# Bell Alert Service Bulletin 222U-00-57: No revision named

- Rights: © Bell Textron Inc. Filed by the FAA in regulations.gov docket FAA-2008-0449, the docket of AD 2008-19-02. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Bell Alert Service Bulletin 222U-00-57](https://openairdocs.org/service-documents/bell/222u-00-57.md)
- Title as filed: U.S. DOT/FAA - Bell ASB 222U-00-57
- Pages: 8
- PDF: https://openairdocs.org/files/sha256/db/e6/dbe600d9fe0013606fb4c00d1ec023dd9b7d9da463c1a0487af6b251e3b99b3d
- Page: https://openairdocs.org/service-documents/bell/222u-00-57/file/dbe600d9fe00

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

ALERT SERVICE BULLETIN
NO. 222U-00-57
Bell Helicopter TEXTRON
DATE  A Subsidiary af Tection Inc  DATE  05-19-00
REV  PAGE  1 of 6
MODEL AFFECTED:  Model 222U
SUBJECT:  HYDRAULIC ACTUATOR SUPPORT P/N 222-040-
125-001, INSPECTION OF
HELICOPTERS AFFECTED:  Model 222U helicopters serial number 47501
through 47574.
COMPLIANCE:  Within 25 hours following receipt of this bulletin.
DESCRIPTION:
A Model 222U helicopter was in flight when it experienced a control loss. The cause of
control loss was attributed to the main rotor hydraulic actuator support separating from
the transmission. All retaining studs were found sheared or pulled out at the junction of
the support with the transmission upper and lower cases.
The purpose of this bulletin is to require a one-time inspection of the hydraulic
actuators support installation by accomplishing a torque check of the support attaching
nuts. In addition, a Revision to the maintenance manual will introduce a recurring
torque check of the support attaching nuts.
APPROVAL:
Not required
MANPOWER:
Approximately 5 man-hour is required to complete this bulletin if the support is not
7851 55192 REV 1198  removed from the transmission. An additional 6 man-hours will be required to remove,
inspect and reinstall the support. Man-hours are based on hands-on time, and may
vary with personnel and facilities available.
AN APPROPRIATE ENTRY SHOULD BE MADE IN THE AIRCRAFT LOG BOOK UPON ACCOMPLISHMENT
IF OWNERSHIP OF AIRCRAFT HAS CHANGED PLEASE FORWARD TO NEW OWNER

### Page 2 (OCR)

222U-00-57
Page 2 of 6
MATERIAL:
Required Material:
The following material is required for the accomplishment of this bulletin and may be
obtained through your Bell Helicopter Textron Supply Center.
Part Number  Nomenclature  Quantity
* MS21042L4  Nut  4
* MS21042L5  Nut  4
* 222-040-268-001  Washer  4
* 222-040-268-003  Washer  4
* Nuts are required only if actuator support is removed for inspection.
Consumable Material:
The following material is required to accomplish this bulletin, but may not require
ordering, depending on the operator's consumable material stock levels. This material
may be obtained through your Bell Helicopter Textron Supply Center.
Part Number  Nomenclature  Quantity  Reference
* MILS8784CLB2  Sealant  3.5OZ  C-328
* Sealant is required only if actuator support is removed for inspection.
SPECIAL TOOLS:
None required
WEIGHT AND BALANCE:
Not affected
ELECTRICAL LOAD DATA:
Not affected

### Page 3 (OCR)

222U-00-57
Page 3 of 6
REFERENCES:
BHT-222U-MM-6, Chapter 63
BHT-222U-MM-9, Chapter 71
BHT-222-CR&O-2, Chapter 63
BHT-ALL SPM
PUBLICATIONS AFFECTED:
BHT-222U-MM-2, Chapter 5
BHT-222-CR&O-2, Chapter 63
ACCOMPLISHMENT INSTRUCTIONS:
1. Remove fairings and cowlings as required to gain access to the hydraulic actuators
support. Refer to BHT-222U-MM-9, Chapter 71.
2. Verify that the dowel pins installed in the transmission upper case are not missing
and that evidence of sealant is present at the joint between the actuator support
and the transmission. Refer to figure 2. If any of the pins are missing and/or if no
sealant is visible, remove the actuator support and proceed to step 5.
3. Verify torque of actuators support P/N 222-040-125-001 attaching nuts. Apply the
torque in the tightening direction. For the upper row of nuts, if 40 in. Ib. is reached
without nut movement, increase the torque to 50-70 in.lb plus tare. For the lower
row of nuts, if 90 in. Ib. is reached without nut movement, increase the torque to
100-140 in. Ib plus tare.
-NOTE-
Anti fretting washers installed between the actuator support
and the transmission lower case may be reinstalled provided
the coating is not worn through or damaged
4. If two or more of the nuts within the upper row of the support attaching nuts move
below 40 in.Ib torque or two or more of the nuts within the lower row of the support
attaching nuts move below 90 in.Ib torque, remove the hydraulic actuators support
from the transmission for further inspection and repair. Refer to BHT-222U-MM-6,
Chapter 63 and BHT-222-CR&0-2, Chapter 63 for removal instructions. Discard
nuts and washers.
5. If required, inspect the support P/N 222-040-125-001 in accordance with
instructions in BHT-222-CR&O-2, Chapter 63. The holes at the lower and upper
end of the support were manufactured to the dimensions shown in figure 1.

### Page 4 (OCR)

222U-00-57
Page 4 of 6
6. If required, inspect the transmission lower case assembly as follows:
a) Inspect surface of transmission case in contact with the actuator support for
damage, fretting and corrosion. Refer to BHT-222-CR&O-2, Chapter 63 for
damage/wear limits.
b) Inspect the studs, retaining the actuators support, for condition of threads and
for looseness. Replace damaged studs in accordance with BHT-222-CR&O-2,
Chapter 63 and BHT-ALL-SPM.
7. If required, inspect the transmission upper case assembly as follows:
a) Inspect surface of transmission case in contact with the actuator support for
damage, fretting and corrosion. Maximum depth and/or size of corrosion, wear,
scratches, nicks and marks shall not exceed 0.005 inch depth, 40% of any one
square inch or more than 20% of the total surface. Pitting/corrosion around
studs and dowel pins shall not exceed 0.005 depth or 50% of the circumference
of the stud/dowel pin.
b) Inspect the studs, retaining the actuators support, for condition of threads and
for looseness. Replace damaged studs in accordance with BHT-222-CR&0-2,
Chapter 63 and BHT-ALL-SPM.
c) Inspect the dowel pins in transmission case for damage, fretting , corrosion and
looseness. The large outboard pins should measure 0.500 inch minimum and
protrude 0.55 inch from the surface of the case. The small inboard pins should
measure 0.375 inch minimum and protrude 0.45 inch from the surface of the
case. Refer to Figure 2
8. If removed for inspection, reinstall actuators support on the transmission with new
nuts and washers in accordance with instructions in BHT-222-CR&0-2, Chapter
63. Reinstall all parts previously removed in accordance with BHT-222U-MM-6,
Chapter 63.
9. Reinstall fairings and cowlings previously removed. Refer to BHT-222U-MM-9,
Chapter 71.
10. Annotate helicopter records to reflect compliance with this bulletin.

### Page 5 (OCR)

222U-00-57
Page 5 of 6
0.5008 - 0.5013 IN Dia.  0.5008 - 0.5013 IN Dia.
(12.72 - 12.73 mm)  0.3758 - 0.3763 IN Dia.  (12.72 - 12.73 mm)
(9.54 - 9.55 mm)
0.265 - 0.272 IN Dia.
(6.73 - 6.90 mm)
0.343 - 0.350 IN Dia.
(8.71 - 8.89 mm)
Hydraulic Actuator  ILL 00101
Support Assembly
P/N 222-040-125-001
Figure 1

### Page 6

(No text on this page.)

### Page 7 (OCR)

222U-00-57
Page 6 of 6
DOWEL PINS
Transmission Top Case Assembly
P/N 222-040-061-101 through 105
Figure 2
• ILL00102

### Page 8

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
