# Bell Alert Service Bulletin 204B-12-68: No revision named

- Rights: © Bell Textron Inc. Filed by the FAA in regulations.gov docket FAA-2013-0735; AD 2014-03-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Bell Alert Service Bulletin 204B-12-68](https://openairdocs.org/service-documents/bell/204b-12-68.md)
- Title as filed: U.S. DOT/FAA - Bell ASB No 204B-12-68
- Pages: 6
- PDF: https://openairdocs.org/files/sha256/33/45/33458d79eaccf0553469fdcc4c11eed51c6226da6dde557910bb017ee7c19d02
- Page: https://openairdocs.org/service-documents/bell/204b-12-68/file/33458d79eacc

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ASB 204B-12-68 
Page 1 of 6 
ECCN EAR99 
 
 
 
 
 
  ALERT SERVICE BULLETIN 204B-12-68 
10 October 2012 
 
 
MODEL AFFECTED:  204B 
 
SUBJECT: P/N 205-001-720-001 CABLE ASSEMBLY, ONE 
TIME INSPECTION FOR DEFECTIVE BODY, P/N 
205-001-742-001 
 
HELICOPTERS AFFECTED: ALL 204B HELICOPTERS 
 
  
COMPLIANCE: PART I (Inspection): Within the next 25 flight hours 
 
 PART II (Replacement):  Within the next 100 flight 
hours after receipt of this ASB, but no later than 
                                                     31 January 2013 
 
DESCRIPTION: 
 
A number of P/N 205-001-720-001 cable a ssemblies have been manufactured with 
defective P/N 205-001-742-001  bodies. The bodies are mismachined such that the 
P/N 0301245 barrel assembly will not fully engage in the body cavity. This ASB is a 
one-time inspection of all P/N 205-001-720-001 cable assemb lies for the defective 
condition. Defective cable assemblies must  be replaced as noted in the Compliance 
Section of this ASB.  Applicability of this  bulletin to any spare part shall be determined 
prior to its installation on an affected helicopter. 
 
APPROVAL: 
 
The engineering design aspects of this bulletin are FAA/ODA approved. 
 
CONTACT INFO: 
 
For any questions regarding this bulletin, please contact: 
 
Bell Helicopter Product Support Engineering - Medium Military Helicopters 
Tel: 817-280-3548 / mts-medium@bh.com

### Page 2

ASB 204B-12-68 
Page 2 of 6 
ECCN EAR99 
 
MANPOWER: 
 
Approximately 1 man-hour is required to complete PART I of this bulletin.  
Approximately 8 man-hours are required to complete PART II of this bulletin. These 
estimates are based on hands-on time, and may vary with personnel and facilities 
available. 
 
WARRANTY: 
 
There is no warranty credit applicable for parts or labor associated with this bulletin. 
 
MATERIAL: 
 
Required Material: 
The following material may be required for the accomplishment of this bulletin and 
may be obtained through your Bell Helicopter Textron Supply Center. 
 
Part Number Nomenclature  Qty   
    
205-001-720-001 Cabl e Assembly 2  
 
Consumable Material: 
The following material may be required to accomplish this bulletin, but may not require 
ordering, depending on the operator’s consumable material stock levels.  This material 
may be obtained through your Bell Helicopter Textron Supply Center. 
 
Part Number Nomenclature  Qty  Reference * 
    
AN23-11 Bolt 2  
AS100028 Lockwire AR C-405 
MS14145L3 Nut 2  
MS24665-151 Pin, Split 2  
NAS1149F0363P Washer 2  
 
* C-XXX numbers refer to the consumables list in BHT-ALL-SPM Standard Practices Manual 
 
SPECIAL TOOLS: 
 
None required.  
 
WEIGHT AND BALANCE: 
 
Not affected.

### Page 3

ASB 204B-12-68 
Page 3 of 6 
ECCN EAR99 
ELECTRICAL LOAD DATA: 
 
Not affected. 
 
REFERENCES: 
 
BHT-204B-M&O Maintenance and Overhaul Manual 
BHT-204B-IPB Illustrated Parts Breakdown 
 
PUBLICATIONS AFFECTED: 
 
None affected. 
 
ACCOMPLISHMENT INSTRUCTIONS: 
 
PART I - Inspection 
 
1. Prepare helicopter  for maintenance. 
2. Open the vertical fin tail rotor driveshaft cover. 
3. Gain access to the lower ends of t he P/N 205-001-720-001 cable assemblies at the 
connection to the P/N 0301245 barrel assembly. See Figure 1.  
4. Refer to Figure 1. Inspect for the conditi on shown in View B that prevents complete 
seating of the P/N 0301245 barrel assembly  in the bottom of the P/N 205-001-742-
001 body.  If necessary, remove lockwire for a clear view.  
5. The condition shown in Figu re 1, View B, is not accept able and is cause to replace 
the affected P/N 205-001-720-001 cable assembly. 
6. For cable assemblies that fully engage the P/N 0301245 barrel assembly and do 
not exhibit the condition of View B, no furt her action is required. If lockwire was 
removed to facilitate inspection, secure barrel assembly and cable connection with 
new lockwire and make an entry in helicop ter historical service records showing 
compliance with this ASB. 
7. For defective cable assemblies, go to PART II.

### Page 4

ASB 204B-12-68 
Page 4 of 6 
ECCN EAR99 
PART II – Replacement of Defective Cable Assemblies 
 
1. Replace defective cable a ssemblies within the next 100 f light hours after receipt of 
this ASB, whichever occurs first, but no later than 31 December 2012 . 
 
2. For defective cable assemblies that  are not to be replaced immediately: 
 
a. If lockwire was removed to facilitate inspection, secure barrel assembly and 
cable connection with new lockwire and ins pect daily for security and condition 
until cable assembly is replaced. 
 
b. Make an entry in helicopter historical services records noting that replacement 
of defective cable assemblies is required at the next scheduled inspection or 50 
flight hours after receipt of this ASB, whic hever occurs first, but no later than 31 
December 2012 . 
 
3. Refer to BHT-204B-M&O for ca ble replacement procedures.  
 
4. Once cable assemblies have been replaced, make an entry in helicopter historical 
service records indicating compliance with this Alert Service Bulletin.

### Page 5 (OCR)

CHAIN ASSE
205-001-720-001
CABLE ASSEMBLY
SEE VIEW A
205-001-720-001 CABLE ASSY
P/N 0301245  • 205-001-742-001 BODY
BARREL ASSY
A FALSE CUT IN THE BOTTOM OF THE
-742 BODY DOES NOT ALLOW FULL
ENGAGEMENT OF THE ATTACHING
BARREL ASSY - SEE VIEW B
VIEW A
(LOCKWIRE REMOVED)
Figure 1 (sheet 1 of 2)
ASB 204B-12-68
Page 5 of 6
ECCN EAR99

### Page 6 (OCR)

P/N 0301245
BARREL ASSY
205-001-742-001
BODY
VIEW B
DETAIL OF INTERFERENCE CREATED BY FALSE CUT IN BODY
Figure 1 (sheet 2 of 2)
ASB 204B-12-68
Page 6 of 6
ECCN EAR99

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
