# Bell Alert Service Bulletin 206-06-110: No revision named

- Rights: © Bell Textron Inc. Filed by the FAA in regulations.gov docket FAA-2008-0040; AD 2008-14-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Bell Alert Service Bulletin 206-06-110](https://openairdocs.org/service-documents/bell/sb-206-06-110.md)
- Title as filed: U.S. DOT/FAA - Bell ASB 206-06-110
- Pages: 6
- PDF: https://openairdocs.org/files/sha256/2a/c8/2ac864dcffde2941af2a92553e2290896b1506193353e523da1a65a416a1bf81
- Page: https://openairdocs.org/service-documents/bell/sb-206-06-110/file/2ac864dcffde

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

ALERT SERVICE BULLETIN
Bell Helicopter TEXTRON  NO.  206-06-110
DATE  A Subsidiary of Textron Inc.  DATE  SEP 7, 2006
REV  PAGE  1 of 5
MODEL AFFECTED:  206A/B and TH-67 Series
SUBJECT:  UPPER LEFT-HAND TAILBOOM ATTACHMENT
HARDWARE, INSPECTION OF
HELICOPTERS AFFECTED:  All Model 206A/B helicopters serial number 4
through 4449 and model TH-67 helicopters 5101
through 5237 that had a 407-030-750-103 upper left-
hand CRES steel fitting field retrofitted.
All Model 206A/B helicopters serial number 4450
through 4617 and model TH-67 helicopters 5238
through 5312 that had a 407-030-750-103 upper left-
hand CRES steel fitting installed at manufacturing.
[Model 206A/B helicopters serial numbers 4618 and
subsequent will have the intent of this bulletin
accomplished prior to delivery. Model TH-67
helicopters serial numbers 5313 and subsequent will
have the intent of this bulletin accomplished prior to
delivery]
COMPLIANCE:  PART I Within the next 50 hours after receipt of this
bulletin.
PART II At the next scheduled 100 Hrs/annual
inspection, after Part I have been accomplished.
DESCRIPTION:
Bell Helicopter found that on some helicopters having the 407-030-750-103 CRES
steel fitting installed at the upper left-hand location, the attachment bolt might not meet
the installation requirement.
AN APPROPRIATE ENTRY SHOULD BE MADE IN THE AIRCRAFT LOGBOOK UPON ACCOMPLISHMENT
IF OWNERSHIP OF AIRCRAFT HAS CHANGED PLEASE FORWARD TO NEW OWNER

### Page 2 (OCR)

ASB 206-06-110
Page 2 of 5
PART I of this bulletin provides instructions to verify if a CRES steel fitting is installed
at the upper left-hand location and check for the amount of bolt threads exposed.
PART II of this bulletin provides instructions to replace the upper left-hand bolt if
required, as indicated in PART I.
APPROVAL:
The engineering design aspects of this bulletin are Transport Canada approved.
MANPOWER:
Approximately 0.5 man-hour is required to perform PART I and 1 man-hour to perform
PART II of this bulletin. Man-hours are based on hands-on time, and may vary with
personnel and facilities available.
WARRANTY:
Warranty does not apply for parts or labor associated with this bulletin.
MATERIAL:
Required Material:
The following material is required for the accomplishment of this bulletin and may be
obtained through your Bell Helicopter Textron Supply Center.
Part Number  Nomenclature  Quantity
NAS6606-25  Bolt
Note: The bolt may not require replacement. Refer to PART I.
SPECIAL TOOLS:
None required
WEIGHT AND BALANCE:
Not Affected

### Page 3 (OCR)

ASB 206-06-110
Page 3 of 5
ELECTRICAL LOAD DATA:
Not affected
REFERENCES:
BHT-206A/B-MM-5, Maintenance Manual
PUBLICATIONS AFFECTED:
BHT-206A/B-SERIES-IPB, Illustrated Parts Breakdown
BHT-206A/B-MM-5, Maintenance Manual
ACCOMPLISHMENT INSTRUCTIONS:
PART I. Left-hand upper fitting and bolt inspection.
1. Remove the tailboom attachment access door from right side of fuselage forward of
tailboom bulkhead as per BHT-206A/B-SERIES-MM, chapter 53.
2. Gain access to upper left-hand tailboom fitting (7, Figure 1).
-NOTE-
Helicopters 206B S/N 4450 through subsequent and TH-67
S/N 5238 through subsequent were delivered with CRES
steel fitting 407-030-750-103 installed.
3. For helicopters 206A/B S/N 4 through 4449 and TH-67 S/N 5101 through 5237,
verify if CRES steel fitting is installed. Those aircraft were originally delivered with
aluminum fitting that may have been replaced by the CRES fitting and longeron
assembly 206-031-314-201A. CRES steel fitting (7) may be identified as follows:
a. The part number 407-030-750-103 maybe stamped on the fitting.
b. Longeron and aluminum fitting were replaced by longeron assembly 206-031-
314-201A.
c. The CRES fitting 407-030-750-103 is composite bonded to the longeron and
the bonding layer might be visible.

### Page 4 (OCR)

ASB 206-06-110
Page 4 of 5
d. The CRES fitting 407-030-750-103 is ferrous and can be identified using a
magnet.
4. If the helicopter does not have a CRES fitting installed, no further action is
required. Make an entry in the helicopter records to indicate that this bulletin has
been accomplished.
5. For helicopters affected by this bulletin that have a CRES fitting installed, perform
thread count on the upper left hand attachment bolt (1) as per Figure 1.
6. If the correct amount of thread is exposed (between 1 and 3), do a torque check.
Refer to the Maintenance Manual. If the torque is correct, make an entry in the
helicopter records to indicate that this bulletin has been accomplished. If the torque
is found below minimum and a replacement bolt (1) is not available at this time,
adjust the washer (3) quantity as required per Figure 1. Refer to the Maintenance
Manual and torque as required. Make an entry in the helicopter records to indicate
that the PART I of this bulletin have been accomplished and that the PART Il of this
bulletin will require accomplishment.
7. If less than 1 thread is exposed, adjust the washer (3) quantity as required per
Figure 1. Refer to the Maintenance Manual and torque as required. Make an entry
in the helicopter records to indicate that this bulletin has been accomplished.
8. If more than 3 threads are exposed and a replacement bolt (1) is not available at
this time, adjust the washer (3) quantity as required per Figure 1. Refer to the
Maintenance Manual and torque as required. Make an entry in the helicopter
records to indicate that the PART I of this bulletin have been accomplished and
that the PART II of this bulletin will require accomplishment.
9. If more than 3 threads are exposed and a replacement bolt (1) is available,
accomplish PART II of this bulletin.
PART II. Upper left hand tailboom attachment bolt replacement.
1. Remove and discard the upper left hand tailboom attachment bolt (1, Figure 1).
Install new bolt (1) and adjust the quantity of washer (3) as required to ensure
correct installation as shown on Figure 1. If serviceable, the nut (4) does not
require replacement. Refer to Maintenance Manual.
2.  100 hours after installation, do a torque check of the upper left hand tailboom
attaching hardware (BHT-206A/B-SERIES-MM).
3. Make an entry in the helicopter records to indicate that this bulletin has been
accomplished.

### Page 5 (OCR)

ASB 206-06-110
Page 5 of 5
0123
From the end of the bolt,
a complete thread count starts
on the back face of the first
thread groove and moves
axially to the adjacent groove.
Three threads shown.
1. Bolt
2.  Washer, chamfered under bolt head
3. Washer, as required
4. Nut
5. Tailboom
6. AFT fuselage
7. Fitting
NOTES
Bolt (1) and chamfered washer (2) are to be installed through tailboom (5) and Aft
fuselage (6). Bolt head and chamfered washer are to be installed on the tailboom side.
Steel washers (3) are to be installed next to fitting (7) to provide not less than one thread
and not more than three threads exposed on threaded end of bolt (1).
If thread count is less than one, remove washers as required.
If thread count is more than three, remove and replace bolt, then readjust number of washers to meet
requirement of note 1.  RAM_06519_001_c1
Figure 1: Tailboom Attachment

### Page 6

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
