# Hawker Beechcraft Mandatory Service Bulletin 57-4112: No revision named

- Rights: © Textron Aviation Inc. Filed by the FAA in regulations.gov docket FAA-2014-0254; AD 2014-15-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Hawker Beechcraft Mandatory Service Bulletin 57-4112](https://openairdocs.org/service-documents/beechcraft/sb-57-4112.md)
- Title as filed: FAA-2014-0254_SB 57-4112
- Pages: 13
- PDF: https://openairdocs.org/files/sha256/7a/b5/7ab5c5a18eb6d9c50322080802a2b2c879ff932e583e8df90f44fcffa9dfc80c
- Page: https://openairdocs.org/service-documents/beechcraft/sb-57-4112/file/7ab5c5a18eb6

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

Herker Beechcraft
MANDATORY
SERVICE BULLETIN
TITLE: WINGS - SEALING OF FUEL VENT SURGE TANK FOR LIGHTNING PROTECTION IN WINGLET  INSTALLATION
1. Planning Information
A. Effectivity
(1) Airplanes
Hawker 800XP and Hawker 850XP, if equipped with one of the following kits: 140-1701-1,
140-1702-1, 140-1703-1, 140-1703-5, 140-1703-7 or 140-1704-1.
NOTE
The above-listed kits meet the intent of this Service Bulletin if purchased from
Hawker Beechcraft Corporation (HBC) after the release date of this Service
Bulletin. No further action is required
Hawker 900XP, Serials HA-0156 and HA-0159.
If you are no longer in possession of the airplane, please forward this information to the present
owner.
(2) Spares
None.
B. Reason
This Service Bulletin is being issued because the winglet installation may have omitted sealant in the left
and right fuel vent surge tank between ribs 14 and 15. Sealant is required for lightning protection.
C. Description
This Service Bulletin is being issued to inspect for sealant in the left and right fuel vent surge tank between
ribs 14 and 15. If the required sealant is missing, it shall be applied to the affected areas.
Tomstation Regulars Owersion coitary to 05 law is prombed for gu cance oft  Administration Regulations. Diversion contrary to U.S  For guidance on
export control requirements.  contact the Commerce Department's Bureau
Administration at http /www.bis.doc.gov
Hawker Beecheraft Corporation (HBO) Issues Service Information for the benefit of owners
Mandatory Service Bulletins (red border) includes changes, inspection and modifications that  and fixed base operators in the form of two classes of Service Bulletins.  The first class
could affect safety or crashworthiness HBC also issues Service Bulletins with no red border
which are designated as either recommended or optional in the compliance section within the
bulletin  In the case of recommended Service Bulletins, HBC feels the changes.
modifications, improvements or inspections will benefit the owner/operator and although
highly recommended. Recommended Service Bulletins are not considered mandatory at the
time of issuance  In the case of Optional Service Builetins, complance with the changes
modifications improvements or inspections is at the owner/operator's discretion
Both classes are available on the web at htto //pubs hawkerbeechcraft com and mailed to
Owners of record on the FAA Aircraft Registration Branch List and the H8O  Safety of Flight Inforation (SOFI) List
(b) Those having a publications supscription
the Hawker Beechcraft Corporation Technical Manual Distrbution Center (TMDC)  Information on Safely of Flight Information SOFI) or subsorbonen Center TO C An
Mandatory Service Bulletins and Service Bulletins are issued, the Service Bulletin Master
Index will be updated and available online at http i/pubs nawkerbeechcraft com  will be allowed only when specially cefined in the Service Bulletin and in accordance with
HBC Warranty Policy
Unless otherwise designated, HBC Mandatory Service Builetins, Service Bulletins and HBC
Kits are approved for installation on HBC airplanes in onginal or HBC modified configurations
enly. HBC Mandatory Service Bulletins Service Bulletins and Kits may not be compatible
with airplanes modified by STC installations or modifications other than HBC approved kits
Member of GAMA
Issued: February, 2013  SB 57-4112
1 of 13

### Page 2 (OCR)

Hawker Beechcraft
MANDATORY
SERVICE BULLETIN
D. Compliance
An Airworthiness Directive will be requested on the matter covered by this Service Bulletin.
Hawker Beechcraft Corporation considers this to be a Mandatory Service Bulletin. It must be accomplished
no later than 600 flight hours or 12 months from issuance of this Service Bulletin, whichever occurs first.
E. Approval
The engineering data contained in this Service Bulletin is FAA approved.
Prior to accomplishment, owners/operators of airplanes registered in countries other than the United
States shall consult with their local Aviation Regulatory Authority.
Incorporation of this Service Bulletin restores the airplane to original Type Design.
F. Manpower
The following information is for planning purposes only:
Estimated man-hours for Part A: 2 hours
Estimated man-hours for Part B: 36 hours
Suggested number of technicians: 1
The above is an estimate based on experienced, properly equipped technicians complying with this
Service Bulletin.
G. Weight and Balance
Negligible.
It is the responsibility of the owner/operator to maintain compliance with the applicable Airworthiness
Regulations.
H. Electrical Load Data
No change.
I. Software Accomplishment Summary
Not applicable.
J. References
Kit 140-1701-1;
Kit 140-1702-1;
Kit 140-1703-1;
Kit 140-1703-5;
Kit 140-1703-7;
Kit 140-1704-1.
Aircraft Maintenance Manual (AMM), Chapter 12, Chapter 20, and Chapter 28.
Issued: February, 2013  SB 57-4112
2 of 13

### Page 3 (OCR)

Hawker Beechcraft
MANDATORY
SERVICE BULLETIN
K. Publications Affected
None.
L. Interchangeability of Parts
Not applicable.
M. Warranty Credit
Warranty credit for labor and parts to the extent noted under MANPOWER and MATERIAL will be allowed
on all airplanes meeting all the following criteria:
(1) Airplane owners must have active Standard Warranty coverage and/or an active HBC Maintenance
program with applicable Service Bulletin coverage for the subject airplane when the Service Bulletin
is Issued.
(2) Standard Warranty coverage and/or HBC Maintenance Program with applicable Service Bulletin
coverage must be active for the subject airplane on the day the work is accomplished.
(3) The work shall be accomplished in accordance with the criteria defined in Paragraph 1.D.,
COMPLIANCE.
(4) The work shall be accomplished in accordance with criteria defined in Paragraph 3,
ACCOMPLISHMENT INSTRUCTIONS.
(5) The work shall be accomplished at an HBC ASC facility Hawker rated to perform maintenance on
the specific model of Hawker Beechcraft airplane.
(6) While work shall be accomplished in accordance with the criteria defined in Paragraph 1.D,
COMPLIANCE, warranty coverage offered in this Service Bulletin will expire 12 months from the last
day of the month this Service Bulletin is issued.
(7) Claims for compliance with this Service Bulletin (SB) are to be filed as a W3-type claim against SB
57-4112.
(8) After the Service Bulletin has been accomplished, a warranty claim must be submitted to HBC within
60 days of the Service Bulletin completion date.
(9) HBC will not provide compensation for fuel removed to perform the accomplishment instructions of
this Service Bulletin.
2. Material Information
A. Materials - Price and Availability
Contact information:
Hawker Beechcraft Parts & Distribution (HBP&D)
10511 East Central Avenue
Wichita, KS 67206
USA
Phone: 316-676-3100 or 1-888-727-4344
Fax: 316-676-3222 or 316-676-3327
E-mail: HBC_Parts@hawkerbeechcraft.com
Issued: February, 2013  SB 57-4112
3 of 13

### Page 4 (OCR)

Hawker Beechcraft
MANDATORY
SERVICE BULLETIN
B. Industry Support
Not applicable.
C. Airplanes
(1) The following parts required for accomplishment of this Service Bulletin may be ordered through a
Hawker Beechcraft Authorized Service Center or HBP&D:
Part Number  Description  Quantity Per Airplane
100-214-8815  O-Ring (Preformed Packing)  2
AGS 1186-3  Seal  8
100-230-8815  O-Ring (Preformed Packing)  4
100-226-8815  O-Ring (Preformed Packing)  2
Hawker Beechcraft Corporation expressly reserves the right to supersede, cancel and/or declare
obsolete, without prior notice, any parts or publications that may be referenced in this Service
Bulletin.
(2) The following materials may be obtained locally:
Material Item / Part Number  Description  Quantity Per
Airplane
20-95-301-001, Item 335A  Adhesion Promoter  As Required
(Ref. AMM Chapter 20)
20-95-201-001, Item 201  Aliphatic Naphtha  As Required
(Ref. AMM Chapter 20)
20-95-301-001, Item 351  Sealant  As Required
(Ref. AMM Chapter 20)
A-A-1491, CCC-C-440, Or  Cotton Cheesecloth  As Required
Equivalent
A-A-53513 or 1877711  Gloves, Polyethylene, Industrial Air Solvent Handling  As Required
D. Spares
Not applicable.
E. Reidentified Parts
None.
Issued: February, 2013  SB 57-4112
4 of 13

### Page 5 (OCR)

Hawker Beechcraft
MANDATORY
SERVICE BULLETIN
F. Tooling - Price and Availability
Not applicable.
3. Accomplishment Instructions
This Service Bulletin shall be accomplished as follows:
NOTE
Should any difficulty be encountered in accomplishing this Service Bulletin,
contact Hawker Beechcraft Corporation at 1-800-429-5372 or 316-676-3140.
WARNING
Observe all Warnings and Cautions contained in the airplane manuals
referenced in this Service Bulletin.
Whenever any part of this system is dismantled, adjusted, repaired or
renewed, detailed investigation must be made on completion to make sure
that distortion, tools, rags or any other loose articles or foreign matter that
could impede the free movement and safe operation of the system are not
present, and that the systems and installations in the work area are clean.
A. Airplane
(1) Remove all power from the airplane and disconnect the batteries. Display warning notices
prohibiting reconnection of airplane electrical power.
NOTE
The following instructions apply to the left and right fuel vent surge tanks.
Part A: Inspection of Left and Right Fuel Vent Surge Tanks for Sealant
(1) Defuel the aircraft and purge the fuel cell in accordance with Aircraft Maintenance Manual (AMM),
Chapter 12-28-00 and Chapter 28-10-15.
(2) Remove wing fuel surge tank access panel, P/N 25-8WS903-11-2, as follows:
(a) Remove 27 bolts, P/N 25-WS3195-5, in accordance with guidelines provided in Structural
Repair Manual (SRM), Chapter 51-43-00-001. Each bolt may be used again if the finish is
undamaged and the thread is in good condition. Refer to Figure 2 and Figure 3.
(b) Remove wing fuel surge tank access panel, P/N 25-8WS903-1/-2.
(3) Remove wing access panel, P/N 25-8WS905-1A, as follows:
(a) Remove 10 bolts, P/N 25-WS3195-1, in accordance with guidelines provided in SRM, Chapter
51-43-00-001. Each bolt may be used again if the finish is undamaged and the thread is in good
condition. Refer to Figure 2 and Figure 3.
(b) Remove wing access panel, P/N 25-8WS905-1A.
Issued: February, 2013  SB 57-4112
5 of 13

### Page 6 (OCR)

Hawker Beechcraft
MANDATORY
SERVICE BULLETIN
(4) Inspect to determine if sealant exists on doubler plate edges, doubler plate rivets, and adjacent skin
in the top and bottom of the fuel surge tank. Refer to Figures 1 through 4.
(a) If sealant exists, no further action is required. Proceed to Final Check.
(b) If sealant does not exist, proceed to Part B.
Part B: Application of Sealant in the Left and Right Fuel Vent Surge Tanks
(1) Determine if duct, P/N 25-8PV219-1A, and intake assembly, P/N 25-8PV217-1A/2A, need to be
removed to make it possible to remove duct assembly, P/N 25-8PV223-1A/2A. Refer to Figure 1.
(a) If the duct assembly, P/N 25-8PV223-1A/2A, can be removed with the associated parts in place,
proceed to Step (2).
(b) If the duct assembly, P/N 25-8PV223-1A/2A, can not be removed with the associated parts in
place, proceed to Step (1)(c).
(c) Inboard of rib 14, remove intake assembly, P/N 25-8PV217-1A/2A. Remove duct,
P/N 25-8PV219-1A. Discard seals. Proceed to Step (2).
(2) Accomplish the following in the wing surge tank between ribs 14 and 15:
(a) Locate float switch, P/N 3515000-106, that is attached to rib 15.
(b) Outboard of rib 15, disconnect wiring that corresponds to overfill float switch, P/N 3515000-106,
and high-level float switch, P/N 3515000-107. The high-level float switch is attached to rib 14.
Remove the overfill float switch, P/N 3515000-106. Do not remove the high-level float switch.
Discard seals. Use applicable guidelines in AMM, Chapter 28-44-43-401.
(c) Wiring runs from the high-level float switch, P/N 3515000-107, to conduit assembly,
P/N 25-8PV201-15A/16A. A bond jumper connects conduit assembly, P/N 25-8PV223-1A/2A.
Disconnect the bond jumper at both ends. Retain the bond jumper.
(d) Remove conduit assembly, P/N 25-8PV201-15A/16A.
(e) The wiring shall be coiled and temporarily attached outside of the wing through the access panel
between ribs 14 and 15.
NOTE
It is advised to use the access area inboard of rib 14 to assist in removal of duct
assembly, P/N 25-8PV223-1A/2A.
(f) Remove duct assembly, P/N 25-8PV223-1A/2A.
(g) Protect any open holes from sealant that will be added in the following steps.
WARNING
Solvents and sealants are flammable and toxic to skin, eyes, and respiratory
tract. Skin and eye protection is required. Avoid repeated or prolonged
contact. Keep away from flames or sources of heat. Use in a well-ventilated
area or respiratory protection equipment may be required.
Issued: February, 2013  SB 57-4112
6 of 13

### Page 7 (OCR)

Hawker Beechcraft
MANDATORY
SERVICE BULLETIN
(3) Three doubler plates require sealant protection on the fuel surge tank upper skin:
Doubler plate, P/N 25-8WS6047;
Doubler plate, P/N 25-8WS6049;
Doubler plate, P/N 25-8WS6057.
One doubler plate requires sealant protection on the fuel surge tank lower skin:
Doubler plate, P/N 25-8WS6061.
The doubler plate edges and rivets, along with adjacent skin, shall be covered with sealant as
defined in the following Step (4), along with Figures 2, 3 and 4.
Clean these areas as follows:
(a) Dispense Aliphatic Naphtha onto cheese cloth in accordance with AMM Chapter 20-95-201-001,
Item 201. Do not wipe the cloth into the solvent.
(b) Use the cloth to clean the surface. Turn the cloth frequently. Change to a new cloth as soil
becomes evident.
(c) Before the Naphtha evaporates, dry the surface using a clean, lint-free cloth. Repeat Steps
(3)(a) through (3)(c) until the drying cloth shows no sign of soil removal.
(d) Clean the surface again, in accordance with the above procedure, if the surface is not sealed
within 24 hours.
(e) Apply a thin coat of adhesion promoter, P/N PR-148, by brush or clean gauze pad. Wipe off
excess with clean gauze pad. Dry time ranges from 15 minutes at 70° Fahrenheit to 45 minutes
at 40° to 60° Fahrenheit ambient conditions. If sealing is not completed within 8 hours, repeat
the process.
(4) Accomplish the following on the upper and lower skin of the wing surge tank, between ribs 14 and
NOTE
Prior to application of sealant in the steps below, it is permissible to verify the
process by conducting a practice application on scrap material.
Additional sealant may be applied, if necessary.
Due to limited access in this area, visual inspection will be required to verify
minimum sealant thickness.
It is permissible to use a long nozzle extruder, brush, non-metallic spatula or clean
gauze pad
Use the sealant manufacturer's technical data sheet for application times, tack
tree times, and cure times.
Issued: February, 2013  SB 57-4112
7 of 13

### Page 8 (OCR)

Hawker Beechcraft
MANDATORY
SERVICE BULLETIN
For every 10° above 77° Fahrenheit, the sealant application time is reduced by
half, and for every 10° below 77° Fahrenheit, the application time is doubled.
Sealant can be exposed to fuel after 48 hours.
(a) Apply sealant, P/N PR-1440, to all fasteners that are installed on upper skin doubler plates,
P/N 25-8WS6047, P/N 25-8WS6049, and P/N 25-8WS6057. In addition, apply the same sealant
to the lower skin doubler plate, P/N 25-8WS6061.
(b) Establish a minimum of 0.12-inch sealant coverage over each fastener.
(c) Apply sealant, P/N PR-1440, to all exposed edges of the four doubler plates.
(d) Establish a minimum of 0.15-inch sealant coverage over all exposed edges of the doubler
plates.
(e) Establish a minimum of 0.25-inch sealant coverage extending from the doubler plate edges to
the skin.
(5) Remove any protective covers that were installed over open holes in Step (2)(g).
(6) Install duct assembly, P/N 25-8PV223-1A/2A, using new seal, P/N 100-230-8815. Establish
clearance of 0.12/0.35-inch between the tube end fitting extending out from the fitting in the rib.
Refer to Figure 1.
(7) Use applicable new seals, P/N 100-226-8815, and P/N 100-230-8815, to install duct,
P/N 25-8PV219-1A, and intake assembly, P/N 25-8PV217-1A/2A, if these items were removed in
Part B, Step (1). Establish clearance of 0.29/0.63-inch between duct and intake assembly. Refer to
Figure 1. If these items were not removed in Part B, Step (1), proceed to the following Step (8).
(8) Accomplish the following to move float switches into position:
(a) Use the coiled wiring that was disconnected from the high-level float switch, P/N 3515000-107,
to install the conduit assembly, P/N 25-8PV201-15A/16A.
(b) Install overfill float switch, P/N 3515000-106, to rib 15 with four (4) new seals, P/N AGS1186-3
and seal, P/N 100-214-8815. Use applicable guidance in AMM, Chapter 28-44-43-401.
(c) Outboard of rib 15, reconnect wiring for overfill float switch, P/N 3515000-106, and high-level
float switch, P/N 3515000-107. Use applicable guidance in AMM, Chapter 28-44-43-401, and
Chapter 28-22-143-401.
(d) Connect the bond jumper between the conduit assembly and duct assembly,
P/N 25-8PV223-1A/-2A.
Final Check
(9) Install access panels that were removed in Step (2) and Step (3) of Part A. Use the retained
hardware.
(10) Fuel the aircraft in accordance with AMM Chapter 12-28-00.
(11) Reconnect the airplane batteries, remove warning notices, and restore power.
Issued: February, 2013  SB 57-4112
8 of 13

### Page 9 (OCR)

Hawker Beechcraft
MANDATORY
SERVICE BULLETIN
(12) Ensure all work areas are clean and clear of tools and miscellaneous items of equipment.
(13) _ Return airplane to service.
B. Spares
Not applicable.
C. Record of Compliance
Upon completion of this Service Bulletin, make an appropriate maintenance record entry.
Issued: February, 2013  SB 57-4112
9 of 13

### Page 10 (OCR)

Hawker Beechcraft
MANDATORY
SERVICE BULLETIN
RIB 14
DETAIL A  RIB 15
IF NECESSARY,
REMOVE INTAKE ASSEMBLY,
P/N 25-8PV217-1A  NOTE A -
P/N 25-8PV217-2A
RIB 14
IF NECESSARY, REMOVE
VENT DUCT, P/N 25-8PV219-1A.
- NOTE B
RIB 15  REMOVE DUCT ASSEMBLY,  P/N 25-8PV223-1A/-2A.
LOCATION FOR HIGH-LEVEL FLOAT SWITCH,
P/N 3515000-107 AND CONDUIT
ASSEMBLY, P/N 25-8PV201-15A/-16A.
REMOVE OVER-FILL
FLOAT SWITCH,
DETAIL B  P/N 3515000-106.
NOTES:
A = 0.29/0.63-INCH CLEARANCE BETWEEN DUCT AND INTAKE ASSEMBLY FOR INSTALLATION PURPOSES IN PART B, STEP (7).
B = 0.12/0.35-INCH CLEARANCE BETWEEN THE TUBE END FITTING EXTENDING OUT FROM THE FITTING IN THE RIB,  FOR INSTALLATION PURPOSES IN PART B, STEP (6).
B411203.AI
Duct Configuration for Fuel Vent Surge Tank
Figure 1
Issued: February, 2013  SB 57-4112
10 of 13

### Page 11 (OCR)

Hawker Beechcraft
MANDATORY
SERVICE BULLETIN
DETAIL A  ESTABLISH A MINIMUM OF
VIEW LOOKING UP
0.12 INCH SEALANT COVER
APPLY SEALANT TO  RIB 15  ON EACH RIVET. (TYPICAL)
THE DOUBLER
PLATE EDGE, ALL
THE WAY AROUND
RIB 14
PLATE P/N
25-8WS6047
a7 277
PLATE P/N  etr
25-8WS6049
1 27
Vete
+ era
PLATE P/N
25-8WS6057
TOP SKIN SHOWN
VIEW LOOKING UP
DETAIL BE  B411202 AI
Sealant Coverage for Upper Skin
Figure 2
Issued: February, 2013  SB 57-4112
11 of 13

### Page 12 (OCR)

Hawker Beechcraft
MANDATORY
SERVICE BULLETIN
REMOVE ACCESS PANEL.
P/N 25-3WS903-1/2.
RETAIN ATTACHMENT HARDWARE.
REMOVE ACCESS PANEL,
P/N 25-8WS905-1A.
RETAIN ATTACHMENT HARDWARE.  RIB 15  RIB 14
ESTABLISH A MINIMUM OF
0.12 INCH SEALANT COVER
ON EACH RIVET. (TYPICAL)
PLATE P/N
-25-8WS6061
APPLY SEALANT TO
VIEW LOOKING DOWN  BOTTOM SKIN SHOWN  THE DOUBLER
DETAIL A E  THE WAY AROUND  PLATE EDGE, ALL
B411201 AI
Sealant Coverage for Lower Skin
Figure 3
Issued: February, 2013  SB 57-4112
12 of 13

### Page 13 (OCR)

Hawker Beechcraft
MANDATORY
SERVICE BULLETIN
B→  A = 0.15 MIN  B = 0.15 MIN
C = 0.25 MIN
D411204 A1
Sealant Dimension Requirements
Figure 4
Issued: February, 2013  SB 57-4112
13 of 13

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
