# Bell Alert Service Bulletin 407-07-80: No revision named

- Rights: © Bell Textron Inc. Filed by the FAA in regulations.gov docket FAA-2013-0574; AD 2014-04-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Bell Alert Service Bulletin 407-07-80](https://openairdocs.org/service-documents/bell/sb-407-07-80.md)
- Title as filed: Bell ASB-407-07-80
- Pages: 18
- PDF: https://openairdocs.org/files/sha256/55/ec/55ec22dcfc1dabce41b1eb2026913046101e5e35f72c38e74805fd21fcef121f
- Page: https://openairdocs.org/service-documents/bell/sb-407-07-80/file/55ec22dcfc1d

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

NO. 
  
DATE    
PAGE  
    DATE   
     
ALERT SERVICE BULLETIN 
 
 
 
A Subsidiary of Textron Inc. 
AN APPROPRIATE ENTRY SHOULD BE MADE IN THE AIRCRAFT LOGBOOK UPON ACCOMPLISHMENT 
IF OWNERSHIP OF AIRCRAFT HAS CHANGED PLEASE FORWARD TO NEW OWNER 
407-07-80 
 AUG 27, 2007 
 1 of 18 
 
 
MODEL AFFECTED:  407  
 
  
SUBJECT: TAILBOOM ASSE MBLY 407-030-801-107, AND 
407-530-014-101/-103, NEW  INSPECTION 
REQUIREMENTS. 
 
HELICOPTERS AFFECTED: Model 407 helicopters serial  number 53000 through 
53475 with subject tailboom installed. 
 
 [Model 407 helicopters se rial numbers 53476 and 
subsequent and serial numbers 53000 through 
53475 that have tailboom  407-030-801-201/-203/-
205 or later installed ar e not affected by the 
recurring inspections of this bulletin. 
 
COMPLIANCE: PART I  Immediately after receipt of this bulletin. 
 
PART II Within 25 flight-hours or 30 days after 
accomplishment of PART I. 
 
PART III  At the second flying day after 
accomplishment of Part II and before each first flight 
of the day thereafter. Compliance with this daily 
check can be accomplished by the pilot as part of 
his preflight check. 
 
PART IV  Within 100 flight-hours after 
accomplishment of PART II and every 100 flight-
hours thereafter.

### Page 2

ASB 407-07-80 
Page 2 of 18 
 
 
DESCRIPTION: 
 
CAUTION 
 
TAILBOOM ASSEMBLIES 407-030-801-107, 407-530-014-
101/-103 ARE AUTHORIZED FOR A MAXIMUM OF 5000 
HOURS IN SERVICE AFTER WHICH TIME THEY SHOULD 
BE RETIRED.  REMOVAL AND/OR REPLACEMENT OF 
THE UPPER AND/OR LOWER SKINS IS NO LONGER 
AUTHORIZED ON THE TA ILBOOM ASSEMBLIES 407-
030-801-107, 407-530-014-101/-103. 
 
Bell Helicopter received additional reports of cracked tailboom skins P/N 407-030-801-
157 affecting field-modified tailboom a ssemblies 407-530-014-101/-103 (Ref. ASB 
407-01-48) and original produc tion tailboom assembly P/ N 407-030-801-107.  Each 
report indicated a crack seen above the le ft side upper stabilizer attachment support, 
at Station 98.89.   Further investigation conduced by BHT revealed that other areas of 
the subject tailbooms do require additional attention. 
 
 
-NOTE- 
Tailboom 407-030-801-101 and /-105 shall have had ASB 
407-01-48 Rev. “B” accomplishe d as of January 31, 2003 
therefore converted to tailboom 407-530-014-101/-103. 
 
-NOTE- 
Terminating action to this Alert Service Bulletin is 
replacement of the affected tailboom assembly 407-530-014-
101/-103 or 407-03 0-801-107 by tailboom 407-030-801-
201/-203/-205 or later. 
 
PART I of this Alert Service Bulletin requires identification of the affected tailboom. 
 
PART II of this bulletin gives instructions to remove the paint and the primer from the 
left side of the tailboom at two specific areas to allow detailed inspection. 
 
PART III of this bulletin introduces a daily vis ual check of the specific areas where 
paint and primer were removed under Part II. Compliance with this daily check can be 
accomplished by the pilot as part of his preflight check. 
 
PART IV changes the intervals of the scheduled inspection requirements described in 
Revision 23 of the Chapter 4 of the Main tenance Manual (BHT-407-MM-1, Table 4.2) 
to 100 Flight-hours and adds t he new inspection requirements as defined by this 
bulletin. It also supersedes the inspection requirements as defined under PART V of 
Alert Service Bulletin 407-01-48 (Revision “B”).

### Page 3

ASB 407-07-80 
Page 3 of 18 
 
 
 
APPROVAL: 
 
The engineering design aspects of this bulletin are TCCA approved. 
 
MANPOWER: 
 
PART I: Approximately  0.5 man-hour is required to accomplish PART I of this bulletin. 
 
PART II:  Approximately 1.5 man- hours are required to accomplish PART II of this 
bulletin.  
 
PART III:  No more time is necessary if this check is being done as part of the Pilot’s 
Preflight check. 
 
PART IV: Approximately 2.5 man-hour s are required to accomplish PART IV of this 
bulletin.  
 
NOTE: Man-hours are based on hands-on time , and may vary with personnel and 
facilities available.  
 
WARRANTY: 
 
Owners / Operators of the affected tailbooms that have completed Part 1, Part II (1.g.), 
Part III (1.d.) or Part IV (3.a.) of this bulletin and hav e found a crack in the detailed 
area listed in this bulletin may replace their tailboom at no cost providing you purchase 
a replacement tailboom part num ber 407-030-801-205 or later from  a Bell approved 
supply source. 
 
Order a replacement tailboom through the Bell Spares Depar tment or Bell approved 
source at full list price, and file a warranty claim in VIST A. Warranty administration will 
credit your account based on replacement part invoice cost. In addition, Bell Warranty 
will offer a maximum of $2,100. 00 for labor to remove and replace the tailboom, shim 
and install the horizontal stabilizer, re- wire and paint the ta il boom. An additional 
$400.00 maximum will be allowed for the cost of the paint. 
 
NOTE: Once you have replaced the tailboom, please remove the data plate from the 
unserviceable tailboom and notify Product Support Engineering Light Group of the 
serial number removed. Also notify your local CSR who will pick the data plate, and 
witness the destruction of the discrepant part.

### Page 4

ASB 407-07-80 
Page 4 of 18 
 
 
MATERIAL: 
 
Required Material: 
 
None required. 
 
Consumable Material: 
 
For PART II:   
 Paint stripper (C-436) under  MIL-R-81294A OR MIL-R-8633A. 
 Aluminum tape C-439, Aluminum Tape 425-2IN. 
 Clear polyurethane paint coating (C-245) . Clear enamel coating in a spray can 
which is procured locally is an acceptabl e alternate to the clear polyurethane 
coating. 
 2 inch wide paint brush 
 
For PART III or PART IV:  
 Aircraft soap (C-318) under MIL-C-87936, as required. 
 
SPECIAL TOOLS: 
 
For PART II and PART IV: 10X Magnifying glass 
 
WEIGHT AND BALANCE: 
 
Not affected 
 
ELECTRICAL LOAD DATA: 
 
Not affected 
 
REFERENCES: 
 
ASB 407-01-48, Revision “C”  
ASB 407-07-77, dated March 28, 2007 
BHT-206-SRM-1 
BHT-407-MM-1, Rev 23, Maintenance Manual, Chapter 4 
BHT-407-MM-5, Rev 18, Maintenance Manual, Chapter 53 
Corrosion Control Guide, Chapter 10 
BHT-ALL-SPM, Rev. 2, dated 16 February, 2007 
 
PUBLICATIONS AFFECTED: 
 
BHT-407-MM-1, Rev 23, Maintenance Manual, Chapter 4 
ASB 407-01-48, Revision “B “

### Page 5

ASB 407-07-80 
Page 5 of 18 
 
 
 
ACCOMPLISHMENT INSTRUCTIONS: 
 
PART I    VERIFICATION FOR AFFECTED TAILBOOM.  
 
1. Upon receipt of this bulletin,  verify the helicopter technical records to 
determine if you have a tail boom 407-030-801-107,  or 407-530-014-
101/103 installed. You can also ph ysically confirm the tailboom part 
number by removing the aft driveshaft cover and looking at the 
identification plate located near Boom Station (BS) 129 as shown in Figure 
1. 
 
2. If identification as per Step 1 indicates that your tailboom is not affected by 
this bulletin, (meaning that you hav e a tailboom assembly 407-030-801-
201/-203 or /-205 (or later) installed on your helicopter), annotate the 
helicopter technical records to indicate that your tailboom is not affected by 
this bulletin.  
 
3. If identification as per  Step 1 above indicates that you have one of the 
subject tailboom assembly, annotate t he helicopter technical records to 
indicate the date and the helic opter total time at which PART I of this 
bulletin is complied with. 
 
4. Accomplish Part II  within 25 hours of flight-t ime or 30 days following 
identification of affected tailboom under PART I of this bulletin. 
 
PART II Preparation of tailboom asse mbly for Daily visual check (under 
  PART III) and for 100 Hour-10X magnifying glass inspection (under 
  Part IV). 
 
1. Remove the paint and prim er from the left side only of your tailboom in the 
areas ( 1.5 inch X 2 inch( 38.1 mm X 50.8 mm)) shown under Figure 2 as 
follows; 
 
-CAUTION- 
Once the paint and the primer  is removed, and following 
initial 10X magnifying glass inspection, the unpainted 
surfaces must be protected fr om corrosion by application of 
a  clear paint coating (see c onsumable material section for 
details). 
 
a) Use soap (C-318) prepared in accordance with manufacturer’s 
recommendations to clean all exhaus t residues and dirt from the 
tailboom surfaces shown in Figure 2.

### Page 6

ASB 407-07-80 
Page 6 of 18 
 
 
b) Refer to Figure 2 and use a felt marker to layout each area where the 
paint must be removed. 
 
c) Use Aluminum tape (C-439) to ma sk external area of each section 
identified in previous step. Make sure you put sufficient pressure over 
complete surfaces and edges of tape to get ultimate adhesion to the 
painted surfaces.  
-NOTE- 
Do not remove sealant if present at edge of the upper 
stabilizer attachment support, at this time. This will be done 
later. 
-CAUTION- 
Protect other areas of the tailboom and the horizontal 
stabilizer from the paint stripper.  
 
d) Use a 2 inch wide (or smaller) pai nt brush and apply a thin coat of 
paint stripper (C-436) to each area.  Wait a few minutes until all paint 
and primer is separating from the tailboom skin surface.  Use clean 
cloth to wipe paint, primer and st ripper residues.  Re-apply new 
stripper as required. Repeat this  process until the bare tailboom 
Aluminum skin is revealed (normally 2 or 3 times should suffice).  
 
e) Rinse reworked surfaces with soft water until all traces of paint 
stripper compound is removed. Wi pe again the surfaces with dry 
cloth. If sealant is present at edge of stabilizer attachment support, 
remove it at this time with a plastic scrapper (or equivalent tool) but be 
careful not to damage the tailboom skin during removal process.  
 
f) Inspect both areas using a 10X magnifying glass.  Pay close 
attention near edges of the stabilizer upper attachment support. 
 
g) If a crack is found, replace the ta ilboom before next flight and notify 
Bell Helicopter Product Support Engineering department. 
 
h) If another affected tailboom is inst alled on the helicopter, proceed 
with PART II or PART III of this bulletin, as applicable, prior to next 
flight. 
 
-NOTE- 
Clear enamel coating applied from a spray can is acceptable 
as an alternate to the clear polyurethane coating (C-245). 
 
i) If no crack is found, make sure  both surfaces are dry and protect 
each reworked area with a thin coat  of clear coating(C-245). Do not 
re-apply sealant if removed previously.

### Page 7

ASB 407-07-80 
Page 7 of 18 
 
 
 
j)  Let the clear coating dry and remove the Aluminum tape. 
 
PART III Daily visual check.  
-NOTE- 
This check requires no special tool but the paint and primer 
must be initially removed from  the tailboom skin surface in 
accordance with PART II. Compliance with this Daily check 
can be accomplished by the pilot as part of his preflight 
check. 
 -NOTE- 
Do not remove the clear paint coating to comply with this 
daily check. 
 
-NOTE- 
If your helicopter has not flown since accomplishment of 
PART II , start the daily checks at  the second forthcoming 
day of flight.  
 
1. Before the first flight of the day, do a check for cracks in the areas where 
paint was removed on the left side of the tailboom assembly, as follows; 
 
a) Use a clean cloth moistened with  aircraft soap (C-318) prepared in 
accordance with manufacturer’s recommendations, as required, to 
remove any exhaust residues or dirt  from both areas to look at, as 
shown in Figure 2.  
 
b) Make sure that the tailboom skin is clean and t hat adequate lighting 
exists.  Visually look at the two ar eas where original paint and primer 
was removed and protected with clear paint coating. Look for a crack 
at a distance not exceeding more  than 12 inches (30.48 cm) from 
eyesight.  
 
c)  Pay close attention near the edge of the stabilizer upper support. 
 
d) If a crack is found, replace the ta ilboom before next flight and notify 
Bell Helicopter Product Support Engineering department. 
 
e) If another affected tailboom is inst alled on the helicopter, proceed 
with PART II or PART III of this bulletin as applicable, prior to next 
flight. 
 
f) If no crack is found, the intent of PART III is complete.

### Page 8

ASB 407-07-80 
Page 8 of 18 
 
 
2. Make an entry in the helic opter records to show that PART III  of this 
bulletin is completed.   
 
3. Repeat steps 1 and 2 before each firs t flight of the day thereafter.  
 
4. Comply with subsequent 100 Hour inspection requirements described in 
PART IV when time is reached. 
 
PART IV: 100 Hour  inspection re quirements for tailbooms 407-530- 
  014-101 /-103 and tailboom 407-030-801-107. 
 
-NOTE- 
PART IV changes the intervals of the scheduled inspection 
mandated by Revision 23 of  the Chapter 4 of the 
Maintenance Manual (BHT-407 -MM-1, Table 4.2) for all 
tailbooms listed in the subject bl ock.  It also supersedes the 
inspection requirements as defined under PART V of Alert 
Service Bulletin 407-01-48 (Revision “B”).  
 
1. Gain access to the areas to be ins pected by removing both driveshaft covers 
and both gearbox fairings halves from your  tailboom assembly. Refer to (BHT-
407-MM-5, Chapter 53). 
 
2. Clean the complete tailboom assembly (including the horizontal stabilizer, the 
two auxiliary finlets and the vertical fin) with aircraft s oap (C-318) prepared in 
accordance with manufacturer’s recommendati ons to remove all traces of dirt, 
stains, exhaust residues and oil.  
 
3. Examine the complete tailboom assembly P/N 407- 530-014-101/-103 or 
tailboom 407-030-801-107 ev ery 100 Hours of operati on for general condition, 
loose rivets, cracks or any other type of damage.  Pay close attention to Area 
“A” indicated in Figure 3 for the left side of the tailboom.  
 
a) If a crack is found, replace the ta ilboom with a serviceable unit prior 
to next flight and notify Bell Helic opter Product Supp ort Engineering 
department. 
 
b) If any other type of damage is f ound, refer to the negligible damage 
limits found in Chapter  53 of your maintenanc e manual or contact 
Product Support Engineering department for assistance.  
 
4. Inspect for loose rivets in region show n in Figure 3, Area  “A” and especially in 
Details “E”, “F”,  “G”, “H”,  “I” and Views “D” and “J”.   If  a loose rivet or fastener 
is found, remove it per standard practi ces and inspect hole for cracks using a

### Page 9

ASB 407-07-80 
Page 9 of 18 
 
 
10X magnifying glass. If no crack is foun d, install correct diameter rivet or 
fastener (Ref. BHT-206-SRM-1, section 3). 
 
5. If no loose rivets or fasteners are found loose, use a 10X magnifying glass and  
examine tailboom skin at  edge of mating suppor ts/brackets and around 
fasteners shown in Figure 3, Details  “E”, “F”, “G”, “H”, “I” and View “D”. 
 
6. On left side of tailboom, use a 10X magnifying glass and examine tailboom skin 
at edge of mating supports/brackets and around fasteners shown in Figure 3 
Area “C” and View “J”.   
 
a) Pay close attention to both areas where clear paint coating exists.   
 
b) Make sure that the clear paint c oating is in good condition and it does 
not obstruct inspection of the ar ea (not opaque). If coating needs 
replacement, refer to PART II.  
 
c) Make sure the skin is not corroded. 
 
7. If any crack is found in Step 3 through Step 6 above, replace the tailboom with 
a serviceable unit before the next fli ght and notify Bell He licopter Product 
Support Engineering depar tment.  If corrosion is found, refer to Chapter 53 of 
your maintenance manual for negligible  damage limit or contact Product 
Support Engineering with details for assistance.  
 
8. If another tailboom affected by this bu lletin is installe d on the helicopter, 
proceed with PART II or PART III of this bulletin, as applicable,  prior to next 
flight.  
 
9. If no crack is found, annotat e the helicopter technical records to indicate that 
PART IV of this bulletin is complied with and return the tailboom to flight status. 
 
10. Carry subsequent Daily inspections as per PART III. 
 
11. Repeat this inspection every 100 flight-hours thereafter.  
  
AFFECTED TAILBOOMS, GENERAL MAINTENANCE 
 
1. Maintain your tailboom in accor dance with your 407 Maintenance Manual 
BHT-407-MM-1 and the BHT corrosion control guide CSSD-PSE-87-001. 
 
2. Inspect your tailboom as per applic able requirements and recurring intervals 
as described herein.

### Page 10 (OCR)

ASB 407-07-80
Page 10 of 18
BS  - MODIFICATION PLATE
125.74  (REF ASB-407-01-48)
REF
FWD
EXISTING DATA PLATE
LOOKING DOWN AT TAILBOOM
07538_001
Figure 1. Location of identification plate, tailbooms 407-530-014-101, 407-
530-014-103 or 407-030-801-107

### Page 11 (OCR)

ASB 407-07-80
Page 11 of 18
1.5 IN  (38.1 mm)  2.0 IN  (50.8 mm)
B.S.  120.75  REF
+  +  Tailboom assembly (Ref.)  Horizontal stabilizer (Ref.)  Upper support (Ref.)  Lower support (407-023-800-121)  Paint and primer to be removed from these areas (see PART II).  Examine these areas for cracks on left side of tailboom only.  3. Horizontal stabilizer not shown for clarity.  Daily check area
NOTES
2.0 IN  (50.8 mm
07538_009
Figure 2.  Daily check, tailbooms 407-530-014-101, 407-530-014-103 or 407-
030-801-107

### Page 12 (OCR)

ASB 407-07-80
Page 12 of 18
BS
140.428
REF
BS
федора.  107.397
REF  AREA D
BS  _ AREA A
72.370
REF
AREA C
BS
90.00
REF
AREA B  07538_002
BS
39.00
REF
100 HOUR VISUAL INSPECTION
8 CRITICAL INSPECTION AREAS (SEE DETAILS)
Figure 3.  100 Hour inspection of tailbooms 407-530-014-101, 407-530-014-103
and 407-030-801-107 (Sheet 1 of 7).

### Page 13 (OCR)

ASB 407-07-80
Page 13 of 18
BS  BS  BS
31.920  74.370  90.00
REF  REF  REF
SEE DETAIL I
BL
0.00
REF
LBL
• AREA B -  7.50
REF
SEE  SEE  SEE  SEE  SEE
DETAIL E  DETAIL F  DETAIL G  DETAIL G  DETAIL H
BS  BS  BS  BS  BS  BS  BS
39.000  45.515  52.600  58.995  72.475  77.000  85.955
REF  REF  REF  REF  REF  REF  REF
AREA B
FWD
.50 IN.
BL  .50 IN.  (12.7 mm)  •  (12.7 mm)
0.00
REF
LBL
7.50
REF
(9 FASTENERS)
LEFT SIDE ONLY
BS
45.515
DETAIL E  REF
GENERAL VISUAL INSPECTION (100 HOURS)
100 HOUR INSPECTION (10X MAGNIFYING GLASS)
07538_003
Figure 3.  100 Hour inspection of tailbooms 407-530-014-101, 407-530-014-103
and 407-030-801-107 (Sheet 2 of 7).

### Page 14 (OCR)

ASB 407-07-80
Page 14 of 18
REFER TO  REFER TO
DETAIL E  DETAIL I
FOR DIMENSIONS  FOR DIMENSIONS
FWD
3.5 IN. DIA
88.9 mm
BL  APPROX.
0.00
REF
/3 (3 RIVETS)
LEFT SIDE ONLY
BS  BS  BS
45.515  52.600  58.995
REF  REF  REF
DETAIL F
BS
FWD  72.475
REF
BL
0.00
REF
LEFT SIDE ONLY  (10 RIVETS)  LBL  7.50
REF
6.00 IN.
(152.4 mm)
DETAIL G  07538_004
GENERAL VISUAL INSPECTION (100 HOURS)
100 HOUR INSPECTION (10X MAGNIFYING GLASS)
Figure 3.  100 Hour inspection of tailbooms 407-530-014-101, 407-530-014-103
and 407-030-801-107 (Sheet 3 of 7).

### Page 15 (OCR)

ASB 407-07-80
Page 15 of 18
FWD  - 0.50 IN. (12.7 MM)
TYPICAL ALL PLACES
EXCEPT AS SHOWN  BL
0.00
REF
BS
85.955
REF
DETAIL H
0.50 IN. (12.7 mm)
TYPICAL ALL PLACES
EXCEPT AS SHOWN
07538_005
BS
58.995
REF
DETAIL I
GENERAL VISUAL INSPECTION (100 HOURS)
100 HOUR INSPECTION (10X MAGNIFYING GLASS)
Figure 3.  100 Hour inspection of tailbooms 407-530-014-101, 407-530-014-103
and 407-030-801-107 (Sheet 4 of 7).

### Page 16 (OCR)

ASB 407-07-80
Page 16 of 18
(8 RIVETS)
LEFT SIDE ONLY
BS  BS  BS
97.89  98.89  107.397
REF  REF  REF  SEE  BS  BS
VIEW J  120.75  121.75
REF  REF
4 IN.
(101.6 mm)  4 IN.
— (101.6 mm)
4 IN.
(101.6 mm)  4 IN.
(101.6 mm)
HORIZONTAL
STABILIZER
(REF)
2 IN.  2 IN.
(50.8 mm)  - (50.8 mm)
AREA C
BS
107.397
FWD  REF
BL
0.00
REF
(8 RIVETS)
LEFT SIDE ONLY
•
LBL
7.00
07538_006  REF
3.00 IN.
- (76.2 mm)
VIEW J
GENERAL VISUAL INSPECTION (100 HOURS)
100 HOUR INSPECTION (10X MAGNIFYING GLASS)
Figure 3.  100 Hours inspection of tailbooms 407-530-014-101, 407-530-014-
103 and 407-030-801-107 (Sheet 5 of 7).

### Page 17 (OCR)

ASB 407-07-80
Page 17 of 18
SEE
VIEW D
BS
140.428
REF
LEFT SIDE ONLY
AREA D
BS
FWD  140.428
REF
BL
0.00
REF
(6 RIVETS)  LBL
LEFT SIDE ONLY  5.00
REF
6.00 IN.
(152.4 mm)
VIEW D  07538_007
GENERAL VISUAL INSPECTION (100 HOURS)
100 HOUR INSPECTION (10X MAGNIFYING GLASS)
Figure 3.  100 Hour inspection of tailbooms 407-530-014-101, 407-530-014-103
and 407-030-801-107 (Sheet 6 of 7).

### Page 18 (OCR)

ASB 407-07-80
Page 18 of 18
100 Hours of Operation
NOTES
1.  Inspect the complete tailboom assembly for general condition.
2  On the left side of the tailboom only, do a detailed inspection of all areas shown for cracks in the tailboom skin and loose
rivets. Do not remove the paint or primer. If a loose rivet is found, remove rivet and inspect hole for cracks using a 10x
magnifying glass. If no cracks are found, install correct diameter rivet. Do not exceed maximum diameter prescribed.
Use a 10X magnifying glass to inspect for cracks in tailboom skin and around fastener heads as indicated
in area shown in Detail E, F, G, H, I, View J, View D and Area C.
Do not remove horizontal stabilizer.
5.  Some tailboom components not shown for clarity.
6.  If a crack is found on the tailboom skin, replace the tailboom before the next flight and contact Product Support
Engineering at the following numbers:
Bell Helicopter Textron
Product Support Engineering
Light Helicopters
Tel: 1-800-243-6407 (Continental USA and Canada)
Tel: 1-800-363-8023 (Continental USA)
Tel: 1-800-361-9305 (Within Canada)
Tel: 1-450-437-2682 (All other areas - call collect)
Fax: 450-433-0272  Internet: pselight@bellhelicopter.textron.com  07538_010
Figure 3. 100 Hour inspection of tailbooms 407-530-014-101, 407-530-014-103
and 407-030-801-107 (Sheet 7 of 7).

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
