# Bell Alert Service Bulletin 206L-20-184: Revision C

- Rights: © Bell Textron Inc. Filed by the FAA in regulations.gov docket FAA-2022-1488, the docket of AD 2023-06-05. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Bell Alert Service Bulletin 206L-20-184](https://openairdocs.org/service-documents/bell/206l-20-184.md)
- Title as filed: Bell ASB-206L-20-184 Rev C
- Pages: 14
- PDF: https://openairdocs.org/files/sha256/ab/5b/ab5b0eb3fac44cbbec00dffafa37ead7137febcd4301f9e521fad097c653761b
- Page: https://openairdocs.org/service-documents/bell/206l-20-184/file/ab5b0eb3fac4

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ASB 206L-20-184-RC 
Page 1 of 14 
Approved for public release. 
 
 
  ALERT SERVICE BULLETIN 206L-20-184 
21 July 2020 
Revision A, 21 August 2020 
Revision B, 20 October 2020 
Revision C, 14 January 2021 
 
 
MODEL AFFECTED:  206L, 206L-1, 206L-3 and 206L-4 
 
SUBJECT: SEGMENTED TAIL ROTOR DRIVESHAFTS 206-
040-369-001/-101, 206-040-365-001/-117/-125 WITH 
BONDED ADAPTERS, PROOF LOAD TEST OF. 
 
HELICOPTERS AFFECTED: Serial number s 45001 through 45153, 46601 
through 46617, 45154 through 45790, 51001 
through 51612, 52001 through 52223 . 
 
COMPLIANCE: PART I Within 75 flight hours or 3 months, whichever 
comes first, after the release date of this bulletin and  
every 300 flight hours or 12 months thereafter. 
 
 PART II At customer’s option. 
 
DESCRIPTION: 
 
Bell has received reports of disbonds of the bonded adapters on the segmented tail 
rotor driveshaft part numbers 206-040-369-101 and 206-040-931-009. Disbonding of a 
tail rotor driveshaft adapter can result in a loss of tail rotor drive and control of the 
helicopter. This Alert Servic e Bulletin (ASB) introduces an initial, and recurring proof 
load testing procedure of  installed bonded tail rotor driveshafts to verify the integrity of 
the bond line.  If an affected bonded tail rotor driveshaft assembly fails the proof load 
test, it is to be replaced with a serviceable segmented bonded driveshaft as per the 
applicable Maintenance Manual or by a riveted tail rotor driveshaft using the instructions 
in the Technical Bulletin 206L-02-207. PART II of this ASB provides a terminating action 
to PART I , with the replacement of all bonded tail rotor driveshaft assemblies with 
riveted tail rotor driveshafts using the information published in t he Technical Bulletin 
206L-02-207. Applicability of this bulletin to any spare part shall be determined prior to 
its installation on an affected helicopter.

### Page 2

ASB 206L-20-184-RC 
Page 2 of 14 
Approved for public release. 
Revision A allows failed bonded tail rotor driveshafts to be replaced with serviceable 
bonded driveshafts that meet the intent of this bulletin and makes corrections to some 
of the metric dimensions in Figure 1 of this bulletin. Revision B introduces a new work 
aid to hold the forward end of the sliding adapter 206-040-373 used with the forwa rd 
short shaft 406-040-315-111. The new work aid is not procurable and is to be locally 
manufactured (Figure 3) . Revision C  corrects the part numbers  in Step 1 1 of the 
Accomplishment Instructions. 
 
APPROVAL: 
 
The engineering design aspects of this bulletin are Transport Canada Civil Aviation 
(TCCA) approved. 
 
CONTACT INFO: 
 
For any questions regarding this bulletin, please contact: 
 
Bell Product Support Engineering 
LIGHT Tel: 450-437-2862 / 1-800-363-8023 / productsupport@bellflight.com 
 
MANPOWER: 
 
Approximately 1.5 man-hour is required to complete PART I of this bulletin. 
Approximately 12.0 man-hours are required to complete PART II of this bulletin. 
This estimate is based on hands-on time and may vary with personnel and facilities 
available. 
 
WARRANTY: 
 
There is no warranty credit applicable for parts or labor associated with this bulletin. 
 
MATERIAL: 
 
Required Material: 
The following material may be required for the accomplishment of this bulletin and may 
be obtained through your Bell Supply Center. 
 
Part Number Nomenclature Qty (Note) 
   
206-040-383-101 
206-040-385-101 
206-040-339-101 
9440904 
Aft Short Shaft (riveted) 
Shaft Assembly (riveted) 
Bearing 
Disk 
1 (1) 
5 (1) 
5 (2) 
1 (1)

### Page 3

ASB 206L-20-184-RC 
Page 3 of 14 
Approved for public release. 
NOTES: 
 
1. Quantity as required. Affected driveshafts may be replaced individually or the 
complete set may be replaced as per Technical Bulletin 206L -02-207. The rotor 
brake disk is required anytime one or all the riveted shafts are installed. The purpose 
of the rotor brake disk is to reduce the effect of the torsional load due to the increased 
stiffness of the riveted shaft(s). 
 
2. Bearing 206-040-339-103 is an approved alternate to bearing 206-040-339-101. 
 
Consumable Material: 
 
The following material is required to accomplish this bulletin, but may not require 
ordering, depending on the operator’s consumable material stock levels.  This material 
may be obtained through your Bell Supply Center. 
 
Part Number Nomenclature Qty (Note) Reference * 
    
2100-09016-02 CPC, MIL-PRF-16173 GR2 1 PT (1) C-104 
 
* C-XXX numbers refer to the consumables list in the BHT-ALL-SPM, Standard Practices Manual 
 
NOTE 1: The quantity indicated is the format the product is delivered in. Actual quantity 
required to accomplish the instructions in this bulletin may be less. 
 
SPECIAL TOOLS: 
 
The bonded shaft tool part number 206-244-001-101 (QTY 2 required) can be procured 
through your Bell Supply Center or locally manufactured (Figure 2). 
 
WEIGHT AND BALANCE: 
 
Weight and balance adjustments is only required for  the installation of the rotor brake 
disk. Refer to the Weight and Balance paragraph in Technical Bulletin 206L-02-207. 
 
ELECTRICAL LOAD DATA: 
 
Not affected. 
 
REFERENCES: 
 
BHT-206L-MM Maintenance Manual, Chapters 53 and 66 
BHT-206L1-MM Maintenance Manual, Chapters 53 and 66 
BHT-206L3-MM Maintenance Manual, Chapters 53, 65, and 71 
BHT-206L4-MM Maintenance Manual, Chapters 53, 65, and 71 
BHT-ALL-SPM, Standard Practice Manual, Chapter 2 
Technical Bulletin 206L-02-207

### Page 4

ASB 206L-20-184-RC 
Page 4 of 14 
Approved for public release. 
PUBLICATIONS AFFECTED: 
 
BHT-206L-MM Maintenance Manual, Chapters 5 and 66 
BHT-206L1-MM Maintenance Manual, Chapters 5 and 66 
BHT-206L3-MM Maintenance Manual, Chapters 5 and 65 
BHT-206L4-MM Maintenance Manual, Chapters 5 and 65 
 
ACCOMPLISHMENT INSTRUCTIONS: 
 
PART I – Proof load test procedure 
 
1. Prepare the helicopter for maintenance and gain access to the tail rotor driveshafts . 
(applicable 206L Maintenance Manual)  
2. Verify the part numbers of the segmented tail rotor driveshafts installed. If all the tail 
rotor driveshafts are riveted tail rotor driveshafts (206-040-383-101 and 206-040-385-
101) go to step 15, otherwise go to step 3.  Having all riveted tail rotor drive shafts is 
considered meeting the intent of PART II of this ASB and a terminating action to 
PART I. 
3. Carry out a detailed visual inspection of the bond line on the inboard end of the flange 
of the bonded tail rotor driveshafts using a 10X magnifying glass  (Figure 1). If the 
bond line area shows damage such as cracked or missing adhesive or evidence of 
corrosion, the affected shaft is deemed un -repairable and must be removed from 
service and  scrapped. Replace affected driveshaft (s) with a riveted tail rotor 
driveshaft(s) (TB 206L-02-207). 
-NOTE- 
 
Two people are required to carry out the proof load testing 
procedure of the bonded tail rotor driveshafts.  Proof loading 
of the shafts is carried out with the shafts installed  on the 
helicopter. 
 
4. Index-mark each bonded tail rotor driveshaft and adapters with a fine tip felt marker 
(Figure 1) and number the shafts (example: Aft SS, 1, 2, 3, 4 and, 5.  Driveshaft #5 
being the closest to the tail rotor gearbox). 
-NOTE- 
 
If the forward short shaft is removed, install the (206-040-328) 
sliding adapter and work aid (Bonded Shaft Tool 206 -244-
001-101) on the forward splines of the oil cooler fan shaft. The 
bonded shaft tool 206 -244-001-101 can be locally 
manufactured using the information in  Figure 2 or can be 
purchased from a Bell Supply Center.

### Page 5

ASB 206L-20-184-RC 
Page 5 of 14 
Approved for public release. 
-NOTE- 
 
The forward short shaft must be removed on helicopters 
equipped with the larger 406-040-315-111 forward short shaft.  
The locally manufactured work aid shown in Figure 3 must be 
used on the 206-040-373 sliding adapter on the forward 
splines of the oil cooler fan shaft. The sliding adapter work aid 
(Figure 3) may also be used to hol d the 206-040-328 sliding 
adapter on the forward splines of the oil fan shaft  (the work 
aid has both hole patterns). In either case, the forward sh ort 
shaft must be removed when using this work aid. Figure 4 
shows the installation o f the work aids required for the proof 
load test. As an alternate, a 206-040-328 sliding adapter could 
also be used to carry out the proof load test. 
 
5. For 206L1 or 206L3 modified by BHT -206-SI-2052 ( Increased Gross Weight 
Upgrade Kit) or 206L4 serial numbers 52001 through 52 223 with bonded tail rotor 
driveshafts and the forward short shaft 406-040-315-111, do the following:    
a. Remove forward short shaft 406-040-315-111 (applicable Maintenance Manual). 
b. Attach the 206-040-373 / 206-040-328 sliding adapter work aid on the forward 
face of the fan shaft sliding adapter  (206-040-373) using two (2) AN175-12 or 
NAS6605-12 bolts, washers AN960 -516L, and MS 35650-3312 nuts, or 
equivalent (Figure 4). 
c. Go to step 7. 
6. For all other affected helicopters, with the forward short shaft  (206-040-325) 
installed, install the bonded shaft tool 206-244-001-101 on the aft face of the sliding 
adapter (206-040-328) flange on the forward splines of the oil cooler blower shaft 
using two (2) AN174 -12 of NAS6604 -12 bolts, current washers AN960 -416L, and 
nuts MS21042L4, NAS9926-4L or a MS35650-3252 nut, or equivalent. 
a. If the forward short sh aft (206-040-325) has been removed, install the bonded 
shaft tool 206-244-001-101, or the 206-040-373 / 206 -040-328 sliding adapter 
work aid, on the forward face of the sliding adapter (206-040-328) on the forward 
splines of the oil cooler blower shaft using two  (2) AN174-12 or NAS660 4-12 
bolts, current washers AN960-416L, and nuts  MS21042L4, NAS9926 -4L or  a  
MS35650-3252 nut, or equivalent (Figure 4 or 5). 
7. Remove two (2) AN174 bolts from the (206-040-328) sliding adapter on the input 
pinion of the tail rotor gearbox.

### Page 6

ASB 206L-20-184-RC 
Page 6 of 14 
Approved for public release. 
8. Install the second bonded shaft tool on the aft face of the sliding adapter (206 -040-
328) of the input pinion of the tail rotor gearbox using two (2) AN174-12 of NAS6604-
12 bolts, current washers AN960 -416L, and nuts MS21042L4, NAS9926 -4L or a 
MS35650-3252 nut, or equivalent (Figure 5). 
 
-NOTE- 
 
This following step may be carried out from either the left or 
right side of the helicopter depending on access. 
 
9. One person is required to hold the bonded shaft tool 206-244-001-101 with a ½-inch 
square drive breaker bar, or the 206-040-373 / 206-040-328 sliding adapter work aid, 
on the splines of the forward end of the oil cooler blower shaft (Figure 6). 
WARNING 
 
To avoid personnel injury, use caution when carrying out the 
proof load testing in case of a sudden bond separation  of the 
tail rotor driveshafts. 
CAUTION 
 
Protect the fuselage and tailboom adequately to prevent 
damage that may be caused by the breaker bar, torque 
wrench, and bonded shaft tools. 
 
10.  One person is required to hold the torque wrench on the bonded shaft tool installed 
on the sliding adapter (206-040-328) of the tail rotor gearbox input pinion (Figure 6). 
-NOTE- 
 
Use a ½-inch square drive dial-type torque wrench capable of 
measuring up to 150 foot-pounds (237 Newton-meters). Refer 
to BHT-ALL-SPM, Figures 2 -1, 2-2, and 2-3 concentric and 
non-concentric type attachments. Examples of torque values 
when using concentri c and nonconcentric attachments are 
shown in Figure 7. 
 
11. Carry out the proof load testing of the installed tail rotor driveshafts by applying the 
equivalent of 123 foot -pounds ( 167 Newton-meters) of torque to the  1.25-inch 
diameter shafts 206-040-369-001/-101 and 206-040-365-001/-117/-125.

### Page 7

ASB 206L-20-184-RC 
Page 7 of 14 
Approved for public release. 
-NOTE- 
 
Unserviceable bonded tail rotor driveshafts may be replaced 
individually with riveted driveshafts  or as a complete set as 
per Technical Bulletin 206L-02-207. 
 
12. In the event of a bond line failure, record the torque value at which it failed  as well 
as the affected shaft position, part number, serial number  and which end failed. 
Notify Bell Product Support Engineering of the findings. Replace the affected 
driveshaft with a serviceable  bonded tail rotor  driveshaft as per the applicable 
Maintenance Manual or a riveted tail rotor driveshaft (TB 206L-02-207) and repeat 
step 11.  
13. Following the proof load testing, carry out a detailed visual inspection of the bond 
line on the inboard end of the flange of the tail rotor driveshafts using a 10X 
magnifying glass to ensure there was no movement of the bonded adapter during 
the proof load testing. 
14. If removed, install forward short shaft 406-040-315-111 or 206 -040-325, as 
applicable (applicable Maintenance Manual) 
15. After the proof load testing procedure has been successfully carried out, re -install 
previously removed attach ing hardware (applicable 206L Maintenance Manual,  
Chapters 53, 65, and 71) . Carry out the torque check of the disc pack coupling 
hardware per Maintenance Manual Chapter 5 requirements. 
16. Make an entry in the helicopter logbook and historical service records indicating 
findings and compliance with PART I of this Alert Service Bulletin. 
17. If PART II of this ASB has not been accomplished, repeat PART I every 300 hours 
or 12 months, whichever comes first. 
 
PART II – Installation of riveted tail rotor driveshafts 
 
-NOTE- 
 
PART II of this ASB is considered a terminating action to the 
requirements of PART I  when all bonded driveshafts hav e 
been replaced with riveted tail rotor driveshafts. 
 
1. Prepare helicopter for maintenance. 
2. Remove all bonded tail rotor driveshafts and install rivet tail rotor driveshafts  206-
040-383-101 and 206-040-385-105, in all locations as applicable (Technical Bulletin 
206L-02-207).

### Page 8 (OCR)

3. Make an entry in the helicopter logbook and historical service records indicating
compliance with PART II of this Alert Service Bulletin.
206-040-330
END STOPPER  206-040-369 AFT SHORT SHAFT (ALUMINUM)
(2 PLACES)
BONDED SEGMENTED SHAFT
(206-040-931/206-040-365)
10X INSPECTION OF THE BOND LINE ON
INBOARD END OF BONDED ADAPTERS
#3  #4
Figure 1 - Example of Tail Rotor Driveshaft Numbering and Index Marking
ASB 206L-20-184-RC
• Page 8 of 14
Approved for public release.

### Page 9 (OCR)

3.15  IN.
(80.0 mm)  .92  IN.
0.69 IN. DIA.  (2 PLACES)  (23.4 mm)
(17.5 mm)  3.00  IN .  (2 PLACES)
(TYPICAL)  (76.2 mm)  .60 IN.
(15.2 mm)
1.20 IN.
(30.5 mm)
.031 IN.RAD.  1.52 IN.
3.04  (0.79 mm)  (38.6 mm)
(77.2 mm)  (TYPICAL)
1.172 IN
(29.77 mm)  .83  IN.RAD.
(2 PLACES)
(21.1 mm)
.51 IN
(12.9 mm)
0.266 - 0.272 IN. DIA.  0.505 - 0.520 IN
(6.76 - 6.91 mm)  (12.83 - 13.21 mm)
(TYPICAL)
3.23
(82.0 mm)
3.90  IN
(99.1 mm)
.375  IN.
(9.53 mm)
NOTES:
1. Material: (optional) steel or aluminum, thickness 0.375 IN. (9.53 mm).
2. Break all sharp edges: 0.015 IN. (0.38 mm) radius or 0.015 IN. (0.38 mm) × 45' chamfer.
Figure 2 - Bonded Shaft Tool (206-244-001-101)
(May be ordered or locally manufactured)
ASB 206L-20-184-RC
Page 9 of 14
Approved for public release.

### Page 10 (OCR)

30.00
(17.5 mm)  .69  (66.55 - 66.80 mm)  2.630  2.620  206-040-373 ADAPTER REF  (762 mm)  (59.41 - 59.66 mm)  2.349  2.339  (14.2 mm)  . 56
206-040-328 ADAPTER REF
50(38.1 mm)  206-040-378 ADAPTER  208-040-328 ADAPTER >
-HOLE PATTERN  HOLE PATTERN
. 75  R .25 TYP  8. 334  2 PL  Ø•272 2 PL  .75
(19.1 mm)  (6.4 mm)  328  .266  (19.1 mm)
(8.33 - 8.48 mm)  (6.76 - 6.91 mm)
NOTES:
1. All dimensions in Inches. Dimensions in parentheses are millimeters.
2. Material: (optional) steel or aluminum, thickness 0.375 IN. (9.53 mm).
3. Break all sharp edges: 0.015 IN. (0.38 mm) radius or 0.015 IN. (0.38 mm) × 45° chamfer.
4. Mark adapter part numbers as shown by vibro-etch, stamping, dot peen or other permanent method.
Figure 3 - 206-040-373 / 206-040-328 Sliding Adapter Work Aid
(Locally manufacture - Not available for purchase)
ASB 206L-20-184-RC
Page 10 of 14
Approved for public release.

### Page 11

ASB 206L-20-184-RC 
Page 11 of 14 
Approved for public release. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 4 – Bonded Shaft Work Aid Installation  
Work Aid Tool for 
206-040-373-101 
206-040-373-101 
Adapter 
206-244-001-101 
Torque Work Aid 
206-040-328-003 
Adapter 
Work Aid has hole patterns for both 206-
040-373 and 206 -040-328 adapters, 
depending on installation 
206-040-373-101 
Adapter 
206-040-328-003 
Adapter 
206-040-328-003 
Adapter

### Page 12

ASB 206L-20-184-RC 
Page 12 of 14 
Approved for public release. 
 
 
 
 
 
 
Figure 5 - Examples of Bonded Shaft Tool Installations

### Page 13

ASB 206L-20-184-RC 
Page 13 of 14 
Approved for public release. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
   
 
 
 
 
 
 
Figure 6 – Proof Load Testing  
Blue arrow indicates direction 
of torque to be applied

### Page 14 (OCR)

' 90°
90°
NOTE
Applied and indicated torque values are the same.
Torque Wrench Concentric Type Attachments
(Ref) BHT-ALL-SPM, Chapter 2
2 IN.  12 IN.
FORMULA TO OBTAIN CORRECT INDICATED  (50.8 mm)  (304.8 mm)
TORQUE VALUE WHEN USING  L
NONCONCENTRIC ATTACHMENT
200 IN-LBS
TW = (TA) X (L)  (22.60 Nm)
(L) = (A)  TA  • TW
TW = INDICATED TORQUE VALUE ON
TORQUE WRENCH
TA = ACTUAL TORQUE VALUE APPLIED
TO FASTENER  TW = 200 X 12 = 2400 = 171.4 IN-LBS (19.37 Nm)  12 + 2
L = LEVEL LENGTH
A = ATTACHMENT LENGTH  RESULTS: FASTENER TORQUED 200 IN-LBS
(22.60 Nm) WHEN WRENCH
INDICATES 171.4 IN-LBS (19.37 Nm)
FORMULA  EXAMPLE 1
Figure 7 - Example of Nonconcentric Type Attachments
(Ref) BHT-ALL-SPM, Chapter 2
ASB 206L-20-184-RC
Page 14 of 14
Approved for public release.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
