# Austro Engine Engine Mandatory Service Bulletin MSB-E4-034/3: Revision 3, from page 13

- Rights: © Austro Engine. Filed by the FAA in regulations.gov docket FAA-2021-0946; AD 2021-22-20 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Austro Engine Engine Mandatory Service Bulletin MSB-E4-034/3](https://openairdocs.org/service-documents/austro-engine/msb-e4-034-3.md)
- Title as filed: MSB-E4-034-r3
- Pages: 22
- PDF: https://openairdocs.org/files/sha256/77/5e/775e6996f1f6359c34efbbd3d6024f2b56ff5c721060850a0128bf4f0f9ee2ff
- Page: https://openairdocs.org/service-documents/austro-engine/msb-e4-034-3/file/775e6996f1f6

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 13

Mandatory Service Bulletin 
No. MSB-E4-034/3 
Austro Engine GmbH 
Rudolf-Diesel-Strasse 11 
A-2700 Wiener Neustadt 
Tel: +43 2622 23000 
FAX: +43 2622 23000-2711 
 
First Issue Date  Rev. No. Revision Date   Page 
11 Aug 2021 3 30 09 2021 13-22 
© 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at 
 
2. TECHNICAL DETAILS 
2.1. ACCOMPLISHMENT / INSTRUCTIONS 
2.1.1. Removal and Inspection of the HPP driving gear 
1. Remove the HPP in accordance with the instructions in Maintenance Manual, Doc. No. 
E4.08.04, Section 73-10-03, Paragraph A. 
2. Remove the drive gear from the HPP in accordance with the instructions in Maintenance 
Manual, Doc. No. E4.08.04, Section 73-10-03, Paragraph C. 
CAUTION: Use only the tool p/n AE300T012-1 provided in the kit of this Service Bulletin to 
block the gear. 
3. To remove the gear from the shaft, use a bearing extractor shown in Section 3.2. 
4. Clean the driving gear with non-chlorinated brake cleaner (recommended product 
Manufacturer: Förch, Product ID.: R510)  
5. Visually inspect the driving gear against colour criteria in Table 2 - Driving gear 
check.  
If the acceptable criteria are not met: 
• remove the camshafts according to the Maintenance Manual, Doc. No. 
E4.08.04, Section 85-30-00 Subparagraph 4A (a) - (h) 
• Inspect the cylinder head, camshaft gear, the inlet/outlet camshaft bushing in 
accordance with the Service Bulletin MSB-E4-035, replace the parts as necessary. 
 
2.1.2. Installation of the new driving gear 
 
2.1.2.1 Driving gear p/n E4A-30-000-201 rev. AB1 or E4A-30-000-601 
1. Install the new drive gear in accordance with the instructions in Maintenance Manual, 
Doc. No. E4.08.04, Section 73-10-03, Paragraph D (replace the nut, if required). 
Note:  Lubricate the gear and the O-ring with engine oil before installing the HPP 
CAUTION: Use only the tool p/n AE300T012-1 provided in the kit of this Service Bulletin to 
block the gear. 
2. Install the HPP in accordance with the instructions in Maintenance Manual, Doc. No. 
E4.08.04, Section 73-10-03, Paragraph B. Refer also to Table 3 for the tightening 
sequence of the screws. 
3. Mark a tool cycle on the Tool Cycle Recording Sheet (included as appendix in this 
Service Bulletin) and fill the execution report. 
Note:  One cycle equals the disassembly of the old gear and the installation of the new 
gear. 
CAUTION: When the assembly wrench has reached 100 cycles, discard the tool. 
4. Conduct an engine ground run of 15 mins, of which 5 mins are MTOP (maximum 
take-off power).

### Page 14

Mandatory Service Bulletin 
No. MSB-E4-034/3 
Austro Engine GmbH 
Rudolf-Diesel-Strasse 11 
A-2700 Wiener Neustadt 
Tel: +43 2622 23000 
FAX: +43 2622 23000-2711 
 
First Issue Date  Rev. No. Revision Date   Page 
11 Aug 2021 3 30 09 2021 14-22 
© 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at 
 
5. After the ground run, do the following steps: 
o remove the HPP – refer to the Maintenance Manual, Doc. No. E4.08.04, 
Section 73-10-03, Paragraph A  
o Clean and inspect the HPP driving gear against the criteria in MSB-E4-035, 
latest revision. If acceptable criteria are not met: 
▪ remove the camshafts – refer Maintenance Manual, Doc. No. E4.08.04, 
Section 85-30-00 Subparagraph 4A (a) - (h) 
▪ Inspect the cylinder head, camshaft, camshaft gear, the inlet/outlet 
camshaft bearings in accordance with the Service Bulletin E4-035, 
replace the parts as necessary. 
  
6. Install again the HPP in accordance with the instructions of the Maintenance Manual, 
Doc. No. E4.08.04, Section 73-10-03, Paragraph B. 
 
 
2.1.2.2 Driving gear p/n E4A-30-000-201 Rev. AE.1 or subsequent  
 
1. Install the new drive gear (Refer to Figure 1) in accordance with the instructions in 
Maintenance Manual, Doc. No. E4.08.04, Section 73-10-03, Paragraph D (replace the 
nut, if required).  
Use a standard open-ended wrench (27 mm) instead of the special tool. 
Note:  Lubricate the gear and the O-ring with engine oil before installing the HPP 
2. Install the HPP in accordance with the instructions in Maintenance Manual, Doc. No. 
E4.08.04, Section 73-10-03, Paragraph B. Refer also to Table 3 for the tightening 
sequence of the screws. 
 
Note:  With Rev. AE of the driving gear, the engine ground run should be conducted 
acc. to the MM (NO 5 min. at MTOP are needed). 
Note:  With Rev. AE of the driving gear, an inspection after the ground run is not 
required.

### Page 15

Mandatory Service Bulletin 
No. MSB-E4-034/3 
Austro Engine GmbH 
Rudolf-Diesel-Strasse 11 
A-2700 Wiener Neustadt 
Tel: +43 2622 23000 
FAX: +43 2622 23000-2711 
 
First Issue Date  Rev. No. Revision Date   Page 
11 Aug 2021 3 30 09 2021 15-22 
© 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at 
Table 2 - Driving gear check 
 
Fig. 1 
 
Fig. 2 
 
Fig. 3 
 
Fig. 4 
Examples of gear in acceptable conditions 
 
Fig. 5 
 
Fig. 6 
 
Fig. 7 
 
Fig. 8 
Examples of gear in not acceptable condition 
 
Fig. 9 
 
Fig. 10 
 
Fig. 11 
 
Fig. 12 
Examples of gear in not acceptable condition 
 YES NO Consultation with AE required 
Part acceptable:    
Note: • The possible discoloration shown in the non-acceptable gears is due to high 
friction, which generates heat. When present, the typical discoloration is 
not homogeneous and presents different shades from black/blue to 
violet/bronze. 
• Check the gear according to the discoloration criteria provided.  
• Discoloration is clearly visible on the outer surface of the gear  and in the 
marking zone of the gear.  
• Check also for visible discoloration on the face of the teeth. 
• Check for excessive wear of the gear. 
 
In case of doubt contact Austro Engine. 
 
 
X 
X X 
X 
X 
X X X 
 √ 
 √  √ 
 √

### Page 16

Mandatory Service Bulletin 
No. MSB-E4-034/3 
Austro Engine GmbH 
Rudolf-Diesel-Strasse 11 
A-2700 Wiener Neustadt 
Tel: +43 2622 23000 
FAX: +43 2622 23000-2711 
 
First Issue Date  Rev. No. Revision Date   Page 
11 Aug 2021 3 30 09 2021 16-22 
© 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at 
 
Figure 1 – Driving gear E4A-30-000-201 Rev. AE.1 
  
 
  
Table 3 – High Pressure Pump Tightening Sequence 
 
Figure 2 
Install the HPP tightening the screws clockwise, according 
to the figure 1 sequence with 12 Nm.: 
- Step 1 – 1 at 50% 
- Step 2 – 2 at 50% 
- Step 3 – 3 at 50% 
- Step 4 - 1 at 100% 
- Step 5 - 2 at 100% 
- Step 6 - 3 at 100% 
 
1 
3 
2

### Page 17 (OCR)

Austro Engine GmbH
Austro Engine  Mandatory Service Bulletin  No. MSB-E4-034/3  A-2700 Wiener Neustadt  Rudolf-Diesel-Strasse 11  Tel: +43 2622 23000
FAX: +43 2622 23000-2711
Process summarised
Check for
applicability of the
MSB-E4-034 at the
latest revision
Was the
MSB-E4-034 at
revision 0  -YES-
applied?
NO
Remove the HPP
Remove the HPP
driving gear, and
inspect against
Is the Gear
Go to
-NO  in acceptable  YES
conditions?
Install a new gear
and the reinstall the
HPP
is the HPP Gear
'ES  p/n E4A-30-000-201  NO
rev. AE1 or subsequent
installed?
Perform an engine  Perform an engine
ground run according to  ground run (5min.
Maintenance Manual  MTOP)
Remove of the HPP
and inspect the gear
Go to  Is the Gear in
-NO  acceptable
A  conditions?
YES
RELEASE
TO  Reinstall the HPP
SERVICE
First Issue Date  Rev. No.  Revision Date  Page
11  Aug  2021  3  30  09  2021  17-22
© 2021 by Austro Engine GmbH - AUSTRIA - www.austroengine.at

### Page 18 (OCR)

Austro Engine GmbH
JAustro Engine  Mandatory Service Bulletin  Rudolf-Diesel-Strasse 11  A-2700 Wiener Neustadt
No. MSB-E4-034/3  Tel: +43 2622 23000
FAX: +43 2622 23000-2711
Replace the HPP
driving Gear
Inspect the camshaft
and the camshaft
gear
Remove the parts
according to the
latest revision of
manual, then  the maintenance  inlet/outlet camshaft  Inspect the bearing  those parts if  Replace
necessary
inspect against
the criteria
provided in the
MSB-E4-035
Inspect the cylinder
head
is the HPP Gear
rev. AE1 or subsequent  p/n E4A-30-000-201  -YES
installed?
NO
Perform an engine
ground run (5min.
MTOP)  Perform an engine
ground run according to
Maintenance Manual
Remove of the HPP and
inspect the gear
Is the Gear in  RELEASE
-NO  acceptable  -YES-  TO
conditions?  SERVICE
First Issue Date  Rev. No.  Revision Date  Page
11  Aug  2021  30  09  2021  18-22
© 2021 by Austro Engine GmbH - AUSTRIA - www.austroengine.at

### Page 19

Mandatory Service Bulletin 
No. MSB-E4-034/3 
Austro Engine GmbH 
Rudolf-Diesel-Strasse 11 
A-2700 Wiener Neustadt 
Tel: +43 2622 23000 
FAX: +43 2622 23000-2711 
 
First Issue Date  Rev. No. Revision Date   Page 
11 Aug 2021 3 30 09 2021 19-22 
© 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at 
2.2. ILLUSTRATIONS 
None. 
2.3. MASS (WEIGHT) 
Not affected. 
2.4. APPROVAL STATEMENT 
The techn ical content  of this document is  approved under the authority of the DOA ref.  
EASA.21J.399. 
 
3. PLANNING INFORMATION 
3.1. MATERIAL & AVAILABILITY 
Quantity Part Description Part Number 
1 HPP Drive Gear E4A-30-000-601 or E4A-30-000-201 Rev. AB.1 or E4A-30-000-201 Rev. AE.1 
2 Gasket DIN7603-12x16x2.0 
2 Gasket DIN7603-A12x16-AL 
1 Holder wrench HPP AE300T012-1 
 
Caution: The assembly wrench can be used for 100 cycles, after that the tool is not serviceable 
and must be scraped. 
3.2. SPECIAL TOOLS 
No. Description Note 
1 Holder wrench HPP This special tool is provided as part of this SB and it is limited to 100 cycles 
2 Bearing extractor Refer to Figure 3 (not part of the service bulletin kit) 
 
 
Figure 3 – Bearing Extractor

### Page 20

Mandatory Service Bulletin 
No. MSB-E4-034/3 
Austro Engine GmbH 
Rudolf-Diesel-Strasse 11 
A-2700 Wiener Neustadt 
Tel: +43 2622 23000 
FAX: +43 2622 23000-2711 
 
First Issue Date  Rev. No. Revision Date   Page 
11 Aug 2021 3 30 09 2021 20-22 
© 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at 
3.3. LABOR EFFORT 
2 hours for a replacement of an acceptable gear, up to 16 hours for a replacement of a non-
acceptable gear that requires additional part inspections and/or parts replacement. The exact 
time depends on the components that might require replacement and do not include the waiting 
time between correspondence. 
 
 
4. REMARKS 
   
 NOTE: 
 
o All measures must b e carried out by a cert ified engine station and certified engine 
mechanics. 
 
o The accomplishment of the instructions shown under Section 2.1 must be confirmed in 
the respective engine log book. 
 
o The accomplishment of the instru ctions must be carried ou t within the time of 
compliance according chapter 1. 
 
o In case o f doubt please contact the Austro Engine GmbH  – After S ales S upport  
(e-mail: service@austroengine.at; Tel: +43 2622 23000 2525). 
 
o For credit inf ormation contact A ustro En gine G mbH – After Sales  Support  
(e-mail: service@austroengine.at; Tel: +43 2622 23000 2525)  
 
5. EXPLANATORY NOTES 
5.1. SYMBOL EXPLANATION  
  
 CAUTION: Disregarding these special instructions and safety measures can cause  
   damage to the engine or other components. 
 
   NOTE:  Additional note or instruction for better understanding of an instruction

### Page 21

Mandatory Service Bulletin 
No. MSB-E4-034/3 
Austro Engine GmbH 
Rudolf-Diesel-Strasse 11 
A-2700 Wiener Neustadt 
Tel: +43 2622 23000 
FAX: +43 2622 23000-2711 
 
First Issue Date  Rev. No. Revision Date   Page 
11 Aug 2021 3 30 09 2021 21-22 
© 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at 
 
6. APPENDIX 
 
 
HPP Wrench Cycles recording sheet 
Note: 
For each cycle, mark a cross on the corresponding box. When 100 cycles are 
reached, discard the wrench. 
1 Gear replacement (removal & installation) = 1 cycle 
1 2 3 4 5 6 7 8 9 10 
11 12 13 14 15 16 17 18 19 20 
21 22 23 24 25 26 27 28 29 30 
31 32 33 34 35 36 37 38 39 40 
41 42 43 44 45 46 47 48 49 50 
51 52 53 54 55 56 57 58 59 60 
61 62 63 64 65 66 67 68 69 70 
71 72 73 74 75 76 77 78 79 80 
81 82 83 84 85 86 87 88 89 90 
91 92 93 94 95 96 97 98 99 100 
HPP Drive gear wrench p/n

### Page 22

Mandatory Service Bulletin 
No. MSB-E4-034/3 
Austro Engine GmbH 
Rudolf-Diesel-Strasse 11 
A-2700 Wiener Neustadt 
Tel: +43 2622 23000 
FAX: +43 2622 23000-2711 
 
First Issue Date  Rev. No. Revision Date   Page 
11 Aug 2021 3 30 09 2021 22-22 
© 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at 
 
 
Service Bulletin Execution Report 
Note: 
Aircraft owner:   
Aircraft Operator:  If different from the owner 
Aircraft:   
Aircraft Serial Number:   
Aircraft Marks:   
Engine (RH) s/n:  For single engine a/c, fill only 
one row 
Engine (LH) s/n:   
Flight Hours:   
Service center:  Company Name or reference 
of the  person(s) p erforming 
the oil pump replacement 
Removed HPP Gear s/n:  Refer to the figure below to 
identify the serial number  
NOTE:  A scanned version of this form must be provided to service@austroengine.at  
NOTE: The original filled version of  this form, must be packed with the removed gear, and 
provided to Austro Engine  
 
 
Figure 4 – Gear s/n location

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
