# BAE Systems Inspection Service Bulletin J41-27-068: No revision named

- Rights: © BAE Systems. Filed by the FAA in regulations.gov docket FAA-2015-2957; AD 2015-15-09 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [BAE Systems Inspection Service Bulletin J41-27-068](https://openairdocs.org/service-documents/bae-systems/j41-27-068.md)
- Title as filed: SB J41-27-068R00
- Pages: 15
- PDF: https://openairdocs.org/files/sha256/6f/9c/6f9c9fdf3c654bb783985b85b20a3bc9153e367a8dd6e25c74ad340589d03b69
- Page: https://openairdocs.org/service-documents/bae-systems/j41-27-068/file/6f9c9fdf3c65

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

BAe JETSTREAM
Series 4100
SERVICE BULLETIN
BRE STICK INTERNATIONAL AIM PORT,
AYRSHIRE, KA9 2RW,
SCOTLAND.
J41-27-068
TRANSMITTAL SHEET
This page transmits the original issue of service bulletin J41-27-068, pages 1 through 12.
ITLE: FLIGHT CONTROLS - INSPECTION OF ELEVATOR TRIM CIRCUIT TRAVEL STOPS
AND SERVO MOTOR LIMIT MICRO SWITCH RIGGING
INSPECTION
ORIGINAL ISSUE: JAN 21/14  141-27-06
AGE 10t

### Page 2

(No text on this page.)

### Page 3 (OCR)

BAe JETSTREAM
Series 4100
SERVICE BULLETIN
BAE SYSTEMS (OPERATIONS) LIMITED,
PRESTWICK INTERNATIONAL AIRPORT,
AYRSHIRE, KA9 2RW,
SCOTLAND.
J41-27-068
TITLE: FLIGHT CONTROLS - INSPECTION OF ELEVATOR TRIM CIRCUIT TRAVEL STOPS
AND SERVO MOTOR LIMIT MICRO SWITCH RIGGING
INSPECTION
1.  PLANNING INFORMATION
A.  Effectivity
All Jetstream Series 4100 aircraft.
B.  Reason
An incident occurred where the aircraft pitched down during the final approach phase
with the landing gear lowered and the autopilot disconnected. Despite the control
column being held fully aft, the aircraft continued to lose height, and the crew then
found that the pitch trim circuit was fully nose down. It took considerable effort to free
the circuit from that position, but control was then regained.
Subsequent investigation showed that the pitch trim cable travel stop plates in the
centre console had failed, allowing the swaged stop to over travel past the plates. When
the crew tried to trim the aircraft nose up, the stop then snagged on the edge of the stop
plate.
C.  Description
A one off inspection is required to ensure that, when the pitch trim servo is operated to
the limits of its travel, both pitch up and down, the cable travel stops do not contact the
stop plates. The stop plates are also inspected to ensure that they have not been
damaged.
The tasks are as follows:
- Gain access to rear of centre console.
- Operate electrical pitch trim switches fully up and fully down.
- Check that the travel stops do not contact the travel stop plates.
- Check and rectify the rigging if defective.
- Inspect the travel stop plates, replace if necessary.
- The aircraft records are amended.
ORIGINAL ISSUE: JAN 21/14  J41-27-068
PAGE 1 of 12

### Page 4 (OCR)

BAe JETSTREAM
Series 4100
SERVICE BULLETIN
D. Manpower
1 man-hour.
Mechanical and electrical skills are necessary.
E.  Material - Cost and Availability
The Modifications Group, BAE Systems (Operations) Limited, Prestwick International
Airport, Ayrshire, KA9 2RW, SCOTLAND, will give you terms and conditions for the
supply of material.
Tooling - Price and Availability
None.
G. Weight and Balance
None.
Aircraft Noise Levels
Not affected.
Electrical Load Data
Not affected.
Software Accomplishment Summary
Not applicable.
K. References
- Aircraft Maintenance Manual, Chapters 12-21-24, 22-10-18 and 27-35-00.
Publications Affected
None.
M. Family Tree Of Modification Relationships
Not applicable.
J41-27-068  ORIGINAL ISSUE: JAN 21/14
PAGE 2

### Page 5 (OCR)

AE JETSTREAN
eries 410
SERVICE BULLETIN
N. Approval
The technical content of this service bulletin is the subject of EASA Airworthiness
Directive consultation.
Compliance with this service bulletin must be achieved as follows:
By the 30h April 2014.
The technical content of this service bulletin is approved under the authority of EASA
PART 21 Approval No. EASA.21J.047.
Signed
Date
EASA Part 21 Approval No. EASA.21J.047.
ORIGINAL ISSUE: JAN 21/14  J41-27-068
PAGE 3

### Page 6 (OCR)

Ae JETSTREAL
eries 410
SERVICE BULLETIN
BLANK PAGE
PAGE 068  ORIGINAL ISSUE: JAN 21/14

### Page 7 (OCR)

BAe JETSTREAM
Series 4100
SERVICE BULLETIN
2.  ACCOMPLISHMENT INSTRUCTIONS
WHENEVER ANY PART OF THE MAIN OR ASSOCIATED SYSTEM IS DISMANTLED,
ADJUSTED, REPAIRED OR RENEWED, THAT PART OF THE SYSTEM WHICH HAS
BEEN DISTURBED SHALL BE SUBJECTED TO A SECOND INDEPENDENT INSPECTION
FOR SECURITY OF LOCKING DEVICES, FULL AND FREE MOVEMENT, DIRECTION AND
TENSION CHECKS. THIS WORK MUST BE DONE IN ACCORDANCE WITH THE
ACCEPTABLE MEANS OF COMPLIANCE M.A. 402 (a) TO EASA PART M, OR TO AN
EQUIVALENT NATIONAL STANDARD.
WARNING: MAKE SURE THE AIRCRAFT AND THE AIRCRAFT SYSTEMS ARE MADE
SAFE AS DETAILED IN THE APPLICABLE CHAPTERS OF THE AIRCRAFT
MAINTENANCE MANUAL.
CAUTION:  TO AVOID DAMAGE, MAKE SURE BEFORE MOVING CONTROLS THAT
CONTROL RUNS AND CONTROL SURFACES ARE FREE FROM
OBSTRUCTION.
NOTE: Abbreviations used in the accomplishment instructions of this service bulletin
are:
AMM - Aircraft Maintenance Manual.
A.  Preparation
(1) Refer to AMM, chapter 27-35-00. Gain access to rear of centre console and
remove access panels 230BRW, 230BLW, 230CRW and 230CLW.
B.  Accomplishment
(1)  Connect the external electrical power to the aircraft, refer to AMM, chapter
12-21-24 (Ref. AMM 12-21-24-860-801).
Refer to AMM, chapter 27-35-00. Operate electrical pitch trim switches fully
up and fully down. Make sure that the travel stops do not contact the travel
stop plates.
(3)  Check rigging. If the rigging is found to be defective refer to AMM, chapter
22-10-18 to rectify.
(4)  Correctly adjust the electric trim limit switches (Ref. AMM 22-10-18-820-
806).
Refer to Figure 1. Inspect the travel stop plates part number 14127025-51 (1
to 3 off per aircraft). Check for damage or broken stop arms. Replace
damaged stop plates if necessary.
NOTE: There are two different standards of stop plates. Both have the same part
number. Early production stop plates have shorter stop arms. It is recommended
that any early type stop plates are replaced with later production stop plates.
The stop plates are made of tufnol.
ORIGINAL ISSUE: JAN 21/14  J41-27-068
PAGE 5

### Page 8 (OCR)

BAe JETSTREAM
Series 4100
SERVICE BULLETIN
C. Recovery
(1)  Refer to AMM, chapter 27-35-00, gain access to the rear of the centre
console and install access panels 230BRW, 230BLW, 230CRW and
230CLW.
(2)  Disconnect external electrical power to the aircraft, refer to AMM, chapter
12-21-24 (Ref. AMM 12-21-24-860-805).
(3) Aircraft records:
(a) Add inspection service bulletin number J41-27-068 to the aircraft
records.
NOTE: Operators are reminded of the necessity to inform the Business Support Team,
Technical Publications, BAE Systems (Operations) Limited, Prestwick International
Airport, Ayrshire, KA9 2RW, SCOTLAND, of the accomplishment of this service
bulletin in order to obtain the necessary revisions for the affected manuals, see
paragraph 1.L. Publications Affected, of this service bulletin.
NOTE: Operators are also reminded that it is their responsibility to amend the aircraft
weighing report, if necessary, in accordance with the weight and balance changes
given at paragraph 1.G. of this service bulletin.
J41-27-068  ORIGINAL ISSUE: JAN 21/14
PAGE 6

### Page 9 (OCR)

BAe JETSTREAM
Series 4100
SERVICE BULLETIN
CABLE STOP
BRACKET
(REF)
SHORT  LONG
STOP ARM  STOP ARM
0.13in (3.302mm)
TYPICAL
0.225in
(5.715mm)
TYPICAL  EARLY PRODUCTION  LATER PRODUCTION
STOP PLATE  STOP PLATE
14127025-51  14127025-51
27-35-10019
ORIGINAL ISSUE: JAN 21/14  J41-27-068
PAGE 7

### Page 10 (OCR)

BAo JET Series 4100
SERVICE BULLETIN
BLANK PAGE
J41-27-068  ORIGINAL ISSUE: JAN 21/14
PAGE 8

### Page 11 (OCR)

BAe JETSTREAM
Series 4100
SERVICE BULLETIN
MATERIAL INFORMATION
A.  New parts supplied
Not applicable.
B.  Replacement Parts - Operators Supply
Not applicable.
C. Instruction Dispositions Notes
Not applicable.
ORIGINAL ISSUE: JAN 21/14  J41-27-068
PAGE 9

### Page 12 (OCR)

BAO JETSTRE4100
SERVICE BULLETIN
BLANK PAGE
PAGE 1068  ORIGINAL ISSUE: JAN 21/14

### Page 13 (OCR)

BAe JETSTREAM
Series 4100
SERVICE BULLETIN
4.  CONTINUED AIRWORTHINESS
A. Continued Airworthiness Instructions
There are no continued airworthiness instructions applicable to this service bulletin.
B. Scheduled Maintenance
(1) Not applicable.
C. Removal Procedures
(1) Not applicable.
D.  Installation Procedures
(1) Not applicable.
E. Test Procedures
(1) Not applicable.
F. Trouble Shooting
(1) Not applicable.
ORIGINAL ISSUE: JAN 21/14  J41-27-068
PAGE 11

### Page 14 (OCR)

BAe JETSTREAM
Series 4100
SERVICE BULLETIN
BLANK PAGE
J41-27-068  ORIGINAL ISSUE: JAN 21/14
PAGE 12

### Page 15 (OCR)

BAE SYSTEMS
ACCOMPLISHMENT REPORT
SERVICE BULLETIN NUMBER  J41-27-068
TO:  BUSINESS SUPPORT TEAM,
TECHNICAL PUBLICATIONS,
BAE SYSTEMS (OPERATIONS) LIMITED,
PRESTWICK INTERNATIONAL AIRPORT,
AYRSHIRE, KA9 2RW,
SCOTLAND.
Telephone: (01292) 675207
Fax:  (01292) 675704
E-mail:  RAPublications@baesystems.com
PLEASE BE ADVISED THAT THE ABOVE SERVICE BULLETIN HAS BEEN EMBODIED ON
AIRCRAFT CONSTRUCTORS NUMBER(S):
WE REQUEST THE APPROPRIATE REVISIONS TO APPLICABLE MANUALS.
NAME:
SIGNED:
COMPANY:
DATE:
SERVICE BULLETIN COMMENTS/FEEDBACK
Please report any non-technical comments or inaccuracies regarding this service bulletin to the
above address.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
