# Bell Alert Service Bulletin 407-08-84: No revision named

- Rights: © Bell Textron Inc. Filed by the FAA in regulations.gov docket FAA-2013-0019; AD 2013-12-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Bell Alert Service Bulletin 407-08-84](https://openairdocs.org/service-documents/bell/sb-407-08-84.md)
- Title as filed: U.S. DOT/FAA - Bell ASB No 407-08-84
- Pages: 26
- PDF: https://openairdocs.org/files/sha256/5e/ee/5eeed64d75d7d16c332f6e9f89d90de120f3921d1ad099918a6efc599c33e328
- Page: https://openairdocs.org/service-documents/bell/sb-407-08-84/file/5eeed64d75d7

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

NO. 
  
DATE    
PAGE 
    DATE   
     
ALERT SERVICE BULLETIN 
 
 
 
A Subsidiary of Textron Inc. 
AN APPROPRIATE ENTRY SHOULD BE MADE IN THE AIRCRAFT LOGBOOK UPON ACCOMPLISHMENT 
IF OWNERSHIP OF AIRCRAFT HAS CHANGED PLEASE FORWARD TO NEW OWNER 
407-08-84 
 Aug. 18, 2008 
 1 of 26 
 
 
MODEL AFFECTED:  407  
 
  
SUBJECT: TAILBOOM A SSEMBLY 407-030-801-201, 407-
030-801-203 AND 407-030-801-205, NEW  
INSPECTION REQUIREMENTS. 
 
HELICOPTERS AFFECTED: All model 407 helicopters with one of the subject 
tailbooms installed.  
 
  
COMPLIANCE: PART I  Immediately after receipt of this bulletin. 
 
PART II At the next tailboom  scheduled inspection 
and after every 300 flight-hours thereafter. 
 
PART III  Within 25 flight- hours or 30 days after 
accomplishment of Part I. This inspection will affect 
tailbooms which have accumulated 6900 flight-hours 
or more, tailbooms with unknown total flight-hours or 
tailbooms reaching 6900 flight-hours in service. 
 
PART IV  Within 25 flight-hours or 30 days after 
accomplishment of Part I. This inspection will affect 
tailbooms which have accumulated 8600 flight-hours 
or more, tailbooms with unknown total flight-hours or 
tailbooms reaching 8600 flight-hours in service. 
 
DESCRIPTION: 
 
Bell Helicopter Textron (BHT) has a ccomplished a thorough analysis of subject 
tailbooms which are built wit h chem-milled skins. This an alysis has revealed that 
areas with high stress concentration could ex ist on the subject tailboom. BHT has not 
received any field report indicating a crack ed skin in service on subject tailbooms.  
However, in the interest of safety, BHT has elected to introduce a new inspection 
schedule to subject tailboom assemblies.

### Page 2

ASB 407-08-84 
Page 2 of 26 
 
 
PART I of this Alert Service Bulletin requires identification of the affected tailboom. 
 
PART II of this bulletin provides the new 30 0-hour recurring inspection details for all 
subject tailbooms. 
  
PART III of this bulletin provides additional in spection details for subject tailbooms 
which have accumulated 6900 flight-hours or more or with total flight-hours 
unknown. Operators have the option to  meet the requirement of PART III with a 10X 
magnifying glass inspection (Option “A”) performed every 150 flight-hours thereafter or 
by an Eddy Current inspection method (O ption “B”) performed at every 500-hours 
interval.  
 
PART IV of this bulletin provides additional in spection details for subject tailbooms 
which have accumulated 8600 flight-hours or more or with total flight-hours 
unknown. Operators have the option to  meet the requirement of PART IV with a 10X 
magnifying glass inspection (Option “A”) pe rformed by maintenance personnel every 
50 flight-hours thereafter or a visual check (Option “B”) performed daily by the pilot as 
part of his daily preflight check. 
 
PART V of this bulletin provides the Instructions for Continued Airworthiness. 
 
APPROVAL: 
 
The engineering design aspects of this bulletin are TCCA approved. 
 
MANPOWER: 
 
PART I : Approximately 0.25 man-hour is required to accomplish PART I  of this 
bulletin. 
 
PART II:  Approximately 2.5 man-hours are required to accomplish PART II  of this 
bulletin.  
 
PART III: Approximately 0.50 man-hour is required to accomplish PART III  of this 
bulletin when done under Option “A” (10X magni fying glass inspection method) or 1.0 
man-hour when done under Option “B” (Eddy Current inspection method). 
 
PART IV:  Approximately 0.25 man-hour is required to accomplish PART IV, Option 
“A” of this bulletin. There is no impact when Option “B” is selected and done as part of 
the pilot’s daily preflight check. 
 
NOTE: Man-hours are based on hands-on time , and may vary with personnel and 
facilities available.

### Page 3

ASB 407-08-84 
Page 3 of 26 
 
 
 
WARRANTY:  
 
There is no warranty associated with this bulletin. 
 
MATERIAL: 
 
Required Material: 
 
None required. 
 
Consumable Material: 
 
For PART II, PART III and PART IV:  
 Aircraft soap (C-318) under MIL-C-87936, as required. 
 
SPECIAL TOOLS: 
 
For Part III, Option “B”(when selected): Eddy Current inspection equipment as 
described in paragraph 3.0 of Appendix “A”. 
 
WEIGHT AND BALANCE: 
 
Not affected 
 
ELECTRICAL LOAD DATA: 
 
Not affected 
 
REFERENCES: 
 
ASB 407-07-80 
BHT-206-SRM-1 
BHT-407-MM-1, Rev 24, Maintenance Manual, Chapter 4 
BHT-407-MM-5, Rev 18, Maintenance Manual, Chapter 53 
Corrosion Control Guide, Chapter 10 
BHT-ALL-SPM, Rev. 2, dated 16 February, 2007 
 
PUBLICATIONS AFFECTED: 
 
BHT-407-MM-1, Rev 24, Maintenance Manual, Chapter 4

### Page 4

ASB 407-08-84 
Page 4 of 26 
 
 
 
ACCOMPLISHMENT INSTRUCTIONS: 
 
PART I: Verification of affected tailboom:  
 
1. Upon receipt of this bulletin,  verify the helicopter technical records to determine if 
you have tailboom assembly part num ber 407-030-801-201,  407-030-801-203 or 
407-030-801-205 installed on your  helicopter. You can also physically confirm the 
tailboom Part Number by removing the aft driveshaft cover (Ref. Chapter 53 of the 
maintenance manual) and looki ng at the identification plate located near Boom 
Station (BS) 129 as shown in Figure 1. 
 
2. If identification as per Step 1 indicates that your tailboom is P/N 407-030-801-107, 
407-530-014-101 or 407- 530-014-103, refer to Chapter  4 of your maintenance 
manual for the inspection schedule appli cable to those tailboom assemblies. 
Annotate the helicopter technical records to  indicate that your tailboom is not 
affected by this bulletin. 
  
3. If identification as per Step 1 above i ndicates that you have one of the subject 
tailboom assemblies, verify tailboom histor ical record sheet to determine total 
flight-hours of your tailboom.   
 
-NOTE- 
 
If the total flight-hours of your tailboom is unknown, it will be 
considered to have accumula ted beyond 8600 flight-hours 
and the requirements described under PART II , PART III  
and PART IV will apply 
 
4. Once the total time in service is known;  
 
a) For all subject tailbooms, regardless of their total time in service, accomplish 
inspection of your tailboom assembly as defined under PART II of this bulletin 
at the next scheduled inspection and every 300 flight-hours thereafter.  
 
b) If your tailboom assembly has accumulated 6900 flight-hours or more or if the 
total time is unknown, incorporate into  the inspection schedule of subject 
tailbooms defined under PART II, one of the additional in spections as defined 
under PART III within the next 25 fli ght-hours in service or 30 days, whichever 
occurs first and repeat at applicable interval shown.  
 
c) If your tailboom assembly has accumulated more than 8600 flight-hours  or if 
the total flight-hours is unknown, incor porate into the insp ection schedule of 
subject tailbooms defined under PART II and PART III , one of the additional

### Page 5

ASB 407-08-84 
Page 5 of 26 
 
 
inspections as defined under PART IV  within 25 flight-hours or 30 days, 
whichever occurs first and repeat at applicable interval shown.  
 
5. Annotate your technical record s to indicate at which time PART I of this bulletin 
was carried out.  
 
 
PART II Inspection requirements at each  300-hour interval for all subject 
tailbooms: 
 
1. Gain access to the areas to be inspected by removing both driveshaft covers and 
both gearbox fairings halves from your tailboom assembly. Refer to BHT-407-MM-
5, Chapter 53. 
 
2. Clean the complete tailboom assembly (including the horizontal  stabilizer, the two 
auxiliary finlets and the vertical fin)  with aircraft soap (C-318) prepared in 
accordance with manufacturer’s recommendati ons to remove all traces of dirt, 
stains, exhaust residues and oil. 
 
3. (Ref. Figure 2) Examine the complete tailboom assembly following every 300 flight-
hours of operation for general condition, loos e rivets, cracks or any other type of 
damage.  Pay close attention to Areas “B”, “C”, “D”, “H” and “I” at the left side of 
the tailboom as indicated in Figure 2.  
 
4. Inspect for loose rivets in region show n in Figure 2, Area  “A” and especially at 
those shown in Details “E”, “F”, “G”, and in Areas “C”, “D”, “H” an d “I”.   If a loose 
rivet or fastener is found, remove it per  standard practices and inspect edges of 
hole for cracks using a 10X magnifying gla ss. If no crack is found, install correct 
diameter rivet or fastener (Ref. BHT-206-SRM-1, section 3). 
 
5. If no loose rivets or fasteners are found,  use a 10X magnifying glass and  examine 
tailboom skin at edge of bearing hanger supports and around fa steners shown in 
Figure 2, Details  “E”, “F”, “G”, and Areas “H” and “I”. 
 
6. On left side of tailboom, use a 10X magnifying glass and examine tailboom skin 
just above edge of mating stabilizer upper a ttachment support as shown in Figure 
2, Areas “C” and ”D”.   
 
7. If no crack is found, annotat e the helicopter technical records to indicate that PART 
II of this bulletin is complied with and return the tailboom to flight status. 
 
8. Repeat this inspection after every 300 flight-hours thereafter. When your tailboom 
reaches 6900 and 8600 flight-hours of serv ice, add respectively to this inspection 
schedule, the applicable recurring insp ection requirements as defined under 
PART III and PART IV of this bulletin.

### Page 6

ASB 407-08-84 
Page 6 of 26 
 
 
 
9. If any crack is found in Step 3 through St ep 6 above, replace the tailboom with a 
serviceable unit prior to next  flight and notify Bell  Helicopter Product Support 
Engineering department; 
 
a) If another affected tailboom is installed on the helic opter, determine the total 
time in service of that tailboom and app ly appropriate inspection program as 
defined in this bulletin.  
 
b) If the total flight-hours of your ta ilboom is unknown, accomplish inspection 
requirements described under PART II, PART III and PART IV before putting 
this tailboom in service and repeat at in tervals shown or selected until directed 
otherwise by BHT. 
 
10. If corrosion is found, refer to Chapter 53 of your maintenance manual for negligible 
damage limits or contact Product Support Engineering with details for assistance.  
 
 
PART III Additional inspection requireme nts for tailbooms with 6900 flight-
hours or more or with time unknown: 
 
For tailbooms which have reached or exceeded 6900 flight-hours in service or with 
time unknown, in addition to PART II, incorporate to the inspec tion schedule, one of 
the following recurring inspections and repeat at the applicable interval shown; 
 
Option “A” (10X Magnifying glass 150-hour recurring inspection): 
 
-NOTE- 
 
It is permissible to transfer from one inspection program to 
the other for maintenance scheduling convenience (ex: 
Option “A” to Option “B). However, the inspection as 
described in the new program must be accomplished prior to 
next flight. Make an entry in t he helicopter records to show 
that you have transferred from one inspection option to the 
other for traceability.  
 
-NOTE- 
 
The following inspection must be repeated at a maximum of 
150 flight-hours of time in se rvice.  However, the aft 
driveshaft cover section from the tailboom assembly must be 
removed to gain proper access to the area to be inspected.

### Page 7

ASB 407-08-84 
Page 7 of 26 
 
 
1. Remove the aft driveshaft cover secti on in accordance with Chapter 53 of the 
maintenance manual.  
 
2. Use a clean cloth moistened with airc raft soap (C-318) prepared in accordance 
with manufacturer’s recommendations, as  required, to remove any exhaust 
residues or dirt from areas to inspect, as shown in Figure 2, Areas “H” and “I”.  
 
3. On left side of tailboom, make sure that the tailboom skin is clean and that 
adequate lighting exists.  Use a 10X m agnifying glass and examine tailboom 
around fasteners shown in Figure 2, Areas “H” and “I”. 
 
4. If a crack is found, replace the tailboom with a serviceable unit prior to next flight 
and notify Bell Helicopter Product Support Engineering department; 
 
a) If another affected tailboom is installed on the helic opter, determine the total 
time in service of that tailboom and apply appropriate inspection program as 
defined in this bulletin.  
 
b) If the total flight-hours of your ta ilboom is unknown, accomplish inspection 
requirements described under PART II, PART III and PART IV before putting 
this tailboom in service and repeat at in tervals shown or selected until directed 
otherwise by BHT. 
 
5. If no crack is found, the intent of PART III is complete.  
 
6. Make an entry in the helicopter records to show that PART III, Option “A” of this 
bulletin is completed.   
 
7. Repeat this inspection after ev ery 150 flight-hours thereafter.  
 
8. When your tailboom reaches 8600 flig ht-hours, one of the additional recurring 
inspection requirements defined under PART IV must apply. 
 
Option “B” (Eddy Current 500-hour recurring inspection); 
 
-NOTE- 
 
It is permissible to transfer from one inspection program to 
the other for maintenance scheduling convenience (ex: 
Option “B” to Option “A). However, the inspection as 
described in the new program must be accomplished prior to 
next flight. Make an entry in t he helicopter records to show 
that you have transferred from one inspection option to the 
other for traceability.

### Page 8

ASB 407-08-84 
Page 8 of 26 
 
 
-NOTE- 
 
The following inspection must be repeated at a maximum of 
500 flight-hours of time in se rvice.  However, the aft 
driveshaft cover section from the tailboom assembly must be 
removed to gain proper access to the area to be inspected.  
 
1. Remove the aft driveshaft cover secti on in accordance wit h Chapter 53 of the 
maintenance manual.  
 
2. Use a clean cloth moistened with airc raft soap (C-318) prepared in accordance 
with manufacturer’s recommendations, as  required, to remove any exhaust 
residues or dirt from areas to inspect, as shown in Figure 2, Areas “H” and “I”. 
 
3. Refer to Appendix “A” to set and calibra te the Eddy Current inspection equipment. 
 
4. On left side of tailboom, make sure that the tailboom skin is clean and inspect 
tailboom skin around fasteners heads in t he shaded areas shown in Figure 2, 
Areas “H” and “I”. 
 
5. If a crack is detected, replace the tailb oom with a serviceable unit prior to next 
flight and notify Bell Helicopter Product Support Engineering department; 
 
a) If another affected tailboom is installed on the helic opter, determine the total 
time in service of that tailboom and app ly appropriate inspection program as 
defined in this bulletin.  
 
b) If the total flight-hours of your ta ilboom is unknown, accomplish inspection 
requirements described under PART II, PART III and PART IV before putting 
this tailboom in service and repeat at in tervals shown or selected until directed 
otherwise by BHT. 
 
6. If no crack is found, the intent of PART III is complete.  
 
7. Make an entry in the helicopter records to show that PART III, Option “B” of this 
bulletin is completed.   
 
8. Repeat this inspection after ev ery 500 flight-hours thereafter.  
 
9. When your tailboom reaches 8600 flight -hours, one of the additional recurring 
inspection requirements defined under PART IV must apply.

### Page 9

ASB 407-08-84 
Page 9 of 26 
 
 
PART IV Additional inspection require ments for tailbooms with 8600 flight-
hours or more or with time unknown: 
 
For tailbooms which have reached or exce eded 8600 flight-hours or with total flight-
hours unknown, in addition to PART II and PART III, incorporate to the inspection 
schedule, one of the following recurring in spections and repeat at the applicable 
interval shown; 
 
Option “A” (10X Magnifying glass 50-Hour recurring inspection): 
 
-NOTE- 
 
It is permissible to transfer from one inspection program to 
the other for maintenance scheduling convenience (ex: 
Option “A” to Option “B). However, the inspection as 
described in the new program must be accomplished prior to 
next flight. Make an entry in t he helicopter records to show 
that you have transferred from one inspection option to the 
other for traceability. 
 
1. Use a clean cloth moistened with airc raft soap (C-318) prepared in accordance 
with manufacturer’s recommendations, as  required, to remove any exhaust 
residues or dirt from both Areas “C” and “D” to look at, as shown in Figure 2. 
 
2. On left side of tailboom, make sure that the tailboom skin is clean and that 
adequate lighting exists.  Use a 10X m agnifying glass and examine tailboom 
around fasteners and just above the edge of upper  stabilizer support as shown in 
Figure 2,  Areas “C” and ”D”. 
 
3. If a crack is found, replace the tailboom with a serviceable unit prior to next flight 
and notify Bell Helicopter Product Support Engineering department; 
 
a) If another affected tailboom is installed on the helic opter, determine the total 
time in service of that tailboom and app ly appropriate inspection program as 
defined in this bulletin.  
 
b) If the total flight-time of your ta ilboom is unknown, accomplish inspection 
requirements described under PART II, PART III and PART IV before putting 
this tailboom in service and repeat at in tervals shown or selected until directed 
otherwise by BHT. 
 
4. If no crack is found, the intent of PART IV is complete.  
 
5. Make an entry in the helic opter records to show that PART IV, Option “A” of this 
bulletin is completed.

### Page 10

ASB 407-08-84 
Page 10 of 26 
 
 
 
6. Repeat this inspection after ev ery 50 flight-hours thereafter.  
 
Option “B” (Daily recurring check): 
 
-NOTE- 
 
This inspection can be performed by the pilot as part of his 
preflight check with paint/primer still present at the affected 
areas.  
-NOTE- 
 
It is permissible to transfer from one inspection program to 
the other for maintenance scheduling convenience (ex: 
Option “B” to Option “A). However, the inspection as 
described in the new program must be accomplished prior to 
next flight. Make an entry in t he helicopter records to show 
that you have transferred from one inspection option to the 
other for traceability. 
 
1. Use a clean cloth moistened with airc raft soap (C-318) prepared in accordance 
with manufacturer’s recommendations, as  required, to remove any exhaust 
residues or dirt from both Areas “C” and “D” to look at, as shown in Figure 2.  
 
2. On left side of tailboom, make sure that the tailboom skin is clean and that 
adequate lighting exists.  Examine tailboom  around fasteners and just above the 
edge of upper stabilizer support in the shad ed areas shown in Figure 2, Areas “C” 
and “D”. 
 
3. If a crack is found, replace the tailboom with a serviceable unit prior to next flight 
and notify Bell Helicopter Product Support Engineering department; 
 
a) If another affected tailboom is installed on the helic opter, determine the total 
time in service of that tailboom and app ly appropriate inspection program as 
defined in this bulletin.  
 
b) If the total flight-time of your ta ilboom is unknown, accomplish inspection 
requirements described under PART II, PART III and PART IV before putting 
this tailboom in service and repeat at in tervals shown or selected until directed 
otherwise by BHT.  
 
4. If no crack is found, the intent of PART IV is complete.  
 
5. Make an entry in the helic opter records to show that PART IV, Option “B” of this 
bulletin is completed.

### Page 11

ASB 407-08-84 
Page 11 of 26 
 
 
 
6. Repeat this inspection before firs t flight of each day thereafter.  
 
 
PART V  Instructions for Continued Airworthiness  
 
1. Maintain your tailboom in accordanc e with your 407 Main tenance Manual BHT-
407-MM-1 and the BHT corrosion control guide CSSD-PSE-87-001. 
 
2. Inspect your tailboom as per applicabl e requirements and recurring intervals as 
described herein.

### Page 12 (OCR)

ASB 407-08-84
Page 12 of 26
BS
125.74
REF
- TAILBOOM DATA PLATE IDENTIFICATION
LOOKING DOWN AT TAILBOOM
08538_01
Figure 1. Location of identification plate, tailbooms 407-030-801-201, 407-
030-801-203 or 407-030-801-205.

### Page 13 (OCR)

ASB 407-08-84
Page 13 of 26
BS
157.00
TAILBOOM IDENTIFICATION PLATE REF  BS  REF
140.428
REF
AREA D
BS
107.397
REF
BS  -AREA I
72.370
REF  -AREA H
•AREA C
- AREA B
AREA A
BS
39.00
REF
300-HOUR VISUAL INSPECTION
CRITICAL INSPECTION AREAS (SEE DETAILS) 08538_02
Figure 2.  Inspection schedule for tailbooms 407-030-801-201, 407-407-030-
801-203 and 407-030-801-205 (Sheet 1 of 6).

### Page 14 (OCR)

ASB 407-08-84
Page 14 of 26
BS  BS  BS
31.920  74.370  80.000
REF  REF  REF
BL
0.00
REF
LBL
• AREA B  7.50
REF
SEE  SEE  SEE
DETAIL E  DETAIL F  DETAIL G
BS  BS  BS  BS  BS  BS
39.000  45.515  52.600  58.995  72.475  85.955
REF  REF  REF  REF  REF  REF
AREA B
4.0 IN.
FWD  (101.6 mm
BL
0.00
REF
LBL
7.50
REF  9 FASTENERS
(LEFT SIDE ONLY)
BS
45.515
DETAIL E  REF
GENERAL VISUAL INSPECTION (300 HOURS)
CRITICAL INSPECTION AREA  08538_03
Figure 2.  Inspection schedule for tailbooms 407-030-801-201, 407-407-030-
801-203 and 407-030-801-205 (Sheet 2).

### Page 15 (OCR)

ASB 407-08-84
Page 15 of 26
FWD
BL
0.00
REF
3.5 IN. DIAMETER APPROX  - 3 RIVETS
(88.9 mm)  (LEFT SIDE ONLY)
BS  BS  BS
45.515  52.600  58.995
REF  REF  REF
DETAIL F
BS
FWD  72.475
REF
BL
0.00
REF
10 RIVETS  LBL
(LEFT SIDE ONLY)  7.50
REF
3.00 IN. -
(76.2 mm)
DETAIL G
GENERAL VISUAL INSPECTION (300 HOURS)
CRITICAL INSPECTION AREAS  08538_04
Figure 2.  Inspection schedule for tailbooms 407-030-801-201, 407-407-030-
801-203 and 407-030-801-205 (Sheet 3).

### Page 16 (OCR)

ASB 407-08-84
Page 16 of 26
4.25 IN. -  (139.7 mm)  5.5 IN
(108.0 mm)
2.0 IN.
AREA D  (50.8 mm)
AREA C
2.0 IN.
(50.8 mm)
B.S
120.75
REF
B.S
98.89  AREA C AND AREA D
REF  (HORIZONTAL STABILIZER NOT SHOWN FOR CLARITY)
GENERAL VISUAL INSPECTION (300 HOURS)
CRITICAL INSPECTION AREAS  08538_05
Figure 2.  Inspection schedule for tailbooms 407-030-801-201, 407-407-030-
801-203 and 407-030-801-205 (Sheet 4).

### Page 17 (OCR)

ASB 407-08-84
Page 17 of 26
BS
FWD  140.428
REF
BL
0.00
3V5  REF
LBL
5.00
REF
• 3.00 IN. APPROX.
(76.2 mm)
AREA H
FWD  BS
157.0
REF
78
00:0
- 2.50 IN. DIAMETER APPROX.
(63.5 mm)
- 3 RIVETS (LEFT SIDE ONLY)
AREA I
GENERAL VISUAL INSPECTION (300 HOURS)
CRITICAL INSPECTION AREAS  08538_06
Figure 2.  Inspection schedule for tailbooms 407-030-801-201, 407-407-030-
801-203 and 407-030-801-205 (Sheet 5).

### Page 18 (OCR)

ASB 407-08-84
Page 18 of 26
LEGEND:
1. Upper tailboom skin (Ref)
2. Horizontal stabilizer (Ret)
3. Left upper stabilizer attachment support (Ref)
NOTES
AT EVERY 300-HOUR INTERVAL:
1.  Inspect the complete tailboom assembly for general condition.
2.  On the left side of the tailboom only, do a detailed inspection of all areas shown
for cracks in the tailboom skin and loose rivets. Do not remove the paint or primer. If a loose rivet is found,
remove rivet and inspect hole for cracks using a 10X magnifying glass. If no cracks are found, install
correct diameter rivet. Do not exceed maximum diameter prescribed.
Use a 10X magnifying glass to inspect for cracks in tailboom skin and around fastener heads as
indicated in area shown in Details E, F, G, Areas C, D, H and I.
Do not remove horizontal stabilizer.
FOR TAILBOOMS IN SERVICE FOR 6900 FLIGHT-HOURS OR MORE, OR WITH TOTAL TIME UNKNOWN:
Inspect Area H and Area I at every 150-hour interval using 10X magnifying glass inspection method
or at every 500-hour interval using Eddy current inspection method.
FOR TAILBOOMS IN SERVICE FOR 8600 FLIGHT-HOURS OR MORE, OR WITH TOTAL TIME UNKNOWN:
Visually check Area C and Area D daily or at every 50-hour interval using 10X magnifying glass inspection
Pay close attention to skin just above edge of upper support.
8.  Some tailboom components not shown for clarity.
9.  If a crack is found on the tailboom skin, replace the tailboom before the next flight and contact Product
Support Engineering using the following information:
Bell Helicopter Textron
Product Support Engineering
Light Helicopters
Tel: 1-800-243-6407 (Continental USA and Canada)
Tel: 1-800-363-8023 (Continental USA)
Tel: 1-800-361-9305 (Within Canada)
Tel: 1-450-437-2682 (All other areas - call collect)
Fax: 450-433-0272
Email: pselight@bellhelicopter.textron.com  08538_07
Figure 2.  Inspection schedule for tailbooms 407-030-801-201, 407-407-030-
801-203 and 407-030-801-205 (Sheet 6).

### Page 19

ASB 407-08-84 
Page 19 of 26 
 
 
APPENDIX “A” 
1.0 Scope 
1.1 This procedure is provided to allo w for the detection of 0.050” crack(s) 
emanating from beneath rivet heads. 
1.2 It is intended to provide as close as prac tical detection of cracks oriented in 
both the vertical and horizontal positions. 
 
2.0 Personnel Requirements 
2.1 Personnel performing inspection to this procedure shall be qualified Level II or 
III per the requirements of NAS 410 or equivalent, OR have successfully 
completed the BHT CTA NDE Field Mainte nance course.  The individual shall 
be certified as a Level I Special in Eddy Current per employer’s written practice 
for personnel training and certification. 
 
3.0 Equipment 
3.1  NDI Instrument: Hocking Phasec 2 Eddy current flaw detector or equivalent. 
3.2  Probe: Absolute pencil probe (50-500 kHz). 
3.3  BNC cable. 
3.4  BNC cable adapter. 
3.5  Teflon tape (C-460). 
3.6  Reference standard: Aluminum 3 Notch Crack Standard (P/N 29A029). 
 
4.0 Calibration 
4.1  Non-painted surface 
4.1.1 Connect cable and probe to the Phasec 2, power ON. 
4.1.2 Place a piece of Teflon tape onto t he coil of the probe to decrease 
wearing of the probe and reduce chance of scratching the material under 
inspection. 
4.1.3 Press the MENU button to enter the setup mode. 
4.1.4 Setup instrument per Table 1. 
4.1.5 Press the MENU button to exit the setup mode. 
4.1.6 Place the pencil probe ont o a good area of  the standard away from any 
edge or crack and press the “BALANCE (load)” button as shown in Figure 
3. 
4.1.7 Lift the probe off the standard and adjust the PHASE as necessary so that 
the trace line (lift-off signal) moves fr om the center of the display to the 
left and exits the screen horizontally as shown in Figure 4.  Re- BALANCE 
with probe on the standard when complete. 
4.1.8 Sweep the probe over the 0.020” reference crack on the standard and 
verify signal response. 
4.1.9 Adjust coarse GAIN values if necessary to increase or decrease crack 
response amplitude.  Figure 5 illustrates typical response from 0.020” flaw 
(approximately one grid division).

### Page 20

ASB 407-08-84 
Page 20 of 26 
 
 
 
4.2 Painted surface 
4.2.1 Perform steps 4.1.1 through 4.1.5. 
4.2.2 BALANCE probe adjacent to the inspecti on area, then place probe on the 
reference standard (see Figure 7). 
4.2.3 The displayed balance point should ap pear to right of the previous 
balance (null) point (see Figure 6). 
4.2.4 Place one layer of notebook paper (~ 3- 4 mils thick) over the calibration 
standard, and place the pr obe on top of the paper.  The balance point 
should move left toward the center of the screen.  Perform this step 
adding additional layers of paper until the balance point returns to center.  
This step will determine t he approximate paint thic kness in the area of 
inspection and allow the operator to  compensate for any reduction of 
sensitivity due to the additional lift-off. 
4.2.5 With the determined number of  notebook paper on top of the 
standard, Balance the Eddy curr ent probe, and complete steps 
4.1.7 through 4.1.9.  
 
NOTE: Any type of paper may be used when compensating for paint 
thickness.  The main consideration is that the paper (or any other 
material, i.e. plastic shim, tape, etc.) is electrically non-conductive. 
 
5.0 Pre-Inspection 
5.1 Ensure surfaces are clean and free of any  loose debris, so as not to interfere 
with the inspection. 
 
6.0 Inspection 
6.1 Place the probe in intimate contact with the rivet area(s) to be inspected and 
Re-adjust the PHASE, if necessary, so that lift-off is horizontal from center null 
point to left.  
6.2 Scan the area of interest circumferentia lly (see Figure 7) while monitoring the 
display for a sudden increase in signal amplitude from crack-like indications. 
 
7.0 Evaluation 
7.1 Repeat calibration and rescan any areas w here there is a vertical crack-like 
deflection. 
7.2   If indication persists, mark the location on the part. 
 
8.0 Accept/Reject Criteria  
8.1 Any repeatable crack-like indi cation detected by the Eddy Current method      
shall be cause for rejection.

### Page 21

ASB 407-08-84 
Page 21 of 26 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Gain        30.0/ 40.0 
X dB                30.0 
Y dB                40.0 
Phase             201.0 
 
FREQ.            200.0 
 
HIPASS             DC 
LOPASS Hz      100.0 
BAND LOCK   OFF 
 
PROBE       
Absolute 
LOAD Uh          120 
INPUT GAIN    High 
 
 
RECALL        Setup 
SAVE             Trace 
TRACE RECORD  ---  
OFF 
ALARM SHAPE   Off 
TOP                        ---- 
BOTTOM               ---- 
LEFT                      ---- 
RIGHT                   ---- 
START ANGLE    ---- 
END ANGLE        ---- 
INNER                   ---- 
OUTER                  ---- 
 
STRETCH            50 ms 
ALARM ACTION None 
 
DISPLAY             Spot 
SWEEP                 5.0 s 
PERSIST               0.2 s 
 
GRATICULE      Grid 1 
SPOT X                  50% 
SPOT Y                  50% 
MODE         Normal  
PROBE  I D   
Unknown 
 
POWER DOWN ----    
Off 
KEY CLICK      Off  
CONTRAST       A/R 
VIDEO MODE  --- 
Normal 
LANGUAGE  --- 
English 
BAUD              9600 
 
 
TIME                A/R 
DAY                 A/R 
MONTH           A/R 
YEAR               A/R 
 
    
      Table 1

### Page 22 (OCR)

ASB 407-08-84
Page 22 of 26
BALANCE
"LOAD"
BNC CABLE  08538_08
ADAPTER
FIGURE 3

### Page 23 (OCR)

ASB 407-08-84
Page 23 of 26
LIFT-OFF
DIRECTION
balance
clear  the re
Phasec  GAIN dB 30.0/40.0
OK
08538_09
FIGURE 4

### Page 24 (OCR)

ASB 407-08-84
Page 24 of 26
0.020 IN.
EDM NOTCH
balance
clear
freeze
PHASE  FRED
Phasec  GRIN dB 30.0/40.0
OK
exec
08538_10
FIGURE 5

### Page 25 (OCR)

ASB 407-08-84
Page 25 of 26
CHANGE IN BALANCE POINT
WHEN THE PROBE IS MOVED
TO THE BARE STANDARD
Phasec  CAIN dB 30.0/40.0
NULL POINT WHEN
BALANCED ON A
PAINTED SURFACE
08538_11
Balance probe between fasteners adjacent to the area under inspection (see Figure 7)
and then place probe onto a flaw free area of the bare aluminum standard. The lift-off
signal should continue past the original NULL point. This difference is due to the
thickness of paint on the aircraft.
NOTE
After the appropriate amount of notebook paper has been added, signal will move
to center Null point.
FIGURE 6

### Page 26 (OCR)

ASB 407-08-84
Page 26 of 26
WHEN INSPECTING PAINTED
SURFACES, DETERMINE PAINT  Vertical
THICKNESS AS DESCRIBED BY
BALANCING THE EDDY CURRENT
PROBE IN AN ADJACENT AREA, AND
FOLLOWING THE STEPS DESCRIBED
IN SECTION 4.2
08538_12
Inspect by placing the Eddy current probe directly against the edge of the
fastener head as shown, and scanning completely around the entire
circumference of the fastener.
FIGURE 7

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
