# ATR Service Bulletin ATR42-55-0014

Copy: No revision named ("U.S. DOT/FAA - ATR42-550014
Service Bulletin - Rev. 00"), 19 pages: PDF https://openairdocs.org/files/sha256/0d/d5/0dd59085a927b57c59b37749d883f9d4a850a412e73c07cde9b0ee52c3424f7c; text https://openairdocs.org/service-documents/atr/atr42-55-0014/file/0dd59085a927.md. Rights: © ATR. Filed by the FAA in regulations.gov docket FAA-2011-0721; AD 2011-23-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [ATR](https://openairdocs.org/service-documents/atr.md)
- Type: Service bulletin (Service Bulletin)
- Number: ATR42-55-0014
- Page: https://openairdocs.org/service-documents/atr/atr42-55-0014

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2011-23-10](https://openairdocs.org/ad/2011-23-10.md), effective Dec 15, 2011: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/atr/atr42-55-0014/proposed.md).

## Text (19 pages)

Rights: © ATR. Filed by the FAA in regulations.gov docket FAA-2011-0721; AD 2011-23-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
  Page TS-1 of TS-1 
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
TRANSMITTAL SHEET 
Original issue 
This page transmits Original issue of Service Bulletin No. ATR42-55-0014. 
General information concerning this document is available in Service Letter No. ATR42-00-5005. 
TITLE: Stabilizers - LH and RH elevators - Inboard  hinge fittings - Inspection of lower 
stop fitting angles 
1 – TABLE OF CONTENTS  
TRANSMITTAL SHEET ...................................................................................Page TS-1 to TS-1 
ACCOMPLISHMENT REPORT ...................................................................... Page AR-1 to AR-2 
PLANNING INFORMATION............................................................................... Page PI-1 to PI-5 
MATERIAL INFORMATION.............................................................................. Page MI-1 to MI-2 
ACCOMPLISHMENT INSTRUCTIONS ............................................................. Page AI-1 to AI-7 
ILLUSTRATIONS................................................................................................ Page IL-1 to IL-2 
 
2 – REVISION SEQUENCES  
 
Issue or Revision Date Additional work 
   
Original issue May 11/10 -

### Page 2

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
  Page AR-1 
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
ACCOMPLISHMENT REPORT  
SERVICE BULLETIN No. ATR42-55-0014 
Original issue 
Send this report to: 
ATR ENGINEERING 
SERVICE BULLETIN GROUP 
1 ALLEE PIERRE NADOT 
31712 BLAGNAC CEDEX 
FRANCE 
phone : +33 (0)5 62 21 62 21 
fax : +33 (0)5 62 21 69 41 
e-mail : techdesk@atr.fr 
 
Aircraft identification 
Service Bulletin accomplished on aircraft MSN: 
Service Bulletin accomplishment date: 
Aircraft registration number: 
Number of flights: 
Flight hours:

### Page 3

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
  Page AR-2 
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
Inspection results 
Tick (3) the appropriate box 
  Item 1    Item 2 Remarks 
Which damaged angles have you found on 
the LH side elevator? 
   
Which damaged angles have you found on 
the RH side elevator? 
   
    
Performed actions    
    
    
    
 
 
 
Maintenance organisation identification 
Maintenance organisation name: 
Name & Signature: 
Date:

### Page 4

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
 Page PI-1  
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
COMPLIANCE:  MANDATORY    INSPECTION:  002/2010 
 
TITLE: Stabilizers - LH and RH elevators - Inboard  hinge fittings - Inspection of lower 
stop fitting angles 
1. PLANNING INFORMATION  
A. EFFECTIVITY  
(1) Aircraft models 
ATR42-200 ATR42-300 ATR42-320 ATR42-400 ATR42-500 
YES YES YES YES YES 
 
(2) Aircraft 
MSN Kit(s)  
003, 004, 005, 006, 007, 009, 010, 011, 013, 
014, 015, 016, 018, 019, 020, 021, 022, 023, 
024, 025, 027, 030, 031, 032, 033, 035, 036, 
038, 039, 041, 042, 043, 044, 045, 047, 049, 
050, 051, 052, 053, 054, 055, 057, 058, 059, 
060, 061, 062, 063, 064, 066, 067, 068, 069, 
070, 072, 075, 078, 079, 080, 081, 082, 085, 
086, 087, 088, 089, 090, 091, 092, 093, 095, 
096, 097, 102, 103, 104, 106, 107, 109, 110, 
112, 113, 115, 116, 117, 118, 119, 120, 121, 
122, 123, 125, 128, 130, 131, 132, 133, 134, 
135, 136, 137, 138, 139, 141, 142, 143, 148, 
149, 151, 152, 155, 158, 159, 161, 165, 166, 
169, 170, 172, 173, 176, 178, 179, 182, 187, 
188, 190, 191, 193, 194, 196, 197, 199, 200, 
202, 203, 205, 206, 208, 209, 211, 213, 214,  
None

### Page 5

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
 Page PI-2  
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
MSN (continued) Kit(s)  
216, 218, 219, 221, 225, 226, 228, 230, 231, 
233, 235, 236, 238, 240, 242, 243, 245, 247, 
250, 252, 254, 255, 257, 262, 264, 266, 268, 
269, 273, 275, 277, 278, 280, 282, 284, 286, 
287, 289, 291, 293, 295, 296, 298, 300, 304, 
306, 308, 310, 312, 314, 315, 317, 319, 321, 
323, 325, 327, 329, 331, 333, 335, 337, 340, 
343, 346, 348, 351, 354, 356, 358, 360, 363, 
366, 368, 371, 374, 376, 378, 380, 382, 384, 
386, 388, 390, 392, 394, 397, 400, 403, 406, 
409, 412, 415, 443, 445, 457, 462, 466, 471, 
474, 476, 480, 484, 487, 490, 491, 495, 497, 
500, 501, 502, 503, 504, 506, 507, 510, 511, 
512, 513, 514, 515, 516, 518, 520, 522, 524, 
526, 528, 530, 532, 534, 537, 539, 542, 544, 
546, 549, 551, 554, 556, 559, 561, 564, 566, 
569, 571, 574, 576, 579, 581, 584, 586, 589, 
591, 594, 596, 599, 601, 602, 603, 604, 605, 
606, 607, 608, 609, 610, 611, 612, 613, 614, 
615, 616, 617, 618, 619, 620, 621, 622, 623, 
625, 627, 629, 631, 633, 635, 637, 639, 641, 
643, 645, 647, 649, 651, 653, 655, 657, 659, 
661, 663, 665, 667, 669, 671, 673, 675, 689, 
691, 693, 695, 800, 801, 802, 803, 804, 807, 
815 
None 
 
(3) Spares 
The following stock items are modifiable (or not) according to the table below. 
None. 
B. REASON  
At level of LH and RH side elevator front spars, some inner and/or outer angles of the 
lower stop fitting installed on inboard hinge fittings have been found cracked on several 
aircraft. 
This Service Bulletin consists in inspecting these angles and in replacing them if 
necessary.

### Page 6

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
 Page PI-3  
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
COMPLIANCE: Accomplishment of this Service Bulletin is mandatory.  
An Airworthiness Directive will be issued by EASA. 
C. DESCRIPTION  
Accomplishment of this Service Bulletin consists in carrying out the following jobs: 
(1) In zones 334 and 344, general visual inspection 
(2) In zones 334 and 344, detailed visual inspection of lower stop angles of inboard hinge 
According to inspection results: 
(3) In zones 334 and/or 344, removal of the concerned elevator(s) 
(4) On the bench, on the LH elevator, replacement of the damaged angle(s)  
(5) On the bench, on the RH elevator, replacement of the damaged angle(s) 
(6) In zones 334 and/or 344, re-installation of the removed elevator(s) 
D. APPROVAL  
The technical content of this document is approved in accordance with  
CE 1702/2003 regulation and is rendered mandatory by an EASA Airworthiness Directive. 
E. MANPOWER  
(1) Valid for aircraft on which there is no angle replaced 
 Manhours 
Mechanic  4 
Electrician None 
Total manhours 4 
Elapsed time (hours) 2

### Page 7

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
 Page PI-4  
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
(2) Valid for aircraft on which there are four angles replaced 
 Manhours 
Mechanic  60 
Electrician None 
Total manhours 60 
Elapsed time (hours) 30 
 
The above estimates are only provided for general guidance in operator's modification 
planning. 
NOTE: This Service Bulletin assumes that the aircraft has been placed in the appropriate 
maintenance configuration. The manhours/elapsed time estimates do not include 
preparation for the inspection, non-productive elapsed time or administrative 
functions. 
F. WEIGHT AND BALANCE  
None. 
G. REFERENCES  
The following publications have to be used during accomplishment of this Service Bulletin: 
AMM : 06-41-30 
   
AMM (JIC) : 24-40-00 EAD 10000
55-20-00 RAI 10000
   
NDTM : 51-90-00 
   
SRM : 51-22-03 
51-35-00

### Page 8

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
 Page PI-5  
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
H. AFFECTED PUBLICATIONS  
The following publications will be updated after receipt of the Accomplishment Report by 
ATR. 
None.

### Page 9

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
  Page MI-1 
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
2. MATERIAL INFORMATION  
A. MATERIAL - COST AND AVAILABILITY  
(1) Material 
Parts cost and availability, or any further commercial information about Service 
Bulletin, may be consulted through ATRactive or operator should contact ATR at the 
following addresses: 
www.atractive.com 
 
ATR CUSTOMER SERVICES 
SPARES SUPPORT 
1 ALLEE PIERRE NADOT 
31712 BLAGNAC CEDEX 
FRANCE 
phone : +33 (0)5 62 21 60 33 
fax : +33 (0)5 62 21 62 80 
e-mail : spares.quotations@atr.fr 
 
Or operator should contact the ATR center he is related to, according to his 
operational area, at the following addresses: 
ATR NORTH AMERICA  
45195 BUSINESS COURT, SUITE 450 
DULLES, VIRGINIA 20166 
USA 
phone : +1 571 203 6920 
fax : +1 571 203 6903 
e-mail : commercialservices@atrnorthamerica.com 
 
ATR EASTERN SUPPORT Pte Ltd. 
77 LOYANG WAY 
SINGAPORE 508765 
phone : +65 6542 0122 
fax : +65 6542 1047 
 
Operator should place his purchase order specifying parts reference through 
ATRactive or to the ATR center he is related to according to his operational area.

### Page 10

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
  Page MI-2 
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
B. LIST OF COMPONENTS  
Item Part Number Qty Description 
    
 Material    
    
1 S5527200021401 2 Angle 
2 S5527200021201 2 Angle 
5 S5527200021000 2 Shim 
10 NTA12250-5DD12 4 Rivet 
11 NTA12250-4DD12 4 Rivet 
15 MS21074L3 4 Nut 
16 NTA12350-3A3 8 Rivet 
    
 
NOTE: These quantities are maximum and are presented for the replacement of the four 
angles. 
C. LIST OF MATERIALS - OPERATOR SUPPLIED  
Item Description Reference SRM 51-35-00 Qty per  aircraft 
    
 Polysulfide sealant 09-001F As required 
 Alodine 13-002 As required 
 Primer 16-001C As required 
    
 
NOTE: The above materials can be procured by means of a spares purchase order. 
D. SPECIAL TOOLS  
Accomplishment of this Service Bulletin requires use of the following special tools: 
None.

### Page 11

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
  Page AI-1 
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
3. ACCOMPLISHMENT INSTRUCTIONS  
A. GENERAL  
The following instructions assume that work will be accomplished when the aircraft is in 
the appropriate maintenance configuration. 
B. JOB SET-UP  
(1) De-energize the aircraft electrical network and connect the aircraft to ground as per 
AMM (JIC) 24-40-00 EAD 10000. 
(2) Display warning notice in flight compartment prohibiting operation of elevator control. 
(3) In zones 334 and 344, remove access panels 333CB and 343CB (Refer to  
AMM 06-41-30). 
(4) Maintain elevators in full nose up position (trailing edge upward). 
C. INSPECTION  
(1) In zones 334 and 344, general visual inspection 
Perform a general visual inspection on inboard hinge fitting area at level of LH and RH 
elevator front spars as per NDTM 51-90-00. 
In case of findings, contact ATR for approved solution to: 
ATR ENGINEERING 
STRUCTURE DEPARTMENT 
phone : +33 (0)5 62 21 65 61 
fax : +33 (0)5 62 21 62 92 
e-mail : techdesk@atr.fr 
 
(2) In zones 334 and 344, detailed visual inspection of lower stop angles of inboard hinge 
fittings 
As per Figure 1 
Position a mirror behind lower stops installation and perform a detail visual inspection 
of lower stop angles Item 1 and Item 2 as per NDTM 51-90-00. 
Pay a particular attention to check absence of cracks in radius.

### Page 12

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
  Page AI-2 
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
If there is no damage, perform Para 3.F. 
In case of damage perform Para. 3.D., 3.E. and 3.F. 
Para. 3.D.(2) has to be performed in case of damage detected on LH elevator 
angle(s). 
Para. 3.D.(3) has to be performed in case of damage detected on RH elevator 
angle(s). 
D. MODIFICATION  
(1) In zones 334 and/or 344, removal of the concerned elevator(s) 
Remove the concerned elevator(s) as per AMM (JIC) 55-20-00 RAI 10000. 
(2) On the bench, on the LH elevator, replacement of the damaged angle(s)  
(a) Removal of the stop 
Remove all the parts listed in the following table. 
REMOVAL     
Item Description Part Number Qty Discarded Qty  Re-used Figure
      
3 Screw NAS1802-3-10 - 2 1 
4 Stop S5527200020000 - 1 1 
5 Shim S5527200021000 1 - 1 
      
 
(b) Removal of the damaged angle(s) 
As per Figure 1, sheets 1 and 2 
Remove the damaged angle Item 1, P/N S5527200021400 and/or angle Item 2,  
P/N S5527200021200 with rivet Item 10, P/N NTA12250-5DD (Qty 1 per angle)  
and rivet Item 11, P/N NTA12250-4DD (Qty 1 per angle).

### Page 13

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
  Page AI-3 
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
(c) Perform a detail visual inspection of adjacent areas. 
In case of findings, contact ATR for approved solution to: 
ATR ENGINEERING 
STRUCTURE DEPARTMENT 
phone : +33 (0)5 62 21 65 61 
fax : +33 (0)5 62 21 62 92 
e-mail : techdesk@atr.fr 
(d) Installation of the new angle(s) 
As per Figure 1, sheets 1 and 2 
1 Put in position the new shim Item 5, P/N S5527200021000 on the stop  
Item 4, P/N S5527200020000 retained at removal Para. 3.D.(2)(a). 
Be careful to position the laminated portion of the shim Item 5 in contact with 
the stop Item 4. 
2 Install the stop/shim assembly on the hinge fitting Item 20. 
Take care to ensure flat contact between hinge fitting Item 20 and shim  
Item 5. 
Respect a gap of 0.3 mm ± 0.2 mm (0.0118 in ± 0.0078 in) between the 
stop/shim assembly and the elevator front spar horizontal flange. 
3 Put and maintain in position the stop/shim assembly on the hinge fitting  
Item 20. 
4 Put and maintain in position the new angle(s) Item 1, P/N S5527200021401 
and/or Item 2, P/N S5527200021201 in contact with the hinge fitting Item 20 
and the shim Item 5. 
5 Drill hole(s) A between 4.826 mm and 4.928 mm (0.190 in and 0.194 in). 
Remove stop/shim assembly and the angle(s). 
Protect hole(s) A with Alodine Material No. 13-002 and Primer Material 
No. 16-001C (Refer to SRM 51-35-00). 
6 Install new nut Item 15, P/N MS21074L3 (Qty 1 per angle), attach with rivet 
Item 16, P/N NTA12350-3A3 (Qty 2 per nut). 
7 As per Figure 1, sheet 2, section H-H (schematic for flat contact checking) put 
in position the angle(s) on the hinge fitting flanges Item 20. Using the stop 
Item 4, check the correct alignment between angles Items 1 and 2 and the 
hinge fitting flanges Item 20. 
The flange of angles does not protrude from hinge flanges.

### Page 14

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
  Page AI-4 
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
8 Install new angle Item 1, P/N S5527200021401 and/or new angle Item 2, 
P/N S5527200021201, attach with rivet Item 10, P/N NTA12250-5DD12  
(Qty 1 per angle) and rivet Item 11, P/N NTA12250-4DD12 (Qty 1 per angle). 
9 Install new shim Item 5, P/N S5527200021000 and stop Item 4,  
P/N S5527200020000 (retained at removal Para. 3.D.(2)(a)), attach with 
2 screws Item 3, P/N NAS1802-3-10 (retained at removal Para. 3.D.(2)(a)). 
Be careful to position the laminated portion of the shim Item 5 in contact with 
the stop Item 4. 
Tighten Item 3 at 3 N.m to 3.5 N.m (26.552 in.lbf to 30.978 in.lbf). 
(3) On the bench, on the RH elevator, replacement of the damaged angle(s)  
(a) Removal of the stop 
Remove all the parts listed in the following table. 
REMOVAL     
Item Description Part Number Qty Discarded Qty  Re-used Figure
      
3 Screw NAS1802-3-10 - 2 1 
4 Stop S5527200020000 - 1 1 
5 Shim S5527200021000 1 - 1 
      
 
(b) Removal of the damaged angle(s) 
As per Figure 1, sheets 1 and 2 
1 If the replacement of angle Item 2 is necessary, remove and retain the nut 
Item 6, the screw Item 7 and the washers Items 8 and 9 in order to 
disconnect the two bonding leads. 
2 Remove the damaged angle Item 1, P/N S5527200021400 and/or angle  
Item 2, P/N S5527200021200 with rivet Item 10, P/N NTA12250-5DD  
(Qty 1 per angle) and rivet Item 11, P/N NTA12250-4DD (Qty 1 per angle).

### Page 15

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
  Page AI-5 
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
(c) Perform a detail visual inspection of adjacent areas. 
In case of findings, contact ATR for approved solution to: 
ATR ENGINEERING 
STRUCTURE DEPARTMENT 
phone : +33 (0)5 62 21 65 61 
fax : +33 (0)5 62 21 62 92 
e-mail : techdesk@atr.fr 
(d) Installation of the new angle(s) 
As per Figure 1, sheets 1 and 2 
1 Put in position the new shim Item 5, P/N S5527200021000 on the stop  
Item 4, P/N S5527200020000 retained at removal Para. 3.D.(3)(a). 
Be careful to position the laminated portion of the shim Item 5 in contact with 
the stop Item 4. 
2 Install the stop/shim assembly on the hinge fitting Item 20. 
Take care to ensure flat contact between hinge fitting Item 20 and shim  
Item 5. 
Respect a gap of 0.3 mm ± 0.2 mm (0.0118 in ± 0.0078 in) between the 
stop/shim assembly and the elevator front spar horizontal flange. 
3 Put and maintain in position the stop/shim assembly on the hinge fitting  
Item 20. 
4 Put and maintain in position the new angle(s) Item 1, P/N S5527200021401 
and/or Item 2, P/N S5527200021201 in contact with the hinge fitting Item 20 
and the shim Item 5. 
5 Drill hole(s) A and B between 4.826 mm and 4.928 mm (0.190 in and 
0.194 in). 
Remove stop/shim assembly and the angle(s). 
Protect hole(s) A with Alodine Material No. 13-002 and Primer Material 
No. 16-001C (Refer to SRM 51-35-00). 
6 If angle Item 2 must be replaced, perform an electrical bonding at level  
of hole B on each side of the angle (see detail G, Figure 1) as per  
SRM 51-22-03. 
7 Install new nut Item 15, P/N MS21074L3 (Qty 1 per angle), attach with rivet 
Item 16, P/N NTA12350-3A3 (Qty 2 per nut).

### Page 16

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
  Page AI-6 
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
8 As per Figure 1, sheet 2, section H-H (schematic for flat contact checking) put 
in position the angle(s) on the hinge fitting flanges Item 20. Using the stop 
Item 4, check the correct alignment between angles Items 1 and 2 and the 
hinge fitting flanges Item 20. 
The flange of angles does not protrude from hinge flanges. 
9 Install new angle Item 1, P/N S5527200021401 and/or new angle Item 2, 
P/N S5527200021201, attach with rivet Item 10, P/N NTA12250-5DD12  
(Qty 1 per angle) and rivet Item 11, P/N NTA12250-4DD12 (Qty 1 per angle). 
10 Install new shim Item 5, P/N S5527200021000 and stop Item 4,  
P/N S5527200020000 (retained at removal Para. 3.D.(3)(a)), attach with 
2 screws Item 3, P/N NAS1802-3-10 (retained at removal Para. 3.D.(3)(a)). 
Be careful to position the laminated portion of the shim Item 5 in contact with 
the stop Item 4. 
Tighten Item 3 at 3 N.m to 3.5 N.m (26.552 in.lbf to 30.978 in.lbf). 
11 If the angle Item 2 has been removed at Para. 3.D.(3)(b) and replaced,  
re-install, as per Figure 1 Detail G, the two bonding leads and attach them 
with the nut Item 6, the screw Item 7 and the washers Items 8 and 9 retained 
at Para. 3.D.(3)(b). 
Tighten the nut Item 6 at 2 N.m ± 0.2 N.m (17.701 in.lbf ± 1.770 in.lbf). 
Protect bonding lead terminals and associated fasteners with polysulfide 
sealant Material No. 09-001F (Refer to SRM 51-35-00). 
(4) In zones 334 and/or 344, re-installation of the removed elevator(s) 
Re-install the removed elevator(s) as per AMM (JIC) 55-20-00 RAI 10000. 
E. TESTS  
Verify that tests required by maintenance documents (AMM (JIC) 55-20-00 RAI 10000) 
mentioned on previous paragraph "MODIFICATION" have been performed. 
F. CLOSE-UP  
(1) In zones 334 and 344, install access panels 333CB and 343CB  
(Refer to AMM 06-41-30). 
(2) Remove warning notice in flight compartment prohibiting operation of elevator control.

### Page 17

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
  Page AI-7 
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
(3) Re-energize the aircraft electrical network and disconnect the aircraft from ground as 
per AMM (JIC) 24-40-00 EAD 10000. 
(4) Fill the enclosed Accomplishment Report and send it to the address mentioned on the 
Accomplishment Report.

### Page 18

SERVICE BULLETIN ATR42 
 
Original issue - May 11/10 Service Bulletin No. ATR42-55-0014 
 
  Page IL-1 
©Copyright 2010 Avions de Transport Régional - ATR - All rights reserved. 
Printed in France 
 
 
 
 
ILLUSTRATIONS 
 
Inspection and removal/installation of angles 
Figure 1, sheet 1 of 2

### Page 19 (OCR)

AR  SERVICE BULLETIN ATR42
SECTION  SECTION
E-E  F-F
RH ELEVATOR ONLY
20-  20  BONDING LEADS
D3—  ©:
10
SECTION  SECTION
H-H  H-H
SCHEMATIC FOR FLAT CONTACT CHECKING  SCHEMATIC FOR FINAL INSTALL
4
TIGHTEN SCREW ITEM 3 AT 3 N.m TO 3.5 N.m
(26.552 in.Ibf TO 30.978 in.Ibf)
SOLID PART OF THE SHIM
LAMINATED PART OF THE SHIM
TIGHTEN NUT ITEM 6 AT 2 N.m + 0.2 N.m (17.701 in.Ibf + 1.770 in.Ibf)
PROTECT WITH POLYSULFIDE SEALANT MATERIAL No. 09-001F
(REFER TO SRM 51-35-00)
KEY
FASTENER HEAD ON VISIBLE SIDE
Inspection and removal/installation of angles
Figure 1, sheet 2
Original issue - May 11/10  Service Bulletin No. ATR42-55-0014
Page IL-2
Copyright 2010 Avions de Transport Régional - ATR- All rights reserved.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
