# APPH Service Bulletin 32-40: Revision 1

- Rights: © APPH. Filed by the FAA in regulations.gov docket FAA-2014-0020; AD 2014-07-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [APPH Service Bulletin 32-40](https://openairdocs.org/service-documents/apph/sb-32-40.md)
- Title as filed: U.S. DOT/FAA - APPH Ltd 32-40
- Pages: 7
- PDF: https://openairdocs.org/files/sha256/b9/11/b9117e0e1f8fff3764396c0ffd42aa0813baaab365400ec95f7405f47c994f17
- Page: https://openairdocs.org/service-documents/apph/sb-32-40/file/b9117e0e1f8f

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

APPH Ltd.
Page  1
June 21/89 Revision 1 Feb 03 32–40
Engineering Division,  Unit 1,  Pembroke Court,  Chancellor Road,  Manor Park,  Runcorn,
Cheshire, WA7 1TG, England.
  FAX (+44) 01928 579626    TEL (+44) 01928 532600
SERVICE BULLETIN
32–40
 LANDING GEAR – MAIN GEAR – INSPECT CYLINDER WEB FOR CRACKS
1. PLANNING INFORMATION
A. Effectivity
(1) Units  Affected:  Main Gear – Port Types: 1863/1 to /8  without strike-off 3
B00A702850A without strike-off 7
B00A702925A without strike-off 5
Main Gear - Starboard Types 1864/1 to /8  without strike-off 3
B00A702851A without strike-off 7
B00A702926A without strike-off 5
(2) Items Affected Cylinder – Port 186316 (pre mod EHM–27)
Cylinder – Starboard 186416 (pre mod EHM–27)
Cylinder – Port 186318 (pre mod 81/05/007)
Cylinder – Starboard 186418 (pre mod 81/05/007
B. Reason
A crack, which has been attributed to fatigue, has been reported originating from the
redundant microswitch hole in the cylinder spigot web.
C. Description
This service bulletin requires an NDT inspection to be made for signs of cracking around
the hole in the cylinder rear spigot web and in the area at the rear edge of the web.
D. Compliance
For Compliance, refer to BAE SYSTEMS Jetstream Service Bulletin 32–A–JA851226.
E. Approval
The contents of this bulletin have been approved under Civil Aviation Authority Design
Approval Number DAI/1033/39.
F. Manpower
Assuming the main gear to be available for inspection, allow 2 manhours to complete the
inspection detailed in this bulletin.
G. Material, cost and availability – Not applicable.
H. Tooling – Not applicable.

### Page 2

Page  2
32–40June 21/89 Revision 1 Feb 03
 LANDING GEAR – MAIN GEAR – INSPECT CYLINDER WEB FOR CRACKS
I. Weight and Balance – Not affected.
J. Electrical Load Data – Not Applicable.
K. References
(1) BAE SYSTEMS Jetstream service bulletin 32–A–JA851226
L. Other Publications Affected
(1) APPH Overhaul Manual 32–10–1 (Formerly BAe Dynamics).
2. ACCOMPLISHMENT INSTRUCTIONS
With the main gear removed from the aircraft and available for inspection proceed as follows:
A. Materials and Equipment (Alternative equivalents can be used)
The following equipment is necessary for the inspection.
(1) Hocking locator UH crack detector.
(2) Non ferrous ‘bolt hole’ probe 2 MHz.
(3) Non ferrous shielded spade 2 MHz.
(4) Standard calibration block, 3 slot.
(5) Inhibisol (solvent) to BS4487.
(6) Epoxy primer to MIL–PRF–23377 Type 1, Class C.
(7) Gloss paint MIL–P–85285 Type 1, FED–STD 595, Colour 16440 or (DTD 5555)
Colour BS381C Code 627 DEF STAN 03–7/1.
(8) Alocrom 1200 to MIL–C–5541 Class 1A (DTD906/4413).
(9) Paint remover, Ardrox 20 to AFS 1426 or plastic abrasive.
B. Prepare cylinder (Fig. 3)
(1) At the first application of this service bulletin blend out the wirelock hole, remove any
corrosion and sharp edges in accordance with Fig. 3.  When this action is complete
mark L67 adjacent to the part number using the same method of marking as
previously used.
(2) Remove the paint from the web around hole and edge with paint remover ‘Ardrox
20’ or other approved paint remover.  Alternatively, plastic abrasive can be used.
Clean the area using Inhibisol or suitable solvent .

### Page 3

Page  3
June 21/89 Revision 1 Feb 03 32–40
 LANDING GEAR – MAIN GEAR – INSPECT CYLINDER WEB FOR CRACKS
C. Set and calibrate test set.
(1) Train and zero equipment on calibration block.
(2) Using the sensitivity control, calibrate test set to give 80% of full scale meter
deflection from 0.019 inch (0.5 mm) slot in standard calibration block. Re–check the
zero.
(3) Connect ‘bolt hole’ probe to lead and test set and set in accordance with the test set
calibration instructions.
(4) Insert ‘bolt hole’ probe into hole in cylinder web and train by gently rocking probe in
hole.  Make sure that the train lights operate.  Zero the test set with the probe tip
facing inwards toward the leg.
(5) Check for correct training by rocking the probe to illuminate the lift–off light.  Make
sure that the meter deflection does not exceed 20% Full Scale Deflection (FSD).
D. Inspect the main gear cylinder web. (Figs. 1 and 2)
(1) Push probe through hole until the end of the probe is flush with the web face. This
will position the probe tip about 0.040 inch (1 mm) from edge of hole.
(2) Carry out a 360 degree scan in this position and at 0.079 inch (2 mm) intervals
throughout the hole.
(3) Connect shielded spade probe to lead and test set, and set up in accordance with
the test set calibration instructions.
(4) Position probe in scan area on inboard face of web and train equipment (ref. Fig.1).
(5) Check for correct training on web face in a similar position.
(6) Position probe on inboard spot face at position X, 0.059 inch (1.5 mm) from edge
of web, and zero the equipment.
(7) Carry out a scan (B) (Fig.1) in both directions from position X to approximately 90
degrees around the hole each way.
(8) Position probe 0.059 inch (1.5 mm) from edge of chamfer and zero equipment.
(9) Maintaining 0.059 inch (1.5 mm) distance from chamfer, carry out a 360 degree scan
(C) around hole (Fig.1).
(10) Place the probe on aft edge of web at position Y, 0.059 inch (1.5 mm) from inboard
face, and zero the equipment (Fig.2).
(11) Maintaining 0.059 inch (1.5 mm) distance from the edge, carry out scan (D) along
the edge of the web (Fig.2).
(12) Repeat the scans detailed in paras (3) to (10) on spot face on outboard face of web.
(13) Cracks up to 0.050 inch (1.27 mm) deep can be blended out.  After blending, the
surface finish must be perfectly smooth and free from marks.
(14) Any crack found in excess of 0.05 inch (1.27 mm) deep renders the cylinder
unserviceable.  The cylinder must then be replaced before further flight.
(15) Repair small cracks within the limitations of para. 2.D. (13) or repair corrosion in
accordance with Fig.3.

### Page 4

Page  4
32–40June 21/89 Revision 1 Feb 03
(16) Small cracks and corrosion which are blended out must be subjected to full NDT
inspection before applying primer and paint.
E. Reprotect repaired area
(1) Protect any area where the surface finish has been removed using Alocrom 1200
followed by primer and polyurethane paint.
F. Record compliance with this Service Bulletin.
(1) Record compliance with this Service Bulletin in the aircraft log book and in the log
cards for the port and starboard main gear.
(2) Record compliance with this Service Bulletin in the aircraft log book and in the log
cards for the port and starboard main gear.
G. MATERIAL INFORMATION
Not applicable.
4. ISSUING AUTHORITY
Signed..............................................................Date.......22–4–03.....
CHIEF DESIGN ENGINEER – APPH  LIMITED

### Page 5

Page  5
June 21/89 Revision 1 Feb 03 32–40
 LANDING GEAR – MAIN GEAR – INSPECT CYLINDER WEB FOR CRACKS
SPOT FACE
CHAMFER
SCAN PATH ‘C’
WEB
TYPICAL DEFECT
POSITION ‘X’
SCAN PATH ‘B’
Aft Web Face (Inboard Face is Similar)
Figure 1

### Page 6

Page  6
32–40June 21/89 Revision 1 Feb 03
POSITION Y
TYPICAL DEFECT
SCAN PATH ‘D’
WEB
Aft Edge of Web
Figure 2

### Page 7 (OCR)

apph
CORROSION INSIDE BORE
MAY BE SMOOTHLY BLENDED
OUT TO 0 03 INCH (0 762mm)
MAX DEPTH
0 62 INCH (15.75mm)  BLEND SMOOTHLY 0.13 INCH
RAD  (3.3mm) RAD ALL CORNERS
THUS
0.13 INCH (3.3mm)
RAD ALL ROUND  SECTION 'A - A'
0.15 INCH
(3.81 mm) MAX  REMOVE WIRELOCK
HOLE BY BLENDING
AS SHOWN
SCRAP VIEW 'B
BLEND SHARP CORNERS
TO 0.13 INCH (3.3mm) RAC
AS SHOWN
Removal of Corrosion
Figure 3
June 21/89 Revision 1 Feb 03  32-40
Page 7

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
