# Aviation Partners Boeing Service Bulletin AP737-27-002

Copy: APB SB 737-27-002 Rev 4 ("APB SB 737-27-002 Rev 4"), 58 pages: PDF https://openairdocs.org/files/sha256/11/c9/11c91f5c769c0f9c62df199af8ec1fefe5e96d7029a31105e6566588175a5dbb; text https://openairdocs.org/service-documents/aviation-partners-boeing/ap737-27-002/file/11c91f5c769c.md. Rights: © Aviation Partners Boeing. Filed by the FAA in regulations.gov docket FAA-2016-7270; AD 2017-18-16 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Aviation Partners Boeing](https://openairdocs.org/service-documents/aviation-partners-boeing.md)
- Type: Service bulletin (Service Bulletin)
- Number: AP737-27-002
- Latest revision known: AP737-27-002, Revision 4, dated April 24, 2017 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/aviation-partners-boeing/ap737-27-002

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2017-18-16](https://openairdocs.org/ad/2017-18-16.md), effective Oct 16, 2017: Revisions 1, 2, 3 and 4

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/aviation-partners-boeing/ap737-27-002/proposed.md).

## Text (58 pages)

Rights: © Aviation Partners Boeing. Filed by the FAA in regulations.gov docket FAA-2016-7270; AD 2017-18-16 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN
2811 S 102nd Street, Suite 200
Seattle, WA 98168
(206) 830-7699
NUMBER:  AP737-27-002  REVISON TRANSMITTAL SHEET
Original Issue:  March 31, 2015
Revision 4:  April 24, 2017
ATA SYSTEM: 2741
SUBJECT:  FLIGHT CONTROLS - Horizontal Stabilizer Trim Control System
- Take-Off Nose-Up Trim Limit Correction
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
No more work is necessary on airplanes that were changed in accordance with the
previous versions of this service bulletin.
REASON FOR REVISION
This revision is sent to make the following changes to the service bulletin.
• Page 1: Updated Proprietary Note.
• Page 4: Replaced "that require" with "configure with" two places (ECR-1468).
• Page 4: Deleted "to be replaced" two places (ECR-1468).
• Page 7: Added", replace flight deck control stand pitch light plates, and update
FMC software." to Group 1 and 2 description (ECR-1468).
• Page 7: Added ", and update FMC software." To Group 3 description (ECR-
1468).
• Page 13 Pub. Affected: Added D638A001, Aircraft Illustrated Parts Catalog and
34-61-00 to table (ECR-1321).
• Page 16, 22, and 32: Added preferred BMS3-38 and made BMS3-27 alternate
CIC (ECR-1427).
• Page 19 Note item 4: Added drawing 65-88700 and reworded for clarity (ECR-
1468).
• Page 21: Added "Condition 1" two places and "Condition 2" one place (ECR-
1468).
• Page 21: Replaced "store" with "keep reusable parts (hardware)" (ECR-1427).
• Page 22: Added "Condition 2" and "if removed in step 10." one place (ECR-
1468).
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page i
Aviation Partners Boeing PROPRIETARY

### Page 2 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN
2811 S 102nd Street, Suite 200
Seattle, WA 98168
(206) 830-7699
• Page 32: Was: "Skip steps 9 through 11 and go to step 12"; Is: "Skip steps 10
through 12 and go to step 13" (ECR-1460).
• Page 39 and 40: Replaced "keeping all hardware" with "keep reusable parts
(hardware)" two places. Replaced "hardware" with "reusable parts (hardware)"
two places (ECR-1427).
• Page 40: Added light plate wire caution (ECR-1427).
• Page 46: Added "or U13" one place (ECR-1468).
• Page 47: Added FMC OPS Version U13 to Table 5 (ECR-1468).
REVISION HISTORY
Original Issue:  March 31, 2015
Revision 1:  August 6, 2015
Revision 2:  March 1, 2016
Revision 3:  July 19, 2016
Revision 4:  April 24, 2017
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page ii
Aviation Partners Boeing PROPRIETARY

### Page 3 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
APB DOCUMENT FEEDBACK FORM
To provide feedback on this document to APB for corrections or improvements, please complete
the form below and fax or email to the attention of APB Liaison Engineering at:
Fax: +1 (206) 767-0535
Email: leng@aviationpartners.com
Airline Name:
Contact Name:
Phone Number:
Email Address:
Airplane Model-Type:
Document Number:
Document Revision:
Document Title:
Chapter-Section-Subject:
Page:
Page Date:
Description of Change:
(Include additional sheets as required)
Attachments:
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page ili
Aviation Partners Boeing PROPRIETARY

### Page 4 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN
2811 S 102nd Street, Suite 200
Seattle, WA 98168
(206) 830-7699
NUMBER:  AP737-27-002
Original Issue:  March 31, 2015
Revision 4:  April 24, 2017
ATA SYSTEM: 2741
SUBJECT:  - Take-Off Nose-Up Trim Limit Correction  FLIGHT CONTROLS - Horizontal Stabilizer Trim Control System
PROPRIETARY NOTICE
The data contained hereon and herein is proprietary to Aviation Partners Boeing.
Neither this data nor the data contained herein shall be reproduced, used or disclosed
to others without the written authorization of Aviation Partners Boeing.
EXPORT CONTROLLED TECHNOLOGY
This document contains information about a technology controlled by the Export
Administration Regulations (EAR) (15 CFR 730-774). It has been classified under
Export Control Classification Number (ECCN) 9E991 and may not be exported to
certain countries without a license. Providing this information to a foreign national -
inside or outside the United States - can constitute a prohibited export. Each person
handling this document has a legal responsibility to comply with all applicable EAR
requirements and should consult with an Export Control Officer before providing it to
any foreign national.
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 1 of 54
Aviation Partners Boeing PROPRIETARY

### Page 5 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
Table of Contents
SUBJECT  Page
1.  PLANNING INFORMATION.
A.  EFFECTIVITY  4
B.  CONCURRENT REQUIREMENTS..  5
C.  REASON.  6
D.  DESCRIPTION  7
COMPLIANCE..  9
F..  APPROVAL.  9
G. WARRANTY INFORMATION..  . 9
MANPOWER.  .. 9
WEIGHT AND BALANCE CHANGES..  11
J.  ELECTRICAL LOAD DATA  11
K.  REFERENCES.  11
L.  PUBLICATIONS AFFECTED .  13
M.  INTERCHANGEABILITY AND INTERMIXABILITY OF PARTS.  14
N.  SOFTWARE ACCOMPLISHMENT SUMMARY  14
2.  MATERIAL INFORMATION  15
A.  MATERIAL - PRICE AND AVAILABILITY .  15
B.  PARTS NECESSARY TO CHANGE EACH AIRPLANE  15
C..  SPECIAL TOOLING - PRICE AND AVAILABILITY  17
D.  SPECIAL TOOLING NECESSARY TO DO THIS SERVICE BULLETIN.  . 18
3. ACCOMPLISHMENT INSTRUCTIONS..  • 19
A. GENERAL NOTES.....  . 19
B. WORK INSTRUCTIONS...  .. 21
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 2 of 54
Aviation Partners Boeing PROPRIETARY

### Page 6 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
List of Tables
Title  Page
Table 1 - Manpower ..  10
Table 2 - Parts Available from APB.....  15
Table 3 - Parts and Material Supplied by the Aircraft Owner/Operator  15
Table 4 - Special Tooling Necessary to Do This Service Bulletin  18
Table 5 - FMC Software Part Number and Compatibility.  47
List of Figures
Title  Page
Figure 1: Areas of Work  8
Figure 2: PART 1 Work Flow  24
Figure 3: Access to Stabilizer Takeoff Warning Switch  25
Figure 4: Stabilizer Takeoff Warning Switch  26
Figure 5: Single Takeoff Warning Switch Relocation with an Existing Hole  27
Figure 6: Single Takeoff Warning Switch Relocation with an Existing Hole - Detail  28
Figure 7: Single Takeoff Warning Switch Relocation with New Holes  29
Figure 8: Single Takeoff Warning Switch Relocation with New Holes- Detail  30
Figure 9: PART 2 Work Flow  34
Figure 10: Double Takeoff Warning Switch Relocation with Existing Holes  35
Figure 11: Double Takeoff Warning Switch Relocation with Existing Holes - Detail  36
Figure 12: Double Takeoff Warning Switch Relocation with New Holes  37
Figure 13: Double Takeoff Warning Switch Relocation with New Holes - Detail  38
Figure 14: Flight deck Control Stand  42
Figure 15: Light Plate Removal  43
Figure 16: Light Plate Installation  44
Figure 17: Light Plate Adjustment  45
Figure 18: Light plate Removal  51
Figure 19: Light Plate Removal  52
Figure 20: Light Plate Hole and Nutplate  53
Figure 21: Light Plate Hole and Nutplate  54
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 3 of 54
Aviation Partners Boeing PROPRIETARY

### Page 7 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
1. PLANNING INFORMATION
A. EFFECTIVITY
1. Aircraft Affected
All 737-700 and 737-700C (including C-40A) series airplanes with STC
installed APB Blended Winglets.
NOTE: 737-700 and 737-700C airplanes with TC installed APB Blended
Winglets must be addressed by Boeing service bulletin 737-27A1306.
This service bulletin is effective for the airplanes shown below that have
installed APB Blended Winglets in accordance with STC ST00830SE except
737-700 airplane line numbers 384 (YG033) and 3128 (YG124). 737-700
airplane line numbers 384 (YG033) and 3128 (YG124) must be addressed by
APB service bulletin AP737-34-005.
This service bulletin effectivity is divided into 3 aircraft Groups according to
the relevant configuration and the SB itself is divided into 5 PARTS. The SB
PARTS are structured to allow their independent accomplishment.
PART 1 is applicable to Group 1 and Group 3 only.
PART 2 is applicable to Group 2 only.
PART 3 is applicable to Group 1 and Group 2 only.
PART 4 is applicable to Group 1, 2 and 3.
PART 5 is applicable to Group 3 only.
Software updates in PART 4 may be accomplished prior to hardware
modifications in PART 1, 2, 3 and 5.
Group 1 aircraft are manufacturing line number 1 through 3099 (not including
Group 3 aircraft) configured with a single horizontal stabilizer position limit
and warning switch (S132).
Group 2 aircraft are manufacturing line number 3100 and on configured with
double horizontal stabilizer position limit and warning switches (S132 and
S1184).
Group 3 aircraft are 737-700IGW (BBJ) line number 101 through 684 that
have OEM light plates that have not been replaced by APB light plates in
accordance with APB service bulletin APB737-27-001.
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 4 of 54
Aviation Partners Boeing PROPRIETARY

### Page 8 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
GROUP  Airplane Model  Top Collector Winglet Kit Configuration
737-700  737-7000-1, 737-7000-3,
737-7000-5, 737-7003-1,
737-7003-3, 737-7003-7,
1  737-7005-1, 737-7005-3,
737-7006-1, 737-7006-5,
737-0000-1 (Not Including Group 3 aircraft)
737-0100-1, 737-0100-3
737-700C  737-7002-1, 737-7002-5, 737-7004-1
2  737-700  737-7005-3, 737-7005-5
737-700  737-0000-1
Group 3 -
Airplane Model: 737-700 IGW (BBJ) that have been included in the effectivity of APB
service bulletin AP737-27-001 as follows but have not been modified in accordance with
АРВ service bulletin АРВ737-27-001.
Line  Customer  Serial
Number  Variable  Number
101  YG001  29102
126  YG003  28581
146  YG006  29273
150  YG007  29251
167  YG009  29142
179  YG010  30076
189  YG011  29139
265  YG022  29317
280  YG023  29268
348  YG030  29149
432  YG024  29269
516  YG068  30754
602  YG071  30789
684  YG074  29971
2. Spares Affected
None.
B. CONCURRENT REQUIREMENTS
None
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 5 of 54
Aviation Partners Boeing PROPRIETARY

### Page 9 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
C. REASON
1. Background
Recent analysis of the trim control system has shown that the 737-700 with
Blended Winglets are not compliant with 14CFR 25.107(e) (4) in worst
case conditions. The nose-up pitch trim limit (green band and warning
horn) for blended winglet equipped 737-700s is set too far aft.
2. Safety Intent
The safety intent of this service bulletin is to correct the nose-up pitch trim
limit location, which, if not corrected, could make the airplane
uncontrollable during take-off if the flight crew mistrims to the full nose-up
position when the aircraft is in an aft-light loading condition at critical flap
settings. (14CFR25 requires that the airplane remain controllable in
mistrimmed conditions). The incorporation of this service bulletin will
ensure that the nose-up pitch trim will be set within safe limits for take-off.
3. Configuration Description
This service bulletin gives instructions to replace the control stand stabilizer
trim light plates in the flight compartment with one that has smaller
greenband limits and to change the location of the nose-up take-off
warning limit switches. This service bulletin also gives instructions to install
new Flight Management Computer (FMC) Model/Engine Database (MEDB)
software, which includes revised take-off settings due to the smaller
greenband limits.
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 6 of 54
Aviation Partners Boeing PROPRIETARY

### Page 10 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
D. DESCRIPTION
This service bulletin provides instructions to replace flight deck control stand
pitch trim light plates, and to relocate the horizontal stabilizer position warning
horn switches). This service bulletin also provides instructions for the software
changes in the Model/Engine Database (MEDB) portion of Flight Management
Computer (FMC).
Group 1:
Relocate a single horizontal stabilizer position limit and warning switch (S132),
replace flight deck control stand pitch light plates, and update FMC software.
Group 2:
Relocate double horizontal stabilizer position limit and warning switches (S132
and S1184), replace flight deck control stand pitch light plates, and update
FMC software.
Group 3:
Relocate a single horizontal stabilizer position limit and warning switch (S132),
replace OEM flight deck control stand pitch light plates, and update FMC
software.
The work in this service bulletin is done in the maintenance zone(s) given
below.
Affected Maintenance Zones
Zone  Area
211  Flight Compartment - Left
212  Flight Compartment - Right
311  Area Aft of Pressure Bulkhead - Left
312  Area Aft of Pressure Bulkhead - Right
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 7 of 54
Aviation Partners Boeing PROPRIETARY

### Page 11 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
HORIZONTAL STABILIZER
TRIM LIMIT SWITCHES
ACCESS DOOR TO
AFT UNPRESSURIZED
COMPARTMENT, 311BL
P61 PANEL
COCKPIT CONTROL STAND
Figure 1: Areas of Work
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 8 of 54
Aviation Partners Boeing PROPRIETARY

### Page 12 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
E. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an
Airworthiness Directive related to this service bulletin. The Airworthiness
Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Aviation Partners Boeing recommends that owners/operators accomplish this
modification within 72 months after the issue date of revision 1 of this service
bulletin.
F. APPROVAL
This service bulletin has been reviewed by the Federal Aviation Administration
(FAA). The repairs and modifications contained herein comply with the
applicable Federal Aviation Regulations (FAR) and are FAA approved, as well
as European Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA)
approved for all EASA/JAA approved airplanes listed in the service bulletin
effectivity. This service bulletin and its approval were based on the airplane as
modified by APB winglet retrofit in accordance with STC ST00830SE.
If an airplane has any other non-Boeing modification or repair that affects a
component or system also affected by this service bulletin, the operator is
responsible for obtaining appropriate regulatory agency approval before
incorporating this service bulletin.
G. WARRANTY INFORMATION
Boeing warranty remedies are available for airplanes with winglets in warranty
per the applicable Blended Winglet System Sales Agreement as of June 8,
2015. (Typically within 48 months of the delivery of airplanes with factory
installed winglets, or 48 months from the delivery of retrofit winglets). For man-
hour and material reimbursement for airplanes in warranty as of the foregoing
date, send a warranty claim to Boeing Warranty & Product Assurance
Contracts.
H. MANPOWER
The table below shows an estimate for the man-hours necessary to accomplish
this service bulletin for each aircraft. This estimate is for direct labor only, done
by experienced personnel. Adjust the estimate with operator man-hour data as
necessary. This estimate does not include lost time. These are some examples
of lost time:
• Time to adjust to the workplace.
• Time to schedule the work.
• Time to inspect the work.
• Time to cure the materials.
• Time to make the parts.
• Time to find the tools.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 9 of 54
Aviation Partners Boeing PROPRIETARY

### Page 13 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
Table 1 - Manpower
PART 1 - RELOCATE SINGLE HORIZONTAL STABILIZER POSITION
WARNING HORN SWITCH
Task  Number of  Man-Hours  Elapsed Time
Persons  (Hours)
Access  1  1  1
Modifications  1  1.5  1.5
TOTAL FOR EACH SHIPSET  2.5  2.5
NOTE: Hours do not include removing electrical power from the airplane.
PART 2 - RELOCATE DOUBLE HORIZONTAL STABILIZER POSITION
WARNING HORN SWITCHES
Task  Number of  Man-Hours  Elapsed Time
Persons  (Hours)
Access  1  1  1
Modifications  1  3  3
TOTAL FOR EACH SHIPSET  4.0  4.0
NOTE: Hours do not include removing electrical power from the airplane.
PART 3 - REMOVE AND REPLACE FLIGHT DECK CONTROL STAND
PITCH TRIM LIGHT PLATES
Task  Number of  Man-Hours  Elapsed Time
Persons  (Hours)
Rework  1  2  2
Perform a  1  1  1
functional test
TOTAL FOR EACH SHIPSET  3.0  3.0
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 10 of 54
Aviation Partners Boeing PROPRIETARY

### Page 14 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
Table 1 - Manpower (Continued)
PART 4 - REVISE FLIGHT MANAGEMENT COMPUTER (FMC) SOFTWARE
Task  Number of  Man-Hours  Elapsed Time
Persons  (Hours)
Install new  1  1  1
MEDB software
Perform a  1  1  1
functional test
TOTAL FOR EACH SHIPSET  2.0  2.0
PART 5 - REMOVE AND REPLACE OEM FLIGHT DECK CONTROL STAND
PITCH TRIM LIGHT PLATES
Task  Number of  Man-Hours  Elapsed Time
Persons  (Hours)
Install light plates
TOTAL FOR EACH SHIPSET  3.0  3.0
1. WEIGHT AND BALANCE CHANGES
Not changed.
J. ELECTRICAL LOAD DATA
Not changed.
K. REFERENCES
1. Existing Data:
a. D633A101-(XXX) Boeing 737-600/700/800/900 Aircraft Maintenance
Manual (AMM). (XXX) Refers to customer specific code, subjects:
20-15-01, 20-15-11, 27-41-00, 27-41-94, 31-51-02, 33-18-00, 34-61-
00, 76-11-03.
b. D634A201 Boeing 737-700 Structural Repair Manual (SRM),
51-40-02, 51-40-03, 51-40-04, 51-40-05.
c. D634A330 Boeing 737-700 IGW SRM, 51-20-01, 51-40-02,
51-40-03, 51-40-04, 51-40-05.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 11 of 54
Aviation Partners Boeing PROPRIETARY

### Page 15 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
d. D634A202 Boeing 737-700 Convertible SRM, 51-40-02, 51-40-03,
51-40-04, 51-40-05.
e. Boeing Standard Overhaul Practice Manual (SOPM), 20-41-02, 20-
43-03.
f. BAC5004-1 Solid Rivet Installation
g. BAC5719 Chemical Conversion Coatings for Aluminum and
Aluminum Alloys
h. BAC5736 Application of Chemical and Solvent Resistant Finishes
2. Data Supplied with This Service Bulletin:
None
3. Installation Drawings Used in the Preparation of This Service Bulletin:
Drawing Number  Title
737-7960  Instl - Limit & Warning switch mod, Stabilizer trim
737-7961  Instl - Control Stand Modification
737-0840  Configuration and Functional Test - Flight
Management Computer, 737-BBJ
737-7840  Configuration and Functional Test - Flight
Management Computer, 737-700
737-7841  Configuration and Functional Test - Flight
Management Computer, 737-700C
These drawings were used to prepare this service bulletin. These drawings
are not necessary to make the specified changes, and are not supplied with
this service bulletin. These drawings may not be applicable to all airplane
configurations or operators.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 12 of 54
Aviation Partners Boeing PROPRIETARY

### Page 16 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
L. PUBLICATIONS AFFECTED
1. Publications:
Publication  Chapter / Section
AP37.1-0600, APB Supplement to  27-41-00, 31-51-02
737-700 IGW BBJ Aircraft
Maintenance Manual
AP37.7-0618, APB Supplement to  27-41-00, 31-51-02
737-700 IGW BBJ Aircraft
Maintenance Manual
AP37.7-0600, APB Supplement to  27-41-00, 31-51-02
737-700 Aircraft Maintenance Manual
AP37.7-0622, APB Supplement to  27-41-00, 31-51-02
737-700C Aircraft Maintenance
Manual
AP37.1-0601, 737-700 IGW Airplane  SECTION 3
Flight Manual Supplement  Flight Management Computer System
SECTION 4
Recommended Takeoff Stabilizer
Setting
AP37.1-0616, 737-700 IGW Airplane  SECTION 3
Flight Manual Supplement  Flight Management Computer System
SECTION 4
Recommended Takeoff Stabilizer
Setting
AP37.7-0601, 737-700 Airplane  SECTION 3
Flight Manual Supplement  Flight Management Computer System
SECTION 4
Recommended Takeoff Stabilizer
Setting
AP37.7-0616, 737-700C Airplane  SECTION 4
Flight Manual Supplement  Recommended Takeoff Stabilizer
Setting
AP37.7-0614, APB Supplement to  76-11-03
737-700 Aircraft Illustrated Parts
Catalog
AP37.7-0625, APB Supplement to  76-11-03
737-700C Aircraft Illustrated Parts
Catalog
AP37.1-0802, Instructions for  Section 1 Introduction
Continued Airworthiness - APB
Winglets STC ST00830SE
D638A001, Aircraft Illustrated Parts  34-61-00
Catalog
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 13 of 54
Aviation Partners Boeing PROPRIETARY

### Page 17 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
2. Damage Tolerance Based Structural Inspections:
APB has evaluated the repairs and/or changes in this service bulletin for
effects on Fatigue Critical Structure (FCS) and for changes to Damage
Tolerance Inspections (DTI) required in the Maintenance Program. This
service bulletin does not affect FCS, therefore no new DTS are necessary.
M. INTERCHANGEABILITY AND INTERMIXABILITY OF PARTS
Refer to Paragraph 2.B., Parts Necessary for Each Airplane, for
interchangeability and intermixability information.
N. SOFTWARE ACCOMPLISHMENT SUMMARY
1. System affected by this change:
Flight Management Computer (FMC)
2. Software changes which affect operational procedures:
None.
3. Other software improvements:
FMC will display the updated nose-up pitch trim limit.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 14 of 54
Aviation Partners Boeing PROPRIETARY

### Page 18 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
2. MATERIAL INFORMATION
A. MATERIAL - PRICE AND AVAILABILITY
Price and availability of material required to accomplish this service bulletin are
as described in Paragraph 2.B, below.
B. PARTS NECESSARY TO CHANGE EACH AIRPLANE
Parts and materials necessary to accomplish this bulletin are shown in Table 3
and 4, below.
1. Parts Available from APB
Required parts are shown in Table 2. These parts should be obtained from
APB via Purchase Order to aogspares@aviationpartners.com. Contact
APB at the same address for current pricing and availability.
Table 2 - Parts Available from APB
Material  Description  QTY per SS  Note
Replaces 737-8618-1
737-8618-3  Light Plate  (Group 1 Aircraft)
Replaces 737-8618-724
(Group 3 Aircraft)
Replaces 737-8618-2
737-8618-4  Light Plate  1  (Group 1 Aircraft)
Replaces 737-8618-725
(Group 3 Aircraft)
2. Parts and Material Supplied by aircraft owner/operator
Aircraft owner/operators are responsible for furnishing the material
identified in this subparagraph.
Table 3 - Parts and Material Supplied by the Aircraft Owner/Operator
Material  Description  QTY per SS
BACR15BB5AD4  Rivet  As required
BACR15CE5AD4  Rivet  As required
BACN10JN04  Nutplate  As required
BACR15DR3AC1  Rivet  As required
NAS1149DN416J  Washer  As required
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 15 of 54
Aviation Partners Boeing PROPRIETARY

### Page 19 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
Material  Description  QTY per SS
MS20995NC20  Lock Wire  1 Roll
MS20995NC32  Lock Wire  1 Roll
BMS 10-11, Type I  Primer  2 ounces
BMS3-38 (Preferred)  Corrosion Inhibiting
BMS3-27 (Alternate)  Material  2 ounces
Alodine 600  Conversion coating  2 ounces
Table 3 - Parts and Materials Supplied by the Operator/Operator (Continued)
Disk Set Title  Disk Set P/N  Software P/N  Notes
34 FMC MEDB  242A6020-1032  BCG-01T-A0  (a) (b) (c)
(a) This software part number is used in production. Operators may
already have this media set.
(b) Only one media set is necessary for each operator.
(c) Get the MEDB disk set from Boeing Spares. Refer to this service
bulletin number in the purchase order.
3. Parts Modified and Re-identified
The parts shown below are changed as shown in this service bulletin.
Quantity is the number of parts changed on each airplane.
Group 3 only:
Existing Part  RUC  Name  QTY  New Part  PNC  RPC
Number  Number
65C31525  RWK  Bracket  1  N  A
65C31526  RWK  Bracket  1  N
RUC Recommended Use Code
RWK Make the change as specified in this service bulletin.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 16 of 54
Aviation Partners Boeing PROPRIETARY

### Page 20 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
PNC Part Number Code
N  There is no equivalent APB part number for the changed part.
Identify on the part that the change given in this service
bulletin was made.
RPC Replacement Code
A Do not use the existing part to replace the new or changed
part.
4. Parts Removed and Not Replaced
None
5. Parts Removed and Replaced
The parts shown below are removed and replaced as shown in this service
bulletin. Quantity is the number of parts changed on each airplane.
Existing Part  RUC  Name  QTY  New Part  PNC  RPC
Number  Number
737-8618-1  DIS  Light Plate  1  737-8618-3  S  A
737-8618-2  DIS  Light Plate  1  737-8618-4  S
RUC Recommended Use Code
DIS Discard the part. Keep the part if there are other uses for it.
PNC Part Number Code
S  This is the part number for the new equivalent or replacement
part. To get a new part, use this part number in your order.
RPC Replacement Code
A Do not use the existing part to replace the new or changed part.
C. SPECIAL TOOLING - PRICE AND AVAILABILITY
Special tools are required to perform modifications in this service bulletin.
Contact APB for tool price and availability.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 17 of 54
Aviation Partners Boeing PROPRIETARY

### Page 21 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
D. SPECIAL TOOLING NECESSARY TO DO THIS SERVICE BULLETIN
See Table 4 for required special tooling.
Aircraft with retrofit winglets will not require a drill jig fixture. Since the nose-up
horizontal stabilizer position warning horn switch position reverts to its original
hole location on airplanes delivered without winglets, no new holes will be
required.
Aircraft with factory installed winglets will require a drill jig fixture to establish
the new switch location.
Table 4 - Special Tooling Necessary to Do This Service Bulletin
Tool Number  Name  QTY  Airplane Group
TE27T-41001-8  Measuring Bar Tool  1  Group 1, 2 and 3
or F80055-1  or Trammel Bar
DJ-737-7960-9L  Drill Jig Fixture  1  Group 1, 2 and 3
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 18 of 54
Aviation Partners Boeing PROPRIETARY

### Page 22 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
3. ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL NOTES
WARNING: IF ELECTRICAL POWER IS APPLIED TO THE AIRPLANE,
MAKE SURE YOU OBEY ALL PRECAUTIONS WHILE YOU DO WORK. IF
YOU DO NOT OBEY THE PRECAUTIONS, DEATH OR INJURY TO
PERSONS, AND DAMAGE TO THE AIRPLANE CAN OCCUR.
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES
CLEAN OF METAL PARTICLES OR CONTAMINATION WHEN YOU USE
TOOLS. UNWANTED MATERIAL, METAL PARTICLES, OR
CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE DAMAGE TO
THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
CAUTION: ELECTRICALLY GROUND THE AIRPLANE. THIS WILL HELP TO
PREVENT DAMAGE TO THE AIRPLANE OR EQUIPMENT.
NOTE: 1. Obey all warnings and cautions given in the applicable sections of
the 737-700 Aircraft Maintenance Manual (AMM).
2. Unless shown differently, these dimensions and tolerances are used:
All linear dimensions, areas, volumes, temperatures, pressures,
weights, and energy will show U.S. Customary Units.
Tolerance on linear dimensions, other than rivet and bolt edge
margins, is plus or minus 0.03 inch.
- Tolerance on rivet and bolt edge margin is plus or minus 0.05
inch.
- Angular tolerance is plus or minus 2 degrees.
Hole dimensions for standard solid rivets are given in the 737
Structural Repair Manual (SRM), 51-40-05.
- Torque limits to tighten nut and bolts are given in the 737
SRM, 51-40-04.
3. Make the following entry into the aircraft's records once service
bulletin is completed:
"Aviation Partners Boeing Service Bulletin AP737-27-002
completed on (date) by (name of individual or company)i
4. For approved fastener and process material substitutions, refer to
the 737 SRM, chapter 51 and Boeing drawing 65-88700.
Alternate fasteners are given in the 737 SRM, 51-40-03 and
Boeing drawing 65-88700.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 19 of 54
Aviation Partners Boeing PROPRIETARY

### Page 23 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
5. If the length of any fastener specified in this service bulletin does
not meet the installation standards in 737 SRM, 51-40-02, then a
fastener of the same specification or an approved substitute, with
a length which meets the installation standards in the 737 SRM,
51-40-03 may be used.
6. If it is necessary to remove more parts for access, you can
remove those parts. If you can get access without removing
identified parts, it is not necessary to remove all of the identified
parts. Jacking and shoring limitations must be observed.
7. Refer to 737-600/700/800/900 AMM 20-15-11 for on-airplane
software installation maintenance practices, as an accepted
procedure.
8. Refer to 737-600/700/800/900 AMM 20-15-01 for off-airplane
software installation maintenance practices, as an accepted
procedure.
9. These work instructions refer to procedures included in other
Boeing documents. When the words "refer to" are used and the
operator has an accepted alternative procedure, the accepted
alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in
the document must be used.
10. The work instructions are divided into PARTS. Task Hours and
Elapsed Hours for each package are given in Paragraph. 1.H. You
may accomplish each PART independently.
11. Some steps in the Work Instructions are identified as Required for
Compliance (RC). If this service bulletin is mandated by an
airworthiness directive (AD), then the steps identified as RC and
steps indented under an RC step must be done to comply with
the AD. Alternative procedures for steps not identified with RC
can be used if the RC steps and indented steps can still be done
as specified, and the airplane can be put back in a serviceable
condition. An Alternative Method of Compliance (AMOC) is not
necessary for deviations to steps that are not identified as RC.
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 20 of 54
Aviation Partners Boeing PROPRIETARY

### Page 24 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
B. WORK INSTRUCTIONS
PART 1 - RELOCATE SINGLE HORIZONTAL STABILIZER POSITION
WARNING HORN SWITCH
Refer to Figure 2 for the work flow.
Note: The diagram only supplements the information in the accomplishment
instructions and is not intended to serve as the primary source for tasks in this
SB.
1. Set the stabilizer trim cutout switches to the CUTOUT position.
2. Open these circuit breakers and install safety tags:
• F/O Electrical System Panel, P6-2
Row  Col  Number  Name
B  10  C00207  FLIGHT CONTROL STAB TRIM CONT
• F/O Electrical System Panel, P6-3
Row  Col  Number  Name
C  18  C01398  LANDING GEAR TAKEOFF WARNING CUTOFF
D  18  C00451  LANDING GEAR AURAL WARN
3. Open this access panel. Refer to Figure 3:
• Stabilizer Trim Access Door 311BL
4. Adjust the stabilizer "B" dimension to 24 inches +/- .01 inch. Refer to Figure 4.
5. Remove S132 switch and mark it as "S132", leaving wire harness attached.
Salvage all hardware except lock wires and keep reusable parts (hardware).
Refer to the 737-600/700/800/900 AMM, 31-51-02 for the removal of the
S132 switch as an accepted procedure.
CAUTION: Excessive axial tension loads on the switch shaft can result in
internal damage to the switch.
6. Locate an existing open hole for S132 switch approximately 1.5 inches above
the current location of S132 switch. Refer to Figure 5.
Condition 1: If the open hole exists, do steps 7, 8 and 9 and go to step 13.
Condition 2: If the open hole does not exist, drill new holes in accordance with
steps 10 through 12.
7. RC for Condition 1, Group 1 and Group 3 aircraft - Drill two new holes in
accordance with Figure 6.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 21 of 54
Aviation Partners Boeing PROPRIETARY

### Page 25 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
8. Remove two rivets next to the open hole. Countersink resulting holes on both
sides of web to a depth of .015 - 020 X 100 deg. Refer to Figure 6. Install
BACR15CE5AD4 rivets. Refer to BAC5004-1 or 737-700 SRM, 51-40-02 as
an accepted procedure. Microshave manufactured head and formed head
flush within +0.005, -0.000 inch after installation. Refer to BAC5004-1 as an
accepted procedure.
9. Manually apply Alodine 600 to bare surfaces including shaved rivet. Refer to
BAC5719 or SOPM 20-43-03 as an accepted procedure. Apply one coat of
BMS10-11, Type I primer. Refer to BAC5736 or SOPM 20-41-02 as an
accepted procedure.
Skip steps 10 through 12 and go to step 13.
10. Remove S144 switch and mark it as "S144",  ", leaving wire harness attached.
Salvage all hardware except lock wires and store. Refer to the 737-
600/700/800/900 AMM, 27-41-94 for the removal of the S144 switch as an
accepted procedure.
CAUTION: Excessive axial tension loads on the switch shaft can result in
internal damage to the switch.
11. Locate drill jig fixture DJ-737-7960-9L and check lower switch hole location
S144 using tooling check pin.
12. RC for Condition 2, Group 1 and Group 3 aircraft - Drill three new holes in
accordance with Figure 7 and 8.
13. Open up two index holes next to the current S132 switch hole to .159 - .167
dia. Install BACR15BB5AD4 rivets. Refer to Figure 8. Refer to BAC5004-1 or
737-700 SRM, 51-40-02 as an accepted procedure.
14. RC for Group 1 and Group 3 aircraft - Install S132 switch in the new
location. Re-install S144 switch in the original location if removed in step 10.
Install 32EN21-4 switch assembly in bracket with BMS3-38 (BMS3-27
acceptable alternate) corrosion inhibiting material. Orient lead wires as shown
+/- 5 degrees. Orient switch arm as shown. Adjust S132 switch. Refer to 737-
600/700/800/900 AMM TASK 31-51-02-820-801 as an accepted procedure.
Adjust S144 switch if removed in step 10. Refer to 737-600/700/800/900
AMM TASK 27-41-94-820-801 as an accepted procedure. Refer to the 737-
600/700/800/900 AMM, 31-51-02 for the installation of switch S132 as an
accepted procedure and 737-600/700/800/900 AMM, 27-41-94 for the
installation of switch S144 as an accepted procedure.
CAUTION: If adjustments are to be completed at a later time, switch arms
should be placed in a position clear of the cam throughout the
entire range of cam motion.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 22 of 54
Aviation Partners Boeing PROPRIETARY

### Page 26 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
15. Remove the safety tags and close these circuit breakers:
F/O Electrical System Panel, P6-2
Row  Col  Number  Name
B  10  C00207  FLIGHT CONTROL STAB TRIM CONT
• F/O Electrical System Panel, P6-3
Row  Col  Number  Name
C  18  C01398  LANDING GEAR TAKEOFF WARNING CUTOFF
18  CO0451 LANDING GEAR AURAL WARN
16. Close this access panel. Refer to Figure 3.
• Stabilizer Trim Access Door 311BL
17. Set the stabilizer trim cutout switches to the NORMAL position.
18. Put the airplane back to a serviceable condition.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 23 of 54
Aviation Partners Boeing PROPRIETARY

### Page 27 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
Step 1 - Set the stabilizer trim
cutout switches to CUTOUT
V
Step 2 - Open the circuit breakers.
Step 3 - Open the access panel.
Step 4 - Adjust the B dimension.
Step 5 - Remove switch S-132.
Step 6 - Open
hole exists?
YES  NO
Step 7 - Drill 2 holes  Step 10- Remove switch S-144
Step 8 - Remove 2 rivets
and plug the holes.  Step 11 - Locate drill jig fixture
Step 9 - Touch up finish.  Step 12 - Drill 3 holes
Step 13- Open up 2 holes and plug
the holes.
Step 14 - Install removed switch(es).
Step 15 - Close the circuit breakers.
Step 16 - Close the access panel.
Step 17 - Set the stabilizer trim cutout
switches to NORMAL.
Note: This diagram only supplements the information in the
accomplishment instructions and is not intended to serve as the
primary source for tasks in this SB.
Figure 2: PART 1 Work Flow
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 24 of 54
Aviation Partners Boeing PROPRIETARY

### Page 28 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
ACCESS DOOR TO
AFT UNPRESSURIZED
COMPARTMENT, 311BL
SEE A
SEE Figure 4
VIEW THROUGH THE ACCESS DOOR TO
AFT UNPRESSURIZED COMPARTMENT, 311BL
Figure 3: Access to Stabilizer Takeoff Warning Switch
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 25 of 54
Aviation Partners Boeing PROPRIETARY

### Page 29 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
ACTUATOR
TRAMMEL BAR
- S132
• S144
DIMENSION
B 1>
FNDO
STABILIZER TRIM ACTUATOR
NOTE: The stabilizer trim jackscrew is shown with the
stabilizer leading edge at zero degrees.
The dimension B is measured between the center of
the upper and lower gimbal pins, (center of grease
fittings).
Figure 4: Stabilizer Takeoff Warning Switch
"B" Dimension Definition
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 26 of 54
Aviation Partners Boeing PROPRIETARY

### Page 30 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
See Figure 6
[5.9368]  Existing
Hole
New S132
Location
Current
S132
Location  Lead Wire
Direction
Switch
Arm
Direction
S144
NOTE: The dimensions apply with B-Dimension at 24 +/- 0.01 inches.
Figure 5: Single Takeoff Warning Switch Relocation with an Existing Hole
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 27 of 54
Aviation Partners Boeing PROPRIETARY

### Page 31 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
STA 1079. 80•
REF
- (2.5445)-
(2.9° )
+ (2.3210)D
251A4700 REF
(4.436)
(5.9368)
Step 8
45°
0.4700 REF
0.76500
Step 7
Step 8  2x ø.1450 - .1500
Ø0.0050€ CS
Step 13
NOTE: The dimensions apply with B-Dimension at 24 +/- 0.01 inches.
Figure 6: Single Takeoff Warning Switch Relocation with an Existing Hole - Detail
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 28 of 54
Aviation Partners Boeing PROPRIETARY

### Page 32 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
2. 5445-
11210
See Figure 8
New
Hole
110. 749)  New S132
Location
Current
S132
Location  Lead Wire
Direction
Switch
АГт
Direction
S144
NOTE: The dimensions apply with B-Dimension at 24 +/- 0.01 inches.
Figure 7: Single Takeoff Warning Switch Relocation with New Holes
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 29 of 54
Aviation Partners Boeing PROPRIETARY

### Page 33 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
STA 1079.80
REF
- (2.5445)•
(2. 9° )
2. 3210
251A4700 REF
4.436
(5.9368)
Step 12
0.4685- .4715
20.0150 AC  ) BO
Step 12
2x ø.1450 - .1500
$ Ø0.00509 CS
Step 13
NOTE: The dimensions apply with B-Dimension at 24 +/- 0.01 inches.
Figure 8: Single Takeoff Warning Switch Relocation with New Holes- Detail
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 30 of 54
Aviation Partners Boeing PROPRIETARY

### Page 34 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
PART 2 - RELOCATE DOUBLE HORIZONTAL STABILIZER POSITION
WARNING HORN SWITCHES
Refer to Figure 9 for the work flow.
Note: The diagram only supplements the information in the accomplishment
instructions and is not intended to serve as the primary source for tasks in this
SB.
1. Set the stabilizer trim cutout switches to the CUTOUT position.
2. Open these circuit breakers and install safety tags:
F/O Electrical System Panel, P6-2
Row  Col  Number  Name
B  10  C00207  FLIGHT CONTROL STAB TRIM CONT
F/O Electrical System Panel, P6-3
Row  Col  Number  Name
18  C01398  LANDING GEAR TAKEOFF WARNING CUTOFF
D  18  C00451  LANDING GEAR AURAL WARN
3. Open this access panel (Refer to Figure 3):
• Stabilizer Trim Access Door 311BL
4. Adjust the stabilizer "B" dimension (Refer to Figure 4) to 24 inches +/- .01
inch.
5. Remove S132 and S1184 switches and mark them as "S132" and "S1184"
respectively, leaving wire harness attached. Remove 3/16 locking nut, 3/16
flat washer, switch arm, 15/32 jam nut, and internal tooth lock washer from
32EN21-4 switch assemblies. Salvage all hardware except lock wires and
store. Refer to the 737-600/700/800/900 AMM, 31-51-02 for the removal of
the S132 and S1184 switches as an accepted procedure.
CAUTION: Excessive axial tension loads on the switch shaft can result in
internal damage to the switch.
6. Locate the existing open holes for S132 and S1184 switches approximately
1.5 inches above the current location of S132 and S1184 switches. (Refer to
Figure 10)
If the open holes exist, do steps 7, 8, and 9 and go to step 13. If the open
holes do not exist, drill new holes in accordance with steps 10 through 12.
7. RC for Group 2 aircraft - Drill four new holes in accordance with Figure 11.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 31 of 54
Aviation Partners Boeing PROPRIETARY

### Page 35 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
8. Remove two rivets next to the open holes. Countersink resulting holes on
both sides of web to a depth of .015 - .020 inch X 100 deg.
Install BACR15CE5AD4 rivets. Refer to BAC5004-1 or 737-700 SRM, 51-40-
02 as an accepted procedure. Microshave manufactured head and formed
head flush within +0.005, -0.000 inch after installation. Refer to BAC5004-1 as
an accepted procedure.
9. Manually apply Alodine 600 to bare surfaces including shaved rivet. Refer to
BAC5719 or SOPM 20-43-03 as an accepted procedure. Apply one coat of
BMS10-11, Type I primer. Refer to BAC5736 or SOPM 20-41-02 as an
accepted procedure.
Skip steps 10 through 12 and go to step 13.
10. Remove S144 switch and mark it as "S144", leaving wire harness attached.
Remove 3/16 locking nut, 3/16 flat washer, switch arm, 15/32 jam nut, and
internal tooth lock washer from 32EN21-4 switch assembly. Salvage all
hardware except lock wires and store. Refer to the 737-600/700/800/900
AMM, 27-41-94 for the removal of the switch as an accepted procedure.
CAUTION: Excessive axial tension loads on the switch shaft can result in
internal damage to the switch.
11. Locate drill jig fixture DJ-737-7960-9L and check lower switch hole location
S144 using tooling check pin.
12. RC for Group 2 aircraft - Drill six new holes in accordance with Figure 12
and 13.
13. Open up two index holes each next to the current S132 and S1184 switch
holes to .159 - 167 dia. Install BACR15BB5AD4 rivets. Refer to BAC5004-1
or 737-700 SRM, 51-40-02 as an accepted procedure. Refer to Figure 13.
14. RC for Group 2 aircraft - Install S132 and S1184 switches in the new
locations. Re-install S144 switch in the original location if removed in step 10.
Install 32EN21-4 switch assemblies in bracket with BMS3-38 (BMS3-27
acceptable alternate) corrosion inhibiting material. Orient lead wires as shown
+/- 5 degrees. Orient switch arm as shown. Adjust S132 and S1184 switches.
Refer to 737-600/700/800/900 AMM TASK 31-51-02-820-801 as an accepted
procedure. Adjust S144 switch. Refer to 737-600/700/800/900AMM TASK 27-
41-94-820-801 as an accepted procedure. Refer to the 737-600/700/800/900
AMM, 31-51-02 for the installation of switch S132 and switch S1184 as an
accepted procedure and 737-600/700/800/900 AMM, 27-41-94 for the
installation of switch S144 as an accepted procedure.
CAUTION: If adjustments are to be completed at a later time, switch arms
should be placed in a position clear of the cam throughout the
entire range of cam motion.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 32 of 54
Aviation Partners Boeing PROPRIETARY

### Page 36 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
15. Remove the safety tags and close these circuit breakers:
•  F/O Electrical System Panel, P6-2
Row  Col  Number  Name
B  10  C00207  FLIGHT CONTROL STAB TRIM CONT
• F/O Electrical System Panel, P6-3
Row  Col  Number  Name
C  18  C01398  LANDING GEAR TAKEOFF WARNING CUTOFF
18  CO0451 LANDING GEAR AURAL WARN
16. Close this access panel. Refer to Figure 3.
• Stabilizer Trim Access Door 311BL
17. Set the stabilizer trim cutout switches to the NORMAL position.
18. Put the airplane back to a serviceable condition.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 33 of 54
Aviation Partners Boeing PROPRIETARY

### Page 37 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
Step 1 - Set the stabilizer trim
cutout switches to CUTOUT.
Step 2 - Open the circuit breaker.
Step 3 - Open the access panel.
Step 4 - Adjust the B dimension.
Step 5 - Remove switch S-132 and
S-1184
Step 6 -
Open holes
exist?
YES
Step 7 - Drill 4 holes.  Step 10 - Remove switch S-144.
and plug the holes  Step 8 - Remove 4 rivets  Step 11 - Locate drill jig fixture.
Step 9 - Touch up finish.  Step 12 - Drill 6 holes.
Step 13- Open up 4 holes and plug
the holes.
Step 14 - Install removed switches
Step 15 - Close the circuit breaker.
Step 16 - Close the access panel.
<
Step 17 - Set the stabilizer trim cutout
switches to NORMAL.
Note: This diagram only supplements the information in the
accomplishment instructions and is not intended to serve as the
primary source for tasks in this SB.
Figure 9: PART 2 Work Flow
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 34 of 54
Aviation Partners Boeing PROPRIETARY

### Page 38 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
251A4700
See Figure 11
Existing
Holes
New S1184  New S132
Location  Location
Current
S1184  Current
Location  S132  Lead Wire
Location  Direction
(TYPICAL)
Switch
Arm
Direction
(TYPICAL)
S144
14.5160 1-_
NOTE: The dimensions apply with B-Dimension at 24 +/- 0.01 inches.
Figure 10: Double Takeoff Warning Switch Relocation with Existing Holes
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 35 of 54
Aviation Partners Boeing PROPRIETARY

### Page 39 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
251A4700
(1.1413 ) -
(2.3210)
(3.7320 )
Step 8
(4.4360 )
45 °
0.4700 REF  Step 8
0.4700 REF
Step 7
2x ø • 1500  . 1450
ø. 76500  Step 7
ø.76500
2x Ø • 1500  . 1450
Step 8  Step 8  $ 20. 00509 CS
Step 13
251A4705
REF  Step 13
A - B
NOTE: The dimensions apply with B-Dimension at 24 +/- 0.01 inches.
Figure 11: Double Takeoff Warning Switch Relocation with Existing Holes - Detail
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 36 of 54
Aviation Partners Boeing PROPRIETARY

### Page 40 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
See Figure 13
251A4700 REF
New Holes
New S1184
New S132
Location  Location
Current
( 16. 7490 / S1184  Current
Location  S132  Lead Wire
Location  Direction
(TYPICAL)
Switch
Arm
Direction
(TYPICAL)
S144
- t 4.6160 1.
NOTE: The dimensions apply with B-Dimension at 24 +/- 0.01 inches.
Figure 12: Double Takeoff Warning Switch Relocation with New Holes
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 37 of 54
Aviation Partners Boeing PROPRIETARY

### Page 41 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
1.1413
2.3210-
251A4700-
Step 12
2× Ø •1500  .1450
$ 20.0050€ D€
3.7320
4.4360
Step 12ø ø•4715  . 4685
Step 12
ø • 4715  . 4685
Step 13
251A4705  Step 12
REF  2x ø • 1500
. 1450
* Ø0.0050G CG
- B  Step 13
NOTE: The dimensions apply with B-Dimension at 24 +/- 0.01 inches.
Figure 13: Double Takeoff Warning Switch Relocation with New Holes - Detail
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 38 of 54
Aviation Partners Boeing PROPRIETARY

### Page 42 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
PART 3 - REMOVE AND REPLACE COCKPIT CONTROL STAND PITCH
TRIM LIGHT PLATES
1. Open this access panel. Refer to Figure 3:
• Stabilizer Trim Access Door 311BL
2. Locate the 254A1220 Control Stand in the flight deck of the aircraft.
See Figure 14.
3. RC for Group 1 and Group 2 aircraft - Run stabilizer trim until the stabilizer
pointer on the control stand indicates 4 units. Verify that the stabilizer "B"
dimension is 39.89 inches +/- .10 inch. If the dimension is not within the
specified tolerance, adjust stabilizer to this dimension. Refer to Figure 4.
4. See Figure 15, Figure 16 and Figure 17 for Steps 5 through 19.
5. Remove and retain the right and left side stabilizer trim wheels (part number
254A1370). Retain the BACB30LU8-4 bolts.
6. Remove and retain the right and left side control stand linings (part number
232A1630). Refer to Figure 14.
7. RC for Group 1 and Group 2 aircraft - Remove the left stabilizer light plate
(part number 737-8618-1), keep reusable parts (hardware). Refer to
737-600/700/800/900 AMM 76-11-03 as an accepted procedure.
8. RC for Group 1 and Group 2 aircraft - Remove the right stabilizer light plate
(part number 737-8618-2), keep reusable parts (hardware). Refer to
737-600/700/800/900 AMM 76-11-03 as an accepted procedure.
9. RC for Group 1 and Group 2 aircraft - Verify the Stabilizer "B" dimension as
described in Step 3 of these instructions.
10. RC for Group 1 and Group 2 aircraft - Install the 737-8618-3 light plate
using kept reusable parts (hardware). Refer to 737-600/700/800/900 AMM
76-11-03 as an accepted procedure. Verify that the stabilizer pointer indicates
4 units within half the unit "4" bar width. Adjust the 737-8618-3 light plate as
required to achieve 4 unit indication before tightening screws.
11. Rig indicator assembly (part number 254A1273) pointer (part number
254A1314) to 737-8618-3 light plate laterally. Adjust the face of the pointer
either inboard or outboard within the indicator assembly until a constant gap
of. 0400 to. 1300 inch is achieved between the pointer and the light plate.
Refer to Figure 17. Washers (part number NAS1149DN416J) may be either
added or deleted to achieve this gap.
12. Rig indicator assembly (part number 254A1273) pointer (part number
254A1314) to 737-8618-3 light plate radially. Loosen screws (NAS1352N04-
X) and adjust the upper face of the pointer either up or down to the upper face
of the light plate by sliding the pointer along the indicator. Mismatch shall be
to within +/- .0400 inch. Refer to Figure 17. Tighten screws.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 39 of 54
Aviation Partners Boeing PROPRIETARY

### Page 43 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
CAUTION: Verify that the light plate wiring is adequately supported and clear
of any mechanism inside the control stand. Move the flap, throttle
and speed brake handles full travel and recheck light plate wiring
clearances.
13. RC for Group 1 and Group 2 aircraft - Verify the Stabilizer "B" dimension as
described in Step 3 of these instructions.
14. RC for Group 1 and Group 2 aircraft - Install the 737-8618-4 light plate
using kept reusable parts (hardware). Refer to 737-600/700/800/900 AMM
76-11-03 as an accepted procedure. Verify that the stabilizer pointer indicates
4 units within half the unit "4" bar width. Adjust the 737-8618-4 light plate as
required to achieve 4 unit indication before tightening screws.
15. Rig indicator assembly (part number 254A1274) pointer (part number
254A1314) to 737-8618-4 light plate laterally. Adjust the face of the pointer
either inboard or outboard within the indicator assembly until a constant gap
of .0400 to 1300 inch is achieved between the pointer and the light plate
(Refer to Figure 17). Washers (part number NAS1149DN416J) may be either
added or deleted to achieve this gap.
16. Rig indicator assembly (part number 254A1274) pointer (part number
254A1314) to 737-8618-4 light plate radially. Loosen screws (NAS1352N04-
X) and adjust the upper face of the pointer either up or down to the upper face
of the light plate by sliding the pointer along the indicator. Mismatch shall be
to within +/- .0400 inch (Refer to Figure 17). Tighten screws.
CAUTION: Verify that the light plate wiring is adequately supported and clear
of any mechanism inside the control stand. Move the flap, throttle
and speed brake handles full travel and recheck light plate wiring
clearances.
17. RC for Group 1 and Group 2 aircraft - Perform Light plate functional check
in accordance with 737-600/700/800/900 AMM, 33-18-00, SUBTASK 33-18-
00-710-005. If the Light plate fails the functional check, replace the light plate
and do the functional check again. For removal and installation of a light
plate, refer to 737-600/700/800/900 AMM 76-11-03 as an accepted
procedure. If the Light plate fails the functional check again, contact The
Boeing Company for repair procedures and do the procedures given by The
Boeing Company.
18. Reinstall 232A1630 control stand linings removed in Step 6 of these
instructions.
19. Reinstall right and left stabilizer trim wheels (part number 254A1370)
removed in Step 5 of these instructions. Wheels are to be installed with their
handles 75 to 105 degrees apart. Torque BACB30LU8-4 bolts to 150 - 170
inch pounds.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 40 of 54
Aviation Partners Boeing PROPRIETARY

### Page 44 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
WARNING: KEEP PERSONS AND EQUIPMENT CLEAR OF FLIGHT
CONTROL SURFACES, THRUST REVERSERS, AND THE LANDING
GEAR. THESE COMPONENTS CAN MOVE SUDDENLY WHEN YOU
SUPPLY HYDRAULIC POWER. IT CAN CAUSE INJURIES TO
PERSONS AND DAMAGE TO EQUIPMENT.
20. RC for Group 1 and Group 2 aircraft - Do the Stabilizer Takeoff Warning
Switches Test. Refer to Boeing AMM TASK 31-51-02-700-801 as an
accepted procedure. Do the Stabilizer Trim Limit Switches Test. Refer to
Boeing AMM Task 27-41-00-700-805 as an accepted procedure. If the
airplane does not pass, adjust the horizontal stabilizer trim system. Refer to
AMM TASK 31-51-02-820-801 and TASK 27-41-94-820-801 as accepted
procedures.
21. Close this access panel. Refer to Figure 3:
• Stabilizer Trim Access Door 311BL
22. Put the airplane back to a serviceable condition.
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 41 of 54
Aviation Partners Boeing PROPRIETARY

### Page 45 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
SEE M
SCREW
FLIGHT DECK  (4 LOCATIONS)
UPPER
SIDE
LINING
See Figure 15
LOWER
UPPER  SIDE
SIDE  LINING
LINING
SCREW
(4 LOCATIONS)
SCREW
(4 LOCATIONS)
LOWER
SIDE
LINING  SCREW
(5 LOCATIONS)
FWD  CONTROL STAND
Figure 14: Flight deck Control Stand
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 42 of 54
Aviation Partners Boeing PROPRIETARY

### Page 46 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
LIGHT PLATES
REMOVE
737-8618-1
REPLACE WITH  REMOVE
737-8618-3  737-8618-2
REPLACE WITH
737-8618-4
EAS
254A1370 REF
254A1370 REF  254A1220 REF
Figure 15: Light Plate Removal
View Looking Down
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 43 of 54
Aviation Partners Boeing PROPRIETARY

### Page 47 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
RETAIN
PS4C9DL01BK
254A1370 REF
RETAIN
PS4C9DL01BK
A see Figure 17
RETAIN
PS4C9DL01BK
737 - 8618-4
254A1370 REF
RETAIN
737-8618-3  PS4C9DL01BK
254A1220 REF
Figure 16: Light Plate Installation
View Looking Down
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 44 of 54
Aviation Partners Boeing PROPRIETARY

### Page 48 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
254A1220 REF
- 1300  - 0400  - 0400  1300
- 737-8618-4
737-8618-3
#.0400
$.0400
-254A1314 REF
254A1314 REF
NAS1352N04-X REF  -NAS1352N04-X REF
WAS1149DN416J REF  - NAS1149DN416J REF
(2 PLACES  (2 PLACES)
254A1273 REF
254A1274 REF
Section A-A
Figure 17: Light Plate Adjustment
View Looking Forward
Original Issue: March 31, 2015
Revision 4: April 24, 2017  AP737-27-002
Page 45 of 54
Aviation Partners Boeing PROPRIETARY

### Page 49 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
PART 4 - REVISE FLIGHT MANAGEMENT COMPUTER (FMC) SOFTWARE
1. Get access to the flight compartment.
Verify Flight Management Computer (FMC) Operational Program Software
(OPS) version in Table 5. If FMC OPS version is not U10.8A, U11, U12, or
U13, install a compatible FMC OPS version. Refer to the 737-
600/700/800/900 AMM, 34-61-00 as an accepted procedure.
2. In the flight compartment, do the steps that follow to check the current Flight
Management Computer (FMC) Model/Engine Database (MEDB) configuration
number.
a. Do the Model/Engine Configuration check. Refer to 737-600/700/800/900
AMM 34-61-00 as an accepted procedure.
b. Record the settings shown below.
1) Record the MODEL.
2) Record the BRAKE OPT.
3) Record the ENGINE OPT.
4) Record the FULL & BUMP ENGINE RATINGS.
5) Record the Model/Engine CONFIG number.
3. RC - Load and verify MEDB software noted in Table 5 into the left and then
the right FMC with an Airborne Data Loader or Portable Data Loader. Refer to
737-600/700/800/900 AMM 34-61-00/201 as an accepted procedure.
4. RC - Do the FMC Configuration Check and verify the all settings are the same
as recorded in Step 2.b. Refer to 737-600/700/800/900 AMM 34-61-00 as an
accepted procedure. If the settings are not the same as recorded, contact The
Boeing Company and obey the instructions given by The Boeing Company.
5. Put the airplane back in a serviceable condition.
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 46 of 54
Aviation Partners Boeing PROPRIETARY

### Page 50 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
Table 5 - FMC Software Part Number and Compatibility
Group 1, Group 2 and Group 3:
Name  Disk Set P/N  Software P/N
34 FMC MEDB  242A6020-1032  BCG-01T-A0
Compatible FMC OPS
Reference Service
Name  FMC OPS  Version  Disk Set P/N  Software  P/N  Installation Only  Bulletin for OPS
U10.8A  10-62225-1019  549849-020  737-34A2216*
U11  10-62225-1020  556909-001  737-34-2252
34 FMC OPS
U12  10-62225-1021  559775-001  737-34-2600
U13  10-62225-1022  559777-001  737-34-2906
Note * - Service Bulletin 737-34A2216 calls out FMC MEDB BCG-01J-05.
Disregard and use FMC MEDB BCG-01T-A0 as noted above.
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 47 of 54
Aviation Partners Boeing PROPRIETARY

### Page 51 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
PART 5 - REMOVE AND REPLACE COCKPIT CONTROL STAND PITCH
TRIM LIGHT PLATES
1. Open this access panel. Refer to Figure 3:
• Stabilizer Trim Access Door 311BL
2. Locate the 254A1220 Control Stand in the flight deck of the aircraft.
See Figure 14.
3. RC for Group 3 aircraft - Run stabilizer trim until the stabilizer pointer on the
control stand indicates 4 units. Verify that the stabilizer "B" dimension is 39.89
inches +/-. 10 inch. If the dimension is not within the specified tolerance,
adjust stabilizer to this dimension. Refer to Figure 4.
4. See, Figure 17, Figure 18, Figure 19, Figure 20 and Figure 21 for Steps 5
through 23.
5. Remove and retain the right and left side stabilizer trim wheels (part number
254A1370). Retain the BACB30LU8-4 bolts.
6. Remove and retain the right and left side control stand linings (part number
232A1630). Refer to Figure 14.
7. RC for Group 3 aircraft - Remove the left stabilizer light plate (part number
737-8618-724), retaining all the hardware. Temporarily install the 737-8616-3
light plate in place of the 737-8618-724, using the aft fastener location only.
Verify that the stabilizer pointer indicates 4 units within half the unit "4" bar
width. Mark the location for the forward fastener on the 65C31525 bracket.
8. RC for Group 3 aircraft - Remove the 65C31525 bracket. Retain bracket
and all hardware.
9. RC for Group 3 aircraft - Remove the right stabilizer light plate (part number
737-8618-725), retaining all the hardware. Temporarily install the 737-8616-4
light plate in place of the 737-8618-725, using the forward fastener location
only. Verify that the stabilizer pointer indicates 4 units within half the unit "4"
bar width. Mark the location for the aft fastener on the 65C31526 bracket.
10. RC for Group 3 aircraft - Remove the 65C31526 bracket. Retain bracket
and all hardware.
11. RC for Group 3 aircraft - Rework the 65C31525 bracket by removing the
existing forward light plate attachment nutplate. Drill new forward light plate
hole and attach nutplate as shown in Figure 20 or 21. Touch up finish per
737-700 IGW Structural Repair Manual D634A330, Section 51-20-01.
12. RC for Group 3 aircraft - Part mark modified bracket as 65C31525-SB737-
27-002R2.
13. RC for Group 3 aircraft - Rework the 65C31526 bracket by removing the
existing aft light plate attachment nutplate. Drill new aft light plate hole and
attach nutplate as shown in Figure 20 or 21. Touch up finish per 737-700 IGW
Structural Repair Manual D634A330, Section 51-20-01.
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 48 of 54
Aviation Partners Boeing PROPRIETARY

### Page 52 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
14. RC for Group 3 aircraft - Part mark modified bracket as 65C31526-SB737-
27-002R2.
15. RC for Group 3 aircraft - Reinstall the 65C31525 (737-0910-5) brackets
using retained hardware.
16. RC for Group 3 aircraft - Verify the Stabilizer "B" dimension as described in
Step 3 of these instructions.
indication before tightening screws.
18. Rig indicator assembly (part number 254A1273) pointer (part number
254A1314) to 737-8618-3 light plate laterally. Adjust the face of the pointer
either inboard or outboard within the indicator assembly until a constant gap
of .0400 to. 1300 inch is achieved between the pointer and the light plate.
Refer to Figure 17. Washers (part number NAS1149DN416J) may be either
added or deleted to achieve this gap.
19. Rig indicator assembly (part number 254A1273) pointer (part number
254A1314) to 737-8618-3 light plate radially. Loosen screws (NAS1352N04-
X) and adjust the upper face of the pointer either up or down to the upper face
of the light plate by sliding the pointer along the indicator. Mismatch shall be
to within +/- .0400 inch. Refer to Figure 17. Tighten screws.
20. RC for Group 3 aircraft - Verify the Stabilizer "B" dimension as described in
Step 3 of these instructions.
21. RC for Group 3 aircraft - Install the 737-8618-4 light plate using retained
hardware. Verify that the stabilizer pointer indicates 4 units within half the unit
"4" bar width. Adjust the 737-8618-4 light plate as required to achieve 4 unit
indication before tightening screws.
22. Rig indicator assembly (part number 254A1274) pointer (part number
254A1314) to 737-8618-4 light plate laterally. Adjust the face of the pointer
either inboard or outboard within the indicator assembly until a constant gap
of .0400 to 1300 inch is achieved between the pointer and the light plate
(Refer to Figure 17). Washers (part number NAS1149DN416J) may be either
added or deleted to achieve this gap.
23. Rig indicator assembly (part number 254A1274) pointer (part number
254A1314) to 737-8618-4 light piate radially. Loosen screws (NAS1352N04-
X) and adjust the upper face of the pointer either up or down to the upper face
of the light plate by sliding the pointer along the indicator. Mismatch shall be
to within +/- .0400 inch (Refer to Figure 17). Tighten screws.
CAUTION: Verify that the light plate wiring is adequately supported and clear
of any mechanism inside the control stand. Move the flap, throttle
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 49 of 54
Aviation Partners Boeing PROPRIETARY

### Page 53 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
and speed brake handles full travel and recheck light plate wiring
clearances.
24. RC for Group 3 aircraft - Perform Light plate functional check in accordance
with 737-600/700/800/900 AMM, 33-18-00, SUBTASK 33-18-00-710-005. If
the Light plate fails the functional check, replace the Light plate and do the
functional check again. If the Light plate fails the functional check again,
contact The Boeing Company for repair procedures and do the procedures
given by The Boeing Company.
25. Reinstall 232A1630 control stand linings removed in Step 6 of these
instructions.
26. Reinstall right and left stabilizer trim wheels (part number 254A1370)
removed in Step 5 of these instructions. Wheels are to be installed with their
handles 75 to 105 degrees apart. Torque BACB30LU8-4 bolts to 150 - 170
inch pounds.
WARNING: KEEP PERSONS AND EQUIPMENT CLEAR OF FLIGHT
CONTROL SURFACES, THRUST REVERSERS, AND THE
LANDING GEAR. THESE COMPONENTS CAN MOVE SUDDENLY
WHEN YOU SUPPLY HYDRAULIC POWER. IT CAN CAUSE
INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
27. RC for Group 3 aircraft - Do the Stabilizer Takeoff Warning Switches Test.
Refer to Boeing AMM TASK 31-51-02-700-801 as an accepted procedure. Do
the Stabilizer Trim Limit Switches Test. Refer to Boeing AMM Task 27-41-00-
700-805 as an accepted procedure. If the airplane does not pass, adjust the
horizontal stabilizer trim system. Refer to AMM TASK 31-51-02-820-801 and
TASK 27-41-94-820-801 as accepted procedures.
28. Close this access panel. Refer to Figure 3:
a. Stabilizer Trim Access Door 311BL
29. Put the airplane back to a serviceable condition.
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 50 of 54
Aviation Partners Boeing PROPRIETARY

### Page 54 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
254A1370-6
REMOVE  REMOVE
737-8618-724  737-8618 - 725
REPLACE WITH  REPLACE WITH
737 - 8618-3  737-8618-4
65C31526
65C31525  REF
REF
UP
254A1370 REF  254A1370 REF
254A1220 REF
Figure 18: Light plate Removal
View Looking Forward
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 51 of 54
Aviation Partners Boeing PROPRIETARY

### Page 55 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
254A1370 REF
254A1370 REF
. 1490/. 1590 HOLE
THRU 65C31525
PS4C9DL01BK  - 65C31526 REF
BACN10JN04
2x BACR15DR3AC1.  RETAIN
PS4C9DL01BK
737-8618-3  - 737-8618-4
A Figure 17
254A1273 REF  254A1274 REF
. 1490/ .1590 HOLE
65C31525 REF  THRU 65C31526
PS4C9DL01BK
RETAIN  BACN10JN04
PS4C9DL01BK  2x BACR15DR3AC1
254A1220 REF
Figure 19: Light Plate Removal
View Looking Down
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 52 of 54
Aviation Partners Boeing PROPRIETARY

### Page 56 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
APPROXIMATE LOCATION
EXISTING NUTPLATE (REMOVE)
ELONGATION OF NEW HOLE
PERMISSABLE TO CLEAN UP
EXISTING NUTPLAT HOLE
• 080  +
MIN  - BACN10JN04
. 100 MIN
. 280
MAX
• BACR15DR3AC1
65C31525 REF
Figure 20: Light Plate Hole and Nutplate
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 53 of 54
Aviation Partners Boeing PROPRIETARY

### Page 57 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-27-002
- APPROXIMATE LOCATION
EXISTING NUTPLATE (REMOVE)
. 100 MIN
BACN10JN04
BACR15DR3AC1  . 100 MIN
Figure 21: Light Plate Hole and Nutplate
(Alternative Installation)
Original Issue: March 31, 2015  AP737-27-002
Revision 4: April 24, 2017  Page 54 of 54
Aviation Partners Boeing PROPRIETARY

### Page 58

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
