# Bell Service Bulletin 407-23-130RA: Revision A

- Rights: © Bell Textron Inc. Filed by the FAA in regulations.gov docket FAA-2025-3436, the docket of AD 2026-14-07. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Bell Service Bulletin 407-23-130RA](https://openairdocs.org/service-documents/bell/407-23-130ra.md)
- Title as filed: Bell ASB 407-23-130 Rev A
- Pages: 16
- PDF: https://openairdocs.org/files/sha256/2b/d1/2bd12bb5e2411011c647a34288319a6d05528edcb759bccefe12d3f99c6116f8
- Page: https://openairdocs.org/service-documents/bell/407-23-130ra/file/2bd12bb5e241

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ASB 407-23-130RA 
Page 1 of 16 
Approved for public release. 
 
 
  ALERT SERVICE BULLETIN 407-23-130 
27 February 2023 
Revision A, 27 March 2023 
 
 
 
MODEL AFFECTED:  407 
 
SUBJECT: PILOT CYCLIC STICK ASSEMBLY 206 -001-344-
105/-109/-115, INSPECTION AND REPAIR OF. 
 
HELICOPTERS AFFECTED: S erial number s 53000 through 53900, 53911 
through 53999, 54000 through 54166, 54300 
through 54 800, 54 805 through 54 999, 56300 
through 56304, 56311 through 56315. 
 
Serial number 54955, 54998, 56305 through 56310, 
and 56316  and subsequent are not affected by  this 
bulletin. 
 
COMPLIANCE: PART I: Within 100 flight hours or 90 days, whichever 
occurs first, following the release date of this bulletin. 
 
PART II: Prior to next flight as required by PART I. 
 
PART III:  Within 300 flight hours or 6 months, 
whichever occurs first, after accomplishment of PART 
II, and every 300 flight hours or 6 months thereafter 
until accomplishment of PART IV. 
 
PART IV: Within 24 months after accomplishment of 
PART II. 
 
DESCRIPTION: 
 
Bell has recently received a report of a fractured pilot cyclic stick found while performing 
the Interior and Prestart Check of the 407 Rotorcraft Flight Manual (RFM).  The fracture 
originated at the upper slotted area near the lower base of the cyclic stick.

### Page 2

ASB 407-23-130RA 
Page 2 of 16 
Approved for public release. 
Consequently, helicopters of a mixed fleet were inspected, and additional cyclic sticks 
were found cracked on 407 helicopters. 
 
The cracked cyclic sticks may have resulted from excessive force being applied when 
checking the travel of the cyclic stick to verify the cyclic centering light operation. 
 
As a result, the Interior and Prestart Check of the applicable Flight Manuals was revised 
to limit the freedom of movement of the cyclic stick to approximately 1 inch (25.4 mm) 
when the CYCLIC CENTERING light is verified.  
 
PART I of this bulletin mandates a  10X magnifying glass inspection of the lower four 
inches of the cyclic stick tube assembly (1, Figure 1). 
 
PART II of this bulletin provides a repair for cracked 206-001-342-101 cyclic stick tube 
assemblies consisting of a stop drill procedure. This repair can only be performed for 
cracks initiating in the upper slot on the lower part of the stick tube. The maximum 
repairable crack length is shown in Figure 2 of this bulletin. 
 
PART III of this bulletin introduces a 300 flight hour or 6 month, whichever occurs first, 
10X magnifying glass visual inspection of the cyclic stick tubes that have been repaired 
per PART II. This inspection is a recurring inspection until accomplishment of PART IV. 
 
PART IV of this bulletin mandates the replacement of the repaired cyclic stick tube 206-
001-342-101FM accomplished in PART II. 
 
Revision A of this bulletin requires customers to contact Bell Product Support when 
finding a cracked cyclic stick tube assembly. Figures with drill bushings revised to allow 
a final ream of .1875-inch (4.763mm). 
 
Applicability of this bulletin to any spare part must be determined prior to its installation 
on an affected helicopter. 
 
APPROVAL: 
 
The engineering design aspects of this bulletin are Transport Canada Civil Aviation 
(TCCA) approved. 
 
CONTACT INFO: 
 
For any questions regarding this bulletin, please contact: 
 
Bell Product Support Engineering 
Tel: 1-450-437-2862 / 1-800-363-8023 / productsupport@bellflight.com

### Page 3

ASB 407-23-130RA 
Page 3 of 16 
Approved for public release. 
MANPOWER: 
 
Approximately 4.0 man-hours are required to complete PART I of this bulletin.  
Approximately 6.0 man-hours are required to complete PART II of this bulletin.   
Approximately 2.0 man-hours are required to complete PART III of this bulletin. 
Approximately 2.0 man-hours are required to complete PART IV of this bulletin. 
 
This estimate i s based on hands-on time and may vary with personnel and facilities 
available. 
 
WARRANTY: 
 
There is no warranty credit applicable for parts or labor associated with this bulletin. 
 
MATERIAL: 
 
Required Material: 
 
The following material is required for the accomplishment of this bulletin and may be 
obtained through your Bell Supply Center. 
 
Part Number Nomenclature Qty (Note) 
   
206-001-342-101 Cyclic Stick Tube Assy 1 (1) 
 
NOTE 1: Only required if the cyclic stick tube exceeds the mechanical and/or corrosion 
damage limits of PART I. 
 
Consumable Material: 
 
The following material is required to accomplish this bulletin, but may not require 
ordering, depending on the operator’s consumable material stock levels.  This material 
may be obtained through your Bell Supply Center. 
 
Part Number Nomenclature Qty (Note) Reference * 
    
2230-00425-00 Primer, Epoxy 1 PT (1) C-204 
2230-06023-00 Polyamide Coating, Polyurethane 5 QT (1) C-245 
2100-00006-00 Cleaning Compound 5 GAL (1) C-318 
2900-05806-00 Aluminum oxide abrasive cloth or 
paper (400 grit) 
A/R C-406 
2230-05688-00 Paint Remover 1 PT (1) C-436 
 
* C-XXX numbers refer to the consumables list in the BHT-ALL-SPM, Standard Practices Manual

### Page 4

ASB 407-23-130RA 
Page 4 of 16 
Approved for public release. 
NOTE 1: The quantity indicated is the format the product is delivered in. Actual quantity 
required to accomplish the instructions in this bulletin may be less. 
 
SPECIAL TOOLS: 
 
Locally manufactured drill guide (Figure 4). 
Drill bushings for drill guide - may be procured locally or through McMaster-Carr 
or Carr-Lane. 
 
WEIGHT AND BALANCE: 
 
Not affected. 
 
ELECTRICAL LOAD DATA: 
 
Not affected. 
 
REFERENCES: 
 
BHT-407-MM Maintenance Manual, Chapter 5 and 67 
BHT-ALL-SPM Standard Practices Manual, Chapter 4 and 6 
BHT-ELEC-SPM Electrical Standard Practices Manual, Chapter 5 
BHT-407-FM-1, 22 SEP 2022 Rev. 22 
BHT-407-FM-2, 22 SEP 2022 Rev. 17 
BHT-407-FM-3, 22 SEP 2022 Rev. 9 
 
PUBLICATIONS AFFECTED: 
 
BHT-407-IPB Illustrated Parts Breakdown, Chapter 67 
BHT-407-MM Maintenance Manual, Chapter 5 and 67 
 
ACCOMPLISHMENT INSTRUCTIONS: 
 
PART I: 206-001-342-101 Cyclic Stick Tube Inspection 
 
-NOTE- 
 
The cyclic stick tubes 206 -001-342-101 are currently on 
manual allocation due to limited quantities available. 
 
1. Prepare the helicopter for maintenance.

### Page 5

ASB 407-23-130RA 
Page 5 of 16 
Approved for public release. 
-NOTE- 
 
Clean the lower 4.0 inches (101.6 mm) of the removed cyclic 
stick assembly with cleaning compound (C -318) before 
inspection (1, Figure 1). 
 
2. Perform the Pilot Cyclic Control Stick  1200 Hour or 24 Month Inspection (DMC-407-
A-67-12-03-00A-281A-A). 
a. If no crack is found, go to step 4. 
b. If a crack is fo und or suspected using the 10X magnifying glass visual 
inspection, disassemble the cyclic stick assembly by removing the cyclic stick 
grip assembly. 
i. Disconnect the wires from connector (BHT -ELEC-SPM, Chapter 5) ; 
retain connector for further use (9, Figure 1). 
 
ii. Remove screw (5), washers (6) and nut (7). 
iii. Remove cyclic stick grip (4) and elbow (8) as an assembly from cyclic 
control stick (1). 
-NOTE- 
 
Applying heat to the stick tube (1, Figure 1)  after removal of 
screw (5) may be required if the cyclic stick grip and elbow 
assembly (8) is difficult to remove.  Pay particular attention to 
direct heat away for the cyclic stick grip (4).  Do not exceed 
200°F (93°C). 
 
CAUTION 
 
When the cyclic stick grip assembly is being removed, ensure 
that the wire removal is assisted f rom the connector end to 
avoid excessive stress on the cyclic stick grip connections. 
 
c. R emove the paint and primer with paint remover (C -436) and thoroughly 
inspect the lower end of the cyclic stick tube using the fluorescent penetrant 
inspection (FPI) method (BHT-ALL-SPM, Chapter 6). 
d. If cracks are found, accomplish PART II  prior to next flight or replace the 
cracked cyclic stick tube assembly with a serviceable part meeting the intent 
of the bulletin.

### Page 6

ASB 407-23-130RA 
Page 6 of 16 
Approved for public release. 
i. The following inspection criteria apply to a cracked cyclic tube stick 
assembly eligible for the accomplishment of PART II: 
1. Cracks that  extend beyond the edges of the slot  are not 
permitted (Figure 2). 
2. C racked slot lengths longer than 0.791 inch (20.09 mm) are not 
permitted. 
ii. If the crack length in the cyclic stick assembly exceeds the criteria of 
step 2.d.(i), the cyclic stick tube assembly will be considered 
unserviceable and must be replaced by a serviceable cyclic stick tube 
assembly meeting the intent of this bulletin prior to next flight. 
3. Customers finding a cracked cyclic stick tube  assembly must send an email to Bell 
Product Support Engineering at productsupport@bellflight.com  with the following 
information. 
a. Subject Line: Helicopter model, serial number and ASB number. 
Example email subject line: 
 
407 (53001) – ASB 407-23-130RA 
 
b. The email shall include the following information: 
(1) Total time in-service. 
(2) Cyclic stick tube part number. Ex: 206-001-342-101. 
(3) Clear in-focus pictures of the damaged cyclic stick tube assembly. 
4. If no cracks are found, thoroughly clean the cyclic stick tube with water and mild 
detergent (C-318) to completely remove residual penetrant and developer.  
a. Dry the cyclic stick assembly completely. 
b. Restore removed primer (C-204) and organic finish with polyurethane coating 
(C-245) before installation of stick into pivot assembly ( BHT-ALL-SPM, 
Chapter 4). 
5. If the cyclic stick assembly was disassembled, reinstall cyclic stick grip and wiring 
harness as follows:

### Page 7

ASB 407-23-130RA 
Page 7 of 16 
Approved for public release. 
a. R oute the wires through the tube assembly (1, Figure 1). 
b. I nstall the cyclic stick grip (4) and elbow (8) as an assembly. 
c. S ecure the elbow (8) into the cyclic stick tube (1) with screw (5), washers (6) 
and nut (7). 
d. I nsert wires in connector (9) (BHT-ELEC-SPM Chapter 5). 
6. Install the pilot cyclic control stick assembly (DMC-407-A-67-12-03-00A-720A-A). 
7. Ensure the following revisions of the INTERIOR AND PRESTART CHECK are 
inserted in the applicable Flight Manual (RFM): 
a. BHT-407-FM-1, 22 SEP 2022 Rev. 22 
b. BHT-407-FM-2, 22 SEP 2022 Rev. 17 
c. BHT-407-FM-3, 22 SEP 2022 Rev. 9 
8. Make an entry in the helicopter logbook and historical service records indicating 
compliance with PART I of this Alert Service Bulletin. 
PART II: Pilot cyclic stick assembly stop-drill repair 
 
1. For cyclic stick tubes with cracks in the slotted area not exceeding the limits of Figure 
2, carry out the following stop drill procedure: 
-NOTE- 
 
The maximum repairable crack length that can be stop drilled 
cannot be beyond the outside edge of the slot (Figure 2). The 
pilot hole for the stop drill must be in the full thickness of the 
tube, centered along the centerline of the slot and no further 
than 0.010 inch (.25 mm) from the edge of the slot (Figure 3 , 
Sheet 1 of 2). 
 
a. Use an automatic center punch to mark the edge of the slot (Figure 3, Sheet 1 of 
2).

### Page 8

ASB 407-23-130RA 
Page 8 of 16 
Approved for public release. 
CAUTION 
 
The location and orientation of the stop drill is critical . It is 
important to properly secure the cyclic stick tube prior to 
drilling to ensure the drill bit is oriented exactly through the 
centerline of the tube. Preferably the cyclic stick tube should 
be held in place in a fixing head and drilled on a milling 
machine. However, since this is not always achievable, Figure 
4 shows an example of a drill guide that can be locally 
manufactured to ensure a clean and well -oriented stop drill 
hole. Figure 5 shows the installed workaid with the addition of 
various drill bushings for precise drilling and reaming. 
 
b. Locally manufacture a workaid (Figure 4) and procure drill bushings or have the 
cyclic stick tube stop-drilled in a milling machine. 
c. Install the drill guide on the cyclic stick tube (Figure 5) and line up with the center 
punch mark using the smallest drill bushing. 
d. Secure the drill guide by tightening the nuts only enough to stop the drill guide 
from moving. Confirm that the drill bushing hole is exactly in line with the center 
punch mark. Do not over-tighten nuts and bolts to avoid damaging the cyclic stick 
tube. 
e. Drill a pilot hole using the smallest drill guide. Use a drill stop to limit the drilling 
depth to avoid damaging the opposite side of the tube. 
-NOTE- 
 
Stop drill holes must be free of all sharp edges and deburred.  
 
f. Increase the stop drill hole diameter until a final ream of 0.1875  inch (4.76 mm) 
is achieved. Deburr holes. 
g. Once the  stop drill procedure is completed , carry out a fluorescent penetrant 
inspection (FPI) of the repaired area to ensure the crack is removed and there 
are no cracks in the stop drill bore. (BHT-ALL-SPM, Chapter 6). 
h. Thoroughly clean the cyclic stick tube with water and mild detergent (C -318) to 
completely remove residual penetrant and developer. 
i. D ry the cyclic stick assembly completely. 
j. Touch up the repaired area with epoxy polyamide primer (C -204). Refinish the 
repair as required to match the original finish with polyurethane coating (C -245) 
(BHT-ALL-SPM, Chapter 4).

### Page 9

ASB 407-23-130RA 
Page 9 of 16 
Approved for public release. 
2. The repaired cyclic stick tube assembly must be identified as follows: 
a. I dentify the lower part of the cyclic stick tube directly above the pivot assembly 
by hand marking or stencil marking part number 206-001-342-101FM with white 
or silver lettering. The size of the alpha-numeric lettering must be approximately 
0.25 inch (6.35 mm) -in height. 
3. Reinstall cyclic stick grip and wiring harness as follows: 
i. Route the wires through the tube assembly (1, Figure 1). 
ii. Install the cyclic stick grip (4) and elbow (8) as an assembly. 
iii. Secure the elbow (8) into the cyclic stick tube (1) with screw (5), 
washers (6) and nut (7). 
4. I nstall the pilot cyclic control stick assembly (DMC-407-A-67-12-03-00A-720A-A). 
5. Inse rt wires in connector (9, Figure 1) using Insert/Extract Tool M81969/14- 10 and 
reinstall connector (9). 
6. PART III and PART IV of this bulletin are mandatory after completing PART II. 
7. Make an entry in the helicopter logbook and historical service records ind icating 
compliance with PART II of this Alert Service Bulletin. 
PART III: Recurring inspection of cyclic stick tubes 206-001-342-101FM 
 
1. Prepare the helicopter for maintenance. 
2. Remove the pilot cyclic control stick (DMC-407-A-67-12-03-00A-520A-A). 
3. Clean the lower 4.0 inches (101.6 mm) of the removed cyclic stick assembly ( 1, 
Figure 1) with cleaning compound (C-318) before inspection. 
4. I nspect the lower 4.0 inches (101.6 mm) of the cyclic stick tube using a 10X magnifying 
glass. Pay particular attention to the stop-drilled repair area. 
-NOTE- 
 
Cracks in the circled areas of the inner  sleeve inboard of the 
stop-drilled holes as shown in Figure 3 (Sheet 2 of 2)  are not 
cause for rejection.

### Page 10

ASB 407-23-130RA 
Page 10 of 16 
Approved for public release. 
a. If any cracks are found, remove the cyclic stick tube assembly from service and 
replace with a serviceable cyclic stick tube assembly meeting the intent of this 
bulletin. 
b. If no cracks are found, install the cyclic control stick assembly (DMC-407-A-67-
12-03-00A-720A-A). 
5. Make an entry in the helicopter logbook and historical service records indicating 
compliance with PART III of this Alert Service Bulletin. 
6. Repeat PART III every 300 flight hours or 6 months, whichever occurs first, until 
accomplishment of PART IV. 
PART IV: Replacement of the cyclic stick tube 206-001-342-101FM 
 
1. Prepare the helicopter for maintenance. 
2. Remove the cyclic stick tube  assembly 206-001-342-101FM that was repaired per 
PART II of this bulletin. 
3. Install a serviceable 206 -001-342-101 cyclic stick tube  assembly (DMC-407-A-67-
12-03-00A-720A-A). 
4. Make an entry in the helicopter logbook and historical service records indicating 
compliance with PART IV of this Alert Service Bulletin.

### Page 11 (OCR)

DETAIL A
1. Cyclic control stick
2. Pivot assembly bore
3. Pivot assembly
4.00 IN.  4. Grip assembly
(101.6 mm)  5.  Screw
6. Washer
7. Nut
8. Elbow
9. Connector
AREA TO BE
INSPECTED
(9)
SEE DETAIL A
22568_002
Figure 1 - Pilot Cyclic Stick Assembly - 10X Magnifying Glass Inspection Area
_ ASB 407-23-130RA
Page 11 of 16
Approved for public release.

### Page 12 (OCR)

206-001-342-101
CYCLIC STICK TUBE
MAXIMUM REPAIRABLE  IF SLOT LENGTH IS GREATER THAN
CRACK - MAY NOT GO  • 791 .791 (20.09 mm), CYCLIC STICK MAY
PAST EDGE OF SLOT  NOT BE REPAIRED BY STOP DRILLING.
DETAIL C
Figure 2- Typical Crack Location and Maximum Repairable Crack Length
ASB 407-23-130RA
Page 12 of 16
Approved for public release.

### Page 13 (OCR)

TYPICAL CRACK
LOCATIONS
SLOT CLY
MAXIMUM REPAIRABLE
CRACK - MAY NOT GO
PAST EDGE OF SLOT
E  CYCLIC STICK AFTER
STOP DRILLING WITH
Ø .1875" HOLES
(Ø 4.763 mm)
STOP DRILL POSITION
WITH #50 HOLE (.0700")(1.778 mm)
SLOT CL
. 010  MAX. DISTANCE OF DRILL
(0.254mm) CENTER FROM SLOT EDGE
DETAIL E
Figure 3 (Sheet 1 of 2) - Pilot Hole Location for Stop Drill
ASB 407-23-130RA
Page 13 of 16
Approved for public release.

### Page 14 (OCR)

Cracks ends stop drilled
0.188 IN. (4.76 mm)
Holes
UP
SEE DETAIL A
DETAIL A
NOTE
1 Cracks in the circled areas of the inner sleeve inboard of the stop-drilled holes are not cause for rejection.
22568_003
Figure 3 (Sheet 2 of 2) - Stop-Drilled Holes and Inner Sleeve
ASB 407-23-130RA
• Page 14 of 16
Approved for public release.

### Page 15 (OCR)

-Ø :3125  -Ø:260 2 PL
(7.976 to 7.938 mm)  (6.86 to 6.60 mm)
CARR LANE DRILL BUSHINGS
OR EQUIVALENT:
(1) SF-20-12-.0700
. 03 × 45' CHAMF TYP  (9.53 mm)  (19.1 mm)
/ (0.8 mm X 45")  . 527 (13.39 mm)  (1) SF-20-12-.128:
(1) SF-20-12-.1719
(1) SF-20-12-.1875
- (2) AN350-4 WING NUTS
.400 REF  OR COOIVALEN
(35.56 mm)
(33.96 mm)
(2) NAS1149F0463P
OR EQUIVALENT
Ø 1.235 REF
TUBE O.D.
(Ø 31.37 mm)
• 1.190  • 1.190-  . 37
(9.4 mm)  (30.23 mm)  (30.23 mm )  (9.4 mm)  • UPPER V-BLOCK
3.13
(79.5 mm)
SECTION A-A
SCALE 2:1
UPPER V-BLOCK
SCALE 2:1
- LOWER V-BLOCK
SECTION B-B
SCALE: 2/1  (2) NAS66D4D4  OR EQUIVALEN
LOWER V-BLOCK
SCALE 2:1
SAME AS UPPER V-BLOCK  STOP DRILL SHOP AID ASSEMBLY
EXCEPT .3125 (7.938 mm)  EXPLODED DIAGRAM
CENTER HOLE MAY BE OMITTED  SCALE 2:1
NOTES:
1. ALL DIMENSIONS IN INCHES. MILLIMETERS IN PARENTHESES.
2. V-BLOCK MATERIAL IS OPTIONAL. METALS, PLASTICS, OR 3D PRINTED PLASTICS ARE ACCEPTABLE.
3. BREAK ALL SHARP EDGES WITH .015 (0.38 mm) RADIUS OR .015 (0.38 mm) × 40-50 DEGREE CHAMFER.
4. TOLERANCES ON DECIMALS (INCHES):
XXX +.010 (0.25 mm)
XX ‡.03 (0.8 mm)
X +.1 (3 mm)
TOLERANCE ON ANGLES +1/2°
5. LOCK SCREW (NOT SHOWN) TO SECURE BUSHING IS OPTIONAL.
23503_002
Figure 4 - Drilling Guide V-Blocks (Workaid)
ASB 407-23-130RA
Page 15 of 16
Approved for public release.

### Page 16 (OCR)

CYCLIC STICK TUBE
STOP DRILL
WORK AID
STOP DRILL SHOP AID
POSITIONED ON CYCLIC STICK  FT
G
H
SECTION D-D .0700-  SECTION F-F .098-  SECTION G-G .1285-  SECTION H-H
(1.778 mm)  (2.49 mm)  (3.264 mm)  DRILL TO .1719 (4.366 mm)
REAM TO .1875 (4.763 mm)
Figure 5 - Cyclic Stick Tube with Workaid Installed
ASB 407-23-130RA
Page 16 of 16
Approved for public release.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
