# Aviation Partners Boeing Service Bulletin AP737-57-020

Copy: No revision named ("AP737-57-020"), 17 pages: PDF https://openairdocs.org/files/sha256/f1/e0/f1e0cd1bf8125ffb5a1ae23b70875a18280c353ca10685d34d5ab0db2d6efd17; text https://openairdocs.org/service-documents/aviation-partners-boeing/ap737-57-020/file/f1e0cd1bf812.md. Rights: © Aviation Partners Boeing. Filed by the FAA in regulations.gov docket FAA-2019-0323; AD 2019-22-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Aviation Partners Boeing](https://openairdocs.org/service-documents/aviation-partners-boeing.md)
- Type: Service bulletin (Service Bulletin)
- Number: AP737-57-020
- Page: https://openairdocs.org/service-documents/aviation-partners-boeing/ap737-57-020

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2019-22-06](https://openairdocs.org/ad/2019-22-06.md), effective Dec 30, 2019: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/aviation-partners-boeing/ap737-57-020/proposed.md).

## Text (17 pages)

Rights: © Aviation Partners Boeing. Filed by the FAA in regulations.gov docket FAA-2019-0323; AD 2019-22-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN
2811 S 102nd Street, Suite 200
Seattle, WA 98168
(206) 830-7699
NUMBER:  AP737-57-020
Original Issue:  April 5, 2018
ATA SYSTEM:  5720
SUBJECT:  WINGS - Stringer U-14 Reinforcement Interference with FQIS Tank Unit at Rib 21, Left Hand
PROPRIETARY NOTICE
The data contained hereon and herein is proprietary to Aviation Partners Boeing. Neither this data nor the
data contained herein shall be reproduced, used or disclosed to others without the written authorization
of Aviation Partners Boeing.
EXPORT CONTROLLED TECHNOLOGY
This document contains information about a technology controlled by the Export Administration
Regulations (EAR) (15 CFR 730-774). It has been classified under Export Control Classification Number
(ECCN) 9E991 and may not be exported to certain countries without a license. Providing this information
to a foreign national - inside or outside the United States - can constitute a prohibited export. Each person
handling this document has a legal responsibility to comply with all applicable EAR requirements and
should consult with an Export Control Officer before providing it to any foreign national.
Original Issue: April 5, 2018  AP737-57-020
Page 1 of 17

### Page 2 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
APB DOCUMENT FEEDBACK FORM
To provide feedback on this document to APB for corrections or improvements, please complete the form below
and fax or email to the attention of APB Liaison Engineering at:
Fax: +1 (206) 767-0535
Email: _leng@aviationpartners.com
Airline Name:
Contact Name:
Phone Number:
Email Address:
Airplane Model-Type:
Document Number:
Document Revision:
Document Title:
Chapter-Section-Subject:
Page:
Page Date:
Description of Change:
(Include additional sheets as
required)
Attachments:
Original Issue: April 5, 2018  AP737-57-020
Page 2 of 17
Aviation Partners Boeing Proprietary

### Page 3 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
Table of Contents
SUMMARY
1.  PLANNING INFORMATION  .6
A.  Effectivity .
1. Airplanes  .6
2. Spares Affected .
B.  Concurrent Requirements
c.  Reason
D  Description
E  Compliance.
Approval  8
G  Warranty Information  .9
H.  Manpower.  .9
Weight and Balance Changes  10
J.  Electrical Load Data  10
K  References  10
1. Existing Data:.  10
2. Data Supplied with This Service Bulletin:  10
3. Installation Drawings Used in the Preparation of This Service Bulletin:  10
L  Other Publications Affected  10
M.  Interchangeability and Intermixability of Parts  10
N.  Software Accomplishment Summary..  10
2.  MATERIAL INFORMATION
A  Material - Price and Availability
B  Parts Necessary for Each Airplane  11
1. Kits/Parts ..  11
2. Parts and Materials Supplied by the Operator:  11
C.  Parts Necessary to Change Spares ...  11
D.  Existing Parts Accountability  11
E.  Special Tooling - Price and Availability.  11
F  Special Tooling Necessary to Do This Service Bulletin  11
3.  ACCOMPLISHMENT INSTRUCTIONS.  12
A.  General Notes..  12
B.  Work Instructions  13
PART 1: INSPECTION OF FQIS TANK UNIT CLEARANCE TO STRINGER U-14 REINFORCEMENT ATT
RIB 21, LEFT HAND...  13
PART 2: REPAIR/TERMINATING ACTION - TRIM STRINGER U-14 REINFORCEMENT TO PROVIDE
CLEARANCE TO FQIS TANK UNIT.  13
PART 3: PUT THE AIRPLANE BACK TO A SERVICEABLE CONDITION  14
FIGURE 1: WING LOWER SURFACE  15
FIGURE 2: FQIS TANK UNIT No. 12 INSTALLATION AT RIB 21  16
Original Issue: April 5, 2018  AP737-57-020
Page 3 of 17
Aviation Partners Boeing Proprietary

### Page 4 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
NUMBER:  AP737-57-020  SUMMARY
Original Issue:  April 5, 2018
ATA SYSTEM:  5720
SUBJECT:  WINGS - Stringer U-14 Reinforcement Interference with FQIS Tank Unit at Rib 21, Left Hand
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR.
CONCURRENT REQUIREMENTS
None
BACKGROUND
This service bulletin is sent to provide instructions to inspect for clearance between the Fuel Quantity Indicating
System (FQIS) tank unit 12 at Rib 21 (WSTA 617) and the Stringer U-14 reinforcement Angle in the left hand
wing. If the work given in this service bulletin is not done, the FQIS installation potentially would not be in
conformance with 28-AWL-30 CDCCL requirements.
One operator has reported finding insufficient clearance on two aircraft during 737-800-7 Split Scimitar Winglet
modifications.
APB resolved both discrepant conditions by providing instructions to trim the free flange of the reinforcement
angle to obtain minimum 0.10 inch clearance to the FQIS tank unit 12. The Materiel Review Report (MRR) repair
dispositions met the 28-AWL-30 CDCCL requirement which states the gap between the side of the tank unit and
tank structure must be 0.10 inch or more.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
Planning Data  Affected  Reference
Spares Affected  No  Paragraph 1.A.2., Spares Affected
AD Related  No  Paragraph 1.E., Compliance and Paragraph
1.F., Approval
Weight and Balance Change  No  Paragraph 1.l., Weight and Balance
Changes
Electrical Load Changed
Publications Affected
Airplane Flight Operations Affected (Flight
Crew Operations Manual and/or FAA
Approved Airplane Flight Manual)
No  Paragraph 1.J., Electrical Load Data
No  Paragraph 1.L., Publications Affected
No  Paragraph 1.L., Publications Affected
Kits/Parts Required  No  Paragraph 2.B.1., Kits/Parts
Operator Supplied Parts/Material  Yes  Paragraph 2.B.2., Parts and Materials
Supplied by the Operator
Special Tooling Required  No  Paragraph 2.F., Special Tooling Necessary
to do this Service Bulletin
Original Issue: April 5, 2018  AP737-57-020
Page 4 of 17
Aviation Partners Boeing Proprietary

### Page 5 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
ACTION
Get access to the inboard side of Rib 21 (WSTA 617) on the left hand wing. Measure the clearance between the
FQIS tank unit and the Stringer U-14 reinforcement angle. If the clearance is less than 0.10 inches, trim away the
lower flange of the reinforcement angle to provide clearance and restore the airplane to a serviceable condition. If
clearance is 0.10 inches or greater, no further rework is necessary. Paragraph 1.E., Compliance contains
compliance times for the inspection and rework.
EFFECTIVITY
737-800 Airplanes from line number 4919 to 5063, modified to receive Split Scimitar Winglets (SSW), with
Blended or Split Scimitar Winglets installed (Refer to STC ST00830SE). Refer to Paragraph 1.A.1., Airplanes, for
the list of affected airplane(s).
COMPLIANCE
Refer to Paragraph 1.E., Compliance Recommendation.
INDUSTRY SUPPORT INFORMATION
None.
MANPOWER
Refer to Paragraph 1.H., Manpower.
MATERIAL INFORMATION
None.
Original Issue: April 5, 2018  AP737-57-020
Page 5 of 17
Aviation Partners Boeing Proprietary

### Page 6 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
NUMBER:  AP737-57-020
Original Issue:  April 5, 2018
ATA SYSTEM:  5720
SUBJECT:  WINGS - Stringer U-14 Reinforcement Interference with FQIS Tank Unit at Rib 21, Left
Hand
1. PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is applicable to 737-800 Airplanes modified to receive Split Scimitar Winglets
(SSW), with Blended or Split Scimitar Winglets installed as listed below (Refer to STC ST00830SE).
An equivalent change is on subsequent production airplanes.
Line Number  Variable Number  Serial Number
4928  YS655  42385
4935  YS656  60082
4942  YS657  36905
4949  YS277  39944
4953  YQ508  39076
4955  YS658  42522
4956  YS357  41445
4962  YS659  60083
4967  YS660  36898
4970  YQ509  39075
4974  YS661  42523
4975  YS358  41446
4989  YS278  39945
4999  YS663  60086
5001  YS664  60084
5011  YS665  60085
5014  YS359  44155
5022  YS666  42525
5030  YS667  42524
5032  YS668  35973
5038  YS669  36907
5042  YS670  36935
5044  YS671  42528
5045  YS279  36707
5059  YS360  44156
Original Issue: April 5, 2018  AP737-57-020
Page 6 of 17
Aviation Partners Boeing Proprietary

### Page 7 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
2. Spares Affected
None
B. Concurrent Requirements
None
C. Reason
This service bulletin gives instructions to inspect the Stringer U-14 reinforcement installation at Rib 21 on
the left hand wing to verify that there is sufficient clearance to the FQIS tank unit number 12.
If the clearance is less than required minimum, this service bulletin gives instructions to modify the
Stringer U-14 reinforcement angle to provide the required clearance.
If not corrected, the FQIS installation at this location would not be in compliance with 28-AWL-30 CDCCL.
An operator reported the first nonconformance during a 737-800-7 Split Scimitar Winglet modification.
The nonconformance involved the FQIS tank unit number 12 contacting the U-14 reinforcement angle.
The same operator reported another nonconformance on a second aircraft, which involved the FQIS tank
unit number 12 clearing the U-14 reinforcement angle by 0.05 inch.
APB resolved both discrepant conditions by providing instructions to trim the free flange of the
reinforcement angle to obtain minimum 0.10 inch clearance to the FQIS tank unit number 12. The MRR
dispositions met the 28-AWL-30 CDCCL requirement, which states the gap between the side of the tank
unit, and tank structure is 0.10 inch or more.
D. Description
This service bulletin gives instructions to do the following.
• Inspect the Stringer U-14 reinforcement installation at Rib 21 on the left hand wing to verify that
there is enough clearance to the FQIS tank unit number 12.
• Trim the Stringer U-14 detail adjacent to the FQIS tank unit at Rib 21 to provide the necessary
clearance.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
Model  Zone
737-800  532
Original Issue: April 5, 2018  AP737-57-020
Page 7 of 17
Aviation Partners Boeing Proprietary

### Page 8 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
E. Compliance
Aviation Partners Boeing recommends doing the inspection within 18 months after the original issue of
this Service Bulletin.
Do the required actions in accordance with Paragraph 3. Accomplishment Instructions.
Condition  Action  Compliance Time
(Whichever Occurs Later)
All airplanes  Do PART 1:  Within 18 months after the original issue date of this
Inspection Of FQIS  Service Bulletin.
Tank Unit
Clearance To
Stringer U-14
Reinforcement At
Rib 21, Left Hand
Condition 1:  Do PART 3: Return  Before further flight
Measured clearance  the Aircraft to
Serviceable
is 0.10 inches or
Condition
greater
Condition 2:  Do PART 2: Trim  Before further flight
Stringer U-14
is less than 0.10  Measured clearance  Provide Clearance  Reinforcement To
inches.  To FQIS Tank Unit
Do PART 3: Return
the Aircraft to
Service Condition
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on the
airplane being in its original Boeing delivery configuration when the SSW modification was performed.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
The changes given in this Service Bulletin are in compliance with the Airworthiness Limitation 28-AWL-
30. This service bulletin has been reviewed by the FAA Oversight Office for fuel tank ignition prevention
requirements and was found that the repair and modification maintain an acceptable level of safety. No
further approval from the FAA Oversight Office is required to satisfy the requirements of Boeing 737 MPD
D626A0010-9-04 CDCCL 28-AWL-30 provided the repair and modification are accomplished in
accordance with the instructions in this service bulletin.
Original Issue: April 5, 2018  AP737-57-020
Page 8 of 17
Aviation Partners Boeing Proprietary

### Page 9 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
G. Warranty Information
APB warranty reimbursement of labor and material costs is available for eligible airplanes. Please refer to
Paragraphs 1.H and 2.A.
H. Manpower
The table below shows an estimate of the task hours necessary to do this inspection for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
• Time to adjust to the workplace
• Time to schedule the work
• Time to inspect the work
Time to cure the materials
• Time to make the parts
• Time to find the tools.
APB will reimburse labor costs, based on the actual work performed. Total reimbursement will not
exceed the sum of hours from the table below. The labor rate will be in accordance with the APB Winglet
Sales agreement for the affected airplanes, if specified. If not otherwise specified, the labor rate will be
the reported actual rate if it is fair and reasonable.
Submit claims to APB Warranty (apbwarranty@aviationpartners.com) with supporting data, including
airplanes line number, work instruction Parts accomplished, total labor hours, labor rate, and total dollar
amount per airplane.
Task  Number of Persons  Man-Hours  Elapsed Time
(Hours)
Defuel and Purge  2  4  2
Tank - L/H
Open Fuel Cell  2  1  .5
Access Panels
Inspection  1  .25  .25
Remove Tank Unit  1  .25  .25
for Access
Repair  1  2  2
Reinstall Tank Unit  1
Test Tank Unit  2  1  .5
Close Fuel Cell  2  1  .5
Access Panels
Fuel Leak Check  1  .5  .5
TOTAL FOR EACH AIRPLANE  10.5  7
Return aircraft to Service condition
Original Issue: April 5, 2018  AP737-57-020
Page 9 of 17
Aviation Partners Boeing Proprietary

### Page 10 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
1. Weight and Balance Changes
None
J. Electrical Load Data
None
K. References
1. Existing Data:
a. D633A101 Boeing 737-600/700/800/900 Aircraft Maintenance Manual (AMM).
b. D634T210 Boeing 737-800 Structural Repair Manual (SRM).
c. Boeing Standard Overhaul Practice Manual (SOPM).
d. D626A001 Boeing 737-600/700/800/900 Maintenance Planning Document (MPD)
2. Data Supplied with This Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of This Service Bulletin:
Drawing Number Title
737-8360  Modification Insti - Str U-14 Reinforcement, Upper, Fwd, Inbd
This drawing was used to prepare this service bulletin. This drawing is not necessary to make the
specified changes, and is not supplied with this service bulletin. This drawing may not be applicable
to all airplane configurations or operators.
L. Other Publications Affected
1. None
2. Aviation Partners Boeing has evaluated the repairs and/or changes in this service bulletin for effects
on Fatigue Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required
in the Maintenance Program. This service bulletin affects FCS, but no new DTIs are necessary.
M. Interchangeability and Intermixability of Parts
See Paragraph 2.D. Existing Parts Accountability.
N. Software Accomplishment Summary
None
Original Issue: April 5, 2018  AP737-57-020
Page 10 of 17
Aviation Partners Boeing Proprietary

### Page 11 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
2. MATERIAL INFORMATION
A. Material - Price and Availability
Not Applicable.
B. Parts Necessary for Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator:
Material  Description  QTY  QTY
per Wing  per SS
BMS10-20 Type I|  Primer
Bonderite M-CR 600 Aero
Surface Treatment
(formerly Alodine 600)
* Quantity as required.
C. Parts Necessary to Change Spares
None
D. Existing Parts Accountability
None.
E. Special Tooling - Price and Availability
No special tooling is required to do repairs.
F. Special Tooling Necessary to Do This Service Bulletin
Maintenance and overhaul tools as specified in the maintenance manuals may be necessary. Examine
operator tool supply before starting work to make sure all necessary tools are available.
Original Issue: April 5, 2018  AP737-57-020
Page 11 of 17
Aviation Partners Boeing Proprietary

### Page 12 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
3. ACCOMPLISHMENT INSTRUCTIONS
A. General Notes
WARNING: IF ELECTRICAL POWER IS APPLIED TO THE AIRPLANE, MAKE SURE YOU OBEY ALL
PRECAUTIONS WHILE YOU DO WORK. IF YOU DO NOT OBEY THE PRECAUTIONS,
DEATH OR INJURY TO PERSONS, AND DAMAGE TO THE AIRPLANE CAN OCCUR.
WARNING: CAREFULLY DO ALL OF THE SAFETY PROCEDURES IN THE PURGING AND ENTRY
PROCEDURE OF THE FUEL TANK. INJURY TO PERSONS AND DAMAGE TO
EQUIPMENT CAN OCCUR.
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES, OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
CAUTION: ELECTRICALLY GROUND THE AIRPLANE. THIS WILL HELP TO PREVENT DAMAGE TO
THE AIRPLANE OR EQUIPMENT.
NOTE: 1. Obey all warnings and cautions given in the applicable sections of the Aircraft Maintenance
Manual (AMM).
2. Do functional tests and adjustments prior to returning the aircraft to service.
3. Unless shown differently, these dimensions and tolerances are used:
Linear dimensions are in inches.
Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus
0.03 inch.
Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch.
- Angular tolerance is plus or minus 2 degrees.
Torque limits to tighten nut and bolts are given in the 737 SRM, 51-40-04.
4. Make an entry into aircraft maintenance records once service bulletin is completed.
5. For approved material and process substitutions, refer to the 737 SRM, Chapter 51 or Boeing
drawing 65-88700.
These work instructions refer to procedures included in other Boeing documents. When the
words "refer to" are used and the operator has an accepted alternative procedure, the
accepted alternative procedure can be used. When the words "in accordance with" are
included in the instruction, the procedure in the document must be used.
7. If it is necessary to remove more parts for access, you can remove those parts. If you can
get access without removing identified parts, it is not necessary to remove all of the identified
parts. Jacking and shoring limitations must be obeyed.
8. Use of colors in Figures is based on guidance from the ATA e-Business Program (ATA)
S1000D.
9. The compliance times for the actions in Paragraph 3.B., Work Instructions are in Paragraph
1.E., Compliance.
Original Issue: April 5, 2018  AP737-57-020
Page 12 of 17
Aviation Partners Boeing Proprietary

### Page 13 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
B. Work Instructions
PART 1: INSPECTION OF FQIS TANK UNIT CLEARANCE TO STRINGER U-14 REINFORCEMENT AT
RIB 21, LEFT HAND
1. Remove electrical power from the airplane. Refer to the 737 AMM, 24-22-00 as an accepted
procedure.
2. Purge fuel tanks and prepare main tanks for entry. Refer to the 737 AMM, 28-11-00 as an
accepted procedure.
3. Remove and keep the following access panel. Refer to the 737 AMM, 28-11-11 as an accepted
procedure. (Reference FIGURE 1)
• Left Wing 532QB
4. Measure the minimum clearance between the FQIS tank unit installed on Rib 21 (WS 617.00)
and Stringer U-14 reinforcement as shown in FIGURE 2.
a. Condition 1 - If the measured clearance is 0.10 inches or greater, do the following:
(1) Do PART 3: Return the Aircraft to Serviceable Condition
b. Condition 2 - If the measured clearance is less than 0.10 inches, do the following:
(1) Do PART 2: Trim Stringer U-14 Reinforcement To Provide Clearance To FQIS Tank Unit
(2) Do PART 3: Put the Airplane Back to a Serviceable Condition
PART 2: REPAIR/TERMINATING ACTION - TRIM STRINGER U-14 REINFORCEMENT TO PROVIDE
CLEARANCE TO FQIS TANK UNIT.
1. Remove the FQIS Tank Unit installed on LH Rib 21. Refer to the 737 AMM, 28-41-21 as an
accepted procedure.
2. Trim the Stringer U-14 reinforcement as shown in Figure 2 to obtain the required clearance to the
FQIS tank unit.
a. Trim the minimum amount of material from the Stringer U-14 reinforcement to get 0.10
inches of clearance to the FQIS tank unit.
b. Ensure the minimum dimension requirements shown in Figure 2 are met.
c. Ensure trimmed edge has a surface finish of 125 micro inches Ra or smoother.
d. Break sharp edges of all repair parts to .003 to 0.020 inch radius
3. Flap peen trimmed edge. Intensity. 006A, coverage 2.0. Refer to SOPM 20-10-03 as an
accepted procedure.
4. Finish trimmed edge as follows;
a. Manually apply Bonderite M-CR 600 Aero to bare surfaces. Refer to SOPM 20-43-03 as an
accepted procedure.
b. Apply two coats of BMS10-20, Type II primer. Refer to the 737 AMM, 28-11-00 as an
accepted procedure.
5. Reinstall the FQIS Tank Unit on LH Rib 21 in accordance with the 737 AMM, 28-41-21.
Ensure that there is a 0.10 inches or greater clearance between the Stringer U-14
reinforcement and the FQIS tank unit.
Original Issue: April 5, 2018  AP737-57-020
Page 13 of 17
Aviation Partners Boeing Proprietary

### Page 14 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
PART 3: PUT THE AIRPLANE BACK TO A SERVICEABLE CONDITION.
1. If it is necessary, install the access panel for the fuel tank. Refer to the 737 AMM, 28-11-11 as an
accepted procedure
2. If it is necessary, Supply Electrical Power, Refer to the 737 AMM, 24-22-00 as an accepted
procedure.
3. Return the aircraft to a serviceable condition.
Original Issue: April 5, 2018  AP737-57-020
Page 14 of 17
Aviation Partners Boeing Proprietary

### Page 15 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
LEFT WING
CENTER
FUEL TANK
RIB 1  RIB 5
SIDE-OF-  (MAIN TANK WALL)
BODY
RIB 8
(BAFFLE RIB)
NO.1
FUEL TANK
RIB 22 (MAIN
200g0500350  TANK WALL)
532QB  RIB 25
(SURGE
TANK
END WALL)
W
LEFT WING
(BOTTOM VIEW)
INBO  FQIS Tank Unit
No. 12 (F12L)
SEE FIGURE 2
FIGURE 1: WING LOWER SURFACE
Original Issue: April 5, 2018  AP737-57-020
Page 15 of 17
Aviation Partners Boeing Proprietary

### Page 16 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
UPPER WING
STRINGER U-13.5  STRINGER U-14  SKIN
STRINGER U-14
REINFORCEMENT
FQIS TANK  WING RIB 21
UNIT
— 0.10 INCH CLEARANCE
MINIMUM
UP
View Looking Outboard
→ FWD
FIGURE 2: FQIS TANK UNIT No. 12 INSTALLATION AT RIB 21
(SHEET 1 OF 2)
Original Issue: April 5, 2018  AP737-57-020
Page 16 of 17
Aviation Partners Boeing Proprietary

### Page 17 (OCR)

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737-57-020
R 0.50 INCH  R 1.00 INCH
(2 PLACES)  MINIMUM
STRINGER
U-13.5  STRINGER U-14
FQIS TANK
UNIT
0.75 INCH
MINIMUM
WING RIB 21
STRINGER U-14
REINFORCEMENT
→ FWD
View Looking Up
OUTBD
FIGURE 2: FQIS TANK UNIT No. 12 INSTALLATION AT RIB 21
(SHEET 2 OF 2)
Original Issue: April 5, 2018  AP737-57-020
Page 17 of 17
Aviation Partners Boeing Proprietary

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
