# Aviation Partners Boeing Alert Service Bulletin AP737C-57-003

Copy: No revision named ("AP737C-57-003_IR_WINGS"), 20 pages: PDF https://openairdocs.org/files/sha256/7c/db/7cdbe54fb64ba6da50461b90a5c14c40c58d58440a33aed974b0444b75879a3d; text https://openairdocs.org/service-documents/aviation-partners-boeing/ap737c-57-003/file/7cdbe54fb64b.md. Rights: © Aviation Partners Boeing. Filed by the FAA in regulations.gov docket FAA-2020-0587; AD 2021-08-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Aviation Partners Boeing](https://openairdocs.org/service-documents/aviation-partners-boeing.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: AP737C-57-003
- Page: https://openairdocs.org/service-documents/aviation-partners-boeing/ap737c-57-003

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2021-08-12](https://openairdocs.org/ad/2021-08-12.md), effective May 28, 2021: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/aviation-partners-boeing/ap737c-57-003/proposed.md).

## Text (20 pages)

Rights: © Aviation Partners Boeing. Filed by the FAA in regulations.gov docket FAA-2020-0587; AD 2021-08-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

AVIATION PARTNERS BOEING SERVICE BULLETIN 
2811 S 102nd Street, Suite 200 
Seattle, WA 98168 
(206) 830-7699 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 3 of 22 
Aviation Partners Boeing Proprietary 
 ALERT      
NUMBER: AP737C-57-003  
Original Issue: July 28, 2020  
ATA SYSTEM: 5730  
SUBJECT: WINGS - Lower Outer Wing Skin - Aft Edge Inspection 
 
 
PROPRIETARY NOTICE 
The data contained hereon and herein is proprietary to Aviation Partners Boeing. Neither this data  nor the data 
contained herein shall be reproduced, used or disclosed to others without the written authorization of Aviation 
Partners Boeing. 
 
EXPORT CONTROLLED TECHNOLOGY 
This document contains information about a technology controlled by the Export Administration Regulations (EAR) 
(15 CFR 730-774). It has been classified under Export Control Classification Number (ECCN) 9E991 and may not 
be exported to certain countries without a license. Providing this information to a foreign national – inside or outside 
the United States – can constitute a prohibited export. Each person handling this document has a legal responsibility 
to comply with all applicable EAR requirements and should consult with an Export Control Officer before providing 
it to any foreign national.

### Page 2

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 4 of 22 
Aviation Partners Boeing Proprietary 
Table of Contents 
1. PLANNING INFORMATION .......................................................................................................................5 
A. Effectivity ....................................................................................................................................................5 
1. Airplanes .....................................................................................................................................................5 
2. Spares Affected ..........................................................................................................................................5 
B. Concurrent Requirements...........................................................................................................................5 
C. Reason........................................................................................................................................................5 
D. Description ..................................................................................................................................................6 
E. Compliance .................................................................................................................................................6 
F. Approval ................................................................................................................................................... 10 
G. Manpower ................................................................................................................................................ 10 
H. Weight and Balance Changes ................................................................................................................. 10 
I. Electrical Load Data ................................................................................................................................. 10 
J. References .............................................................................................................................................. 11 
1. Existing Data: ........................................................................................................................................... 11 
2. Data Supplied with this Service Bulletin: ................................................................................................. 11 
3. Installation Drawings Used in the Preparation of this Service Bulletin: ................................................... 11 
K. Publications Affected ............................................................................................................................... 11 
1. Publications ............................................................................................................................................. 11 
2. Damage Tolerance Based Structural Inspections: .................................................................................. 11 
L. Interchangeability and Intermixability of Parts ......................................................................................... 11 
M. Software Accomplishment Summary ....................................................................................................... 11 
2. MATERIAL INFORMATION..................................................................................................................... 11 
A. Material - Price and Availability ............................................................................................................... 11 
B. Industry Support Information ................................................................................................................... 11 
C. Parts Necessary for Each Airplane .......................................................................................................... 11 
1. Kits/Parts ................................................................................................................................................. 11 
2. Parts and Materials Supplied by the Operator: ....................................................................................... 11 
3. Parts Modified and Re-identified ............................................................................................................. 11 
4. Parts Removed and Not Replaced .......................................................................................................... 11 
D. Parts Necessary to Change Spares ........................................................................................................ 11 
E. Special Tooling – Price Availability .......................................................................................................... 12 
F. Special Tooling Necessary to do this Service Bulletin ............................................................................ 12 
3. ACCOMPLISHMENT INSTRUCTIONS ................................................................................................... 12 
A. GENERAL INFORMATION ..................................................................................................................... 12 
B. WORK INSTRUCTIONS .......................................................................................................................... 12 
 
APPENDIX A: COMPLIANCE TIME CALCULATION FOR GROUP 3 AIRPLANES  .............................................. 17 
APPENDIX B: HIGH FREQUENCY EDDY CURRENT (HFEC INSPECTION OF THE LOWER AFT WING SKIN, 
AFT EDGE AT FLAP TRACK NUMBER 1, 2, 3, 6, 7, AND 8 ATTACHMENT LOCATIONS  .............. 18

### Page 3

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 5 of 22 
Aviation Partners Boeing Proprietary 
1. PLANNING INFORMATION 
A. Effectivity 
RC: Start 
1. Airplanes 
This service bulletin is applicable to 737-300 Airplanes with Blended Winglets, and 737-500 Airplanes 
with Blended Winglets (Refer to STC ST01219SE). 
GROUP CONFIGURATION DESCRIPTION 
3 STC ST01219SE 
installed 737-300/-500 Airplanes 
Note: This service bulletin does not contain Group 1, Group 2, 737-400 (Group 3), or Group 4 airplanes. 
Group and Table designation in this service bulletin aligns with Boeing Service Bulletin 737 -57A1349, 
Original Issue, dated April 14, 2020. 
RC: End 
RC: Start 
2. Spares Affected 
None 
RC: End  
RC: Start 
B. Concurrent Requirements 
The service bulletin listed below must be done at the same time as this service bulletin:  
Company Service Bulletin Description 
The Boeing Company 737-57A1349, Original Issue, 
dated April 14, 2020 
Do a high frequency eddy current (HFEC) 
inspection of the left and right lower aft wing 
skin aft edge where the flap tracks attach to 
the track support fittings at flap track numbers 
1 (WBL 355), 2 (WBL 254), and 3 (WBL 191), 
and flap track numbers 6 (WBL 191), 7 (WBL 
254) and 8 (WBL 355), for any crack. If any 
crack is found, contact the Boeing Company 
for repair instructions, and do the repair. 
If no crack is found do a repeat HFEC 
inspection of the left and right wing, lower aft 
wing skin aft edge at flap track numbers 1 
(WBL 355), 2 (WBL 254), and 3 (WBL 191), 
and flap track numbers 6 (WBL 191), 7 (WBL 
254) and 8 (WBL 355), for any crack. 
RC: End 
C. Reason 
Accomplishment of this service bulletin will make sure any crack in the left and right wing, lower aft wing 
skin aft edge, where the flap tracks attach to the track support fittings, at flap track numbers 1 (WBL 355), 
2 (WBL 254), and 3 (WBL 191), and flap  track numbers 6 (WBL 191), 7 (WBL 254) and 8 (WBL 355), is 
found. If this bulletin is not done, an undetected crack in the lower aft wing skin could result in the inability 
of the structure to carry limit load and could adversely affect the structural integrity of the airplane.

### Page 4

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 6 of 22 
Aviation Partners Boeing Proprietary 
During teardown of a 737-300, crack indications were found in the lower aft wing skin bolt holes where 
the flap tracks attach to the track support fitting at flap track number 1, flap track number 2, and flap track 
number 3. Crack indications at flap track number 2 and flap track number 3 were confirmed by a 
metallurgical lab to have cracks. The indication at flap track number 1 was confirmed by the metallurgical 
lab to have some corrosion in the hole of the fitting, but no crack in the skin. This damage is the result of 
local stresses being higher than expected. The left and right wing, lower aft wing skin pad up length is 
insufficient to reduce stress. The crack finding occurred at 67,695 flight cycles / 80,269 flight hours.  
This service bulletin gives instructions to do a High Frequency Eddy Current (HFEC) inspection of the left 
and right wing, lower aft wing skin aft edge where the flap tracks attach to the track support fittings at flap 
track numbers 1 (WBL 355), 2 (WBL 254), and 3 (WBL 191), and flap track numbers 6 (WBL 191), 7 
(WBL 254) and 8 (WBL 355), for any crack. 
Boeing Service Related Problem (SRP) 737-SRP-57-0341 is related to this service bulletin. 
Boeing Fleet Team Digest (FTD) 737-FTD-57-18003 is related to this service bulletin. 
D. Description 
Do a high frequency eddy current (HFEC) inspection of the left and right lower aft wing skin aft edge 
where the flap tracks attach to the track support fittings at flap track numbers 1 (WBL 355), 2 (WBL 254), 
and 3 (WBL 191), and flap track numbers 6 (WBL 191), 7 (WBL 254) and 8 (WBL 355), for any crack. If 
any crack is found, contact the Boeing Company for repair instructions, and do the repair.  
If no crack is found do a repeat HFEC inspection of the left and right wing, lower aft w ing skin aft edge 
where the flap tracks attach to the track support fittings at flap track numbers 1 (WBL 355), 2 (WBL 254), 
and 3 (WBL 191), and flap track numbers 6 (WBL 191), 7 (WBL 254) and 8 (WBL 355),  for any crack. 
The work in this service bulletin is done in the maintenance zone(s) given below. 
Group 3: 
Affected Maintenance Zones 
Model Zone 
737-300/-500 with APB Blended 
Winglets 
307, 309, 407, 409 
RC: Start 
E. Compliance 
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive (AD) related to 
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this 
service bulletin mandatory. 
Accomplish the required action(s), based on the applicable condition(s) in Table 2, in accordance with the 
Accomplishment Instructions. 
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When 
more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION 
numbers for that CONDITION number or OPTION number.

### Page 5

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 7 of 22 
Aviation Partners Boeing Proprietary 
Group 3: 
Table 2: High Frequency Eddy Current (HFEC) inspection of the left and right wing, lower aft wing skin aft 
edge at attachment locations for flap track numbers 1, 2, 3, 6, 7, and 8 
Condition Action Compliance Time (Whichever Occurs 
Later) 
Repeat 
Interval 
(Not to 
Exceed) 
All Airplanes ACTION 1: Do a HFEC inspection 
of the lower aft wing skin, aft edge, 
at flap track number 1 (WBL 355) 
attachment location, for any crack. 
Before 𝑌 = 𝐵 + 15,000 ∗
(25,000−𝐵)
25,000  
B = Flight Cycles at STC 
Installation 
Y = Compliance Threshold with 
STC installed (Total Flight Cycles) 
Within 
4,500 
flight 
cycles 
after 
the 
original 
issue 
date of 
this 
service 
bulletin 
- 
ACTION 2: Do a HFEC inspection 
of the lower aft wing skin, aft edge, 
at flap track number 2 (WBL 254) 
attachment location, for any crack. 
Before 𝑌 = 𝐵 + 23,000 ∗
(25,000−𝐵)
25,000  
B = Flight Cycles at STC 
Installation 
Y = Compliance Threshold with 
STC installed (Total Flight Cycles) 
- 
ACTION 3: Do a HFEC inspection 
of the lower aft wing skin, aft edge, 
at flap track number 3 (WBL 191) 
attachment location, for any crack. 
Before 25,000 total flight cycles - 
ACTION 4: Do a HFEC inspection 
of the lower aft wing skin, aft edge, 
at flap track number 6 (WBL 191) 
attachment location, for any crack. 
Before 25,000 total flight cycles - 
ACTION 5: Do a HFEC inspection 
of the lower aft wing skin, aft edge, 
at flap track number 7 (WBL 254) 
attachment location, for any crack. 
Before 𝑌 = 𝐵 + 23,000 ∗
(25,000−𝐵)
25,000  
B = Flight Cycles at STC 
Installation 
Y = Compliance Threshold with 
STC installed (Total Flight Cycles) 
- 
ACTION 6: Do a HFEC inspection 
of the lower aft wing skin, aft edge, 
at flap track number 8 (WBL 355) 
attachment location, for any crack. 
Before 𝑌 = 𝐵 + 15,000 ∗
(25,000−𝐵)
25,000  
B = Flight Cycles at STC 
Installation 
Y = Compliance Threshold with 
STC installed (Total Flight Cycles) 
-

### Page 6

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 8 of 22 
Aviation Partners Boeing Proprietary 
Group 3: 
Table 2: High Frequency Eddy Current (HFEC) inspection of the left and right wing, lower aft wing skin aft 
edge at attachment locations for flap track numbers 1, 2, 3, 6, 7, and 8 
Condition Action Compliance 
Time 
(Whichever 
Occurs Later) 
Repeat Interval (Not 
to Exceed) 
CONDITION 1: NO 
CRACK FOUND AT FLAP 
TRACK NUMBER 1 (WBL 
355) ATTACHMENT 
LOCATION. (a) 
Do a repeat HFEC inspection of the lower aft 
wing skin, aft edge, flap track number 1 (WBL 
355) attachment location for any crack. 
- 4,000 flight cycles 
CONDITION 2: ANY 
CRACK FOUND AT FLAP 
TRACK NUMBER 1 (WBL 
355) ATTACHMENT 
LOCATION. (a) 
Contact The Boeing Company for repair 
instructions and do the repair. 
Before further 
flight 
- 
CONDITION 3: NO 
CRACK FOUND AT FLAP 
TRACK NUMBER 2 (WBL 
254) ATTACHMENT 
LOCATION. (a) 
Do a repeat HFEC inspection of the lower aft 
wing skin, aft edge, flap track number 2 (WBL 
254) attachment location for any crack. 
- 6,000 flight cycles 
CONDITION 4: ANY 
CRACK FOUND AT FLAP 
TRACK NUMBER 2 (WBL 
254) ATTACHMENT 
LOCATION. (a) 
Contact The Boeing Company for repair 
instructions and do the repair. 
Before further 
flight 
- 
CONDITION 5: NO 
CRACK FOUND AT FLAP 
TRACK NUMBER 3 (WBL 
191) ATTACHMENT 
LOCATION. (a) 
Do a repeat HFEC inspection of the lower aft 
wing skin, aft edge, flap track number 3 (WBL 
191) attachment location for any crack. 
- 5,500 flight cycles 
CONDITION 6: ANY 
CRACK FOUND AT FLAP 
TRACK NUMBER 3 (WBL 
191) ATTACHMENT 
LOCATION. (a) 
Contact The Boeing Company for repair 
instructions and do the repair. 
Before further 
flight 
-

### Page 7

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 9 of 22 
Aviation Partners Boeing Proprietary 
Group 3: 
Table 2: High Frequency Eddy Current (HFEC) inspection of the left and right wing, lower aft wing skin aft 
edge at attachment locations for flap track numbers 1, 2, 3, 6, 7, and 8 
Condition Action Compliance 
Time 
(Whichever 
Occurs Later) 
Repeat Interval (Not 
to Exceed) 
CONDITION 7: NO 
CRACK FOUND AT FLAP 
TRACK NUMBER 6 (WBL 
191) ATTACHMENT 
LOCATION. (a) 
Do a repeat HFEC inspection of the lower aft 
wing skin, aft edge, flap track number 6 (WBL 
191) attachment location for any crack. 
- 5,500 flight cycles 
CONDITION 8: ANY 
CRACK FOUND AT FLAP 
TRACK NUMBER 6 (WBL 
191) ATTACHMENT 
LOCATION. (a) 
Contact The Boeing Company for repair 
instructions and do the repair. 
Before further 
flight 
- 
CONDITION 9: NO 
CRACK FOUND AT FLAP 
TRACK NUMBER 7 (WBL 
254) ATTACHMENT 
LOCATION. (a) 
Do a repeat HFEC inspection of the lower aft 
wing skin, aft edge, flap track number 7 (WBL 
254) attachment location for any crack. 
- 6,000 flight cycles 
CONDITION 10: ANY 
CRACK FOUND AT FLAP 
TRACK NUMBER 7 (WBL 
254) ATTACHMENT 
LOCATION. (a) 
Contact The Boeing Company for repair 
instructions and do the repair. 
Before further 
flight 
- 
CONDITION 11: NO 
CRACK FOUND AT FLAP 
TRACK NUMBER 8 (WBL 
355) ATTACHMENT 
LOCATION. (a) 
Do a repeat HFEC inspection of the lower aft 
wing skin, aft edge, flap track number 8 (WBL 
355) attachment location for any crack. 
- 4,000 flight cycles 
CONDITION 12: ANY 
CRACK FOUND AT FLAP 
TRACK NUMBER 8 (WBL 
355) ATTACHMENT 
LOCATION. (a) 
Contact The Boeing Company for repair 
instructions and do the repair. 
Before further 
flight 
- 
(a) More than one CONDITION can be applicable on each airplane. 
RC: End

### Page 8

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 10 of 22 
Aviation Partners Boeing Proprietary 
F. Approval 
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in 
this service bulletin comply with the applicable regulations and are FAA approved. This service bulletin and 
its approval were based on the installation of APB STC ST01219SE. 
If an airplane has a non -Boeing modification, non-APB modification, or repair that affects a component or 
system also affected by this service bulletin, the operator is responsible for obtaining appropriate regulatory 
agency approval before incorporating this service bulletin. 
G. Manpower 
The table below shows an estimate of the task hours necessary to do this inspection for each airplane. This 
estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator task hour 
data if necessary. The estimate does not include lost time. These are some examples of lost time:  
 Time to adjust to the workplace 
 Time to schedule the work 
 Time to inspect the work 
 Time to cure the materials 
 Time to make the parts 
 Time to find the tools 
 
Task Number of Persons Task Hours Elapsed Hours 
Open Access 2 2.0 1.0 
FIGURE 1 1 0.5 0.5 
FIGURE 2 1 0.5 0.5 
FIGURE 3 1 0.5 0.5 
FIGURE 4 1 0.5 0.5 
FIGURE 5 1 0.5 0.5 
FIGURE 6 1 0.5 0.5 
Close Access 2 2.0 1.0 
TOTAL FOR EACH AIRPLANE 7.0 5.0 
 
H. Weight and Balance Changes 
Weight and Balance changes affected by incorporation of this service bulletin are dependent on the 
inspection, number of flight cycles, condition, type, number and location of repairs done on each 
particular airplane. Weight and Balance are to be calculated by the operator by weighing parts installed or 
removed. Operators should make necessary revisions to the appropriate weight and balanc e report. 
I. Electrical Load Data 
Not changed

### Page 9

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 11 of 22 
Aviation Partners Boeing Proprietary 
J. References 
1. Existing Data: 
a. Boeing Service Bulletin 737-57A1349 
b. Boeing Service Related Problem (SRP) 737-SRP-57-0341 
c. 737 Fleet Team Digest (FTD) 57-18003 
d. Boeing 737 Non-Destructive Testing (NDT) Manual Part 6, 51-00-00 
e. Boeing 737-300/400/500 Aircraft Maintenance Manual (AMM) 27-51-00, 27-51-71 
2. Data Supplied with this Service Bulletin: 
None. 
3. Installation Drawings Used in the Preparation of this Service Bulletin: 
Refer to Boeing Service Bulletin 737-57A1349. 
K. Publications Affected 
1. Publications 
None. 
2. Damage Tolerance Based Structural Inspections: 
This service bulletin affects Fatigue Critical Structure (FCS) but does not contain repairs or changes. 
L. Interchangeability and Intermixability of Parts 
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts. 
M. Software Accomplishment Summary 
Not affected. 
2. MATERIAL INFORMATION 
A. Material - Price and Availability 
None. 
B. Industry Support Information 
APB warranty remedies are not available for the inspection procedures given in this service bulletin. 
C. Parts Necessary for Each Airplane 
1. Kits/Parts 
None. 
2. Parts and Materials Supplied by the Operator: 
None. 
3. Parts Modified and Re-identified 
None. 
4. Parts Removed and Not Replaced 
None. 
D. Parts Necessary to Change Spares 
None

### Page 10

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 12 of 22 
Aviation Partners Boeing Proprietary 
E. Special Tooling – Price Availability 
None. 
F. Special Tooling Necessary to do this Service Bulletin 
Refer to Boeing Service Bulletin 737-57A1349. 
3. ACCOMPLISHMENT INSTRUCTIONS 
A. GENERAL INFORMATION 
Refer to Boeing Service Bulletin 737-57A1349. 
Some steps in the Work Instructions are labeled as Required for Compliance (RC). If this service bulletin is 
mandated by an Airworthiness Directive (AD), then the steps labeled as RC, including sub -steps under an 
RC step and any figures identified in an RC step, must be done to comply with the AD. If a step or sub-step 
is labeled “RC Exempt”, then the RC requirement is removed from that step or sub -step. An Alternative 
Method of Compliance (AMOC) is required for any deviations to RC steps , including sub -steps and 
identified figures. Steps not labeled as RC may be deviated from using accepted methods in accordance 
with the operator’s maintenance or inspection program without obtaining approval of an AMOC. This is 
provided that the RC steps,  including sub-steps and identified figures, can still be done as specified, and 
the airplane can be put back in an airworthy condition. 
B. WORK INSTRUCTIONS 
RC: Start 
Actions Required for Compliance: 
1. Requirements 
Group 3: 
Table 1: High Frequency Eddy Current (HFEC) inspection of the left and right wing, lower aft wing skin aft 
edge at attachment locations for flap track numbers 1, 2, 3, 6, 7, and 8 
Condition Action Method of Compliance Refer to the listed procedures in the 
service document at Original Issue as an 
accepted procedure 
All Airplanes ACTION 1: Do a HFEC 
inspection of the lower 
aft wing skin, aft edge, 
flap track number 1 
(WBL 355) attachment 
location for any crack. 
- Boeing SB 737-57A1349, Original Issue, 
dated April 14, 2020 
PART 1: OPEN ACCESS 
Boeing SB 
737-57A1349, Original 
Issue, dated April 14, 
2020 
FIGURE 1 
- 
ACTION 2: Do a HFEC 
inspection of the lower 
aft wing skin, aft edge, 
flap track number 2 
(WBL 254) attachment 
location for any crack. 
Boeing SB 
737-57A1349, Original 
Issue, dated April 14, 
2020 
FIGURE 2 
-

### Page 11

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 13 of 22 
Aviation Partners Boeing Proprietary 
Group 3: 
Table 1: High Frequency Eddy Current (HFEC) inspection of the left and right wing, lower aft wing skin aft 
edge at attachment locations for flap track numbers 1, 2, 3, 6, 7, and 8 
Condition Action Method of Compliance Refer to the listed procedures in the 
service document at Original Issue as an 
accepted procedure 
All Airplanes ACTION 3: Do a HFEC 
inspection of the lower 
aft wing skin, aft edge, 
flap track number 3 
(WBL 191) attachment 
location for any crack. 
Boeing SB 
737-57A1349, Original 
Issue, dated April 14, 
2020 
FIGURE 3 
- 
ACTION 4: Do a HFEC 
inspection of the lower 
aft wing skin, aft edge, 
flap track number 6 
(WBL 191) attachment 
location for any crack. 
Boeing SB 
737-57A1349, Original 
Issue, dated April 14, 
2020 
FIGURE 4 
- 
ACTION 5: Do a HFEC 
inspection of the lower 
aft wing skin, aft edge, 
flap track number 7 
(WBL 254) attachment 
location for any crack. 
Boeing SB 
737-57A1349, Original 
Issue, dated April 14, 
2020 
FIGURE 5 
- 
ACTION 6: Do a HFEC 
inspection of the lower 
aft wing skin, aft edge, 
flap track number 8 
(WBL 355) attachment 
location for any crack. 
Boeing SB 
737-57A1349, Original 
Issue, dated April 14, 
2020 
FIGURE 6 
-

### Page 12

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 14 of 22 
Aviation Partners Boeing Proprietary 
Group 3: 
Table 1: High Frequency Eddy Current (HFEC) inspection of the left and right wing, lower aft wing skin aft 
edge at attachment locations for flap track numbers 1, 2, 3, 6, 7, and 8 
Condition Action Method of Compliance Refer to the listed 
procedures in the 
service document 
at Original Issue as 
an accepted 
procedure 
CONDITION 1: NO 
CRACK FOUND AT FLAP 
TRACK NUMBER 1 (WBL 
355) ATTACHMENT 
LOCATION. (a) 
Do a repeat HFEC inspection of the 
lower aft wing skin, aft edge, flap 
track number 1 (WBL 355) 
attachment location for any crack. 
Boeing SB 737-57A1349, 
Original Issue, dated April 
14, 2020 
FIGURE 1 
- 
CONDITION 2: ANY 
CRACK FOUND AT FLAP 
TRACK NUMBER 1 (WBL 
355) ATTACHMENT 
LOCATION. (a) 
Contact The Boeing Company for 
repair instructions and do the repair. 
- - 
CONDITION 3: NO 
CRACK FOUND AT FLAP 
TRACK NUMBER 2 (WBL 
254) ATTACHMENT 
LOCATION. (a) 
Do a repeat HFEC inspection of the 
lower aft wing skin, aft edge, flap 
track number 2 (WBL 254) 
attachment location for any crack. 
Boeing SB 737-57A1349, 
Original Issue, dated April 
14, 2020 
FIGURE 2 
- 
CONDITION 4: ANY 
CRACK FOUND AT FLAP 
TRACK NUMBER 2 (WBL 
254) ATTACHMENT 
LOCATION. (a) 
Contact The Boeing Company for 
repair instructions and do the repair. 
- - 
CONDITION 5: NO 
CRACK FOUND AT FLAP 
TRACK NUMBER 3 (WBL 
191) ATTACHMENT 
LOCATION. (a) 
Do a repeat HFEC inspection of the 
lower aft wing skin, aft edge, flap 
track number 3 (WBL 191) 
attachment location for any crack. 
Boeing SB 737-57A1349, 
Original Issue, dated April 
14, 2020 
FIGURE 3 
- 
CONDITION 6: ANY 
CRACK FOUND AT FLAP 
TRACK NUMBER 3 (WBL 
191) ATTACHMENT 
LOCATION. (a) 
Contact The Boeing Company for 
repair instructions and do the repair. 
- -

### Page 13

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 15 of 22 
Aviation Partners Boeing Proprietary 
Group 3: 
Table 1: High Frequency Eddy Current (HFEC) inspection of the left and right wing, lower aft wing skin aft 
edge at attachment locations for flap track numbers 1, 2, 3, 6, 7, and 8 
Condition Action Method of Compliance Refer to the listed 
procedures in the 
service document 
at Original Issue as 
an accepted 
procedure 
CONDITION 7: NO 
CRACK FOUND AT FLAP 
TRACK NUMBER 6 (WBL 
191) ATTACHMENT 
LOCATION. (a) 
Do a repeat HFEC inspection of the 
lower aft wing skin, aft edge, flap 
track number 6 (WBL 191) 
attachment location for any crack. 
Boeing SB 737-57A1349, 
Original Issue, dated April 
14, 2020 
FIGURE 4 
- 
CONDITION 8: ANY 
CRACK FOUND AT FLAP 
TRACK NUMBER 6 (WBL 
191) ATTACHMENT 
LOCATION. (a) 
Contact The Boeing Company for 
repair instructions and do the repair. 
- - 
CONDITION 9: NO 
CRACK FOUND AT FLAP 
TRACK NUMBER 7 (WBL 
254) ATTACHMENT 
LOCATION. (a) 
Do a repeat HFEC inspection of the 
lower aft wing skin, aft edge, flap 
track number 7 (WBL 254) 
attachment location for any crack. 
Boeing SB 737-57A1349, 
Original Issue, dated April 
14, 2020 
FIGURE 5 
- 
CONDITION 10: ANY 
CRACK FOUND AT FLAP 
TRACK NUMBER 7 (WBL 
254) ATTACHMENT 
LOCATION. (a) 
Contact The Boeing Company for 
repair instructions and do the repair. 
- - 
CONDITION 11: NO 
CRACK FOUND AT FLAP 
TRACK NUMBER 8 (WBL 
355) ATTACHMENT 
LOCATION. (a) 
Do a repeat HFEC inspection of the 
lower aft wing skin, aft edge, flap 
track number 8 (WBL 355) 
attachment location for any crack. 
Boeing SB 737-57A1349, 
Original Issue, dated April 
14, 2020 
FIGURE 6 
Boeing SB 
737-57A1349, 
Original Issue, 
dated April 14, 2020 
PART 2: CLOSE 
ACCESS 
CONDITION 12: ANY 
CRACK FOUND AT FLAP 
TRACK NUMBER 8 (WBL 
355) ATTACHMENT 
LOCATION. (a) 
Contact The Boeing Company for 
repair instructions and do the repair. 
- Boeing SB 737-57A1349, 
Original Issue, 
dated April 14, 2020 
PART 2: CLOSE 
ACCESS 
(a) More than one CONDITION can be applicable on each airplane. 
 
 RC: End

### Page 14

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 16 of 22 
Aviation Partners Boeing Proprietary 
 
Procedures 
Group 3: 
1. Refer to Boeing Service Bulletin 737-57A1349 PART 1 for open access. 
2. Refer to Boeing Service Bulletin 737-57A1349 PART 2 for close access. 
3. Put the airplane back to a serviceable condition.

### Page 15

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 17 of 22 
Aviation Partners Boeing Proprietary 
This Appendix applies only to: Group 3 airplanes with STC ST01219SE installed. 
Compliance Time Calculation 
 
Flap Track # B 
(Airplane flight 
cycles at time of 
winglet STC 
initial 
installation 
T 
Basic Threshold 
(flight cycles) 
Q 
Usage Ratio 
Y 
(Compliance 
threshold in 
flight cycles) 
#1 / #8 B 15,000 (25,000 - B) / 
25,000 = B + T x Q #2 / #7 B 23,000 
EXAMPLE CALCULATION 
#1 / #8 20,000 15,000 0.20 23,000 
#2 / #7 20,000 23,000 0.20 24,600 
 
 
 
APPENDIX A: COMPLIANCE TIME CALCULATION FOR GROUP 3 AIRPLANES  
(SHEET 1 OF 1)

### Page 16

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 18 of 22 
Aviation Partners Boeing Proprietary 
This Appendix applies only to: Group 3 airplanes with STC ST01219SE installed. 
Logic diagrams are provided as an aid only. Information contained in Paragraph 1.E., Compliance is the primary  
source for compliance times. Information contained in Paragraph 3.B., Work Instructions is the primary source for 
tasks required for compliance. 
1. The table below gives the description for the parts and conditions called out in the logic diagrams.  
Title Description 
ACTION 1 DO A HFEC INSPECTION OF THE LOWER AFT WING SKIN, AFT EDGE, FLAP 
TRACK NUMBER 1 (WBL 355) ATTACHMENT LOCATION FOR ANY CRACK. 
ACTION 2 DO A HFEC INSPECTION OF THE LOWER AFT WING SKIN, AFT EDGE, FLAP 
TRACK NUMBER 2 (WBL 254) ATTACHMENT LOCATION FOR ANY CRACK.  
ACTION 3 DO A HFEC INSPECTION OF THE LOWER AFT WING SKIN, AFT EDGE, FLAP 
TRACK NUMBER 3 (WBL 191) ATTACHMENT LOCATION FOR ANY CRACK.  
ACTION 4 DO A HFEC INSPECTION OF THE LOWER AFT WING SKIN, AFT EDGE, FLAP 
TRACK NUMBER 6 (WBL 191) ATTACHMENT LOCATION FOR ANY CRACK.  
ACTION 5 DO A HFEC INSPECTION OF THE LOWER AFT WING SKIN, AFT EDGE, FLAP 
TRACK NUMBER 7 (WBL 254) ATTACHMENT LOCATION FOR ANY CRACK.  
ACTION 6 DO A HFEC INSPECTION OF THE LOWER AFT WING SKIN, AFT EDGE, FLAP 
TRACK NUMBER 8 (WBL 355) ATTACHMENT LOCATION FOR ANY CRACK.  
CONDITION 1 NO CRACK FOUND AT FLAP TRACK NUMBER 1 (WBL 355) ATTACHMENT 
LOCATION. 
CONDITION 2 ANY CRACK FOUND AT FLAP TRACK NUMBER 1 (WBL 355) ATTACHMENT 
LOCATION. 
CONDITION 3 NO CRACK FOUND AT FLAP TRACK NUMBER 2 (WBL 254) ATTACHMENT 
LOCATION. 
CONDITION 4 ANY CRACK FOUND AT FLAP TRACK NUMBER 2 (WBL 254) ATTACHMENT 
LOCATION. 
CONDITION 5 NO CRACK FOUND AT FLAP TRACK NUMBER 3 (WBL 191) ATTACHMENT 
LOCATION. 
CONDITION 6 ANY CRACK FOUND AT FLAP TRACK NUMBER 3 (WBL 191) ATTACHMENT 
LOCATION. 
CONDITION 7 NO CRACK FOUND AT FLAP TRACK NUMBER 6 (WBL 191) ATTACHMENT 
LOCATION. 
CONDITION 8 ANY CRACK FOUND AT FLAP TRACK NUMBER 6 (WBL 191) ATTACHMENT 
LOCATION. 
APPENDIX B: HIGH FREQUENCY EDDY CURRENT (HFEC INSPECTION OF THE LOWER AFT WING SKIN, 
AFT EDGE AT FLAP TRACK NUMBER 1, 2, 3, 6, 7, AND 8 ATTACHMENT LOCA TIONS 
(SHEET 1 OF 5)

### Page 17

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 19 of 22 
Aviation Partners Boeing Proprietary 
 
Title Description 
CONDITION 9 NO CRACK FOUND AT FLAP TRACK NUMBER 7 (WBL 254) ATTACHMENT 
LOCATION. 
CONDITION 10 ANY CRACK FOUND AT FLAP TRACK NUMBER 7 (WBL 254) ATTACHMENT 
LOCATION. 
CONDITION 11 NO CRACK FOUND AT FLAP TRACK NUMBER 8 (WBL 355) ATTACHMENT 
LOCATION. 
CONDITION 12 ANY CRACK FOUND AT FLAP TRACK NUMBER 8 (WBL 355) ATTACHMENT 
LOCATION. 
 
2. The table below gives the description for the flag notes called out in the logic diagram.  
Flag Note Letter Description 
(a) More than one CONDITION can be applicable to each airplane. 
 
APPENDIX B: HIGH FREQUENCY EDDY CURRENT (HFEC INSPECTION OF THE LOWER AFT WING 
SKIN, AFT EDGE AT FLAP TRACK NUMBER 1, 2, 3, 6, 7, AND 8 ATTACHMENT LOCATIONS  
(SHEET 2 OF 5)

### Page 18

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 20 of 22 
Aviation Partners Boeing Proprietary 
  
WHICHEVER OCCURS LATER 
 
WHICHEVER OCCURS LATER 
 
WHICHEVER OCCURS LATER 
 
Before 𝑌 = 𝐵 + 15,000 ∗
(25,000−𝐵)
25,000  
B = Flight Cycles at STC Installation 
Y = Compliance Threshold with STC 
installed (Total Flight Cycles) 
ACTION 1 
CONDITION 1 
(a) 
 CONDITION 2 
(a) 
NOT TO 
EXCEED 4,000 
FLIGHT CYCLES 
BEFORE 
FURTHER 
FLIGHT 
REPEAT HFEC 
INSPECTION OF 
THE LOWER AFT 
WING SKIN, AFT 
EDGE, FLAP 
TRACK NUMBER 
1 ATTACHMENT 
FOR ANY 
CRACK. 
CONTACT THE 
BOEING 
COMPANY FOR 
REPAIR 
INSTRUCTIONS, 
AND DO THE 
REPAIR. 
 
APPENDIX B: HIGH FREQUENCY EDDY CURRENT (HFEC INSPECTION OF THE LOWER AFT WING SKIN, AFT EDGE AT 
FLAP TRACK NUMBER 1, 2, 3, 6, 7, AND 8 ATTACHMENT LOCATIONS  
(SHEET 3 OF 5) 
 
WITHIN 4,500 FLIGHT CYCLES 
AFTER THE ORIGINAL ISSUE DATE 
OF THIS SERVICE BULLETIN 
WHICHEVER OCCURS LATER 
 
WHICHEVER OCCURS LATER 
 
WHICHEVER OCCURS LATER 
 
Before 𝑌 = 𝐵 + 23,000 ∗
(25,000−𝐵)
25,000  
B = Flight Cycles at STC Installation 
Y = Compliance Threshold with STC 
installed (Total Flight Cycles) 
ACTION 2 
NOT TO 
EXCEED 6,000 
FLIGHT CYCLES 
BEFORE 
FURTHER 
FLIGHT 
REPEAT HFEC 
INSPECTION OF 
THE LOWER AFT 
WING SKIN, AFT 
EDGE, FLAP 
TRACK NUMBER 
2 ATTACHMENT 
FOR ANY 
CRACK. 
CONTACT THE 
BOEING 
COMPANY FOR 
REPAIR 
INSTRUCTIONS, 
AND DO THE 
REPAIR. 
 
WITHIN 4,500 FLIGHT CYCLES 
AFTER THE ORIGINAL ISSUE DATE 
OF THIS SERVICE BULLETIN 
CONDITION 3 
(a) 
 CONDITION 4 
(a)

### Page 19

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 21 of 22 
Aviation Partners Boeing Proprietary 
  
WHICHEVER OCCURS LATER 
 
WHICHEVER OCCURS LATER 
 
WHICHEVER OCCURS LATER 
 
BEFORE 25,000 TOTAL FLIGHT 
CYCLES 
ACTION 3 
CONDITION 5 
(a) 
 CONDITION 6 
(a) 
NOT TO 
EXCEED 5,500 
FLIGHT CYCLES 
BEFORE 
FURTHER 
FLIGHT 
REPEAT HFEC 
INSPECTION OF 
THE LOWER AFT 
WING SKIN, AFT 
EDGE, FLAP 
TRACK NUMBER 
3 ATTACHMENT 
FOR ANY 
CRACK. 
CONTACT THE 
BOEING 
COMPANY FOR 
REPAIR 
INSTRUCTIONS, 
AND DO THE 
REPAIR. 
 
APPENDIX B: HIGH FREQUENCY EDDY CURRENT (HFEC INSPECTION OF THE LOWER AFT WING SKIN, AFT EDGE AT 
FLAP TRACK NUMBER 1, 2, 3, 6, 7, AND 8 ATTACHMENT LOCATIONS 
(SHEET 4 OF 5) 
 
WITHIN 4,500 FLIGHT CYCLES 
AFTER THE ORIGINAL ISSUE DATE 
OF THIS SERVICE BULLETIN 
WHICHEVER OCCURS LATER 
 
WHICHEVER OCCURS LATER 
 
WHICHEVER OCCURS LATER 
 
BEFORE 25,000 TOTAL FLIGHT 
CYCLES 
ACTION 4 
NOT TO 
EXCEED 5,500 
FLIGHT CYCLES 
BEFORE 
FURTHER 
FLIGHT 
REPEAT HFEC 
INSPECTION OF 
THE LOWER AFT 
WING SKIN, AFT 
EDGE, FLAP 
TRACK NUMBER 
6 ATTACHMENT 
FOR ANY 
CRACK. 
CONTACT THE 
BOEING 
COMPANY FOR 
REPAIR 
INSTRUCTIONS, 
AND DO THE 
REPAIR. 
 
WITHIN 4,500 FLIGHT CYCLES 
AFTER THE ORIGINAL ISSUE DATE 
OF THIS SERVICE BULLETIN 
CONDITION 7 
(a) 
 CONDITION 8 
(a)

### Page 20

AVIATION PARTNERS BOEING SERVICE BULLETIN AP737C-57-003 
 
Original Issue: July 28, 2020 AP737C-57-003 
 Page 22 of 22 
Aviation Partners Boeing Proprietary 
 
WHICHEVER OCCURS LATER 
 
WHICHEVER OCCURS LATER 
 
WHICHEVER OCCURS LATER 
 
Before 𝑌 = 𝐵 + 23,000 ∗
(25,000−𝐵)
25,000  
B = Flight Cycles at STC Installation 
Y = Compliance Threshold with STC 
installed (Total Flight Cycles) 
ACTION 5 
CONDITION 9 
(a) 
 CONDITION 10 
(a) 
NOT TO 
EXCEED 6,000 
FLIGHT CYCLES 
BEFORE 
FURTHER 
FLIGHT 
REPEAT HFEC 
INSPECTION OF 
THE LOWER AFT 
WING SKIN, AFT 
EDGE, FLAP 
TRACK NUMBER 
7 ATTACHMENT 
FOR ANY 
CRACK. 
CONTACT THE 
BOEING 
COMPANY FOR 
REPAIR 
INSTRUCTIONS, 
AND DO THE 
REPAIR. 
 
APPENDIX B: HIGH FREQUENCY EDDY CURRENT (HFEC INSPECTION OF THE LOWER AFT WING SKIN, AFT EDGE AT 
FLAP TRACK NUMBER 1, 2, 3, 6, 7, AND 8 ATTACHMENT LOCATIONS  
(SHEET 5 OF 5) 
 
WITHIN 4,500 FLIGHT CYCLES 
AFTER THE ORIGINAL ISSUE DATE 
OF THIS SERVICE BULLETIN 
WHICHEVER OCCURS LATER 
 
WHICHEVER OCCURS LATER 
 
WHICHEVER OCCURS LATER 
 
Before 𝑌 = 𝐵 + 15,000 ∗
(25,000−𝐵)
25,000  
B = Flight Cycles at STC Installation 
Y = Compliance Threshold with STC 
installed (Total Flight Cycles) 
ACTION 6 
NOT TO 
EXCEED 4,000 
FLIGHT CYCLES 
BEFORE 
FURTHER 
FLIGHT 
REPEAT HFEC 
INSPECTION OF 
THE LOWER AFT 
WING SKIN, AFT 
EDGE, FLAP 
TRACK NUMBER 
8 ATTACHMENT 
FOR ANY 
CRACK. 
CONTACT THE 
BOEING 
COMPANY FOR 
REPAIR 
INSTRUCTIONS, 
AND DO THE 
REPAIR. 
 
WITHIN 4,500 FLIGHT CYCLES 
AFTER THE ORIGINAL ISSUE DATE 
OF THIS SERVICE BULLETIN 
CONDITION 11 
(a) 
 CONDITION 12 
(a)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
