Up
 1.00
TOTAL MANHOURS
 11.00
ELAPSED TIME (HOURS)
 7.00
NOTE
: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA
 given in Appendix 01 - Elapsed Time Assumption
 .
Task 280092-831-896-001: Modification for aircraft that have accomplished this Service Bulletin
at Rev 00 - ADDITIONAL WORK
Get Access
 1.00
On Aircraft
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 5
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 16

@A300
SERVICE BULLETIN
Task 280092-831-896-001: Modification for aircraft that have accomplished this Service Bulletin
at Rev 00 - ADDITIONAL WORK
Replace the Outer Attachment Screws of the Fuel
Pump Canister Hood Halves
4.00
Re-identification
 1.00
Close-Up
 1.00
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 5.00
NOTE
: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UABAA
 given in Appendix 01 - Elapsed Time Assumption
 .
**CONF 002
Task 280092-831-895-001: Modification
Get Access
 1.00
On Aircraft
Replace the Pump Canister Hood Halves
 12.00
Re-Identification
 1.00
Close-Up
 1.00
TOTAL MANHOURS
 15.00
ELAPSED TIME (HOURS)
 9.00
NOTE
: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAB
 given in Appendix 01 - Elapsed Time Assumption
 .
Task 280092-831-896-001: Modification for aircraft that have accomplished this Service Bulletin
at Rev 00 - ADDITIONAL WORK
Get Access
 1.00
On Aircraft
Replace the Outer Attachment Screws of the Fuel
Pump Canister Hood Halves
6.00
Re-identification
 1.00
Close-Up
 1.00
TOTAL MANHOURS
 9.00
ELAPSED TIME (HOURS)
 6.00
NOTE
: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UABAB
 given in Appendix 01 - Elapsed Time Assumption
 .
**CONF ALL
H. WEIGHT AND BALANCE
**CONF 001
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer’s Empty Weight (MEW) and do not include operator’s items. For the definition of
MEW and operator’s items, refer to the Weight and Balance Manual (WBM) Chapter 1-00-07.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 6
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 17

@A300
SERVICE BULLETIN
Manufacturers Empty Weight +0.560 KG (+1.2345 LB)
Effect on Balance +16.706 KGM (+120.834 LB.FT )
**CONF 002
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer’s Empty Weight (MEW) and do not include operator’s items. For the definition of
MEW and operator’s items, refer to the Weight and Balance Manual (WBM) Chapter 1-00-07.
Manufacturers Empty Weight +0.860 KG (+1.8959 LB)
Effect on Balance +25.6151 KGM (+185.2740 LB.FT )
**CONF ALL
I. ELECTRICAL LOAD DATA
Not Changed
J. REFERENCES
**CONF 001
Aircraft Maintenance Manual (AMM)
 06-21-00 06-21-53 06-21-57
20-21-12
 28-00-00 28-10-00
28-11-14
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM)
 20-55-00
Process and Material Specification (PMS)
 Process and Material Specification
(PMS) 01-06-12
Standards Manual (SM)
Weight and Balance Manual (WBM)
 Chapter 1-00-07
**CONF 002
Aircraft Maintenance Manual (AMM)
 06-21-00 06-21-53 06-21-57
20-21-12
 28-00-00 28-10-00
28-11-14
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM)
 20-55-00
Process and Material Specification (PMS)
 Process and Material Specification
(PMS) 01-06-12
Standards Manual (SM)
Weight and Balance Manual (WBM)
 Chapter 1-00-07
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 7
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 18

@A300
SERVICE BULLETIN
**CONF ALL
K. PUBLICATION AFFECTED
**CONF 001
Illustrated Parts Catalog (IPC)
 28-21-13
**CONF 002
Illustrated Parts Catalog (IPC)
 28-21-13 28-21-03
**CONF ALL
L. INTERCHANGEABILITY/MIXABILITY
**CONF 001
DESCRIPTION
 OLD PART N˚
 NEW PART N˚
 INT
 MIXABILITY
 SEE
NOTES
Screw
 MS35206-228
 C93-463
 01
 NO
Hood Half
 205481
 C93-467
 01
 NO
Washer
 AN935-6L
 Z4U
 01
 NO
Screw
 MS35206-228
 MS35206-228
 01
 NO
Fuel Pump Canister
 2052C11
 2052C11-5
 01
 NO
Fuel Pump Canister
 2052C12
 2052C12-5
 01
 NO
NOTE
: For definitions of interchangeability codes in column INT., refer to ATA
Common Support Data Dictionary (CSDD), Chapter 2.
NOTE
: Only the mixability configuration(s) and condition(s) stated in this Service
Bulletin are approved.
**CONF 002
DESCRIPTION
 OLD PART N˚
 NEW PART N˚
 INT
 MIXABILITY
 SEE
NOTES
Screw
 MS35206-228
 C93-463
 01
 NO
Hood Half
 205481
 C93-467
 01
 NO
Washer
 AN935-6L
 Z4U
 01
 NO
Screw
 MS35206-228
 MS35206-228
 01
 NO
Hood Half
 3C93-129
 C93-467
 01
 NO
Fuel Pump Canister
 2052C11
 2052C11-5
 01
 NO
Fuel Pump Canister
 2052C12
 2052C12-5
 01
 NO
Fuel Pump Canister
 C93R51-601
 C93R51-601-5
 01
 NO
NOTE
: For definitions of interchangeability codes in column INT., refer to ATA
Common Support Data Dictionary (CSDD), Chapter 2.
NOTE
: Only the mixability configuration(s) and condition(s) stated in this Service
Bulletin are approved.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 8
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 19

@A300
SERVICE BULLETIN
**CONF ALL
M. SPARES
None
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 9
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 20

@A300
SERVICE BULLETIN
This Page Intentionally Left Blank
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 10
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 21

@A300
SERVICE BULLETIN
2. MATERIAL INFORMATION
**CONF ALL
A. MATERIAL - PRICE AND AVAILABILITY
(1) Procurement Addresses
Vendor parts are to be procured from:
Equipment BFEB01
Equipment BFEB02
For Europe, Middle East, Africa
ZODIAC AEROSPACE
61 Rue Pierre Curie CS20001
78373 Plaisir Cedex
FRANCE
Phone: +33 161 34 23 23
Phone AOG: +33 172 02 23 23
Fax:+33 161 34 21 08
For USA
ZODIAC AEROSPACE
4900 St Joe Boulevard
Building 200 Suite 400
College Park
GA 30337
USA
Phone: +1 678 228 8153
Phone AOG: +1 800 879 0411
Fax:+1 404 559 0041
For Asia
ZODIAC AEROSPACE
36 Loyang Drive
Singapore 508949
Phone: +65 6579 2230
Phone AOG: +655 9770 5061
Fax:+65 65579 2231
(2) Price and Availability
No AIRBUS kit will be provided.
Procurement terms for the equipment must be negotiated with the equipment supplier.
B. INDUSTRY SUPPORT INFORMATION
AIRBUS will not provide industry support for accomplishment of this Service Bulletin.
C. LIST OF COMPONENTS
No Kit
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 11
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 22

@A300
SERVICE BULLETIN
D. LIST OF MATERIALS - OPERATOR SUPPLIED
(1) Consumable Materials
Consumable CMLB01
ITEM
 DESCRIPTION
 REFERENCE TO CML
MAT. No.
QTY PER A/C
 SEE
NOTES
Solvent
 08BBH1
 As required
Lint-Free Cotton Cloth
 14SBA1
 As required
(2) Components
None
(3) Equipment
Equipment BFEB01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
1
 C93-467
 2
 HOOD
 (1)
 205481
 01
2
 MS35206-228
 4
 SCREW
 (2)
 MS35206-228
 01
3
 Z4U
 4
 WASHER
 (3)
 AN935-6L
 01
5
 C93-463
 2
 SCREW
 (2)
 MS35206-228
 01
NOTE
: For definitions of interchangeability codes in column INT., refer to ATA
Common Support Data Dictionary (CSDD), Chapter 2.
NOTE
: If you find part numbers of hardware components in the related kit(s)
which you cannot identify in the LIST OF COMPONENTS of this Service
Bulletin, refer to Standards Manual (SM). The SM will give you the
correct part number to part number relationship.
NOTE
: One Kit is required for each Wing Inner Tank Fuel Pump Canister.
NOTE
: To order Kit BFEB01 from the Vendor quote kit ref. KC93-465-1.
NOTE
: PN G704900 is an acceptable alternative to MS35206-228.
Equipment BFEB02
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
1
 C93-467
 2
 HOOD
 (4)
 3C93-129
 01
2
 MS35206-228
 4
 SCREW
 (2)
 MS35206-228
 01
3
 Z4U
 4
 WASHER
 (3)
 AN935-6L
 01
5
 C93-463
 2
 SCREW
 (2)
 MS35206-228
 01
NOTE
: For definitions of interchangeability codes in column INT., refer to ATA
Common Support Data Dictionary (CSDD), Chapter 2.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 12
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 23

@A300
SERVICE BULLETIN
NOTE
: If you find part numbers of hardware components in the related kit(s)
which you cannot identify in the LIST OF COMPONENTS of this Service
Bulletin, refer to Standards Manual (SM). The SM will give you the
correct part number to part number relationship.
NOTE
: One Kit is required for each Center Tank Fuel Pump Canister.
NOTE
: To order Kit BFEB02 from the Vendor quote kit ref. KC93-465-1.
NOTE
: PN G704900 is an acceptable alternative to MS35206-228.
E. PARTS TO BE RE-IDENTIFIED BY OPERATOR
Reidentified part set REIDB01
ITEM
 NEW PART N˚
 KEYWORD
 ITEM
 OLD PART N˚
 SEE
NOTES
2052C11-5
 CANISTER
 2052C11
2052C12-5
 CANISTER
 2052C12
Reidentified part set REIDB02
ITEM
 NEW PART N˚
 KEYWORD
 ITEM
 OLD PART N˚
 SEE
NOTES
2052C11-5
 CANISTER
 2052C11
2052C12-5
 CANISTER
 2052C12
C93R51-601-5
 CANISTER
 C93R51-601
Reidentified part set REIDB03
ITEM
 NEW PART N˚
 KEYWORD
 ITEM
 OLD PART N˚
 SEE
NOTES
2052C11-5
 CANISTER
 2052C11-4
2052C12-5
 CANISTER
 2052C12-4
NOTE
: Matset REIDB03 is required by aircraft in Config. 001 to accomplish the
Additional Work.
Reidentified part set REIDB04
ITEM
 NEW PART N˚
 KEYWORD
 ITEM
 OLD PART N˚
 SEE
NOTES
2052C11-5
 CANISTER
 2052C11-4
2052C12-5
 CANISTER
 2052C12-4
C93R51-601-5
 CANISTER
 C93R51-601-4
NOTE
: Matset REIDB04 is required by aircraft in Config. 002 to accomplish the
Additional Work.
F. TOOLING
None
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 13
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 24

@A300
SERVICE BULLETIN
This Page Intentionally Left Blank
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 14
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 25

@A300
SERVICE BULLETIN
3. ACCOMPLISHMENT INSTRUCTIONS
Task 280092-831-895-001 - Modification
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
WARNING
: THIS INSTRUCTION IS APPLICABLE TO A CRITICAL DESIGN
CONFIGURATION CONTROL LIMITAT ION (CDCCL). CAREFULLY OBEY ALL
GIVEN INSTRUCTIONS WHEN YOU DO THIS STEP. IF YOU DO NOT OBEY
THESE INSTRUCTIONS, A DANGEROU S CONDITION CAN OCCUR THAT CAN
CAUSE A POSSIBLE FUEL TANK EXPLOSION.
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC; AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
Task Associated Data
**CONF 001
Zone
542 642
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 15
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 26

@A300
SERVICE BULLETIN
Modified FIN
280014 280015 280016 280017
Access
Panel
 542CB 642CB
Manpower
TOTAL MANHOURS
 11.00
ELAPSED TIME (HOURS)
 7.00
**CONF 002
Zone
147 148 542 642
Modified FIN
280014 280015 280016 280017 280022 280023
Access
Panel
 147AZ 148AZ 542CB 642CB
Manpower
TOTAL MANHOURS
 15.00
ELAPSED TIME (HOURS)
 9.00
**CONF ALL
A. GENERAL
**CONF 001
(1) Subtask 280092-910-401-001 - Standard Practices
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
06-21-53, Page Block 001
06-21-57, Page Block 001
20-21-12, Page Block 001
28-00-00, Page Block 301
28-10-00, Page Block 301
Consumable Material List (CML)
(a) For the identification of access panels, refer to AMM 06-21-57, Page Block 001 and
AMM 06-21-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-21-00, Page Block 001.
(c) Obey the safety procedures when you do work in a fuel tank, refer to AMM
28-10-00, Page Block 301 and AMM 28-00-00, Page Block 301.
(d) For the specification of materials (Mat. No.) that you must use in this Service
Bulletin, refer to Consumable Material List (CML).
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 16
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 27

@A300
SERVICE BULLETIN
(e) To torque tighten the standard threaded fasteners, refer to AMM 20-21-12, Page
Block 001.
(f) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.
(g) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.
(2) Subtask 280092-839-401-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
**CONF 002
(1) Subtask 280092-910-401-001 - Standard Practices
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
06-21-53, Page Block 001
06-21-57, Page Block 001
20-21-12, Page Block 001
28-00-00, Page Block 301
28-10-00, Page Block 301
Consumable Material List (CML)
(a) For the identification of access panels, refer to AMM 06-21-57, Page Block 001 and
AMM 06-21-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-21-00, Page Block 001.
(c) Obey the safety procedures when you do work in a fuel tank, refer to AMM
28-10-00, Page Block 301 and AMM 28-00-00, Page Block 301.
(d) For the specification of materials (Mat. No.) that you must use in this Service
Bulletin, refer to Consumable Material List (CML).
(e) To torque tighten the standard threaded fasteners, refer to AMM 20-21-12, Page
Block 001.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 17
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 28

@A300
SERVICE BULLETIN
(f) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.
(g) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.
(2) Subtask 280092-839-401-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
**CONF ALL
B. PREPARATION
**CONF 001
(1) Subtask 280092-941-401-001 - Job Set-Up
Work Zones and Access Panels
Zone
 Access/Work location
542
 Access
 Panel 542CB
642
 Access
 Panel 642CB
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
28-10-00, Page Block 301
28-11-14, Page Block 401
WARNING
: YOU MUST OBEY ALL THE SAFETY PROCEDURES WHEN YOU DO
WORK IN OR NEAR A FUEL TANK. IF YOU DO NOT OBEY THE
SAFETY PROCEDURES, THERE IS A RISK OF:
- DEATH OR INJURY TO PERSONS
- DAMAGE TO THE AIRCRAFT OR TO OTHER EQUIPMENT.
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 18
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 29

@A300
SERVICE BULLETIN
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Prepare the aircraft as specified in AMM Task ’STORAGE - SERVICING (Fuel
Tank Draining, Venting and Entry)’, refer to
 AMM 28-10-00, Page Block 301.
1
 Before you go into a fuel tank you must complete the Pre-Entry Checklist,
refer to
 AMM 28-10-00, Page Block 301.
(b) Put platforms in position to get access to these zones, refer to
 AMM 06-21-00,
Page Block 001:
1
 Wing tanks inner - Zones 542 LH (642 RH), refer to
 AMM 28-11-14, Page
Block 401.
(c) Remove the manhole covers:
1
 Wing tanks inner 542CB and 642CB, refer to
 AMM 28-11-14, Page Block 401.
**CONF 002
(1) Subtask 280092-941-401-002 - Job Set-Up
Work Zones and Access Panels
Zone
 Access/Work location
542
 Access
 Panel 542CB
642
 Access
 Panel 642CB
147
 Access
 Panel 147AZ
148
 Access
 Panel 148AZ
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
28-10-00, Page Block 301
28-11-14, Page Block 401
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 19
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 30

@A300
SERVICE BULLETIN
WARNING
: YOU MUST OBEY ALL THE SAFETY PROCEDURES WHEN YOU DO
WORK IN OR NEAR A FUEL TANK. IF YOU DO NOT OBEY THE
SAFETY PROCEDURES, THERE IS A RISK OF:
- DEATH OR INJURY TO PERSONS
- DAMAGE TO THE AIRCRAFT OR TO OTHER EQUIPMENT.
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Prepare the aircraft as specified in AMM Task ’STORAGE - SERVICING (Fuel
Tank Draining, Venting and Entry)’, refer to
 AMM 28-10-00, Page Block 301.
1
 Before you go into a fuel tank you must complete the Pre-Entry Checklist,
refer to
 AMM 28-10-00, Page Block 301.
(b) Put platforms in position to get access to these zones, refer to
 AMM 06-21-00,
Page Block 001:
1
 Wing tanks inner - Zones 542 LH (642 RH), refer to
 AMM 28-11-14, Page
Block 401.
2
 Center tank (if fitted) - Zones 141 and 142, refer to
 AMM 28-11-14, Page
Block 401.
(c) Remove these manhole covers:
1
 Wing tanks inner 542CB and 642CB, refer to
 AMM 28-11-14, Page Block 401.
2
 Center tank 147AZ and 148AZ, refer to
 AMM 28-11-14, Page Block 401.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 20
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 31

@A300
SERVICE BULLETIN
**CONF ALL
C. PROCEDURE
**CONF 001
(1) Subtask 280092-831-401-001 - Replace the Pump Canister Hood Halves
Work Zones and Access Panels
Zone
 Access/Work location
542
 Access
 Panel 542CB
642
 Access
 Panel 642CB
Manpower Resources
Manhours
 8.00
Minimum number of person
 2
Subtask elapsed time
 4.00
Skills
 AIRFRAME
Material necessary to do the job
Equipment BFEB01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
1
 C93-467
 2
 HOOD
2
 MS35206-228
 4
 SCREW
3
 Z4U
 4
 WASHER
5
 C93-463
 2
 SCREW
NOTE
: One Kit is required for each Wing Inner Tank Fuel Pump Canister.
NOTE
: To order Kit BFEB01 from the Vendor quote kit ref. KC93-465-1.
NOTE
: PN G704900 is an acceptable alternative to MS35206-228.
Consumable CMLB01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Solvent
 08BBH1
 As required
Lint-Free Cotton Cloth
 14SBA1
 As required
References
Fig. A-UBAAA
Removal and Installation of the Hood
Halves from the Wing Inner Tank
Canister Pumps
Sheet 01
Sheet 02
NOTE
: This procedure is applicable to each affected pump canister.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 21
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 32

@A300
SERVICE BULLETIN
(a) Remove the hood halves, from the pump canisters (FIN 280014 and FIN 280016
(LH), and FIN 280015 and FIN 280017 (RH)), in the wing inner tank, as follows:
Refer to Fig. A-UBAAA Sheet 01
 .
1
 Clean the surface area of the fuel pump canister. Use:
Lint-Free Cotton
Cloth
14SBA1 As required
made moist with:
Solvent 08BBH1 As required
2
 Remove:
6 Screw MS35206-228 Item (2) Discard
6 Washer AN935-6L Item (3) Discard
2 Hood Half 205481 Item (1) Discard
NOTE
: Make sure that the canister hood halves (and fasteners) are
removed from the fuel tank in their entirety. If any fragment of
a canister hood is found to be missing, make sure that it is
removed from the fuel tank.
(b) Clean the pump mesh filter. Use:
Lint-Free Cotton
Cloth
14SBA1 As required
made moist with:
Solvent 08BBH1 As required
(c) Visually inspect the pump mesh filter for signs of holes and a satisfactory weld
where it attaches to the top land. If any damage is found, replace mesh.
(d) Install the new hood halves, on the pump canisters (FIN 280014 and FIN 280016
(LH), and FIN 280015 and FIN 280017 (RH)), in the wing inner tank, as follows:
Refer to Fig. A-UBAAA Sheet 02
 .
1
 Install:
2 Hood Half C93-467 Item 1
Use:
4 Screw MS35206-228
 Item 2
2 Stepped Screw
Assembly
C93-463 Item 5
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 22
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 33

@A300
SERVICE BULLETIN
4 Washer Z4U Item 3
Make sure that the clearance between the two Hood Halves, item 1, are the
same after installation, refer to Fig. A-UBAAA Sheet 02
 .
2
 Torque the Screw, Item 2 and the Stepped Screw Assembly, Item 5, to 0.2
m.daN (1.47 lbf ft).
(2) Subtask 280092-930-401-001 - Re-Identification
Manpower Resources
Manhours
 1.00
Minimum number of person
 1
Subtask elapsed time
 1.00
Skills
 AIRFRAME
Material necessary to do the job
Reidentified part set REIDB01
ITEM
 NEW PART N˚
 KEYWORD
 ITEM
 OLD PART N˚
 SEE
NOTES
2052C11-5
 CANISTER
 2052C11
2052C12-5
 CANISTER
 2052C12
References
Process and Material Specification
(PMS)
Process and Material Specification (PMS)
01-06-12
(a) Re-identify the fuel pump canisters, in the wing inner tank:
4 Fuel Pump Canister 2052C11
becomes:
4 Fuel Pump Canister 2052C11-5
or:
4 Fuel Pump Canister 2052C12
becomes:
4 Fuel Pump Canister 2052C12-5
Refer to
 PMS 01-06-12.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 23
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 34

@A300
SERVICE BULLETIN
**CONF 002
(1) Subtask 280092-831-401-002 - Replace the Pump Canister Hood Halves
Work Zones and Access Panels
Zone
 Access/Work location
542
 Access
 Panel 542CB
642
 Access
 Panel 642CB
147
 Access
 Panel 147AZ
148
 Access
 Panel 148AZ
Manpower Resources
Manhours
 12.00
Minimum number of person
 2
Subtask elapsed time
 6.00
Skills
 AIRFRAME
Material necessary to do the job
Equipment BFEB01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
1
 C93-467
 2
 HOOD
2
 MS35206-228
 4
 SCREW
3
 Z4U
 4
 WASHER
5
 C93-463
 2
 SCREW
NOTE
: One Kit is required for each Wing Inner Tank Fuel Pump Canister.
NOTE
: To order Kit BFEB01 from the Vendor quote kit ref. KC93-465-1.
NOTE
: PN G704900 is an acceptable alternative to MS35206-228.
Equipment BFEB02
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
1
 C93-467
 2
 HOOD
2
 MS35206-228
 4
 SCREW
3
 Z4U
 4
 WASHER
5
 C93-463
 2
 SCREW
NOTE
: One Kit is required for each Center Tank Fuel Pump Canister.
NOTE
: To order Kit BFEB02 from the Vendor quote kit ref. KC93-465-1.
NOTE
: PN G704900 is an acceptable alternative to MS35206-228.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 24
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 35

@A300
SERVICE BULLETIN
Consumable CMLB01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Solvent
 08BBH1
 As required
Lint-Free Cotton Cloth
 14SBA1
 As required
References
Fig. A-UCAAA
Removal and Installation of the Hood
Halves from the Center Tank Canister
Pumps
Sheet 01
Sheet 02
NOTE
: This procedure is applicable to each affected pump canister.
(a) Remove the hood halves, from the pump canisters (FIN 280014 and FIN 280016
(LH), and FIN 280015 and FIN 280017 (RH)), in the wing inner tank, as follows:
Refer to Fig. A-UCAAA Sheet 01
 .
1
 Clean the surface area of the fuel pump canister. Use:
Lint-Free Cotton
Cloth
14SBA1 As required
made moist with:
Solvent 08BBH1 As required
2
 Remove:
6 Screw MS35206-228 Item (2) Discard
6 Washer AN935-6L Item (3) Discard
2 Hood Half 205481 Item (1) Discard
NOTE
: Make sure that the canister hood halves (and fasteners) are
removed from the fuel tank in their entirety. If any fragment of
a canister hood is found to be missing, make sure that it is
removed from the fuel tank.
(b) Clean the pump mesh filter. Use:
Lint-Free Cotton
Cloth
14SBA1 As required
made moist with:
Solvent 08BBH1 As required
(c) Visually inspect the pump mesh filter for signs of holes and a satisfactory weld
where it attaches to the top land. If any damage is found, replace mesh.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 25
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 36

@A300
SERVICE BULLETIN
(d) Install the new hood halves, on the pump canisters (FIN 280014 and FIN 280016
(LH), and FIN 280015 and FIN 280017 (RH)), in the wing inner tank, as follows:
Refer to Fig. A-UCAAA Sheet 02
 .
1
 Install:
2 Hood Half C93-467 Item 1
Use:
4 Screw MS35206-228
 Item 2
2 Stepped Screw
Assembly
C93-463 Item 5
4 Washer Z4U Item 3
Make sure that the clearance between the two Hood Halves, item 1, are the
same after installation, refer to Fig. A-UCAAA Sheet 02
2
 Torque the Screw, Item 2 and the Stepped Screw Assembly, Item 5, to 0.2
m.daN (1.47 lbf ft).
(e) Remove the hood halves, from the pump canisters (FIN 280022 (LH) and FIN
280023 (RH)), in the center tank, as follows:
Refer to Fig. A-UCAAA Sheet 01
 .
1
 Clean the surface area of the fuel pump canister. Use:
Lint-Free Cotton
Cloth
14SBA1 As required
made moist with:
Solvent 08BBH1 As required
2
 Remove:
6 Screw MS35206-228 Item (2) Discard
6 Washer AN935-6L Item (3) Discard
2 Hood Half 3C93-129 Item (4) Discard
NOTE
: Make sure that the canister hood halves (and fasteners) are
removed from the fuel tank in their entirety. If any fragment of
a canister hood is found to be missing, make sure that it is
removed from the fuel tank.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 26
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 37

@A300
SERVICE BULLETIN
(f) Clean the pump mesh filter. Use:
Lint-Free Cotton
Cloth
14SBA1 As required
made moist with:
Solvent 08BBH1 As required
(g) Visually inspect the pump mesh filter for signs of holes and a satisfactory weld
where it attaches to the top land. If any damage is found, replace mesh.
(h) Install the hood halves, on the pump canisters (FIN 280022 (LH) and FIN 280023
(RH)), in the center tank, as follows:
Refer to Fig. A-UCAAA Sheet 02
 .
1
 Install:
2 Hood Half C93-467 Item 1
Use:
4 Screw MS35206-228
 Item 2
2 Stepped Screw
Assembly
C93-463 Item 5
4 Washer Z4U Item 3
Make sure that the clearance between the two Hood Halves, item 1, are the
same after installation, refer to Fig. A-UCAAA Sheet 02
 .
2
 Torque the Screw, Item 2 and the Stepped Screw Assembly, Item 5, to 0.2
m.daN (1.47 lbf ft).
(2) Subtask 280092-930-401-002 - Re-Identification
Manpower Resources
Manhours
 1.00
Minimum number of person
 1
Subtask elapsed time
 1.00
Skills
 AIRFRAME
Material necessary to do the job
Reidentified part set REIDB02
ITEM
 NEW PART N˚
 KEYWORD
 ITEM
 OLD PART N˚
 SEE
NOTES
2052C11-5
 CANISTER
 2052C11
2052C12-5
 CANISTER
 2052C12
C93R51-601-5
 CANISTER
 C93R51-601
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 27
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 38

@A300
SERVICE BULLETIN
References
Process and Material Specification
(PMS)
Process and Material Specification (PMS)
01-06-12
(a) Re-identify the fuel pump canisters, in the wing inner tank:
4 Fuel Pump Canister 2052C11
becomes:
4 Fuel Pump Canister 2052C11-5
or:
4 Fuel Pump Canister 2052C12
becomes:
4 Fuel Pump Canister 2052C12-5
Refer to
 PMS 01-06-12.
(b) Re-identify the fuel pump canister, in the center tank:
2 Fuel Pump Canister C93R51-601
becomes:
2 Fuel Pump Canister C93R51-601-5
Refer to
 PMS 01-06-12.
**CONF ALL
D. TEST
**CONF 001
(1) Subtask 280092-700-401-001 - Testing
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 28-11-14, Page Block 401
(a) The test procedure is included in the "Close-Up" for "Installation of the manhole
covers", refer to
 AMM 28-11-14, Page Block 401.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 28
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 39

@A300
SERVICE BULLETIN
**CONF 002
(1) Subtask 280092-700-401-001 - Testing
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 28-11-14, Page Block 401
(a) The test procedure is included in the "Close-Up" for "Installation of the manhole
covers", refer to
 AMM 28-11-14, Page Block 401.
**CONF ALL
E. CLOSE-UP
**CONF 001
(1) Subtask 280092-942-401-001 - Close-Up
Work Zones and Access Panels
Zone
 Access/Work location
542
 Access
 Panel 542CB
642
 Access
 Panel 642CB
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 28-11-14, Page Block 401
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the manhole covers:
1
 On the inner wing tanks install: 542CB and 642CB, refer to
 AMM 28-11-14,
Page Block 401.
(c) Remove the access platforms.
(d) Put the aircraft back to its initial configuration.
**CONF 002
(1) Subtask 280092-942-401-002 - Close-Up
Work Zones and Access Panels
Zone
 Access/Work location
542
 Access
 Panel 542CB
642
 Access
 Panel 642CB
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 29
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 40

@A300
SERVICE BULLETIN
147
 Access
 Panel 147AZ
148
 Access
 Panel 148AZ
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 28-11-14, Page Block 401
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install these manhole covers:
1
 On the inner wing tanks install: 542CB and 642CB, refer to
 AMM 28-11-14,
Page Block 401.
2
 On the center tank install: 147AZ and 148AZ, refer to
 AMM 28-11-14, Page
Block 401.
(c) Remove the access platforms.
(d) Put the aircraft back to its initial configuration.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 30
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 41

@A300
SERVICE BULLETIN
Task 280092-831-896-001 - Modification for aircra ft that have accomplished this Service
Bulletin at Rev 00 - ADDITIONAL WORK
**CONF ALL
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
WARNING
: THIS INSTRUCTION IS APPLICABLE TO A CRITICAL DESIGN
CONFIGURATION CONTROL LIMITAT ION (CDCCL). CAREFULLY OBEY ALL
GIVEN INSTRUCTIONS WHEN YOU DO THIS STEP. IF YOU DO NOT OBEY
THESE INSTRUCTIONS, A DANGEROU S CONDITION CAN OCCUR THAT CAN
CAUSE A POSSIBLE FUEL TANK EXPLOSION.
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC; AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
Task Associated Data
**CONF 001
Zone
542
 642
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 31
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 42

@A300
SERVICE BULLETIN
Modified FIN
280014
 280015
 280016
 280017
Access
Panel
 542CB
 642CB
Manpower
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 5.00
**CONF 002
Zone
147
 148
 542
 642
Modified FIN
280014
 280015
 280016
 280017
 280022
 280023
Access
Panel
 147AZ
 148AZ
 542CB
 642CB
Manpower
TOTAL MANHOURS
 9.00
ELAPSED TIME (HOURS)
 6.00
**CONF
 ALL
A. GENERAL
**CONF 001
(1) Subtask 280092-910-402-001 - Standard Practices
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
06-21-53, Page Block 001
06-21-57, Page Block 001
20-21-12, Page Block 001
28-00-00, Page Block 301
28-10-00, Page Block 301
Consumable Material List (CML)
(a) For the identification of access panels, refer to AMM 06-21-57, Page Block 001 and
AMM 06-21-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-21-00, Page Block 001.
(c) Obey the safety procedures when you do work in a fuel tank, refer to AMM
28-10-00, Page Block 301 and AMM 28-00-00, Page Block 301.
(d) For the specification of materials (Mat. No.) that you must use in this Service
Bulletin, refer to Consumable Material List (CML).
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 32
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 43

@A300
SERVICE BULLETIN
(e) To torque tighten the standard threaded fasteners, refer to AMM 20-21-12, Page
Block 001.
(f) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.
(g) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.
(2) Subtask 280092-839-402-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
**CONF 002
(1) Subtask 280092-910-402-001 - Standard Practices
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
06-21-53, Page Block 001
06-21-57, Page Block 001
20-21-12, Page Block 001
28-00-00, Page Block 301
28-10-00, Page Block 301
Consumable Material List (CML)
(a) For the identification of access panels, refer to AMM 06-21-57, Page Block 001 and
AMM 06-21-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-21-00, Page Block 001.
(c) Obey the safety procedures when you do work in a fuel tank, refer to AMM
28-10-00, Page Block 301 and AMM 28-00-00, Page Block 301.
(d) For the specification of materials (Mat. No.) that you must use in this Service
Bulletin, refer to Consumable Material List (CML).
(e) To torque tighten the standard threaded fasteners, refer to AMM 20-21-12, Page
Block 001.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 33
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 44

@A300
SERVICE BULLETIN
(f) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.
(g) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.
(2) Subtask 280092-839-402-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
**CONF
 ALL
B. PREPARATION
**CONF 001
(1) Subtask 280092-941-402-001 - Job Set-up
Work Zones and Access Panels
Zone
 Access/Work location
542
 Access
 Panel 542CB
642
 Access
 Panel 642CB
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
28-10-00, Page Block 301
28-11-14, Page Block 401
WARNING
: YOU MUST OBEY ALL THE SAFETY PROCEDURES WHEN YOU DO
WORK IN OR NEAR A FUEL TANK. IF YOU DO NOT OBEY THE
SAFETY PROCEDURES, THERE IS A RISK OF:
- DEATH OR INJURY TO PERSONS
- DAMAGE TO THE AIRCRAFT OR TO OTHER EQUIPMENT.
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 34
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 45

@A300
SERVICE BULLETIN
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Prepare the aircraft as specified in AMM Task ’STORAGE - SERVICING (Fuel
Tank Draining, Venting and Entry)’, refer to AMM 28-10-00, Page Block 301.
1
 Before you go into a fuel tank you must complete the Pre-Entry Checklist,
refer to AMM 28-10-00, Page Block 301.
(b) Put platforms in position to get access to these zones, refer to AMM 06-21-00,
Page Block 001:
1
 Wing tanks inner - Zones 542 LH (642 RH), refer to AMM 28-11-14, Page
Block 401.
(c) Remove the manhole covers:
1
 Wing tanks inner 542CB and 642CB, refer to AMM 28-11-14, Page Block 401.
**CONF 002
(1) Subtask 280092-941-402-002 - Job Set-up
Work Zones and Access Panels
Zone
 Access/Work location
542
 Access
 Panel 542CB
642
 Access
 Panel 642CB
147
 Access
 Panel 147AZ
148
 Access
 Panel 148AZ
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
28-10-00, Page Block 301
28-11-14, Page Block 401
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 35
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 46

@A300
SERVICE BULLETIN
WARNING
: YOU MUST OBEY ALL THE SAFETY PROCEDURES WHEN YOU DO
WORK IN OR NEAR A FUEL TANK. IF YOU DO NOT OBEY THE
SAFETY PROCEDURES, THERE IS A RISK OF:
- DEATH OR INJURY TO PERSONS
- DAMAGE TO THE AIRCRAFT OR TO OTHER EQUIPMENT.
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Prepare the aircraft as specified in AMM Task ’STORAGE - SERVICING (Fuel
Tank Draining, Venting and Entry)’, refer to AMM 28-10-00, Page Block 301.
1
 Before you go into a fuel tank you must complete the Pre-Entry Checklist,
refer to AMM 28-10-00, Page Block 301.
(b) Put platforms in position to get access to these zones, refer to AMM 06-21-00,
Page Block 001:
1
 Wing tanks inner - Zones 542 LH (642 RH), refer to AMM 28-11-14, Page
Block 401.
2
 Center tank (if fitted) - Zones 141 and 142, refer to AMM 28-11-14, Page
Block 401.
(c) Remove these manhole covers:
1
 Wing tanks inner 542CB and 642CB, refer to AMM 28-11-14, Page Block 401.
2
 Center tank 147AZ and 148AZ, refer to AMM 28-11-14, Page Block 401.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 36
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 47

@A300
SERVICE BULLETIN
**CONF
 ALL
C. PROCEDURE
**CONF 001
(1) Subtask 280092-831-402-001 - Replace the Outer Attachment Screws of the Fuel
Pump Canister Hood Halves
Work Zones and Access Panels
Zone
 Access/Work location
542
 Access
 Panel 542CB
642
 Access
 Panel 642CB
Manpower Resources
Manhours
 4.00
Minimum number of person
 2
Subtask elapsed time
 2.00
Skills
 AIRFRAME
Material necessary to do the job
Equipment BFEB01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
2
 MS35206-228
 4
 SCREW
NOTE
: One Kit is required for each Wing Inner Tank Fuel Pump Canister.
NOTE
: To order Kit BFEB01 from the Vendor quote kit ref. KC93-465-1.
NOTE
: PN G704900 is an acceptable alternative to MS35206-228.
References
Fig. A-UBAAA
Removal and Installation of the Hood
Halves from the Wing Inner Tank
Canister Pumps
Sheet
 01
Sheet
 02
NOTE
: This procedure is applicable to each affected pump canister.
(a) Remove the hood half fasteners from the pump canisters (FIN 280014 and FIN
280016 (LH), and FIN 280015 and FIN 280017 (RH)), in the wing inner tank, as
follows:
Refer to Fig. A-UBAAA Sheet 01
 .
1
 Remove:
4
 Screw
 CV0003
 Item (2
) Discard
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 37
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 48

@A300
SERVICE BULLETIN
4
 Washer
 Z4U
 Item (3
) Retain
NOTE
: Make sure that the canister hood fasteners are removed from
the fuel tank.
(b) Install the new hood half fasteners on the pump canisters (FIN 280014 and FIN
280016 (LH), and FIN 280015 and FIN 280017 (RH)), in the wing inner tank, as
follows:
Refer to Fig. A-UBAAA Sheet 02
 .
1
 Install:
4
 Screw
 MS35206-228
 Item 2
4
 Washer
 Z4U
 Item (3
) Retained at
removal
Make sure that the clearance between the two Hood Halves, item 1, are the
same after installation of the fasteners, refer to Fig. A-UBAAA Sheet 02
 .
2
 Torque the Screw, Item 2, to 0.2 m.daN (1.47 lbf ft).
(2) Subtask 280092-930-402-001 - Re-identification
Work Zones and Access Panels
Zone
 Access/Work location
542
642
Manpower Resources
Manhours
 1.00
Minimum number of person
 1
Subtask elapsed time
 1.00
Skills
 AIRFRAME
Material necessary to do the job
Reidentified part set REIDB03
ITEM
 NEW PART N˚
 KEYWORD
 ITEM
 OLD PART N˚
 SEE
NOTES
2052C11-5
 CANISTER
 2052C11-4
2052C12-5
 CANISTER
 2052C12-4
NOTE
: Matset REIDB03 is required by aircraft in Config. 001 to accomplish the
Additional Work.
References
Process and Material Specification
(PMS)
Process and Material Specification (PMS)
01-06-12
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 38
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 49

@A300
SERVICE BULLETIN
(a) Re-identify the fuel pump canisters in the inner wing tank:
4
 Fuel Pump Canister
 2052C11-4
becomes:
4
 Fuel Pump Canister
 2052C11-5
or:
4
 Fuel Pump Canister
 2052C12-4
becomes:
4
 Fuel Pump Canister
 2052C12-5
Refer to Process and Material Specification (PMS) 01-06-12.
**CONF 002
(1) Subtask 280092-831-402-002 - Replace the Outer Attachment Screws of the Fuel
Pump Canister Hood Halves
Work Zones and Access Panels
Zone
 Access/Work location
542
 Access
 Panel 542CB
642
 Access
 Panel 642CB
147
 Access
 Panel 147AZ
148
 Access
 Panel 148AZ
Manpower Resources
Manhours
 6.00
Minimum number of person
 2
Subtask elapsed time
 3.00
Skills
 AIRFRAME
Material necessary to do the job
Equipment BFEB02
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
2
 MS35206-228
 4
 SCREW
NOTE
: One Kit is required for each Center Tank Fuel Pump Canister.
NOTE
: To order Kit BFEB02 from the Vendor quote kit ref. KC93-465-1.
NOTE
: PN G704900 is an acceptable alternative to MS35206-228.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 39
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 50

@A300
SERVICE BULLETIN
References
Fig. A-UCAAA
Removal and Installation of the Hood
Halves from the Center Tank Canister
Pumps
Sheet
 01
Sheet
 02
NOTE
: This procedure is applicable to each affected pump canister.
(a) Remove the hood half fasteners from the pump canisters (FIN 280014 and FIN
280016 (LH), and FIN 280015 and FIN 280017 (RH)), in the wing inner tank, as
follows:
Refer to Fig. A-UCAAA Sheet 01
 .
1
 Remove:
4
 Screw
 CV0003
 Item (2
) Discard
4
 Washer
 Z4U
 Item (3
) Retain
NOTE
: Make sure that the canister hood fasteners are removed from
the fuel tank.
(b) Install the new hood half fasteners on the pump canisters (FIN 280014 and FIN
280016 (LH), and FIN 280015 and FIN 280017 (RH)), in the wing inner tank, as
follows:
Refer to Fig. A-UCAAA Sheet 02
 .
1
 Install:
4
 Screw
 MS35206-228
 Item 2
4
 Washer
 Z4U
 Item (3
) Retained at
removal
Make sure that the clearance between the two Hood Halves, item 1, are the
same after installation of the fasteners, refer to Fig. A-UCAAA Sheet 02
 .
2
 Torque the Screw, Item 2, to 0.2 m.daN (1.47 lbf ft).
(c) Remove the hood half fasteners, from the pump canisters (FIN 280022 (LH) and
FIN 280023 (RH)), in the center tank, as follows:
Refer to Fig. A-UCAAA Sheet 01
 .
1
 Remove:
4
 Screw
 CV0003
 Item (2
) Discard
4
 Washer
 Z4U
 Item (3
) Retain
NOTE
: Make sure that the canister hood half fasteners are removed
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 40
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 51

@A300
SERVICE BULLETIN
from the fuel tank.
(d) Install the hood half fasteners on the pump canisters (FIN 280022 (LH) and FIN
280023 (RH)), in the center tank, as follows:
Refer to Fig. A-UCAAA Sheet 02
 .
1
 Install:
4
 Screw
 MS35206-228
 Item 2
4
 Washer
 Z4U
 Item (3
) Retained at
removal
Make sure that the clearance between the two Hood Halves, item 1, are the
same after installation, refer to Fig. A-UCAAA Sheet 02
 .
2
 Torque the Screw, Item 2, to 0.2 m.daN (1.47 lbf ft).
(2) Subtask 280092-930-402-002 - Re-identification
Work Zones and Access Panels
Zone
 Access/Work location
542
642
147
148
Manpower Resources
Manhours
 1.00
Minimum number of person
 1
Subtask elapsed time
 1.00
Skills
 AIRFRAME
Material necessary to do the job
Reidentified part set REIDB04
ITEM
 NEW PART N˚
 KEYWORD
 ITEM
 OLD PART N˚
 SEE
NOTES
2052C11-5
 CANISTER
 2052C11-4
2052C12-5
 CANISTER
 2052C12-4
C93R51-601-5
 CANISTER
 C93R51-601-4
NOTE
: Matset REIDB04 is required by aircraft in Config. 002 to accomplish the
Additional Work.
References
Process and Material Specification
(PMS)
Process and Material Specification (PMS)
01-06-12
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 41
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 52

@A300
SERVICE BULLETIN
(a) Re-identify the fuel pump canisters in the inner wing tank:
4
 Fuel Pump Canister
 2052C11-4
becomes:
4
 Fuel Pump Canister
 2052C11-5
or:
4
 Fuel Pump Canister
 2052C12-4
becomes:
4
 Fuel Pump Canister
 2052C12-5
Refer to Process and Material Specification (PMS) 01-06-12.
(b) Re-identify the fuel pump canisters in the center tank:
2
 Fuel Pump Canister
 C93R51-601-4
becomes:
2
 Fuel Pump Canister
 C93R51-601-5
Refer to Process and Material Specification (PMS) 01-06-12.
**CONF
 ALL
D. TEST
**CONF 001
(1) Subtask 280092-700-402-001 - Testing
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 28-11-14, Page Block 401
(a) The test procedure is included in the "Close-Up" for "Installation of the manhole
covers", refer to AMM 28-11-14, Page Block 401.
**CONF 002
(1) Subtask 280092-700-402-001 - Testing
Manpower Resources
Skills
 AIRFRAME
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 42
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 53

@A300
SERVICE BULLETIN
References
Aircraft Maintenance Manual (AMM)
 28-11-14, Page Block 401
(a) The test procedure is included in the "Close-Up" for "Installation of the manhole
covers", refer to AMM 28-11-14, Page Block 401.
**CONF
 ALL
E. CLOSE-UP
**CONF 001
(1) Subtask 280092-942-402-001 - Close-up
Work Zones and Access Panels
Zone
 Access/Work location
542
 Access
 Panel 542CB
642
 Access
 Panel 642CB
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 28-11-14, Page Block 401
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the manhole covers:
1
 On the inner wing tanks install: 542CB and 642CB, refer to AMM 28-11-14,
Page Block 401.
(c) Remove the access platforms.
(d) Put the aircraft back to its initial configuration.
**CONF 002
(1) Subtask 280092-942-402-002 - Close-up
Work Zones and Access Panels
Zone
 Access/Work location
542
 Access
 Panel 542CB
642
 Access
 Panel 642CB
147
 Access
 Panel 147AZ
148
 Access
 Panel 148AZ
Manpower Resources
Skills
 AIRFRAME
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 43
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 54

@A300
SERVICE BULLETIN
References
Aircraft Maintenance Manual (AMM)
 28-11-14, Page Block 401
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install these manhole covers:
1
 On the inner wing tanks install: 542CB and 642CB, refer to AMM 28-11-14,
Page Block 401.
2
 On the center tank install: 147AZ and 148AZ, refer to AMM 28-11-14, Page
Block 401.
(c) Remove the access platforms.
(d) Put the aircraft back to its initial configuration.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 44
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 55

@A300
SERVICE BULLETIN
**CONF 001
BEFORE
TYPICAL
HOOD HALF
FILTER
FUEL PUMP
CANISTER
HOOD HALF
TYPICAL
C
RIB2
LH WING SHOWN
RH WING SIMILAR
Z542 (Z642)
A
B
B
C
C(2)
(3)
(2)
(3)
(2)
(3)
(4)
D
(1)
A_SB_280092_7_BAAA_01_00
A
A
Figure A-UBAAA - Sheet 01
Removal and Installation of the Hood Halves from the Wing Inner Tank Canister Pumps
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 45
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 56

@A300
SERVICE BULLETIN
**CONF 001
TYPICAL
MAINTAIN A
CLEARANCE HERE
A
A
A A
AFTER
TYPICAL
HOOD HALF
FILTER
FUEL PUMP
CANISTER
HOOD HALF
D
E
E
E
2
3
3
2
5
1
5
4
1
NOTE:
MAKE SURE THAT THE CLEARANCE IS EQUAL BETWEEN THE HOOD HALVES.01
01
01
A_SB_280092_7_BAAA_02_01
Figure A-UBAAA - Sheet 02
Removal and Installation of the Hood Halves from the Wing Inner Tank Canister Pumps
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 46
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 57

@A300
SERVICE BULLETIN
**CONF 002
BEFORE
TYPICAL
HOOD HALF
FILTER
FUEL PUMP
CANISTER
HOOD HALF
TYPICAL
FR46
FR47
A
(2)
(3)
(2)
(3)
(2)
(3)
(4)
(1)
D
C
E
D
D
C
C
A B
 − Z142Z141
B
RIB2
LH WING SHOWN
RH WING SIMILAR
Z542 (Z642)
B
C
A_SB_280092_7_CAAA_01_01
Figure A-UCAAA - Sheet 01
Removal and Installation of the Hood Halves from the Center Tank Canister Pumps
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 47
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 58

@A300
SERVICE BULLETIN
**CONF 002
TYPICAL
MAINTAIN A
CLEARANCE HERE
A
A
A A
AFTER
TYPICAL
HOOD HALF
FILTER
FUEL PUMP
CANISTER
HOOD HALF
2
3
3
2
5
1
5
4
1
NOTE:
MAKE SURE THAT THE CLEARANCE IS EQUAL BETWEEN THE HOOD HALVES.01
01
01
F
E
F
F
A_SB_280092_7_CAAA_02_02
Figure A-UCAAA - Sheet 02
Removal and Installation of the Hood Halves from the Center Tank Canister Pumps
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 48
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 59

@A300
SERVICE BULLETIN
Appendix 01 - Elapsed Time Assumption
**CONF ALL
For an explanation of the manhours and elapsed time, refer to the Gantt Chart given in Appendix 01.
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 60

@A300
SERVICE BULLETIN
Appendix 01 - Elapsed Time Assumption
**CONF 001
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No. A300−28−0092
GET ACCESS
MH ET/S
TOTAL MANHOURS
SB ELAPSED TIME
11.00
7.00
STEPS
1.00 1.00
0
REPLACE THE PUMP 8.00 4.00
CLOSE−UP 1.00 1.00
MH
ET/S:
PER
MANHOURS
ELAPSED TIME PER STEP
NUMBER OF PERSONS
01
02
THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
01
02
NOTES:
PER
1
2
1
:
:
SB ELAPSED TIME
(HOURS)
2
IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
ARE NOT REFLECTED IN THIS GANTT CHART.
RE−IDENTIFICATION 1.00 1.00 1
CANISTER HOOD HALVES
A_SB_280092_7_AAAA_01_00
468 10
Figure A-UAAAA - Sheet 01
Elapsed Time Assumption
DATE: Dec 12/13 SERVICE BULLETIN No.: A300-28-0092
REVISION No.: 01 - Aug 29/14 Page: 2
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

The text continues at https://openairdocs.org/service-documents/airbus/sb-28-0092/file/7fb52722a034.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
