# Bell Service Bulletin 407-23-129RA: Revision A

- Rights: © Bell Textron Inc. Filed by the FAA in regulations.gov docket FAA-2026-0736, the docket of AD 2026-10-04. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Bell Service Bulletin 407-23-129RA](https://openairdocs.org/service-documents/bell/407-23-129ra.md)
- Title as filed: Bell ASB 407-23-129 Rev A
- Pages: 15
- PDF: https://openairdocs.org/files/sha256/b3/31/b331bc9c4594c581c2601eda3b78f138c0394c74864914492f29db81627d42a4
- Page: https://openairdocs.org/service-documents/bell/407-23-129ra/file/b331bc9c4594

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ASB 407-23-129RA 
Page 1 of 15 
Approved for public release. 
 
 
  ALERT SERVICE BULLETIN 407-23-129 
29 June 2023 
Revision A, 30 October 2023 
 
 
MODEL AFFECTED:  407 
 
SUBJECT: ELECTRICAL HARNESSES, INSPECTION OF 
 
HELICOPTERS AFFECTED: S erial number s 54300 through 54752, 54805 
through 54999, and 56300 through 56366 and 
56368. 
 
 [Serial number 56367 and 56369 and subsequent will 
have the intent of this bulletin accomplished prior to 
delivery.] 
 
COMPLIANCE: Within the next 100 flight hours or 90 days, whichever 
occurs first, following the release date of Revision A of 
this bulletin. 
 
DESCRIPTION: 
 
Bell has become aware of the possibility for an electrical harness  to chafe at various 
locations in the aircraft instrument panel area. Chafing may occur between the Primary 
Flight Display (PFD)/Multi-Function Display ( MFD) harnesses and the Cable Harness 
Protection System (CHiPS) rack, and between the electrical harnesses and the shroud 
behind the instrument panel area. 
 
This Alert Service B ulletin (ASB) mandates a one-time inspection of the electrical 
harnesses in the instrument panel area and provides instructions to improve the 
electrical harnesses protection adding sleeving protection, by r otating the lower GEA  
connector backshell by 180 degrees and adding an additional clamp. 
 
Revision A  of this bulletin provides instructions to r otate the Primary Flight Display 
(PFD) and Multi -Function Display (MFD) connector backshell s ( 3160DS2P1 and 
3160DS1P1) cast housing 180 degrees as well as clarifying the rotation of the G EA 
connector backshell.

### Page 2

ASB 407-23-129RA 
Page 2 of 15 
Approved for public release. 
An alternate fastener has been added for the installation of the support (160- 027-460) 
and the sleeving part number in the Required Material section of this bulletin has been 
corrected. 
It also provides guidance to address potential chafing conditions when kits or 
customizing have been added to the helicopter preventing fully accomplishing the 
requirements of this bulletin. 
 
Owners/operators having accomplished the intent of the original release of this bulletin 
are required to accomplish the changes introduced in this Revision A. 
 
Applicability of this bulletin to any spare part shall be determined prior to its installation 
on an affected helicopter. 
 
APPROVAL: 
 
The engineering design aspects of this bulletin are Transport Canada Civil Aviation 
(TCCA) approved. 
 
 
CONTACT INFO: 
 
For any questions regarding this bulletin, please contact: 
 
Bell Product Support Engineering 
Tel: 1-450-437-2862 / 1-800-363-8023 / productsupport@bellflight.com 
 
 
MANPOWER: 
 
Approximately 8 man-hours are required to complete this bulletin. This estimate is 
based on hands-on time and may vary with personnel and facilities available. 
 
 
WARRANTY: 
 
There is no warranty credit applicable for parts or labor associated with this bulletin. 
 
 
MATERIAL: 
 
Required Material: 
 
The following material is required for the accomplishment of this bulletin and may be 
obtained through your Bell Supply Center. The kit part number CA-407-23-129 contains 
the parts listed below; however, they are available in limited quantity, but the parts can 
be ordered individually.

### Page 3

ASB 407-23-129RA 
Page 3 of 15 
Approved for public release. 
For serial numbers 54300 through 54696, part number 2640- 00104-00 sleeving will 
need to be ordered in addition with the kit CA-407-23-129 to perform this ASB. 
 
Part Number Nomenclature Qty (Note) 
   
   
90-002-3 SELF-LOCKING NUT RIGHT 
ANGLE BRACKET 
1 
NAS1097AD4-4 
NAS9303B-4 
RIVET 
RIVET (alternate) 
2 
2(3) 
NAS1801-3-13 SCREW 1 
NAS1149D0332J WASHER 2 
160-027-460 SUPPORT 1 
NAS43DD3-20N SPACER 1 
2640-00104-00 SLEEVING 4feet/1.2m (1)(2) 
 
NOTES: 
 
1. Not included in CA- 407-23-129 kit. Only required for helicopters serial numbers 
54300 through 54696. 
2. Sleeving is sold by linear foot. Quantity required must be specified in the order. 
3. Blind rivet alternate for rivet NAS1097AD4-4. 
 
Consumable Material: 
 
The following material is required to accomplish this bulletin, but may not require 
ordering, depending on the operator’s consumable material stock levels.  This material 
may be obtained through your Bell Supply Center. 
 
 
Part Number Nomenclature Qty (Note) Reference * 
    
PLT2S-C702Y Cable Tie AR C-292 
 
* C-XXX numbers refer to the consumables list in the BHT-ALL-SPM, Standard Practices Manual 
 
SPECIAL TOOLS: 
 
None required. 
 
WEIGHT AND BALANCE: 
 
Not affected 
 
ELECTRICAL LOAD DATA: 
 
Not affected.

### Page 4

ASB 407-23-129RA 
Page 4 of 15 
Approved for public release. 
REFERENCES: 
 
407-IPB Illustrated Parts Breakdown 
407-MM Maintenance Manual 
BHT-ELEC-SPM - Electrical Standard Practices Manual 
BHT-SRM-ALL – Structural Repair Manual 
CSSD-PSE-90-001 - Chafing Control Guide 
 
PUBLICATIONS AFFECTED: 
 
407-IPB Illustrated Parts Breakdown 
 
ACCOMPLISHMENT INSTRUCTIONS: 
 
-NOTE- 
 
Installation of additional kits or customizing may require  
different routing of the harnesses which may prevent 
accomplishment of all the requirements of this ASB . In such 
cases, owners/operators should refer to the Chafing Control 
Guide (CSSD-PSE-90-001) and Electrical Standard Practice 
Manual (BHT -ELEC-SPM) to  prevent any potential chafing 
conditions. 
If chafing prevention has been incorporated but are slightly 
different from the requirements of this ASB, they are 
considered as meeting the intent of this bulletin. This does not 
apply to the installation of the sleeving (2640-00104-00) which 
is considered a mandatory requirement. 
 
1. Prepare the helicopter for maintenance. 
2. Make sure all electrical power is removed from helicopter. 
WARNING 
 
OBEY ALL THE SAFETY PRECAUTIONS WHEN YOU DO 
MAINTENANCE ON OR NEAR ELECTRICAL/ELECTRONIC 
EQUIPMENT (DMC-407-A-96-00-00-00A-012A-A). 
 
3. Remove the Primary Flight Display (PFD) and Multi-Function Display (MFD) (DMC-
407-A-95-13-05-00A-520A-A). 
4. Remove the Engine Airframe Unit (GEA) (DMC-407-A-95-64-04-00A-520A-A).

### Page 5

ASB 407-23-129RA 
Page 5 of 15 
Approved for public release. 
5. Gain access to the electrical harnesses in instrument panel area by r emoving the 
right lower and upper console panel followed by the left upper, right upper, and right 
lower shroud assembly. (DMC-407-A-95-13-03-00A-520A-A). 
6. Do a detailed visual i nspection of the electrical harnesses behind the instrument 
panel area for any chafing. Pay attention to the electrical harnesses  at the Cable 
Harness Protection System (CHiPS) rack and around shroud area. 
7. Repair damaged wires/bundles and identify/address the source of the chafing. Refer 
to Electrical Standard Practices Manual (BHT -ELEC-SPM) and Chafing Control 
Guide (CSSD-PSE-90-001) for additional information. 
 
-NOTE- 
 
The sleeve (2640-00104-00) length shall fully cover the wire 
bundle in the flexible chain link conduit of the CHiPS rack. 
 
8. For helicopters serial numbers 54300 through 54696 without sleeve installed on the 
wire bundle in the flexible chain link conduit of CHiPS rack , cut the sleeve to the 
correct length and install it to cover the wire bundle into the flexible chain link conduit 
for both CHiPS rack (BHT-ELEC-SPM). 
CAUTION 
 
Disconnect the Configuration Module before rotating the GEA 
backshell housing. 
-NOTE- 
 
Helicopters serial number 5 6358 and subsequent have the 
lower GEA connector backshell rotated. 
 
9. R otate the lower GEA connector (7320A1P1) backshell cast housing by 180 
degrees. The shield block and grounding screw heads should face left hand side of 
helicopter after rotation (Figure 2). 
-NOTE- 
 
The GEA connector (7320A1P1) on helicopter serial numbers 
54300 through 54566 and 54568 through 54804 has  a 
configuration module in the backshell cast housing. 
 
10. For GEA connectors without the configuration module, perform  steps 17 a, c, d, e, 
and g to rotate the connector backshell of the GEA.

### Page 6

ASB 407-23-129RA 
Page 6 of 15 
Approved for public release. 
11. For GEA connectors with a configuration module, perform steps 1 7 a through g to 
rotate the connector backshell of the GEA. 
 
-NOTE- 
 
Install the rivets with manufactured head on the bottom side 
of support 407 -031-202-119. Helicopters serial 5 6358 and 
subsequent have the support installed.  
 
12.  Drill two rivet holes on support 407- 031-202-119 (Figure 1) using No.30 drill bit. 
Countersink and deburr each hole and install the self-locking nut right angle bracket 
(1) with rivets (2) (BHT-SRM-ALL). 
13.  Install the support (3) and spacer (4) with screw (5) and washers (6). 
14.  Secure the wire harness W101 (7) with cable tie on the support (3). 
15. Install the left upper, right upper and right lower shroud assembly followed by the 
right upper and lower console panel (DMC-407-A-95-13-03-00A-720A-A). 
16.  Install the GEA unit (DMC-407-A-95-64-04-00A-720A-A). 
 
CAUTION 
 
Disconnect the Configuration Module before rotating the PFD 
backshell housing. 
 
17. To prevent fretting of the grounding screw  heads against the Chips rack, the 
backshell cast housing of the PFD connector (3160DS 2P1) and MFD connector 
(3160DS1P1) backshells must be rotated 180 degrees.  The shield block and 
grounding screw heads should face on the left hand side of helicopter after r otation 
(Figure 3) . Rotate the PFD connector (3160DS2P1) backshell cast housing as 
follows: (Figure 3). 
-NOTE- 
 
Helicopters serial numbers 5 6337 through 56366 and 56368 
may already have the PFD and MFD connector backshells 
rotated. Confirm the orientation of the grounding screw heads. 
If the grounding screw heads are facing on the left hand side 
of the helicopter, go to step 19.

### Page 7

ASB 407-23-129RA 
Page 7 of 15 
Approved for public release. 
a. Remove screws (2) from lid (1) and set aside. 
b. Carefully remove connector (4) from the Configuration Module (5). Pay particular 
attention when handling the 4-Conductor Harness (3). 
c. Remove the screws (7) securing the strain relief (6) and set aside. 
 
d. Carefully rotate the backshell cast housing (9) 180 degrees. The grounding 
screws on the shield block (8) should face on the left hand side of helicopter after 
rotation. 
e. Re-position the connector (10) onto the backshell cast housing (9) and install the 
strain relief (6) and screws (7). 
 
f. Carefully insert the connector (4) into the Configuration Module (5). 
g. Install the lid (1) with screws (2). 
 
-NOTE- 
 
The MFD connector (3160DS1P1) does not have a  
Configuration Module. 
 
18. Rotate the MFD connector (3160DS1P1) backshell cast housing by 180 degrees as 
per steps 17 a, c, d, e, and g. The shield block and grounding screw heads should 
face left hand side of helicopter after rotation (Figure 3). 
19. Install the PFD and MFD (DMC-407-A-95-13-05-00A-720A-A). 
20. Make an entry in the helicopter logbook and historical service records indicating 
compliance with this Alert Service Bulletin.

### Page 8 (OCR)

LOOKING INBOARD LEFT SIDE
RBL  0.30 IN.
(2 PLACES)  15.88  REF  (7.6 mm)  TRUE
407-031-202-119 REF
6.0 IN. (152 mm)  STA
30.15
REF
(2 PLACES)
VIEW A
LOOKING DOWN ON NORMAL TO SUPPORT
1. Self-Locking Nut, Right Angle Bracket (90-002-3)
2. Rivet (NAS1097AD4-4) / Rivet, Blind (Alternate, NAS9303B-4)
3. Support (160-027-460)
4. Spacer (NAS43DD3-20N)
5. Screw (NAS1801-3-13)
6. Washer (NAS1149D0332J)
7. Wire Harness W101 (Ref)
Figure 1 - Clamp Installation (Page 1 of 2)
ASB 407-23-129RA
Page 8 of 15
Approved for public release.

### Page 9

ASB 407-23-129RA 
Page 9 of 15 
Approved for public release. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 1 – Clamp Installation (Page 2 of 2)

### Page 10

ASB 407-23-129RA 
Page 10 of 15 
Approved for public release. 
 
 
 
 
 
 
 
 
Figure 2 (Sheet 1 of 3) – GEA backshell rotation 
Pre-Rotation of Connector Backshell

### Page 11

ASB 407-23-129RA 
Page 11 of 15 
Approved for public release. 
 
 
 
 
 
 
 
 
Figure 2 (Sheet 2 of 3) – GEA backshell rotation 
Post-Rotation of Connector Backshell

### Page 12 (OCR)

7Z88
Figure 2 (Sheet 3 of 3) - Example of GEA and MFD Connector (Lid Removed)
(GEA Connector shown)
ASB 407-23-129RA
Page 12 of 15
Approved for public release.

### Page 13 (OCR)

23536_001a
Figure 3 (Sheet 1 of 2) - PFD Connector 3160DS2P1
(Exploded View - Additional wiring removed for clarity)
Pre-Rotation of Connector Backshell
ASB 407-23-129RA
Page 13 of 15
Approved for public release.

### Page 14 (OCR)

1. Lid
2. Screw (Qty 2)
3. Cable, 4-Conductor harness
4. Connector
5. Configuration module
6. Strain relief
7. Screw (Qty 3)
8. Shield block
9. Cast housing
10. Connector
23536_001b
Figure 3 (Sheet 2 of 2) - PFD Connector 3160DS2P1
(Exploded View - Additional wiring removed for clarity)
Post-Rotation of Connector Backshell
ASB 407-23-129RA
Page 14 of 15
Approved for public release.

### Page 15

ASB 407-23-129RA 
Page 15 of 15 
Approved for public release. 
     
 
 
 
 
Figure 4 – Pre and Post PFD and MFD Connector Backshell Rotation 
Pre-rotation of 
connector backshell 
Post-rotation of 
connector backshell

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
