# BAE Systems Service Bulletin 32-JM7862: Revision 1

- Rights: © BAE Systems. Filed by the FAA in regulations.gov docket FAA-2013-1012; AD 2014-06-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [BAE Systems Service Bulletin 32-JM7862](https://openairdocs.org/service-documents/bae-systems/32-jm7862.md)
- Title as filed: U.S. DOT/FAA - 32-JM7862
- Pages: 17
- PDF: https://openairdocs.org/files/sha256/12/98/1298f679a4b934872dfef1c55dd9da95683ddc793c126755599a6bb651ab3ac0
- Page: https://openairdocs.org/service-documents/bae-systems/32-jm7862/file/1298f679a4b9

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ORIGINAL ISSUE: 8th April 2013  32-JM7862 
REVISION 1: 7th May 2013  PAGE 1 OF 14 
 
 
 
BAE SYSTEMS (OPERATIONS) LIMITED, 
PRESTWICK INTERNATIONAL AIRPORT, 
AYRSHIRE, KA9 2RW, 
SCOTLAND. 
32-JM7862 
TITLE: LANDING GEAR - INTRODUCTION OF SPECIAL WASHER TO PROTECT THE MAIN 
LANDING GEAR CYLINDER AT THE FORWARD SPIGOT. 
MODIFICATION NUMBER JM7862 
1. PLANNING INFORMATION 
A. Effectivity 
All Jetstream Series 3100 and 3200. 
B. Reason 
On Series 3100 aircraft, which did not have L161 material Main Landing Gear (MLG) 
cylinders (Service Bulletin 32-JA880340) there have been cases of MLG cylinder stress 
corrosion cracking (including failure) originating at the forward face of the cylinder 
around the gear mounting spigot (yoke pintle housing). The protective treatments in this 
area can be damaged by rubbing against the spigot bearing in the gear attachment 
structure in the wing during gear retraction and extension, thereby allowing stress 
corrosion cracking to initiate. 
Although all Series 3200 aircraft have L161 material MLG cylinders, accomplishment of 
this Service Bulletin (SB) additionally includes Series 3200 aircraft. This will reduce 
scrappage rates at overhaul and maintain commonality of parts and installation method 
with Series 3100 aircraft. 
C. Description 
This SB introduces a special washer fitted at the forward spigot on both left and right 
MLGs. The washer is attached to the forward and top faces of the MLG cylinder spigot 
housing using an anaerobically curing, low adhesion, liquid gasket.  
To accommodate the thickness of the new washer, a new spigot split bearing with 
reduced flange thickness is also introduced by this SB.

### Page 2

32-JM7862  ORIGINAL ISSUE: 8th April 2013 
PAGE 2  REVISION 1: 7th May 2013 
 
The tasks are as follows: 
- De-energize aircraft bus-bars. 
- Remove MLG. 
- Remove forward spigot. 
- Inspect (NDT) spigot (pintle) housing for cracks, if applicable. 
- Restore protective treatment, if necessary. 
- Install new special wash er. 
- Reinstall forward spigot. 
- Replace forward split bearing. 
- Rei nstall MLG and perform functional test. 
- Amend aircraft records. 
D. Manpower 
15 man-hours. 
Mechanical skills are necessary. 
E. Material - Cost and Availability 
Cost and availability is by arrangement between the Operator and BAE SYSTEMS. 
F. Tooling - Price and Availability 
Not applicable. 
G. Weight and Balance 
Not affected. 
H. Aircraft Noise Levels 
Not affected. 
I. Electrical Load Data 
Not affected. 
J. Software Accomplishment Summary 
Not applicable. 
K. Referenc es 
-  Aircraft Maintenance Manual Chapters 24-00-00, 32-10-11 and 32-30-00. 
- SB 32-A-JA851226. 
- SRM 51- 10-31.

### Page 3 (OCR)

BRITISH AEROSPACE
JETSTREAM
SERIES 7100 & 3200
SERVICE BULLETIN
L.  Publications Affected
- Illustrated Parts Catalogue.
- Aircraft Maintenance Manual.
Operators are requested to advise:-
The Business Support Team,
Technical Publications,
BAE SYSTEMS (Operations) Limited,
Prestwick International Airport,
Ayrshire,
KA9 2RW,
SCOTLAND,
of the accomplishment of this SB and request the necessary revisions for the affected
manuals.
M.  Family Tree Of Modification Relationships
Not applicable.
N. Approval
The technical content of this SB is the subject of EASA Airworthiness Directive
consultation.
Compliance with this SB must be achieved as follows:-
For all aircraft after 31s of July 2013, at the next scheduled removal of the affected MLG
(left or right).
NOTE: For Jetstream Series 3100 aircraft that are affected by inspection SB 32-A-
JA851226, next scheduled MLG removal may be for NDT inspection or overhaul.
NOTE: For Jetstream Series 3100 aircraft that are not affected by inspection SB 32-A-
JA851226, next scheduled MLG removal would be for overhaul.
NOTE: For Jetstream Series 3200 aircraft, next scheduled MLG removal would be for
overnaul.
The technical content of this SB is approved under the authority of EASA PART 21
Approval No. EASA.21J.047.
Signed
Date  7/5/13
EASA Part 21 Approval No. EASA.21J.047.
ORIGINAL ISSUE: 8th April 2013  32-JM7862
REVISION 1: 7th May 2013  PAGE 3

### Page 4

32-JM7862  ORIGINAL ISSUE: 8th April 2013 
PAGE 4  REVISION 1: 7th May 2013 
 
 
 
 
 
 
 
 
 
 
 
 
 
BLANK PAGE

### Page 5

ORIGINAL ISSUE: 8th April 2013  32-JM7862 
REVISION 1: 7th May 2013  PAGE 5 
 
2. ACCOMPLISHMENT INSTRUCTIONS 
INDEPENDENT INSPECTION 
WHENEVER ANY PART OF THE MAIN OR ASSOCIATED SYSTEM IS DISMANTLED, 
ADJUSTED, REPAIRED OR RENEWED, THAT PART OF THE SYSTEM WHICH HAS 
BEEN DISTURBED SHALL BE SUBJECTED TO AN INDEPENDENT INSPECTION FOR 
SECURITY OF LOCKING DEVICES, FULL AND FREE MOVEMENT, DIRECTION AND 
TENSION CHECKS. THIS WORK MUST BE DONE IN ACCORDANCE WITH THE 
ACCEPTABLE MEANS OF COMPLIANCE M.A. 402 (a) TO EASA PART M, OR TO AN 
EQUIVALENT NATIONAL STANDARD. 
WARNING: MAKE SURE THE AIRCRAFT AND THE AIRCRAFT SYSTEMS ARE MADE 
SAFE AS DETAILED IN THE APPLICABLE CHAPTERS OF THE AIRCRAFT 
MAINTENANCE MANUAL. 
WARNING: THE MINIMUM CLEARANCE BETWEEN MOVING AND STRUCTURAL PARTS 
MUST BE 0.2 IN (5.1 MM) UNLESS OTHERWISE STATED. 
CAUTION: TO AVOID DAMAGE, MAKE SURE BEFORE MOVING CONTROLS THAT 
CONTROL RUNS AND CONTROL SURFACES ARE FREE FROM 
OBSTRUCTION. 
CAUTION: TAKE CARE NOT TO DAMAGE STRUCTURE WHEN MATERIAL IS CUT OR 
DRILLED. REMOVE ALL UNWANTED MATERIAL FROM THE WORK AREA. 
CAUTION: IF AN ELECTRICAL CONNECTION OR CONNECTOR IS DISMANTLED, 
ASSEMBLED OR REPLACED, DO A CONTINUITY CHECK AND, IF 
APPLICABLE, A SCREEN BONDING CHECK BEFORE THE ASSEMBLY IS 
CONNECTED TO EQUIPMENT. 
NOTE: Abbreviations used in the accomplishment instructions of this SB are:- 
 AMM - Aircraft Maintenance Manual. 
 MLG – Main Landing Gear. 
 NDT – Non Destructive Test. 
 
A. Preparation 
(1) Refer to AMM 24- 00-00 and de-energize the aircraft bus-bars. 
 
B. Accomplishment - Use material kit number JM7862 (refer to paragraph 3A). 
NOTE:   The following accomplishment instructions are in two parts, one for the left 
MLG and the other for the right MLG. Both MLGs do not have to be modified at 
the same time. The modification and SB should only be claimed when both 
MLGs have been modified.

### Page 6

32-JM7862  ORIGINAL ISSUE: 8th April 2013 
PAGE 6  REVISION 1: 7th May 2013 
 
Left MLG 
(1) Refer to AMM 32-10-11 page block 401 and remove the left MLG.  
(2) Locate the forward spigot in the MLG cylinder subassembly and remove as 
follows:- 
(a) Remove and discard split-pin. 
(b) Remove slotted nut, spigot bolt and washer. 
(c) Withdraw forward spigot from cylinder. 
(3) Remove any paint or primer from the forward face of the MLG spigot housing in 
accordance with SRM 51-10-31. 
(4) Refer to SB 32-A-JA851226 and, if applicable, do a NDT inspection of the MLG 
spigot (pintle) housing for cracks. 
(5) Check the condition of the forward face of the MLG spigot housing and, if 
necessary, restore protective treatment using Alocrom (or Alodine) 1200. Do not 
apply primer or paint. 
(6) Refer to figure 1 view D. Position the special washer p/n 13744B31 (item 1) over 
the spigot housing bore and mark the inside face of the washer to show the 
material to be removed to enable the washer to match the bottom of the bore.  
(7) Refer to figure 1 view D. Trim the new special washer p/n 13744B31 (item 1). 
NOTE : Only a small amount of material should need to be removed to allow fitment of 
the special washer on Series 3100 landing gears. For Series 3200 landing 
gears, up to 0.080 in. of material may need to be removed. The base material 
of the washer is corrosion resistant steel. So, there is no need to reprotect the 
trimmed edge. Take care not to damage the protective treatment on the inside 
and outside faces of the washer. 
(8) Refer to figure 1 and install the new special washer p/n 13744B31 (item 1) as 
follows:- 
(a) In accordance with the manufacturer’s instructions, apply Loctite 5203 liquid 
gasket to the inside faces of the special washer. 
(b) Clamp the special washer to the forward face of the cylinder whilst the 
gasket cures. 
NOTE : Liquid gasket cure time is 24 hours at 20 Deg C or 30 mins if hot air not 
exceeding 120 Deg C is applied. 
(c) Remove any excess, particularly at the top, forward edge of the cylinder. 
(9) Reinstall the forward spigot in the MLG cylinder subassembly as follows:- 
(a) Reinstall forward spigot in cylinder subassembly.

### Page 7

ORIGINAL ISSUE: 8th April 2013  32-JM7862 
REVISION 1: 7th May 2013  PAGE 7 
 
(b) Install spigot bolt, washer and slotted nut, with the slotted nut on the 
retraction side of the cylinder. 
(c) Tighten bolt with a maximum torque of 30 lbf inch (3.4 Nm) using a suitable 
wrench. 
(d) Lock slotted nut with new split-pin p/n SP90C8. 
(e) Coat head and nut of spigot bolt with sealing compound to AMS-S-8802 or 
DTD 900/4502 (PR1422A2). 
(10) Refer to figure 1 and discard the forward split bearing p/n 13744B11 and replace 
with new bearing p/n 13744B29 (item 2) as shown. 
(11) Refer to AMM 32- 10-11 page block 401 and reinstall the left MLG. 
Right MLG 
(1) Refer to AMM 32-10-11 page block 401 and remove the right MLG.  
(2) Locate the forward spigot in the MLG cylinder subassembly and remove as 
follows:- 
(a) Remove and discard split-pin. 
(b) Remove slotted nut, spigot bolt and washer. 
(c) Withdraw forward spigot from cylinder. 
(3) Remove any paint or primer from the forward face of the MLG spigot housing in 
accordance with SRM 51-10-31. 
(4) Refer to SB 32-A-JA851226 and, if applicable, do a NDT inspection of  the MLG 
spigot (pintle) housing for cracks. 
(5) Check the condition of the forward face of the MLG spigot housing and, if 
necessary, restore protective treatment using Alocrom (or Alodine) 1200. Do not 
apply primer or paint. 
(6) Refer to figure 1 view D. Position the special washer p/n 13744B31 (item 1) over 
the spigot housing bore and mark the inside face of the washer to show the 
material to be removed to enable the washer to match the bottom of the bore. 
(7) Refer to figure 1 view D. Trim the new special washer p/n 13744B31 (item 1). 
NOTE : Only a small amount of material should need to be removed to allow fitment of 
the special washer on Series 3100 landing gears. For Series 3200 landing 
gears, up to 0.080 in. of material may need to be removed. The base material 
of the washer is corrosion resistant steel. So, there is no need to reprotect the 
trimmed edge. Take care not to damage the protective treatment on the inside 
and outside faces of the washer. 
(8) Refer to figure 1 and install the new special washer p/n 13744B31 (item 1) as 
follows:-

### Page 8

32-JM7862  ORIGINAL ISSUE: 8th April 2013 
PAGE 8  REVISION 1: 7th May 2013 
 
(a) In accordance with the manufacturer’s instructions, apply Loctite 5203 liquid 
gasket to the inside faces of the special washer. 
(b) Clamp the special washer to the forward face of the cylinder whilst the 
gasket cures. 
NOTE : Liquid gasket cure time is 24 hours at 20 Deg C or 30 mins if hot air not 
exceeding 120 Deg C is applied. 
(c) Remove any excess, particularly at the top, forward edge of the cylinder. 
(9) Reinstall the forward spigot in the MLG cylinder subassembly as follows:- 
(a) Reinstall forward spigot in cylinder subassembly. 
(b) Install spigot bolt, washer and slotted nut, with the slotted nut on the 
retraction side of the cylinder. 
(c) Tighten bolt with a maximum torque of 30 lbf inch (3.4 Nm) using a suitable 
wrench. 
(d) Lock slotted nut with new split-pin p/n SP90C8. 
(e) Coat head and nut of spigot bolt with sealing compound to AMS-S-8802 or 
DTD 900/4502 (PR1422A2). 
(10) Refer to figure 1 and discard the forward split bearing p/n 13744B11 and replace 
with new bearing p/n 13744B29 (item 2) as shown. 
(11) Refer to AMM 32- 10-11 page block 401 and reinstall the right MLG. 
C. Testing 
(1) Refer to AMM 32- 30-00 page block 201 and do a functional test of the MLG. 
D. Recovery 
(1) Aircraft records:- 
(a) Add SB number “ 32-JM7862 Left” and/or “32-JM7862 Right” to the aircraft 
records as appropriate. 
(b) When both the left and right MLGs have been modified, add modification 
number JM7862 to the aircraft records.

### Page 9

ORIGINAL ISSUE: 8th April 2013  32-JM7862 
REVISION 1: 7th May 2013  PAGE 9 
 
NOTE: Operators are reminded of the necessity to inform:- 
The Business Support Team, 
Technical Publications, 
BAE SYSTEMS (Operations) Limited, 
Prestwick International Airport, 
Ayrshire, 
KA9 2RW, 
SCOTLAND, 
of the accomplishment of this SB in order to obtain the necessary revisions for the 
affected manuals, see paragraph 1.L. Publications Affected, of this SB.

### Page 10 (OCR)

BRITISH AEROSPACE
JETSTREAM
SERIES 3100 & 3200
SERVICE BULLETIN
FWD
REAR SPAR
DATUM
SPECIAL
WASHER
13744B31
LEFT HAND SHOWN
RIGHT HAND OPPOSITE
SPLIT
BEARING
13744B29
FORWARD
SPIGOT  REMOVE MATERIAL FROM  BEARING
HOUSING BORE  WASHER TO MATCH  JOURNAL
(SHOWN DOTTED)  SPIGOT HOUSING BORE  SECTION 'C-C'  (REF)  SECTION 'C-C'
PRE MOD JM5218  POST MOD JM5218
WASHER OMMITED FOR CLARITY  WASHER OMMITED FOR CLARITY
J3210019
INSTALLATION OF SPECIAL WASHER AND NEW BEARING
FIGURE 1
32-JM7862  ORIGINAL ISSUE: 8th April 2013
PAGE 10  REVISION 1: 7th May 2013

### Page 11

ORIGINAL ISSUE: 8th April 2013  32-JM7862 
REVISION 1: 7th May 2013  PAGE 11 
 
3. MATERIAL INFORMATION 
NOTE: The new part numbers shown in paragraph 3.A. are necessary to accomplish this SB  
on one aircraft.  Use the material kit number shown to order the parts. 
A. New parts supplied as a material kit - order kit number JM7862. 
New Part No. QTY Keyword Old Part No. 
13744B31 2 Special washer - 
13744B29 2 Bearing 13744B11 
B. Materials required - Operators Supply 
Material No. QTY Keyword 
- A/R Alocrom (or Alodine) 1200 
- A/R Loctite 5203 liquid gasket 
SP90C8 2 Split pin 
PR1422A2 A/R Sealing compound

### Page 12

32-JM7862  ORIGINAL ISSUE: 8th April 2013 
PAGE 12  REVISION 1: 7th May 2013 
 
 
 
 
 
 
 
 
 
 
 
 
 
BLANK PAGE

### Page 13

ORIGINAL ISSUE: 8th April 2013  32-JM7862 
REVISION 1: 7th May 2013  PAGE 13 
 
4. CONTINUED AIRWORTHINESS 
A. Continued Airworthiness Instructi ons 
The following information is provided to Operators to permit continued operation of the aircraft 
pending receipt of a formal revision to the relevant aircraft manuals. 
B. Scheduled Maintenance 
(1) Not applicable. 
C. Removal Procedures 
(1) Refer to part 2.B of this S B. 
NOTE: Removal is the reverse of installation. 
D. Installation Procedures 
(1) Refer to part 2.B of this SB. 
E. Test Procedures 
(1) Refer to part 2.C of this SB. 
F. Trouble Shooting 
(1) Not applicable.

### Page 14

(No text on this page.)

### Page 15

ACCOMPLISHMENT REPORT 
 
 
 
SERVICE BULLETIN NUMBER 32-JM7862 
 
TITLE: LANDING GEAR - INTRODUCTION OF SPECIAL WASHER TO PROTECT THE MAIN 
LANDING GEAR CYLINDER AT THE FORWARD SPIGOT. 
 
TO: THE BUSINESS SUPPORT TEAM, 
 TECHNICAL PUBLICATIONS, 
 BAE SYSTEMS (OPERATIONS) LIMITED, 
 PRESTWICK INTERNATIONAL AIRPORT, 
 AYRSHIRE, KA9 2RW, 
 SCOTLAND. 
 
 Telephone: (01292) 675207 
 Fax:  (01292) 675704 
 E- mail: RAPublications@baesystems.com 
 
PLEASE BE ADVISED THAT THE ABOVE SERVICE BULLETIN HAS BEEN EMBODIED ON 
AIRCRAFT CONSTRUCTORS NUMBER(S): 
 
 
WE REQUEST THE APPROPRIATE REVISIONS TO APPLICABLE MANUALS. 
 
NAME:  ...........….................................................................... 
 
SIGNED:  ............................................................................... 
 
COMPANY:  ...............…........................................................ 
 
DATE:  ..................................................…............................. 
 
 
 
SERVICE BULLETIN COMMENTS/FEEDBACK. 
 
Please report any non-technical comments or inaccuracies regarding this service bulletin to the 
above address.

### Page 16

(No text on this page.)

### Page 17

ORIGINAL ISSUE: 7th May 2013  32-JM7862 
  PAGE 1 OF 1 
 
 
 
BAE SYSTEMS (OPERATIONS) LIMITED, 
PRESTWICK INTERNATIONAL AIRPORT, 
AYRSHIRE, KA9 2RW, 
SCOTLAND. 
32-JM7862 
 
 
TRANSMITTAL SHEET 
 
This page transmits Revision 1 of Service Bulletin 32-JM7862, pages 1 to 13. 
 
 
TITLE: LANDING GEAR - INTRODUCTION OF SPECIAL WASHER TO PROTECT THE MAIN 
LANDING GEAR CYLINDER AT THE FORWARD SPIGOT. 
MODIFICATION NUMBER JM7862 
NOTE: Aircraft with modification JM7862 embodied still require to be inspected in acordance with 
SB 32-A-JA851226. 
 
REASON FOR ISSUE 
 
To embody the following changes as a result of Proof Installation: 
 
Para 1 N. third sentence revised to include ‘after 31st of July 2013’. 
Paras 2 B.(6) and (7) plus NOTE added to Left and Right MLG accomplishment to detail 
modification of special washer p/n 13744B31 which compensates for variations in spigot housing 
thickness between J31 and J32 aircraft. 
Para 2 B. (8) has NOTE added to detail cure times for liquid gasket. 
Figure 1 has view added showing area of special washer p/n 13744B31 where material is removed 
to match spigot housing bore. 
 
INSTRUCTION FOR INCORPORATION 
 
Insert Service Bulletin at Revision 1.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
