# BAE Systems Service Bulletin 32-A-JA140940: No revision named

- Rights: © BAE Systems. Filed by the FAA in regulations.gov docket FAA-2014-1093; AD 2015-06-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [BAE Systems Service Bulletin 32-A-JA140940](https://openairdocs.org/service-documents/bae-systems/32-a-ja140940.md)
- Title as filed: SB 32-JA140940
- Pages: 20
- PDF: https://openairdocs.org/files/sha256/01/33/0133b1fe4d8b63b808eece6552cdb89a8a752a662a3717d11364f0d8947269ec
- Page: https://openairdocs.org/service-documents/bae-systems/32-a-ja140940/file/0133b1fe4d8b

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ORIGINAL ISSUE: 3 rd  October 2014  32-A-JA140940 
  PAGE 1 OF 1 
 
 
SERVICE BULLETIN
 
BAE SYSTEMS (OPERATIONS) LIMITED, 
PRESTWICK INTERNATIONAL AIRPORT, 
AYRSHIRE, KA9 2RW, 
SCOTLAND. 
32-A-JA140940 
 
 
TRANSMITTAL SHEET 
 
This page transmits the original issue of Service Bulletin 32-A-JA140940. 
 
 
TITLE: LANDING GEAR – INSPECTION OF MAIN LANDING GE AR SPECIAL WASHER 
INSTALLATION. 
INSPECTION

### Page 2

(No text on this page.)

### Page 3

ORIGINAL ISSUE: 3 rd  October 2014  32-A-JA140940 
  PAGE 1 OF 14 
 
 
SERVICE BULLETIN
 
BAE SYSTEMS (OPERATIONS) LIMITED, 
PRESTWICK INTERNATIONAL AIRPORT, 
AYRSHIRE, KA9 2RW, 
SCOTLAND. 
32-A-JA140940 
TITLE: LANDING GEAR – INSPECTION OF MAIN LANDING GE AR SPECIAL WASHER 
INSTALLATION. 
INSPECTION 
1. PLANNING INFORMATION 
A. Effectivity 
All Jetstream Series 3100 and 3200 aircraft. 
B. Reason 
Cases have been reported of migration (rotation relative to the Main Landing Gear 
(MLG) cylinder) of the special washer that was introduced by Service Bulletin (SB) 32-
JM7862. The migration is believed to be caused when the bearing cap has been 
installed with the bearing locking pins facing the special washer, as per SB 32-JM7862 
Revision 1. If adverse tolerances also exist, then the bearing locking pins can foul the 
special washer. 
Such fouling could prevent the special washer from rotating with the landing gear during 
retraction and extension and may cause degradation of the corrosion protection on the 
forward face of the MLG spigot (pintle) housing by the action of rubbing under pressure. 
Loss of corrosion protection in this area could result in the onset of corrosion pitting. 
Corrosion pitting is undesirable on cylinders made from L161. On cylinders made from 
DTD5094, stress corrosion cracking can initiate from corrosion pits. Stress corrosion 
cracking has been known to result in failure of the MLG spigot housing, resulting in the 
collapse of the MLG. 
C. Description 
This SB describes the inspection of the special washer installed at the MLG forward 
spigot and the resulting actions. This SB is in three parts:- 
Part 1 describes the visual inspection of the special washer installation to determine if 
the special washer has migrated. 
Part 2 describes the removal of the special washer, checking the MLG spigot housing  
for damage and installing a new or serviceable special washer (i.a.w. SB32-JM7862 
Revision 3). 
Part 3 describes the follow up inspection, using the witness paint described in Part 1 or  
Part 2, to check if the special washer has migrated.

### Page 4

SERVICE BULLETIN  
32-A-JA140940  ORIGINAL ISSUE: 3 rd  October 2014 
PAGE 2   
 
 
Part 1 tasks are as follows:- 
- Perform a visual inspection of the special washer  for evidence of migration. 
- If there is no evidence of special washer migrati on, apply a small amount of suitable 
witness paint over the top inboard side edge of the special washer tab and onto the 
flat of the MLG spigot housing. 
Part 2 tasks are as follows:- 
- Remove the affected MLG leg from the aircraft. 
- Remove the forward (flanged) spigot (pintle) pin from the leg. 
- Remove the special washer from the leg. 
- Remove any remains of gasket material on the wash er and leg. 
- Clean and visually inspect the forward face of th e MLG spigot housing. 
- Check for evidence of wear marks that may have be en caused by migration of the 
special washer. 
- Check for any signs of corrosion. 
- Remove all corrosion and wear marks. 
- Perform an NDT inspection of the MLG spigot housi ng for cracks (only required for 
cylinders made from DTD5094). 
- Restore the protective treatment on the forward f ace of the MLG spigot housing. 
- Inspect the special washer for wear and damage. 
- Discard special washer if worn or damaged. 
- If necessary, install a new special washer. 
- Apply a small amount of witness paint over the to p inboard side edge of the special 
washer tab and onto the flat of the MLG spigot housing. 
- Install the forward (flanged) spigot (pintle) pin  on the MLG leg. 
- Install the MLG leg on the aircraft. 
- Perform retraction/extension check of the MLG. 
- Check that the witness paint is still intact. 
- If the witness paint is broken, report findings t o BAE Systems and await instructions 
before further flight. 
- Report all findings to BAE Systems, including if no faults found. 
 
Part 3 tasks are as follows:- 
- Check that the witness paint between the special washer tab and the flat of the MLG 
spigot housing is still intact. 
- If the paint is broken, report findings to BAE Sy stems and await instructions before 
further flight. 
- Report all findings to BAE Systems, including if no faults are found.

### Page 5

SERVICE BULLETIN  
ORIGINAL ISSUE: 3 rd  October 2014  32-A-JA140940 
  PAGE 3 
 
 
D. Manpower 
Part 1 = 1 hour, 
Part 2 = 8 hours per affected leg, 
Part 3 = 1 hour. 
Mechanical skills are necessary. 
E. Material - Cost and Availability 
Cost and availability is by arrangement between the Operator and BAE SYSTEMS. 
F. Tooling - Price and Availability 
Not applicable. 
G. Weight and Balance 
Not affected. 
H. Aircraft Noise Levels 
Not affected. 
I. Electrical Load Data 
Not affected. 
J. Software Accomplishment Summary 
Not applicable. 
K. References 
-  Aircraft Maintenance Manual Chapters 24 and 32. 
- SB 32-A-JA851226. 
- SB 32-JM7862 at Revision 3 or later. 
- SRM 51-10-31. 
- MLG CMM’s 31-10-01, -02, -03. 
L. Publications Affected 
Not applicable. 
M. Family Tree Of Modification Relationships 
Not applicable.

### Page 6

SERVICE BULLETIN  
32-A-JA140940  ORIGINAL ISSUE: 3 rd  October 2014 
PAGE 4   
 
 
N. Approval 
The technical content of this SB is the subject of EASA Airworthiness Directive 
consultation. 
Compliance with this SB must be achieved as follows:- 
NOTE: For compliance purposes, the following landin g gear part numbers have 
cylinders made from DTD5094:- 
Left Hand Types: 1863 (without strike off 3), 1863/ 4A, 1863/4B and 1863/4C 
(Pre Mod 86--04--003 Re--issue 6), B00A702850A 
(without strike off 7 or 16), B00A702925A (without strike 
off 5 or 15). 
Right Hand Types: 1864 (without strike off 3), 1864/4A, 1864/4B and 1864/4C, 
(Pre Mod 86--04--003 Re--issue 6), B00A702851A 
(without strike off 7 or 16), B00A702926A (without strike 
off 5 or 15). 
All other gear part numbers (including all Jetstream Series 3200 gear types) 
have cylinders made from L161. 
On landing gears (left hand or right hand) where SB 32-JM7862 was first accomplished 
at revision 2, perform an inspection for evidence of special washer migration (Part 1 of 
this SB). For landing gears with DTD5094 cylinders (see note above) this is to be 
performed within 50 cycles or 2 calendar weeks of the issue date of this SB, whichever 
is the earlier. For gears with L161 cylinders this is to be performed within 300 cycles or 
3 calendar months of the issue date of this SB, whichever is the earlier. 
On landing gears (left hand or right hand) where SB 32-JM7862 was first accomplished 
at revision 1 or where inspection to Part 1 of this SB reveals evidence of special washer 
migration, perform an inspection of the MLG cylinder in accordance with Part 2 of this 
SB. For gears with DTD5094 cylinders (see note above) this is to be performed within 
200 cycles or 2 calendar months of the issue date of this SB, whichever is the earlier. 
For gears with L161 cylinders this is to be performed within 600 cycles or 6 calendar 
months of the issue date of this SB, whichever is the earlier. 
NOTE: Part 2 of this SB applies if the forward spig ot bearing cap was ever installed 
with the bearing locking pins facing the special washer (as per SB JM7862 
Revision 1), even if the cap has subsequently been reinstalled with the 
locking pins facing forward and there is no evidence of washer migration. 
For all landing gears, after Part 1 or Part 2 of this SB has been accomplished, perform 
an inspection in accordance with Part 3 of this SB between 4 and 6 calendar weeks or 
between 20 and 30 cycles, whichever is the earlier. 
For any landing gear on which SB 32-JM7862 has not yet been accomplished no 
immediate action is required. 
For all the above calendar and flight cycle limits, whichever occurs first applies. 
The technical content of this SB is approved under the authority of EASA PART 21 
Approval No. EASA.21J.047.

### Page 7

SERVICE BULLETIN  
ORIGINAL ISSUE: 3 rd  October 2014  32-A-JA140940 
  PAGE 5 
 
2. ACCOMPLISHMENT INSTRUCTIONS 
INDEPENDENT INSPECTION 
WHENEVER ANY PART OF THE MAIN OR ASSOCIATED SYSTEM IS DISMANTLED, 
ADJUSTED, REPAIRED OR RENEWED, THAT PART OF THE SYSTEM WHICH HAS 
BEEN DISTURBED SHALL BE SUBJECTED TO AN INDEPENDENT INSPECTION FOR 
SECURITY OF LOCKING DEVICES, FULL AND FREE MOVEMENT, DIRECTION AND 
TENSION CHECKS. THIS WORK MUST BE DONE IN ACCORDANCE WITH THE 
ACCEPTABLE MEANS OF COMPLIANCE M.A. 402 (a) TO EASA PART M, OR TO AN 
EQUIVALENT NATIONAL STANDARD. 
WARNING: MAKE SURE THE AIRCRAFT AND THE AIRCRAFT SY STEMS ARE MADE 
SAFE AS DETAILED IN THE APPLICABLE CHAPTERS OF THE AIRCRAFT 
MAINTENANCE MANUAL. 
WARNING: THE MINIMUM CLEARANCE BETWEEN MOVING AND S TRUCTURAL PARTS 
MUST BE 0.2 IN (5.1 MM) UNLESS OTHERWISE STATED. 
CAUTION: TO AVOID DAMAGE, MAKE SURE BEFORE MOVING C ONTROLS THAT 
CONTROL RUNS AND CONTROL SURFACES ARE FREE FROM 
OBSTRUCTION. 
CAUTION: TAKE CARE NOT TO DAMAGE STRUCTURE WHEN MAT ERIAL IS CUT OR 
DRILLED. REMOVE ALL UNWANTED MATERIAL FROM THE WORK AREA. 
CAUTION: IF AN ELECTRICAL CONNECTION OR CONNECTOR I S DISMANTLED, 
ASSEMBLED OR REPLACED, DO A CONTINUITY CHECK AND, IF 
APPLICABLE, A SCREEN BONDING CHECK BEFORE THE ASSEMBLY IS 
CONNECTED TO EQUIPMENT. 
NOTE: Abbreviations used in the accomplishment inst ructions of this SB are:- 
 AMM - Aircraft Maintenance Manual. 
CMM - Component Maintenance Manual. 
 MLG - Main Landing Gear. 
 MRO - Maintenance, Repair and Overhaul. 
NDT - Non Destructive Test. 
 
A. Preparation 
(1) Refer to AMM 24-00-00 and de-energize the aircr aft bus-bars. 
(2) Gain access to the MLG.

### Page 8

SERVICE BULLETIN  
32-A-JA140940  ORIGINAL ISSUE: 3 rd  October 2014 
PAGE 6   
 
 
B. Accomplishment - Use material kit number JA14094 0 (refer to paragraph 3.A.). 
Part 1 
(1) Refer to Figure 1 Detail B and perform a visual  inspection of the special washer 
installed at the MLG forward spigot for evidence of special washer migration. 
Check that the special washer tab is flush with (no visible gap) and parallel to the 
flat on top of the MLG spigot housing. 
NOTE: It is recommended that, if applicable, the vi sual inspection part of SB 
32-A-JA851226 is carried out concurrently with Part 1 of this SB. 
(2) If the special washer tab is not flush with (vi sible gap) or not parallel to the flat on 
top of the MLG spigot housing, this is evidence that the special washer may have 
migrated and Part 2 of this SB must be performed in accordance with the 
compliance requirements. 
(3) If there is no evidence of special washer migra tion, refer to Figure 1 Detail C and 
apply a small amount of suitable witness paint (such as F-900 Torque Seal or 
Loctite 7414) over the top inboard side edge of the special washer tab and onto 
the flat of the MLG spigot housing. Ensure that the special washer inspection 
window is clean and free from foreign material such as excess gasket. 
(4) Report all findings, including if no evidence o f washer migration is found, to BAE 
Systems on the Operator Report Form attached. 
Part 2  
(1) Refer to AMM 32-10-11, page block 401 and remov e the affected MLG from the 
aircraft. 
(2) Remove and retain bearing p/n 13744B29. 
(3) Locate the forward spigot in the MLG cylinder s ubassembly and remove as 
follows:- 
(a) Remove and discard split-pin. 
(b) Remove slotted nut, spigot bolt and washer. 
(c) Withdraw forward spigot from cylinder. 
(4) Remove the special washer from the leg. 
(5) Remove any remains of gasket material on the wa sher and leg. 
(6) Clean surface of the forward face of the MLG sp igot housing with white spirit or 
equivalent. Visually inspect the forward face of the MLG spigot housing using 10X 
magnification and a bright light for evidence of wear marks that may have been 
caused by migration of the special washer. 
(7) Check the forward face of the MLG spigot housin g using 10X magnification and a 
bright light for evidence corrosion.

### Page 9

SERVICE BULLETIN  
ORIGINAL ISSUE: 3 rd  October 2014  32-A-JA140940 
  PAGE 7 
 
(8) Remove all corrosion and wear marks i.a.w. APPH  (now Heroux Devtek) SB 32-
19 (embedded in BAE Systems SB 32-A-JA851226) which provides instructions 
for the repair of cracks within specified limits. Operators must enquire to Heroux 
Devtek, for any cracks or corrosion in excess of these limits. The contact details 
for Heroux Devtek are as follows:- 
Heroux Devtek, 
Engineering Division, 
Unit 1, 
Pembroke Court, 
Chancellor Road, 
Manor Park, 
Runcorn, 
Cheshire, 
WA7 1TG, 
England. 
FAX (+44) 01928 579626      TEL (+44) 01928 532600 
(9) For cylinders made from DTD5094, perform an NDT  inspection of the MLG spigot 
housing for cracks i.a.w. SB 32-A-JA851226. 
(10) Restore protective treatment on the forward fa ce of the MLG spigot housing using 
Alocrom (or Alodine) 1200. 
NOTE: The aft face of the MLG spigot housing should  have primer and paint 
applied. There has been at least one reported case of primer and paint 
not being applied to this face by a MRO during overhaul of the MLG. 
Check for primer and paint on the aft face. If not applied, inspect for and 
remove any corrosion as for the front face. Restore the full protective 
treatment (Alocrom, primer and paint) i.a.w. with the MLG CMM. 
(11) Visually inspect the special washer for signs of wear and damage. Discard any 
special washer showing signs of wear or damage. 
NOTE: Special washers with wear marks/damage to the  cadmium plating on 
the inner (MLG cylinder facing) must be discarded. 
Special washers with tabs deformed or bent so they are not at 90°  must 
also be discarded.  
(12) Install a new or serviceable special washer p/ n 13744B31 i.a.w. SB 32-JM7862 
Revision 3 or later. 
(13) Re-install forward spigot, bearing and MLG i.a .w. SB 32-JA7862 Revision 3 or 
later. 
(14) Refer to AMM 32-30-00, page block 201 and perf orm undercarriage 
retraction/extension check. 
(15) Refer to Figure 1 Detail C and check that the witness paint between the special 
washer tab and flat of the MLG spigot housing is still intact.

### Page 10

SERVICE BULLETIN  
32-A-JA140940  ORIGINAL ISSUE: 3 rd  October 2014 
PAGE 8   
 
(16) If the paint is broken, report findings to BAE  Systems and await further 
instructions before further flight. 
(17) Report all findings, including if no faults ar e found, to BAE Systems on the 
Operator Report Form attached. 
Part 3 
(1)    Refer to Figure 1 Detail C and check that the witness paint between the special 
washer tab and the flat of the MLG spigot housing is still intact. 
(2)     If the paint is broken, report findings to BAE Systems and await further 
instructions before further flight. 
(3)     Report all findings, including if no faults are found, to BAE Systems on the 
Operator Report Form attached. 
C. Testing 
(1) Not applicable. 
D. Recovery 
(1) Aircraft records:- 
(a) Add SB number “32-A-JA140940” to the aircraft r ecords. 
(2) Inform BAE Systems of the accomplishment of thi s SB using the Accomplishment 
Report attached.

### Page 11 (OCR)

BRITISH AEROSPACE
JETSTREAM
SERIES 3100 & 3200
SERVICE BULLETIN
FWD
REAR SPAR
DATUM
SPECIAL WASHER
TAB FLUSH WITH
TOP OF CYLINDER,
NO VISIBLE GAP  LEFT HAND SHOWN
RIGHT HAND OPPOSITE
ROTATED TAB  BENT TAB  VISIBLE GAP
CORRECT INSTALLATION OF SPECIAL
WASHER LOOKING OUTBOARD ON
LEFT HAND MLG FORWARD SPIGOT
UNACCEPTABLE INSTAI  LATIONS OF SPECIAL
WASHER LOOKING OUTBOARD ON LEFT HAND
MAIN LANDING GEAR (MLG) FORWARD SPIGOT
WITNESS PAINT
OFFSET FROM  CYLINDER (REF)
CENTRELINE
INSPECTION
WINDOW
SPECIAL WASHER
• FORWARD SPIGOT
(REF)
C  J3210022
Inspection of Main Landing Gear Special Washer Installation.
Figure 1
ORIGINAL ISSUE: 3rd October 2014  32-A-JA140940
PAGE 9

### Page 12

SERVICE BULLETIN  
32-A-JA140940  ORIGINAL ISSUE: 3 rd  October 2014 
PAGE 10   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
BLANK PAGE

### Page 13

SERVICE BULLETIN  
ORIGINAL ISSUE: 3 rd  October 2014  32-A-JA140940 
  PAGE 11 
 
3. MATERIAL INFORMATION 
NOTE: The new part numbers shown in paragraph 3.A. are necessary to accomplish this SB  
on one aircraft. Use the material kit number shown to order the parts. 
A. New parts supplied as a material kit - order kit  number JA140940. 
New Part No. QTY Keyword Old Part No. 
13744B31 2 Special washer 13744B31 
NOTE: The special washer may require modification p rior to installation 
(see SB 32-JA7862 Revision 3 or later). 
B. Materials required - Operators Supply 
Material No. QTY Keyword 
- A/R Alocrom (or Alodine) 1200 
- A/R White spirit or equivalent 
- A/R Epoxy primer 
- A/R Polyurethane paint 
- A/R 
F-900 Torque Seal 
Alternative 
Loctite 7414

### Page 14

SERVICE BULLETIN  
32-A-JA140940  ORIGINAL ISSUE: 3 rd  October 2014 
PAGE 12   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
BLANK PAGE

### Page 15

SERVICE BULLETIN  
ORIGINAL ISSUE: 3 rd  October 2014  32-A-JA140940 
  PAGE 13 
 
4. CONTINUED AIRWORTHINESS 
A. Continued Airworthiness Instructions 
The following information is provided to Operators to permit continued operation of the aircraft 
pending receipt of a formal revision to the relevant aircraft manuals. 
B. Scheduled Maintenance 
(1) Not applicable. 
C. Removal Procedures 
(1) Refer to part 2.B. of this SB. 
NOTE: Removal is the reverse of installation. 
D. Installation Procedures 
(1) Refer to part 2.B. of this SB. 
E. Test Procedures 
(1) Not applicable. 
F. Trouble Shooting 
(1) Not applicable.

### Page 16

SERVICE BULLETIN  
32-A-JA140940  ORIGINAL ISSUE: 3 rd  October 2014 
PAGE 14   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
BLANK PAGE

### Page 17

abcd 
 
OPERATOR REPORT FORM 
 
This Operator Report Form is required to be completed and returned to:- 
BAE SYSTEMS Regional Aircraft, 
Customer Engineering Liaison, 
Building 37, 
Prestwick International Airport, 
Ayrshire KA9 2RW, 
SCOTLAND. 
Tel. No. +44 (0)1292 67 5276. 
FAX. No. +44 (0)1292 67 5700. 
Title Landing Gear – Inspection of Main Landing Gea r Special Washer Installation. 
Service Bulletin no.  Operator Maintenance 
Organisation 
name, e-mail 
and phone no. 
Aircraft 
Registration and 
Constructors no.  
Flying Hours No. of 
Landings 
32-A-JA140940  
     
 
Findings/comments for Left and Right Hand MLGs in relation to each of Parts 1, 2 and 3 of this SB. 
 
Part 1 - Any evidence of migration of the special washer installed at the left/right MLG forward spigot? 
 
 
 
Part 2 - Any corrosion or wear marks on the forward face of the left/right MLG spigot housing and if so  
to what extent? 
 
 
 
 
 
Part 3 - Any evidence of migration of the special washer installed at the left/right MLG forward spigot?

### Page 18

(No text on this page.)

### Page 19

abcd 
 
 
ACCOMPLISHMENT REPORT 
 
 
 
SERVICE BULLETIN NUMBER  32-A-JA140940 
 
TITLE: LANDING GEAR – INSPECTION OF MAIN LANDING GE AR SPECIAL WASHER 
INSTALLATION. 
 
TO: BUSINESS SUPPORT TEAM, 
 TECHNICAL PUBLICATIONS, 
 BAE SYSTEMS (OPERATIONS) LIMITED, 
 PRESTWICK INTERNATIONAL AIRPORT, 
 AYRSHIRE, KA9 2RW, 
 SCOTLAND. 
 
 Telephone: (01292) 675207 
 Fax:  (01292) 675704 
 E-mail: RAPublications@baesystems.com 
 
PLEASE BE ADVISED THAT THE ABOVE SERVICE BULLETIN HAS BEEN EMBODIED ON 
AIRCRAFT CONSTRUCTORS NUMBER(S): 
 
 
WE REQUEST THE APPROPRIATE REVISIONS TO APPLICABLE MANUALS. 
 
NAME:  ...........….................................................................... 
 
SIGNED:  ............................................................................... 
 
COMPANY:  ...............…........................................................ 
 
DATE:  ..................................................…............................. 
 
 
 
SERVICE BULLETIN COMMENTS/FEEDBACK. 
 
Please report any non-technical comments or inaccuracies regarding this service bulletin to the 
above address.

### Page 20

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
