# BAE Systems Service Bulletin 32-JM7862: SB 32-JM7862 Rev 3

- Rights: © BAE Systems. Filed by the FAA in regulations.gov docket FAA-2014-1093, the docket of AD 2015-06-01. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [BAE Systems Service Bulletin 32-JM7862](https://openairdocs.org/service-documents/bae-systems/32-jm7862.md)
- Title as filed: SB 32-JM7862 Rev 3
- Pages: 20
- PDF: https://openairdocs.org/files/sha256/65/67/65677c1bd11381cb93fe7cd80336b1f60db65bf2c6c6309f8da5d42bb196b9ac
- Page: https://openairdocs.org/service-documents/bae-systems/32-jm7862/file/65677c1bd113

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ORIGINAL ISSUE: 8 th  April 2013  32-JM7862 
REVISION 3: 3 rd  October 2014  PAGE 1 OF 1 
 
 
SERVICE BULLETIN
 
BAE SYSTEMS (OPERATIONS) LIMITED, 
PRESTWICK INTERNATIONAL AIRPORT, 
AYRSHIRE, KA9 2RW, 
SCOTLAND. 
32-JM7862 
 
TRANSMITTAL SHEET 
This page transmits revision 3 of Service Bulletin 32-JM7862, pages 1 to 16. 
TITLE: LANDING GEAR - INTRODUCTION OF SPECIAL WASHE R TO PROTECT THE MAIN 
LANDING GEAR CYLINDER AT THE FORWARD SPIGOT. 
MODIFICATION NUMBER JM7862 
NOTE: Aircraft with modification JM7862 embodied st ill require to be inspected in accordance with 
SB 32-A-JA851226. 
REASONS FOR ISSUE 
Revision 3 describes improvements to the installation method for the special washer and corrosion 
protection of the MLG cylinder. Editorial. 
Part  1.N -  Amended to refer to SB 32-A-JA140940 for landing gear on which this SB has already 
been accomplished. 
Part 2 - Left and Right MLG 
Step 2.B.(7) - Special washer modification instructions added. 
Step 2.B.(8)(c) - Amended to clarify removal of excess gasket material. 
Step 2.B.(8)(d) - New step to describe application of witness paint. 
Step 2.B.(8)(e) - New step to describe protection of exposed surface of forward spigot housing. 
Step 2.B.(11) - New step to check bearing locking pins for signs of wear or damage to heads. 
Part 2.C - Part 2.C deleted as no longer required. Subsequent Parts re-numbered. 
Figure 1 - Amended to show required gap between special washer tab and MLG cylinder flat. 
Figure 2 - New figure showing witness paint application, MLG spigot housing protection and bearing 
locking pin repair. 
Part 3 - Operator supplied materials added. 
FOR ANY LANDING GEAR ON WHICH THIS SERVICE BULLETIN HAS ALREADY BEEN 
ACCOMPLISHED, SB 32-A-JA140940 SHALL ALSO BE ACCOMPLISHED. 
 
INSTRUCTIONS FOR INCORPORATION 
Remove and discard Service Bulletin at revision 2. 
Insert Service Bulletin at revision 3.

### Page 2

(No text on this page.)

### Page 3

ORIGINAL ISSUE: 8 th  April 2013  32-JM7862 
REVISION 3: 13 th  3rd  October 2014  PAGE 1 OF 16 
 
 
SERVICE BULLETIN
 
BAE SYSTEMS (OPERATIONS) LIMITED, 
PRESTWICK INTERNATIONAL AIRPORT, 
AYRSHIRE, KA9 2RW, 
SCOTLAND. 
32-JM7862 
TITLE: LANDING GEAR - INTRODUCTION OF SPECIAL WASHE R TO PROTECT THE MAIN 
LANDING GEAR CYLINDER AT THE FORWARD SPIGOT. 
MODIFICATION NUMBER JM7862 
1. PLANNING INFORMATION 
A. Effectivity 
All Jetstream Series 3100 and 3200. 
B. Reason 
On Series 3100 aircraft, which did not have L161 material Main Landing Gear (MLG) 
cylinders (Service Bulletin 32-JA880340) there have been cases of MLG cylinder stress 
corrosion cracking (including failure) originating at the forward face of the cylinder 
around the gear mounting spigot (yoke pintle housing). The protective treatments in this 
area can be damaged by rubbing against the spigot bearing in the gear attachment 
structure in the wing during gear retraction and extension, thereby allowing stress 
corrosion cracking to initiate. 
Although all Series 3200 aircraft have L161 material MLG cylinders, accomplishment of 
this Service Bulletin (SB) additionally includes Series 3200 aircraft. This will reduce 
scrappage rates at overhaul and maintain commonality of parts and installation method 
with Series 3100 aircraft. 
C. Description 
This SB introduces a special washer fitted at the forward spigot on both left and right 
MLGs. The washer is attached to the forward and top faces of the MLG cylinder spigot 
housing using an anaerobically curing, low adhesion, liquid gasket.  
To accommodate the thickness of the new washer, a new spigot split bearing with 
reduced flange thickness is also introduced by this SB.

### Page 4

SERVICE BULLETIN  
32-JM7862  ORIGINAL ISSUE: 8 th  April 2013 
PAGE 2  REVISION 3: 3 rd  October 2014 
 
The tasks are as follows: 
- De-energize aircraft bus-bars. 
- Remove MLG. 
- Remove forward spigot. 
- Inspect (NDT) spigot (pintle) housing for cracks,  if applicable. 
- Restore protective treatment, if necessary. 
- Install new special washer. 
- Reinstall forward spigot. 
- Replace forward split bearing. 
- Reinstall MLG and perform functional test. 
- Amend aircraft records. 
- Inform BAE Systems of the accomplishment of this SB. 
D. Manpower 
15 man-hours. 
Mechanical skills are necessary. 
E. Material - Cost and Availability 
Cost and availability is by arrangement between the Operator and BAE SYSTEMS. 
F. Tooling - Price and Availability 
Not applicable. 
G. Weight and Balance 
Not affected. 
H. Aircraft Noise Levels 
Not affected. 
I. Electrical Load Data 
Not affected. 
J. Software Accomplishment Summary 
Not applicable. 
K. References 
-  Aircraft Maintenance Manual Chapters 24-00-00, 3 2-10-11 and 32-30-00. 
- SB 32-A-JA140940. 
- SB 32-A-JA851226. 
- SRM 51-10-31. 
- MLG CMM.

### Page 5

SERVICE BULLETIN  
ORIGINAL ISSUE: 8 th  April 2013  32-JM7862 
REVISION 3: 3 rd  October 2014  PAGE 3 
 
L. Publications Affected 
-  Illustrated Parts Catalogue. 
-  Aircraft Maintenance Manual. 
 
Operators are requested to advise:- 
Business Support Team, 
Technical Publications, 
BAE SYSTEMS (Operations) Limited, 
Prestwick International Airport, 
Ayrshire, 
KA9 2RW, 
SCOTLAND, 
of the accomplishment of this SB and request the necessary revisions for the affected 
manuals. 
M. Family Tree Of Modification Relationships 
Not applicable. 
N. Approval 
The technical content of this SB is the subject of EASA Airworthiness Directive 
consultation. 
Compliance with this SB must be achieved as follows:- 
For all aircraft after 31 st  of July 2013, at the next scheduled removal of the affected MLG 
(left or right). 
NOTE: For Jetstream Series 3100 aircraft that are affected by inspection SB 32-A-
JA851226, next scheduled MLG removal may be for NDT inspection or overhaul. 
NOTE: For Jetstream Series 3100 aircraft that are not affected by inspection SB 32-A-
JA851226, next scheduled MLG removal would be for overhaul. 
NOTE: For Jetstream Series 3200 aircraft, next scheduled MLG removal would be for 
overhaul. 
For any landing gear on which this SB has already been accomplished,  
SB 32-A-JA140940 shall also be accomplished. 
The technical content of this SB is approved under the authority of EASA PART 21 
Approval No. EASA.21J.047. 
.

### Page 6

SERVICE BULLETIN  
32-JM7862  ORIGINAL ISSUE: 8 th  April 2013 
PAGE 4  REVISION 3: 3 rd  October 2014 
 
 
BLANK PAGE

### Page 7

SERVICE BULLETIN  
ORIGINAL ISSUE: 8 th  April 2013  32-JM7862 
REVISION 3: 3 rd  October 2014  PAGE 5 
 
2. ACCOMPLISHMENT INSTRUCTIONS 
INDEPENDENT INSPECTION 
WHENEVER ANY PART OF THE MAIN OR ASSOCIATED SYSTEM IS DISMANTLED, 
ADJUSTED, REPAIRED OR RENEWED, THAT PART OF THE SYSTEM WHICH HAS 
BEEN DISTURBED SHALL BE SUBJECTED TO AN INDEPENDENT INSPECTION FOR 
SECURITY OF LOCKING DEVICES, FULL AND FREE MOVEMENT, DIRECTION AND 
TENSION CHECKS. THIS WORK MUST BE DONE IN ACCORDANCE WITH THE 
ACCEPTABLE MEANS OF COMPLIANCE M.A. 402 (a) TO EASA PART M, OR TO AN 
EQUIVALENT NATIONAL STANDARD. 
WARNING: MAKE SURE THE AIRCRAFT AND THE AIRCRAFT SY STEMS ARE MADE 
SAFE AS DETAILED IN THE APPLICABLE CHAPTERS OF THE AIRCRAFT 
MAINTENANCE MANUAL. 
WARNING: THE MINIMUM CLEARANCE BETWEEN MOVING AND S TRUCTURAL PARTS 
MUST BE 0.2 IN (5.1 MM) UNLESS OTHERWISE STATED. 
CAUTION: TO AVOID DAMAGE, MAKE SURE BEFORE MOVING C ONTROLS THAT 
CONTROL RUNS AND CONTROL SURFACES ARE FREE FROM 
OBSTRUCTION. 
CAUTION: TAKE CARE NOT TO DAMAGE STRUCTURE WHEN MAT ERIAL IS CUT OR 
DRILLED. REMOVE ALL UNWANTED MATERIAL FROM THE WORK AREA. 
CAUTION: IF AN ELECTRICAL CONNECTION OR CONNECTOR I S DISMANTLED, 
ASSEMBLED OR REPLACED, DO A CONTINUITY CHECK AND, IF 
APPLICABLE, A SCREEN BONDING CHECK BEFORE THE ASSEMBLY IS 
CONNECTED TO EQUIPMENT. 
NOTE: Abbreviations used in the accomplishment inst ructions of this SB are:- 
 AMM - Aircraft Maintenance Manual. 
CMM - Component Maintenance Manual. 
 MLG - Main Landing Gear. 
 NDT - Non Destructive Test. 
SRM - Structural Repair Manual. 
 
A. Preparation 
(1) Refer to AMM 24-00-00 and de-energize the aircr aft bus-bars. 
 
B. Accomplishment - Use material kit number JM7862 (refer to paragraph 3.A.). 
NOTE:   The following accomplishment instructions are in two parts, one for the left 
MLG and the other for the right MLG. Both MLGs do not have to be modified at 
the same time. The modification and SB should only be claimed when both 
MLGs have been modified.

### Page 8

SERVICE BULLETIN  
32-JM7862  ORIGINAL ISSUE: 8 th  April 2013 
PAGE 6  REVISION 3: 3 rd  October 2014 
 
Left MLG 
(1) Refer to AMM 32-10-11, page block 401 and remov e the left MLG.  
(2) Locate the forward spigot in the MLG cylinder s ubassembly and remove as 
follows:- 
(a) Remove and discard split-pin. 
(b) Remove slotted nut, spigot bolt and washer. 
(c) Withdraw forward spigot from cylinder. 
(3) Remove any paint or primer from the forward fac e of the MLG spigot housing in 
accordance with SRM 51-10-31. 
(4) Refer to SB 32-A-JA851226 and, if applicable, d o an NDT inspection of the MLG 
spigot (pintle) housing for cracks. 
(5) Check the condition of the forward face of the MLG spigot housing and, if 
necessary, restore protective treatment using Alocrom (or Alodine) 1200. Do not 
apply primer or paint. 
(6) Refer to figure 1 detail D. Position the specia l washer p/n 13744B31 over the 
spigot housing bore and mark the inside face of the washer to show the material 
to be removed to enable the washer to match the bottom of the bore.  
(7) Carefully trim material from the bottom inside diameter of the special washer  p/n 
13744B31 sufficient to create a gap of 0.002 to 0.005 in. (0.051 to 0.127 mm) 
between the special washer tab and the top flat surface of the MLG spigot 
housing when assembled with the forward spigot pin. Take care not to remove 
excessive material. If the gap is greater than 0.005 in. (0.127 mm), the special 
washer must be discarded. 
(8) Refer to figure 1 and install the special washe r p/n 13744B31 as follows:- 
(a) In accordance with the manufacturer’s instructi ons, apply Loctite 5203 liquid 
gasket to the inside faces of the special washer. 
(b) Clamp the special washer to the forward face of  the cylinder whilst the gasket 
cures. 
NOTE:  Liquid gasket cure time is 24 hours at 20 de g.C or 30 mins. if hot air not 
exceeding 120 deg.C is applied. It is acceptable to use Loctite 7240 Activator 
in accordance with the manufacturer’s instructions to further reduce curing 
time. 
(c) Remove all visible excess gasket material. The gasket should only be in the 
interface between the MLG and the special washer. 
(d) Refer to figure 2 detail E. Apply a small amoun t of suitable witness paint 
(such as F-900 Torque Seal or Loctite 7414) over the inboard edge of the 
special washer tab and onto the flat of the MLG spigot housing.

### Page 9

SERVICE BULLETIN  
ORIGINAL ISSUE: 8 th  April 2013  32-JM7862 
REVISION 3: 3 rd  October 2014  PAGE 7 
 
(e) Refer to figure 2 detail G. On DTD5094 cylinder s, apply a single coat of 
Tectyl 502-C corrosion prevention compound to the exposed surface on the 
forward spigot housing (i.e. the area treated with Alocrom that is not covered 
by the special washer). Do not apply within the inspection window on the 
special washer tab. 
On L161 cylinders, treat the exposed surface with epoxy primer and 
polyurethane paint topcoat in accordance with the aircraft SRM or MLG CMM. 
NOTE: The following Left Hand landing gear part num bers have cylinders made 
from DTD5094:- 
1863 (without strike off 3), 1863/4A, 1863/4B and 1863/4C (Pre Mod 86-
04-003 Re-issue 6), B00A702850A (without strike off 7 or 16), 
B00A702925A (without strike off 5 or 15). 
All other Left Hand landing gear part numbers (including all Jetstream 
Series 3200 gear types) have cylinders made from L161. 
(9) Reinstall the forward spigot in the MLG cylinde r subassembly as follows:- 
(a) Reinstall forward spigot in cylinder subassembl y. 
(b) Install spigot bolt, washer and slotted nut, wi th the slotted nut on the 
retraction side of the cylinder. 
(c) Tighten bolt with a maximum torque of 30 lbf.in . (3.4 Nm) using a suitable 
wrench. 
(d) Lock slotted nut with new split-pin p/n SP90C8.  
(e) Coat head and nut of spigot bolt with sealing c ompound to AMS-S-8802 or 
DTD 900/4502 (PR1422A2). 
(10) Refer to figure 1 and discard the forward spli t bearing p/n 13744B11 and replace 
with new bearing p/n 13744B29 as shown. 
(11) Check the two bearing locking pins P/N 13744B2 1 for signs of wear or damage to 
the heads. Worn/damaged heads can be repaired by grinding away the minimum 
amount of material required to achieve a flat surface. Refer to figure 2 detail F,  
ensure that the head of the pin is at least 0.05 in. (1.27 mm) long. If not, replace 
with a serviceable pin. Apply Alocrom (or Alodine) 1200 to the repaired surface. 
(12) Refer to AMM 32-10-11, page block 401 and rein stall the left MLG. 
NOTE: Trunnion/bearing cap to be installed with bea ring locking pins on the forward 
side.

### Page 10

SERVICE BULLETIN  
32-JM7862  ORIGINAL ISSUE: 8 th  April 2013 
PAGE 8  REVISION 3: 3 rd  October 2014 
 
Right MLG 
(1) Refer to AMM 32-10-11, page block 401 and remov e the right MLG.  
(2) Locate the forward spigot in the MLG cylinder s ubassembly and remove as 
follows:- 
(a) Remove and discard split-pin. 
(b) Remove slotted nut, spigot bolt and washer. 
(c) Withdraw forward spigot from cylinder. 
(3) Remove any paint or primer from the forward fac e of the MLG spigot housing in 
accordance with SRM 51-10-31. 
(4) Refer to SB 32-A-JA851226 and, if applicable, d o an NDT inspection of the MLG 
spigot (pintle) housing for cracks. 
(5) Check the condition of the forward face of the MLG spigot housing and, if 
necessary, restore protective treatment using Alocrom (or Alodine) 1200. Do not 
apply primer or paint. 
(6) Refer to figure 1 detail D. Position the specia l washer p/n 13744B31 over the 
spigot housing bore and mark the inside face of the washer to show the material 
to be removed to enable the washer to match the bottom of the bore. 
(7) Carefully trim material from the bottom inside diameter of the special washer  p/n 
13744B31 sufficient to create a gap of 0.002 to 0.005 in. (0.051 to 0.127 mm) 
between the special washer tab and the top flat surface of the MLG spigot 
housing when assembled with the forward spigot pin. Take care not to remove 
excessive material. If the gap is greater than 0.005 in. (0.127 mm), the special 
washer must be discarded. 
(8) Refer to figure 1 and install the special washe r p/n 13744B31 as follows:- 
(a) In accordance with the manufacturer’s instructi ons, apply Loctite 5203 liquid 
gasket to the inside faces of the special washer. 
(b) Clamp the special washer to the forward face of  the cylinder whilst the gasket 
cures. 
NOTE: Liquid gasket cure time is 24 hours at 20 deg .C or 30 mins. if hot air not 
exceeding 120 deg.C is applied. It is acceptable to use Loctite 7240 Activator 
in accordance with the manufacturer’s instructions to further reduce curing 
time. 
(c) Remove all visible excess gasket material. The gasket should only be in the 
interface between the MLG and the special washer. 
(d) Refer to figure 2 detail E. Apply a small amoun t of suitable witness paint 
(such as F-900 Torque Seal or Loctite 7414) over the inboard edge of the 
special washer tab and onto the flat of the MLG spigot housing.

### Page 11

SERVICE BULLETIN  
ORIGINAL ISSUE: 8 th  April 2013  32-JM7862 
REVISION 3: 3 rd  October 2014  PAGE 9 
 
 
(e) Refer to figure 2 detail G. On DTD5094 cylinder s, apply a single coat of 
Tectyl 502-C corrosion prevention compound to the exposed surface on the 
forward spigot housing (i.e. the area treated with Alocrom that is not covered 
by the special washer). Do not apply within the inspection window on the 
special washer tab. 
On L161 cylinders, treat the exposed surface with epoxy primer and 
polyurethane paint topcoat in accordance with the aircraft SRM or MLG CMM. 
NOTE: The following Right Hand landing gear part nu mbers have cylinders 
made from DTD5094:- 
1864 (without strike off 3), 1864/4A, 1864/4B and 1864/4C, (Pre Mod 86-
04-003 Re-issue 6), B00A702851A (without strike off 7 or 16), 
B00A702926A (without strike off 5 or 15). 
All other Right Hand landing gear part numbers (including all Jetstream 
Series 3200 gear types) have cylinders made from L161. 
(9) Reinstall the forward spigot in the MLG cylinde r subassembly as follows:- 
(a) Reinstall forward spigot in cylinder subassembl y. 
(b) Install spigot bolt, washer and slotted nut, wi th the slotted nut on the 
retraction side of the cylinder. 
(c) Tighten bolt with a maximum torque of 30 lbf.in . (3.4 Nm) using a suitable 
wrench. 
(d) Lock slotted nut with new split-pin p/n SP90C8.  
(e) Coat head and nut of spigot bolt with sealing c ompound to AMS-S-8802 or 
DTD 900/4502 (PR1422A2). 
(10) Refer to figure 1 and discard the forward spli t bearing p/n 13744B11 and replace 
with new bearing p/n 13744B29 as shown. 
(11) Check the two bearing locking pins P/N 13744B2 1 for signs of wear or damage to 
the heads. Worn/damaged heads can be repaired by grinding away the minimum 
amount of material required to achieve a flat surface. Refer to figure 2 detail F,  
ensure that the head of the pin is at least 0.05 in. (1.27 mm) long. If not, replace 
with a serviceable pin. Apply Alocrom (or Alodine) 1200 to the repaired surface. 
(12) Refer to AMM 32-10-11, page block 401 and rein stall the right MLG. 
NOTE: Trunnion/bearing cap to be installed with bea ring locking pins on the forward 
side.

### Page 12

SERVICE BULLETIN  
32-JM7862  ORIGINAL ISSUE: 8 th  April 2013 
PAGE 10  REVISION 3: 3 rd  October 2014 
 
 
C. Testing 
(1) Refer to AMM 32-30-00, page block 201 and do a functional test of the MLG. 
D. Recovery 
(1) Aircraft records:- 
(a) Add SB number “32-JM7862 Left” and/or “32-JM786 2 Right” to the aircraft 
records as appropriate. 
(b) When both the left and right MLGs have been mod ified, add modification 
number JM7862 to the aircraft records. 
(2) Inform BAE Systems of the accomplishment of thi s SB using the Accomplishment 
Report attached. 
NOTE: Operators are reminded of the necessity to inform:- 
Business Support Team, 
Technical Publications, 
BAE SYSTEMS (Operations) Limited, 
Prestwick International Airport, 
Ayrshire, 
KA9 2RW, 
SCOTLAND, 
of the accomplishment of this SB in order to obtain the necessary revisions for 
the affected manuals, see paragraph 1.L. Publications Affected, of this SB.

### Page 13 (OCR)

BRITISH  SPACE
JETSTREAM
SERIES 3100 & 3200
SERVICE BULLETIN
FWD
REAR SPAR
DATUM
0.002in TO 0.005in
(0.051mm TO 0.127mm)
GAP, FOR GASKET
SPECIAL
WASHER
13744B31
LEFT HAND SHOWN
RIGHT HAND OPPOSITE
SPIGOT
HOUSING  SPLIT
BEARING
(REF)  13744B29
0.002in TO 0.005in
(0.051mm TO 0.127mm)
GAP
FORWARD
REMOVE MATERIAL FROM BOTTOM  BEARING
SUFFICIENT TO CREATE A GAP  INSIDE DIAMETER OF WASHER  SECTION 'C-C'  JOURNAL  (REF)  SECTION 'C-C'
TO DIMENSIONS SHOWN BETWEEN  PRE MOD JM5218  POST MOD JM5218
WASHER TAB AND FLAT SURFACE OF  WASHER OMMITED FOR CLARITY  WASHER OMMITED FOR CLARITY
SPIGOT HOUSING.  J3210019
Installation of special washer and new bearing.
FIGURE 1
ORIGINAL ISSUE: 8th April 2013  32-JM7862
REVISION 3: 3rd October 2014  PAGE 11

### Page 14 (OCR)

BRITISH AEROSPACE
JETSTREAM
SERIES 2100 & 7200
SERVICE BULLETIN
CYLINDER (REF)
CENTRELINE
— INSPECTION
WINDOW
• OUTBOARD
SPECIAL WASHER
FWD
FORWARD SPIGOT
(REF)
G
VIEW LOOKING DOWN
ON MLG CYLINDER
LEFT SHOWN
RIGHT SIMILAR
MLG CYLINDER
SPECIAL WASHER
AREA TO BE PROTECTED
G
VIEW ON MLG CYLINDER SPIGOT
HOUSING FORWARD FACE AFTER
SPECIAL WASHER INSTALLATION
LOCKING PIN  BEARING  0.05in (1.27mm)  MINIMUM
_ GRIND AWAY
DAMAGE
J3210023
Witness paint application, spigot housing protection and bearing locking pin repair
FIGURE 2
32-JM7862  ORIGINAL ISSUE: 8th April 2013
PAGE 12  REVISION 3: 3r° October 2014

### Page 15

SERVICE BULLETIN  
ORIGINAL ISSUE: 8 th  April 2013  32-JM7862 
REVISION 3: 3 rd  October 2014  PAGE 13 
 
3. MATERIAL INFORMATION 
NOTE: The new part numbers shown in paragraph 3.A. are necessary to accomplish this SB  
on one aircraft.  Use the material kit number shown to order the parts. 
A. New parts supplied as a material kit - order kit  number JM7862. 
New Part No. QTY Keyword Old Part No. 
13744B31 2 Special washer - 
13744B29 2 Bearing 13744B11 
B. Materials required - Operators Supply 
Material No. QTY Keyword 
- A/R Alocrom (or Alodine) 1200 
- A/R Loctite 5203 liquid gasket 
SP90C8 2 Split-pin 
PR1422A2 A/R Sealing compound 
- A/R Tectyl 502-C 
- A/R Epoxy primer 
- A/R Polyurethane paint 
- A/R F-900 Torque Seal 
Alternative 
Loctite 7414 
13744B21 4 Bearing locking pin

### Page 16

SERVICE BULLETIN  
32-JM7862  ORIGINAL ISSUE: 8 th  April 2013 
PAGE 14  REVISION 3: 3 rd  October 2014 
 
 
BLANK PAGE

### Page 17

SERVICE BULLETIN  
ORIGINAL ISSUE: 8 th  April 2013  32-JM7862 
REVISION 3: 3 rd  October 2014  PAGE 15 
 
4. CONTINUED AIRWORTHINESS 
D. Continued Airworthiness Instructions 
The following information is provided to Operators to permit continued operation of the aircraft 
pending receipt of a formal revision to the relevant aircraft manuals. 
E. Scheduled Maintenance 
(1) Not applicable. 
F. Removal Procedures 
(1) Refer to part 2.B. of this SB. 
NOTE: Removal is the reverse of installation. 
G. Installation Procedures 
(1) Refer to part 2.B. of this SB. 
H. Test Procedures 
(1) Refer to part 2.C. of this SB. 
I. Trouble Shooting 
(1) Not applicable.

### Page 18

SERVICE BULLETIN  
32-JM7862  ORIGINAL ISSUE: 8 th  April 2013 
PAGE 16  REVISION 3: 3 rd  October 2014 
 
 
BLANK PAGE

### Page 19

abcd 
 
 
ACCOMPLISHMENT REPORT 
 
 
 
SERVICE BULLETIN NUMBER  32-JM7862 
 
TITLE: LANDING GEAR - INTRODUCTION OF SPECIAL WASHE R TO PROTECT THE MAIN 
LANDING GEAR CYLINDER AT THE FORWARD SPIGOT.  
 
TO: BUSINESS SUPPORT TEAM, 
 TECHNICAL PUBLICATIONS, 
 BAE SYSTEMS (OPERATIONS) LIMITED, 
 PRESTWICK INTERNATIONAL AIRPORT, 
 AYRSHIRE, KA9 2RW, 
 SCOTLAND. 
 
 Telephone: (01292) 675207 
 Fax:  (01292) 675704 
 E-mail: RAPublications@baesystems.com 
 
PLEASE BE ADVISED THAT THE ABOVE SERVICE BULLETIN HAS BEEN EMBODIED ON 
AIRCRAFT CONSTRUCTORS NUMBER(S): 
 
 
WE REQUEST THE APPROPRIATE REVISIONS TO APPLICABLE MANUALS. 
 
NAME:  ...........….................................................................... 
 
SIGNED:  ............................................................................... 
 
COMPANY:  ...............…........................................................ 
 
DATE:  ..................................................…............................. 
 
 
 
SERVICE BULLETIN COMMENTS/FEEDBACK. 
 
Please report any non-technical comments or inaccuracies regarding this service bulletin to the 
above address.

### Page 20

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
