# Aviation Partners Boeing Service Bulletin AP767-57-010

## Copies (2)

Copies the FAA filed in AD dockets on regulations.gov, newest revision first. A newer revision may exist.

- Revision 14 ("AP767-57-010_R14"), 114 pages: PDF https://openairdocs.org/files/sha256/6f/ef/6fef3e95e3976f43b1d757e9689ef1371f3131bf98044ee517e550d0fce2b5a1; text https://openairdocs.org/service-documents/aviation-partners-boeing/ap767-57-010/file/6fef3e95e397.md. Rights: © Aviation Partners Boeing. Filed by the FAA in regulations.gov docket FAA-2026-0023; AD 2026-16-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- AP767-57-010 (11) WINGS - Lower Skin at Outboard Segment of Stringer L-9_5 - Inspection and Repair ("AP767-57-010 (11) WINGS - Lower Skin at Outboard Segment of Stringer L-9_5 - Inspection and Repair"), 111 pages: PDF https://openairdocs.org/files/sha256/e2/79/e279321bc928bd25cb0e6975e27b4dbd872802f2ad6d5a800853c017801eb699; text https://openairdocs.org/service-documents/aviation-partners-boeing/ap767-57-010/file/e279321bc928.md. Rights: © Aviation Partners Boeing. Filed by the FAA in regulations.gov docket FAA-2015-1421; AD 2018-11-14 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Aviation Partners Boeing](https://openairdocs.org/service-documents/aviation-partners-boeing.md)
- Type: Service bulletin (Service Bulletin)
- Number: AP767-57-010
- Latest revision known: AP767-57-010, Revision 14, dated November 17, 2025 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/aviation-partners-boeing/ap767-57-010

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2026-16-06](https://openairdocs.org/ad/2026-16-06.md), effective Sep 17, 2026: Revisions 11, 12, 13 and 14
- [AD 2018-11-14](https://openairdocs.org/ad/2018-11-14.md), effective Jul 10, 2018: Revision 11

Also cited in [2 proposed ADs](https://openairdocs.org/service-documents/aviation-partners-boeing/ap767-57-010/proposed.md).

## Text (114 pages)

Revision 14, the newest copy. Rights: © Aviation Partners Boeing. Filed by the FAA in regulations.gov docket FAA-2026-0023; AD 2026-16-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

AVIATION PARTNERS BOEING SERVICE BULLETIN 
555 Andover Park W., Suite 200 
Tukwila, WA 98188 
(206) 830-7699 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14:  November 17, 2025 Page i 
Aviation Partners Boeing PROPRIETARY 
NUMBER: AP767-57-010 Revision Transmittal Sheet 
Original Issue: October 23, 2013  
Revision 14: November 17, 2025  
ATA SYSTEM: 5720  
SUBJECT: WINGS - Lower Skin at Outboard Segment of Stringer L-9.5 between Wing Station 
990.2 and Wing Station 1046.2 - Inspection and Repair 
This revision includes all pages of the service bulletin. 
COMPLIANCE INFORMATION RELATED TO THIS REVISION 
Federal Aviation Administration (FAA) Airworthiness Directive AD 2018-11-14 is related to this service bulletin. 
Effects of this Revision on airplanes on which previous revision was done: NONE  
REASON FOR REVISION 
These sections were changed. 
Updated Table of Contents, List of Tables, List of Figures. 
1. Paragraph 1.A Effectivity, applicability clarification for 767-300/300F airplanes provisioned for Blended 
Winglets modified in accordance with STC ST01920SE, with or without winglets installed. Operators must 
comply with this service bulletin even if winglets have been removed from the aircraft.  
Paragraph 1.F Approval.  AP767-57-010 Revision 14 was Revision 13.

### Page 2

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14:  November 17, 2025 Page ii 
Aviation Partners Boeing PROPRIETARY 
REVISION HISTORY 
Original Issue: (Not published) October 23, 2013 
Revision 1: December 10, 2013 
Revision 2: January 23, 2014. 
Revision 3: (Not published) March 20, 2014 
Revision 4: April 22, 2014 
Revision 5: (Not published) July 11, 2014 
Revision 6: August 15, 2014 
Revision 7: November 4, 2014 
Revision 8: September 21, 2015 
Revision 9: December 29, 2015 
Revision 10: (Not published) September 20, 2016 
Revision 11: April 3, 2017 
Revision 12: June 21, 2018 
Revision 13: November 5, 2024 
Revision 14 November 17, 2025

### Page 3

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue:  October 23, 2013 AP767-57-010 
Revision 14: November 17, 2025 Page iii 
Aviation Partners Boeing PROPRIETARY 
APB DOCUMENT FEEDBACK FORM 
 
To provide feedback on this document to APB for corrections or improvements, 
please complete the form below and email to the attention of APB Liaison 
Engineering at: 
 
Email: leng@aviationpartners.com 
 
Airline Name: ______________________________________________ 
Contact Name: ______________________________________________ 
Phone Number: ______________________________________________ 
Email Address: ______________________________________________ 
Airplane Model-Type: ______________________________________________ 
Document Number: ______________________________________________ 
Document Revision: ______________________________________________ 
Document Title: ______________________________________________ 
Chapter-Section-
Subject: 
______________________________________________ 
Page: ______________________________________________ 
Page Date: ______________________________________________ 
Description of 
Change: 
(Include additional sheets as 
required) 
 
 
 
 
 
 
 
 
 
 
 
Attachments: ____________________________________________________

### Page 4

AVIATION PARTNERS BOEING SERVICE BULLETIN 
555 Andover Park W., Suite 200 
Tukwila, WA 98188 
(206) 830-7699 
Original Issue: October 23, 2013 AP767-57-010 
Revision 14: November 17, 2025 Page 1 of 111 
Aviation Partners Boeing PROPRIETARY 
 
NUMBER: AP767-57-010  
Original Issue: October 23, 2013  
Revision 14: November 17, 2025  
ATA SYSTEM: 5720 
SUBJECT: WINGS - Lower Skin at Outboard Segment of Stringer L-9.5 between Wing Station 
990.2 and Wing Station 1046.2 - Inspection and Repair 
 
PROPRIETARY NOTICE 
 
The data contained hereon and herein is proprietary to Aviation Partners Boeing. Neither this data nor 
the data contained herein shall be reproduced, used or disclosed to others without the written 
authorization of Aviation Partners Boeing. 
 
EXPORT CONTROLLED TECHNOLOGY 
 
This document contains information about a technology controlled by the Export Administration 
Regulations (EAR) (15 CFR 730-774). It has been classified under Export Control Classification 
Number (ECCN) 9E991 and may not be exported to certain countries without a license. Providing this 
information to a foreign national - inside or outside the United States - can constitute a prohibited 
export. Each person handling this document has a legal responsibility to comply with all applicable 
EAR requirements and should consult with an Export Control Officer before providing it to any foreign 
national.

### Page 5

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013 AP767-57-010 
Revision 14: November 17, 2025 Page 2 of 111 
Aviation Partners Boeing PROPRIETARY 
TABLE OF CONTENTS 
 
COMPLIANCE INFORMATION RELATED TO THIS REVISION ............................................................. i 
REASON FOR REVISION ........................................................................................................................ i 
REVISION HISTORY ................................................................................................................................ ii 
TABLE OF CONTENTS ........................................................................................................................... 2 
1. PLANNING INFORMATION ....................................................................................................... 5 
A. EFFECTIVITY ........................................................................................................................ 5 
B. CONCURRENT REQUIREMENTS........................................................................................ 6 
C. REASON ................................................................................................................................ 6 
D. CONFIGURATION DESCRIPTION ....................................................................................... 7 
E. COMPLIANCE...................................................................................................................... 14 
F. APPROVAL .......................................................................................................................... 21 
G. WARRANTY INFORMATION .............................................................................................. 21 
H. MANPOWER ........................................................................................................................ 22 
I. WEIGHT AND BALANCE CHANGES ................................................................................. 26 
J. ELECTRICAL LOAD DATA .................................................................................................. 26 
K. REFERENCES ..................................................................................................................... 26 
L. OTHER PUBLICATIONS AFFECTED ................................................................................. 28 
M. INTERCHANGEABILITY AND INTERMIXABILITY OF PARTS .......................................... 28 
2. MATERIAL INFORMATION ..................................................................................................... 29 
A. MATERIAL - PRICE AND AVAILABILITY ............................................................................ 29 
B. PARTS NECESSARY FOR EACH AIRPLANE ................................................................... 30 
C. PARTS NECESSARY TO CHANGE SPARES .................................................................... 46 
D. EXISTING PARTS ACCOUNTABILITY ............................................................................... 47 
E. SPECIAL TOOLING - PRICE AND AVAILABILITY ............................................................. 47 
F. SPECIAL TOOLING NECESSARY TO DO THIS SERVICE BULLETIN............................. 47 
3. ACCOMPLISHMENT INSTRUCTIONS ................................................................................... 48 
A. GENERAL NOTES ............................................................................................................... 48 
B. WORK INSTRUCTIONS ...................................................................................................... 50 
APPENDIX A: REPORTING INSTRUCTIONS: ................................................................................... 104 
APPENDIX B: LOGIC-BASED DIAGRAM OF WORK INSTRUCTIONS:............................................ 106 
APPENDIX C: PART FITUP FORCES: ............................................................................................... 111

### Page 6

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013 AP767-57-010 
Revision 14: November 17, 2025 Page 3 of 111 
Aviation Partners Boeing PROPRIETARY 
LIST OF TABLES 
Table 1 - Group 1 Airplane Effectivity ............................................................................................................................ 5 
Table 2 - Group 2 Airplane Effectivity ............................................................................................................................ 5 
Table 3 - Group 3 Airplane Effectivity ............................................................................................................................ 5 
Table 4 - Compliance Times for Lower Wing Skin Inspection and Corrective and Preventative Actions at 
Stringers L-9.5 - Group 1 and 2 ................................................................................................................... 14 
Table 5 - Compliance Times for Lower Wing Skin Inspection at Stringer L-9.5 and Corrective Actions - Group 3 .... 20 
Table 5a - Compliance Times for Individual Airplanes - Group 3 ................................................................................ 20 
Table 6 - Manpower ..................................................................................................................................................... 22 
Table 7a - Parts and Material List- Stringer L-9.5 Replacement & Stringer L-6.5 Modification Kit AP767-57-010-
01: ................................................................................................................................................................ 31 
Table 7b - Parts and Material List- Stringer L-9.5 Replacement & Stringer L-6.5 Modification Kit AP767-57-010-
02: ................................................................................................................................................................ 32 
Table 7c - Parts and Material List- Stringer L-9.5 Replacement & Stringer L-6.5 Modification Kit AP767-57-010-
03: ................................................................................................................................................................ 34 
Table 7d - Parts and Material List- Stringer L-9.5 Replacement & Stringer L-6.5 Modification Kit AP767-57-010-
04: ................................................................................................................................................................ 35 
Table 7e - Parts and Material List- Stringer L-9.5 Replacement & Stringer L-6.5 Modification Kit AP767-57-010-
05: ................................................................................................................................................................ 37 
Table 7f - Parts and Material List- Stringer L-9.5 Replacement & Stringer L-6.5 Modification Kit AP767-57-010-
07: ................................................................................................................................................................ 38 
Table 7g - Parts and Material List- Stringer L-9.5 Replacement & Modification Kit AP767-57-010-09: ...................... 40 
Table 7h - Additional parts required to rework -01 kit into -09 kit.  (Customer furnished) ........................................... 42 
Table 7i - Additional parts required to rework -02 kit into -09 kit.  (Customer furnished) ............................................ 43 
Table 7j - Additional parts required to rework -03 kit into -09 kit.  (Customer furnished) ............................................ 44 
Table 7k - Additional parts required to rework -04 kit into -09 kit.  (Customer furnished) ........................................... 45 
Table 8 - Existing Parts Accountability for Stringer L-9.5 Replacement ...................................................................... 47 
Table 9 - Stringer L-9.5 Fasteners ............................................................................................................................... 69 
Table 10 - External Doubler Fasteners ........................................................................................................................ 81 
Table 11 - External Doubler and Replacement Stringer Fasteners............................................................................. 97

### Page 7

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013 AP767-57-010 
Revision 14: November 17, 2025 Page 4 of 111 
Aviation Partners Boeing PROPRIETARY 
LIST OF FIGURES 
Figure 1: Lower Wing Skin - Outboard ............................................................................................................................ 10 
Figure 2: Group 1 and Group 2 - Lower Wing Skin - Outboard ....................................................................................... 11 
Figure 3: Wing Lower Surface ......................................................................................................................................... 12 
Figure 4: Left Wing Surge Tank Area .............................................................................................................................. 13 
Figure 5: Part 2: Hole Preparation ................................................................................................................................... 54 
Figure 6: Part 5: Terminating Action – Preventive Modification - Stringer L-9.5 ............................................................. 61 
Figure 7: Part 5: Terminating Action - Preventive Modification - Stringer L-9.5 .............................................................. 64 
Figure 8: Part 7: HFEC Inspection of Lower Outboard Wing Skin at Stringer L-9.5 (Sheet 1 of 2) ................................ 72 
Figure 9: Part 8: Repair Action  - Preventive Modification- External Doubler/Tripler, Filler at Stringer L-9.5 ................. 78 
Figure 10: Part 9: HFEC Inspection of Lower Outboard Wing Skin common to the External Doubler/Tripler Repair  .... 84 
Figure 11: Part 9: HFEC Inspection of Lower Outboard Wing Skin  around the periphery of the External Doubler  ....... 85 
Figure 12: Part 11: Repair Action - Preventive Modification  - External Doubler/Tripler, Filler and New Stringer at 
Stringer L-9.5 ................................................................................................................................................................... 91 
Figure 13: Part 12: HFEC Inspection of Lower Outboard Wing Skin Common to Stringer L -9.5  after Stringer 
Replacement Repair ...................................................................................................................................................... 100 
Figure 14: Part 13: HFEC Inspection of Lower Outboard Wing Skin  common to the External Doubler/Tripler Repair at 
Stringer L-9.5 ................................................................................................................................................................. 102 
Figure 15: Part 13: HFEC Inspection of Lower Outboard Wing Skin  around the periphery of the External Doubler at 
Stringer L-9.5 ................................................................................................................................................................. 103 
Figure A1: INSPECTION DATA – STRINGER L-9.5 ..................................................................................................... 104 
Figure B1: Group 1 and Group 2 - Diagram of Work Instructions (Sheet 1 of 3) .......................................................... 106 
Figure B2: Group 3 - Diagram of Work Instructions ...................................................................................................... 109 
Figure B3: Group 1 and Group 2  - Diagram of Work Instructions for Part 8 ................................................................ 110

### Page 8

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 5 of 111 
Aviation Partners Boeing PROPRIETARY 
1. PLANNING INFORMATION 
 
A. EFFECTIVITY 
1. This service bulletin is applicable to 767-300/300F airplanes provisioned 
for Blended Winglets modified in accordance with STC ST01920SE, with 
or without winglets installed. 
Operators must comply with this service bulletin even if winglets have 
been removed from the aircraft. 
Airplanes are identified as Group 1, Group 2, Group 3, or Group 4 
below. 
GROUP Description 
1 Airplanes with kit: 767-3000-1 thru -205 
2 Airplanes with kit: 767-3000-206 thru -209 
3 
Group 1 and 2 airplanes with Boeing repair installed prior 
to the original release of this service bulletin. External 
doubler installed common to the Lower Wing Skin between 
Stringer L-9 and Stringer L-10 at WSTA 990.2 RIB 31. 
4 Airplanes with kit: 767-3000-210 thru -225 
An equivalent change to this service bulletin has been incorporated in APB 
winglet retrofit kits for Group 4 airplanes. No more work is necessary on 
airplanes in Group 4. 
IDENTIFICATION BY LINE NUMBER, SERIAL NUMBER, AND VARIABLE 
NUMBER 
Table 1 - Group 1 Airplane Effectivity 
Deleted at Revision 8 
Table 2 - Group 2 Airplane Effectivity 
Deleted at Revision 8 
Table 3 - Group 3 Airplane Effectivity 
 
Line Number  Variable Number Serial Number 
698  VS131 29227 
712  VR251 25756 
729  VS133 29229 
778  VR256 29881 
806  VR257 30780 
848  VR259 32573 
860  VR260 30842 
940  VS901 34626 
985 VS924 37801

### Page 9

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 6 of 111 
Aviation Partners Boeing PROPRIETARY 
2. Spares Affected 
None. 
B. CONCURRENT REQUIREMENTS 
None. 
C. REASON 
This service bulletin gives instructions to detect and repair fatigue cracks in 
the lower wing skin. The fatigue cracks, if not corrected, could grow and 
lead to reduced load-carrying capability below ultimate load in the lower 
skin. The reduced load carrying capability in the lower skin could result in a 
wing structure failure and loss of control of airplane. Incorporating the 
modification in this service bulletin results in redistribution of the loads in the 
lower skin and prevents fatigue cracks. 
Fatigue cracks have been found in the lower wing skin at the farthest 
inboard fastener of stringer L-9.5 on some airplanes with winglets installed. 
The cracks were found at the fastener holes common to the inboard end of 
stringer L-9.5 between Wing Station 990.2 and Wing Station 1018.2 on the 
left- and right-hand wings. As of September 12, 2013, seven Model 767-300 
series airplanes have been found with cracks at stringer L-9.5. Four of the 
airplanes with cracks are (767-300F) freighters and three are (767-300) 
passenger airplanes. The affected airplanes have accumulated between 
2,800 and 4,800 flight cycles and between 16,000 and 26,000 flight hours 
since installation of APB 767 winglet systems 3.5 to 6 years ago. The 
reported crack lengths range from 0.100 to 0.492 inch long. The cracks 
were found with visual inspections along the lower wing skin and open hole 
HFEC inspections. No fuel leaks or additional damages were reported. APB 
analysis has determined the cracks to be a result of fatigue due to higher-
than-predicted fastener loads and skin stress peaking at the inboard end of 
stringers L-9.5. 
Subsequently cracks were found at the fastener holes common to the 
inboard end of stringer L-6.5 between Wing Station 990.2 and Wing Station 
1018.2 on the left- and right-hand wings. The cracks were found while the 
operators were doing the open hole HFEC inspections included in this 
service bulletin. As of April 20, 2016, 26 Model 767-300 series airplanes 
have been found with cracks at stringer L-6.5.  
Previously this service bulletin contained inspection, repair, and modification 
for stringer L-6.5 location. Recent analysis found that the modification for 
stringer L-6.5 given previously in this service bulletin was not sufficient to 
meet the 767 Design Service Objective. As the result of the new analysis 
and to make SB AP767-57-010 easier to understand, APB removed all work 
related to the stringer L-6.5 from SB AP767-57-010, and created a new 
service bulletin, SB AP767-57-014 for all work in the area of the stringer 
L-6.5.

### Page 10

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 7 of 111 
Aviation Partners Boeing PROPRIETARY 
In January 2016 two operators reported that cracks were found on lower 
wing skin common to the stringer L-9.5 inboard of rib 31. The cracks were 
found due to fuel leaks. Aviation Partners Boeing decided to create a new 
service bulletin, AP767-57-013, for stringer L-9.5 location inboard of Rib 31. 
See Figure 3 for the areas of works for this service bulletin and the related 
service bulletins AP767-57-013 and AP767-57-014. 
D. CONFIGURATION DESCRIPTION 
Group 1 and Group 2 Airplanes: 
This service bulletin gives instructions to do one of the following: 
• A repetitive high frequency eddy current (HFEC) inspection of the 
lower outboard skin external surface at the inboard end of stringer 
L-9.5 to detect cracks,  
OR  
• A repair action to remove the outboard stringer L-9.5 detail part and 
associated hardware, do an HFEC inspection of designated fastener 
holes, and installation of new stringer L-9.5. 
OR  
• A repair action to remove lower wing skin damage, installation of an 
external doubler, tripler and filler between stringer L-9 and L-10 and 
repetitive HFEC inspections of Lower Outboard Wing Skin common 
to the External Doubler/Tripler repair. 
OR  
• A repair action to remove the outboard stringer L-9.5 detail part and 
associated hardware, to install a new stringer L-9.5, to remove lower 
wing skin damage, and to install an external doubler, tripler and filler 
between stringer L-9 and L-10 and repetitive HFEC inspections of 
Lower Outboard Wing Skin common to the External Doubler/Tripler 
repair. 
Group 3 airplanes:   
Group 3 airplanes have installed an external doubler repair common to 
the wing lower skin between stringer L-9 and L-10 at WSTA 990.2 rib 31 
prior to the original release of this service bulletin. 
This service bulletin gives instructions to perform:  
• A repetitive internal HFEC inspection of the lower wing skin between 
stringers L-9 and L-9.5, and between stringers L-9.5 and L-10  
• A repetitive external HFEC inspection of lower outboard wing skin 
common to the external doubler repair.

### Page 11

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 8 of 111 
Aviation Partners Boeing PROPRIETARY 
Group 4 airplanes:  
An equivalent change to this service bulletin has been incorporated in 
APB winglet retrofit kits for Group 4 airplanes. No more work is 
necessary.

### Page 12

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 9 of 111 
Aviation Partners Boeing PROPRIETARY 
NOTE: Because of common access and common requirement to defuel 
and purge the fuel tanks for the modifications, it is easier to do the 
changes in other related service bulletins while the fuel tanks are 
open for access. APB recommends that operators examine service 
bulletins AP767-57-010, AP767-57-013, and AP767-57-014 and do 
all repair action modifications at the same time. 
The work in this service bulletin is done in the maintenance zones given 
below: 
Affected Maintenance Zones 
Model Zone 
767-300, 767-300F 541, 542, 641, 642 
See Figure 1 for area of work. 
See Figure 2 for area of inspections. 
See Figure 3 for detailed view of area of work. 
See Figure 4 for isometric view of area of work.

### Page 13

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 10 of 111 
Aviation Partners Boeing PROPRIETARY 
 
 
 
 
 
 
 
 
 
 
Figure 1: Lower Wing Skin - Outboard 
Left Wing Shown (Right Wing Opposite) 
INBD 
FWD 
UP 
AREA OF WORK - SURGE 
TANK, LOWER WING SKIN 
BETWEEN RIB 30 AND RIB 34, 
LEFT AND RIGHT WINGS

### Page 14

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 11 of 111 
 
Aviation Partners Boeing PROPRIETARY 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 2: Group 1 and Group 2 - Lower Wing Skin - Outboard 
Left Wing Shown (Right Wing Opposite) 
View Looking Up  
 
WSTA 
1018.2 
REF 
DO AN HFEC INSPECTION 
FOR CRACKS AT THE 
FASTENER HOLES COMMON 
TO THE LOWER WING SKIN 
AND STRINGER L-9.5 
STR L-9 
STR L-9.5 
STR L-10 
FWD 
OUTBD 
REFERENCE SLAT CAN 
DRAIN HOLE 
WSTA 
990.2 
REF

### Page 15

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 12 of 111 
 
Aviation Partners Boeing PROPRIETARY 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 3: Wing Lower Surface 
Left Wing Shown (Right Wing Opposite) 
  
OUTBD 
FWD 
542BB 
642BB 
542AB 
642AB 
542CB 
642CB 
(Access required for 
Part 5 or Part 11) 
 541XB 
641XB 
(Access required for 
part 8 or Part 11) 
Stringer L-9.5 Inbd 
Refer to SB AP767-57-013 
Stringer L-6.5 
Refer to SB AP767-57-014 
Stringer L-9.5 Outbd 
This Service Bulletin 
RIB 32 
RIB 33 
WSTA 
1046.2 
WSTA 
1018.2 
RIB 31 
(Tank 
End Rib) 
WSTA 
990.2 
RIB 30 
WSTA 
962.2 
RIB 29 
WSTA 
934.2 
RIB 28 
WSTA 
906.2 
RIB 27 
WSTA 
879.2 
View Looking 
Down 
Front 
Spar 
Rear 
Spar

### Page 16

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 13 of 111 
 
Aviation Partners Boeing PROPRIETARY 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 4: Left Wing Surge Tank Area 
(NOTE: For clarity, the upper skin, rear spar, and Rib 33 are not shown.) 
INBD 
FWD 
UP 
Front Spar 
Rib 32 WSTA 1018.20 
(Upper splice not shown) 
Rib 31 
WSTA 990.20 
Stringer L-9.5 
Stringer L-6.5 
Lower Wing Skin 
Slat Can 
Fuel Vent Duct

### Page 17

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 14 of 111 
 
Aviation Partners Boeing PROPRIETARY 
E. COMPLIANCE 
Federal Aviation Administration (FAA) Airworthiness Directive AD 2018-11-
14 is related to this service bulletin.  The effective date of AD 2018-11-14 is 
July 10, 2018. 
Aviation Partners Boeing recommends doing the preventive modification of 
outboard stringer L-9.5 at the operator's next scheduled maintenance visit 
that falls within the Compliance Times given in the Tables that follow. 
Alternatively, Aviation Partners Boeing recommends the installation of an 
external Doubler and Tripler at stringer L-9.5 at the operator's next 
scheduled maintenance visit that falls within the Compliance Times given in 
the Tables that follow. Do the HFEC inspection and the preventive 
modification before the thresholds shown in Table 4 or Table 5. 
 
Group 1 and Group 2 Airplanes: 
Table 4 - Compliance Times for Lower Wing Skin Inspection and Corrective 
and Preventative Actions at Stringers L-9.5 - Group 1 and 2 
NOTE:  The following conditions, times, and intervals are on a per wing basis. 
 
Condition Action Compliance Time 
 
Repeat 
Interval 
(Not more 
than) 
All airplanes Do PART 1: HFEC 
Inspection of Lower 
Outboard Wing Skin 
external surface – 
Stringer L-9.5 in 
accordance with 
Paragraph 3.B. Work 
Instructions. 
Before 1,500 flight cycles since 
installation of the winglet 
OR 
Before 7,500 flight hours since 
installation of the winglet 
OR 
Within 18 months after the 
effective date of AD 2018-11-
14  
(whichever occurs latest) 
-

### Page 18

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 15 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 4 (Continued) 
Condition Action Compliance Time 
(whichever occurs later) 
Repeat 
Interval 
(Not more 
than) 
Condition 1 - 
for airplanes 
on which 
Part 1 HFEC 
inspections 
was done 
and no crack 
was found at 
any hole. 
Option 1 Do PART 1: HFEC Inspection 
of Lower Outboard Wing Skin 
external surface – Stringer L-
9.5 in accordance with 
Paragraph 3.B. Work 
Instructions. 
- 1,500 flight 
cycles 
OR 
7,500 flight 
hours  
(whichever 
occurs first) 
Option 2 Do PART 2: Hole Preparation  
Do PART 3[1] – Plug Zero- 
Timed Holes in Wing Skin, 
Do PART 4[1] – Plug Open  
Holes in Lower Wing Skin, 
AND 
Do PART 5[1] – Repair Action  
– Preventive Modification – 
Stringer L-9.5, 
in accordance with Paragraph 
3.B. Work Instructions. 
Before further flight - 
Do PART 12: HFEC 
Inspection of Lower Outboard 
Wing Skin Common to 
Stringer L-9.5 
in accordance with Paragraph 
3.B. Work Instructions. 
Before 
25,000 total 
flight cycles 
OR 
Before 
90,000 total 
flight hours,  
whichever 
occurs first. 
Within 6,000 
flight cycles 
since the 
PART 5 
repair 
OR 
Within 
18,000 flight 
hours since 
the PART 5 
repair, 
whichever 
occurs first. 
6,000 flight 
cycles 
OR 
18,000 flight 
hours, 
whichever 
occurs first. 
[1] If the result of Part 2, Step 8 is Condition 3, obey the instructions for condition 3 and do  
not do Parts 3 thru 5.

### Page 19

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 16 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 4 (Continued) 
Condition Action Compliance Time 
(whichever occurs 
later) 
Repeat Interval 
(Not more than) 
Condition 1 
(Continued) 
Option 3 Do PART 8: Repair 
Action - Preventive 
Modification - External 
Doubler/Tripler, Filler 
at Stringer L-9.5 
Before further flight - 
Do PART 9: HFEC 
Inspection of Lower 
Outboard Wing Skin 
Common to the 
External 
Doubler/Tripler Repair 
at Stringer L-9.5  
in accordance with 
Paragraph 3.B. Work 
Instructions. 
Before 30,000 total  
flight cycles  
OR  
Before 90,000 total 
flight hours  
whichever occurs  
first 
[2] 
12,000 flight cycles  
OR 
36,000 flight hours, 
whichever occurs first, for 
internal HFEC inspection 
3,000 flight cycles  
OR 
9,000 flight hours, 
whichever occurs first, for 
external HFEC inspection 
Option 4  
(An 
alternative to 
Option 3 if 
Stringer 
replacement 
is necessary) 
Do PART 11: Repair 
Action - Preventive 
Modification - External 
Doubler/Tripler, Filler 
and new Stringer at 
Stringer L-9.5 
Before further flight - 
Do PART 13: HFEC 
Inspection of Lower 
Outboard Wing Skin 
Common to the 
External 
Doubler/Tripler Repair 
at Stringer L-9.5 in 
accordance with 
Paragraph 3.B. Work 
Instructions. 
Before 30,000 total  
flight cycles   
OR  
Before 90,000 total 
flight hours   
whichever occurs  
first 
[2]  
12,000 flight cycles  
OR 
36,000 flight hours, 
whichever occurs first, for 
internal HFEC inspection 
3,000 flight cycles  
OR 
9,000 flight hours, 
whichever occurs first, for 
external HFEC inspection 
[2] If airplane has accumulated more than 30,000 flight cycles or 90,000 flight hours at time of PART 8 
or PART 11 repair action, then use the repeat interval values for the inspection compliance time.

### Page 20

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 17 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 4 (Continued) 
Condition Action Compliance Time 
(whichever occurs 
later) 
Repeat Interval 
(Not more than) 
Condition 2 - 
for airplanes 
on which 
Part 1 HFEC 
inspections 
were done 
and any 
crack(s) 
were found 
in one or 
more 
affected 
fastener. 
Option 1 Do PART 8: Repair 
Action - Preventive 
Modification - 
External 
Doubler/Tripler, Filler 
at Stringer L-9.5 
Before further flight - 
Do PART 9: HFEC 
Inspection of Lower 
Outboard Wing Skin 
Common to the 
External 
Doubler/Tripler 
Repair at Stringer 
L-9.5  
in accordance with 
Paragraph 3.B. Work 
Instructions. 
Before 30,000 total 
flight cycles 
OR 
Before 90,000 total 
flight hours 
whichever occurs 
first 
[2] 
12,000 flight cycles  
OR 
36,000 flight hours, 
whichever occurs first, for 
internal HFEC inspection 
3,000 flight cycles  
OR 
9,000 flight hours, 
whichever occurs first, for 
external HFEC inspection 
Option 2 
(An 
alternative 
to Option 1 
if Stringer 
replacement 
is 
necessary) 
Do PART 11: Repair 
Action - Preventive 
Modification - 
External 
Doubler/Tripler, Filler 
and new Stringer at 
Stringer L-9.5 
Before further flight - 
Do PART 13: HFEC 
Inspection of Lower 
Outboard Wing Skin 
Common to the 
External 
Doubler/Tripler 
Repair at Stringer 
L-9.5  
in accordance with 
Paragraph 3.B. Work 
Instructions. 
Before 30,000 total 
flight cycles 
OR 
Before 90,000 total 
flight hours 
whichever occurs 
first 
[2] 
12,000 flight cycles  
OR 
36,000 flight hours, 
whichever occurs first, for 
internal HFEC inspection 
3,000 flight cycles  
OR 
9,000 flight hours, 
whichever occurs first, for 
external HFEC inspection 
[2] If airplane has accumulated more than 30,000 flight cycles or 90,000 flight hours at time of PART 8 
or PART 11 repair action, then use the repeat interval values for the inspection compliance time.

### Page 21

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 18 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 4 (Continued) 
Condition Action Compliance Time 
(whichever 
occurs later) 
Repeat Interval 
(Not more than) 
Condition 3 
— for 
airplanes on 
which Part 2 
Step 7 zero-
timing was 
done: Any 
crack(s) 
found on any 
of the five 
holes after 
oversizing to 
0.288 inch 
diameter or 
larger. 
Option 1 Do PART 8: Repair  
Action - Preventive 
Modification - External 
Doubler/Tripler, Filler 
at Stringer L-9.5 
Before further flight - 
Do PART 9: HFEC 
Inspection of Lower 
Outboard Wing Skin 
Common to the 
External 
Doubler/Tripler Repair 
at Stringer L-9.5  
in accordance with 
Paragraph 3.B. Work 
Instructions. 
Before 30,000 total 
flight cycles  
OR  
Before 90,000 total 
flight hours 
whichever occurs 
first 
[2] 
12,000 flight cycles  
OR 
36,000 flight hours, 
whichever occurs first, for 
internal HFEC inspection 
3,000 flight cycles  
OR 
9,000 flight hours, 
whichever occurs first, for 
external HFEC inspection 
Option 2 
(An 
alternative 
to Option 1 
if Stringer 
replacement 
is 
necessary) 
Do PART 11: Repair  
Action - Preventive 
Modification - External 
Doubler/Tripler, Filler 
and new Stringer at 
Stringer L-9.5 
Before further flight - 
Do PART 13: HFEC 
Inspection of Lower 
Outboard Wing Skin 
Common to the 
External 
Doubler/Tripler Repair 
at Stringer L-9.5  
in accordance with 
Paragraph 3.B. Work 
Instructions. 
Before 30,000 total 
flight cycles  
OR  
Before 90,000 total 
flight hours 
whichever occurs 
first 
[2] 
12,000 flight cycles  
OR 
36,000 flight hours, 
whichever occurs first, for 
internal HFEC inspection 
3,000 flight cycles  
OR 
9,000 flight hours, 
whichever occurs first, for 
external HFEC inspection 
[2] If airplane has accumulated more than 30,000 flight cycles or 90,000 flight hours at time of PART 8 
or PART 11 repair action, then use the repeat interval values for the inspection compliance time.

### Page 22

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 19 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 4 (Continued) 
Condition Action Compliance Time 
(whichever occurs 
later) 
Repeat Interval 
(Not more than) 
Condition 4 — for airplanes 
on which Part 8 Step 9 or 
Part 11 Step 10 HFEC 
inspection was done:  Any 
crack(s) found at trimmed 
edge of cutout equal to or 
larger than 3.34 inch by 
2.12 inch. 
Contact The Boeing 
Company for repair 
instructions and do 
the repair. 
Before further flight -

### Page 23

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 20 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Group 3 Airplanes: 
Table 5 - Compliance Times for Lower Wing Skin Inspection at Stringer L-9.5 
and Corrective Actions - Group 3 
NOTE:  The following conditions, times, and intervals are on a per wing basis. 
Condition Action Compliance 
Time 
Repeat Interval 
(Not more than) 
All airplanes Do PART 7: Internal and 
External HFEC Inspection of 
Lower Outboard Wing Skin 
common to the external doubler 
repair at Stringer L-9.5 in 
accordance with Paragraph 
3.B. Work Instructions. 
See Table 
5a. 
 
- 
Condition 5 — for 
airplanes on which Part 7 
internal and external HFEC 
inspections were done:  No 
crack(s) found at any hole. 
 
Do PART 7: Internal and 
External HFEC Inspection of 
Lower Outboard Wing Skin 
common to the external doubler 
repair at Stringer L-9.5 in 
accordance with Paragraph 
3.B. Work Instructions. 
-  12,000 flight 
cycles 
OR 
36,000 flight 
hours 
(whichever 
occurs first) 
Condition 6 — for 
airplanes on which Part 7 
internal and external HFEC 
inspections were done and 
any crack was found 
Contact The Boeing Company 
for repair instructions and do 
the repair. 
Before 
further flight 
- 
 
Table 5a - Compliance Times for Individual Airplanes - Group 3 
Line Number Serial Number Variable Number Compliance Time (whichever occurs first) Total Flight cycles Total Flight hours  
698 29227 VS131 28,000 109,000 
729 29229 VS133 29,000 111,000 
940 34626 VS901 21,000 76,000 
712 25756 VR251 21,000 89,000 
806 30780 VR257 25,000 92,000 
848 32573 VR259 25,000 79,000 
860 30842 VR260 22,000 79,000 
778 29881 VR256 24,000 93,000 
985 37801 VS924 15,000 54,000

### Page 24

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 21 of 111 
 
Aviation Partners Boeing PROPRIETARY 
 
F. APPROVAL 
This service bulletin has been examined by the Federal Aviation 
Administration (FAA). The changes specified herein comply with the 
applicable code of Federal Regulations (CFRs) and are FAA approved. This 
service bulletin and its approval were based on the airplane as modified by 
APB winglet retrofit in accordance with STC No. ST01920SE. 
If an airplane has any other non -Boeing modification or repair that affects a 
component or system also affected by this service bulletin, the operator is 
responsible for obtaining appropriate regulatory agency approval before 
incorporating this service bulletin. 
The changes given in this Service Bulletin are in compliance with the 
Airworthiness Limitation 28-AWL-08 as mandated by AD 2008-11-01 R1. This 
service bulletin has been reviewed by the FAA Oversight Office for fuel tank 
ignition prevention requirements and was found that the repair and modification 
maintain an acceptable level of safety.  No further approval from the FAA 
Oversight Offic e is required to satisfy the requirements of Boeing 767 MPD 
D622T001 CDCCL 28 -AWL-08 provided the repair and modification a re 
accomplished in accordance with the instructions in this service bulletin. 
The manager of the FAA West Certification Branch approves the inspections 
and corrective actions defined in service bulletin AP767 -57-010, Revision 14, 
as an Alternate Method of Compliance (AMOC) to the requirements of 
paragraph (g) of AD 2018-11-14. All provisions of AD 2018-11-14 that are not 
specifically referenced above remain fully applicable and must be complied 
with accordingly. 
 
G. WARRANTY INFORMATION 
Aviation Partners Boeing will no longer be accepting warranty claims for 
labor, material, or any other related costs as a result of this service bulletin 
beginning October 23, 2021. For additional information, refer to APB Service 
Letter APBSLWTY-0001.

### Page 25

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 22 of 111 
 
Aviation Partners Boeing PROPRIETARY 
H. MANPOWER 
The table below shows an estimate for the man-hours necessary to 
accomplish this service bulletin for each airplanes. This estimate is for direct 
labor only, done by experienced personnel. This estimate does not include 
lost time. These are some examples of lost time: 
• Time to adjust to the workplace. 
• Time to schedule the work. 
• Time to inspect the work. 
• Time to cure the materials. 
• Time to make the parts. 
• Time to find the tools. 
• Time to de-fuel and purge fuel tanks. 
• Time to access areas of airplanes (ladders, lifts, scaffolding, etc...) 
• Time to deactivate and activate electrical power of the airplane 
Table 6 - Manpower 
PART 1: HFEC INSPECTION OF LOWER OUTBOARD WING SKIN 
EXTERNAL SURFACE – STRINGER L-9.5 
Task Number of 
Persons 
Man-Hours Elapsed Time 
(Hours) 
Inspection 2 1 0.5 
TOTAL FOR EACH SHIPSET 1 0.5

### Page 26

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 23 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 6 - Manpower (Continued) 
PART 2: HOLE PREPARATION 
Task Number of 
Persons 
Man-Hours Elapsed Time 
(Hours) 
Access 2 10 5 
Remove Slat 
Can Drain Line 
2 2 1 
Remove Fuel 
Vent Tubes 
2 2 1 
Remove Stringer 
L-9.5 
2 32 16 
Zero-Time Holes 2 3 1.5 
TOTAL FOR EACH SHIPSET 49 24.5 
 
PART 3: PLUG ZERO-TIMED HOLES IN WING SKIN  
Task Number of 
Persons 
Man-Hours Elapsed Time 
(Hours) 
Rework (10) 
Holes 
2 4 2 
TOTAL FOR EACH SHIPSET 4 2

### Page 27

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 24 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 6 - Manpower (Continued) 
PART 4: PLUG OPEN HOLES IN LOWER WING SKIN  
Task Number of 
Persons 
Man-Hours Elapsed Time 
(Hours) 
Plug (24) Holes 2 10 5 
TOTAL FOR EACH SHIPSET 10 5 
 
PART 5: REPAIR ACTION – PREVENTIVE MODIFICATION – STRINGER L-
9.5  
Task Number of 
Persons 
Man-Hours Elapsed Time 
(Hours) 
Preventive 
Modification - 
Stringer L-9.5 
4 128 32 
TOTAL FOR EACH SHIPSET 128 32

### Page 28

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 25 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 6 - Manpower (Continued) 
PART 6: CLOSE ACCESS AFTER PREVENTIVE MODIFICATION AND 
REPLACEMENT 
Task Number of 
Persons 
Man-Hours Elapsed Time 
(Hours) 
Close Access 1–4 
1-2 
40 (internal mod) 
20 (external mod) 
20 
Test 2 4 2 
Paint Lower Wing 1 4 4 
TOTAL FOR EACH SHIPSET 48 (internal mod) 
28 (external 
mod) 
26 
PART 8: REPAIR ACTION - PREVENTIVE MODIFICATION - EXTERNAL 
DOUBLER/TRIPLER, FILLER AT STRINGER L-9.5  
Task Number of 
Persons 
Man-Hours Elapsed Time 
(Hours) 
Preventive 
Modification - 
External Doubler 
4 48 12 
TOTAL FOR EACH SHIPSET 48  12 
PART 11: REPAIR ACTION - PREVENTIVE MODIFICATION - EXTERNAL 
DOUBLER/TRIPLER, FILLER AND NEW STRINGER AT STRINGER L-9.5 
Task Number of 
Persons 
Man-Hours Elapsed Time 
(Hours) 
Preventive 
Modification - 
External Doubler 
/Tripler, Filler and 
New Stringer 
4 148 37 
TOTAL FOR EACH SHIPSET 148 37

### Page 29

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 26 of 111 
 
Aviation Partners Boeing PROPRIETARY 
 
I. WEIGHT AND BALANCE CHANGES 
Group 1 and 2 Airplanes 
Airplane 
SB Accomplishment 
Parts Contributing to 
W&B Change 
Change in 
Weight 
(Pounds) 
Change in 
Moment 
(Pound-Inch) 
767-300/-300F 
Internal Modification Part 5 -5.4 -7390 
767-300/-300F 
External Modification Part 8 +4.7 +6720 
767-300/-300F 
Internal and External 
Modification 
Part 11 -2.1 -2430 
767‐300/-300F 
 One Wing Internal and 
One Wing External 
Modification 
(Part 5+ Part 8)/2 -0.4 -340 
767‐300/-300F 
 One Wing External and 
One Wing Internal and 
External Modification 
(Part 8+ Part 11)/2 +1.3 +2140 
767‐300/-300F 
 One Wing Internal and 
One Wing Internal and 
External Modification 
(Part 5+ Part 11)/2 -3.8 -4910 
 
J. ELECTRICAL LOAD DATA 
Not changed. 
 
K. REFERENCES 
1. Existing Data: 
a. APB Service Bulletin AP767-57-013 and AP767-57-014 
b. D633T(xxx) Boeing 767-300 Aircraft Maintenance Manual (AMM).(xxx) 
Refers to customer specific code, 24-22-00, 28-11-00, 28-11-03, 28-11-11, 
28-13-00, 28-26-00.

### Page 30

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 27 of 111 
 
Aviation Partners Boeing PROPRIETARY 
c. D634T210 Boeing 767-300 Structural Repair Manual (SRM), Chapter 51, 51-
00-06, 51-10-01, 51-10-02, 51-20-05, 51-20-07, 51-40-02, 51-40-04, 51-40-
05, 51-40-08. 
d. D634T215 Boeing 767-300F SRM, Chapter 51, 51-00-06, 51-10-01, 51-10-
02, 51-20-05, 51-20-07, 51-40-04, 51-40-05, 51-40-08. 
e. D634T301 Boeing 767 Nondestructive Test Manual, 51-00-01, 51-00-16, 51-
00-19. 
f. Boeing Standard Overhaul Practice Manual (SOPM), 20-10-03, 20-30-03, 
20-43-03, 20-44-04, 20-50-10, 20-50-11, 20-50-20. 
g. AP67.3-0600 APB 767 Aircraft Maintenance Manual (AMM) Supplement, 28-
11-00 
h. AP67.3-0602 APB 767 SRM Supplement. 
i. AP67-0604.1 APB 767 Maintenance Planning Data and Structural Inspection 
Planning Data 767-300 (MPD) Supplement. 
2. Data Supplied with This Service Bulletin: 
None 
3. Installation Drawings Used in the Preparation of This Service Bulletin: 
Drawing Number Title 
767-3320 Rib Mod Installation - Rib 32, WSTA 1018.20 
767-3420 Stringer Installation - Lower L9.5 
 
These drawings were used to prepare this service bulletin. These 
drawings are not necessary to make the specified changes, and are not 
supplied with this service bulletin. These drawings may not be applicable 
to all airplane configurations or operators.

### Page 31

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 28 of 111 
 
Aviation Partners Boeing PROPRIETARY 
L. OTHER PUBLICATIONS AFFECTED 
1. Publications 
Publication Chapter / Section 
AP67.3-0602, Structural Repair Manual 57-20-03 
AP67.3-0603-APB, Weight and Balance 
Control and Loading  
1-86-001 
AP67.3-0604.2-DTR, Supplement to 
D622T001-DTR 767DTR Check Form 
Document for 767-300/-300F/-300BCF with 
Blended Winglets 
57-20-33D, 57-20-34B, 
57-20-34C, 57-20-34F, 
57-20-34H, 
57-20-I15AA, 
57-20-I15AA.2 
AP67.3-0802, Instructions for Continued 
Airworthiness 
All, updated format 
NOTE: * See paragraph 1.L.2 below for the structural inspection affected by 
this service bulletin. 
2. Damage Tolerance Based Structural Inspections: 
APB has evaluated the repairs and/or changes in this service bulletin for 
effects on Fatigue Critical Structure (FCS) and for changes to Damage 
Tolerance Inspections (DTI) required in the Maintenance Program. This 
service bulletin affects FCS and changes to DTI were necessary. The 
changes to DTI have been incorporated into the Maintenance Planning Data 
Supplement, AP67.3-0604.2-DTR. 
After incorporation of the repair described in PART 8 or PART 11 of this 
service bulletin, external LFEC inspection (direction 4) in DTR form 57-20-
I15AA in AP67.3-0604.2 is no longer possible in the area between Rib 30 
and Rib 31. The internal inspection in direction 1 or 2 in the DTR form 57-
20-I15AA shall be used to achieve required DTR. 
 
M. INTERCHANGEABILITY AND INTERMIXABILITY OF PARTS 
See paragraph 2.D. EXISTING PARTS ACCOUNTABILITY.

### Page 32

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 29 of 111 
 
Aviation Partners Boeing PROPRIETARY 
2. MATERIAL INFORMATION 
 
A. MATERIAL - PRICE AND AVAILABILITY 
 
The appropriate dash numbered kit(s) should be ordered based on the planned or 
anticipated repair/rework approach.  
The -09 Kit contains the material required for both the internal and external rework 
or repair related to stringer L-9.5 for group 1 and 2 airplanes and thus provides 
flexibility for either approach based on the aircraft owner/operator’s preference 
and/or inspection results. (Parts 3 through 5 or Part 8) This kit contains more parts 
than necessary depending on repair options selected by operator. Dispose of 
unused parts according to site procedures. 
If already received, the -01, -02, -03 or -04 kit may be used as an alternative to the 
-09 kit. The additional hardware described in Tables 7g, 7h, 7i or 7j, may be 
required to supplement the -01, -02, -03 or -04 kits depending on repair options 
selected by operator. 
If already received, the -05 Kit contains material required for the internal rework 
related to stringer L-6.5 for group 3 airplanes. Aviation Partners Boeing decided to 
remove the modification to stringer L-6.5 from this service bulletin. Dispose of this 
kit according to site procedures. 
If already received, the -07 Kit contains the material required for both the internal 
and external rework or repair related to stringer L-9.5 and the rework or repair 
related to stringer L-6.5 for group 1 and 2 airplanes. And thus this kit contains 
more parts than necessary. Dispose of unused parts according to site procedures.

### Page 33

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 30 of 111 
 
Aviation Partners Boeing PROPRIETARY 
B. PARTS NECESSARY FOR EACH AIRPLANE 
1. Kits/Parts:  
Parts and materials supplied as kits are shown in Table 7. The current kit is -09. All 
future orders should be for -09 kit. You can substitute -07 kit for -09 kit. -07 kit 
contains more parts than necessary. 
New kits 
Group 1 and 2 Airplanes 
Kit Number Name Description 
AP767-57-010-09 Lower Skin Panel Internal 
and External Components 
Rework Kit 
Stringer L-9.5 Material and Hardware, 
External Doubler/Tripler Material and 
Hardware 
Kits for the previous versions of this service bulletin 
Group 1 and 2 Airplanes 
Kit Number Name Description 
AP767-57-010-01 
(Superseded by 
AP767-57-010-07) 
Lower Skin Panel Internal 
Components Only Rework 
Kit 
Stringer L-9.5 Material and Hardware, 
Stringer L-6.5 Hardware 
AP767-57-010-02 
(Superseded by 
AP767-57-010-07) 
Lower Skin Panel Internal 
and External Components 
Rework Kit 
Stringer L-9.5 Material and Hardware, 
Stringer L-6.5 Hardware, External 
Doubler/Tripler Material and Hardware 
 
Kit Number Name Description 
AP767-57-010-03 
(Superseded by 
AP767-57-010-07) 
Lower Skin Panel Internal 
Components Only Rework 
Kit 
Stringer L-9.5 Material and Hardware, 
Stringer L-6.5 Hardware 
AP767-57-010-04 
(Superseded by 
AP767-57-010-07) 
Lower Skin Panel Internal 
and External Components 
Rework Kit 
Stringer L-9.5 Material and Hardware, 
Stringer L-6.5 Hardware, External 
Doubler/Tripler Material and Hardware 
 
Kit Number Name Description 
AP767-57-010-07 Lower Skin Panel Internal 
and External Components 
Rework Kit 
Stringer L-9.5 Material and Hardware, 
Stringer L-6.5 Hardware, External 
Doubler/Tripler Material and Hardware 
Group 3 Airplanes 
Kit Number Name Description 
AP767-57-010-05 Lower Skin Panel Internal 
Components Only Rework 
Kit for Group 3 Airplanes 
Stringer L-6.5 Hardware

### Page 34

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 31 of 111 
 
Aviation Partners Boeing PROPRIETARY 
 
Table 7a - Parts and Material List- Stringer L-9.5 Replacement & Stringer L-6.5 
Modification Kit AP767-57-010-01: 
AP767-57-010-01: Lower Skin Panel Internal Components Only Rework Kit 
(Superseded by AP767-57-010-07) 
 
Material Description QTY Per Wing QTY Per SS 
767-3421-7 Stringer – L-9.5, Detail 1 1 
767-3421-8 Stringer – L-9.5, Detail 1 1 
BACF3F016J103AF Filler 1 2 
BACF3F016G125AF Filler 1 2 
BACS40R013C019F Shim 1 2 
BACS40R019C024F Shim 1 2 
BACS40R019C026F Shim 1 2 
BACS40R019C087F Shim 1 2 
BACS40R024C025F Shim 1 2 
BACS40R024C043F Shim 1 2 
BACB30NW8K4X Bolt – Oversize 2 4 
BACB30NW8K5X Bolt – Oversize 5 10 
BACB30NW8K6X Bolt – Oversize 7 14 
BACB30NW8K7X Bolt – Oversize 3 6 
BACB30NW8K9X Bolt – Oversize 7 14 
BACB30NW8K10X Bolt – Oversize 4 8 
BACB30NW8K11X Bolt – Oversize 6 12 
BACB30NW10K13X Bolt – Oversize 6 12 
BACN10YT4CD Nut 19 38 
BACC30M10 Collar 6 12 
BACC30M8 Collar 15 30 
BACR15BA8D6C 
ON1 Rivet 5 10 
BACR15BA9D6C 
ON1 Rivet 5 10 
BACR15BA10D11C 
ON1 Rivet 7 14 
BACR15BA10D7C 
ON1 Rivet 5 10 
BACR15BA11D7C 
ON1 Rivet 5 10 
BACR15BA11D11C 
ON1 Rivet 7 14 
BACB30WQ5K5L 
ON2 Bolt – Radius Lead-in 2 4 
BACN10TN5K 
ON2 Nut 2 4

### Page 35

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 32 of 111 
 
Aviation Partners Boeing PROPRIETARY 
 
Table 7b - Parts and Material List- Stringer L-9.5 Replacement & Stringer L-6.5 
Modification Kit AP767-57-010-02: 
AP767-57-010-02: Lower Skin Panel Internal and External Components Rework Kit 
(Superseded by AP767-57-010-07) 
 
Material Description QTY Per Wing QTY Per SS 
767-3421-7 Stringer – L-9.5, Detail 1 1 
767-3421-8 Stringer – L-9.5, Detail 1 1 
BACF3F016J103AF Filler 1 2 
BACF3F016G125AF Filler 1 2 
BACS40R013C019F Shim 1 2 
BACS40R019C024F Shim 1 2 
BACS40R019C026F Shim 1 2 
BACS40R019C087F Shim 1 2 
BACS40R024C025F Shim 1 2 
BACS40R024C043F Shim 1 2 
BACB30NW8K4X Bolt – Oversize 2 4 
BACB30NW8K9X Bolt – Oversize 7 14 
BACB30NW8K11X Bolt – Oversize 9 18 
BACB30NW10K13X Bolt – Oversize 6 12 
BACC30M10 Collar 6 12 
BACR15BA8D6C 
ON1 Rivet 5 10 
BACR15BA10D7C 
ON1 Rivet 5 10 
BACR15BA11D7C 
ON1 Rivet 5 10 
BACR15BA11D11C 
ON1 Rivet 7 14 
BACR15BA10D11C 
ON1 Rivet 7 14 
2024-T3 Bare Sheet per AMS-
QQ-A-250/4 
(shot peen all over per BAC-
5730, .004A - .007A, coverage 
1 automated or 2 manual) 
Apply chemical corrosion 
coating to bare surfaces. Apply 
two coats of BMS 10-79, Type 
II primer. Refer to SOPM 20-41-
02; Part mark. Refer to SOPM 
20-50-10. 
Doubler** 
.080 x 10 x 25 1 2

### Page 36

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 33 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 7b (Continued)  
Material Description QTY Per Wing QTY Per SS 
2024-T3 Bare Sheet per AMS-
QQ-A-250/4 
(shot peen all over per BAC-
5730, .004A - .007A, coverage 
1 automated or 2 manual) 
 Apply chemical corrosion 
coating to bare surfaces. Apply 
two coats of BMS 10-79, Type 
II primer. Refer to SOPM 20-41-
02; Part mark. Refer to SOPM 
20-50-10. 
Tripler** 
.080 x 10 x 20 1 2 
2024-T3 Bare Sheet per AMS-
QQ-A-250/4 
Apply chemical corrosion 
coating to bare surfaces. Apply 
two coats of BMS 10-20, Type 
II primer. Refer to SOPM 20-41-
02; Part mark. Refer to SOPM 
20-50-10. 
Filler 
.100 x 2.2 x 3.6 1 2 
BACB30NW6K9Y Bolt – Oversize 3 6 
BACB30NW6K12Y Bolt – Oversize 1 2 
BACB30NW8K5X Bolt – Oversize 8 16 
BACB30NW8K6X Bolt – Oversize 10 20 
BACB30NW8K7X Bolt – Oversize 32 64 
BACB30NW8K8X Bolt – Oversize 24 48 
BACB30NW8K8Y Bolt – Oversize 2 4 
BACB30NW8K10X Bolt – Oversize 9 18 
BACB30NW8K12X Bolt – Oversize 1 2 
BACB30YP8K3 Bolt 3 6 
BACB30YP8K4 Bolt 8 16 
BACB30WQ5K5L 
ON2 Bolt – Radius Lead-in 2 4 
BACN10YT3CD Nut 4 8 
BACN10YT4CD Nut 90 180 
BACN10TN5K 
ON2 Nut 2 4 
BACC30BL8 Collar 11 22 
BACC30M8 Collar 15 30 
 
** Material dimension includes excess, trim as required 
ON1 BACR15BA()AD()C or BACR15GF()D() optional to BACR15BA()D()C. 
ON2 BACB30WQ5K6L + BACN10HY5M + BACW10AT35AS + BACW10AT35AS  
Optional to BACB30WQ5K5L + BACN10TN5K.

### Page 37

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 34 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 7c - Parts and Material List- Stringer L-9.5 Replacement & Stringer L-6.5 
Modification Kit AP767-57-010-03: 
AP767-57-010-03: Lower Skin Panel Internal Components Only Rework Kit 
(Superseded by AP767-57-010-07) 
 
Material Description QTY per Wing QTY per SS 
767-3421-7 Stringer – L-9.5, Detail 1 1 
767-3421-8 Stringer – L-9.5, Detail 1 1 
BACF3F016J103AF Filler 1 2 
BACF3F016G125AF Filler 1 2 
BACS40R013C019F Shim 1 2 
BACS40R019C024F Shim 1 2 
BACS40R019C026F Shim 1 2 
BACS40R019C087F Shim 1 2 
BACS40R024C025F Shim 1 2 
BACS40R024C043F Shim 1 2 
BACB30NW8K4X Bolt – Oversize 2 4 
BACB30NW8K5X Bolt – Oversize 5 10 
BACB30NW8K6X Bolt – Oversize 7 14 
BACB30NW8K7X Bolt – Oversize 3 6 
BACB30NW8K9X Bolt – Oversize 7 14 
BACB30NW8K10X Bolt – Oversize 4 8 
BACB30NW8K11X Bolt – Oversize 6 12 
BACB30NW8K13X Bolt – Oversize 1 2 
BACB30NW10K13X Bolt – Oversize 5 10 
BACN10YT4CD Nut 20 40 
BACC30M10 Collar 5 10 
BACC30M8 Collar 15 30 
BACR15BA8D6C 
ON1 Rivet 5 10 
BACR15BA9D6C 
ON1 Rivet 5 10 
BACR15BA10D11C 
ON1 Rivet 7 14 
BACR15BA10D7C 
ON1 Rivet 5 10 
BACR15BA11D7C 
ON1 Rivet 5 10 
BACR15BA11D11C 
ON1 Rivet 7 14 
BACB30WQ5K5L 
ON2 Bolt – Radius Lead-in 2 4 
BACN10TN5K 
ON2 Nut 2 4

### Page 38

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 35 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 7d - Parts and Material List- Stringer L-9.5 Replacement & Stringer L-6.5 
Modification Kit AP767-57-010-04: 
AP767-57-010-04: Lower Skin Panel Internal and External Components Rework Kit 
(Superseded by AP767-57-010-07) 
 
Material Description QTY per Wing QTY Per SS 
767-3421-7 Stringer – L-9.5, Detail 1 1 
767-3421-8 Stringer – L-9.5, Detail 1 1 
BACF3F016J103AF Filler 1 2 
BACF3F016G125AF Filler 1 2 
BACS40R013C019F Shim 1 2 
BACS40R019C024F Shim 1 2 
BACS40R019C026F Shim 1 2 
BACS40R019C087F Shim 1 2 
BACS40R024C025F Shim 1 2 
BACS40R024C043F Shim 1 2 
BACB30NW8K4X Bolt – Oversize 2 4 
BACB30NW8K9X Bolt – Oversize 7 14 
BACB30NW8K11X Bolt – Oversize 9 18 
BACB30NW8K13X Bolt – Oversize 1 2 
BACB30NW10K13X Bolt – Oversize 5 10 
BACC30M10 Collar 5 10 
BACR15BA8D6C ON1 Rivet 5 10 
BACR15BA9D6C ON1 Rivet 5 10 
BACR15BA10D7C ON1 Rivet 5 10 
BACR15BA11D7C ON1 Rivet 5 10 
BACR15BA11D11C ON1 Rivet 7 14 
BACR15BA10D11C ON1 Rivet 7 14 
2024-T3 Bare Sheet per AMS-QQ-A-
250/4 
(Shot peen all over, .004A - .007A, 
coverage 1 automated or 2 manual. Refer 
to SOPM 20-10-03) 
Check flatness by placing the part on a 
flat table. If a gap exists after application 
of limited localized force permitted by 
Appendix C, the part must be 
straightened by additional peening. 
Apply chemical conversion coating. Refer 
to SOPM 20-43-03. 
Apply two coats of BMS10-79, Type II 
primer. Refer to SOPM 20-44-04. 
Part mark. Refer to SOPM 20-50-10.  
Doubler** 
.080 x 10 x 25 1 2

### Page 39

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 36 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 7d (Continued)  
Material Description QTY per Wing QTY Per SS 
2024-T3 Bare Sheet per AMS-QQ-A-
250/4 
(Shot peen all over, .004A - .007A, 
coverage 1 automated or 2 manual. Refer 
to SOPM 20-10-03) 
Check flatness by placing the part on a 
flat table. If a gap exists after application 
of limited localized force permitted by 
Appendix C, the part must be 
straightened by additional peening. 
Apply chemical conversion coating. Refer 
to SOPM 20-43-03. 
Apply two coats of BMS10-79, Type II 
primer. Refer to SOPM 20-44-04. 
Part mark. Refer to SOPM 20-50-10. 
Tripler** 
.080 x 10 x 20 1 2 
2024-T3 Bare Sheet per AMS-QQ-A-
250/4 
Apply chemical conversion coating. Refer 
to SOPM 20-43-03. Apply two coats of 
BMS 10-20, Type II primer. Refer to 767 
AMM 28-11-00. Part mark. Refer to 
SOPM 20-50-10. 
Filler 
.100 x 2.2 x 3.6 1 2 
BACB30NW6K9Y Bolt – Oversize 3 6 
BACB30NW6K12Y Bolt – Oversize 1 2 
BACB30NW8K5X Bolt – Oversize 8 16 
BACB30NW8K6X Bolt – Oversize 10 20 
BACB30NW8K7X Bolt – Oversize 32 64 
BACB30NW8K8X Bolt – Oversize 24 48 
BACB30NW8K8Y Bolt – Oversize 2 4 
BACB30NW8K10X Bolt – Oversize 9 18 
BACB30NW8K12X Bolt – Oversize 1 2 
BACB30YP8K3 Bolt 3 6 
BACB30YP8K4 Bolt 8 16 
BACB30WQ5K5L ON2 Bolt – Radius Lead-in 2 4 
BACN10YT3CD Nut 4 8 
BACN10YT4CD Nut 91 182 
BACN10TN5K ON2 Nut 2 4 
BACC30BL8 Collar 11 22 
BACC30M8 Collar 15 30 
 
** Material dimension includes excess, trim as required 
ON1 BACR15BA()AD()C or BACR15GF()D() is acceptable to substitute BACR15BA()D()C. 
ON2 BACB30WQ5K6L + BACN10HY5M + BACW10AT35AS + BACW10AT35AS  
Optional to BACB30WQ5K5L + BACN10TN5K.

### Page 40

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 37 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 7e - Parts and Material List- Stringer L-9.5 Replacement & Stringer L-6.5 
Modification Kit AP767-57-010-05: 
AP767-57-010-05: Lower Skin Panel Internal Components Only Rework Kit for 
Group 3 Airplanes 
Material Description QTY per Wing QTY per SS 
BACB30NW8K5X Bolt – Oversize 3 6 
BACB30NW8K6X Bolt – Oversize 5 10 
BACB30NW8K9X Bolt – Oversize 3 6 
BACB30NW8K10X Bolt – Oversize 4 8 
BACC30M8 Collar 15 30 
BACB30WQ5K5L 
ON2 Bolt – Radius Lead-in 2 4 
BACN10TN5K 
ON2 Nut 2 4

### Page 41

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 38 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 7f - Parts and Material List- Stringer L-9.5 Replacement & Stringer L-6.5 
Modification Kit AP767-57-010-07: 
AP767-57-010-07: Lower Skin Panel Internal and External Components Rework Kit 
For Group 1 and Group 2 Airplanes 
Material Description QTY per Wing QTY Per SS 
767-3421-7 Stringer – L-9.5, Detail 1 1 
767-3421-8 Stringer – L-9.5, Detail 1 1 
2024-T3 Bare Sheet per AMS-QQ-A-
250/4 
(Shot peen all over, .004A - .007A, 
coverage 1 automated or 2 manual. 
Refer to SOPM 20-10-03) 
Check flatness by placing the part on a 
flat table. If a gap exists after 
application of limited localized force 
permitted by Appendix C, the part must 
be straightened by additional peening. 
Apply chemical conversion coating. 
Refer to SOPM 20-43-03. 
Apply two coats of BMS10-79, Type II 
primer. Refer to SOPM 20-44-04. 
Part mark. Refer to SOPM 20-50-10.  
Doubler** 
.080 x 10 x 25 1 2 
2024-T3 Bare Sheet per AMS-QQ-A-
250/4 
(Shot peen all over, .004A - .007A, 
coverage 1 automated or 2 manual. 
Refer to SOPM 20-10-03) 
Check flatness by placing the part on a 
flat table. If a gap exists after 
application of limited localized force 
permitted by Appendix C, the part must 
be straightened by additional peening. 
Apply chemical conversion coating. 
Refer to SOPM 20-43-03. 
Apply two coats of BMS10-79, Type II 
primer. Refer to SOPM 20-44-04. 
Part mark. Refer to SOPM 20-50-10. 
Tripler** 
.080 x 10 x 20 1 2 
2024-T3 Bare Sheet per AMS-QQ-A-
250/4 
Apply chemical conversion coating. 
Refer to SOPM 20-43-03. Apply two 
coats of BMS 10-20, Type II primer. 
Refer to 767 AMM 28-11-00. Part 
mark. Refer to SOPM 20-50-10. 
Filler 
.100 x 2.2 x 3.6 1 2 
BACF3F016J103AF Filler 1 2 
BACF3F016G125AF Filler 1 2 
BACS40R013C019F Shim 1 2 
BACS40R019C024F Shim 1 2 
BACS40R019C026F Shim 1 2 
BACS40R019C087F Shim 1 2

### Page 42

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 39 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 7f (Continued)  
Material Description QTY per Wing QTY Per SS 
BACS40R024C025F Shim 1 2 
BACS40R024C043F Shim 1 2 
BACB30NW6K9Y Bolt – Oversize 3 6 
BACB30NW6K12Y Bolt – Oversize 1 2 
BACB30NW8K4X Bolt – Oversize 2 4 
BACB30NW8K5X Bolt – Oversize 6 12 
BACB30NW8K6X Bolt – Oversize 8 16 
BACB30NW8K7X Bolt – Oversize 31 62 
BACB30NW8K8X Bolt – Oversize 25 50 
BACB30NW8K9X Bolt – Oversize 7 14 
BACB30NW8K10X Bolt – Oversize 9 18 
BACB30NW8K11X Bolt – Oversize 6 12 
BACB30NW8K11Y Bolt – Oversize 1 2 
BACB30NW8K12X Bolt – Oversize 1 2 
BACB30NW8K13X Bolt – Oversize 1 2 
BACB30NW10K10 Bolt 2 4 
BACB30NW10K13X Bolt – Oversize 5 10 
BACB30WQ5K5L ON2 Bolt – Radius Lead-in 2 4 
BACB30YP8K3 Bolt 3 6 
BACB30YP8K5 Bolt 8 16 
BACC30BL8 Collar 11 22 
BACC30M8 Collar 15 30 
BACC30M10 Collar 5 10 
BACN10TN5K ON2 Nut 2 4 
BACN10YT3CD Nut 4 8 
BACN10YT4CD Nut 72 144 
BACN10YT5CD Nut 2 4 
BACR15BA8D6C ON1 Rivet 5 10 
BACR15BA9D6C ON1 Rivet 5 10 
BACR15BA10D7C ON1 Rivet 5 10 
BACR15BA10D16C ON1 Rivet 7 14 
BACR15BA11D7C ON1 Rivet 5 10 
BACR15BA11D16C ON1 Rivet 7 14 
 
NOTE: This kit contains more parts than necessary depending on repair options selected by 
operator. Dispose of unused parts according to site procedures. 
** Material dimension includes excess, trim as required 
ON1 BACR15BA()AD()C or BACR15GF()D() is acceptable to substitute BACR15BA()D()C. 
ON2 BACB30WQ5K6L + BACN10HY5M + BACW10AT35AS + BACW10AT35AS  is acceptable to 
substitute BACB30WQ5K5L + BACN10TN5K.

### Page 43

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 40 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 7g - Parts and Material List- Stringer L-9.5 Replacement & Modification Kit 
AP767-57-010-09: 
AP767-57-010-09: Lower Skin Panel Internal and External Components Rework Kit 
For Group 1 and Group 2 Airplanes 
Material Description 
QTY QTY 
per Wing Per SS 
767-3421-7 Stringer – L-9.5, Detail 1 1 
767-3421-8 Stringer – L-9.5, Detail 1 1 
2024-T3 Bare Sheet per AMS-QQ-A-
250/4 Doubler** 
1 2 
(Shot peen all over, .004A - .007A, 
coverage 1 automated or 2 manual. 
Refer to SOPM 20-10-03) 
.080 x 10 x 25 
Check flatness by placing the part on a 
flat table. If a gap exists after 
application of limited localized force 
permitted by Appendix C, the part must 
be straightened by additional peening. 
  
Apply chemical conversion coating. 
Refer to SOPM 20-43-03.   
Apply two coats of BMS10-79, Type II 
primer. Refer to SOPM 20-44-04.   
Part mark. Refer to SOPM 20-50-10.    
2024-T3 Bare Sheet per AMS-QQ-A-
250/4 Tripler** 
1 2 
(Shot peen all over, .004A - .007A, 
coverage 1 automated or 2 manual. 
Refer to SOPM 20-10-03) 
.080 x 10 x 20 
Check flatness by placing the part on a 
flat table. If a gap exists after 
application of limited localized force 
permitted by Appendix C, the part must 
be straightened by additional peening. 
  
Apply chemical conversion coating. 
Refer to SOPM 20-43-03.   
Apply two coats of BMS10-79, Type II 
primer. Refer to SOPM 20-44-04.   
Part mark. Refer to SOPM 20-50-10.   
2024-T3 Bare Sheet per AMS-QQ-A-
250/4 Filler 
1 2 
Apply chemical conversion coating. 
Refer to SOPM 20-43-03. Apply two 
coats of BMS 10-20, Type II primer. 
Refer to 767 AMM 28-11-00. Part 
mark. Refer to SOPM 20-50-10. 
.100 x 2.2 x 3.6

### Page 44

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 41 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Material Description QTY per Wing QTY per SS 
BACF3F016J103AF Filler 1 2 
BACF3F016G125AF Filler 1 2 
BACS40R013C019F Shim 1 2 
BACS40R019C024F Shim 1 2 
BACS40R019C026F Shim 1 2 
BACS40R019C087F Shim 1 2 
BACS40R024C025F Shim 1 2 
BACS40R024C043F Shim 1 2 
BACB30NW6K9Y Bolt – Oversize 3 6 
BACB30NW6K12Y Bolt – Oversize 1 2 
BACB30NW8K4X Bolt – Oversize 2 4 
BACB30NW8K5X Bolt – Oversize 3 6 
BACB30NW8K6X Bolt – Oversize 3 6 
BACB30NW8K7X Bolt – Oversize 31 62 
BACB30NW8K8X Bolt – Oversize 25 50 
BACB30NW8K9X Bolt – Oversize 4 8 
BACB30NW8K10X Bolt – Oversize 5 10 
BACB30NW8K11X Bolt – Oversize 6 12 
BACB30NW8K11Y Bolt – Oversize 1 2 
BACB30NW8K12X Bolt – Oversize 1 2 
BACB30NW8K13X Bolt – Oversize 1 2 
BACB30NW10K10 Bolt 2 4 
BACB30NW10K13X Bolt – Oversize 5 10 
BACB30YP8K3 Bolt 3 6 
BACB30YP8K5 Bolt 8 16 
BACC30BL8 Collar 11 22 
BACC30M10 Collar 5 10 
BACN10YT3CD Nut 4 8 
BACN10YT4CD Nut 72 144 
BACN10YT5CD Nut 2 4 
BACR15BA8D6C ON1 Rivet 5 10 
BACR15BA9D6C ON1 Rivet 5 10 
BACR15BA10D7C ON1 Rivet 5 10 
BACR15BA10D16C ON1 Rivet 7 14 
BACR15BA11D7C ON1 Rivet 5 10 
BACR15BA11D16C ON1 Rivet 7 14 
NOTE: This kit contains more parts than necessary depending on repair options selected by 
operator. Dispose of unused parts according to site procedures. 
** Material dimension includes excess, trim as required 
ON1 BACR15BA()AD()C or BACR15GF()D() is acceptable to substitute BACR15BA()D()C.

### Page 45

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 42 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 7h - Additional parts required to rework -01 kit into -09 kit.  
(Customer furnished) 
Material Description QTY per Wing QTY per SS 
2024-T3 Bare Sheet per AMS-QQ-A-250/4 
(Shot peen all over, .004A - .007A, 
coverage 1 automated or 2 manual. Refer 
to SOPM 20-10-03) 
Check flatness by placing the part on a flat 
table. If a gap exists after application of 
limited localized force permitted by 
Appendix C, the part must be straightened 
by additional peening. 
Apply chemical conversion coating. Refer to 
SOPM 20-43-03. 
Apply two coats of BMS10-79, Type II 
primer. Refer to SOPM 20-44-04. 
Part mark. Refer to SOPM 20-50-10.  
Doubler** 
.080 x 10 x 25 1 2 
2024-T3 Bare Sheet per AMS-QQ-A-250/4 
(Shot peen all over, .004A - .007A, 
coverage 1 automated or 2 manual. Refer 
to SOPM 20-10-03) 
Check flatness by placing the part on a flat 
table. If a gap exists after application of 
limited localized force permitted by 
Appendix C, the part must be straightened 
by additional peening. 
Apply chemical conversion coating. Refer to 
SOPM 20-43-03. 
Apply two coats of BMS10-79, Type II 
primer. Refer to SOPM 20-44-04. 
Part mark. Refer to SOPM 20-50-10. 
Tripler** 
.080 x 10 x 20 1 2 
2024-T3 Bare Sheet per AMS-QQ-A-250/4 
Apply chemical conversion coating. Refer to 
SOPM 20-43-03. Apply two coats of BMS 
10-20, Type II primer. Refer to 767 AMM 
28-11-00. Part mark. Refer to SOPM 20-50-
10. 
Filler 
.100 x 2.2 x 3.6 1 2 
BACR15BA11D16C ON1 Rivet 7 14 
BACR15BA10D16C ON1 Rivet 7 14 
BACB30NW6K9Y Bolt – Oversize 3 6 
BACB30NW6K12Y Bolt – Oversize 1 2 
BACB30NW8K7X Bolt – Oversize 28 56 
BACB30NW8K8X Bolt – Oversize 25 50 
BACB30NW8K11Y Bolt – Oversize 1 2 
BACB30NW8K12X Bolt – Oversize 1 2 
BACB30NW8K13X Bolt – Oversize 1 2

### Page 46

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 43 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 7h (Continued) 
Material Description QTY per Wing QTY per SS 
BACB30NW10K10 Bolt 2 4 
BACB30YP8K3 Bolt 3 6 
BACB30YP8K5 Bolt 8 16 
BACC30BL8 Collar 11 22 
BACN10YT3CD Nut 4 8 
BACN10YT4CD Nut 53 106 
BACN10YT5CD Nut 2 4 
BACR15BA11D16C ON1 Rivet 7 14 
BACR15BA10D16C ON1 Rivet 7 14 
ON1 BACR15BA()AD()C or BACR15GF()D() is acceptable to substitute BACR15BA()D()C. 
 
Table 7i - Additional parts required to rework -02 kit into -09 kit.  
(Customer furnished) 
Material Description QTY per Wing QTY per SS 
BACB30NW8K13X Bolt – Oversize 1 2 
BACR15BA9D6C ON1 Rivet 5 10 
BACR15BA11D16C ON1 Rivet 7 14 
BACR15BA10D16C ON1 Rivet 7 14 
BACB30NW8K8X Bolt – Oversize 1 2 
BACB30NW8K11Y Bolt – Oversize 1 2 
BACB30YP8K5 Bolt 8 16 
BACB30NW10K10 Bolt 2 4 
BACN10YT5CD Nut 2 4 
ON1 BACR15BA()AD()C or BACR15GF()D() is acceptable to substitute BACR15BA()D()C.

### Page 47

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 44 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 7j - Additional parts required to rework -03 kit into -09 kit.  
(Customer furnished) 
Material Description QTY per Wing QTY per SS 
2024-T3 Bare Sheet per AMS-QQ-A-250/4 
(Shot peen all over, .004A - .007A, 
coverage 1 automated or 2 manual. Refer 
to SOPM 20-10-03) 
Check flatness by placing the part on a flat 
table. If a gap exists after application of 
limited localized force permitted by 
Appendix C, the part must be straightened 
by additional peening. 
Apply chemical conversion coating. Refer to 
SOPM 20-43-03. 
Apply two coats of BMS10-79, Type II 
primer. Refer to SOPM 20-44-04. 
Part mark. Refer to SOPM 20-50-10.  
Doubler** 
.080 x 10 x 25 1 2 
2024-T3 Bare Sheet per AMS-QQ-A-250/4 
(Shot peen all over, .004A - .007A, 
coverage 1 automated or 2 manual. Refer 
to SOPM 20-10-03) 
Check flatness by placing the part on a flat 
table. If a gap exists after application of 
limited localized force permitted by 
Appendix C, the part must be straightened 
by additional peening. 
Apply chemical conversion coating. Refer to 
SOPM 20-43-03. 
Apply two coats of BMS10-79, Type II 
primer. Refer to SOPM 20-44-04. 
Part mark. Refer to SOPM 20-50-10. 
Tripler** 
.080 x 10 x 20 1 2 
2024-T3 Bare Sheet per AMS-QQ-A-250/4 
Apply chemical conversion coating. Refer to 
SOPM 20-43-03. Apply two coats of BMS 
10-20, Type II primer. Refer to 767 AMM 
28-11-00. Part mark. Refer to SOPM 20-50-
10. 
Filler 
.100 x 2.2 x 3.6 1 2 
BACR15BA11D16C ON1 Rivet 7 14 
BACR15BA10D16C ON1 Rivet 7 14 
BACB30NW6K9Y Bolt – Oversize 3 6 
BACB30NW6K12Y Bolt – Oversize 1 2 
BACB30NW8K7X Bolt – Oversize 28 56 
BACB30NW8K8X Bolt – Oversize 25 50 
BACB30NW8K11Y Bolt – Oversize 1 2 
BACB30NW8K12X Bolt – Oversize 1 2 
BACB30NW10K10 Bolt 2 4

### Page 48

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 45 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Table 7j (Continued) 
Material Description QTY per Wing QTY per SS 
BACB30YP8K3 Bolt 3 6 
BACB30YP8K5 Bolt 8 16 
BACC30BL8 Collar 11 22 
BACN10YT3CD Nut 4 8 
BACN10YT4CD Nut 52 104 
BACN10YT5CD Nut 2 4 
 
ON1 BACR15BA()AD()C or BACR15GF()D() is acceptable to substitute BACR15BA()D()C. 
Table 7k - Additional parts required to rework -04 kit into -09 kit.  
(Customer furnished) 
Material Description QTY per Wing QTY per SS 
BACR15BA11D16C ON1 Rivet 7 14 
BACR15BA10D16C ON1 Rivet 7 14 
BACB30NW8K8X Bolt – Oversize 1 2 
BACB30NW8K11Y Bolt – Oversize 1 2 
BACB30YP8K5 Bolt 8 16 
BACB30NW10K10 Bolt 2 4 
BACN10YT5CD Nut 2 4 
ON1 BACR15BA()AD()C or BACR15GF()D() is acceptable to substitute BACR15BA()D()C.

### Page 49

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 46 of 111 
 
Aviation Partners Boeing PROPRIETARY 
2. Parts and Materials Supplied by the Operator: 
Group 1, 2 and 3 Airplanes 
Materials for Lower Skin Panel Internal Components Only Rework 
Material Description QTY per Wing QTY per SS 
BMS10-20, Type II Primer * * 
BMS10-79 Type II Primer * * 
BMS5-45 Class A, B, and C Sealant * * 
Alodine 600 Alodine * * 
BMS 10-60, Type II, Color 
BAC 707 Gray or the 
operator’s normal decorative 
exterior paint system 
Topcoat * * 
* Quantity as required. 
 
Group 1 and 2 Airplanes 
Materials for Lower Skin Panel Internal and External Components Rework 
Material Description QTY per Wing QTY per SS 
BMS10-20 Type II Primer * * 
BMS10-79 Type II Primer * * 
BMS5-45 Class A, B, and C Sealant * * 
Alodine 600 Alodine * * 
BMS 5-95 Class B Sealant * * 
BMS 10-60, Type II, Color 
BAC 707 Gray or the 
operator’s normal decorative 
exterior paint system 
Topcoat * * 
* Quantity as required. 
 
C. PARTS NECESSARY TO CHANGE SPARES 
None.

### Page 50

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 47 of 111 
 
Aviation Partners Boeing PROPRIETARY 
D. EXISTING PARTS ACCOUNTABILITY 
Table 8 - Existing Parts Accountability for Stringer L-9.5 Replacement 
The parts shown below are changed as shown in this service bulletin. Quantity is 
the number of parts changed on each airplane. 
Group 1: 
Existing Part 
Number 
RUC Name QTY New Part Number PNC RPC 
767-3421-1 DIS Stringer 1 767-3421-7 S A 
767-3421-2 DIS Stringer 1 767-3421-8 S A 
Group 2: 
Existing Part 
Number 
RUC Name QTY New Part Number PNC RPC 
767-3421-3 DIS Stringer 1 767-3421-7 S A 
767-3421-4 DIS Stringer 1 767-3421-8 S A 
 
RUC Recommended Use Code 
DIS - Discard the part 
PNC Part Number Code 
S - This is the part number for the new equivalent or replacement part 
 - To get a new part, use this part number in your order. 
 
RPC Replacement Code 
A - Do not use the existing part to replace the new or changed part. 
E. SPECIAL TOOLING - PRICE AND AVAILABILITY 
No special tooling is required to perform repairs. 
F. SPECIAL TOOLING NECESSARY TO DO THIS SERVICE BULLETIN 
Maintenance and overhaul tools as specified in the maintenance manuals may 
be necessary. Examine operator tool supply before starting work to make sure all 
necessary tools are available.

### Page 51

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 48 of 111 
 
Aviation Partners Boeing PROPRIETARY 
3. ACCOMPLISHMENT INSTRUCTIONS 
A. GENERAL NOTES 
WARNING:  IF ELECTRICAL POWER IS APPLIED TO THE AIRPLANE, MAKE 
SURE YOU OBEY ALL PRECAUTIONS WHILE YOU DO WORK. IF YOU DO 
NOT OBEY THE PRECAUTIONS, DEATH OR INJURY TO PERSONS, AND 
DAMAGE TO THE AIRPLANE CAN OCCUR. 
WARNING:  CAREFULLY DO ALL OF THE SAFETY PROCEDURES IN THE 
PURGING AND ENTRY PROCEDURE OF THE FUEL TANK. INJURY TO 
PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR. 
CAUTION:  KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES 
CLEAN OF METAL PARTICLES OR CONTAMINATION WHEN YOU USE 
TOOLS. UNWANTED MATERIAL, METAL PARTICLES, OR CONTAMINATION 
CAUGHT IN WIRE BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. 
DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR OTHER ELECTRICAL 
DAMAGE. 
CAUTION:  ELECTRICALLY GROUND THE AIRPLANE. THIS WILL HELP TO 
PREVENT DAMAGE TO THE AIRPLANE OR EQUIPMENT. 
NOTE: 1. Obey all warnings and cautions given in the applicable sections of 
the Aircraft Maintenance Manual (AMM). 
2. Perform functional tests and adjustments prior to returning the 
aircraft to service. 
3. Unless shown differently, these dimensions and tolerances are 
used: 
- Linear dimensions are in inches. 
- Tolerance on linear dimensions, other than rivet and bolt edge 
margins, is plus or minus 0.03 inch. 
- Tolerance on rivet and bolt edge margin is plus or minus 0.05 
inch. 
- Angular tolerance is plus or minus 2 degrees. 
- Hole dimensions for standard solid rivets are given in the 767 
Structural Repair Manual (SRM), 51-40-05. 
- Torque limits to tighten nut and bolts are given in the 767 SRM, 
51-40-04. 
4. Make an entry into aircraft maintenance records once service 
bulletin is completed. 
5. For approved material, fastener, and process substitutions, refer to 
the 767 SRM, Chapter 51 or Boeing drawing 012W6100, Alternate 
fasteners are given in the 767 SRM 51-40-03 and Boeing drawing 
012W6100.

### Page 52

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 49 of 111 
 
Aviation Partners Boeing PROPRIETARY 
6. If the length of any fastener specified in this service bulletin does 
not meet the installation standards in 767 SRM, Chapter 51, then a 
fastener of the same specification or an approved substitute, with a 
length which meets the installation standards in the 767 SRM, 
Chapter 51 may be used. 
7. These work instructions refer to procedures included in other 
Boeing documents. When the words “refer to” are used and the 
operator has an accepted alternative procedure, the accepted 
alternative procedure can be used. When the words “in accordance 
with” are included in the instruction, the procedure in the document 
must be used. 
8. If it is necessary to remove more parts for access, you can remove 
those parts. If you can get access without removing identified parts, 
it is not necessary to remove all of the identified parts. Jacking and 
shoring limitations must be observed. 
9. When more than one OPTION is given for a CONDITION, do only 
one of the OPTION numbers. When more than one ACTION is 
given for a CONDITION number or an OPTION number, do all of 
the ACTION numbers for that CONDITION number or OPTION 
number. 
10. Some steps in the Work Instructions are labeled as Required for 
Compliance (RC). If this service bulletin is mandated by an 
airworthiness directive (AD), then the steps labeled RC, including 
sub-steps under an RC step and any figures identified in an RC 
step, must be done to comply with the AD. An Alternative Method of 
Compliance (AMOC) is required for any deviations to RC steps, 
including sub-steps and identified figures.  Steps not labeled as RC 
may be deviated from using accepted methods in accordance with 
the operator’s maintenance or inspection program without obtaining 
approval of an AMOC.  This is provided that the RC steps, including 
sub-steps and identified figures, can still be done as specified, and 
the airplane can be put back in an airworthy condition. 
11. The External Doubler/Tripler, Filler repair at Stringer L-9.5 in 
accordance with PART 8 and the External Doubler/Tripler, Filler 
and new Stringer at Stringer L-9.5 in accordance with PART 11 are 
classified as Category B repairs for which supplemental inspections 
in accordance with PART 9 and PART 13, respectively, are 
necessary. All other repairs are classified as Category A repairs. 
Refer to the 767 SRM, 51-00-06 for the definitions of the different 
categories of repairs. 
12. Refer to 767 SRM, 51-20-13 for the definition of surface roughness. 
13. The compliance times for the actions in Paragraph 3.B., WORK 
INSTRUCTIONS are in Paragraph 1.E., Compliance.

### Page 53

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 50 of 111 
 
Aviation Partners Boeing PROPRIETARY 
B. WORK INSTRUCTIONS 
PART 1: HFEC INSPECTION OF LOWER OUTBOARD WING SKIN EXTERNAL 
SURFACE - STRINGER L-9.5 
NOTE: Aviation Partners Boeing requests the operators to report the results of inspection to 
Aviation Partners Boeing. See Appendix A for the format of the report. 
1. RC for Group 1 and 2 Airplanes - Do a high frequency eddy current (HFEC) 
surface inspection of the lower wing skin to detect crack(s) at the fasteners 
common to the outboard stringer L-9.5 between Rib 31 Wing Station (WSTA) 
990.20 and Rib 32 WSTA 1018.20. Refer to 767 NDT Manual (D634T301, 
Part 6, Subject 51-00-01 or 51-00-19) for accepted procedures. See Figure 2 
for location.  
a. Condition 1 - If no crack is found,  
Do one of the options 1, 2, 3 and 4.  
(1) Condition 1, Option 1 –  
Repeat Part 1: HFEC Inspection of Lower Outboard Wing Skin 
External Surface – Stringer L-9.5 
- OR - 
(2) Condition 1, Option 2 –  
Do Part 2: Hole Preparation  
Do Part 3: Plug Zero-Timed Holes in Wing Skin, 
Do Part 4: Plug Open Holes in Lower Wing Skin, 
Do Part 5: Repair Action – Preventive Modification – Stringer L-9.5, 
Do Part 6: Close Access after Preventive Modification and Replacement 
NOTE: If the result of Part 2, Step 8 is Condition 3, obey the instructions 
for condition 3 and do not do Parts 3 thru 6. 
- OR - 
(3) Condition 1, Option 3 –  
Do Part 8: Repair Action - Preventive Modification - External 
Doubler/Tripler, Filler at Stringer L-9.5 
Do Part 6: Close Access after Preventive Modification and 
Replacement 
Do Part 9: HFEC Inspection of Lower Outboard Wing Skin Common to 
the External Doubler/Tripler Repair at Stringer L-9.5 
- OR -

### Page 54

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 51 of 111 
 
Aviation Partners Boeing PROPRIETARY 
(4) Condition 1, Option 4 –  
(An alternative to Option 3 if Stringer replacement is necessary) 
Do Part 11: Repair Action - Preventive Modification - External 
Doubler/Tripler, Filler and New Stringer at Stringer L-9.5 
Do Part 6: Close Access after Preventive Modification and 
Replacement 
Do Part 13: HFEC Inspection of Lower Outboard Wing Skin Common 
to the External Doubler/Tripler Repair at Stringer L-9.5 
b. Condition 2 - If any crack is found,  
Do one of the following. 
(1) Condition 2, Option 1 –  
Do Part 8: Repair Action - Preventive Modification - External 
Doubler/Tripler, Filler at Stringer L-9.5 
Do Part 6: Close Access after Preventive Modification and 
Replacement 
Do Part 9: HFEC Inspection of Lower Outboard Wing Skin Common 
to the External Doubler/Tripler Repair at Stringer L-9.5 
- OR - 
(1) Condition 2, Option 2 –  
(An alternative to Option 1 if Stringer replacement is necessary) 
Do Part 11: Repair Action - Preventive Modification - External 
Doubler/Tripler, Filler and New Stringer at Stringer L-9.5 
Do Part 6: Close Access after Preventive Modification and 
Replacement 
Do Part 13: HFEC Inspection of Lower Outboard Wing Skin Common 
to the External Doubler/Tripler Repair at Stringer L-9.5

### Page 55

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 52 of 111 
 
Aviation Partners Boeing PROPRIETARY 
PART 2: HOLE PREPARATION 
Steps 7, 8, 9, 10, and 11 are RC for Group 1 and 2 Airplanes, Condition 
1-Option 2  
1. Defuel the left and right main fuel tanks. Refer to the 767 AMM, 28-26-00 as 
an accepted procedure. 
2. Purge main tanks and prepare surge tank for entry. Refer to the 767 AMM, 
28-11-00 as an accepted procedure. 
3. Remove electrical power from the airplane. Refer to the 767 AMM, 24-22-00 
as an accepted procedure. 
4. Remove and keep the following access panels. Refer to the 767 AMM, 28-11-
03 as an accepted procedure. 
• Left Wing 542AB, 542BB, and 542CB 
• Right Wing 642AB, 642BB, and 642CB 
5. Remove the left and right fuel vent tube assemblies for additional access. 
Refer to the 767 AMM, 28-13-00 as an accepted procedure. 
6. Remove the slat track drain tube from the lower wing skin for additional 
access. Refer to the 767 AMM, 28-11-11 as an accepted procedure. 
7. For the five holes at the inboard end of stringer L-9.5, remove the fasteners 
and prepare to zero-time the five (5) open fastener holes on the lower skin 
and stringer of the wing. Refer to the Group A holes in Figure 5 (Sheet 2 of 2). 
Refer to the 767 SRM, 51-40-02 as an accepted procedure for fastener 
removal. Do all the zero-timing operation except the final 1/16 oversize, and 
do not exceed a hole size of 0.288 inch diameter while attempting to remove 
a crack. Refer to the 767 SRM, 51-10-02 as an accepted procedure. 
NOTE: The zero-timing operation in the 767 SRM, 51-10-02 specifies doing 
an HFEC inspection and 1/16 oversize. 
8. Evaluate the rework of the holes to determine the required course of action:  
a. If all five holes are less than or equal to 0.288 inch in diameter with no 
crack indication found by HFEC inspection: Proceed to step 9 of PART 
2. 
b. Condition 3 - If any of the five holes have crack indications found by 
HFEC inspection after oversizing to 0.288 inch diameter or larger, do 
one of the following options: 
(1) Condition 3, Option 1 –  
Do Part 8: Repair Action - Preventive Modification - External 
Doubler/Tripler, Filler at Stringer L-9.5 
Do Part 6: Close Access after Preventive Modification and 
Replacement

### Page 56

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 53 of 111 
 
Aviation Partners Boeing PROPRIETARY 
Do Part 9: HFEC Inspection of Lower Outboard Wing Skin Common 
to the External Doubler/Tripler Repair at Stringer L-9.5 
This completes Part 2, no additional steps for Part 2 required. 
 
- OR - 
(2) Condition 3, Option 2 –  
(An alternative to Option 1 if Stringer replacement is necessary) 
Do Part 11: Repair Action - Preventive Modification - External 
Doubler/Tripler, Filler and New Stringer at Stringer L-9.5 
Do Part 6: Close Access after Preventive Modification and 
Replacement 
Do Part 13: HFEC Inspection of Lower Outboard Wing Skin Common 
to the External Doubler/Tripler Repair at Stringer L-9.5 
This completes Part 2, no additional steps for Part 2 required. 
 
9. Remove all remaining fasteners common to outboard stringer L-9.5 (P/N 767-
3421-1/-2 for Group 1 airplanes, or 767-3421-3/-4 for Group 2 airplanes). See 
Figure 5 (Sheet 2 of 2). Refer to the 767 SRM, 51-40-02 as an accepted 
procedure for fastener removal. 
10. Remove stringer L-9.5, fillers, shims, and excess sealant as shown in Figure 
5 (Sheet 1 of 2). Clean area of removed parts. Refer to Standard Overhaul 
Practices Manual (SOPM) 20-30-03 as an accepted procedure. 
CAUTION:  The removal of stringer L-9.5 will require cutting the stringer in 
several pieces. Take all necessary precautions to prevent damage to 
surrounding structure. 
11. Perform 1/16 oversize for the Group A holes in Figure 5 (Sheet 2 of 2). 
12.  Proceed to do PART 3: Plug Zero-Timed Holes in Wing Skin.

### Page 57

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 54 of 111 
 
Aviation Partners Boeing PROPRIETARY 
 
 
 
 
 
 
 
 
 
 
Figure 5: Part 2: Hole Preparation  
(Sheet 1 of 2) 
(NOTE: For clarity, upper skin, vent tube, and slat can are not shown.) 
RIB 32 WSTA 1018.2 
STR L10 
STR L9 
REMOVE FASTENERS COMMON TO STRINGER L-9.5 
STRINGER L-9.5 DETAIL (P/N 767-3421-1/-2 or 
767-3421-3/-4) 
REMOVE FILLERS, SHIMS, AND EXCESS SEALANT 
UP FWD 
OUTBD 
RIB 31 WSTA 990.2

### Page 58

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 55 of 111 
 
Aviation Partners Boeing PROPRIETARY 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 5: PART 2: Hole Preparation 
(Sheet 2 of 2) 
STR L9.5 
REMOVED STRINGER DETAIL 
112T4000 REF 
LOWER WING SKIN 
767-3400 REF 
OUTBD LOWER WING SKIN 
GROUP C HOLES 
PART 4 - PLUG OPEN HOLES IN LOWER 
WING SKIN- 
PLUG HOLES WITH RIVETS. 
SEE PART 4 WORK INSTRUCTIONS 
7 PLACES 
WSTA 
1018.2 
REF 
GROUP B HOLES 
PART 4 - PLUG OPEN HOLES IN LOWER WING SKIN- 
PLUG HOLES WITH RIVETS.  
SEE PART 4 WORK INSTRUCTIONS 
5 PLACES 
FWD 
OUTBD 
GROUP A HOLES 
PART 2 – HOLE PREPARATION 
 INSPECT (QTY 5) OPEN HOLES IN LOWER 
WING SKIN 
PART 3 – PLUG ZERO-TIMED HOLES IN 
WING SKIN

### Page 59

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 56 of 111 
 
Aviation Partners Boeing PROPRIETARY 
PART 3: PLUG ZERO-TIMED HOLES IN WING SKIN 
1. RC for Group 1 and 2 Airplanes, Condition 1-Option 2 - Do either Step a 
or Step b below for each Group A hole in Figure 5 (Sheet 2 of 2).  
a. If the hole is less than or equal to 0.318 inch in diameter, do Steps a.(1) 
through a.(7). 
(1) Ream the hole to 0.315 – 0.318 inch diameter. 
(2) Countersink the external side of the skin 100 degrees to a depth of 
0.035–0.045 inch. 
(3) Plug the hole with a rivet (P/N BACR15BA10D7C). 
It is acceptable to substitute BACR15BA10AD7C or BACR15GF10D7 
rivet for BACR15BA10D7C. 
(4) Overdrive each rivet so that the driven button head (tail) diameter is 
1.4d minimum. Refer to 767 SRM 51-40-02 as an accepted 
procedure. 
(5) Shave the head of each rivet to be flush +0.010/-0.000 inch to the 
exterior skin. It is permitted to shave the head of BACR15GF rivet. 
(6) Touch up finish. Manually apply Alodine 600 to bare external surfaces 
including shaved rivet head. Refer to SOPM 20-43-03 as an accepted 
procedure. Manually apply one coat of BMS10-79, Type II primer to 
bare external surfaces including shaved rivet head. Refer to SOPM 
20-44-04 as an accepted procedure. 
(7) Apply brushcoat sealant BMS5-45 class A to rivet driven button and 
cap seal rivet driven button with BMS5-45 class B. Refer to AMM 28-
11-00 as an accepted procedure. 
b. If the hole diameter is greater than .318 inch and less than or equal to 
.351 inch, do Steps b.(1) through b.(7).   
(1) Ream the hole to 0.348 – 0.351 inch diameter. 
(2) Countersink the external side of the skin 100 degrees to a depth of 
0.035–0.045 inch. 
(3) Plug the hole with a rivet, P/N BACR15BA11D7C. 
It is acceptable to substitute BACR15BA11AD7C or BACR15GF11D7 
rivet for BACR15BA11D7C. 
(4) Overdrive each rivet so that the driven button head (tail) diameter is 
1.4d minimum. Refer to 767 SRM 51-40-02 as an accepted 
procedure. 
(5) Shave the head of each rivet to be flush +0.010/-0.000 inch to the 
exterior skin. It is permitted to shave the head of BACR15GF rivet.

### Page 60

AVIATION PARTNERS BOEING SERVICE BULLETIN AP767-57-010 
 
Original Issue: October 23, 2013  AP767-57-010 
Revision 14: November 17, 2025 Page 57 of 111 
 
Aviation Partners Boeing PROPRIETARY 
(6) Touch up finish. Manually apply Alodine 600 to bare surfaces 
including shaved rivet head. Refer to SOPM 20-43-03 as an accepted 
procedure. Manually apply one coat of BMS10-79, Type II primer to 
bare surfaces including shaved rivet head. Refer to SOPM 20-44-04 
as an accepted procedure. 
(7) Apply brushcoat sealant BMS5-45 class A to rivet driven button and 
cap seal rivet driven button with BMS5-45 class B. Refer to AMM 28-
11-00 as an accepted procedure. 
2. Proceed to do PART 4: Plug Open Holes in Lower Wing Skin.

The text continues at https://openairdocs.org/service-documents/aviation-partners-boeing/ap767-57-010/file/6fef3e95e397.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
