# Boeing Alert Requirements Bulletin 717-57A0027 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2020-1028; AD 2021-12-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 717-57A0027 RB](https://openairdocs.org/service-documents/boeing/717-57a0027-rb.md)
- Title as filed: 717-57A0027_RB_R00
- Pages: 14
- PDF: https://openairdocs.org/files/sha256/a0/92/a092a3b31742c14b733cb901405a72dde6d7fe1951ed2f4f8f34c6042e7e854c
- Page: https://openairdocs.org/service-documents/boeing/717-57a0027-rb/file/a092a3b31742

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
717
Requirements Bulletin
ALERT
Number: 717-57A0027 RB
Original Issue: June 26, 2020
ATA System: 5771
SUBJECT: WINGS - Inboard and Outboard Spoilers - Spoiler Assembly Doublers and Splice Bar
Inspection
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
Copyright © 2020 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: June 26, 2020
717-57A0027 RB
1 of 14
3.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 26, 2020
717-57A0027 RB
2 of 14
REQUIREMENTS BULLETIN 717-57A0027
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. ACCOMPLISHMENT INSTR UCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
FIGURE 1: LEFT AND RIGHT WING - INBOARD AND OUTBOARD SPOILERS - GENERAL VISUAL
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 26, 2020
717-57A0027 RB
3 of 14
REQUIREMENTS BULLETIN 717-57A0027
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 26, 2020
717-57A0027 RB
4 of 14
REQUIREMENTS BULLETIN 717-57A0027
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
717
Requirements Bulletin
ALERT
Number: 717-57A0027 RB
Original Issue: June 26, 2020
ATA System: 5771
SUBJECT: WINGS - Inboard and Outboard Spoilers - Spoiler Assembly Doublers and Splice Bar
Inspection
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 717-200 Airplane(s), line number(s) 5002-5156 in 1 Group(s).Where
the effectivity is presented with hyphens between line numbers, the airplane applicability means
"through" and "inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.
DESCRIPTIONCONFIGURATIONGROUP
All 717-200 airplanes-1
Airplane Models:
717-200
GroupFuselage Number
15002 - 5099
GroupFuselage Number
15100 - 5156
GroupFuselage Number
--
B. Spares Affected
Examine your spares supply for the parts or components identified below. If any parts or components
are found, refer to Accomplishment Instructions for the recommended action.
After accomplishing the inspection given in this bulletin, do not install on any airplane any spare
parts listed below unless they have been inspected and applicable on-condition corrective action
has been done in accordance with the Accomplishment Instructions given in this bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 26, 2020
717-57A0027 RB
5 of 14

### Page 6

Part NamePart Number
SPOILER ASSY - WING FLIGHT5940974-1
SPOILER ASSY - WING FLIGHT5940974-2
SPOILER ASSY - WING FLIGHT5940974-501
SPOILER ASSY - WING FLIGHT5940974-502
SPLICE BAR - FLIGHT3914588-501
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 717-57A0027 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements bulletin 717-57A0027 RB mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table 1, in accordance with
Accomplishment Instructions.
Table 1: Left and Right Wing - Inboard and Outboard Spoilers - General Visual Inspection for Correct
Splice Bar and Doublers
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 6,400 flight hours or 27
months after the original issue
date of Requirements bulletin 717-
57A0027 RB, whichever occurs
first.
Do a General Visual In-
spection (GVI) of the left
and right wing inboard
and outboard spoiler as-
semblies for correct
splice bar & doublers
configuration.
All Airplanes.
-Before further flight.Contact the Boeing Com-
pany for repair instruc-
tions and do the repair.
CONDITION 1: Any incor-
rect inboard and outboard
spoiler assembly configura-
tion found.
--No further action re-
quired.
CONDITION 2: No incor-
rect inboard and outboard
spoiler assembly configura-
tion found.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 26, 2020
717-57A0027 RB
6 of 14
REQUIREMENTS BULLETIN 717-57A0027
ALERTALERT

### Page 7

4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity.This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 26, 2020
717-57A0027 RB
7 of 14
REQUIREMENTS BULLETIN 717-57A0027
ALERTALERT

### Page 8

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 26, 2020
717-57A0027 RB
8 of 14
REQUIREMENTS BULLETIN 717-57A0027
ALERTALERT
BLANK PAGE

### Page 9

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Boeing Service Letter 717-SL-51-107, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions.The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
5. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 717 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 717
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 717
Aircraft Maintenance Manual (AMM).
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 26, 2020
717-57A0027 RB
9 of 14
REQUIREMENTS BULLETIN 717-57A0027
ALERTALERT

### Page 10

— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
6. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
7. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
8. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
9. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
10. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance, unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked. Basic cleaning may be
required to ensure appropriate visibility.
11. The instructions in Work Instructions and the figures can include operation of tools
or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool and
Equipment Manual, and the Special Tool and Ground Handling Drawing Index contain
data on versions of the tools or test equipment that you can use. It is permitted to
use replaced tools. It is not permitted to use superseded tools.
12. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 26, 2020
717-57A0027 RB
10 of 14
REQUIREMENTS BULLETIN 717-57A0027
ALERTALERT

### Page 11

Left and Right Wing - Inboard and Outboard Spoilers - General Visual Inspection for Correct Splice Bar
and Doublers
Refer to the listed proce-
dures in SB 717-
57A0027 Original Issue
or later approved revi-
sions as an accepted
procedure.
METHOD OF COMPLI-
ANCE
ACTIONCONDITION
PART 1: OPEN ACCESS--All Airplanes
-FIGURE 1Do a General Visual Inspec-
tion (GVI) of the left and
right wing inboard and out-
board spoiler assemblies
for correct splice bar &
doublers configuration.
--Contact the Boeing Compa-
ny for repair instructions
and do the repair.
CONDITION 1: Any incor-
rect inboard and outboard
spoiler assembly configura-
tion found. PART 2: CLOSE AC-
CESS
--
--No further action required.CONDITION 2: No incor-
rect inboard and outboard
spoiler assembly configura-
tion found.
PART 2: CLOSE AC-
CESS
--
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 26, 2020
717-57A0027 RB
11 of 14
REQUIREMENTS BULLETIN 717-57A0027
ALERTALERT

### Page 12 (OCR)

REQUIREMENTS BULLETIN 717-57A0027
ALERT  ALERT
SPOILER
SPLICE BAR
DOUBLER
DOUBLER
DOUBLER  INBD MAIN SPOILER
ACTUATOR SUPPORT
SPLICE BAR  FITTING ASSEMBLY
DOUBLER
SPOILER
OUTBD MAIN SPOILER
ACTUATOR SUPPORT  INBOARD AND OUTBOARD MAIN
FITTING ASSEMBLY  SPOILER ASSEMBLIES
2925652
FIGURE 1: LEFT AND RIGHT WING - INBOARD AND OUTBOARD SPOILERS - GENERAL VISUAL
INSPECTION
(SHEET 1 OF 3)
Original Issue: June 26, 2020
Export Controlled ECCN: 9E991  717-57A0027 RB
Copyright © Unpublished
Work - See page 1 for details.  12 of 14

### Page 13 (OCR)

REQUIREMENTS BULLETIN 717-57A0027
ALERT  ALERT
SPOILER
SPLICE BAR
- DOUBLER
INBD MAIN SPOILER  DOUBLER
ACTUATOR SUPPORT
FITTING ASSEMBLY  SPLICE BAR
SPOILER
INBOARD AND OUTBOARD MAIN
SPOILER ASSEMBLIES
OUTBD MAIN SPOILER
ACTUATOR SUPPORT
FITTING ASSEMBLY
2925673
FIGURE 1: LEFT AND RIGHT WING - INBOARD AND OUTBOARD SPOILERS - GENERAL VISUAL
INSPECTION
(SHEET 2 OF 3)
Original Issue: June 26, 2020
Export Controlled ECCN: 9E991  Copyright © Unpublished  717-57A0027 RB
Work - See page 1 for details.  13 of 14

### Page 14

More DataQtyIdentificationNameTaskStep
(a)(b)2-SPOILER ASSEMBLYInspect1
(a)(b)2-SPOILER ASSEMBLYInspect2
(a) Do a General Visual Inspection (GVI) of the inboard and outboard spoiler assemblies for correct splice
bar and doublers configuration.
(b) Spoiler Assembly with correct doubler and splice bar configuration shown.
FIGURE 1: LEFT AND RIGHT WING - INBOARD AND OUTBOARD SPOILERS - GENERAL VISUAL
INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 26, 2020
717-57A0027 RB
14 of 14
REQUIREMENTS BULLETIN 717-57A0027
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
