# Bell Alert Service Bulletin 407-16-113: No revision named

- Rights: © Bell Textron Inc. Filed by the FAA in regulations.gov docket FAA-2017-0667; AD 2018-10-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Bell Alert Service Bulletin 407-16-113](https://openairdocs.org/service-documents/bell/sb-407-16-113.md)
- Title as filed: BHTC ASB_407-16-113
- Pages: 5
- PDF: https://openairdocs.org/files/sha256/97/b6/97b6b59ec88552bbd534662ccfd97797e8cf3a832e3471f67cddae707124fb6a
- Page: https://openairdocs.org/service-documents/bell/sb-407-16-113/file/97b6b59ec885

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ASB 407-16-113 
Page 1 of 5 
Approved for public release. 
 
 
 
 
 
  ALERT SERVICE BULLETIN 407-16-113 
12 February 2016 
 
MODEL AFFECTED:  407 
 
SUBJECT: TAIL ROTOR DRIVESHAFT SEGMENT 
ASSEMBLY, INSPECTION OF 
 
HELICOPTERS AFFECTED: S erial numbers 53000 through 53900, 53911 
through 54166, and 54300 through 54657. 
 
 [Serial number 54541, 54556, 54567, 54570, 54594, 
54609, 54611, 54614, 54619, 64646, 54647, 54648, 
54658 and subsequent  will have the intent of this 
bulletin accomplished prior to delivery.] 
 
COMPLIANCE: For helicopters with more than 4000 flight hours, to 
be accomplished within 50 hours  but no later than 
March 12, 2016. 
 
 For helicopters with 300 to 4000 flight hours, to be 
accomplished within 100 hours  but no later than 
May 12, 2016. 
 
DESCRIPTION: 
 
Bell Helicopter has been made aware of an incident where the tail rotor (T/R) 
driveshaft assembly failed to provide drive to the T/R gearbox assembly. As a 
precautionary measure, Bell is introducing a one- time inspection to verify for any axial 
or rotational play between the T/R driveshafts and adapters, as well as a torque check 
of the retention nuts that are used to clamp-up the installation. We are also introducing 
clarification to the inspection requirements of the same assembly in the 
scheduled/periodic inspection programs of the BHT-407-MM Maintenance Manual. 
Helicopters with less than 300 flight hours at the time of release of this ASB or that 
reach 300 flight hours after May 12, 2016, are not affected by this bulletin.  The 
Progressive and Periodic Inspection Programs contained in the BHT -407-MM-1 
(Chapter 5) Maintenance Manual meet the intent of this ASB.  
Applicability of this bulletin to any spare part shall be determined prior to its installation 
on an affected helicopter.

### Page 2

ASB 407-16-113 
Page 2 of 5 
Approved for public release. 
APPROVAL: 
 
The engineering design aspects of this bulletin are Transport Canada Civil Aviation 
(TCCA) approved. 
 
CONTACT INFO: 
 
For any questions regarding this bulletin, please contact: 
 
Bell Helicopter Product Support Engineering - Light Helicopters 
Tel: 450-437-2862 / 1-800-363-8023 / pselight@bh.com 
 
MANPOWER: 
 
Approximately 3 man-hours are required to complete this bulletin.  This estimate is 
based on hands-on time and may vary with personnel and facilities available. 
 
WARRANTY: 
 
There is no warranty credit applicable for parts or labor associated with this bulletin. 
 
MATERIAL: 
 
Required Material: 
The following material is required for the accomplishment of this bulletin and may be 
obtained through your Bell Helicopter Textron Supply Center. 
 
Part Number Nomenclature Qty Notes  
     
NAS1149F0432P Washer 4 1, 3  
MS21042L4 Nut 4 1, 2, 3  
406-040-327-101 Washer 4 1, 3  
406-040-328-105 Adapter 4 1, 3  
407-040-330-107 Shaft Assembly 4 1, 3  
 
Notes:  
1. Required quantities will vary depending on inspection findings. 
2. NAS9926-4L may be used as an alternate part. 
3. A complete tail rotor driveshaft segment assembly 407- 040-302-117S may be 
used in lieu of individual parts. 
 
Consumable Material: 
The following material is required to accomplish this bulletin, but may not require 
ordering, depending on the operator’s consumable material stock levels.  This material 
may be obtained through your Bell Helicopter Textron Supply Center.

### Page 3

ASB 407-16-113 
Page 3 of 5 
Approved for public release. 
Part Number Nomenclature Qty Reference * 
    
2400-11378-00 Mobil 28 Grease A/R C-001 
 
* C-XXX numbers refer to the consumables list in the BHT-ALL-SPM, Standard Practices Manual 
 
SPECIAL TOOLS: 
 
T102146-101 Bearing alignment tool. 
 
WEIGHT AND BALANCE: 
 
Not affected. 
 
ELECTRICAL LOAD DATA: 
 
Not affected. 
 
REFERENCES: 
 
BHT-407-IPB, Illustrated Parts Breakdown 
BHT-407-MM, Maintenance Manual 
BHT-ALL-SPM, Standard Practice Manual 
 
PUBLICATIONS AFFECTED: 
 
BHT-407-MM, Maintenance Manual, Chapters 5 and 65. 
 
ACCOMPLISHMENT INSTRUCTIONS: 
 
1. Prepare the helicopter for maintenance. 
2. Gain access to the tail rotor (T/R) driveshaft segment assemblies (1, 2, 3, and 4, 
Figure 1) by removing T/R driveshaft covers from the tailboom assembly (11). 
3. Inspect for any noticeable rotational or axial (fore and aft) play between adapter (8) 
and T/R driveshaft (12) at all four positions (1, 2, 3, and 4). 
a. Note findings for each T/R driveshaft segment assembly (1, 2, 3, and 4) for 
future reference in the following steps. 
4. Remove aft short shaft assembly (BHT-407-MM-7, Chapter 65). 
-NOTE- 
 
Put a support under the aft end of the T/R driveshaft 
segment assembly (2) of position 2.

### Page 4

ASB 407-16-113 
Page 4 of 5 
Approved for public release. 
5. Remove T/R driveshaft segment assemblies from position 1 and 3 (1 and 3) of the 
tailboom assembly (11) (BHT-407-MM-7, Chapter 65). 
6. Perform torque check  of T/R adapter retention nut ( 5) on all four drive shaft 
segment assemblies (1, 2, 3, and 4). 
a. Check for minimum torque of 30 inch-pounds (5.7 Nm). 
b. Note findings for each retention nut ( 5) for future reference in the following 
steps. 
7. If rotational or axial play was noted in step 3, or minimum torque was not met in 
step 6, remove adapter (8) from applicable driveshaft assembly (1, 2, 3, or 4) and 
inspect associated parts (6, 7, 8, and 12)  for allowable damage limit s 
(BHT-407-MM-7, Chapter 65), otherwise go to step 8. 
a. Replace retention nut ( 5) with new  nut, and repair or replace other parts as 
required. 
CAUTION 
 
Position washer (7) with tapered side facing away from 
adapter (8, Section C- C). Otherwise, damage to the part will 
occur. 
 
b. Install the adapter ( 8), washers (7 and 6), and nut ( 5). Torque  the nut 30 to  
50 inch-pounds (5.7 to 7.9 Nm) plus tare torque of nut (BHT-ALL-SPM). 
8. Install removed T/R driveshaft assemblies (1 and 3) (BHT-407-MM, Chapter 65). 
9. Perform T/R driveshaft segment assembly bearing alignment procedure at all four 
locations (1, 2, 3, and 4) (BHT-407-MM-7, Chapter 65). 
10. Install short shaft assembly removed in step 4 (BHT-407-MM-7, Chapter 65). 
11. Lubricate all four bearings (10) as required (BHT-407-MM-2, Chapter 12). 
12. Install T/R driveshaft covers removed in step 2 (BHT-407-MM-7, Chapter 65). 
13. Make an entry in the helicopter logbook and historical service records indicating 
compliance with this Alert Service Bulletin.

### Page 5 (OCR)

SEE DETAIL A
SEE DETAIL B
DETAIL A
10)
DETAIL B
(TYPICAL 4 PLACES)
Tail rotor driveshaft segment assembly position 1
~  Tail rotor driveshaft segment assembly position 2
3.  Tail rotor driveshaft segment assembly position 3  SECTION C-C
4.  Tail rotor driveshaft segment assembly position 4  AFTER INSTALLATION
Nut
Washer
Washer
8. Coupling adapter
9. Grease fitting
10. Bearing
11. Tailboom assembly
12. Tail rotor driveshaft
13. Bearing hanger
14. Retaining ring
30 TO 50 IN-LBS
(5.7 TO 7.9 Nm)
16646_001
Figure 1 - Tail Rotor Driveshaft Segment Assembly Installation
ASB 407-16-113
Page 5 of 5
Approved for public release.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
