# Bell Alert Service Bulletin 206L-87-47: Revision C

- Rights: © Bell Textron Inc. Filed by the FAA in regulations.gov docket FAA-2008-1242; AD 96-18-05 R1 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Bell Alert Service Bulletin 206L-87-47](https://openairdocs.org/service-documents/bell/206l-87-47.md)
- Title as filed: Bell ASB 206L-87-47
- Pages: 11
- PDF: https://openairdocs.org/files/sha256/ce/f9/cef9680c6ce4dc5b876fdbb6d921434ee81d0c62462e500ec9050ea4b1e96018
- Page: https://openairdocs.org/service-documents/bell/206l-87-47/file/cef9680c6ce4

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

ALERT SERVICE BULLETIN  NO. 206I-87-47
Bell Helicopter TEXTRON  DATE 8-12-87
DATE 10-23-89  A Subsidiary of Textron Inc
REV.  "C"  Post Office Box 482 • Fort Worth, Texas 76101  PAGE NO. 1 of 11
MODEL AFFECTED:  2061, 2061-I, 2061-111
SUBJECT:  TAILBOOMS,  P/N 206-033-004-3/-11/-103/-45
PERIODIC INSPECTION OF, MODIFICATION OF
HELICOPTERS AFFECTED:  All  model  2061  series helicopters S/N
45001 through 51283.
[A1]  model 206L-3  helicopters S/N 51284
and subsequent will have the intent of
this  bulletin  accomplished  prior  to
delivery.l
COMPLIANCE:
Part I:  Modification  tailboom shall be accom-
plished not later than Dec. 1, 1989.
Part II: Interim  inspection of unmodified tailboom
shall be accomplished every 50 hrs.
Part III: Periodic  inspection  of field  modified
tailbooms and tailbooms subsequent to -45,
shall be accomplished every 100 hrs.
DESCRIPTION:
Bell Helicopter Textron  has received  several reports of severe
upper skin cracks in tailbooms, P/N 206-033-004-3/-11/-103/-45 in
area  of aft most drive shaft cover retention clip (Boom Station
153.79). Improperly secured tail rotor gearbox, unbalanced tail-
prove and repair akin damage on  and added mass such as antenna, and/or lights which are not
approved by Bell Helicopter Textron may be major causes. Failure to
and repair skin damage on tailboom could result in tailboom
failure.
This bulletin provides:
Modification  instructions  increase structural integrity of
tailboom at BS. 153.79.
-  50 hr. interim inspection requirements for unmodified tailbooms.
7851 55192 REV. 1278  100  hr .  periodic  inspection requirements  for field modified
tailbooms and tailbooms subsequent to -45.
NOTE
The -103 tailboom precedes -45 tailboom.
AN APPROPRIATE ENTRY SHOULD BE MADE IN THE AIRCRAFT LOG BOOK UPON ACCOMPLISHMENT
IF OWNERSHIP OF AIRCRAFT HAS CHANGED PLEASE FORWARD TO NEW OWNER

### Page 2 (OCR)

A.S.B. 206L-87-47
Page 2 of 11
FAA APPROVAL:
The engineering design aspect of this bulletin is FAA approved.
MANPOWER:
Part I  Modification of tailboom will require an estimated eight
(8.0)  manhours. Actual time may vary due to manpower and
facilities available to the operator.
Part II  Inspection will require approximately eight tenths (0.8)
manhours for each 50 hour inspection.
Part III  Inspection  requirements will  not significantly affect
regular  100 hour  periodic  inspection, if accomplished
during scheduled inspection.
MATERIALS:
The following parts necessary to accomplish this tailboom modifica-
tion may be purchased from your BHTI spare parts supply source.
PART NUMBER  NOMENCLATURE  QTY.
206-033-407-119  clip  CAPACE
206-704-167-111  Doubler
M7885/6-4-02  Rivet
MS20426AD4-4  Rivet
50-021-1  Receptacle
299-947-125TY2CL2 5 oz.  Adhesive (EA9320NA)
MILS8802CLB2 6 oz.  Sealant
M7885/6-4-03  Rivet
M7885/7-4-02  Rivet  3  "C"
M7885/7-4-03  Rivet  11
WEIGHT AND BALANCE:
WEIGHT  MOMENT
Part 1, Longitudinal  +.6 1bs.  +212 1b. in.
ELECTRICAL LOAD DATA:
Not affected.
SPECIAL TOOLS:
Standard aviation sheet metal hand tools required.
REFERENCES:
Maintenance Manual, Sec. 5-3-9

### Page 3 (OCR)

A.S.B. 206L-87-47
Page 3 of 11
PUBLICATIONS AFFECTED:
Maintenance Manual, Sec. 5
Illustrated Parts Catalog, Sec. 53
ACCOMPLISHMENT INSTRUCTIONS:
PART I: MODIFICATION OF TAILBOOM
1) Remove  - T/R driveshaft cover
- Aft segment of T/R driveshaft
- T/R gearbox fairings
- Anti-chafing tape as required
2) Remove existing T/R driveshaft cover retention clips (2 ea.)
at BS. 153.79.
3) Inspect  for cracks and corrosion at rivet holes using a 5X
magnifying glass. In the event that cracks are revealed, you
are requested to contact:
Bell Helicopter Textron
Product Support Engineering
TEL: 1-800-363-8023 from the Continental US
TEL: 1-800-361-9305 within Canada
TELE 514-435-0212  TEL: 514-437-2862 from other areas
TELEX: 05-835580 - BELL SJAN
HELICOMM: PSECAN
NOTE
The doubler  in this modification is not
intended as a remedy for cracked skins. It  "C"
is  a preventative  measure for undamaged
skins.
Refer to Maintenance Manual for corrosion and pitting limits.
" Fired on Lower. B00 Ta. ?
5) Strip  paint from area  of top skin between B.S. 151.15 and
B.S. 159.35 and from new clip faying surface.
6) Fit doubler P/N 206-704-167-111 to tailboom such that leading
edge of doubler is at B.S. 151.15 and drill to match existing
holes along seams and 4 existing clip rivet holes.

### Page 4 (OCR)

A.S.B. 206L-87-47
Page 4 of 11
NOTE
may  be  necessary to trim doubler to prevent
interference with adjacent rivet (s).
If required, grind off adhesive bumps on inside of
doubler which may interfere with proper fitting of
doubler to tailboom.
Do not remove fabric peel ply at this time.
The doubler will be supplied with pilot holes. Note that most
of rivets consists of 10 rivets equally
spaced between the upper and lower skin seam rivet lines. The
second and third rows of rivets are made up of 5 rivets each
equally spaced between the lower skin seam rivet line and the
LH extremity of the new clip, P/N 206-033-407-119. The fourth
and fifth  consist  10 rivets each, equally spaced
between the upper and lower skin  seam rivet lines.
NOTE
Doubler  rivet  rows  spaced 1.0 inch from
seam rivet lines. See Figure 3, Sec. B-B.
Five (5) rows of rivets are equally spaced from
back of doubler. Maintain a 2D edge
distance. See Figure 2.
8) With  doubler held in place, position saddle clip, P/N 206-
033-407-119,  at B.S.  153.79  to align with T/R drive shaft
cover and pickup on 4 existing clip rivet holes. In addition,
two rivet holes 1.0 inch each side of the longitudinal
C/L of tailboom. Maintain 2D edge distance. See Figures 2 and
3, Sec. A-A.
Drill all holes in tailboom, doubler and clip to proper rivet
size. Countersink to  a max. depth of .038 inch in 14
places for M7885/7 or NAS1739B4 rivets (see Figure 2 and 3
for locations). Remove clip and doubler and deburr holes both
sides including tailboom skin.
NOTE
If  next  larger size  rivet  is  required for
M7885/7-4  rivet, use only CR3214-5 rivet. May be
purchased  commercially  from Cherry Max Rivet  "C"
Outlet or Townsend Division of Textron, Inc., 1224
East Warner Ave., Santa Ana, Calif. 92707.

### Page 5 (OCR)

A.S.B. 206L-87-47
Page 5 of 11
10) Remove  fabric peel ply from doubler and scuff adhesive with
400 grit sandpaper, wipe clean with clean cheesecloth dampen-
ed with M.E.K. and  air dry.
11) Clean and prepare  all other surfaces to be bonded by scuffing
lightly  dampened with M.E.K. and air dry.  with  #400  sandpaper. Wipe clean with cloth
12) Adhesive  application  - after thoroughly mixing, the EA9320
adhesive  applied by non-metallic spatula, notched
trowel, or wood applicator. Adhesive shall be applied .002 to
.004 inch thick on faying surfaces.
NOTE
Pot life of adhesive is 25 minutes.
13) With  adhesive  applied to fayin secure using  surfaces  of doubler and
tailboom,  position  doubler and  appropriate
rivets, per Figure 2.
14) Apply  adhesive to top of doubler and to clip faying surfaces,
position  clip  on doubler and secure to tailboom using 8
M7885/6-4-03 rivets.
15) Remove adhesive squeeze-out and allow to cure for 24 hours
degrees  Curing  can be accelerated by heating to 180
degrees F. ‡ 5 degrees F. for 1 hour. Do not overheat.
16) Install  receptacle P/N  50-021-1 on clip. Position to match
P/N 206-033-407  cover and secure using MS20426AD4-4 rivets.
(See  Fig. 3),  Sec. A-A. Ensure that fastener stud does not
come into contact with clip saddle when secured.
17) Apply a brush coat of alodine to bare aluminum areas and to
rivet heads.
18) Seal  all edges of doubler and clip using MILS8802. (See Fig.
2.)
19) Prime using polyamide epoxy primer and repaint affected area. "c"
20) Reidentify tailboom by adding the suffix "FM" to the original
P/N.
ORIGINAL P/N  MODIFIED P/N
206-033-004-45  206-033-004-45 FM
206-033-004-11  206-033-004-11 FM
206-033-004-3  206-033-004-3 FM
206-033-004-103  206-033-004-103 FM

### Page 6 (OCR)

A.S.B. 2061-8-47
Page 6 of 11
21) Install  - T/R Driveshaft
- T/R Gearbox Cowlings
- Anti-Friction Tape as Required
- T/R Driveshaft Cover
206L SERIES TAILBOOM
CLIP MODIFICATION
B.S. 153.79
B.S
153.79
REF
C
Clip
206-033-407-119
- Doubler
206-704-167-111
-See Fig. 2 & 3 for
rivet pattern
- MIL-S -8802
Edge sealant
FIGURE I

### Page 7 (OCR)

A.S.B. 206L-87-47
Page 7 of 11
remove 11 rivets
& replace with
MS7885/7-4-03
B.S.
B.S.  159.35
151.15  ref
M7885/6-4-03
(4 of)
1.0 in. typ.
Note 1  MIL-S-8802-  •Pick up existing rivet
seal all edges of  locations and replace
clip and doubler  with M7885/6-4-03
B.S.  (4 of)
153.79
- .2D edge dist.
typ.
M7885/7-4-02
( 30F )
-111)
M7885/6-4-02
Doubler
(37 OF )
1.0 in. typ
B-
Remove 9 rivets and
replace with
M7885/6-4-03
FIGURE 2

### Page 8 (OCR)

A.S.B. 206I-87-47
Page 8 of 11
- Clip
206-033-407-119
Adhesive  1.00  -531
EA9320NA  - 539
Hole thru clip (2pl.) to
TYP  match 206-033-407
cover. 50-021-1 recep -
tacle 2 reqd.
MS20426AD4-4 rivet
4 read.
Doubler
206-704-167-111
SECTION A-A
-1.00
Rivet -
M7885/7-4-02  Rivet
(3 of)  M7885/7-4-03
See note par. 9  (11 of)
page 4.  page 4  See note par.9  C
Rivet
MS7885/6-4-02
(37 of)
1.00
Rivet
MS7885/6-4-03
(9 of)  SECTION B-B
FIGURE 3

### Page 9 (OCR)

A.S.B. 206L-87-47
Page 9 of 11
PART II:  50 HOUR INSPECTION, UNMODIFIED TAILBOOMS
1) Remove T/R driveshaft and T/R gearbox fairings.
2) Remove a sufficient amount of anti-chafing tape to permit
inspection  shaft cover retention slips aft of horizontal stabilizer, and  tailboom  adjacent to tail rotor drive
area of double row  of rivets attaching the tail rotor
gearbox support fitting to the tailboom (B.S. 174).
3) Prior  cleaning, use a min. 5 power magnifying glass to
inspect  cracks  signs  of developing cracks at the
following locations: (See Fig. 4)
A) Aft of stabilizer  assy, around rivets which attach the
tail rotor drive  shaft  retention  clips to the
tailboom.
B) Area  of tail rotor gearbox fairing attachment nut plate
rivets.
C) area  of double row of rivets which attach the tail rotor
gearbox support fitting to the tailboom (B.S. 174).
4) Clean entire tailboom taking particular care to remove all
and dirt in  specified area of inspection and repeat
min. 5 power inspection as per sub-paragraph 3.
5) Visually inspect entire tailboom in accordance with mainten-
ance manual.
6) Replace any loose or working rivets found.
7) Replace anti-chafing tape removed as required.
8) In the  event that cracks are found, you are requested to
contact:
Bell Helicopter Textron
Product Support Engineering
TEL: 1-800-363-8023 from the Continental US
1-800-361-9305 within Canada
514-437-2862 from other areas
TELEX: 05-835580 BELL SJAN
FAX: 514-433-0272
HELICOMM: PSECAN

### Page 10 (OCR)

A.S.B. 206L-87-47
Page 10 of 11
UNMODIFIED TAILBOOM ASSY
4 Nutplates
(2 each side)
10 Clips
Double row
of rivets
B.S. 174
AREA TO BE INSPECTED
FIGURE 4

### Page 11 (OCR)

A.S.B. 206L-87-47
Page 11 of 11
PART III: 100  HOUR  INSPECTION,  FIELD  MODIFIED  TAILBOOMS  AND
TAILBOOMS SUBSEQUENT TO -45
1)  Inspect as per PART II. (Refer to Fig. 5)
2)  Inspect doubler and clip  eage  sealant for integrity.
Reseal as required. (See Fig. 2)
MODIFIED TAILBOOM ASSY
4 Nutplates
Clip  (2 each side)
206-033-407-119
8 Clips~
L Double row
of rivets
Doubler  B.S. 174
206-704-167-1|1
AREA TO BE INSPECTED
FIGURE 5

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
