# Apical Alert Service Bulletin 2010-03: Revision C

- Rights: © Apical Industries, Inc. Filed by the FAA in regulations.gov docket FAA-2013-0481; AD 2013-22-21 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Apical Alert Service Bulletin 2010-03](https://openairdocs.org/service-documents/apical/sb-2010-03.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin SB2010-03 Rev C
- Pages: 11
- PDF: https://openairdocs.org/files/sha256/e0/74/e0745a7f96a69e538d34ac80b8f1e4d6ca521282b38a1a1449d8ce8a006548de
- Page: https://openairdocs.org/service-documents/apical/sb-2010-03/file/e0745a7f96a6

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Copyright 2010-2011 Apical Industries, Inc.    Page 1 of 11 
All Rights Reserved 
 
 
2608 TEMPLE HEIGHTS DRIVE 
OCEANSIDE, CALIFORNIA 92056-3512 
PH: (760) 724-5300    FAX: (760) 758-9612 
Website: apicalindustries.com 
 
Alert Service Bulletin  
 
Document Number:  SB2010-03 
 
Date: 12/21/11 
 
Revision: C 
 
Effective Models:  Helicopter Models with Apical Emergency Float Kits approved under 
STC SR01535LA: 
 
Kit P/N Kit Description Kit S/N Effectivity Helicopter Model 
614.3001 Float with Liferafts Kit 096 and below Bell 407 
614.3003 Float with Liferafts Kit 145 and below Bell 206L, L-1, L-3, L-4 
614.3004 Float Kit 011 and below Bell 407 
614.3006 Float Kit 008 and below Bell 206L, L-1, L-3, L-4 
614.3007 Float with Liferafts Kit 015 and below Bell 206A, B 
614.3008 Float Kit 004 and below Bell 206A, B 
               
NOTE 
This bulletin is sent to the operators of record for the model 
aircraft as shown above.  If an aircraft has been leased or 
sold, send this service bulletin to the new operator.

### Page 2

REF. DWG. NO. REPORT 
 614.3000 SB2010-03 
ALERT SERVICE BULLETIN  Rev. C 
  12/21/11 
 
Copyright 2010-2011 Apical Industries, Inc.    Page 2 of 11 
All Rights Reserved 
 
Subject:  Inspection of Port Fitting Hose Routing 
 
Background:  During a recent incident involving a helicopter with the subject STC 
installed, the pilot attempted to deploy the floats as designed.  Although the Inflation 
Valve released the pressurized gas normally, the floats did not deploy evenly, including 
a rupture of the Right Hand Mid Float.   
 
It was determined that the cause for the uneven deployment was incorrect installation of 
the float inflation hoses at the Port Fitting located at the base of the forward crosstube 
saddles.  A subsequent inspection of one operator’s fleet discovered more instances of 
incorrect hose installation. 
 
In order to remedy this, Apical is requiring a mandatory inspection of the float hose Port 
Fitting connection and the installation of a port fitting adapter and a replacement Aft 
Float Hose Assy to prevent the possibility of a future case of improper routing. 
 
Action:  This ASB provides instructions for the inspection of the float inflation hoses, 
the installation of a Port Fitting Adapter on the Port Fitting, and a replacement of the 
hose leading to the Aft Float.   
 
Compliance:  Compliance with Section 1.0 and 2.0 of this ASB shall be within 45 flight 
hours from the date of approval of the ASB. Compliance with Sections 3.0 through 5.0 
shall be accomplished no later than 07/01/12.  If compliance with Section 1.0 and 2.0 
was done previously under an earlier revision of this document, it is not necessary to 
repeat those steps, but reporting this compliance to Apical shall be accomplished. 
Report compliance and the results of the inspection to Lisa Mansfield at Apical 
(lmansfield@apicalindustries.com, (760) 724-5300) for each serial number aircraft 
affected by this ASB. 
 
Manpower:  Compliance should take approximately 1 hour. 
 
Material Information:  There are no special tools required for compliance.  The label 
and shrink tubing referenced in this bulletin can be obtained from commercially 
available sources or from Apical Industries.  The additional components can be sourced 
by referencing the table in Section 6.0.  Please contact Apical at (760) 724-5300 or 
Manny Gonzalez or Lisa Mansfield in sales (mgonzalez@apicalindustries.com or 
lmansfield@apicalindustries.com ).   
 
Weight & Balance:  Accomplishment of this ASB results in no change to the weight of 
the kits shown in the Effective Models section.   
 
Publications Affected:  The Installation Instructions and the Instructions for Continued 
Airworthiness for each kit in the Effective Models section will be revised to reflect the 
inspection procedures specific to the float inflation hoses.

### Page 3

REF. DWG. NO. REPORT 
 614.3000 SB2010-03 
ALERT SERVICE BULLETIN  Rev. C 
  12/21/11 
 
Copyright 2010-2011 Apical Industries, Inc.    Page 3 of 11 
All Rights Reserved 
 
 
Approval:  The resultant modifications described in the Accomplishment Instructions 
have been shown to comply with the applicable Federal Aviation Regulations and have 
been approved by the Los Angeles Certification Office on December 21, 2011. 
 
Accomplishment Instructions: 
 
CAUTION 
 
Prior to working around charged cylinders, make sure that the safety pin is 
installed in the pull cable housing of the Inflation Valve.  Also, make sure that the 
cylinder is secured tightly to the Reservoir Assembly Brackets, if installed on the 
helicopter.  Install a cap plug on all disconnected hoses to prevent debris from 
entering the lines. 
 
1.0 Float Inflation Hose Inspection  
 
1. Reference Figure 1 through Figure  2 for the following instructions. 
 
2. Locate the Port Fittings (F/N 29, 40,  106, or 107) at the LH and RH forward 
crosstube saddles (reference Figure 1).  The Port Fittings should be in good 
condition, free of corrosion, and not bent.  Any instance of corrosion that has 
penetrated the base material more than .010 inches is cause for replacement.  
Any instance of damage that has removed more than .010 inches of base 
material is cause for replacement.  Any bends in the tubing from their original 
position of more than 5 degrees may prevent the Port Fitting Adapter from 
sealing properly.  It is acceptable to carefully bend the port fitting back to its 
originally intended position to enable proper sealing of the Port Fitting Adapter.

### Page 4

REF. DWG. NO. REPORT 
 614.3000 SB2010-03 
ALERT SERVICE BULLETIN  Rev. C 
  12/21/11 
 
Copyright 2010-2011 Apical Industries, Inc.    Page 4 of 11 
All Rights Reserved 
 
  
  
Figure 1:  Port Fitting location 
 
3. Inspect the position of the float infl ation hoses.  The Mid Float inflation hose 
should be connected to the 90 degree bend in the Port Fitting.  The Aft Float 
inflation hose should be connected to the straight portion of the Port Fitting.   
 
 
 
 
Figure 2:  Port Fitting in Good Condition, LH Shown, Typical All Models 
To Mid 
Float 
To Aft 
Float 
To Fwd 
Float 
FWD 
Port Fitting 
Location, RH 
Shown, LH 
Typical

### Page 5

REF. DWG. NO. REPORT 
 614.3000 SB2010-03 
ALERT SERVICE BULLETIN  Rev. C 
  12/21/11 
 
Copyright 2010-2011 Apical Industries, Inc.    Page 5 of 11 
All Rights Reserved 
 
 
2.0 Label Installation (Typical All Models)  
 
1. Refer to Figure 3 and Figure 4 for the following instructions. 
 
2. Make sure that the Port Fitting is cl ean and free of debris.  Install a label with the 
dimensions and wording shown in Figure 3 on the straight portion of the Port 
Fitting as shown in Figure 4.  Cover the label with clear shrink tubing meeting 
M23053/5-108-C or its equivalent.  Apply the shrink tubing by heating uniformly 
until the tubing is completely sealed against the Port Fitting.  If not commercially 
available, the label and shrink tubing can be purchased directly from Apical. 
 
AFT FLOAT
0.75
BLACK LETTERS
0.25
WHITE BACKGROUND
1. MATERIAL: .004 WHITE VINYL RUBBER
  BASED SOLVENT ADHESIVE UV PRINT 1 MIL
  CLEAR OVERLAMINATE ON TOP.
0.09
 
Figure 3:  Label Detail (Apical P/N 601.1764) 
 
 
Figure 4:  Label Installation, LH Shown, Typical RH Side 
 
Parts List for Figure 4 
Find Number Part Number Description Qty  
1 601.1764 Label 2 
2 601.1429 Shrink Tubi ng (M23053/5-108-C) 4” 
 
F/N 1 
F/N 2 
Existing Part 
Marking Label (REF)

### Page 6

REF. DWG. NO. REPORT 
 614.3000 SB2010-03 
ALERT SERVICE BULLETIN  Rev. C 
  12/21/11 
 
Copyright 2010-2011 Apical Industries, Inc.    Page 6 of 11 
All Rights Reserved 
 
 
 
3.0 Float Inflation Hose Removal  
 
1. Disconnect the hose running to t he Aft Float at the Port Fitting. 
 
2. Remove the Aft Float from the skid t ube by unfastening the 3 bolts attaching the 
girt to the skid tube.  Disconnect the hose from the Aft Float that is routed along 
the inboard surface of the skid tube. 
 
3. Disconnect the hose from the skid tube by unfastening the bolts and loop clamps 
attaching the hose to the skid tube as shown in Figure 5. 
 
 
 
Figure 5: Aft Float Hose View of RH Aft Float, Looking Outboard 
 
 
4. The following table shows which Hose Assy part numbers will be removed.  
Discard the removed hoses. 
 
Hose Assemblies Requiring Removal 
Aircraft Type Hose Assy Part Number QTY Per Kit 
206A, B 602.1417 2 
206L, L-1, L-3, L-4 602.1420 2 
407 602.1413 2 
 
Remove hose 
from skid tube 
and Aft float

### Page 7

REF. DWG. NO. REPORT 
 614.3000 SB2010-03 
ALERT SERVICE BULLETIN  Rev. C 
  12/21/11 
 
Copyright 2010-2011 Apical Industries, Inc.    Page 7 of 11 
All Rights Reserved 
 
 
4.0 Port Fitting Adapter Installation  
 
3. Make sure that the sea ling surface of the Port Fitting is clean and free of debris.  
Install a Port Fitting Adapter (P/N 614.8709) onto the straight fitting on the Port 
Fitting as shown in Figure 6.  Torque to 50-60 in-lbs.   
 
 
  
Figure 6:  Port Fitting Adapter Correct Installation (LH Port Fitting Shown, RH 
Typical) 
 
5.0 Aft Hose Installation  
 
1. Attach the new Aft Float Hose to t he Aft float.  Torque fitting to 50-60 in-lbs. 
 
2. Attach the Aft Float to the skid tube us ing the same Bolts and Washers that were 
removed in Section 2.0.  Replace the Nuts with those in the Service Bulletin Kit. 
 
3. Attach the Hose to the Port Fitting A dapter.  The replacement Hose should have 
a male threaded end which interfaces with the female thread on the Port Adapter 
(see Figure 5). 
 
4. Attach the Hose to the inboard edge of  the skid tube using the same hardware 
that was removed in Section 2.0, and picking up the same attachment locations. 
 
Port Fitting Adapter 
(P/N 614.8907) 
FWD

### Page 8

REF. DWG. NO. REPORT 
 614.3000 SB2010-03 
ALERT SERVICE BULLETIN  Rev. C 
  12/21/11 
 
Copyright 2010-2011 Apical Industries, Inc.    Page 8 of 11 
All Rights Reserved 
 
 
Figure 7:  Aft Float Hose Installation 
 
5. Figure 8 through Figure 10 show  the correct float hose routing 
 
 
 
Figure 8:  Bell 407 Port Fitting and Hose Routing, LH shown, RH 
Symmetrical 
 
Parts List for Figure 8 
Find Number Part Number Description Qty  
19 602.1410 Hose Assy 2 
20 602.1411 Hose Assy 2 
29 614.8701 Port Fitting L.H. 1 
35 602.1429 Hose Assy 2 
40 614.8702 Port Fitting R.H. 1 
Ref 602.1409 Hose Assy 2 
Ref 602.1412 Hose Assy 4 
 
To Aft Float

### Page 9

REF. DWG. NO. REPORT 
 614.3000 SB2010-03 
ALERT SERVICE BULLETIN  Rev. C 
  12/21/11 
 
Copyright 2010-2011 Apical Industries, Inc.    Page 9 of 11 
All Rights Reserved 
 
 
 
Figure 9:  Bell 206A & B Port Fitting and Hose Routing, LH shown, RH 
Symmetrical 
 
Parts List for Figure 9 
Find Number Part Number Description Qty  
63 602.1430 Hose Assy 2 
69 602.1415 Hose Assy 2 
70 602.1416 Hose Assy 2 
106 614.8703 Port Fitting L.H. 1 
107 614.8704 Port Fitting R.H. 1 
Ref 602.1409 Hose Assy 2 
Ref 602.1412 Hose Assy 4

### Page 10

REF. DWG. NO. REPORT 
 614.3000 SB2010-03 
ALERT SERVICE BULLETIN  Rev. C 
  12/21/11 
 
Copyright 2010-2011 Apical Industries, Inc.    Page 10 of 11 
All Rights Reserved 
 
 
 
Figure 10:  Bell 206L-L4 Port Fitting and Hose Routing, LH shown, RH 
Symmetrical  
 
Parts List for Figure 10 
Find Number Part Number Description Qty  
19 602.1410 Hose Assy 2 
29 614.8701 Port Fitting L.H. 1 
32 602.1419 Hose Assy 2 
33 602.1431 Hose Assy 2 
40 614.8702 Port Fitting R.H. 1 
Ref 602.1410 Hose Assy 2 
Ref 602.1412 Hose Assy 4

### Page 11

REF. DWG. NO. REPORT 
 614.3000 SB2010-03 
ALERT SERVICE BULLETIN  Rev. C 
  12/21/11 
 
Copyright 2010-2011 Apical Industries, Inc.    Page 11 of 11 
All Rights Reserved 
 
 
6.0 Service Bulletin Kit Information  
 
1. The table below provides the Service Bulletin kit information. 
 
Service Bulletin Kit Information 
Service 
Bulletin Kit 
Part Number 
Existing 
Float Kit 
Part 
Number 
Bill of Materials 
Comments Part 
Number  Description Qty 
SB2010-03-1 
614.3001 
614.3004 
 
602.1429 Hose Assy 2 
Bell 407 614.8709 Port Fitting Adapter 2 
601.0789 Nut (MS21043-3) 6 
SB2010-03-2 
614.3003 
614.3006 
 
602.1431 Hose Assy 2 
Bell 206L-
Series 614.8709 Port Fitting Adapter 2 
601.0789 Nut (MS21043-3) 6 
SB2010-03-3 
614.3007 
614.3008 
 
602.1430 Hose Assy 2 
Bell 206A, B 614.8709 Port Fitting Adapter 2 
601.0789 Nut (MS21043-3) 6

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
